[ 000/101] 3.6.5-stable review

[ 000/101] 3.6.5-stable review

[Greg Kroah-Hartman]

This is the start of the stable review cycle for the 3.6.5 release.
There are 101 patches in this series, all will be posted as a response
to this one.  If anyone has any issues with these being applied, please
let me know.

Responses should be made by Wed Oct 31 21:31:45 UTC 2012.
Anything received after that time might be too late.

The whole patch series can be found in one patch at:
	kernel.org/pub/linux/kernel/v3.0/stable-review/patch-3.6.5-rc1.gz
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    Linux 3.6.5-rc1

Peng Tao <bergwolf@gmail.com>
    pnfsblock: fix non-aligned DIO write

Peng Tao <bergwolf@gmail.com>
    pnfsblock: fix non-aligned DIO read

Yinghai Lu <yinghai@kernel.org>
    x86, mm: Use memblock memory loop instead of e820_RAM

Olof Johansson <olof@lixom.net>
    x86: efi: Turn off efi_enabled after setup on mixed fw/kernel

Josh Triplett <josh@joshtriplett.org>
    efi: Defer freeing boot services memory until after ACPI init

Stanislaw Gruszka <sgruszka@redhat.com>
    cfg80211/mac80211: avoid state mishmash on deauth

Yinghai Lu <yinghai@kernel.org>
    x86, mm: Undo incorrect revert in arch/x86/mm/init.c

Jacob Shin <jacob.shin@amd.com>
    x86, mm: Find_early_table_space based on ranges that are actually being mapped

Felix Fietkau <nbd@openwrt.org>
    Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"

Andreas Herrmann <andreas.herrmann3@amd.com>
    cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code

Stanislav Yakovlev <stas.yakovlev@gmail.com>
    net/wireless: ipw2200: Fix panic occurring in ipw_handle_promiscuous_tx()

Piotr Haber <phaber@broadcom.com>
    bcma: fix unregistration of cores

Johannes Berg <johannes.berg@intel.com>
    iwlwifi: fix 6000 series channel switch command

Wei Yongjun <yongjun_wei@trendmicro.com.cn>
    dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()

Barry Song <Baohua.Song@csr.com>
    dmaengine: sirf: fix a typo in moving running dma_desc to active queue

Barry Song <Baohua.Song@csr.com>
    dmaengine: sirf: fix a typo in dma_prep_interleaved

Oleg Nesterov <oleg@redhat.com>
    freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD

Dan Williams <dcbw@redhat.com>
    qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan

Johan Hedberg <johan.hedberg@intel.com>
    Bluetooth: SMP: Fix setting unknown auth_req bits

Chris Metcalf <cmetcalf@tilera.com>
    tilegx: fix some issues in the SW TSO support

Larry Finger <Larry.Finger@lwfinger.net>
    b43: Fix oops on unload when firmware not found

Felix Fietkau <nbd@openwrt.org>
    mac80211: use ieee80211_free_txskb in a few more places

Stanislaw Gruszka <sgruszka@redhat.com>
    mac80211: check if key has TKIP type before updating IV

Johannes Berg <johannes.berg@intel.com>
    mac80211: connect with HT20 if HT40 is not permitted

Nicolas Ferre <nicolas.ferre@atmel.com>
    ARM: at91: fix external interrupt specification in board code

Nicolas Ferre <nicolas.ferre@atmel.com>
    ARM: at91: fix external interrupts in non-DT case

Ivan Shugov <ivan.shugov@gmail.com>
    ARM: at91: at91sam9g10: fix SOC type detection

Bo Shen <voice.shen@atmel.com>
    ARM: at91/i2c: change id to let i2c-gpio work

Josh Wu <josh.wu@atmel.com>
    ARM: at91/tc: fix typo in the DT document

Heiko Stuebner <heiko@sntech.de>
    ARM: SAMSUNG: Add naming of s3c64xx-spi devices

Michael S. Tsirkin <mst@redhat.com>
    vhost: fix mergeable bufs on BE hosts

Johan Hovold <jhovold@gmail.com>
    USB: mos7840: remove invalid disconnect handling

Johan Hovold <jhovold@gmail.com>
    USB: mos7840: remove NULL-urb submission

Johan Hovold <jhovold@gmail.com>
    USB: mos7840: fix port-device leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: mos7840: fix urb leak at release

Johan Hovold <jhovold@gmail.com>
    USB: sierra: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: sierra: fix memory leak in probe error path

Johan Hovold <jhovold@gmail.com>
    USB: sierra: fix memory leak in attach error path

Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
    USB: serial: Fix memory leak in sierra_release()

Johan Hovold <jhovold@gmail.com>
    USB: quatech2: fix io after disconnect

Johan Hovold <jhovold@gmail.com>
    USB: quatech2: fix close and disconnect urb handling

Johan Hovold <jhovold@gmail.com>
    USB: quatech2: fix port-data memory leaks

Johan Hovold <jhovold@gmail.com>
    USB: quatech2: fix memory leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: mos7720: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: metro-usb: fix io after disconnect

Johan Hovold <jhovold@gmail.com>
    USB: metro-usb: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: opticon: fix memory leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: opticon: fix DMA from stack

Johan Hovold <jhovold@gmail.com>
    USB: whiteheat: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: whiteheat: fix memory leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: qcserial: fix interface-data memory leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: omninet: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: keyspan: fix NULL-pointer dereferences and memory leaks

Johan Hovold <jhovold@gmail.com>
    USB: option: fix interface-data memory leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: mct_u232: fix broken close

Johan Hovold <jhovold@gmail.com>
    USB: mct_u232: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: ipw: fix interface-data memory leak in error path

Johan Hovold <jhovold@gmail.com>
    USB: digi_acceleport: fix port-data memory leak

Johan Hovold <jhovold@gmail.com>
    USB: ch341: fix port-data memory leak

Octavian Purdila <octavian.purdila@intel.com>
    usb hub: send clear_tt_buffer_complete events when canceling TT clear work

Johan Hovold <jhovold@gmail.com>
    USB: usb-wwan: fix multiple memory leaks in error paths

Michael Shigorin <mike@osdn.org.ua>
    usb-storage: add unusual_devs entry for Casio EX-N1 digital camera

Anisse Astier <anisse@astier.eu>
    ehci: Add yet-another Lucid nohandoff pci quirk

Anisse Astier <anisse@astier.eu>
    ehci: fix Lucid nohandoff pci quirk to be more generic with BIOS versions

K. Y. Srinivasan <kys@microsoft.com>
    Drivers: hv: Cleanup error handling in vmbus_open()

Peter Huewe <peterhuewe@gmx.de>
    extcon: unregister compat link on cleanup

Peter Huewe <peterhuewe@gmx.de>
    extcon: Unregister compat class at module unload to fix oops

Ian Abbott <abbotti@mev.co.uk>
    staging: comedi: amplc_pc236: fix possible NULL deref during detach

Ian Abbott <abbotti@mev.co.uk>
    staging: comedi: amplc_pc236: fix invalid register access during detach

Ian Abbott <abbotti@mev.co.uk>
    staging: comedi: amplc_pc263: fix possible NULL deref during detach

Ian Abbott <abbotti@mev.co.uk>
    staging: comedi: amplc_dio200: fix possible NULL deref during detach

Ian Abbott <abbotti@mev.co.uk>
    staging: comedi: ni_labpc: fix possible NULL deref during detach

Fred Brooks <nsaspook@nsaspook.com>
    staging: comedi: ni_daq_700: fix dio subdevice regression

Ian Abbott <abbotti@mev.co.uk>
    staging: comedi: das08: fix possible NULL deref during detach

Nitin Gupta <ngupta@vflare.org>
    staging: zram: Fix handling of incompressible pages

Arve Hjønnevåg <arve@android.com>
    Staging: android: binder: Allow using highmem for binder buffers

Arve Hjønnevåg <arve@android.com>
    Staging: android: binder: Fix memory leak on thread/process exit

Geert Uytterhoeven <geert@linux-m68k.org>
    sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()

Oliver Neukum <oliver@neukum.org>
    xhci: endianness xhci_calculate_intel_u2_timeout

Oliver Neukum <oliver@neukum.org>
    xhci: fix integer overflow

Sarah Sharp <sarah.a.sharp@linux.intel.com>
    xhci: Fix potential NULL ptr deref in command cancellation.

Trond Myklebust <Trond.Myklebust@netapp.com>
    LOCKD: Clear ln->nsm_clnt only when ln->nsm_users is zero

Trond Myklebust <Trond.Myklebust@netapp.com>
    SUNRPC: Prevent races in xs_abort_connection()

Trond Myklebust <Trond.Myklebust@netapp.com>
    LOCKD: fix races in nsm_client_get

Trond Myklebust <Trond.Myklebust@netapp.com>
    Revert "SUNRPC: Ensure we close the socket on EPIPE errors too..."

Trond Myklebust <Trond.Myklebust@netapp.com>
    SUNRPC: Clear the connect flag when socket state is TCP_CLOSE_WAIT

Trond Myklebust <Trond.Myklebust@netapp.com>
    SUNRPC: Get rid of the xs_error_report socket callback

Jan Kara <jack@suse.cz>
    mm: fix XFS oops due to dirty pages without buffers on s390

Yinghai Lu <yinghai@kernel.org>
    x86, mm: Trim memory in memblock to be page aligned

Dave Young <dyoung@redhat.com>
    Revert "x86/mm: Fix the size calculation of mapping tables"

Jan Beulich <JBeulich@suse.com>
    x86-64: Fix page table accounting

Will Deacon <will.deacon@arm.com>
    ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count

Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
    genalloc: stop crashing the system when destroying a pool

Jan Luebbe <jlu@pengutronix.de>
    drivers/rtc/rtc-imxdi.c: add missing spin lock initialization

Kees Cook <keescook@chromium.org>
    fs/compat_ioctl.c: VIDEO_SET_SPU_PALETTE missing error check

Kees Cook <keescook@chromium.org>
    gen_init_cpio: avoid stack overflow when expanding

Linus Torvalds <torvalds@linux-foundation.org>
    VFS: don't do protected {sym,hard}links by default

Takashi Iwai <tiwai@suse.de>
    ALSA: hda - Fix silent headphone output from Toshiba P200

Stefán Freyr <stefan.freyr@gmail.com>
    ALSA: hda - add dock support for Thinkpad T430

Alex Deucher <alexander.deucher@amd.com>
    drm/radeon: add error output if VM CS fails on cayman

Alex Deucher <alexander.deucher@amd.com>
    drm/radeon: add some new SI PCI ids


-------------

Diffstat:

 .../devicetree/bindings/arm/atmel-at91.txt         |   2 +-
 Makefile                                           |   4 +-
 arch/arm/kernel/smp.c                              |  14 +-
 arch/arm/mach-at91/at91rm9200_devices.c            |   2 +-
 arch/arm/mach-at91/at91sam9260_devices.c           |   2 +-
 arch/arm/mach-at91/at91sam9261_devices.c           |   2 +-
 arch/arm/mach-at91/at91sam9263_devices.c           |   2 +-
 arch/arm/mach-at91/at91sam9rl_devices.c            |   2 +-
 arch/arm/mach-at91/board-neocore926.c              |   2 +-
 arch/arm/mach-at91/board-sam9261ek.c               |   2 +-
 arch/arm/mach-at91/board-sam9263ek.c               |   2 +-
 arch/arm/mach-at91/generic.h                       |   3 +-
 arch/arm/mach-at91/irq.c                           |   9 +-
 arch/arm/mach-at91/setup.c                         |   4 +-
 arch/arm/mach-exynos/common.c                      |   5 +
 arch/arm/mach-s3c24xx/s3c2416.c                    |   2 +
 arch/arm/mach-s3c24xx/s3c2443.c                    |   4 +
 arch/arm/mach-s5p64x0/common.c                     |   3 +
 arch/arm/mach-s5pc100/common.c                     |   3 +
 arch/arm/mach-s5pv210/common.c                     |   3 +
 arch/arm/plat-samsung/include/plat/spi-core.h      |  30 ++++
 arch/x86/include/asm/efi.h                         |   1 +
 arch/x86/kernel/e820.c                             |   3 +
 arch/x86/kernel/setup.c                            |  27 ++-
 arch/x86/mm/init.c                                 |  58 ++++---
 arch/x86/mm/init_64.c                              |   7 +-
 arch/x86/platform/efi/efi.c                        |  43 +++--
 drivers/bcma/main.c                                |   5 +-
 drivers/cpufreq/powernow-k8.c                      |   9 +-
 drivers/dma/imx-dma.c                              |   4 +-
 drivers/dma/sirf-dma.c                             |   4 +-
 drivers/extcon/extcon_class.c                      |   7 +
 drivers/gpu/drm/radeon/evergreen_cs.c              |   1 +
 drivers/hv/channel.c                               |  24 +--
 drivers/net/ethernet/tile/tilegx.c                 |  35 ++--
 drivers/net/usb/cdc_ether.c                        |  41 +++--
 drivers/net/usb/qmi_wwan.c                         |  14 ++
 .../net/wireless/ath/ath9k/ar9003_2p2_initvals.h   | 164 +++++++++---------
 drivers/net/wireless/b43/main.c                    |   4 +
 drivers/net/wireless/ipw2x00/ipw2200.c             |   2 +-
 drivers/net/wireless/iwlwifi/dvm/devices.c         |  39 +++--
 drivers/rtc/rtc-imxdi.c                            |   2 +
 drivers/staging/android/binder.c                   |  30 +++-
 drivers/staging/comedi/drivers/amplc_dio200.c      |   2 +
 drivers/staging/comedi/drivers/amplc_pc236.c       |   6 +-
 drivers/staging/comedi/drivers/amplc_pc263.c       |   3 +
 drivers/staging/comedi/drivers/das08.c             |   2 +
 drivers/staging/comedi/drivers/ni_daq_700.c        |   2 +-
 drivers/staging/comedi/drivers/ni_labpc.c          |   2 +
 drivers/staging/zram/zram_drv.c                    |  12 +-
 drivers/usb/core/hub.c                             |   7 +-
 drivers/usb/host/pci-quirks.c                      |   9 +-
 drivers/usb/host/xhci-ring.c                       |  11 ++
 drivers/usb/host/xhci.c                            |   4 +-
 drivers/usb/serial/ch341.c                         |  23 ++-
 drivers/usb/serial/digi_acceleport.c               | 117 +++++++------
 drivers/usb/serial/ipw.c                           |   7 +-
 drivers/usb/serial/keyspan.c                       | 183 ++++++++++-----------
 drivers/usb/serial/keyspan.h                       |   8 +
 drivers/usb/serial/mct_u232.c                      |  59 ++++---
 drivers/usb/serial/metro-usb.c                     |  65 +++-----
 drivers/usb/serial/mos7720.c                       |  62 +++----
 drivers/usb/serial/mos7840.c                       |  30 +---
 drivers/usb/serial/omninet.c                       |  36 ++--
 drivers/usb/serial/opticon.c                       |  11 +-
 drivers/usb/serial/option.c                        |  23 ++-
 drivers/usb/serial/qcserial.c                      |  33 ++--
 drivers/usb/serial/quatech2.c                      | 135 +++++++--------
 drivers/usb/serial/sierra.c                        | 133 +++++++--------
 drivers/usb/serial/usb-wwan.h                      |   2 +-
 drivers/usb/serial/usb_wwan.c                      | 130 ++++++---------
 drivers/usb/serial/whiteheat.c                     |  60 +++----
 drivers/usb/storage/unusual_devs.h                 |   6 +
 drivers/vhost/net.c                                |   3 +-
 fs/compat_ioctl.c                                  |   2 +
 fs/exec.c                                          |   3 +-
 fs/lockd/mon.c                                     |  57 ++++---
 fs/namei.c                                         |   4 +-
 fs/nfs/blocklayout/blocklayout.c                   |  93 ++++++++---
 fs/sysfs/dir.c                                     |  16 +-
 include/drm/drm_pciids.h                           |   3 +
 include/linux/efi.h                                |   5 +
 include/linux/memblock.h                           |   1 +
 include/net/cfg80211.h                             |   1 +
 init/main.c                                        |   3 +
 lib/genalloc.c                                     |   2 +-
 mm/memblock.c                                      |  24 +++
 mm/rmap.c                                          |  20 ++-
 net/bluetooth/smp.c                                |   6 +-
 net/mac80211/iface.c                               |   2 +-
 net/mac80211/mlme.c                                |  35 ++--
 net/mac80211/sta_info.c                            |   4 +-
 net/mac80211/util.c                                |   4 +-
 net/mac80211/wpa.c                                 |   3 +-
 net/sunrpc/xprtsock.c                              |  41 ++---
 net/wireless/mlme.c                                |  12 +-
 sound/pci/hda/patch_realtek.c                      |  20 ++-
 usr/gen_init_cpio.c                                |  43 ++---
 98 files changed, 1255 insertions(+), 961 deletions(-)

[ 001/101] drm/radeon: add some new SI PCI ids

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Alex Deucher <alexander.deucher@amd.com>

commit b6aa22db7857ab7ed042d6c56b800bfc727cfdff upstream.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 include/drm/drm_pciids.h |    3 +++
 1 file changed, 3 insertions(+)

--- a/include/drm/drm_pciids.h
+++ b/include/drm/drm_pciids.h
@@ -205,6 +205,8 @@
 	{0x1002, 0x6788, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x678A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6790, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x6791, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x6792, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6798, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6799, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x679A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_TAHITI|RADEON_NEW_MEMMAP}, \
@@ -217,6 +219,7 @@
 	{0x1002, 0x6808, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6809, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6810, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x6811, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6816, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6817, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x6818, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_PITCAIRN|RADEON_NEW_MEMMAP}, \

[ 002/101] drm/radeon: add error output if VM CS fails on cayman

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Alex Deucher <alexander.deucher@amd.com>

commit c71721324c612f7f040657ce9917d87f530f9784 upstream.

So we know why the CS was rejected.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/radeon/evergreen_cs.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/gpu/drm/radeon/evergreen_cs.c
+++ b/drivers/gpu/drm/radeon/evergreen_cs.c
@@ -2829,6 +2829,7 @@ static bool evergreen_vm_reg_valid(u32 r
 	case CAYMAN_SQ_EX_ALLOC_TABLE_SLOTS:
 		return true;
 	default:
+		DRM_ERROR("Invalid register 0x%x in CS\n", reg);
 		return false;
 	}
 }

[ 003/101] ALSA: hda - add dock support for Thinkpad T430

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: =?UTF-8?q?Stef=C3=A1n=20Freyr?= <stefan.freyr@gmail.com>

commit 84f98fdf7865fbd35b312eb39ea91e5618c514c7 upstream.

I have a Lenovo ThinkPad T430 and an UltraBase Series 3 docking
station.

Without this patch, if I plug my headphones into the jack on the
computer, everything works fine. The computer speakers mute and the
audio is played in the headphones. However, if I plug into the docking
station headphone jack the computer speakers are muted but there is no
audio in the headphones.

