* [PATCH v3 1/10] ohci-nxp: Driver cleanup
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 2/10] ohci-nxp: Device tree support Roland Stigge
` (8 subsequent siblings)
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
Cleanup for ohci-nxp.c:
* Cleanup of resource handling (mem and irq), use devm_request_and_ioremap()
* Use DMA_BIT_MASK()
* Don't remove __devinit
* Removed obsolete gpio.h include
* More consistent bit access symbols
* Removed unused extern declaration ocpi_enable()
* Added error handling on i2c_get_adapter()
* Whitespace cleanup
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Applies to v3.4-rc3
drivers/usb/host/ohci-nxp.c | 44 ++++++++++++++++++++++++++------------------
1 file changed, 26 insertions(+), 18 deletions(-)
--- linux-2.6.orig/drivers/usb/host/ohci-nxp.c
+++ linux-2.6/drivers/usb/host/ohci-nxp.c
@@ -29,7 +29,6 @@
#include <mach/platform.h>
#include <mach/irqs.h>
-#include <asm/gpio.h>
#define USB_CONFIG_BASE 0x31020000
#define PWRMAN_BASE 0x40004000
@@ -38,7 +37,9 @@
/* USB_CTRL bit defines */
#define USB_SLAVE_HCLK_EN (1 << 24)
+#define USB_DEV_NEED_CLK_EN (1 << 22)
#define USB_HOST_NEED_CLK_EN (1 << 21)
+#define PAD_CONTROL_LAST_DRIVEN (1 << 19)
#define USB_OTG_CLK_CTRL IO_ADDRESS(USB_CONFIG_BASE + 0xFF4)
#define USB_OTG_CLK_STAT IO_ADDRESS(USB_CONFIG_BASE + 0xFF8)
@@ -117,7 +118,6 @@ static struct i2c_driver isp1301_driver;
static struct i2c_client *isp1301_i2c_client;
extern int usb_disabled(void);
-extern int ocpi_enable(void);
static struct clk *usb_clk;
@@ -220,7 +220,7 @@ static void isp1301_configure_lpc32xx(vo
ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
/* Enable usb_need_clk clock after transceiver is initialized */
- __raw_writel((__raw_readl(USB_CTRL) | (1 << 22)), USB_CTRL);
+ __raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL);
printk(KERN_INFO "ISP1301 Vendor ID : 0x%04x\n",
i2c_smbus_read_word_data(isp1301_i2c_client, 0x00));
@@ -374,9 +374,13 @@ static int __devinit usb_hcd_nxp_probe(s
const struct hc_driver *driver = &ohci_nxp_hc_driver;
struct i2c_adapter *i2c_adap;
struct i2c_board_info i2c_info;
+ struct resource *res;
int ret = 0, irq;
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+
dev_dbg(&pdev->dev, "%s: " DRIVER_DESC " (nxp)\n", hcd_name);
if (usb_disabled()) {
err("USB is disabled");
@@ -384,16 +388,8 @@ static int __devinit usb_hcd_nxp_probe(s
goto out;
}
- if (pdev->num_resources != 2
- || pdev->resource[0].flags != IORESOURCE_MEM
- || pdev->resource[1].flags != IORESOURCE_IRQ) {
- err("Invalid resource configuration");
- ret = -ENODEV;
- goto out;
- }
-
/* Enable AHB slave USB clock, needed for further USB clock control */
- __raw_writel(USB_SLAVE_HCLK_EN | (1 << 19), USB_CTRL);
+ __raw_writel(USB_SLAVE_HCLK_EN | PAD_CONTROL_LAST_DRIVEN, USB_CTRL);
ret = i2c_add_driver(&isp1301_driver);
if (ret < 0) {
@@ -401,6 +397,11 @@ static int __devinit usb_hcd_nxp_probe(s
goto out;
}
i2c_adap = i2c_get_adapter(2);
+ if (!i2c_adap) {
+ err("failed on i2c_get_adapter");
+ goto out_i2c_driver;
+ }
+
memset(&i2c_info, 0, sizeof(struct i2c_board_info));
strlcpy(i2c_info.type, "isp1301_nxp", I2C_NAME_SIZE);
isp1301_i2c_client = i2c_new_probed_device(i2c_adap, &i2c_info,
@@ -442,7 +443,7 @@ static int __devinit usb_hcd_nxp_probe(s
while ((__raw_readl(USB_OTG_CLK_STAT) & USB_CLOCK_MASK) !=
USB_CLOCK_MASK) ;
- hcd = usb_create_hcd (driver, &pdev->dev, dev_name(&pdev->dev));
+ hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
if (!hcd) {
err("Failed to allocate HC buffer");
ret = -ENOMEM;
@@ -452,14 +453,21 @@ static int __devinit usb_hcd_nxp_probe(s
/* Set all USB bits in the Start Enable register */
nxp_set_usb_bits();
- hcd->rsrc_start = pdev->resource[0].start;
- hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
- if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
- dev_dbg(&pdev->dev, "request_mem_region failed\n");
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Failed to get MEM resource");
+ ret = -ENOMEM;
+ goto out4;
+ }
+
+ hcd->regs = devm_request_and_ioremap(&pdev->dev, res);
+ if (!hcd->regs) {
+ err("Failed to devm_request_and_ioremap");
ret = -ENOMEM;
goto out4;
}
- hcd->regs = (void __iomem *)pdev->resource[0].start;
+ hcd->rsrc_start = res->start;
+ hcd->rsrc_len = resource_size(res);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 2/10] ohci-nxp: Device tree support
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
2012-04-18 13:36 ` [PATCH v3 1/10] ohci-nxp: Driver cleanup Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 3/10] ARM: LPC32xx: clock.c cleanup Roland Stigge
` (7 subsequent siblings)
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch adds device tree support to ohci-nxp.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Applies to v3.4-rc3
Documentation/devicetree/bindings/usb/ohci-nxp.txt | 16 ++++++++++++++++
drivers/usb/host/ohci-nxp.c | 10 ++++++++++
2 files changed, 26 insertions(+)
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/usb/ohci-nxp.txt
@@ -0,0 +1,16 @@
+* OHCI controller, NXP ohci-nxp variant
+
+Required properties:
+- compatible: must be "nxp,ohci-nxp"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: The OHCI interrupt
+
+Example (LPC32xx):
+
+ ohci@31020000 {
+ compatible = "nxp,ohci-nxp";
+ reg = <0x31020000 0x300>;
+ interrupt-parent = <&mic>;
+ interrupts = <0x3b 0>;
+ };
--- linux-2.6.orig/drivers/usb/host/ohci-nxp.c
+++ linux-2.6/drivers/usb/host/ohci-nxp.c
@@ -22,6 +22,7 @@
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