Addresses https://bugs.launchpad.net/bugs/1060372

Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/pci/hda/patch_realtek.c |    1 +
 1 file changed, 1 insertion(+)

--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -6214,6 +6214,7 @@ static const struct snd_pci_quirk alc269
 	SND_PCI_QUIRK(0x17aa, 0x21e9, "Thinkpad Edge 15", ALC269_FIXUP_SKU_IGNORE),
 	SND_PCI_QUIRK(0x17aa, 0x21f6, "Thinkpad T530", ALC269_FIXUP_LENOVO_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x21fa, "Thinkpad X230", ALC269_FIXUP_LENOVO_DOCK),
+	SND_PCI_QUIRK(0x17aa, 0x21f3, "Thinkpad T430", ALC269_FIXUP_LENOVO_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x21fb, "Thinkpad T430s", ALC269_FIXUP_LENOVO_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x2203, "Thinkpad X230 Tablet", ALC269_FIXUP_LENOVO_DOCK),
 	SND_PCI_QUIRK(0x17aa, 0x3bf8, "Quanta FL1", ALC269_FIXUP_PCM_44K),

[ 004/101] ALSA: hda - Fix silent headphone output from Toshiba P200

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <tiwai@suse.de>

commit cb766404e6b8c566569eb9ada02ea45d28729864 upstream.

By some reason, Toshiba laptop doesn't like the EAPD turned up for the
headphone pin.  Add a fix up code to force to turn down EAPD for NID
0x15.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=569991

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/pci/hda/patch_realtek.c |   19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)

--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -5704,6 +5704,7 @@ static const struct hda_verb alc268_beep
 
 enum {
 	ALC268_FIXUP_INV_DMIC,
+	ALC268_FIXUP_HP_EAPD,
 };
 
 static const struct alc_fixup alc268_fixups[] = {
@@ -5711,10 +5712,26 @@ static const struct alc_fixup alc268_fix
 		.type = ALC_FIXUP_FUNC,
 		.v.func = alc_fixup_inv_dmic_0x12,
 	},
+	[ALC268_FIXUP_HP_EAPD] = {
+		.type = ALC_FIXUP_VERBS,
+		.v.verbs = (const struct hda_verb[]) {
+			{0x15, AC_VERB_SET_EAPD_BTLENABLE, 0},
+			{}
+		}
+	},
 };
 
 static const struct alc_model_fixup alc268_fixup_models[] = {
 	{.id = ALC268_FIXUP_INV_DMIC, .name = "inv-dmic"},
+	{.id = ALC268_FIXUP_HP_EAPD, .name = "hp-eapd"},
+	{}
+};
+
+static const struct snd_pci_quirk alc268_fixup_tbl[] = {
+	/* below is codec SSID since multiple Toshiba laptops have the
+	 * same PCI SSID 1179:ff00
+	 */
+	SND_PCI_QUIRK(0x1179, 0xff06, "Toshiba P200", ALC268_FIXUP_HP_EAPD),
 	{}
 };
 
@@ -5749,7 +5766,7 @@ static int patch_alc268(struct hda_codec
 
 	spec = codec->spec;
 
-	alc_pick_fixup(codec, alc268_fixup_models, NULL, alc268_fixups);
+	alc_pick_fixup(codec, alc268_fixup_models, alc268_fixup_tbl, alc268_fixups);
 	alc_apply_fixup(codec, ALC_FIXUP_ACT_PRE_PROBE);
 
 	/* automatic parse from the BIOS config */

[ 005/101] VFS: dont do protected {sym,hard}links by default

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Linus Torvalds <torvalds@linux-foundation.org>

commit 561ec64ae67ef25cac8d72bb9c4bfc955edfd415 upstream.

In commit 800179c9b8a1 ("This adds symlink and hardlink restrictions to
the Linux VFS"), the new link protections were enabled by default, in
the hope that no actual application would care, despite it being
technically against legacy UNIX (and documented POSIX) behavior.

However, it does turn out to break some applications.  It's rare, and
it's unfortunate, but it's unacceptable to break existing systems, so
we'll have to default to legacy behavior.

In particular, it has broken the way AFD distributes files, see

  http://www.dwd.de/AFD/

along with some legacy scripts.

Distributions can end up setting this at initrd time or in system
scripts: if you have security problems due to link attacks during your
early boot sequence, you have bigger problems than some kernel sysctl
setting. Do:

	echo 1 > /proc/sys/fs/protected_symlinks
	echo 1 > /proc/sys/fs/protected_hardlinks

to re-enable the link protections.

Alternatively, we may at some point introduce a kernel config option
that sets these kinds of "more secure but not traditional" behavioural
options automatically.

Reported-by: Nick Bowler <nbowler@elliptictech.com>
Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/namei.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/fs/namei.c
+++ b/fs/namei.c
@@ -651,8 +651,8 @@ static inline void put_link(struct namei
 	path_put(link);
 }
 
-int sysctl_protected_symlinks __read_mostly = 1;
-int sysctl_protected_hardlinks __read_mostly = 1;
+int sysctl_protected_symlinks __read_mostly = 0;
+int sysctl_protected_hardlinks __read_mostly = 0;
 
 /**
  * may_follow_link - Check symlink following for unsafe situations

[ 006/101] gen_init_cpio: avoid stack overflow when expanding

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Kees Cook <keescook@chromium.org>

commit 20f1de659b77364d55d4e7fad2ef657e7730323f upstream.

Fix possible overflow of the buffer used for expanding environment
variables when building file list.

In the extremely unlikely case of an attacker having control over the
environment variables visible to gen_init_cpio, control over the
contents of the file gen_init_cpio parses, and gen_init_cpio was built
without compiler hardening, the attacker can gain arbitrary execution
control via a stack buffer overflow.

  $ cat usr/crash.list
  file foo ${BIG}${BIG}${BIG}${BIG}${BIG}${BIG} 0755 0 0
  $ BIG=$(perl -e 'print "A" x 4096;') ./usr/gen_init_cpio usr/crash.list
  *** buffer overflow detected ***: ./usr/gen_init_cpio terminated

This also replaces the space-indenting with tabs.

Patch based on existing fix extracted from grsecurity.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 usr/gen_init_cpio.c |   41 ++++++++++++++++++++++-------------------
 1 file changed, 22 insertions(+), 19 deletions(-)

--- a/usr/gen_init_cpio.c
+++ b/usr/gen_init_cpio.c
@@ -303,7 +303,7 @@ static int cpio_mkfile(const char *name,
 	int retval;
 	int rc = -1;
 	int namesize;
-	int i;
+	unsigned int i;
 
 	mode |= S_IFREG;
 
@@ -381,25 +381,28 @@ error:
 
 static char *cpio_replace_env(char *new_location)
 {
-       char expanded[PATH_MAX + 1];
-       char env_var[PATH_MAX + 1];
-       char *start;
-       char *end;
-
-       for (start = NULL; (start = strstr(new_location, "${")); ) {
-               end = strchr(start, '}');
-               if (start < end) {
-                       *env_var = *expanded = '\0';
-                       strncat(env_var, start + 2, end - start - 2);
-                       strncat(expanded, new_location, start - new_location);
-                       strncat(expanded, getenv(env_var), PATH_MAX);
-                       strncat(expanded, end + 1, PATH_MAX);
-                       strncpy(new_location, expanded, PATH_MAX);
-               } else
-                       break;
-       }
+	char expanded[PATH_MAX + 1];
+	char env_var[PATH_MAX + 1];
+	char *start;
+	char *end;
+
+	for (start = NULL; (start = strstr(new_location, "${")); ) {
+		end = strchr(start, '}');
+		if (start < end) {
+			*env_var = *expanded = '\0';
+			strncat(env_var, start + 2, end - start - 2);
+			strncat(expanded, new_location, start - new_location);
+			strncat(expanded, getenv(env_var),
+				PATH_MAX - strlen(expanded));
+			strncat(expanded, end + 1,
+				PATH_MAX - strlen(expanded));
+			strncpy(new_location, expanded, PATH_MAX);
+			new_location[PATH_MAX] = 0;
+		} else
+			break;
+	}
 
-       return new_location;
+	return new_location;
 }
 
 

[ 007/101] fs/compat_ioctl.c: VIDEO_SET_SPU_PALETTE missing error check

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Kees Cook <keescook@chromium.org>

commit 12176503366885edd542389eed3aaf94be163fdb upstream.

The compat ioctl for VIDEO_SET_SPU_PALETTE was missing an error check
while converting ioctl arguments.  This could lead to leaking kernel
stack contents into userspace.

Patch extracted from existing fix in grsecurity.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/compat_ioctl.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/fs/compat_ioctl.c
+++ b/fs/compat_ioctl.c
@@ -210,6 +210,8 @@ static int do_video_set_spu_palette(unsi
 
 	err  = get_user(palp, &up->palette);
 	err |= get_user(length, &up->length);
+	if (err)
+		return -EFAULT;
 
 	up_native = compat_alloc_user_space(sizeof(struct video_spu_palette));
 	err  = put_user(compat_ptr(palp), &up_native->palette);

[ 008/101] drivers/rtc/rtc-imxdi.c: add missing spin lock initialization

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Jan Luebbe <jlu@pengutronix.de>

commit fee0de7791f967c2c5f0d43eb7b7261761b45e64 upstream.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Roland Stigge <stigge@antcom.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/rtc/rtc-imxdi.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/rtc/rtc-imxdi.c
+++ b/drivers/rtc/rtc-imxdi.c
@@ -392,6 +392,8 @@ static int dryice_rtc_probe(struct platf
 	if (imxdi->ioaddr == NULL)
 		return -ENOMEM;
 
+	spin_lock_init(&imxdi->irq_lock);
+
 	imxdi->irq = platform_get_irq(pdev, 0);
 	if (imxdi->irq < 0)
 		return imxdi->irq;

[ 009/101] genalloc: stop crashing the system when destroying a pool

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>

commit eedce141cd2dad8d0cefc5468ef41898949a7031 upstream.

The genalloc code uses the bitmap API from include/linux/bitmap.h and
lib/bitmap.c, which is based on long values.  Both bitmap_set from
lib/bitmap.c and bitmap_set_ll, which is the lockless version from
genalloc.c, use BITMAP_LAST_WORD_MASK to set the first bits in a long in
the bitmap.

That one uses (1 << bits) - 1, 0b111, if you are setting the first three
bits.  This means that the API counts from the least significant bits
(LSB from now on) to the MSB.  The LSB in the first long is bit 0, then.
The same works for the lookup functions.

The genalloc code uses longs for the bitmap, as it should.  In
include/linux/genalloc.h, struct gen_pool_chunk has unsigned long
bits[0] as its last member.  When allocating the struct, genalloc should
reserve enough space for the bitmap.  This should be a proper number of
longs that can fit the amount of bits in the bitmap.

However, genalloc allocates an integer number of bytes that fit the
amount of bits, but may not be an integer amount of longs.  9 bytes, for
example, could be allocated for 70 bits.

This is a problem in itself if the Least Significat Bit in a long is in
the byte with the largest address, which happens in Big Endian machines.
This means genalloc is not allocating the byte in which it will try to
set or check for a bit.

This may end up in memory corruption, where genalloc will try to set the
bits it has not allocated.  In fact, genalloc may not set these bits
because it may find them already set, because they were not zeroed since
they were not allocated.  And that's what causes a BUG when
gen_pool_destroy is called and check for any set bits.

What really happens is that genalloc uses kmalloc_node with __GFP_ZERO
on gen_pool_add_virt.  With SLAB and SLUB, this means the whole slab
will be cleared, not only the requested bytes.  Since struct
gen_pool_chunk has a size that is a multiple of 8, and slab sizes are
multiples of 8, we get lucky and allocate and clear the right amount of
bytes.

Hower, this is not the case with SLOB or with older code that did memset
after allocating instead of using __GFP_ZERO.

So, a simple module as this (running 3.6.0), will cause a crash when
rmmod'ed.

  [root@phantom-lp2 foo]# cat foo.c
  #include <linux/kernel.h>
  #include <linux/module.h>
  #include <linux/init.h>
  #include <linux/genalloc.h>

  MODULE_LICENSE("GPL");
  MODULE_VERSION("0.1");

  static struct gen_pool *foo_pool;

  static __init int foo_init(void)
  {
          int ret;
          foo_pool = gen_pool_create(10, -1);
          if (!foo_pool)
                  return -ENOMEM;
          ret = gen_pool_add(foo_pool, 0xa0000000, 32 << 10, -1);
          if (ret) {
                  gen_pool_destroy(foo_pool);
                  return ret;
          }
          return 0;
  }

  static __exit void foo_exit(void)
  {
          gen_pool_destroy(foo_pool);
  }

  module_init(foo_init);
  module_exit(foo_exit);
  [root@phantom-lp2 foo]# zcat /proc/config.gz | grep SLOB
  CONFIG_SLOB=y
  [root@phantom-lp2 foo]# insmod ./foo.ko
  [root@phantom-lp2 foo]# rmmod foo
  ------------[ cut here ]------------
  kernel BUG at lib/genalloc.c:243!
  cpu 0x4: Vector: 700 (Program Check) at [c0000000bb0e7960]
      pc: c0000000003cb50c: .gen_pool_destroy+0xac/0x110
      lr: c0000000003cb4fc: .gen_pool_destroy+0x9c/0x110
      sp: c0000000bb0e7be0
     msr: 8000000000029032
    current = 0xc0000000bb0e0000
    paca    = 0xc000000006d30e00   softe: 0        irq_happened: 0x01
      pid   = 13044, comm = rmmod
  kernel BUG at lib/genalloc.c:243!
  [c0000000bb0e7ca0] d000000004b00020 .foo_exit+0x20/0x38 [foo]
  [c0000000bb0e7d20] c0000000000dff98 .SyS_delete_module+0x1a8/0x290
  [c0000000bb0e7e30] c0000000000097d4 syscall_exit+0x0/0x94
  --- Exception: c00 (System Call) at 000000800753d1a0
  SP (fffd0b0e640) is in userspace

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Benjamin Gaignard <benjamin.gaignard@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 lib/genalloc.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/lib/genalloc.c
+++ b/lib/genalloc.c
@@ -176,7 +176,7 @@ int gen_pool_add_virt(struct gen_pool *p
 	struct gen_pool_chunk *chunk;
 	int nbits = size >> pool->min_alloc_order;
 	int nbytes = sizeof(struct gen_pool_chunk) +
-				(nbits + BITS_PER_BYTE - 1) / BITS_PER_BYTE;
+				BITS_TO_LONGS(nbits) * sizeof(long);
 
 	chunk = kmalloc_node(nbytes, GFP_KERNEL | __GFP_ZERO, nid);
 	if (unlikely(chunk == NULL))

[ 010/101] ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Will Deacon <will.deacon@arm.com>

commit 5f40b909728ad784eb43aa309d3c4e9bdf050781 upstream.

When booting a secondary CPU, the primary CPU hands two sets of page
tables via the secondary_data struct:

	(1) swapper_pg_dir: a normal, cacheable, shared (if SMP) mapping
	    of the kernel image (i.e. the tables used by init_mm).

	(2) idmap_pgd: an uncached mapping of the .idmap.text ELF
	    section.

The idmap is generally used when enabling and disabling the MMU, which
includes early CPU boot. In this case, the secondary CPU switches to
swapper as soon as it enters C code:

	struct mm_struct *mm = &init_mm;
	unsigned int cpu = smp_processor_id();

	/*
	 * All kernel threads share the same mm context; grab a
	 * reference and switch to it.
	 */
	atomic_inc(&mm->mm_count);
	current->active_mm = mm;
	cpumask_set_cpu(cpu, mm_cpumask(mm));
	cpu_switch_mm(mm->pgd, mm);

This causes a problem on ARMv7, where the identity mapping is treated as
strongly-ordered leading to architecturally UNPREDICTABLE behaviour of
exclusive accesses, such as those used by atomic_inc.

This patch re-orders the secondary_start_kernel function so that we
switch to swapper before performing any exclusive accesses.

Reported-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Cc: David McKay <david.mckay@st.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/kernel/smp.c |   14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

--- a/arch/arm/kernel/smp.c
+++ b/arch/arm/kernel/smp.c
@@ -222,18 +222,24 @@ static void percpu_timer_setup(void);
 asmlinkage void __cpuinit secondary_start_kernel(void)
 {
 	struct mm_struct *mm = &init_mm;
-	unsigned int cpu = smp_processor_id();
+	unsigned int cpu;
+
+	/*
+	 * The identity mapping is uncached (strongly ordered), so
+	 * switch away from it before attempting any exclusive accesses.
+	 */
+	cpu_switch_mm(mm->pgd, mm);
+	enter_lazy_tlb(mm, current);
+	local_flush_tlb_all();
 
 	/*
 	 * All kernel threads share the same mm context; grab a
 	 * reference and switch to it.
 	 */
+	cpu = smp_processor_id();
 	atomic_inc(&mm->mm_count);
 	current->active_mm = mm;
 	cpumask_set_cpu(cpu, mm_cpumask(mm));
-	cpu_switch_mm(mm->pgd, mm);
-	enter_lazy_tlb(mm, current);
-	local_flush_tlb_all();
 
 	printk("CPU%u: Booted secondary processor\n", cpu);
 

[ 011/101] x86-64: Fix page table accounting

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Jan Beulich <JBeulich@suse.com>

commit 876ee61aadf01aa0db981b5d249cbdd53dc28b5e upstream.

Commit 20167d3421a089a1bf1bd680b150dc69c9506810 ("x86-64: Fix
accounting in kernel_physical_mapping_init()") went a little too
far by entirely removing the counting of pre-populated page
tables: this should be done at boot time (to cover the page
tables set up in early boot code), but shouldn't be done during
memory hot add.

Hence, re-add the removed increments of "pages", but make them
and the one in phys_pte_init() conditional upon !after_bootmem.

Reported-Acked-and-Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/506DAFBA020000780009FA8C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/mm/init_64.c |    7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

--- a/arch/x86/mm/init_64.c
+++ b/arch/x86/mm/init_64.c
@@ -386,7 +386,8 @@ phys_pte_init(pte_t *pte_page, unsigned
 		 * these mappings are more intelligent.
 		 */
 		if (pte_val(*pte)) {
-			pages++;
+			if (!after_bootmem)
+				pages++;
 			continue;
 		}
 
@@ -451,6 +452,8 @@ phys_pmd_init(pmd_t *pmd_page, unsigned
 			 * attributes.
 			 */
 			if (page_size_mask & (1 << PG_LEVEL_2M)) {
+				if (!after_bootmem)
+					pages++;
 				last_map_addr = next;
 				continue;
 			}
@@ -526,6 +529,8 @@ phys_pud_init(pud_t *pud_page, unsigned
 			 * attributes.
 			 */
 			if (page_size_mask & (1 << PG_LEVEL_1G)) {
+				if (!after_bootmem)
+					pages++;
 				last_map_addr = next;
 				continue;
 			}

[ 012/101] Revert "x86/mm: Fix the size calculation of mapping tables"

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Dave Young <dyoung@redhat.com>

commit 7b16bbf97375d9fb7fc107b3f80afeb94a204e44 upstream.

Commit:

   722bc6b16771 x86/mm: Fix the size calculation of mapping tables

Tried to address the issue that the first 2/4M should use 4k pages
if PSE enabled, but extra counts should only be valid for x86_32.

This commit caused a kdump regression: the kdump kernel hangs.

Work is in progress to fundamentally fix the various page table
initialization issues that we have, via the design suggested
by H. Peter Anvin, but it's not ready yet to be merged.

So, to get a working kdump revert to the last known working version,
which is the revert of this commit and of a followup fix (which was
incomplete):

   bd2753b2dda7 x86/mm: Only add extra pages count for the first memory range during pre-allocation

Tested kdump on physical and virtual machines.

Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Tested-by: Flavio Leitner <fbl@redhat.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Flavio Leitner <fbl@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: ianfang.cn@gmail.com
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/mm/init.c |   22 +++++++++-------------
 1 file changed, 9 insertions(+), 13 deletions(-)

--- a/arch/x86/mm/init.c
+++ b/arch/x86/mm/init.c
@@ -29,14 +29,8 @@ int direct_gbpages
 #endif
 ;
 
-struct map_range {
-	unsigned long start;
-	unsigned long end;
-	unsigned page_size_mask;
-};
-
-static void __init find_early_table_space(struct map_range *mr, unsigned long end,
-					  int use_pse, int use_gbpages)
+static void __init find_early_table_space(unsigned long end, int use_pse,
+					  int use_gbpages)
 {
 	unsigned long puds, pmds, ptes, tables, start = 0, good_end = end;
 	phys_addr_t base;
@@ -61,10 +55,6 @@ static void __init find_early_table_spac
 #ifdef CONFIG_X86_32
 		extra += PMD_SIZE;
 #endif
-		/* The first 2/4M doesn't use large pages. */
-		if (mr->start < PMD_SIZE)
-			extra += mr->end - mr->start;
-
 		ptes = (extra + PAGE_SIZE - 1) >> PAGE_SHIFT;
 	} else
 		ptes = (end + PAGE_SIZE - 1) >> PAGE_SHIFT;
@@ -95,6 +85,12 @@ void __init native_pagetable_reserve(u64
 	memblock_reserve(start, end - start);
 }
 
+struct map_range {
+	unsigned long start;
+	unsigned long end;
+	unsigned page_size_mask;
+};
+
 #ifdef CONFIG_X86_32
 #define NR_RANGE_MR 3
 #else /* CONFIG_X86_64 */
@@ -267,7 +263,7 @@ unsigned long __init_refok init_memory_m
 	 * nodes are discovered.
 	 */
 	if (!after_bootmem)
-		find_early_table_space(&mr[0], end, use_pse, use_gbpages);
+		find_early_table_space(end, use_pse, use_gbpages);
 
 	for (i = 0; i < nr_range; i++)
 		ret = kernel_physical_mapping_init(mr[i].start, mr[i].end,

[ 013/101] x86, mm: Trim memory in memblock to be page aligned

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Yinghai Lu <yinghai@kernel.org>

commit 6ede1fd3cb404c0016de6ac529df46d561bd558b upstream.

We will not map partial pages, so need to make sure memblock
allocation will not allocate those bytes out.

Also we will use for_each_mem_pfn_range() to loop to map memory
range to keep them consistent.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/kernel/e820.c   |    3 +++
 include/linux/memblock.h |    1 +
 mm/memblock.c            |   24 ++++++++++++++++++++++++
 3 files changed, 28 insertions(+)

--- a/arch/x86/kernel/e820.c
+++ b/arch/x86/kernel/e820.c
@@ -1077,6 +1077,9 @@ void __init memblock_x86_fill(void)
 		memblock_add(ei->addr, ei->size);
 	}
 
+	/* throw away partial pages */
+	memblock_trim_memory(PAGE_SIZE);
+
 	memblock_dump_all();
 }
 
--- a/include/linux/memblock.h
+++ b/include/linux/memblock.h
@@ -57,6 +57,7 @@ int memblock_add(phys_addr_t base, phys_
 int memblock_remove(phys_addr_t base, phys_addr_t size);
 int memblock_free(phys_addr_t base, phys_addr_t size);
 int memblock_reserve(phys_addr_t base, phys_addr_t size);
+void memblock_trim_memory(phys_addr_t align);
 
 #ifdef CONFIG_HAVE_MEMBLOCK_NODE_MAP
 void __next_mem_pfn_range(int *idx, int nid, unsigned long *out_start_pfn,
--- a/mm/memblock.c
+++ b/mm/memblock.c
@@ -929,6 +929,30 @@ int __init_memblock memblock_is_region_r
 	return memblock_overlaps_region(&memblock.reserved, base, size) >= 0;
 }
 
+void __init_memblock memblock_trim_memory(phys_addr_t align)
+{
+	int i;
+	phys_addr_t start, end, orig_start, orig_end;
+	struct memblock_type *mem = &memblock.memory;
+
+	for (i = 0; i < mem->cnt; i++) {
+		orig_start = mem->regions[i].base;
+		orig_end = mem->regions[i].base + mem->regions[i].size;
+		start = round_up(orig_start, align);
+		end = round_down(orig_end, align);
+
+		if (start == orig_start && end == orig_end)
+			continue;
+
+		if (start < end) {
+			mem->regions[i].base = start;
+			mem->regions[i].size = end - start;
+		} else {
+			memblock_remove_region(mem, i);
+			i--;
+		}
+	}
+}
 
 void __init_memblock memblock_set_current_limit(phys_addr_t limit)
 {

[ 014/101] mm: fix XFS oops due to dirty pages without buffers on s390

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Jan Kara <jack@suse.cz>

commit ef5d437f71afdf4afdbab99213add99f4b1318fd upstream.

On s390 any write to a page (even from kernel itself) sets architecture
specific page dirty bit.  Thus when a page is written to via buffered
write, HW dirty bit gets set and when we later map and unmap the page,
page_remove_rmap() finds the dirty bit and calls set_page_dirty().

Dirtying of a page which shouldn't be dirty can cause all sorts of
problems to filesystems.  The bug we observed in practice is that
buffers from the page get freed, so when the page gets later marked as
dirty and writeback writes it, XFS crashes due to an assertion
BUG_ON(!PagePrivate(page)) in page_buffers() called from
xfs_count_page_state().

Similar problem can also happen when zero_user_segment() call from
xfs_vm_writepage() (or block_write_full_page() for that matter) set the
hardware dirty bit during writeback, later buffers get freed, and then
page unmapped.

Fix the issue by ignoring s390 HW dirty bit for page cache pages of
mappings with mapping_cap_account_dirty().  This is safe because for
such mappings when a page gets marked as writeable in PTE it is also
marked dirty in do_wp_page() or do_page_fault().  When the dirty bit is
cleared by clear_page_dirty_for_io(), the page gets writeprotected in
page_mkclean().  So pagecache page is writeable if and only if it is
dirty.

Thanks to Hugh Dickins for pointing out mapping has to have
mapping_cap_account_dirty() for things to work and proposing a cleaned
up variant of the patch.

The patch has survived about two hours of running fsx-linux on tmpfs
while heavily swapping and several days of running on out build machines
where the original problem was triggered.

Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 mm/rmap.c |   20 +++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

--- a/mm/rmap.c
+++ b/mm/rmap.c
@@ -56,6 +56,7 @@
 #include <linux/mmu_notifier.h>
 #include <linux/migrate.h>
 #include <linux/hugetlb.h>
+#include <linux/backing-dev.h>
 
 #include <asm/tlbflush.h>
 
@@ -971,11 +972,8 @@ int page_mkclean(struct page *page)
 
 	if (page_mapped(page)) {
 		struct address_space *mapping = page_mapping(page);
-		if (mapping) {
+		if (mapping)
 			ret = page_mkclean_file(mapping, page);
-			if (page_test_and_clear_dirty(page_to_pfn(page), 1))
-				ret = 1;
-		}
 	}
 
 	return ret;
@@ -1161,6 +1159,7 @@ void page_add_file_rmap(struct page *pag
  */
 void page_remove_rmap(struct page *page)
 {
+	struct address_space *mapping = page_mapping(page);
 	bool anon = PageAnon(page);
 	bool locked;
 	unsigned long flags;
@@ -1183,8 +1182,19 @@ void page_remove_rmap(struct page *page)
 	 * this if the page is anon, so about to be freed; but perhaps
 	 * not if it's in swapcache - there might be another pte slot
 	 * containing the swap entry, but page not yet written to swap.
+	 *
+	 * And we can skip it on file pages, so long as the filesystem
+	 * participates in dirty tracking; but need to catch shm and tmpfs
+	 * and ramfs pages which have been modified since creation by read
+	 * fault.
+	 *
+	 * Note that mapping must be decided above, before decrementing
+	 * mapcount (which luckily provides a barrier): once page is unmapped,
+	 * it could be truncated and page->mapping reset to NULL at any moment.
+	 * Note also that we are relying on page_mapping(page) to set mapping
+	 * to &swapper_space when PageSwapCache(page).
 	 */
-	if ((!anon || PageSwapCache(page)) &&
+	if (mapping && !mapping_cap_account_dirty(mapping) &&
 	    page_test_and_clear_dirty(page_to_pfn(page), 1))
 		set_page_dirty(page);
 	/*

[ 015/101] SUNRPC: Get rid of the xs_error_report socket callback

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <Trond.Myklebust@netapp.com>

commit f878b657ce8e7d3673afe48110ec208a29e38c4a upstream.

Chris Perl reports that we're seeing races between the wakeup call in
xs_error_report and the connect attempts. Basically, Chris has shown
that in certain circumstances, the call to xs_error_report causes the
rpc_task that is responsible for reconnecting to wake up early, thus
triggering a disconnect and retry.

Since the sk->sk_error_report() calls in the socket layer are always
followed by a tcp_done() in the cases where we care about waking up
the rpc_tasks, just let the state_change callbacks take responsibility
for those wake ups.

Reported-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/sunrpc/xprtsock.c |   25 -------------------------
 1 file changed, 25 deletions(-)

--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -254,7 +254,6 @@ struct sock_xprt {
 	void			(*old_data_ready)(struct sock *, int);
 	void			(*old_state_change)(struct sock *);
 	void			(*old_write_space)(struct sock *);
-	void			(*old_error_report)(struct sock *);
 };
 
 /*
@@ -781,7 +780,6 @@ static void xs_save_old_callbacks(struct
 	transport->old_data_ready = sk->sk_data_ready;
 	transport->old_state_change = sk->sk_state_change;
 	transport->old_write_space = sk->sk_write_space;
-	transport->old_error_report = sk->sk_error_report;
 }
 
 static void xs_restore_old_callbacks(struct sock_xprt *transport, struct sock *sk)
@@ -789,7 +787,6 @@ static void xs_restore_old_callbacks(str
 	sk->sk_data_ready = transport->old_data_ready;
 	sk->sk_state_change = transport->old_state_change;
 	sk->sk_write_space = transport->old_write_space;
-	sk->sk_error_report = transport->old_error_report;
 }
 
 static void xs_reset_transport(struct sock_xprt *transport)
@@ -1549,25 +1546,6 @@ static void xs_tcp_state_change(struct s
 	read_unlock_bh(&sk->sk_callback_lock);
 }
 
-/**
- * xs_error_report - callback mainly for catching socket errors
- * @sk: socket
- */
-static void xs_error_report(struct sock *sk)
-{
-	struct rpc_xprt *xprt;
-
-	read_lock_bh(&sk->sk_callback_lock);
-	if (!(xprt = xprt_from_sock(sk)))
-		goto out;
-	dprintk("RPC:       %s client %p...\n"
-			"RPC:       error %d\n",
-			__func__, xprt, sk->sk_err);
-	xprt_wake_pending_tasks(xprt, -EAGAIN);
-out:
-	read_unlock_bh(&sk->sk_callback_lock);
-}
-
 static void xs_write_space(struct sock *sk)
 {
 	struct socket *sock;
@@ -1867,7 +1845,6 @@ static int xs_local_finish_connecting(st
 		sk->sk_user_data = xprt;
 		sk->sk_data_ready = xs_local_data_ready;
 		sk->sk_write_space = xs_udp_write_space;
-		sk->sk_error_report = xs_error_report;
 		sk->sk_allocation = GFP_ATOMIC;
 
 		xprt_clear_connected(xprt);
@@ -1995,7 +1972,6 @@ static void xs_udp_finish_connecting(str
 		sk->sk_user_data = xprt;
 		sk->sk_data_ready = xs_udp_data_ready;
 		sk->sk_write_space = xs_udp_write_space;
-		sk->sk_error_report = xs_error_report;
 		sk->sk_no_check = UDP_CSUM_NORCV;
 		sk->sk_allocation = GFP_ATOMIC;
 
@@ -2113,7 +2089,6 @@ static int xs_tcp_finish_connecting(stru
 		sk->sk_data_ready = xs_tcp_data_ready;
 		sk->sk_state_change = xs_tcp_state_change;
 		sk->sk_write_space = xs_tcp_write_space;
-		sk->sk_error_report = xs_error_report;
 		sk->sk_allocation = GFP_ATOMIC;
 
 		/* socket options */

[ 016/101] SUNRPC: Clear the connect flag when socket state is TCP_CLOSE_WAIT

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <Trond.Myklebust@netapp.com>

commit d0bea455dd48da1ecbd04fedf00eb89437455fdc upstream.

This is needed to ensure that we call xprt_connect() upon the next
call to call_connect().

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/sunrpc/xprtsock.c |    1 +
 1 file changed, 1 insertion(+)

--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -1522,6 +1522,7 @@ static void xs_tcp_state_change(struct s
 	case TCP_CLOSE_WAIT:
 		/* The server initiated a shutdown of the socket */
 		xprt->connect_cookie++;
+		clear_bit(XPRT_CONNECTED, &xprt->state);
 		xs_tcp_force_close(xprt);
 	case TCP_CLOSING:
 		/*

[ 017/101] Revert "SUNRPC: Ensure we close the socket on EPIPE errors too..."

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <Trond.Myklebust@netapp.com>

commit b9d2bb2ee537424a7f855e1f93eed44eb9ee0854 upstream.

This reverts commit 55420c24a0d4d1fce70ca713f84aa00b6b74a70e.
Now that we clear the connected flag when entering TCP_CLOSE_WAIT,
the deadlock described in this commit is no longer possible.
Instead, the resulting call to xs_tcp_shutdown() can interfere
with pending reconnection attempts.

Reported-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/sunrpc/xprtsock.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -736,10 +736,10 @@ static int xs_tcp_send_request(struct rp
 		dprintk("RPC:       sendmsg returned unrecognized error %d\n",
 			-status);
 	case -ECONNRESET:
-	case -EPIPE:
 		xs_tcp_shutdown(xprt);
 	case -ECONNREFUSED:
 	case -ENOTCONN:
+	case -EPIPE:
 		clear_bit(SOCK_ASYNC_NOSPACE, &transport->sock->flags);
 	}
 

[ 018/101] LOCKD: fix races in nsm_client_get

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <Trond.Myklebust@netapp.com>

commit a4ee8d978e47e79d536226dccb48991f70091168 upstream.

Commit e9406db20fecbfcab646bad157b4cfdc7cadddfb (lockd: per-net
NSM client creation and destruction helpers introduced) contains
a nasty race on initialisation of the per-net NSM client because
it doesn't check whether or not the client is set after grabbing
the nsm_create_mutex.

Reported-by: Nix <nix@esperi.org.uk>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/lockd/mon.c |   43 ++++++++++++++++++++++++++-----------------
 1 file changed, 26 insertions(+), 17 deletions(-)

--- a/fs/lockd/mon.c
+++ b/fs/lockd/mon.c
@@ -85,29 +85,38 @@ static struct rpc_clnt *nsm_create(struc
 	return rpc_create(&args);
 }
 
+static struct rpc_clnt *nsm_client_set(struct lockd_net *ln,
+		struct rpc_clnt *clnt)
+{
+	spin_lock(&ln->nsm_clnt_lock);
+	if (ln->nsm_users == 0) {
+		if (clnt == NULL)
+			goto out;
+		ln->nsm_clnt = clnt;
+	}
+	clnt = ln->nsm_clnt;
+	ln->nsm_users++;
+out:
+	spin_unlock(&ln->nsm_clnt_lock);
+	return clnt;
+}
+
 static struct rpc_clnt *nsm_client_get(struct net *net)
 {
-	static DEFINE_MUTEX(nsm_create_mutex);
-	struct rpc_clnt	*clnt;
+	struct rpc_clnt	*clnt, *new;
 	struct lockd_net *ln = net_generic(net, lockd_net_id);
 
-	spin_lock(&ln->nsm_clnt_lock);
-	if (ln->nsm_users) {
-		ln->nsm_users++;
-		clnt = ln->nsm_clnt;
-		spin_unlock(&ln->nsm_clnt_lock);
+	clnt = nsm_client_set(ln, NULL);
+	if (clnt != NULL)
 		goto out;
-	}
-	spin_unlock(&ln->nsm_clnt_lock);
 
-	mutex_lock(&nsm_create_mutex);
-	clnt = nsm_create(net);
-	if (!IS_ERR(clnt)) {
-		ln->nsm_clnt = clnt;
-		smp_wmb();
-		ln->nsm_users = 1;
-	}
-	mutex_unlock(&nsm_create_mutex);
+	clnt = new = nsm_create(net);
+	if (IS_ERR(clnt))
+		goto out;
+
+	clnt = nsm_client_set(ln, new);
+	if (clnt != new)
+		rpc_shutdown_client(new);
 out:
 	return clnt;
 }

[ 019/101] SUNRPC: Prevent races in xs_abort_connection()

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <Trond.Myklebust@netapp.com>

commit 4bc1e68ed6a8b59be8a79eb719be515a55c7bc68 upstream.

The call to xprt_disconnect_done() that is triggered by a successful
connection reset will trigger another automatic wakeup of all tasks
on the xprt->pending rpc_wait_queue. In particular it will cause an
early wake up of the task that called xprt_connect().

All we really want to do here is clear all the socket-specific state
flags, so we split that functionality out of xs_sock_mark_closed()
into a helper that can be called by xs_abort_connection()

Reported-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Chris Perl <chris.perl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/sunrpc/xprtsock.c |   13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -1459,7 +1459,7 @@ static void xs_tcp_cancel_linger_timeout
 	xprt_clear_connecting(xprt);
 }
 
-static void xs_sock_mark_closed(struct rpc_xprt *xprt)
+static void xs_sock_reset_connection_flags(struct rpc_xprt *xprt)
 {
 	smp_mb__before_clear_bit();
 	clear_bit(XPRT_CONNECTION_ABORT, &xprt->state);
@@ -1467,6 +1467,11 @@ static void xs_sock_mark_closed(struct r
 	clear_bit(XPRT_CLOSE_WAIT, &xprt->state);
 	clear_bit(XPRT_CLOSING, &xprt->state);
 	smp_mb__after_clear_bit();
+}
+
+static void xs_sock_mark_closed(struct rpc_xprt *xprt)
+{
+	xs_sock_reset_connection_flags(xprt);
 	/* Mark transport as closed and wake up all pending tasks */
 	xprt_disconnect_done(xprt);
 }
@@ -2042,10 +2047,8 @@ static void xs_abort_connection(struct s
 	any.sa_family = AF_UNSPEC;
 	result = kernel_connect(transport->sock, &any, sizeof(any), 0);
 	if (!result)
-		xs_sock_mark_closed(&transport->xprt);
-	else
-		dprintk("RPC:       AF_UNSPEC connect return code %d\n",
-				result);
+		xs_sock_reset_connection_flags(&transport->xprt);
+	dprintk("RPC:       AF_UNSPEC connect return code %d\n", result);
 }
 
 static void xs_tcp_reuse_connection(struct sock_xprt *transport)

[ 020/101] LOCKD: Clear ln->nsm_clnt only when ln->nsm_users is zero

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Trond Myklebust <Trond.Myklebust@netapp.com>

commit e498daa81295d02f7359af313c2b7f87e1062207 upstream.

The current code is clearing it in all cases _except_ when zero.

Reported-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/lockd/mon.c |   14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

--- a/fs/lockd/mon.c
+++ b/fs/lockd/mon.c
@@ -124,18 +124,16 @@ out:
 static void nsm_client_put(struct net *net)
 {
 	struct lockd_net *ln = net_generic(net, lockd_net_id);
-	struct rpc_clnt	*clnt = ln->nsm_clnt;
-	int shutdown = 0;
+	struct rpc_clnt	*clnt = NULL;
 
 	spin_lock(&ln->nsm_clnt_lock);
-	if (ln->nsm_users) {
-		if (--ln->nsm_users)
-			ln->nsm_clnt = NULL;
-		shutdown = !ln->nsm_users;
+	ln->nsm_users--;
+	if (ln->nsm_users == 0) {
+		clnt = ln->nsm_clnt;
+		ln->nsm_clnt = NULL;
 	}
 	spin_unlock(&ln->nsm_clnt_lock);
-
-	if (shutdown)
+	if (clnt != NULL)
 		rpc_shutdown_client(clnt);
 }
 

[ 021/101] xhci: Fix potential NULL ptr deref in command cancellation.

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Sarah Sharp <sarah.a.sharp@linux.intel.com>

commit 43a09f7fb01fa1e091416a2aa49b6c666458c1ee upstream.

The command cancellation code doesn't check whether find_trb_seg()
couldn't find the segment that contains the TRB to be canceled.  This
could cause a NULL pointer deference later in the function when next_trb
is called.  It's unlikely to happen unless something is wrong with the
command ring pointers, so add some debugging in case it happens.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit b63f4053cc8aa22a98e3f9a97845afe6c15d0a0d "xHCI:
handle command after aborting the command ring".

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/xhci-ring.c |   11 +++++++++++
 1 file changed, 11 insertions(+)

--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1228,6 +1228,17 @@ static void xhci_cmd_to_noop(struct xhci
 	cur_seg = find_trb_seg(xhci->cmd_ring->first_seg,
 			xhci->cmd_ring->dequeue, &cycle_state);
 
+	if (!cur_seg) {
+		xhci_warn(xhci, "Command ring mismatch, dequeue = %p %llx (dma)\n",
+				xhci->cmd_ring->dequeue,
+				(unsigned long long)
+				xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
+					xhci->cmd_ring->dequeue));
+		xhci_debug_ring(xhci, xhci->cmd_ring);
+		xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
+		return;
+	}
+
 	/* find the command trb matched by cd from command ring */
 	for (cmd_trb = xhci->cmd_ring->dequeue;
 			cmd_trb != xhci->cmd_ring->enqueue;

[ 022/101] xhci: fix integer overflow

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Oliver Neukum <oliver@neukum.org>

commit 16b45fdf9c4e82f5d3bc53aa70737650e7c8d5ed upstream.

xhci_service_interval_to_ns() returns long long
to avoid an overflow. However, the type cast happens
too late. The fix is to force ULL from the beginning.

This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c15a7a8e2f992a5f7c7683453ca406d82 "xhci: Add Intel
U1/U2 timeout policy."

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/xhci.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -4020,7 +4020,7 @@ int xhci_update_device(struct usb_hcd *h
 static unsigned long long xhci_service_interval_to_ns(
 		struct usb_endpoint_descriptor *desc)
 {
-	return (1 << (desc->bInterval - 1)) * 125 * 1000;
+	return (1ULL << (desc->bInterval - 1)) * 125 * 1000;
 }
 
 static u16 xhci_get_timeout_no_hub_lpm(struct usb_device *udev,

[ 023/101] xhci: endianness xhci_calculate_intel_u2_timeout

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Oliver Neukum <oliver@neukum.org>

commit 966e7a854177097083683176ced871558b631a12 upstream.

An le16 is accessed without conversion.

This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c15a7a8e2f992a5f7c7683453ca406d82 "xhci: Add Intel
U1/U2 timeout policy."

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/xhci.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -4141,7 +4141,7 @@ static u16 xhci_calculate_intel_u2_timeo
 			(xhci_service_interval_to_ns(desc) > timeout_ns))
 		timeout_ns = xhci_service_interval_to_ns(desc);
 
-	u2_del_ns = udev->bos->ss_cap->bU2DevExitLat * 1000;
+	u2_del_ns = le16_to_cpu(udev->bos->ss_cap->bU2DevExitLat) * 1000ULL;
 	if (u2_del_ns > timeout_ns)
 		timeout_ns = u2_del_ns;
 

[ 024/101] sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Geert Uytterhoeven <geert@linux-m68k.org>

commit 66081a72517a131430dcf986775f3268aafcb546 upstream.

The warning check for duplicate sysfs entries can cause a buffer overflow
when printing the warning, as strcat() doesn't check buffer sizes.
Use strlcat() instead.

Since strlcat() doesn't return a pointer to the passed buffer, unlike
strcat(), I had to convert the nested concatenation in sysfs_add_one() to
an admittedly more obscure comma operator construct, to avoid emitting code
for the concatenation if CONFIG_BUG is disabled.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/sysfs/dir.c |   16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

--- a/fs/sysfs/dir.c
+++ b/fs/sysfs/dir.c
@@ -485,20 +485,18 @@ int __sysfs_add_one(struct sysfs_addrm_c
 /**
  *	sysfs_pathname - return full path to sysfs dirent
  *	@sd: sysfs_dirent whose path we want
- *	@path: caller allocated buffer
+ *	@path: caller allocated buffer of size PATH_MAX
  *
  *	Gives the name "/" to the sysfs_root entry; any path returned
  *	is relative to wherever sysfs is mounted.
- *
- *	XXX: does no error checking on @path size
  */
 static char *sysfs_pathname(struct sysfs_dirent *sd, char *path)
 {
 	if (sd->s_parent) {
 		sysfs_pathname(sd->s_parent, path);
-		strcat(path, "/");
+		strlcat(path, "/", PATH_MAX);
 	}
-	strcat(path, sd->s_name);
+	strlcat(path, sd->s_name, PATH_MAX);
 	return path;
 }
 
@@ -531,9 +529,11 @@ int sysfs_add_one(struct sysfs_addrm_cxt
 		char *path = kzalloc(PATH_MAX, GFP_KERNEL);
 		WARN(1, KERN_WARNING
 		     "sysfs: cannot create duplicate filename '%s'\n",
-		     (path == NULL) ? sd->s_name :
-		     strcat(strcat(sysfs_pathname(acxt->parent_sd, path), "/"),
-		            sd->s_name));
+		     (path == NULL) ? sd->s_name
+				    : (sysfs_pathname(acxt->parent_sd, path),
+				       strlcat(path, "/", PATH_MAX),
+				       strlcat(path, sd->s_name, PATH_MAX),
+				       path));
 		kfree(path);
 	}
 

[ 025/101] Staging: android: binder: Fix memory leak on thread/process exit

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Arve Hjønnevåg <arve@android.com>

commit 675d66b0ed5fd170d6a44cf8dbb3fa56a5347bdb upstream.

If a thread or process exited while a reply, one-way transaction or
death notification was pending, the struct holding the pending work
was leaked.

Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/android/binder.c |   28 +++++++++++++++++++++++++++-
 1 file changed, 27 insertions(+), 1 deletion(-)

--- a/drivers/staging/android/binder.c
+++ b/drivers/staging/android/binder.c
@@ -2507,14 +2507,38 @@ static void binder_release_work(struct l
 			struct binder_transaction *t;
 
 			t = container_of(w, struct binder_transaction, work);
-			if (t->buffer->target_node && !(t->flags & TF_ONE_WAY))
+			if (t->buffer->target_node &&
+			    !(t->flags & TF_ONE_WAY)) {
 				binder_send_failed_reply(t, BR_DEAD_REPLY);
+			} else {
+				binder_debug(BINDER_DEBUG_DEAD_TRANSACTION,
+					"binder: undelivered transaction %d\n",
+					t->debug_id);
+				t->buffer->transaction = NULL;
+				kfree(t);
+				binder_stats_deleted(BINDER_STAT_TRANSACTION);
+			}
 		} break;
 		case BINDER_WORK_TRANSACTION_COMPLETE: {
+			binder_debug(BINDER_DEBUG_DEAD_TRANSACTION,
+				"binder: undelivered TRANSACTION_COMPLETE\n");
 			kfree(w);
 			binder_stats_deleted(BINDER_STAT_TRANSACTION_COMPLETE);
 		} break;
+		case BINDER_WORK_DEAD_BINDER_AND_CLEAR:
+		case BINDER_WORK_CLEAR_DEATH_NOTIFICATION: {
+			struct binder_ref_death *death;
+
+			death = container_of(w, struct binder_ref_death, work);
+			binder_debug(BINDER_DEBUG_DEAD_TRANSACTION,
+				"binder: undelivered death notification, %p\n",
+				death->cookie);
+			kfree(death);
+			binder_stats_deleted(BINDER_STAT_DEATH);
+		} break;
 		default:
+			pr_err("binder: unexpected work type, %d, not freed\n",
+			       w->type);
 			break;
 		}
 	}
@@ -2984,6 +3008,7 @@ static void binder_deferred_release(stru
 		nodes++;
 		rb_erase(&node->rb_node, &proc->nodes);
 		list_del_init(&node->work.entry);
+		binder_release_work(&node->async_todo);
 		if (hlist_empty(&node->refs)) {
 			kfree(node);
 			binder_stats_deleted(BINDER_STAT_NODE);
@@ -3022,6 +3047,7 @@ static void binder_deferred_release(stru
 		binder_delete_ref(ref);
 	}
 	binder_release_work(&proc->todo);
+	binder_release_work(&proc->delivered_death);
 	buffers = 0;
 
 	while ((n = rb_first(&proc->allocated_buffers))) {

[ 026/101] Staging: android: binder: Allow using highmem for binder buffers

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Arve Hjønnevåg <arve@android.com>

commit 585650dcec88e704a19bb226a34b6a7166111623 upstream.

The default kernel mapping for the pages allocated for the binder
buffers is never used. Set the __GFP_HIGHMEM flag when allocating
these pages so we don't needlessly use low memory pages that may
be required elsewhere.

Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/android/binder.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/staging/android/binder.c
+++ b/drivers/staging/android/binder.c
@@ -655,7 +655,7 @@ static int binder_update_page_range(stru
 		page = &proc->pages[(page_addr - proc->buffer) / PAGE_SIZE];
 
 		BUG_ON(*page);
-		*page = alloc_page(GFP_KERNEL | __GFP_ZERO);
+		*page = alloc_page(GFP_KERNEL | __GFP_HIGHMEM | __GFP_ZERO);
 		if (*page == NULL) {
 			pr_err("binder: %d: binder_alloc_buf failed "
 			       "for page at %p\n", proc->pid, page_addr);

[ 027/101] staging: zram: Fix handling of incompressible pages

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Nitin Gupta <ngupta@vflare.org>

commit c8f2f0db1d0294aaf37e8a85bea9bbc4aaf5c0fe upstream.

Change 130f315a (staging: zram: remove special handle of uncompressed page)
introduced a bug in the handling of incompressible pages which resulted in
memory allocation failure for such pages.

When a page expands on compression, say from 4K to 4K+30, we were trying to
do zsmalloc(pool, 4K+30). However, the maximum size which zsmalloc can
allocate is PAGE_SIZE (for obvious reasons), so such allocation requests
always return failure (0).

For a page that has compressed size larger than the original size (this may
happen with already compressed or random data), there is no point storing
the compressed version as that would take more space and would also require
time for decompression when needed again. So, the fix is to store any page,
whose compressed size exceeds a threshold (max_zpage_size), as-it-is i.e.
without compression.  Memory required for storing this uncompressed page can
then be requested from zsmalloc which supports PAGE_SIZE sized allocations.

Lastly, the fix checks that we do not attempt to "decompress" the page which
we stored in the uncompressed form -- we just memcpy() out such pages.

Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Reported-by: viechweg@gmail.com
Reported-by: paerley@gmail.com
Reported-by: wu.tommy@gmail.com
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/zram/zram_drv.c |   12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

--- a/drivers/staging/zram/zram_drv.c
+++ b/drivers/staging/zram/zram_drv.c
@@ -223,8 +223,13 @@ static int zram_bvec_read(struct zram *z
 	cmem = zs_map_object(zram->mem_pool, zram->table[index].handle,
 				ZS_MM_RO);
 
-	ret = lzo1x_decompress_safe(cmem, zram->table[index].size,
+	if (zram->table[index].size == PAGE_SIZE) {
+		memcpy(uncmem, cmem, PAGE_SIZE);
+		ret = LZO_E_OK;
+	} else {
+		ret = lzo1x_decompress_safe(cmem, zram->table[index].size,
 				    uncmem, &clen);
+	}
 
 	if (is_partial_io(bvec)) {
 		memcpy(user_mem + bvec->bv_offset, uncmem + offset,
@@ -342,8 +347,11 @@ static int zram_bvec_write(struct zram *
 		goto out;
 	}
 
-	if (unlikely(clen > max_zpage_size))
+	if (unlikely(clen > max_zpage_size)) {
 		zram_stat_inc(&zram->stats.bad_compress);
+		src = uncmem;
+		clen = PAGE_SIZE;
+	}
 
 	handle = zs_malloc(zram->mem_pool, clen);
 	if (!handle) {

[ 028/101] staging: comedi: das08: fix possible NULL deref during detach

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Abbott <abbotti@mev.co.uk>

commit ee280d134f2e05e0172369a53fbe202dbfc527fa upstream.

`das08_detach()` is called by the comedi core to clean up if either
`das08_attach()` or `das08_attach_pci()` returns an error.  It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  This is a valid assumption if `das08_attach()` fails, but not
if `das08_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `das08_detach()` and return early if it
is `NULL`.  This is okay because the only other thing that could have
been allocated is `dev->private` and that is freed by the comedi core,
not by this function.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/das08.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/staging/comedi/drivers/das08.c
+++ b/drivers/staging/comedi/drivers/das08.c
@@ -1028,6 +1028,8 @@ static void __maybe_unused das08_detach(
 	const struct das08_board_struct *thisboard = comedi_board(dev);
 	struct das08_private_struct *devpriv = dev->private;
 
+	if (!thisboard)
+		return;
 	das08_common_detach(dev);
 	if (IS_ENABLED(CONFIG_COMEDI_DAS08_ISA) &&
 	    (thisboard->bustype == isa || thisboard->bustype == pc104)) {

[ 029/101] staging: comedi: ni_daq_700: fix dio subdevice regression

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Fred Brooks <nsaspook@nsaspook.com>

commit 6681e63399926651cc29bcb9d92229b6f1cf1daa upstream.

Here is a small patch to fix a problem caused by a previous patch that
removed the  callback function.  The callback remove patch:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1de02225358988e8fd48d1dc3fd12336bbae258a

I finally booted my dev machine on the latest kernel (running Debian
here so it's still on 3.2 normally) to test the ni_daq_700 driver with
my test program and noticed this bug.

Shift the DIO_R read result to bits 8..15 Digital direction
configuration: channels 0-7 output, 8-15 input (8225 device emu as port
A output, port B input, port C N/A).

Signed-off-by: Fred Brooks <nsaspook@nsaspook.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/ni_daq_700.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/staging/comedi/drivers/ni_daq_700.c
+++ b/drivers/staging/comedi/drivers/ni_daq_700.c
@@ -71,7 +71,7 @@ static int subdev_700_insn(struct comedi
 	}
 
 	data[1] = s->state & 0xff;
-	data[1] |= inb(dev->iobase + DIO_R);
+	data[1] |= inb(dev->iobase + DIO_R) << 8;
 
 	return insn->n;
 }

[ 030/101] staging: comedi: ni_labpc: fix possible NULL deref during detach

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Abbott <abbotti@mev.co.uk>

commit 922b67c1ac53014d80649a961a2fde700cd065d8 upstream.

`labpc_common_detach()` is called by the comedi core to clean up if
either `labpc_attach()` (including the one in the "ni_labpc_cs" module)
or `labpc_attach_pci()` returns an error.  It assumes the `thisboard`
macro (expanding to `((struct labpc_board_struct *)dev->board_ptr)`) is
non-null.  This is a valid assumption if `labpc_attach()` fails, but not
if `labpc_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `labpc_common_detach()` and return early
if it is `NULL`.  This is okay because the only other thing that could
have been allocated is `dev->private` and that is freed by the comedi
core, not by this function.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/ni_labpc.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/staging/comedi/drivers/ni_labpc.c
+++ b/drivers/staging/comedi/drivers/ni_labpc.c
@@ -809,6 +809,8 @@ static int labpc_find_device(struct come
 
 void labpc_common_detach(struct comedi_device *dev)
 {
+	if (!thisboard)
+		return;
 	if (dev->subdevices)
 		subdev_8255_cleanup(dev, dev->subdevices + 2);
 #ifdef CONFIG_ISA_DMA_API

[ 031/101] staging: comedi: amplc_dio200: fix possible NULL deref during detach

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Abbott <abbotti@mev.co.uk>

commit dfb2540e91e1f63765bc3ff497ad0b714d774261 upstream.

`dio200_detach()` is called by the comedi core to clean up if either
`dio200_attach()` or `dio200_attach_pci()` return an error.  It assigns
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  In the case of a previous call to `dio200_attach()` it won't
be `NULL` because the comedi core will have pointed it to one of the
elements of `dio200_boards[]`, but in the case of a previous call to
`dio200_attach_pci()` it could be `NULL`, leading to a null pointer
dereference.

Check that `thisboard` is valid at the top of `dio200_detach()` and
return early if it is `NULL`.  This is okay because the only other thing
that could have been allocated is `dev->private` and that is freed by
the comedi core, not by this function.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/amplc_dio200.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/staging/comedi/drivers/amplc_dio200.c
+++ b/drivers/staging/comedi/drivers/amplc_dio200.c
@@ -1429,6 +1429,8 @@ static void dio200_detach(struct comedi_
 	const struct dio200_layout_struct *layout;
 	unsigned n;
 
+	if (!thisboard)
+		return;
 	if (dev->irq)
 		free_irq(dev->irq, dev);
 	if (dev->subdevices) {

[ 032/101] staging: comedi: amplc_pc263: fix possible NULL deref during detach

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Abbott <abbotti@mev.co.uk>

commit 1d1171ffda585c1cab7bd7cf4bd8f8fd5923fb4a upstream.

`pc263_detach()` is called by the comedi core to clean up if either
`pc263_attach()` or `pc263_attach_pci()` returns an error.  It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  This is a valid assumption if `pc263_attach()` fails, but not
if `pc263_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `pc263_detach()` and return early if it
is `NULL`.  This is okay because no other resources need cleaning up in
this case.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/amplc_pc263.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/staging/comedi/drivers/amplc_pc263.c
+++ b/drivers/staging/comedi/drivers/amplc_pc263.c
@@ -310,8 +310,11 @@ static int __devinit pc263_attach_pci(st
 
 static void pc263_detach(struct comedi_device *dev)
 {
+	const struct pc263_board *thisboard = comedi_board(dev);
 	struct pci_dev *pcidev = comedi_to_pci_dev(dev);
 
+	if (!thisboard)
+		return;
 	if (pcidev) {
 		if (dev->iobase)
 			comedi_pci_disable(pcidev);

[ 033/101] staging: comedi: amplc_pc236: fix invalid register access during detach

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Abbott <abbotti@mev.co.uk>

commit aaeb61a97b7159ebe30b18a422d04eeabfa8790b upstream.