+#include <linux/of.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -525,10 +526,19 @@ static int usb_hcd_nxp_remove(struct pla
/* work with hotplug and coldplug */
MODULE_ALIAS("platform:usb-ohci");
+#ifdef CONFIG_OF
+static const struct of_device_id usb_hcd_nxp_match[] = {
+ { .compatible = "nxp,ohci-nxp" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, usb_hcd_nxp_match);
+#endif
+
static struct platform_driver usb_hcd_nxp_driver = {
.driver = {
.name = "usb-ohci",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(usb_hcd_nxp_match),
},
.probe = usb_hcd_nxp_probe,
.remove = usb_hcd_nxp_remove,
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 3/10] ARM: LPC32xx: clock.c cleanup
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
2012-04-18 13:36 ` [PATCH v3 1/10] ohci-nxp: Driver cleanup Roland Stigge
2012-04-18 13:36 ` [PATCH v3 2/10] ohci-nxp: Device tree support Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 4/10] ARM: LPC32xx: clock.c dma adjustment Roland Stigge
` (6 subsequent siblings)
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch makes use of the default macro CLKDEV_INIT() for clock registration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Applies to v3.4-rc3
---
arch/arm/mach-lpc32xx/clock.c | 77 +++++++++++++++++++-----------------------
1 file changed, 35 insertions(+), 42 deletions(-)
--- linux-2.6.orig/arch/arm/mach-lpc32xx/clock.c
+++ linux-2.6/arch/arm/mach-lpc32xx/clock.c
@@ -1095,49 +1095,42 @@ struct clk *clk_get_parent(struct clk *c
}
EXPORT_SYMBOL(clk_get_parent);
-#define _REGISTER_CLOCK(d, n, c) \
- { \
- .dev_id = (d), \
- .con_id = (n), \
- .clk = &(c), \
- },
-
static struct clk_lookup lookups[] = {
- _REGISTER_CLOCK(NULL, "osc_32KHz", osc_32KHz)
- _REGISTER_CLOCK(NULL, "osc_pll397", osc_pll397)
- _REGISTER_CLOCK(NULL, "osc_main", osc_main)
- _REGISTER_CLOCK(NULL, "sys_ck", clk_sys)
- _REGISTER_CLOCK(NULL, "arm_pll_ck", clk_armpll)
- _REGISTER_CLOCK(NULL, "ck_pll5", clk_usbpll)
- _REGISTER_CLOCK(NULL, "hclk_ck", clk_hclk)
- _REGISTER_CLOCK(NULL, "pclk_ck", clk_pclk)
- _REGISTER_CLOCK(NULL, "timer0_ck", clk_timer0)
- _REGISTER_CLOCK(NULL, "timer1_ck", clk_timer1)
- _REGISTER_CLOCK(NULL, "timer2_ck", clk_timer2)
- _REGISTER_CLOCK(NULL, "timer3_ck", clk_timer3)
- _REGISTER_CLOCK(NULL, "vfp9_ck", clk_vfp9)
- _REGISTER_CLOCK(NULL, "clk_dmac", clk_dma)
- _REGISTER_CLOCK("pnx4008-watchdog", NULL, clk_wdt)
- _REGISTER_CLOCK(NULL, "uart3_ck", clk_uart3)
- _REGISTER_CLOCK(NULL, "uart4_ck", clk_uart4)
- _REGISTER_CLOCK(NULL, "uart5_ck", clk_uart5)
- _REGISTER_CLOCK(NULL, "uart6_ck", clk_uart6)
- _REGISTER_CLOCK("pnx-i2c.0", NULL, clk_i2c0)
- _REGISTER_CLOCK("pnx-i2c.1", NULL, clk_i2c1)
- _REGISTER_CLOCK("pnx-i2c.2", NULL, clk_i2c2)
- _REGISTER_CLOCK("dev:ssp0", NULL, clk_ssp0)
- _REGISTER_CLOCK("dev:ssp1", NULL, clk_ssp1)
- _REGISTER_CLOCK("lpc32xx_keys.0", NULL, clk_kscan)
- _REGISTER_CLOCK("lpc32xx-nand.0", "nand_ck", clk_nand)
- _REGISTER_CLOCK("lpc32xx-adc", NULL, clk_adc)
- _REGISTER_CLOCK(NULL, "i2s0_ck", clk_i2s0)
- _REGISTER_CLOCK(NULL, "i2s1_ck", clk_i2s1)
- _REGISTER_CLOCK("ts-lpc32xx", NULL, clk_tsc)
- _REGISTER_CLOCK("dev:mmc0", NULL, clk_mmc)
- _REGISTER_CLOCK("lpc-eth.0", NULL, clk_net)
- _REGISTER_CLOCK("dev:clcd", NULL, clk_lcd)
- _REGISTER_CLOCK("lpc32xx_udc", "ck_usbd", clk_usbd)
- _REGISTER_CLOCK("lpc32xx_rtc", NULL, clk_rtc)
+ CLKDEV_INIT(NULL, "osc_32KHz", &osc_32KHz),
+ CLKDEV_INIT(NULL, "osc_pll397", &osc_pll397),
+ CLKDEV_INIT(NULL, "osc_main", &osc_main),
+ CLKDEV_INIT(NULL, "sys_ck", &clk_sys),
+ CLKDEV_INIT(NULL, "arm_pll_ck", &clk_armpll),
+ CLKDEV_INIT(NULL, "ck_pll5", &clk_usbpll),
+ CLKDEV_INIT(NULL, "hclk_ck", &clk_hclk),
+ CLKDEV_INIT(NULL, "pclk_ck", &clk_pclk),
+ CLKDEV_INIT(NULL, "timer0_ck", &clk_timer0),
+ CLKDEV_INIT(NULL, "timer1_ck", &clk_timer1),
+ CLKDEV_INIT(NULL, "timer2_ck", &clk_timer2),
+ CLKDEV_INIT(NULL, "timer3_ck", &clk_timer3),
+ CLKDEV_INIT(NULL, "vfp9_ck", &clk_vfp9),
+ CLKDEV_INIT(NULL, "clk_dmac", &clk_dma),
+ CLKDEV_INIT("pnx4008-watchdog", NULL, &clk_wdt),
+ CLKDEV_INIT(NULL, "uart3_ck", &clk_uart3),
+ CLKDEV_INIT(NULL, "uart4_ck", &clk_uart4),
+ CLKDEV_INIT(NULL, "uart5_ck", &clk_uart5),
+ CLKDEV_INIT(NULL, "uart6_ck", &clk_uart6),
+ CLKDEV_INIT("pnx-i2c.0", NULL, &clk_i2c0),
+ CLKDEV_INIT("pnx-i2c.1", NULL, &clk_i2c1),
+ CLKDEV_INIT("pnx-i2c.2", NULL, &clk_i2c2),
+ CLKDEV_INIT("dev:ssp0", NULL, &clk_ssp0),
+ CLKDEV_INIT("dev:ssp1", NULL, &clk_ssp1),
+ CLKDEV_INIT("lpc32xx_keys.0", NULL, &clk_kscan),
+ CLKDEV_INIT("lpc32xx-nand.0", "nand_ck", &clk_nand),
+ CLKDEV_INIT("lpc32xx-adc", NULL, &clk_adc),
+ CLKDEV_INIT(NULL, "i2s0_ck", &clk_i2s0),
+ CLKDEV_INIT(NULL, "i2s1_ck", &clk_i2s1),
+ CLKDEV_INIT("ts-lpc32xx", NULL, &clk_tsc),
+ CLKDEV_INIT("dev:mmc0", NULL, &clk_mmc),
+ CLKDEV_INIT("lpc-eth.0", NULL, &clk_net),
+ CLKDEV_INIT("dev:clcd", NULL, &clk_lcd),
+ CLKDEV_INIT("lpc32xx_udc", "ck_usbd", &clk_usbd),
+ CLKDEV_INIT("lpc32xx_rtc", NULL, &clk_rtc),
};
static int __init clk_init(void)
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 4/10] ARM: LPC32xx: clock.c dma adjustment
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (2 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 3/10] ARM: LPC32xx: clock.c cleanup Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 5/10] ARM: LPC32xx: Remove obsolete platform Kconfig Roland Stigge
` (5 subsequent siblings)
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch adjusts the DMA clock of the LPC32xx to "pl08xdmac" to be picked up
correctly by the AMBA dmaengine driver.