`pc236_detach()` is called by the comedi core if it attempted to attach
a device and failed.  `pc236_detach()` calls `pc236_intr_disable()` if
the comedi device private data pointer (`devpriv`) is non-null.  This
test is insufficient as `pc236_intr_disable()` accesses hardware
registers and the attach routine may have failed before it has saved
their I/O base addresses.

Fix it by checking `dev->iobase` is non-zero before calling
`pc236_intr_disable()` as that means the I/O base addresses have been
saved and the hardware registers can be accessed.  It also implies the
comedi device private data pointer is valid, so there is no need to
check it.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/amplc_pc236.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

--- a/drivers/staging/comedi/drivers/amplc_pc236.c
+++ b/drivers/staging/comedi/drivers/amplc_pc236.c
@@ -577,10 +577,9 @@ static int __devinit pc236_attach_pci(st
 
 static void pc236_detach(struct comedi_device *dev)
 {
-	struct pc236_private *devpriv = dev->private;
 	struct pci_dev *pcidev = comedi_to_pci_dev(dev);
 
-	if (devpriv)
+	if (dev->iobase)
 		pc236_intr_disable(dev);
 	if (dev->irq)
 		free_irq(dev->irq, dev);

[ 034/101] staging: comedi: amplc_pc236: fix possible NULL deref during detach

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Abbott <abbotti@mev.co.uk>

commit 2db012bd40b889d8e5483d3daa07af04c4c109d8 upstream.

`pc236_detach()` is called by the comedi core to clean up if either
`pc236_attach()` or `pc236_attach_pci()` returns an error.  It sets
`thisboard` to the return value of `comedi_board(dev)` and assumes it is
non-null.  This is a valid assumption if `pc236_attach()` fails, but not
if `pc236_attach_pci()` fails, leading to a possible NULL pointer
dereference.

Check `thisboard` at the top of `pc236_detach()` and return early if it
is `NULL`.  This is okay because the only other thing that could have
been allocated is `dev->private` and that is freed by the comedi core,
not by this function.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/staging/comedi/drivers/amplc_pc236.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/staging/comedi/drivers/amplc_pc236.c
+++ b/drivers/staging/comedi/drivers/amplc_pc236.c
@@ -577,8 +577,11 @@ static int __devinit pc236_attach_pci(st
 
 static void pc236_detach(struct comedi_device *dev)
 {
+	const struct pc236_board *thisboard = comedi_board(dev);
 	struct pci_dev *pcidev = comedi_to_pci_dev(dev);
 
+	if (!thisboard)
+		return;
 	if (dev->iobase)
 		pc236_intr_disable(dev);
 	if (dev->irq)

[ 035/101] extcon: Unregister compat class at module unload to fix oops

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Peter Huewe <peterhuewe@gmx.de>

commit 0dc77b6dabec8fd298392018cc0de5214af2dc43 upstream.

If you compile extcon with CONFIG_ANDROID and then load and unload the
module you get a simple oops as the driver does not unregister its
compat class and thus cannot register it again.

Full trace:

root@(none):~# modprobe extcon_class
root@(none):~# rmmod extcon_class
root@(none):~# modprobe extcon_class
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0xde/0x100()
sysfs: cannot create duplicate filename '/class/switch'
Modules linked in: extcon_class(+) [last unloaded: extcon_class]
Call Trace:
9f451a00:  [<602a58bc>] printk+0x0/0xa8
9f451a18:  [<60039b43>] warn_slowpath_common+0x93/0xd0
9f451a28:  [<6012c6de>] sysfs_add_one+0xde/0x100
9f451a50:  [<601d3d90>] strcat+0x0/0x40
9f451a68:  [<60039cdc>] warn_slowpath_fmt+0x9c/0xa0
9f451a90:  [<6002fe32>] unblock_signals+0x0/0x84
9f451ab0:  [<60039c40>] warn_slowpath_fmt+0x0/0xa0
9f451ac0:  [<6002fe32>] unblock_signals+0x0/0x84
9f451ae8:  [<6012bd97>] sysfs_pathname.isra.10+0x57/0x70
9f451b00:  [<601d3d90>] strcat+0x0/0x40
9f451b18:  [<6012bd97>] sysfs_pathname.isra.10+0x57/0x70
9f451b48:  [<6012c6de>] sysfs_add_one+0xde/0x100
9f451b78:  [<6012c96f>] create_dir+0x8f/0x100
9f451bc0:  [<a0861000>] extcon_class_init+0x0/0x12 [extcon_class]
9f451bd8:  [<6012cda6>] sysfs_create_dir+0xa6/0x1c0
9f451be8:  [<601d89f1>] kvasprintf+0x81/0xa0
9f451bf8:  [<601cf0f0>] kobject_get+0x0/0x50
9f451c18:  [<601cf396>] kobject_add_internal+0x96/0x280
9f451c60:  [<a0861000>] extcon_class_init+0x0/0x12 [extcon_class]
9f451c78:  [<601cfb93>] kobject_add+0xd3/0x140
9f451cc0:  [<601cfac0>] kobject_add+0x0/0x140
9f451cd0:  [<6002fe32>] unblock_signals+0x0/0x84
9f451cf8:  [<6002fffc>] set_signals+0x29/0x3f
9f451d28:  [<600c1de1>] kmem_cache_alloc+0xe1/0x100
9f451d78:  [<601cffa0>] kobject_create_and_add+0x50/0xa0
9f451da8:  [<601fbe76>] class_compat_register+0x56/0x80
9f451dc8:  [<a085d118>] create_extcon_class+0x88/0xd0 [extcon_class]
9f451de8:  [<a0861010>] extcon_class_init+0x10/0x12 [extcon_class]
9f451df8:  [<600189a8>] do_one_initcall+0x48/0x1f0
9f451e20:  [<60061920>] blocking_notifier_call_chain+0x0/0x20
9f451e30:  [<60061920>] blocking_notifier_call_chain+0x0/0x20
9f451e58:  [<6007e3c3>] sys_init_module+0xa3/0x280
9f451e88:  [<6001e2ad>] handle_syscall+0x8d/0x90
9f451ea8:  [<60033370>] userspace+0x405/0x531
9f451ee8:  [<6001e380>] copy_chunk_to_user+0x0/0x40
9f451ef8:  [<6001e5cd>] do_op_one_page+0x14d/0x220
9f451fd8:  [<6001a355>] fork_handler+0x95/0xa0

---[ end trace dd512cc03fe1c367 ]---
------------[ cut here ]------------
WARNING: at lib/kobject.c:196 kobject_add_internal+0x26e/0x280()
kobject_add_internal failed for switch with -EEXIST, don't try to
register things with the same name in the same directory.
Modules linked in: extcon_class(+) [last unloaded: extcon_class]
Call Trace:
9f451ad0:  [<602a58bc>] printk+0x0/0xa8
9f451ae8:  [<60039b43>] warn_slowpath_common+0x93/0xd0
9f451af8:  [<601cf56e>] kobject_add_internal+0x26e/0x280
9f451b18:  [<601cf140>] kobject_put+0x0/0x70
9f451b20:  [<a0861000>] extcon_class_init+0x0/0x12 [extcon_class]
9f451b38:  [<60039cdc>] warn_slowpath_fmt+0x9c/0xa0
9f451b88:  [<60039c40>] warn_slowpath_fmt+0x0/0xa0
9f451bc0:  [<a0861000>] extcon_class_init+0x0/0x12 [extcon_class]
9f451bd8:  [<6012cda6>] sysfs_create_dir+0xa6/0x1c0
9f451be8:  [<601d89f1>] kvasprintf+0x81/0xa0
9f451bf8:  [<601cf0f0>] kobject_get+0x0/0x50
9f451c18:  [<601cf56e>] kobject_add_internal+0x26e/0x280
9f451c60:  [<a0861000>] extcon_class_init+0x0/0x12 [extcon_class]
9f451c78:  [<601cfb93>] kobject_add+0xd3/0x140
9f451cc0:  [<601cfac0>] kobject_add+0x0/0x140
9f451cd0:  [<6002fe32>] unblock_signals+0x0/0x84
9f451cf8:  [<6002fffc>] set_signals+0x29/0x3f
9f451d28:  [<600c1de1>] kmem_cache_alloc+0xe1/0x100
9f451d78:  [<601cffa0>] kobject_create_and_add+0x50/0xa0
9f451da8:  [<601fbe76>] class_compat_register+0x56/0x80
9f451dc8:  [<a085d118>] create_extcon_class+0x88/0xd0 [extcon_class]
9f451de8:  [<a0861010>] extcon_class_init+0x10/0x12 [extcon_class]
9f451df8:  [<600189a8>] do_one_initcall+0x48/0x1f0
9f451e20:  [<60061920>] blocking_notifier_call_chain+0x0/0x20
9f451e30:  [<60061920>] blocking_notifier_call_chain+0x0/0x20
9f451e58:  [<6007e3c3>] sys_init_module+0xa3/0x280
9f451e88:  [<6001e2ad>] handle_syscall+0x8d/0x90
9f451ea8:  [<60033370>] userspace+0x405/0x531
9f451ee8:  [<6001e380>] copy_chunk_to_user+0x0/0x40
9f451ef8:  [<6001e5cd>] do_op_one_page+0x14d/0x220
9f451fd8:  [<6001a355>] fork_handler+0x95/0xa0

---[ end trace dd512cc03fe1c368 ]---
kobject_create_and_add: kobject_add error: -17
------------[ cut here ]------------
WARNING: at drivers/extcon/extcon_class.c:545
create_extcon_class+0xbc/0xd0 [extcon_class]()
cannot allocate
Modules linked in: extcon_class(+) [last unloaded: extcon_class]
Call Trace:
9f451c80:  [<602a58bc>] printk+0x0/0xa8
9f451c98:  [<60039b43>] warn_slowpath_common+0x93/0xd0
9f451ca0:  [<6002fe32>] unblock_signals+0x0/0x84
9f451ca8:  [<a085d14c>] create_extcon_class+0xbc/0xd0 [extcon_class]
9f451cd0:  [<a0861000>] extcon_class_init+0x0/0x12 [extcon_class]
9f451ce8:  [<60039cdc>] warn_slowpath_fmt+0x9c/0xa0
9f451d20:  [<6002fe32>] unblock_signals+0x0/0x84
9f451d28:  [<60039c40>] warn_slowpath_fmt+0x0/0xa0
9f451d48:  [<6002fffc>] set_signals+0x29/0x3f
9f451d58:  [<601cf172>] kobject_put+0x32/0x70
9f451d78:  [<600c22c3>] kfree+0xb3/0x100
9f451da8:  [<601fbe9a>] class_compat_register+0x7a/0x80
9f451dc8:  [<a085d14c>] create_extcon_class+0xbc/0xd0 [extcon_class]
9f451de8:  [<a0861010>] extcon_class_init+0x10/0x12 [extcon_class]
9f451df8:  [<600189a8>] do_one_initcall+0x48/0x1f0
9f451e20:  [<60061920>] blocking_notifier_call_chain+0x0/0x20
9f451e30:  [<60061920>] blocking_notifier_call_chain+0x0/0x20
9f451e58:  [<6007e3c3>] sys_init_module+0xa3/0x280
9f451e88:  [<6001e2ad>] handle_syscall+0x8d/0x90
9f451ea8:  [<60033370>] userspace+0x405/0x531
9f451ee8:  [<6001e380>] copy_chunk_to_user+0x0/0x40
9f451ef8:  [<6001e5cd>] do_op_one_page+0x14d/0x220
9f451fd8:  [<6001a355>] fork_handler+0x95/0xa0

---[ end trace dd512cc03fe1c369 ]---
FATAL: Error inserting extcon_class
(/lib/modules/3.6.0-rc6-00178-g811315f/kernel/drivers/extcon/extcon_class.ko):
Cannot allocate memory

This patch fixes this.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/extcon/extcon_class.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/extcon/extcon_class.c
+++ b/drivers/extcon/extcon_class.c
@@ -821,6 +821,9 @@ module_init(extcon_class_init);
 
 static void __exit extcon_class_exit(void)
 {
+#if defined(CONFIG_ANDROID)
+	class_compat_unregister(switch_class);
+#endif
 	class_destroy(extcon_class);
 }
 module_exit(extcon_class_exit);

[ 036/101] extcon: unregister compat link on cleanup

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Peter Huewe <peterhuewe@gmx.de>

commit 824a1bc045cef278aec15bef35d8d0b59ce77856 upstream.

Since extcon registers this compat link at device registration
(extcon_dev_register), we should probably remove them at deregistration/cleanup.

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

---
 drivers/extcon/extcon_class.c |    4 ++++
 1 file changed, 4 insertions(+)

--- a/drivers/extcon/extcon_class.c
+++ b/drivers/extcon/extcon_class.c
@@ -575,6 +575,10 @@ static void extcon_cleanup(struct extcon
 			kfree(edev->cables);
 		}
 
+#if defined(CONFIG_ANDROID)
+		if (switch_class)
+			class_compat_remove_link(switch_class, edev->dev, NULL);
+#endif
 		device_unregister(edev->dev);
 		put_device(edev->dev);
 	}

[ 037/101] Drivers: hv: Cleanup error handling in vmbus_open()

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: "K. Y. Srinivasan" <kys@microsoft.com>

commit 1392550240aaa72ce3a094a38bd23525cd67ce60 upstream.

Fix a memory leak  in the error handling path in the function vmbus_open().

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/hv/channel.c |   24 +++++++++++++-----------
 1 file changed, 13 insertions(+), 11 deletions(-)

--- a/drivers/hv/channel.c
+++ b/drivers/hv/channel.c
@@ -146,14 +146,14 @@ int vmbus_open(struct vmbus_channel *new
 
 	if (ret != 0) {
 		err = ret;
-		goto errorout;
+		goto error0;
 	}
 
 	ret = hv_ringbuffer_init(
 		&newchannel->inbound, in, recv_ringbuffer_size);
 	if (ret != 0) {
 		err = ret;
-		goto errorout;
+		goto error0;
 	}
 
 
@@ -168,7 +168,7 @@ int vmbus_open(struct vmbus_channel *new
 
 	if (ret != 0) {
 		err = ret;
-		goto errorout;
+		goto error0;
 	}
 
 	/* Create and init the channel open message */
@@ -177,7 +177,7 @@ int vmbus_open(struct vmbus_channel *new
 			   GFP_KERNEL);
 	if (!open_info) {
 		err = -ENOMEM;
-		goto errorout;
+		goto error0;
 	}
 
 	init_completion(&open_info->waitevent);
@@ -193,7 +193,7 @@ int vmbus_open(struct vmbus_channel *new
 
 	if (userdatalen > MAX_USER_DEFINED_BYTES) {
 		err = -EINVAL;
-		goto errorout;
+		goto error0;
 	}
 
 	if (userdatalen)
@@ -208,19 +208,18 @@ int vmbus_open(struct vmbus_channel *new
 			       sizeof(struct vmbus_channel_open_channel));
 
 	if (ret != 0)
-		goto cleanup;
+		goto error1;
 
 	t = wait_for_completion_timeout(&open_info->waitevent, 5*HZ);
 	if (t == 0) {
 		err = -ETIMEDOUT;
-		goto errorout;
+		goto error1;
 	}
 
 
 	if (open_info->response.open_result.status)
 		err = open_info->response.open_result.status;
 
-cleanup:
 	spin_lock_irqsave(&vmbus_connection.channelmsg_lock, flags);
 	list_del(&open_info->msglistentry);
 	spin_unlock_irqrestore(&vmbus_connection.channelmsg_lock, flags);
@@ -228,9 +227,12 @@ cleanup:
 	kfree(open_info);
 	return err;
 
-errorout:
-	hv_ringbuffer_cleanup(&newchannel->outbound);
-	hv_ringbuffer_cleanup(&newchannel->inbound);
+error1:
+	spin_lock_irqsave(&vmbus_connection.channelmsg_lock, flags);
+	list_del(&open_info->msglistentry);
+	spin_unlock_irqrestore(&vmbus_connection.channelmsg_lock, flags);
+
+error0:
 	free_pages((unsigned long)out,
 		get_order(send_ringbuffer_size + recv_ringbuffer_size));
 	kfree(open_info);

[ 038/101] ehci: fix Lucid nohandoff pci quirk to be more generic with BIOS versions

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Anisse Astier <anisse@astier.eu>

commit c323dc023b9501e5d09582ec7efd1d40a9001d99 upstream.

BIOS vendors keep changing the BIOS versions. Only match the beginning
of the string to match all Lucid tablets with board name M11JB.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/pci-quirks.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/usb/host/pci-quirks.c
+++ b/drivers/usb/host/pci-quirks.c
@@ -545,7 +545,7 @@ static const struct dmi_system_id __devi
 		/*  Pegatron Lucid (Ordissimo AIRIS) */
 		.matches = {
 			DMI_MATCH(DMI_BOARD_NAME, "M11JB"),
-			DMI_MATCH(DMI_BIOS_VERSION, "Lucid-GE-133"),
+			DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
 		},
 	},
 	{ }

[ 039/101] ehci: Add yet-another Lucid nohandoff pci quirk

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Anisse Astier <anisse@astier.eu>

commit 8daf8b6086f9d575200cd0aa3797e26137255609 upstream.

Board name changed on another shipping Lucid tablet.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/pci-quirks.c |    7 +++++++
 1 file changed, 7 insertions(+)

--- a/drivers/usb/host/pci-quirks.c
+++ b/drivers/usb/host/pci-quirks.c
@@ -548,6 +548,13 @@ static const struct dmi_system_id __devi
 			DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
 		},
 	},
+	{
+		/*  Pegatron Lucid (Ordissimo) */
+		.matches = {
+			DMI_MATCH(DMI_BOARD_NAME, "Ordissimo"),
+			DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
+		},
+	},
 	{ }
 };
 

[ 040/101] usb-storage: add unusual_devs entry for Casio EX-N1 digital camera

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Michael Shigorin <mike@osdn.org.ua>

commit d7870af7e2e3a91b462075ec1ca669b482215187 upstream.

This commit sets removable subclass for Casio EX-N1 digital camera.

The patch has been tested within an ALT Linux kernel:
http://git.altlinux.org/people/led/packages/?p=kernel-image-3.0.git;a=commitdiff;h=c0fd891836e89fe0c93a4d536a59216d90e4e3e7

See also https://bugzilla.kernel.org/show_bug.cgi?id=49221

Signed-off-by: Oleksandr Chumachenko <ledest@gmail.com>
Signed-off-by: Michael Shigorin <mike@osdn.org.ua>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/storage/unusual_devs.h |    6 ++++++
 1 file changed, 6 insertions(+)

--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -1004,6 +1004,12 @@ UNUSUAL_DEV( 0x07cf, 0x1001, 0x1000, 0x9
 		USB_SC_8070, USB_PR_CB, NULL,
 		US_FL_NEED_OVERRIDE | US_FL_FIX_INQUIRY ),
 
+/* Submitted by Oleksandr Chumachenko <ledest@gmail.com> */
+UNUSUAL_DEV( 0x07cf, 0x1167, 0x0100, 0x0100,
+		"Casio",
+		"EX-N1 DigitalCamera",
+		USB_SC_8070, USB_PR_DEVICE, NULL, 0),
+
 /* Submitted by Hartmut Wahl <hwahl@hwahl.de>*/
 UNUSUAL_DEV( 0x0839, 0x000a, 0x0001, 0x0001,
 		"Samsung",

[ 041/101] USB: usb-wwan: fix multiple memory leaks in error paths

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit b8f0e82044c9ba40e92340c8a6d47d6bd6d819bc upstream.