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
arch/arm/mach-lpc32xx/clock.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
--- linux-2.6.orig/arch/arm/mach-lpc32xx/clock.c
+++ linux-2.6/arch/arm/mach-lpc32xx/clock.c
@@ -1109,7 +1109,7 @@ static struct clk_lookup lookups[] = {
CLKDEV_INIT(NULL, "timer2_ck", &clk_timer2),
CLKDEV_INIT(NULL, "timer3_ck", &clk_timer3),
CLKDEV_INIT(NULL, "vfp9_ck", &clk_vfp9),
- CLKDEV_INIT(NULL, "clk_dmac", &clk_dma),
+ CLKDEV_INIT("pl08xdmac", NULL, &clk_dma),
CLKDEV_INIT("pnx4008-watchdog", NULL, &clk_wdt),
CLKDEV_INIT(NULL, "uart3_ck", &clk_uart3),
CLKDEV_INIT(NULL, "uart4_ck", &clk_uart4),
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 5/10] ARM: LPC32xx: Remove obsolete platform Kconfig
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (3 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 4/10] ARM: LPC32xx: clock.c dma adjustment Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 6/10] input: Device tree support for LPC32xx touchscreen Roland Stigge
` (4 subsequent siblings)
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch removes two Kconfig options now unused (the network driver is
configured via DT now).
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Applies to v3.4-rc3
--- linux-2.6.orig/arch/arm/mach-lpc32xx/Kconfig
+++ linux-2.6/arch/arm/mach-lpc32xx/Kconfig
@@ -29,30 +29,4 @@ config ARCH_LPC32XX_UART6_SELECT
endmenu
-menu "LPC32XX chip components"
-
-config ARCH_LPC32XX_IRAM_FOR_NET
- bool "Use IRAM for network buffers"
- default y
- help
- Say Y here to use the LPC internal fast IRAM (i.e. 256KB SRAM) as
- network buffer. If the total combined required buffer sizes is
- larger than the size of IRAM, then SDRAM will be used instead.
-
- This can be enabled safely if the IRAM is not intended for other
- uses.
-
-config ARCH_LPC32XX_MII_SUPPORT
- bool "Check to enable MII support or leave disabled for RMII support"
- help
- Say Y here to enable MII support, or N for RMII support. Regardless of
- which support is selected, the ethernet interface driver needs to be
- selected in the device driver networking section.
-
- The PHY3250 reference board uses RMII, so users of this board should
- say N.
-
-endmenu
-
endif
-
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 6/10] input: Device tree support for LPC32xx touchscreen
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (4 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 5/10] ARM: LPC32xx: Remove obsolete platform Kconfig Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 7/10] iio: lpc32xx-adc: Remove driver conflict due to device tree Roland Stigge
` (3 subsequent siblings)
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch adds device tree support for the LPC32xx SoC's touchscreen
controller.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
---
Applies to v3.4-rc3
Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt | 16 ++++++++++
drivers/input/touchscreen/lpc32xx_ts.c | 10 ++++++
2 files changed, 26 insertions(+)
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt
@@ -0,0 +1,16 @@
+* NXP LPC32xx SoC Touchscreen Controller (TSC)
+
+Required properties:
+- compatible: must be "nxp,lpc32xx-tsc"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: The TSC/ADC interrupt
+
+Example:
+
+ tsc@40048000 {
+ compatible = "nxp,lpc32xx-tsc";
+ reg = <0x40048000 0x1000>;
+ interrupt-parent = <&mic>;
+ interrupts = <39 0>;
+ };
--- linux-2.6.orig/drivers/input/touchscreen/lpc32xx_ts.c
+++ linux-2.6/drivers/input/touchscreen/lpc32xx_ts.c
@@ -22,6 +22,7 @@
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/slab.h>
+#include <linux/of.h>
/*
* Touchscreen controller register offsets
@@ -383,6 +384,14 @@ static const struct dev_pm_ops lpc32xx_t
#define LPC32XX_TS_PM_OPS NULL
#endif
+#ifdef CONFIG_OF
+static struct of_device_id lpc32xx_tsc_of_match[] = {
+ { .compatible = "nxp,lpc32xx-tsc", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, lpc32xx_tsc_of_match);
+#endif
+
static struct platform_driver lpc32xx_ts_driver = {
.probe = lpc32xx_ts_probe,
.remove = __devexit_p(lpc32xx_ts_remove),
@@ -390,6 +399,7 @@ static struct platform_driver lpc32xx_ts
.name = MOD_NAME,
.owner = THIS_MODULE,
.pm = LPC32XX_TS_PM_OPS,
+ .of_match_table = of_match_ptr(lpc32xx_tsc_of_match),
},
};
module_platform_driver(lpc32xx_ts_driver);
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 7/10] iio: lpc32xx-adc: Remove driver conflict due to device tree
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (5 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 6/10] input: Device tree support for LPC32xx touchscreen Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 22:02 ` Greg KH
2012-04-18 13:36 ` [PATCH v3 8/10] ARM: LPC32xx: DTS files for device tree conversion Roland Stigge
` (2 subsequent siblings)
9 siblings, 1 reply; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
Previously, the touchscreen and ADC drivers of the LPC32xx SoC had a Kconfig
conflict declared because they use the same hardware. Upon the introduction of
device tree support in both drivers, the conflict must be removed to enable
the same kernel to support different hardware (configured via the device tree).
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Applies to v3.4-rc3
drivers/staging/iio/adc/Kconfig | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
--- linux-2.6.orig/drivers/staging/iio/adc/Kconfig
+++ linux-2.6/drivers/staging/iio/adc/Kconfig
@@ -195,11 +195,13 @@ config MAX1363_RING_BUFFER
config LPC32XX_ADC
tristate "NXP LPC32XX ADC"
- depends on ARCH_LPC32XX && !TOUCHSCREEN_LPC32XX
+ depends on ARCH_LPC32XX
help
Say yes here to build support for the integrated ADC inside the
LPC32XX SoC. Note that this feature uses the same hardware as the
- touchscreen driver, so you can only select one of the two drivers
- (lpc32xx_adc or lpc32xx_ts). Provides direct access via sysfs.
+ touchscreen driver, so you should either select only one of the two
+ drivers (lpc32xx_adc or lpc32xx_ts) or, in the OpenFirmware case,
+ activate only one via device tree selection. Provides direct access
+ via sysfs.
endmenu
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v3 7/10] iio: lpc32xx-adc: Remove driver conflict due to device tree
2012-04-18 13:36 ` [PATCH v3 7/10] iio: lpc32xx-adc: Remove driver conflict due to device tree Roland Stigge
@ 2012-04-18 22:02 ` Greg KH
0 siblings, 0 replies; 12+ messages in thread
From: Greg KH @ 2012-04-18 22:02 UTC (permalink / raw)
To: Roland Stigge
Cc: arm, linux-arm-kernel, thierry.reding, linux-usb, linux-kernel,
linux-input, dmitry.torokhov, axel.lin, broonie, marek.vasut,
devel, kevin.wells, srinivas.bakki, dan.carpenter
On Wed, Apr 18, 2012 at 03:36:12PM +0200, Roland Stigge wrote:
> Previously, the touchscreen and ADC drivers of the LPC32xx SoC had a Kconfig
> conflict declared because they use the same hardware. Upon the introduction of
> device tree support in both drivers, the conflict must be removed to enable
> the same kernel to support different hardware (configured via the device tree).
>
> Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v3 8/10] ARM: LPC32xx: DTS files for device tree conversion
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (6 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 7/10] iio: lpc32xx-adc: Remove driver conflict due to device tree Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 9/10] ARM: LPC32xx: Device tree support Roland Stigge
2012-04-18 13:36 ` [PATCH v3 10/10] ARM: LPC32xx: Move common code to common.c Roland Stigge
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch adds the dts files for the reference machine of LPC32xx:
* arch/arm/boot/dts/lpc32xx.dtsi: Include for devices based on LPC32xx
* arch/arm/boot/dts/phy3250.dts: Board support for PHYTEC phyCORE-LPC3250
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
arch/arm/boot/dts/lpc32xx.dtsi | 289 +++++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/phy3250.dts | 145 ++++++++++++++++++++
2 files changed, 434 insertions(+)
--- /dev/null
+++ linux-2.6/arch/arm/boot/dts/lpc32xx.dtsi
@@ -0,0 +1,289 @@
+/*
+ * NXP LPC32xx SoC
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ compatible = "nxp,lpc32xx";
+ interrupt-parent = <&mic>;
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,arm926ejs";
+ };
+ };
+
+ ahb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x20000000 0x20000000 0x30000000>;
+
+ slc: flash@20020000 {
+ compatible = "nxp,nand-slc";
+ reg = <0x20020000 0x1000>;
+ status = "disable";
+ };
+
+ mlc: flash@200B0000 {
+ compatible = "nxp,nand-mlc";
+ reg = <0x200B0000 0x1000>;
+ status = "disable";
+ };
+
+ dma@31000000 {
+ compatible = "arm,pl080", "arm,primecell";
+ reg = <0x31000000 0x1000>;
+ interrupts = <0x1c 0>;
+ };
+
+ /*
+ * Enable either ohci or usbd (gadget)!
+ */
+ ohci@31020000 {
+ compatible = "nxp,ohci-nxp", "usb-ohci";
+ reg = <0x31020000 0x300>;
+ interrupts = <0x3b 0>;
+ status = "disable";
+ };
+
+ usbd@31020000 {
+ compatible = "nxp,lpc32xx-udc";
+ reg = <0x31020000 0x300>;
+ interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>;
+ status = "disable";
+ };
+
+ clcd@31040000 {
+ compatible = "arm,pl110", "arm,primecell";
+ reg = <0x31040000 0x1000>;
+ interrupts = <0x0e 0>;
+ status = "disable";
+ };
+
+ mac: ethernet@31060000 {
+ compatible = "nxp,lpc-eth";
+ reg = <0x31060000 0x1000>;
+ interrupts = <0x1d 0>;
+ };
+
+ apb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x20000000 0x20000000 0x30000000>;
+
+ ssp0: ssp@20084000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x20084000 0x1000>;
+ interrupts = <0x14 0>;
+ };
+
+ spi1: spi@20088000 {
+ compatible = "nxp,spi";
+ reg = <0x20088000 0x1000>;
+ };
+
+ ssp1: ssp@2008c000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x2008c000 0x1000>;
+ interrupts = <0x15 0>;
+ };
+
+ spi2: spi@20090000 {
+ compatible = "nxp,spi";
+ reg = <0x20090000 0x1000>;
+ };
+
+ i2s0: i2s@20094000 {
+ compatible = "nxp,i2s";
+ reg = <0x20094000 0x1000>;
+ };
+
+ sd@20098000 {
+ compatible = "arm,pl180", "arm,primecell";
+ reg = <0x20098000 0x1000>;
+ interrupts = <0x0f 0>, <0x0d 0>;
+ };
+
+ i2s1: i2s@2009C000 {
+ compatible = "nxp,i2s";
+ reg = <0x2009C000 0x1000>;
+ };
+
+ uart3: serial@40080000 {
+ compatible = "nxp,serial";
+ reg = <0x40080000 0x1000>;
+ };
+
+ uart4: serial@40088000 {
+ compatible = "nxp,serial";
+ reg = <0x40088000 0x1000>;
+ };
+
+ uart5: serial@40090000 {
+ compatible = "nxp,serial";
+ reg = <0x40090000 0x1000>;
+ };
+
+ uart6: serial@40098000 {
+ compatible = "nxp,serial";
+ reg = <0x40098000 0x1000>;
+ };
+
+ i2c1: i2c@400A0000 {
+ compatible = "nxp,pnx-i2c";
+ reg = <0x400A0000 0x100>;
+ interrupts = <0x33 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pnx,timeout = <0x64>;
+ };
+
+ i2c2: i2c@400A8000 {
+ compatible = "nxp,pnx-i2c";
+ reg = <0x400A8000 0x100>;
+ interrupts = <0x32 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pnx,timeout = <0x64>;
+ };
+
+ i2cusb: i2c@31020300 {
+ compatible = "nxp,pnx-i2c";
+ reg = <0x31020300 0x100>;
+ interrupts = <0x3f 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pnx,timeout = <0x64>;
+ };
+ };
+
+ fab {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0x20000000 0x20000000 0x30000000>;
+
+ /*
+ * MIC Interrupt controller includes:
+ * MIC @40008000
+ * SIC1 @4000C000
+ * SIC2 @40010000
+ */
+ mic: interrupt-controller@40008000 {
+ compatible = "nxp,lpc32xx-mic";
+ interrupt-controller;
+ reg = <0x40008000 0xC000>;
+ #interrupt-cells = <2>;
+ };
+
+ uart1: serial@40014000 {
+ compatible = "nxp,serial";
+ reg = <0x40014000 0x1000>;
+ };
+
+ uart2: serial@40018000 {
+ compatible = "nxp,serial";
+ reg = <0x40018000 0x1000>;
+ };
+
+ uart7: serial@4001C000 {
+ compatible = "nxp,serial";
+ reg = <0x4001C000 0x1000>;
+ };
+
+ rtc@40024000 {
+ compatible = "nxp,lpc32xx-rtc";
+ reg = <0x40024000 0x1000>;
+ interrupts = <0x34 0>;
+ };
+
+ gpio: gpio@40028000 {
+ compatible = "nxp,lpc32xx-gpio";
+ reg = <0x40028000 0x1000>;
+ /* create a private address space for enumeration */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio_p0: gpio-bank@0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0>;
+ };
+
+ gpio_p1: gpio-bank@1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <1>;
+ };
+
+ gpio_p2: gpio-bank@2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <2>;
+ };
+
+ gpio_p3: gpio-bank@3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <3>;
+ };
+
+ gpi_p3: gpio-bank@4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <4>;
+ };
+
+ gpo_p3: gpio-bank@5 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <5>;
+ };
+ };
+
+ watchdog@4003C000 {
+ compatible = "nxp,pnx4008-wdt";
+ reg = <0x4003C000 0x1000>;
+ };
+
+ /*
+ * TSC vs. ADC: Since those two share the same
+ * hardware, you need to choose from one of the
+ * following two and do 'status = "okay";" for one of
+ * them
+ */
+
+ adc@40048000 {
+ compatible = "nxp,lpc32xx-adc";
+ reg = <0x40048000 0x1000>;
+ interrupts = <0x27 0>;
+ status = "disable";
+ };
+
+ tsc@40048000 {
+ compatible = "nxp,lpc32xx-tsc";
+ reg = <0x40048000 0x1000>;
+ interrupts = <0x27 0>;
+ status = "disable";
+ };
+
+ key@40050000 {
+ compatible = "nxp,key";
+ reg = <0x40050000 0x1000>;
+ };
+
+ };
+ };
+};
--- /dev/null
+++ linux-2.6/arch/arm/boot/dts/phy3250.dts
@@ -0,0 +1,145 @@
+/*
+ * PHYTEC phyCORE-LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "lpc32xx.dtsi"