Fix port-data memory leak in usb-serial probe error path by moving port
data allocation to port_probe.

Since commit a1028f0abf ("usb: usb_wwan: replace release and disconnect
with a port_remove hook") port data is deallocated in port_remove. This
leaves a possibility for memory leaks if usb-serial probe fails after
attach but before the port in question has been successfully registered.

Note that this patch also fixes two additional memory leaks in the error
path of attach should port initialisation fail for any port as the urbs
were never freed and neither was the data of any of the successfully
initialised ports.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/ipw.c      |    2 
 drivers/usb/serial/option.c   |    2 
 drivers/usb/serial/qcserial.c |    2 
 drivers/usb/serial/usb-wwan.h |    2 
 drivers/usb/serial/usb_wwan.c |  136 +++++++++++++++++-------------------------
 5 files changed, 60 insertions(+), 84 deletions(-)

--- a/drivers/usb/serial/ipw.c
+++ b/drivers/usb/serial/ipw.c
@@ -311,8 +311,8 @@ static struct usb_serial_driver ipw_devi
 	.open =			ipw_open,
 	.close =		ipw_close,
 	.probe =		ipw_probe,
-	.attach =		usb_wwan_startup,
 	.release =		ipw_release,
+	.port_probe =		usb_wwan_port_probe,
 	.port_remove =		usb_wwan_port_remove,
 	.dtr_rts =		ipw_dtr_rts,
 	.write =		usb_wwan_write,
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -1288,8 +1288,8 @@ static struct usb_serial_driver option_1
 	.tiocmget          = usb_wwan_tiocmget,
 	.tiocmset          = usb_wwan_tiocmset,
 	.ioctl             = usb_wwan_ioctl,
-	.attach            = usb_wwan_startup,
 	.release           = option_release,
+	.port_probe        = usb_wwan_port_probe,
 	.port_remove	   = usb_wwan_port_remove,
 	.read_int_callback = option_instat_callback,
 #ifdef CONFIG_PM
--- a/drivers/usb/serial/qcserial.c
+++ b/drivers/usb/serial/qcserial.c
@@ -287,8 +287,8 @@ static struct usb_serial_driver qcdevice
 	.write		     = usb_wwan_write,
 	.write_room	     = usb_wwan_write_room,
 	.chars_in_buffer     = usb_wwan_chars_in_buffer,
-	.attach		     = usb_wwan_startup,
 	.release	     = qc_release,
+	.port_probe          = usb_wwan_port_probe,
 	.port_remove	     = usb_wwan_port_remove,
 #ifdef CONFIG_PM
 	.suspend	     = usb_wwan_suspend,
--- a/drivers/usb/serial/usb-wwan.h
+++ b/drivers/usb/serial/usb-wwan.h
@@ -8,7 +8,7 @@
 extern void usb_wwan_dtr_rts(struct usb_serial_port *port, int on);
 extern int usb_wwan_open(struct tty_struct *tty, struct usb_serial_port *port);
 extern void usb_wwan_close(struct usb_serial_port *port);
-extern int usb_wwan_startup(struct usb_serial *serial);
+extern int usb_wwan_port_probe(struct usb_serial_port *port);
 extern int usb_wwan_port_remove(struct usb_serial_port *port);
 extern int usb_wwan_write_room(struct tty_struct *tty);
 extern void usb_wwan_set_termios(struct tty_struct *tty,
--- a/drivers/usb/serial/usb_wwan.c
+++ b/drivers/usb/serial/usb_wwan.c
@@ -447,10 +447,12 @@ void usb_wwan_close(struct usb_serial_po
 EXPORT_SYMBOL(usb_wwan_close);
 
 /* Helper functions used by usb_wwan_setup_urbs */
-static struct urb *usb_wwan_setup_urb(struct usb_serial *serial, int endpoint,
+static struct urb *usb_wwan_setup_urb(struct usb_serial_port *port,
+				      int endpoint,
 				      int dir, void *ctx, char *buf, int len,
 				      void (*callback) (struct urb *))
 {
+	struct usb_serial *serial = port->serial;
 	struct urb *urb;
 
 	if (endpoint == -1)
@@ -470,100 +472,74 @@ static struct urb *usb_wwan_setup_urb(st
 	return urb;
 }
 
-/* Setup urbs */
-static void usb_wwan_setup_urbs(struct usb_serial *serial)
+int usb_wwan_port_probe(struct usb_serial_port *port)
 {
-	int i, j;
-	struct usb_serial_port *port;
-	struct usb_wwan_port_private *portdata;
-
-	for (i = 0; i < serial->num_ports; i++) {
-		port = serial->port[i];
-		portdata = usb_get_serial_port_data(port);
-
-		/* Do indat endpoints first */
-		for (j = 0; j < N_IN_URB; ++j) {
-			portdata->in_urbs[j] = usb_wwan_setup_urb(serial,
-								  port->
-								  bulk_in_endpointAddress,
-								  USB_DIR_IN,
-								  port,
-								  portdata->
-								  in_buffer[j],
-								  IN_BUFLEN,
-								  usb_wwan_indat_callback);
-		}
-
-		/* outdat endpoints */
-		for (j = 0; j < N_OUT_URB; ++j) {
-			portdata->out_urbs[j] = usb_wwan_setup_urb(serial,
-								   port->
-								   bulk_out_endpointAddress,
-								   USB_DIR_OUT,
-								   port,
-								   portdata->
-								   out_buffer
-								   [j],
-								   OUT_BUFLEN,
-								   usb_wwan_outdat_callback);
-		}
-	}
-}
-
-int usb_wwan_startup(struct usb_serial *serial)
-{
-	int i, j, err;
-	struct usb_serial_port *port;
 	struct usb_wwan_port_private *portdata;
+	struct urb *urb;
 	u8 *buffer;
+	int err;
+	int i;
 
-	/* Now setup per port private data */
-	for (i = 0; i < serial->num_ports; i++) {
-		port = serial->port[i];
-		portdata = kzalloc(sizeof(*portdata), GFP_KERNEL);
-		if (!portdata) {
-			dbg("%s: kmalloc for usb_wwan_port_private (%d) failed!.",
-			    __func__, i);
-			return 1;
-		}
-		init_usb_anchor(&portdata->delayed);
-
-		for (j = 0; j < N_IN_URB; j++) {
-			buffer = (u8 *) __get_free_page(GFP_KERNEL);
-			if (!buffer)
-				goto bail_out_error;
-			portdata->in_buffer[j] = buffer;
-		}
-
-		for (j = 0; j < N_OUT_URB; j++) {
-			buffer = kmalloc(OUT_BUFLEN, GFP_KERNEL);
-			if (!buffer)
-				goto bail_out_error2;
-			portdata->out_buffer[j] = buffer;
-		}
+	portdata = kzalloc(sizeof(*portdata), GFP_KERNEL);
+	if (!portdata)
+		return -ENOMEM;
+
+	init_usb_anchor(&portdata->delayed);
+
+	for (i = 0; i < N_IN_URB; i++) {
+		buffer = (u8 *)__get_free_page(GFP_KERNEL);
+		if (!buffer)
+			goto bail_out_error;
+		portdata->in_buffer[i] = buffer;
+
+		urb = usb_wwan_setup_urb(port, port->bulk_in_endpointAddress,
+						USB_DIR_IN, port,
+						buffer, IN_BUFLEN,
+						usb_wwan_indat_callback);
+		portdata->in_urbs[i] = urb;
+ 	}
+	for (i = 0; i < N_OUT_URB; i++) {
+		if (port->bulk_out_endpointAddress == -1)
+			continue;
 
-		usb_set_serial_port_data(port, portdata);
+		buffer = kmalloc(OUT_BUFLEN, GFP_KERNEL);
+		if (!buffer)
+			goto bail_out_error2;
+		portdata->out_buffer[i] = buffer;
+
+		urb = usb_wwan_setup_urb(port, port->bulk_out_endpointAddress,
+						USB_DIR_OUT, port,
+						buffer, OUT_BUFLEN,
+						usb_wwan_outdat_callback);
+		portdata->out_urbs[i] = urb;
+	}
 
-		if (!port->interrupt_in_urb)
-			continue;
+	usb_set_serial_port_data(port, portdata);
+
+	if (port->interrupt_in_urb) {
 		err = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
 		if (err)
-			dbg("%s: submit irq_in urb failed %d", __func__, err);
+			dev_dbg(&port->dev, "%s: submit irq_in urb failed %d\n",
+				__func__, err);
 	}
-	usb_wwan_setup_urbs(serial);
+
 	return 0;
 
 bail_out_error2:
-	for (j = 0; j < N_OUT_URB; j++)
-		kfree(portdata->out_buffer[j]);
+	for (i = 0; i < N_OUT_URB; i++) {
+		usb_free_urb(portdata->out_urbs[i]);
+		kfree(portdata->out_buffer[i]);
+	}
 bail_out_error:
-	for (j = 0; j < N_IN_URB; j++)
-		if (portdata->in_buffer[j])
-			free_page((unsigned long)portdata->in_buffer[j]);
+	for (i = 0; i < N_IN_URB; i++) {
+		usb_free_urb(portdata->in_urbs[i]);
+		free_page((unsigned long)portdata->in_buffer[i]);
+	}
 	kfree(portdata);
-	return 1;
+
+	return -ENOMEM;
 }
-EXPORT_SYMBOL(usb_wwan_startup);
+EXPORT_SYMBOL_GPL(usb_wwan_port_probe);
 
 int usb_wwan_port_remove(struct usb_serial_port *port)
 {

[ 042/101] usb hub: send clear_tt_buffer_complete events when canceling TT clear work

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Octavian Purdila <octavian.purdila@intel.com>

commit 3b6054da68f9b0d5ed6a7ed0f42a79e61904352c upstream.

There is a race condition in the USB hub code with regard to handling
TT clear requests that can get the HCD driver in a deadlock. Usually
when an TT clear request is scheduled it will be executed immediately:

<7>[    6.077583] usb 2-1.3: unlink qh1-0e01/f4d4db00 start 0 [1/2 us]
<3>[    6.078041] usb 2-1: clear tt buffer port 3, a3 ep2 t04048d82
<7>[    6.078299] hub_tt_work:731
<7>[    9.309089] usb 2-1.5: link qh1-0e01/f4d506c0 start 0 [1/2 us]
<7>[    9.324526] ehci_hcd 0000:00:1d.0: reused qh f4d4db00 schedule
<7>[    9.324539] usb 2-1.3: link qh1-0e01/f4d4db00 start 0 [1/2 us]
<7>[    9.341530] usb 1-1.1: link qh4-0e01/f397aec0 start 2 [1/2 us]
<7>[   10.116159] usb 2-1.3: unlink qh1-0e01/f4d4db00 start 0 [1/2 us]
<3>[   10.116459] usb 2-1: clear tt buffer port 3, a3 ep2 t04048d82
<7>[   10.116537] hub_tt_work:731

However, if a suspend operation is triggered before hub_tt_work is
scheduled, hub_quiesce will cancel the work without notifying the HCD
driver:

<3>[   35.033941] usb 2-1: clear tt buffer port 3, a3 ep2 t04048d80
<5>[   35.034022] sd 0:0:0:0: [sda] Stopping disk
<7>[   35.034039] hub 2-1:1.0: hub_suspend
<7>[   35.034067] usb 2-1: unlink qh256-0001/f3b1ab00 start 1 [1/0 us]
<7>[   35.035085] hub 1-0:1.0: hub_suspend
<7>[   35.035102] usb usb1: bus suspend, wakeup 0
<7>[   35.035106] ehci_hcd 0000:00:1a.0: suspend root hub
<7>[   35.035298] hub 2-0:1.0: hub_suspend
<7>[   35.035313] usb usb2: bus suspend, wakeup 0
<7>[   35.035315] ehci_hcd 0000:00:1d.0: suspend root hub
<6>[   35.250017] PM: suspend of devices complete after 216.979 msecs
<6>[   35.250822] PM: late suspend of devices complete after 0.799 msecs
<7>[   35.252343] ehci_hcd 0000:00:1d.0: wakeup: 1
<7>[   35.262923] ehci_hcd 0000:00:1d.0: --> PCI D3hot
<7>[   35.263302] ehci_hcd 0000:00:1a.0: wakeup: 1
<7>[   35.273912] ehci_hcd 0000:00:1a.0: --> PCI D3hot
<6>[   35.274254] PM: noirq suspend of devices complete after 23.442 msecs
<6>[   35.274975] ACPI: Preparing to enter system sleep state S3
<6>[   35.292666] PM: Saving platform NVS memory
<7>[   35.295030] Disabling non-boot CPUs ...
<6>[   35.297351] CPU 1 is now offline
<6>[   35.300345] CPU 2 is now offline
<6>[   35.303929] CPU 3 is now offline
<7>[   35.303931] lockdep: fixing up alternatives.
<6>[   35.304825] Extended CMOS year: 2000

When the device will resume the EHCI driver will get stuck in
ehci_endpoint_disable waiting for the tt_clearing flag to reset:

<0>[   47.610967] usb 2-1.3: **** DPM device timeout ****
<7>[   47.610972]  f2f11c60 00000092 f2f11c0c c10624a5 00000003 f4c6e880 c1c8a4c0 c1c8a4c0
<7>[   47.610983]  15c55698 0000000b f56b34c0 f2a45b70 f4c6e880 00000082 f2a4602c f2f11c30
<7>[   47.610993]  c10787f8 f4cac000 f2a45b70 00000000 f4cac010 f2f11c58 00000046 00000001
<7>[   47.611004] Call Trace:
<7>[   47.611006]  [<c10624a5>] ? sched_clock_cpu+0xf5/0x160
<7>[   47.611019]  [<c10787f8>] ? lock_release_holdtime.part.22+0x88/0xf0
<7>[   47.611026]  [<c103ed46>] ? lock_timer_base.isra.35+0x26/0x50
<7>[   47.611034]  [<c17592d3>] ? schedule_timeout+0x133/0x290
<7>[   47.611044]  [<c175b43e>] schedule+0x1e/0x50
<7>[   47.611051]  [<c17592d8>] schedule_timeout+0x138/0x290
<7>[   47.611057]  [<c10624a5>] ? sched_clock_cpu+0xf5/0x160
<7>[   47.611063]  [<c103e560>] ? usleep_range+0x40/0x40
<7>[   47.611070]  [<c1759445>] schedule_timeout_uninterruptible+0x15/0x20
<7>[   47.611077]  [<c14935f4>] ehci_endpoint_disable+0x64/0x160
<7>[   47.611084]  [<c147d1ee>] ? usb_hcd_flush_endpoint+0x10e/0x1d0
<7>[   47.611092]  [<c1165663>] ? sysfs_add_file+0x13/0x20
<7>[   47.611100]  [<c147d5a9>] usb_hcd_disable_endpoint+0x29/0x40
<7>[   47.611107]  [<c147fafc>] usb_disable_endpoint+0x5c/0x80
<7>[   47.611111]  [<c147fb57>] usb_disable_interface+0x37/0x50
<7>[   47.611116]  [<c1477650>] usb_reset_and_verify_device+0x4b0/0x640
<7>[   47.611122]  [<c1474665>] ? hub_port_status+0xb5/0x100
<7>[   47.611129]  [<c147a975>] usb_port_resume+0xd5/0x220
<7>[   47.611136]  [<c148877f>] generic_resume+0xf/0x30
<7>[   47.611142]  [<c14821a3>] usb_resume+0x133/0x180
<7>[   47.611147]  [<c1473b10>] ? usb_dev_thaw+0x10/0x10
<7>[   47.611152]  [<c1473b1d>] usb_dev_resume+0xd/0x10
<7>[   47.611157]  [<c13baa60>] dpm_run_callback+0x40/0xb0
<7>[   47.611164]  [<c13bdb03>] ? pm_runtime_enable+0x43/0x70
<7>[   47.611171]  [<c13bafc6>] device_resume+0x1a6/0x2c0
<7>[   47.611177]  [<c13ba940>] ? dpm_show_time+0xe0/0xe0
<7>[   47.611183]  [<c13bb0f9>] async_resume+0x19/0x40
<7>[   47.611189]  [<c10580c4>] async_run_entry_fn+0x64/0x160
<7>[   47.611196]  [<c104a244>] ? process_one_work+0x104/0x480
<7>[   47.611203]  [<c104a24c>] ? process_one_work+0x10c/0x480
<7>[   47.611209]  [<c104a2c0>] process_one_work+0x180/0x480
<7>[   47.611215]  [<c104a244>] ? process_one_work+0x104/0x480
<7>[   47.611220]  [<c1058060>] ? async_schedule+0x10/0x10
<7>[   47.611226]  [<c104c15c>] worker_thread+0x11c/0x2f0
<7>[   47.611233]  [<c104c040>] ? manage_workers.isra.27+0x1f0/0x1f0
<7>[   47.611239]  [<c10507f8>] kthread+0x78/0x80
<7>[   47.611244]  [<c1750000>] ? timer_cpu_notify+0xd6/0x20d
<7>[   47.611253]  [<c1050780>] ? __init_kthread_worker+0x60/0x60
<7>[   47.611258]  [<c176357e>] kernel_thread_helper+0x6/0xd
<7>[   47.611283] ------------[ cut here ]------------

This patch changes hub_quiesce behavior to flush the TT clear work
instead of canceling it, to make sure that no TT clear request remains
uncompleted before suspend.

Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/core/hub.c |    7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -730,13 +730,16 @@ static void hub_tt_work(struct work_stru
 	int			limit = 100;
 
 	spin_lock_irqsave (&hub->tt.lock, flags);
-	while (--limit && !list_empty (&hub->tt.clear_list)) {
+	while (!list_empty(&hub->tt.clear_list)) {
 		struct list_head	*next;
 		struct usb_tt_clear	*clear;
 		struct usb_device	*hdev = hub->hdev;
 		const struct hc_driver	*drv;
 		int			status;
 
+		if (!hub->quiescing && --limit < 0)
+			break;
+
 		next = hub->tt.clear_list.next;
 		clear = list_entry (next, struct usb_tt_clear, clear_list);
 		list_del (&clear->clear_list);
@@ -1201,7 +1204,7 @@ static void hub_quiesce(struct usb_hub *
 	if (hub->has_indicators)
 		cancel_delayed_work_sync(&hub->leds);
 	if (hub->tt.hub)
-		cancel_work_sync(&hub->tt.clear_work);
+		flush_work_sync(&hub->tt.clear_work);
 }
 
 /* caller has locked the hub device */

[ 043/101] USB: ch341: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 456c5be56ed070a4d883c60b587bcc1c97a8cf3e upstream.

Fix port-data memory leak by moving port data allocation to port_probe
and actually implementing deallocation.