+
+/ {
+ model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
+ compatible = "phytec,phy3250", "nxp,lpc32xx";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x4000000>;
+ };
+
+ ahb {
+ mac: ethernet@31060000 {
+ phy-mode = "rmii";
+ use-iram;
+ };
+
+ /* Here, choose exactly one from: ohci, usbd */
+ ohci@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+
+/*
+ usbd@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+*/
+
+ clcd@31040000 {
+ status = "okay";
+ };
+
+ /* 64MB Flash via SLC NAND controller */
+ slc: flash@20020000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mtd0@00000000 {
+ label = "phy3250-boot";
+ reg = <0x00000000 0x00064000>;
+ read-only;
+ };
+
+ mtd1@00064000 {
+ label = "phy3250-uboot";
+ reg = <0x00064000 0x00190000>;
+ read-only;
+ };
+
+ mtd2@001f4000 {
+ label = "phy3250-ubt-prms";
+ reg = <0x001f4000 0x00010000>;
+ };
+
+ mtd3@00204000 {
+ label = "phy3250-kernel";
+ reg = <0x00204000 0x00400000>;
+ };
+
+ mtd4@00604000 {
+ label = "phy3250-rootfs";
+ reg = <0x00604000 0x039fc000>;
+ };
+ };
+
+ apb {
+ i2c1: i2c@400A0000 {
+ clock-frequency = <0x186a0>;
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ uda1380: uda1380@18 {
+ compatible = "nxp,uda1380";
+ reg = <0x18>;
+ power-gpio = <&gpio 0x59 0>;
+ reset-gpio = <&gpio 0x51 0>;
+ dac-clk = "wspll";
+ };
+ };
+
+ i2c2: i2c@400A8000 {
+ clock-frequency = <0x186a0>;
+ };
+
+ i2cusb: i2c@31020300 {
+ clock-frequency = <0x186a0>;
+
+ isp1301: usb-transceiver@2c {
+ compatible = "nxp,isp1301";
+ reg = <0x2c>;
+ };
+ };
+
+ ssp0: ssp@20084000 {
+ eeprom: at25@0 {
+ compatible = "atmel,at25";
+ };
+ };
+ };
+
+ fab {
+ tsc@40048000 {
+ status = "okay";
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 {
+ gpios = <&gpo_p3 1 1>; /* GPO_P3 1, GPIO 80, active low */
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ led1 {
+ gpios = <&gpo_p3 14 1>; /* GPO_P3 14, GPIO 93, active low */
+ linux,default-trigger = "timer";
+ default-state = "off";
+ };
+ };
+};
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 9/10] ARM: LPC32xx: Device tree support
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (7 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 8/10] ARM: LPC32xx: DTS files for device tree conversion Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
2012-04-18 13:36 ` [PATCH v3 10/10] ARM: LPC32xx: Move common code to common.c Roland Stigge
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch does the actual device tree switch for the LPC32xx SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
Applies to v3.4-rc3
Documentation/devicetree/bindings/arm/lpc32xx-mic.txt | 38 +++
Documentation/devicetree/bindings/arm/lpc32xx.txt | 8
arch/arm/Kconfig | 1
arch/arm/mach-lpc32xx/common.c | 192 ------------------
arch/arm/mach-lpc32xx/common.h | 14 -
arch/arm/mach-lpc32xx/irq.c | 78 +++++--
arch/arm/mach-lpc32xx/phy3250.c | 147 +++++--------
7 files changed, 167 insertions(+), 311 deletions(-)
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/arm/lpc32xx-mic.txt
@@ -0,0 +1,38 @@
+* NXP LPC32xx Main Interrupt Controller
+ (MIC, including SIC1 and SIC2 secondary controllers)
+
+Required properties:
+- compatible: Should be "nxp,lpc32xx-mic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: Empty for the interrupt controller itself
+- #interrupt-cells: The number of cells to define the interrupts. Should be 2.
+ The first cell is the IRQ number
+ The second cell is used to specify mode:
+ 1 = low-to-high edge triggered
+ 2 = high-to-low edge triggered
+ 4 = active high level-sensitive
+ 8 = active low level-sensitive
+ Default for internal sources should be set to 4 (active high).
+- reg: Should contain MIC registers location and length
+
+Examples:
+ /*
+ * MIC
+ */
+ mic: interrupt-controller@40008000 {
+ compatible = "nxp,lpc32xx-mic";
+ interrupt-controller;
+ interrupt-parent;
+ #interrupt-cells = <2>;
+ reg = <0x40008000 0xC000>;
+ };
+
+ /*
+ * ADC
+ */
+ adc@40048000 {
+ compatible = "nxp,lpc32xx-adc";
+ reg = <0x40048000 0x1000>;
+ interrupt-parent = <&mic>;
+ interrupts = <39 4>;
+ };
--- /dev/null
+++ linux-2.6/Documentation/devicetree/bindings/arm/lpc32xx.txt
@@ -0,0 +1,8 @@
+NXP LPC32xx Platforms Device Tree Bindings
+------------------------------------------
+
+Boards with the NXP LPC32xx SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "nxp,lpc32xx";
--- linux-2.6.orig/arch/arm/Kconfig
+++ linux-2.6/arch/arm/Kconfig
@@ -597,6 +597,7 @@ config ARCH_LPC32XX
select USB_ARCH_HAS_OHCI
select CLKDEV_LOOKUP
select GENERIC_CLOCKEVENTS
+ select USE_OF
help
Support for the NXP LPC32XX family of processors
--- linux-2.6.orig/arch/arm/mach-lpc32xx/common.c
+++ linux-2.6/arch/arm/mach-lpc32xx/common.c
@@ -32,198 +32,6 @@
#include "common.h"
/*
- * Watchdog timer
- */
-static struct resource watchdog_resources[] = {
- [0] = {
- .start = LPC32XX_WDTIM_BASE,
- .end = LPC32XX_WDTIM_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-struct platform_device lpc32xx_watchdog_device = {
- .name = "pnx4008-watchdog",
- .id = -1,
- .num_resources = ARRAY_SIZE(watchdog_resources),
- .resource = watchdog_resources,
-};
-
-/*
- * I2C busses
- */
-static struct resource i2c0_resources[] = {
- [0] = {
- .start = LPC32XX_I2C1_BASE,
- .end = LPC32XX_I2C1_BASE + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_LPC32XX_I2C_1,
- .end = IRQ_LPC32XX_I2C_1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- [0] = {
- .start = LPC32XX_I2C2_BASE,
- .end = LPC32XX_I2C2_BASE + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_LPC32XX_I2C_2,
- .end = IRQ_LPC32XX_I2C_2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c2_resources[] = {
- [0] = {
- .start = LPC32XX_OTG_I2C_BASE,
- .end = LPC32XX_OTG_I2C_BASE + 0x100 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_LPC32XX_USB_I2C,
- .end = IRQ_LPC32XX_USB_I2C,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_i2c0_device = {
- .name = "pnx-i2c",
- .id = 0,
- .num_resources = ARRAY_SIZE(i2c0_resources),
- .resource = i2c0_resources,
-};
-
-struct platform_device lpc32xx_i2c1_device = {
- .name = "pnx-i2c",
- .id = 1,
- .num_resources = ARRAY_SIZE(i2c1_resources),
- .resource = i2c1_resources,
-};
-
-struct platform_device lpc32xx_i2c2_device = {
- .name = "pnx-i2c",
- .id = 2,