Note that this driver has never even bothered to try to deallocate it's
port data...

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/ch341.c |   23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)

--- a/drivers/usb/serial/ch341.c
+++ b/drivers/usb/serial/ch341.c
@@ -241,13 +241,11 @@ out:	kfree(buffer);
 	return r;
 }
 
-/* allocate private data */
-static int ch341_attach(struct usb_serial *serial)
+static int ch341_port_probe(struct usb_serial_port *port)
 {
 	struct ch341_private *priv;
 	int r;
 
-	/* private data */
 	priv = kzalloc(sizeof(struct ch341_private), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
@@ -257,17 +255,27 @@ static int ch341_attach(struct usb_seria
 	priv->baud_rate = DEFAULT_BAUD_RATE;
 	priv->line_control = CH341_BIT_RTS | CH341_BIT_DTR;
 
-	r = ch341_configure(serial->dev, priv);
+	r = ch341_configure(port->serial->dev, priv);
 	if (r < 0)
 		goto error;
 
-	usb_set_serial_port_data(serial->port[0], priv);
+	usb_set_serial_port_data(port, priv);
 	return 0;
 
 error:	kfree(priv);
 	return r;
 }
 
+static int ch341_port_remove(struct usb_serial_port *port)
+{
+	struct ch341_private *priv;
+
+	priv = usb_get_serial_port_data(port);
+	kfree(priv);
+
+	return 0;
+}
+
 static int ch341_carrier_raised(struct usb_serial_port *port)
 {
 	struct ch341_private *priv = usb_get_serial_port_data(port);
@@ -303,7 +311,7 @@ static void ch341_close(struct usb_seria
 static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port)
 {
 	struct usb_serial *serial = port->serial;
-	struct ch341_private *priv = usb_get_serial_port_data(serial->port[0]);
+	struct ch341_private *priv = usb_get_serial_port_data(port);
 	int r;
 
 	priv->baud_rate = DEFAULT_BAUD_RATE;
@@ -606,7 +614,8 @@ static struct usb_serial_driver ch341_de
 	.tiocmget          = ch341_tiocmget,
 	.tiocmset          = ch341_tiocmset,
 	.read_int_callback = ch341_read_int_callback,
-	.attach            = ch341_attach,
+	.port_probe        = ch341_port_probe,
+	.port_remove       = ch341_port_remove,
 	.reset_resume      = ch341_reset_resume,
 };
 

[ 044/101] USB: digi_acceleport: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit fb44ff854e148bc5c5982dad32da98b7a0989d2d upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the oob port is never registered as a port device and should
thus be handled in attach and release.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/digi_acceleport.c |  117 ++++++++++++++++++++---------------
 1 file changed, 67 insertions(+), 50 deletions(-)

--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -244,6 +244,8 @@ static int digi_startup_device(struct us
 static int digi_startup(struct usb_serial *serial);
 static void digi_disconnect(struct usb_serial *serial);
 static void digi_release(struct usb_serial *serial);
+static int digi_port_probe(struct usb_serial_port *port);
+static int digi_port_remove(struct usb_serial_port *port);
 static void digi_read_bulk_callback(struct urb *urb);
 static int digi_read_inb_callback(struct urb *urb);
 static int digi_read_oob_callback(struct urb *urb);
@@ -298,6 +300,8 @@ static struct usb_serial_driver digi_acc
 	.attach =			digi_startup,
 	.disconnect =			digi_disconnect,
 	.release =			digi_release,
+	.port_probe =			digi_port_probe,
+	.port_remove =			digi_port_remove,
 };
 
 static struct usb_serial_driver digi_acceleport_4_device = {
@@ -324,6 +328,8 @@ static struct usb_serial_driver digi_acc
 	.attach =			digi_startup,
 	.disconnect =			digi_disconnect,
 	.release =			digi_release,
+	.port_probe =			digi_port_probe,
+	.port_remove =			digi_port_remove,
 };
 
 static struct usb_serial_driver * const serial_drivers[] = {
@@ -1237,59 +1243,50 @@ static int digi_startup_device(struct us
 	return ret;
 }
 
+static int digi_port_init(struct usb_serial_port *port, unsigned port_num)
+{
+	struct digi_port *priv;
+
+	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	spin_lock_init(&priv->dp_port_lock);
+	priv->dp_port_num = port_num;
+	init_waitqueue_head(&priv->dp_modem_change_wait);
+	init_waitqueue_head(&priv->dp_transmit_idle_wait);
+	init_waitqueue_head(&priv->dp_flush_wait);
+	init_waitqueue_head(&priv->dp_close_wait);
+	INIT_WORK(&priv->dp_wakeup_work, digi_wakeup_write_lock);
+	priv->dp_port = port;
+
+	init_waitqueue_head(&port->write_wait);
+
+	usb_set_serial_port_data(port, priv);
+
+	return 0;
+}
 
 static int digi_startup(struct usb_serial *serial)
 {
-
-	int i;
-	struct digi_port *priv;
 	struct digi_serial *serial_priv;
+	int ret;
 
-	/* allocate the private data structures for all ports */
-	/* number of regular ports + 1 for the out-of-band port */
-	for (i = 0; i < serial->type->num_ports + 1; i++) {
-		/* allocate port private structure */
-		priv = kmalloc(sizeof(struct digi_port), GFP_KERNEL);
-		if (priv == NULL) {
-			while (--i >= 0)
-				kfree(usb_get_serial_port_data(serial->port[i]));
-			return 1;			/* error */
-		}
+	serial_priv = kzalloc(sizeof(*serial_priv), GFP_KERNEL);
+	if (!serial_priv)
+		return -ENOMEM;
 
-		/* initialize port private structure */
-		spin_lock_init(&priv->dp_port_lock);
-		priv->dp_port_num = i;
-		priv->dp_out_buf_len = 0;
-		priv->dp_write_urb_in_use = 0;
-		priv->dp_modem_signals = 0;
-		init_waitqueue_head(&priv->dp_modem_change_wait);
-		priv->dp_transmit_idle = 0;
-		init_waitqueue_head(&priv->dp_transmit_idle_wait);
-		priv->dp_throttled = 0;
-		priv->dp_throttle_restart = 0;
-		init_waitqueue_head(&priv->dp_flush_wait);
-		init_waitqueue_head(&priv->dp_close_wait);
-		INIT_WORK(&priv->dp_wakeup_work, digi_wakeup_write_lock);
-		priv->dp_port = serial->port[i];
-		/* initialize write wait queue for this port */
-		init_waitqueue_head(&serial->port[i]->write_wait);
-
-		usb_set_serial_port_data(serial->port[i], priv);
-	}
-
-	/* allocate serial private structure */
-	serial_priv = kmalloc(sizeof(struct digi_serial), GFP_KERNEL);
-	if (serial_priv == NULL) {
-		for (i = 0; i < serial->type->num_ports + 1; i++)
-			kfree(usb_get_serial_port_data(serial->port[i]));
-		return 1;			/* error */
-	}
-
-	/* initialize serial private structure */
 	spin_lock_init(&serial_priv->ds_serial_lock);
 	serial_priv->ds_oob_port_num = serial->type->num_ports;
 	serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num];
-	serial_priv->ds_device_started = 0;
+
+	ret = digi_port_init(serial_priv->ds_oob_port,
+						serial_priv->ds_oob_port_num);
+	if (ret) {
+		kfree(serial_priv);
+		return ret;
+	}
+
 	usb_set_serial_data(serial, serial_priv);
 
 	return 0;
@@ -1310,15 +1307,35 @@ static void digi_disconnect(struct usb_s
 
 static void digi_release(struct usb_serial *serial)
 {
-	int i;
+	struct digi_serial *serial_priv;
+	struct digi_port *priv;
+
+	serial_priv = usb_get_serial_data(serial);
+
+	priv = usb_get_serial_port_data(serial_priv->ds_oob_port);
+	kfree(priv);
 
-	/* free the private data structures for all ports */
-	/* number of regular ports + 1 for the out-of-band port */
-	for (i = 0; i < serial->type->num_ports + 1; i++)
-		kfree(usb_get_serial_port_data(serial->port[i]));
-	kfree(usb_get_serial_data(serial));
+	kfree(serial_priv);
 }
 
+static int digi_port_probe(struct usb_serial_port *port)
+{
+	unsigned port_num;
+
+	port_num = port->number - port->serial->minor;
+
+	return digi_port_init(port, port_num);
+}
+
+static int digi_port_remove(struct usb_serial_port *port)
+{
+	struct digi_port *priv;
+
+	priv = usb_get_serial_port_data(port);
+	kfree(priv);
+
+	return 0;
+}
 
 static void digi_read_bulk_callback(struct urb *urb)
 {

[ 045/101] USB: ipw: fix interface-data memory leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit a997448c89905b80aa4022f734f03685e733d711 upstream.

Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/ipw.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

--- a/drivers/usb/serial/ipw.c
+++ b/drivers/usb/serial/ipw.c
@@ -209,8 +209,7 @@ static int ipw_open(struct tty_struct *t
 	return 0;
 }
 
-/* fake probe - only to allocate data structures */
-static int ipw_probe(struct usb_serial *serial, const struct usb_device_id *id)
+static int ipw_attach(struct usb_serial *serial)
 {
 	struct usb_wwan_intf_private *data;
 
@@ -310,7 +309,7 @@ static struct usb_serial_driver ipw_devi
 	.num_ports =		1,
 	.open =			ipw_open,
 	.close =		ipw_close,
-	.probe =		ipw_probe,
+	.attach =		ipw_attach,
 	.release =		ipw_release,
 	.port_probe =		usb_wwan_port_probe,
 	.port_remove =		usb_wwan_port_remove,

[ 046/101] USB: mct_u232: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit a8f2ae7a3aa59079d7e7e1ddf5007f03532f458c upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the write waitqueue was initialised but never used.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mct_u232.c |   45 +++++++++++++++++++++++-------------------
 1 file changed, 25 insertions(+), 20 deletions(-)

--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -51,7 +51,8 @@ static bool debug;
  * Function prototypes
  */
 static int  mct_u232_startup(struct usb_serial *serial);
-static void mct_u232_release(struct usb_serial *serial);
+static int  mct_u232_port_probe(struct usb_serial_port *port);
+static int  mct_u232_port_remove(struct usb_serial_port *remove);
 static int  mct_u232_open(struct tty_struct *tty, struct usb_serial_port *port);
 static void mct_u232_close(struct usb_serial_port *port);
 static void mct_u232_dtr_rts(struct usb_serial_port *port, int on);
@@ -101,7 +102,8 @@ static struct usb_serial_driver mct_u232
 	.tiocmget =	     mct_u232_tiocmget,
 	.tiocmset =	     mct_u232_tiocmset,
 	.attach =	     mct_u232_startup,
-	.release =	     mct_u232_release,
+	.port_probe =        mct_u232_port_probe,
+	.port_remove =       mct_u232_port_remove,
 	.ioctl =             mct_u232_ioctl,
 	.get_icount =        mct_u232_get_icount,
 };
@@ -392,18 +394,8 @@ static void mct_u232_msr_to_state(unsign
 
 static int mct_u232_startup(struct usb_serial *serial)
 {
-	struct mct_u232_private *priv;
 	struct usb_serial_port *port, *rport;
 
-	priv = kzalloc(sizeof(struct mct_u232_private), GFP_KERNEL);
-	if (!priv)
-		return -ENOMEM;
-	spin_lock_init(&priv->lock);
-	init_waitqueue_head(&priv->msr_wait);
-	usb_set_serial_port_data(serial->port[0], priv);
-
-	init_waitqueue_head(&serial->port[0]->write_wait);
-
 	/* Puh, that's dirty */
 	port = serial->port[0];
 	rport = serial->port[1];
@@ -416,18 +408,31 @@ static int mct_u232_startup(struct usb_s
 	return 0;
 } /* mct_u232_startup */
 
+static int mct_u232_port_probe(struct usb_serial_port *port)
+{
+	struct mct_u232_private *priv;
+
+	priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
 
-static void mct_u232_release(struct usb_serial *serial)
+	spin_lock_init(&priv->lock);
+	init_waitqueue_head(&priv->msr_wait);
+
+	usb_set_serial_port_data(port, priv);
+
+	return 0;
+}
+
+static int mct_u232_port_remove(struct usb_serial_port *port)
 {
 	struct mct_u232_private *priv;
-	int i;
 
-	for (i = 0; i < serial->num_ports; ++i) {
-		/* My special items, the standard routines free my urbs */
-		priv = usb_get_serial_port_data(serial->port[i]);
-		kfree(priv);
-	}
-} /* mct_u232_release */
+	priv = usb_get_serial_port_data(port);
+	kfree(priv);
+
+	return 0;
+}
 
 static int  mct_u232_open(struct tty_struct *tty, struct usb_serial_port *port)
 {

[ 047/101] USB: mct_u232: fix broken close

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 5260e458f5eff269a43e4f1e9c47186c57b88ddb upstream.

Make sure generic close is called at close.

The driver relies on the generic write implementation but did not call
generic close.

Note that the call to kill the read urb is not redundant, as mct_u232
uses an interrupt urb from the second port as the read urb and that
generic close therefore fails to kill it.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mct_u232.c |   14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)

--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -524,12 +524,14 @@ static void mct_u232_dtr_rts(struct usb_
 
 static void mct_u232_close(struct usb_serial_port *port)
 {
-	if (port->serial->dev) {
-		/* shutdown our urbs */
-		usb_kill_urb(port->write_urb);
-		usb_kill_urb(port->read_urb);
-		usb_kill_urb(port->interrupt_in_urb);
-	}
+	/*
+	 * Must kill the read urb as it is actually an interrupt urb, which
+	 * generic close thus fails to kill.
+	 */
+	usb_kill_urb(port->read_urb);
+	usb_kill_urb(port->interrupt_in_urb);
+
+	usb_serial_generic_close(port);
 } /* mct_u232_close */
 
 

[ 048/101] USB: option: fix interface-data memory leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit c2dd4a8eac7821fed2c2d19e4607d0986b53b0fe upstream.

Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.

Note that the usb device id is stored at probe so that it can be used
in attach to determine send-setup blacklisting.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/option.c |   21 +++++++++++++++++++--
 1 file changed, 19 insertions(+), 2 deletions(-)

--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -47,6 +47,7 @@
 /* Function prototypes */
 static int  option_probe(struct usb_serial *serial,
 			const struct usb_device_id *id);
+static int option_attach(struct usb_serial *serial);
 static void option_release(struct usb_serial *serial);
 static int option_send_setup(struct usb_serial_port *port);
 static void option_instat_callback(struct urb *urb);
@@ -1288,6 +1289,7 @@ static struct usb_serial_driver option_1
 	.tiocmget          = usb_wwan_tiocmget,
 	.tiocmset          = usb_wwan_tiocmset,
 	.ioctl             = usb_wwan_ioctl,
+	.attach            = option_attach,
 	.release           = option_release,
 	.port_probe        = usb_wwan_port_probe,
 	.port_remove	   = usb_wwan_port_remove,
@@ -1337,8 +1339,6 @@ static bool is_blacklisted(const u8 ifnu
 static int option_probe(struct usb_serial *serial,
 			const struct usb_device_id *id)
 {
-	struct usb_wwan_intf_private *data;
-	struct option_private *priv;
 	struct usb_interface_descriptor *iface_desc =
 				&serial->interface->cur_altsetting->desc;
 	struct usb_device_descriptor *dev_desc = &serial->dev->descriptor;
@@ -1376,6 +1376,19 @@ static int option_probe(struct usb_seria
 		iface_desc->bInterfaceClass != USB_CLASS_CDC_DATA)
 		return -ENODEV;
 
+	/* Store device id so we can use it during attach. */
+	usb_set_serial_data(serial, (void *)id);
+
+	return 0;
+}
+
+static int option_attach(struct usb_serial *serial)
+{
+	struct usb_interface_descriptor *iface_desc;
+	const struct usb_device_id *id;
+	struct usb_wwan_intf_private *data;
+	struct option_private *priv;
+
 	data = kzalloc(sizeof(struct usb_wwan_intf_private), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
@@ -1386,6 +1399,10 @@ static int option_probe(struct usb_seria
 		return -ENOMEM;
 	}
 
+	/* Retrieve device id stored at probe. */
+	id = usb_get_serial_data(serial);
+	iface_desc = &serial->interface->cur_altsetting->desc;
+
 	priv->bInterfaceNumber = iface_desc->bInterfaceNumber;
 	data->private = priv;
 

[ 049/101] USB: keyspan: fix NULL-pointer dereferences and memory leaks

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit f79b2d0fe81eecb412dc48e87a119afc690da8e9 upstream.

Fix NULL-pointer dereference at release by moving port data allocation
and deallocation to port_probe and port_remove.

Fix NULL-pointer dereference at disconnect by stopping port urbs at
port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer accessible at
disconnect or release.