- .num_resources = ARRAY_SIZE(i2c2_resources),
- .resource = i2c2_resources,
-};
-
-/* TSC (Touch Screen Controller) */
-
-static struct resource lpc32xx_tsc_resources[] = {
- {
- .start = LPC32XX_ADC_BASE,
- .end = LPC32XX_ADC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_LPC32XX_TS_IRQ,
- .end = IRQ_LPC32XX_TS_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_tsc_device = {
- .name = "ts-lpc32xx",
- .id = -1,
- .num_resources = ARRAY_SIZE(lpc32xx_tsc_resources),
- .resource = lpc32xx_tsc_resources,
-};
-
-/* RTC */
-
-static struct resource lpc32xx_rtc_resources[] = {
- {
- .start = LPC32XX_RTC_BASE,
- .end = LPC32XX_RTC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },{
- .start = IRQ_LPC32XX_RTC,
- .end = IRQ_LPC32XX_RTC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_rtc_device = {
- .name = "rtc-lpc32xx",
- .id = -1,
- .num_resources = ARRAY_SIZE(lpc32xx_rtc_resources),
- .resource = lpc32xx_rtc_resources,
-};
-
-/*
- * ADC support
- */
-static struct resource adc_resources[] = {
- {
- .start = LPC32XX_ADC_BASE,
- .end = LPC32XX_ADC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_LPC32XX_TS_IRQ,
- .end = IRQ_LPC32XX_TS_IRQ,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-struct platform_device lpc32xx_adc_device = {
- .name = "lpc32xx-adc",
- .id = -1,
- .num_resources = ARRAY_SIZE(adc_resources),
- .resource = adc_resources,
-};
-
-/*
- * USB support
- */
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = ~(u32) 0;
-static struct resource ohci_resources[] = {
- {
- .start = IO_ADDRESS(LPC32XX_USB_BASE),
- .end = IO_ADDRESS(LPC32XX_USB_BASE + 0x100 - 1),
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_LPC32XX_USB_HOST,
- .flags = IORESOURCE_IRQ,
- },
-};
-struct platform_device lpc32xx_ohci_device = {
- .name = "usb-ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = 0xFFFFFFFF,
- },
- .num_resources = ARRAY_SIZE(ohci_resources),
- .resource = ohci_resources,
-};
-
-/*
- * Network Support
- */
-static struct resource net_resources[] = {
- [0] = DEFINE_RES_MEM(LPC32XX_ETHERNET_BASE, SZ_4K),
- [1] = DEFINE_RES_MEM(LPC32XX_IRAM_BASE, SZ_128K),
- [2] = DEFINE_RES_IRQ(IRQ_LPC32XX_ETHERNET),
-};
-
-static u64 lpc32xx_mac_dma_mask = 0xffffffffUL;
-struct platform_device lpc32xx_net_device = {
- .name = "lpc-eth",
- .id = 0,
- .dev = {
- .dma_mask = &lpc32xx_mac_dma_mask,
- .coherent_dma_mask = 0xffffffffUL,
- },
- .num_resources = ARRAY_SIZE(net_resources),
- .resource = net_resources,
-};
-
-/*
* Returns the unique ID for the device
*/
void lpc32xx_get_uid(u32 devid[4])
--- linux-2.6.orig/arch/arm/mach-lpc32xx/common.h
+++ linux-2.6/arch/arm/mach-lpc32xx/common.h
@@ -23,26 +23,12 @@
#include <linux/platform_device.h>
/*
- * Arch specific platform device structures
- */
-extern struct platform_device lpc32xx_watchdog_device;
-extern struct platform_device lpc32xx_i2c0_device;
-extern struct platform_device lpc32xx_i2c1_device;
-extern struct platform_device lpc32xx_i2c2_device;
-extern struct platform_device lpc32xx_tsc_device;
-extern struct platform_device lpc32xx_adc_device;
-extern struct platform_device lpc32xx_rtc_device;
-extern struct platform_device lpc32xx_ohci_device;
-extern struct platform_device lpc32xx_net_device;
-
-/*
* Other arch specific structures and functions
*/
extern struct sys_timer lpc32xx_timer;
extern void __init lpc32xx_init_irq(void);
extern void __init lpc32xx_map_io(void);
extern void __init lpc32xx_serial_init(void);
-extern void __init lpc32xx_gpio_init(void);
extern void lpc23xx_restart(char, const char *);
--- linux-2.6.orig/arch/arm/mach-lpc32xx/irq.c
+++ linux-2.6/arch/arm/mach-lpc32xx/irq.c
@@ -22,6 +22,11 @@
#include <linux/irq.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/module.h>
#include <mach/irqs.h>
#include <mach/hardware.h>
@@ -44,6 +49,9 @@
#define SIC1_ATR_DEFAULT 0x00026000
#define SIC2_ATR_DEFAULT 0x00000000
+static struct irq_domain *lpc32xx_mic_domain;
+static struct device_node *lpc32xx_mic_np;
+
struct lpc32xx_event_group_regs {
void __iomem *enab_reg;
void __iomem *edge_reg;
@@ -203,7 +211,7 @@ static void lpc32xx_mask_irq(struct irq_
{
unsigned int reg, ctrl, mask;
- get_controller(d->irq, &ctrl, &mask);
+ get_controller(d->hwirq, &ctrl, &mask);
reg = __raw_readl(LPC32XX_INTC_MASK(ctrl)) & ~mask;
__raw_writel(reg, LPC32XX_INTC_MASK(ctrl));
@@ -213,7 +221,7 @@ static void lpc32xx_unmask_irq(struct ir
{
unsigned int reg, ctrl, mask;
- get_controller(d->irq, &ctrl, &mask);
+ get_controller(d->hwirq, &ctrl, &mask);
reg = __raw_readl(LPC32XX_INTC_MASK(ctrl)) | mask;
__raw_writel(reg, LPC32XX_INTC_MASK(ctrl));
@@ -223,14 +231,14 @@ static void lpc32xx_ack_irq(struct irq_d
{
unsigned int ctrl, mask;
- get_controller(d->irq, &ctrl, &mask);
+ get_controller(d->hwirq, &ctrl, &mask);
__raw_writel(mask, LPC32XX_INTC_RAW_STAT(ctrl));
/* Also need to clear pending wake event */
- if (lpc32xx_events[d->irq].mask != 0)
- __raw_writel(lpc32xx_events[d->irq].mask,
- lpc32xx_events[d->irq].event_group->rawstat_reg);
+ if (lpc32xx_events[d->hwirq].mask != 0)
+ __raw_writel(lpc32xx_events[d->hwirq].mask,
+ lpc32xx_events[d->hwirq].event_group->rawstat_reg);
}
static void __lpc32xx_set_irq_type(unsigned int irq, int use_high_level,
@@ -274,22 +282,22 @@ static int lpc32xx_set_irq_type(struct i
switch (type) {
case IRQ_TYPE_EDGE_RISING:
/* Rising edge sensitive */
- __lpc32xx_set_irq_type(d->irq, 1, 1);
+ __lpc32xx_set_irq_type(d->hwirq, 1, 1);
break;
case IRQ_TYPE_EDGE_FALLING:
/* Falling edge sensitive */
- __lpc32xx_set_irq_type(d->irq, 0, 1);
+ __lpc32xx_set_irq_type(d->hwirq, 0, 1);
break;
case IRQ_TYPE_LEVEL_LOW:
/* Low level sensitive */
- __lpc32xx_set_irq_type(d->irq, 0, 0);
+ __lpc32xx_set_irq_type(d->hwirq, 0, 0);
break;
case IRQ_TYPE_LEVEL_HIGH:
/* High level sensitive */
- __lpc32xx_set_irq_type(d->irq, 1, 0);
+ __lpc32xx_set_irq_type(d->hwirq, 1, 0);
break;
/* Other modes are not supported */
@@ -298,7 +306,7 @@ static int lpc32xx_set_irq_type(struct i
}
/* Ok to use the level handler for all types */
- irq_set_handler(d->irq, handle_level_irq);
+ irq_set_handler(d->hwirq, handle_level_irq);
return 0;
}
@@ -307,33 +315,33 @@ static int lpc32xx_irq_wake(struct irq_d
{
unsigned long eventreg;
- if (lpc32xx_events[d->irq].mask != 0) {
- eventreg = __raw_readl(lpc32xx_events[d->irq].
+ if (lpc32xx_events[d->hwirq].mask != 0) {
+ eventreg = __raw_readl(lpc32xx_events[d->hwirq].
event_group->enab_reg);
if (state)
- eventreg |= lpc32xx_events[d->irq].mask;
+ eventreg |= lpc32xx_events[d->hwirq].mask;
else {
- eventreg &= ~lpc32xx_events[d->irq].mask;
+ eventreg &= ~lpc32xx_events[d->hwirq].mask;
/*
* When disabling the wakeup, clear the latched
* event
*/
- __raw_writel(lpc32xx_events[d->irq].mask,
- lpc32xx_events[d->irq].
+ __raw_writel(lpc32xx_events[d->hwirq].mask,
+ lpc32xx_events[d->hwirq].
event_group->rawstat_reg);
}
__raw_writel(eventreg,
- lpc32xx_events[d->irq].event_group->enab_reg);
+ lpc32xx_events[d->hwirq].event_group->enab_reg);
return 0;
}
/* Clear event */
- __raw_writel(lpc32xx_events[d->irq].mask,
- lpc32xx_events[d->irq].event_group->rawstat_reg);
+ __raw_writel(lpc32xx_events[d->hwirq].mask,
+ lpc32xx_events[d->hwirq].event_group->rawstat_reg);
return -ENODEV;
}
@@ -353,6 +361,7 @@ static void __init lpc32xx_set_default_m
}
static struct irq_chip lpc32xx_irq_chip = {
+ .name = "MIC",
.irq_ack = lpc32xx_ack_irq,
.irq_mask = lpc32xx_mask_irq,
.irq_unmask = lpc32xx_unmask_irq,
@@ -386,9 +395,23 @@ static void lpc32xx_sic2_handler(unsigne
}
}
+static int __init __lpc32xx_mic_of_init(struct device_node *node,
+ struct device_node *parent)
+{
+ lpc32xx_mic_np = node;
+
+ return 0;
+}
+
+static const struct of_device_id mic_of_match[] __initconst = {
+ { .compatible = "nxp,lpc32xx-mic", .data = __lpc32xx_mic_of_init },
+ { }
+};
+
void __init lpc32xx_init_irq(void)
{
unsigned int i;
+ int irq_base;
/* Setup MIC */
__raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_MIC_BASE));
@@ -448,4 +471,19 @@ void __init lpc32xx_init_irq(void)
LPC32XX_CLKPWR_PIN_RS);
__raw_writel(__raw_readl(LPC32XX_CLKPWR_INT_RS),
LPC32XX_CLKPWR_INT_RS);
+
+ of_irq_init(mic_of_match);
+
+ irq_base = irq_alloc_descs(-1, 0, NR_IRQS, 0);
+ if (irq_base < 0) {
+ pr_warn("Cannot allocate irq_descs, assuming pre-allocated\n");
+ irq_base = 0;
+ }
+
+ lpc32xx_mic_domain = irq_domain_add_legacy(lpc32xx_mic_np, NR_IRQS,
+ irq_base, 0,
+ &irq_domain_simple_ops,
+ NULL);
+ if (!lpc32xx_mic_domain)
+ panic("Unable to add MIC irq domain\n");
}
--- linux-2.6.orig/arch/arm/mach-lpc32xx/phy3250.c
+++ linux-2.6/arch/arm/mach-lpc32xx/phy3250.c
@@ -1,8 +1,9 @@
/*
- * arch/arm/mach-lpc32xx/phy3250.c
+ * Platform support for LPC32xx SoC
*
* Author: Kevin Wells <kevin.wells@nxp.com>
*
+ * Copyright (C) 2012 Roland Stigge <stigge@antcom.de>
* Copyright (C) 2010 NXP Semiconductors
*
* This program is free software; you can redistribute it and/or modify
@@ -25,11 +26,16 @@
#include <linux/device.h>
#include <linux/spi/spi.h>
#include <linux/spi/eeprom.h>
-#include <linux/leds.h>
#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/amba/pl022.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/amba/pl08x.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -47,7 +53,6 @@
#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
-#define LED_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 1)
/*
* AMBA LCD controller
@@ -150,9 +155,6 @@ static struct clcd_board lpc32xx_clcd_da
.remove = lpc32xx_clcd_remove,
};
-static AMBA_AHB_DEVICE(lpc32xx_clcd, "dev:clcd", 0,
- LPC32XX_LCD_BASE, { IRQ_LPC32XX_LCD }, &lpc32xx_clcd_data);
-
/*
* AMBA SSP (SPI)
*/
@@ -180,8 +182,11 @@ static struct pl022_ssp_controller lpc32
.enable_dma = 0,
};
-static AMBA_APB_DEVICE(lpc32xx_ssp0, "dev:ssp0", 0,
- LPC32XX_SSP0_BASE, { IRQ_LPC32XX_SSP0 }, &lpc32xx_ssp0_data);
+static struct pl022_ssp_controller lpc32xx_ssp1_data = {
+ .bus_id = 1,
+ .num_chipselect = 1,
+ .enable_dma = 0,
+};
/* AT25 driver registration */
static int __init phy3250_spi_board_register(void)
@@ -221,73 +226,32 @@ static int __init phy3250_spi_board_regi
}
arch_initcall(phy3250_spi_board_register);
-static struct i2c_board_info __initdata phy3250_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("pcf8563", 0x51),
- },
+static struct pl08x_platform_data pl08x_pd = {
};
-static struct gpio_led phy_leds[] = {
- {
- .name = "led0",
- .gpio = LED_GPIO,
- .active_low = 1,
- .default_trigger = "heartbeat",
- },
+static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
+ OF_DEV_AUXDATA("nxp,lpc32xx-adc", 0x40048000, "lpc32xx-adc", NULL),
+ OF_DEV_AUXDATA("nxp,lpc32xx-tsc", 0x40048000, "ts-lpc32xx", NULL),
+ OF_DEV_AUXDATA("nxp,pnx-i2c", 0x400A0000, "pnx-i2c.0", NULL),
+ OF_DEV_AUXDATA("nxp,pnx-i2c", 0x400A8000, "pnx-i2c.1", NULL),
+ OF_DEV_AUXDATA("nxp,pnx-i2c", 0x31020300, "pnx-i2c.2", NULL),
+ OF_DEV_AUXDATA("nxp,lpc32xx-rtc", 0x40024000, "lpc32xx_rtc", NULL),
+ OF_DEV_AUXDATA("nxp,lpc-eth", 0x31060000, "lpc-eth.0", NULL),
+ OF_DEV_AUXDATA("nxp,pnx4008-wdt", 0x4003C000, "pnx4008-watchdog", NULL),
+ OF_DEV_AUXDATA("nxp,lpc32xx-gpio", 0x40028000, "lpc32xx-gpio", NULL),
+ OF_DEV_AUXDATA("nxp,ohci-nxp", 0x31020000, "usb-ohci", NULL),
+ OF_DEV_AUXDATA("nxp,lpc32xx-udc", 0x31020000, "lpc32xx_udc", NULL),
+ OF_DEV_AUXDATA("arm,pl022", 0x20084000, "dev:ssp0", &lpc32xx_ssp0_data),
+ OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
+ OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
+ OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
+ OF_DEV_AUXDATA("arm,pl180", 0x20098000, "dev:mmc0", NULL),
+ { }
};
-static struct gpio_led_platform_data led_data = {
- .leds = phy_leds,
- .num_leds = ARRAY_SIZE(phy_leds),
-};
-
-static struct platform_device lpc32xx_gpio_led_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev.platform_data = &led_data,
-};
-
-static struct platform_device *phy3250_devs[] __initdata = {
- &lpc32xx_rtc_device,
- &lpc32xx_tsc_device,
- &lpc32xx_i2c0_device,
- &lpc32xx_i2c1_device,
- &lpc32xx_i2c2_device,
- &lpc32xx_watchdog_device,
- &lpc32xx_gpio_led_device,
- &lpc32xx_adc_device,
- &lpc32xx_ohci_device,
- &lpc32xx_net_device,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
- &lpc32xx_clcd_device,
- &lpc32xx_ssp0_device,
-};
-
-/*
- * Board specific functions
- */
-static void __init phy3250_board_init(void)
+static void __init lpc3250_machine_init(void)
{
u32 tmp;
- int i;
-
- lpc32xx_gpio_init();
-
- /* Register GPIOs used on this board */
- if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
- printk(KERN_ERR "Error requesting gpio %u",
- SPI0_CS_GPIO);
- else if (gpio_direction_output(SPI0_CS_GPIO, 1))
- printk(KERN_ERR "Error setting gpio %u to output",
- SPI0_CS_GPIO);
-
- /* Setup network interface for RMII mode */
- tmp = __raw_readl(LPC32XX_CLKPWR_MACCLK_CTRL);
- tmp &= ~LPC32XX_CLKPWR_MACCTRL_PINS_MSK;
- tmp |= LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS;
- __raw_writel(tmp, LPC32XX_CLKPWR_MACCLK_CTRL);
/* Setup SLC NAND controller muxing */
__raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
@@ -300,6 +264,12 @@ static void __init phy3250_board_init(vo
tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
__raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
+ /* Set up USB power */
+ tmp = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
+ tmp |= LPC32XX_CLKPWR_USBCTRL_HCLK_EN |
+ LPC32XX_CLKPWR_USBCTRL_USBI2C_EN;
+ __raw_writel(tmp, LPC32XX_CLKPWR_USB_CTRL);
+
/* Set up I2C pull levels */
tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
@@ -321,33 +291,35 @@ static void __init phy3250_board_init(vo
/*
* AMBA peripheral clocks need to be enabled prior to AMBA device
* detection or a data fault will occur, so enable the clocks
- * here. However, we don't want to enable them if the peripheral
- * isn't included in the image
+ * here.
*/
-#ifdef CONFIG_FB_ARMCLCD
tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
__raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
LPC32XX_CLKPWR_LCDCLK_CTRL);
-#endif
-#ifdef CONFIG_SPI_PL022
+
tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
__raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
LPC32XX_CLKPWR_SSP_CLK_CTRL);
-#endif
- platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs));
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
- struct amba_device *d = amba_devs[i];
- amba_device_register(d, &iomem_resource);
- }
+ tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL);
+ __raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN),
+ LPC32XX_CLKPWR_DMA_CLK_CTRL);
/* Test clock needed for UDA1380 initial init */
__raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
LPC32XX_CLKPWR_TEST_CLK_SEL);
- i2c_register_board_info(0, phy3250_i2c_board_info,
- ARRAY_SIZE(phy3250_i2c_board_info));
+ of_platform_populate(NULL, of_default_bus_match_table,
+ lpc32xx_auxdata_lookup, NULL);
+
+ /* Register GPIOs used on this board */
+ if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
+ printk(KERN_ERR "Error requesting gpio %u",
+ SPI0_CS_GPIO);
+ else if (gpio_direction_output(SPI0_CS_GPIO, 1))
+ printk(KERN_ERR "Error setting gpio %u to output",
+ SPI0_CS_GPIO);
}
static int __init lpc32xx_display_uid(void)
@@ -363,12 +335,17 @@ static int __init lpc32xx_display_uid(vo
}
arch_initcall(lpc32xx_display_uid);
-MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
- /* Maintainer: Kevin Wells, NXP Semiconductors */
+static char const *lpc32xx_dt_compat[] __initdata = {
+ "nxp,lpc32xx",
+ NULL
+};
+
+DT_MACHINE_START(LPC32XX_DT, "LPC32XX SoC (Flattened Device Tree)")
.atag_offset = 0x100,
.map_io = lpc32xx_map_io,
.init_irq = lpc32xx_init_irq,
.timer = &lpc32xx_timer,
- .init_machine = phy3250_board_init,
+ .init_machine = lpc3250_machine_init,
+ .dt_compat = lpc32xx_dt_compat,
.restart = lpc23xx_restart,
MACHINE_END
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v3 10/10] ARM: LPC32xx: Move common code to common.c
2012-04-18 13:36 [PATCH v3 0/10] Second patchset for LPC32xx device tree conversion Roland Stigge
` (8 preceding siblings ...)
2012-04-18 13:36 ` [PATCH v3 9/10] ARM: LPC32xx: Device tree support Roland Stigge
@ 2012-04-18 13:36 ` Roland Stigge
9 siblings, 0 replies; 12+ messages in thread
From: Roland Stigge @ 2012-04-18 13:36 UTC (permalink / raw)
To: arm, linux-arm-kernel, thierry.reding, gregkh, linux-usb,
linux-kernel, linux-input, dmitry.torokhov, axel.lin, broonie,
marek.vasut, devel, kevin.wells, srinivas.bakki, dan.carpenter
Cc: Roland Stigge
This patch moves non-boardspecific LPC32xx code to common.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
---
arch/arm/mach-lpc32xx/common.c | 14 ++++++++++++++
arch/arm/mach-lpc32xx/phy3250.c | 13 -------------
2 files changed, 14 insertions(+), 13 deletions(-)
--- linux-2.6.orig/arch/arm/mach-lpc32xx/common.c
+++ linux-2.6/arch/arm/mach-lpc32xx/common.c
@@ -223,3 +223,17 @@ void lpc23xx_restart(char mode, const ch
while (1)
;
}
+
+static int __init lpc32xx_display_uid(void)
+{
+ u32 uid[4];
+
+ lpc32xx_get_uid(uid);
+
+ printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n",
+ uid[3], uid[2], uid[1], uid[0]);
+
+ return 1;
+}
+arch_initcall(lpc32xx_display_uid);
+
--- linux-2.6.orig/arch/arm/mach-lpc32xx/phy3250.c
+++ linux-2.6/arch/arm/mach-lpc32xx/phy3250.c
@@ -322,19 +322,6 @@ static void __init lpc3250_machine_init(
SPI0_CS_GPIO);
}
-static int __init lpc32xx_display_uid(void)
-{
- u32 uid[4];
-
- lpc32xx_get_uid(uid);
-
- printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n",
- uid[3], uid[2], uid[1], uid[0]);
-
- return 1;
-}
-arch_initcall(lpc32xx_display_uid);
-
static char const *lpc32xx_dt_compat[] __initdata = {
"nxp,lpc32xx",
NULL
^ permalink raw reply [flat|nested] 12+ messages in thread