Note that this patch also fixes port and interface-data memory leaks in
the error path of attach should port initialisation fail for any port.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/keyspan.c |  183 ++++++++++++++++++++-----------------------
 drivers/usb/serial/keyspan.h |    8 +
 2 files changed, 96 insertions(+), 95 deletions(-)

--- a/drivers/usb/serial/keyspan.c
+++ b/drivers/usb/serial/keyspan.c
@@ -1392,13 +1392,9 @@ static struct callbacks {
 	   data in device_details */
 static void keyspan_setup_urbs(struct usb_serial *serial)
 {
-	int				i, j;
 	struct keyspan_serial_private 	*s_priv;
 	const struct keyspan_device_details	*d_details;
-	struct usb_serial_port		*port;
-	struct keyspan_port_private	*p_priv;
 	struct callbacks		*cback;
-	int				endp;
 
 	s_priv = usb_get_serial_data(serial);
 	d_details = s_priv->device_details;
@@ -1422,45 +1418,6 @@ static void keyspan_setup_urbs(struct us
 		(serial, d_details->glocont_endpoint, USB_DIR_OUT,
 		 serial, s_priv->glocont_buf, GLOCONT_BUFLEN,
 		 cback->glocont_callback);
-
-	/* Setup endpoints for each port specific thing */
-	for (i = 0; i < d_details->num_ports; i++) {
-		port = serial->port[i];
-		p_priv = usb_get_serial_port_data(port);
-
-		/* Do indat endpoints first, once for each flip */
-		endp = d_details->indat_endpoints[i];
-		for (j = 0; j <= d_details->indat_endp_flip; ++j, ++endp) {
-			p_priv->in_urbs[j] = keyspan_setup_urb
-				(serial, endp, USB_DIR_IN, port,
-				 p_priv->in_buffer[j], 64,
-				 cback->indat_callback);
-		}
-		for (; j < 2; ++j)
-			p_priv->in_urbs[j] = NULL;
-
-		/* outdat endpoints also have flip */
-		endp = d_details->outdat_endpoints[i];
-		for (j = 0; j <= d_details->outdat_endp_flip; ++j, ++endp) {
-			p_priv->out_urbs[j] = keyspan_setup_urb
-				(serial, endp, USB_DIR_OUT, port,
-				 p_priv->out_buffer[j], 64,
-				 cback->outdat_callback);
-		}
-		for (; j < 2; ++j)
-			p_priv->out_urbs[j] = NULL;
-
-		/* inack endpoint */
-		p_priv->inack_urb = keyspan_setup_urb
-			(serial, d_details->inack_endpoints[i], USB_DIR_IN,
-			 port, p_priv->inack_buffer, 1, cback->inack_callback);
-
-		/* outcont endpoint */
-		p_priv->outcont_urb = keyspan_setup_urb
-			(serial, d_details->outcont_endpoints[i], USB_DIR_OUT,
-			 port, p_priv->outcont_buffer, 64,
-			 cback->outcont_callback);
-	}
 }
 
 /* usa19 function doesn't require prescaler */
@@ -2422,9 +2379,7 @@ static void keyspan_send_setup(struct us
 static int keyspan_startup(struct usb_serial *serial)
 {
 	int				i, err;
-	struct usb_serial_port		*port;
 	struct keyspan_serial_private 	*s_priv;
-	struct keyspan_port_private	*p_priv;
 	const struct keyspan_device_details	*d_details;
 
 	for (i = 0; (d_details = keyspan_devices[i]) != NULL; ++i)
@@ -2448,19 +2403,6 @@ static int keyspan_startup(struct usb_se
 	s_priv->device_details = d_details;
 	usb_set_serial_data(serial, s_priv);
 
-	/* Now setup per port private data */
-	for (i = 0; i < serial->num_ports; i++) {
-		port = serial->port[i];
-		p_priv = kzalloc(sizeof(struct keyspan_port_private),
-								GFP_KERNEL);
-		if (!p_priv) {
-			dbg("%s - kmalloc for keyspan_port_private (%d) failed!.", __func__, i);
-			return 1;
-		}
-		p_priv->device_details = d_details;
-		usb_set_serial_port_data(port, p_priv);
-	}
-
 	keyspan_setup_urbs(serial);
 
 	if (s_priv->instat_urb != NULL) {
@@ -2481,61 +2423,112 @@ static int keyspan_startup(struct usb_se
 
 static void keyspan_disconnect(struct usb_serial *serial)
 {
-	int				i, j;
-	struct usb_serial_port		*port;
-	struct keyspan_serial_private 	*s_priv;
-	struct keyspan_port_private	*p_priv;
+	struct keyspan_serial_private *s_priv;
 
 	s_priv = usb_get_serial_data(serial);
 
-	/* Stop reading/writing urbs */
 	stop_urb(s_priv->instat_urb);
 	stop_urb(s_priv->glocont_urb);
 	stop_urb(s_priv->indat_urb);
-	for (i = 0; i < serial->num_ports; ++i) {
-		port = serial->port[i];
-		p_priv = usb_get_serial_port_data(port);
-		stop_urb(p_priv->inack_urb);
-		stop_urb(p_priv->outcont_urb);
-		for (j = 0; j < 2; j++) {
-			stop_urb(p_priv->in_urbs[j]);
-			stop_urb(p_priv->out_urbs[j]);
-		}
-	}
+}
+
+static void keyspan_release(struct usb_serial *serial)
+{
+	struct keyspan_serial_private *s_priv;
+
+	s_priv = usb_get_serial_data(serial);
 
-	/* Now free them */
 	usb_free_urb(s_priv->instat_urb);
 	usb_free_urb(s_priv->indat_urb);
 	usb_free_urb(s_priv->glocont_urb);
-	for (i = 0; i < serial->num_ports; ++i) {
-		port = serial->port[i];
-		p_priv = usb_get_serial_port_data(port);
-		usb_free_urb(p_priv->inack_urb);
-		usb_free_urb(p_priv->outcont_urb);
-		for (j = 0; j < 2; j++) {
-			usb_free_urb(p_priv->in_urbs[j]);
-			usb_free_urb(p_priv->out_urbs[j]);
-		}
-	}
+
+	kfree(s_priv);
 }
 
-static void keyspan_release(struct usb_serial *serial)
+static int keyspan_port_probe(struct usb_serial_port *port)
 {
-	int				i;
-	struct usb_serial_port		*port;
-	struct keyspan_serial_private 	*s_priv;
+	struct usb_serial *serial = port->serial;
+	struct keyspan_port_private *s_priv;
+	struct keyspan_port_private *p_priv;
+	const struct keyspan_device_details *d_details;
+	struct callbacks *cback;
+	int endp;
+	int port_num;
+	int i;
 
 	s_priv = usb_get_serial_data(serial);
+	d_details = s_priv->device_details;
 
-	/*  dbg("Freeing serial->private."); */
-	kfree(s_priv);
+	p_priv = kzalloc(sizeof(*p_priv), GFP_KERNEL);
+	if (!p_priv)
+		return -ENOMEM;
+
+	s_priv = usb_get_serial_data(port->serial);
+	p_priv->device_details = d_details;
+
+	/* Setup values for the various callback routines */
+	cback = &keyspan_callbacks[d_details->msg_format];
+
+	port_num = port->number - port->serial->minor;
+
+	/* Do indat endpoints first, once for each flip */
+	endp = d_details->indat_endpoints[port_num];
+	for (i = 0; i <= d_details->indat_endp_flip; ++i, ++endp) {
+		p_priv->in_urbs[i] = keyspan_setup_urb(serial, endp,
+						USB_DIR_IN, port,
+						p_priv->in_buffer[i], 64,
+						cback->indat_callback);
+	}
+	/* outdat endpoints also have flip */
+	endp = d_details->outdat_endpoints[port_num];
+	for (i = 0; i <= d_details->outdat_endp_flip; ++i, ++endp) {
+		p_priv->out_urbs[i] = keyspan_setup_urb(serial, endp,
+						USB_DIR_OUT, port,
+						p_priv->out_buffer[i], 64,
+						cback->outdat_callback);
+	}
+	/* inack endpoint */
+	p_priv->inack_urb = keyspan_setup_urb(serial,
+					d_details->inack_endpoints[port_num],
+					USB_DIR_IN, port,
+					p_priv->inack_buffer, 1,
+					cback->inack_callback);
+	/* outcont endpoint */
+	p_priv->outcont_urb = keyspan_setup_urb(serial,
+					d_details->outcont_endpoints[port_num],
+					USB_DIR_OUT, port,
+					p_priv->outcont_buffer, 64,
+					 cback->outcont_callback);
+
+	usb_set_serial_port_data(port, p_priv);
 
-	/*  dbg("Freeing port->private."); */
-	/* Now free per port private data */
-	for (i = 0; i < serial->num_ports; i++) {
-		port = serial->port[i];
-		kfree(usb_get_serial_port_data(port));
+	return 0;
+}
+
+static int keyspan_port_remove(struct usb_serial_port *port)
+{
+	struct keyspan_port_private *p_priv;
+	int i;
+
+	p_priv = usb_get_serial_port_data(port);
+
+	stop_urb(p_priv->inack_urb);
+	stop_urb(p_priv->outcont_urb);
+	for (i = 0; i < 2; i++) {
+		stop_urb(p_priv->in_urbs[i]);
+		stop_urb(p_priv->out_urbs[i]);
+	}
+
+	usb_free_urb(p_priv->inack_urb);
+	usb_free_urb(p_priv->outcont_urb);
+	for (i = 0; i < 2; i++) {
+		usb_free_urb(p_priv->in_urbs[i]);
+		usb_free_urb(p_priv->out_urbs[i]);
 	}
+
+	kfree(p_priv);
+
+	return 0;
 }
 
 MODULE_AUTHOR(DRIVER_AUTHOR);
--- a/drivers/usb/serial/keyspan.h
+++ b/drivers/usb/serial/keyspan.h
@@ -42,6 +42,8 @@ static void keyspan_dtr_rts		(struct usb
 static int  keyspan_startup		(struct usb_serial *serial);
 static void keyspan_disconnect		(struct usb_serial *serial);
 static void keyspan_release		(struct usb_serial *serial);
+static int keyspan_port_probe(struct usb_serial_port *port);
+static int keyspan_port_remove(struct usb_serial_port *port);
 static int  keyspan_write_room		(struct tty_struct *tty);
 
 static int  keyspan_write		(struct tty_struct *tty,
@@ -562,6 +564,8 @@ static struct usb_serial_driver keyspan_
 	.attach			= keyspan_startup,
 	.disconnect		= keyspan_disconnect,
 	.release		= keyspan_release,
+	.port_probe		= keyspan_port_probe,
+	.port_remove		= keyspan_port_remove,
 };
 
 static struct usb_serial_driver keyspan_2port_device = {
@@ -584,6 +588,8 @@ static struct usb_serial_driver keyspan_
 	.attach			= keyspan_startup,
 	.disconnect		= keyspan_disconnect,
 	.release		= keyspan_release,
+	.port_probe		= keyspan_port_probe,
+	.port_remove		= keyspan_port_remove,
 };
 
 static struct usb_serial_driver keyspan_4port_device = {
@@ -606,6 +612,8 @@ static struct usb_serial_driver keyspan_
 	.attach			= keyspan_startup,
 	.disconnect		= keyspan_disconnect,
 	.release		= keyspan_release,
+	.port_probe		= keyspan_port_probe,
+	.port_remove		= keyspan_port_remove,
 };
 
 static struct usb_serial_driver * const serial_drivers[] = {

[ 050/101] USB: omninet: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit feffa7ca6008ab859dd7ab7448a5a899bf0aa98f upstream.

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/omninet.c |   36 ++++++++++++++++++------------------
 1 file changed, 18 insertions(+), 18 deletions(-)

--- a/drivers/usb/serial/omninet.c
+++ b/drivers/usb/serial/omninet.c
@@ -46,8 +46,8 @@ static int  omninet_write(struct tty_str
 				const unsigned char *buf, int count);
 static int  omninet_write_room(struct tty_struct *tty);
 static void omninet_disconnect(struct usb_serial *serial);
-static void omninet_release(struct usb_serial *serial);
-static int omninet_attach(struct usb_serial *serial);
+static int omninet_port_probe(struct usb_serial_port *port);
+static int omninet_port_remove(struct usb_serial_port *port);
 
 static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(ZYXEL_VENDOR_ID, ZYXEL_OMNINET_ID) },
@@ -64,7 +64,8 @@ static struct usb_serial_driver zyxel_om
 	.description =		"ZyXEL - omni.net lcd plus usb",
 	.id_table =		id_table,
 	.num_ports =		1,
-	.attach =		omninet_attach,
+	.port_probe =		omninet_port_probe,
+	.port_remove =		omninet_port_remove,
 	.open =			omninet_open,
 	.close =		omninet_close,
 	.write =		omninet_write,
@@ -72,7 +73,6 @@ static struct usb_serial_driver zyxel_om
 	.read_bulk_callback =	omninet_read_bulk_callback,
 	.write_bulk_callback =	omninet_write_bulk_callback,
 	.disconnect =		omninet_disconnect,
-	.release =		omninet_release,
 };
 
 static struct usb_serial_driver * const serial_drivers[] = {
@@ -114,18 +114,26 @@ struct omninet_data {
 	__u8	od_outseq;	/* Sequence number for bulk_out URBs */
 };
 
-static int omninet_attach(struct usb_serial *serial)
+static int omninet_port_probe(struct usb_serial_port *port)
 {
 	struct omninet_data *od;
-	struct usb_serial_port *port = serial->port[0];
 
 	od = kmalloc(sizeof(struct omninet_data), GFP_KERNEL);
-	if (!od) {
-		dev_err(&port->dev, "%s- kmalloc(%Zd) failed.\n",
-			__func__, sizeof(struct omninet_data));
+	if (!od)
 		return -ENOMEM;
-	}
+
 	usb_set_serial_port_data(port, od);
+
+	return 0;
+}
+
+static int omninet_port_remove(struct usb_serial_port *port)
+{
+	struct omninet_data *od;
+
+	od = usb_get_serial_port_data(port);
+	kfree(od);
+
 	return 0;
 }
 
@@ -291,14 +299,6 @@ static void omninet_disconnect(struct us
 	usb_kill_urb(wport->write_urb);
 }
 
-
-static void omninet_release(struct usb_serial *serial)
-{
-	struct usb_serial_port *port = serial->port[0];
-
-	kfree(usb_get_serial_port_data(port));
-}
-
 module_usb_serial_driver(serial_drivers, id_table);
 
 MODULE_AUTHOR(DRIVER_AUTHOR);

[ 051/101] USB: qcserial: fix interface-data memory leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 961be09e1ead58509ed4bed0d5819a15d8613d8d upstream.

Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/qcserial.c |   31 ++++++++++++++++---------------
 1 file changed, 16 insertions(+), 15 deletions(-)

--- a/drivers/usb/serial/qcserial.c
+++ b/drivers/usb/serial/qcserial.c
@@ -140,7 +140,6 @@ MODULE_DEVICE_TABLE(usb, id_table);
 
 static int qcprobe(struct usb_serial *serial, const struct usb_device_id *id)
 {
-	struct usb_wwan_intf_private *data;
 	struct usb_host_interface *intf = serial->interface->cur_altsetting;
 	struct device *dev = &serial->dev->dev;
 	int retval = -ENODEV;
@@ -156,13 +155,6 @@ static int qcprobe(struct usb_serial *se
 	ifnum = intf->desc.bInterfaceNumber;
 	dev_dbg(dev, "This Interface = %d\n", ifnum);
 
-	data = kzalloc(sizeof(struct usb_wwan_intf_private),
-					 GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
-
-	spin_lock_init(&data->susp_lock);
-
 	if (nintf == 1) {
 		/* QDL mode */
 		/* Gobi 2000 has a single altsetting, older ones have two */
@@ -255,20 +247,28 @@ done:
 		}
 	}
 
-	/* Set serial->private if not returning error */
-	if (retval == 0)
-		usb_set_serial_data(serial, data);
-	else
-		kfree(data);
-
 	return retval;
 }
 
+static int qc_attach(struct usb_serial *serial)
+{
+	struct usb_wwan_intf_private *data;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	spin_lock_init(&data->susp_lock);
+
+	usb_set_serial_data(serial, data);
+
+	return 0;
+}
+
 static void qc_release(struct usb_serial *serial)
 {
 	struct usb_wwan_intf_private *priv = usb_get_serial_data(serial);
 
-	/* Free the private data allocated in qcprobe */
 	usb_set_serial_data(serial, NULL);
 	kfree(priv);
 }
@@ -287,6 +287,7 @@ static struct usb_serial_driver qcdevice
 	.write		     = usb_wwan_write,
 	.write_room	     = usb_wwan_write_room,
 	.chars_in_buffer     = usb_wwan_chars_in_buffer,
+	.attach              = qc_attach,
 	.release	     = qc_release,
 	.port_probe          = usb_wwan_port_probe,
 	.port_remove	     = usb_wwan_port_remove,

[ 052/101] USB: whiteheat: fix memory leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit c129197c99550d356cf5f69b046994dd53cd1b9d upstream.

Make sure command buffer is deallocated in case of errors during attach.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/whiteheat.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -405,6 +405,7 @@ no_firmware:
 		"%s: please contact support@connecttech.com\n",
 		serial->type->description);
 	kfree(result);
+	kfree(command);
 	return -ENODEV;
 
 no_command_private:

[ 053/101] USB: whiteheat: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit c467206ed6bcce26c83d0435612cc4fee2527305 upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the fifth port (command port) is never registered as a
port device and thus should be handled in attach and release.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/whiteheat.c |   59 ++++++++++++++++++-----------------------
 1 file changed, 26 insertions(+), 33 deletions(-)

--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -86,6 +86,8 @@ static int  whiteheat_firmware_attach(st
 /* function prototypes for the Connect Tech WhiteHEAT serial converter */
 static int  whiteheat_attach(struct usb_serial *serial);
 static void whiteheat_release(struct usb_serial *serial);
+static int  whiteheat_port_probe(struct usb_serial_port *port);
+static int  whiteheat_port_remove(struct usb_serial_port *port);
 static int  whiteheat_open(struct tty_struct *tty,
 			struct usb_serial_port *port);
 static void whiteheat_close(struct usb_serial_port *port);
@@ -120,6 +122,8 @@ static struct usb_serial_driver whitehea
 	.num_ports =		4,
 	.attach =		whiteheat_attach,
 	.release =		whiteheat_release,
+	.port_probe =		whiteheat_port_probe,
+	.port_remove =		whiteheat_port_remove,
 	.open =			whiteheat_open,
 	.close =		whiteheat_close,
 	.ioctl =		whiteheat_ioctl,
@@ -290,15 +294,12 @@ static int whiteheat_attach(struct usb_s
 {
 	struct usb_serial_port *command_port;
 	struct whiteheat_command_private *command_info;
-	struct usb_serial_port *port;
-	struct whiteheat_private *info;
 	struct whiteheat_hw_info *hw_info;
 	int pipe;
 	int ret;
 	int alen;
 	__u8 *command;
 	__u8 *result;
-	int i;
 
 	command_port = serial->port[COMMAND_PORT];
 
@@ -357,22 +358,6 @@ static int whiteheat_attach(struct usb_s
 		 serial->type->description,
 		 hw_info->sw_major_rev, hw_info->sw_minor_rev);
 
-	for (i = 0; i < serial->num_ports; i++) {
-		port = serial->port[i];
-
-		info = kmalloc(sizeof(struct whiteheat_private), GFP_KERNEL);
-		if (info == NULL) {
-			dev_err(&port->dev,
-				"%s: Out of memory for port structures\n",
-				serial->type->description);
-			goto no_private;
-		}
-
-		info->mcr = 0;
-
-		usb_set_serial_port_data(port, info);
-	}
-
 	command_info = kmalloc(sizeof(struct whiteheat_command_private),
 								GFP_KERNEL);
 	if (command_info == NULL) {
@@ -409,13 +394,6 @@ no_firmware:
 	return -ENODEV;
 
 no_command_private:
-	for (i = serial->num_ports - 1; i >= 0; i--) {
-		port = serial->port[i];
-		info = usb_get_serial_port_data(port);
-		kfree(info);
-no_private:
-		;
-	}
 	kfree(result);
 no_result_buffer:
 	kfree(command);
@@ -423,21 +401,36 @@ no_command_buffer:
 	return -ENOMEM;
 }
 
-
 static void whiteheat_release(struct usb_serial *serial)
 {
 	struct usb_serial_port *command_port;
-	struct whiteheat_private *info;
-	int i;
 
 	/* free up our private data for our command port */
 	command_port = serial->port[COMMAND_PORT];
 	kfree(usb_get_serial_port_data(command_port));
+}
 
-	for (i = 0; i < serial->num_ports; i++) {
-		info = usb_get_serial_port_data(serial->port[i]);
-		kfree(info);
-	}
+static int whiteheat_port_probe(struct usb_serial_port *port)
+{
+	struct whiteheat_private *info;
+
+	info = kzalloc(sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	usb_set_serial_port_data(port, info);
+
+	return 0;
+}
+
+static int whiteheat_port_remove(struct usb_serial_port *port)
+{
+	struct whiteheat_private *info;
+
+	info = usb_get_serial_port_data(port);
+	kfree(info);
+
+	return 0;
 }
 
 static int whiteheat_open(struct tty_struct *tty, struct usb_serial_port *port)

[ 054/101] USB: opticon: fix DMA from stack

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit ea0dbebffe118724cd4df7d9b071ea8ee48d48f0 upstream.

Make sure to allocate the control-message buffer dynamically as some
platforms cannot do DMA from stack.

Note that only the first byte of the old buffer was used.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/opticon.c |    7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

--- a/drivers/usb/serial/opticon.c
+++ b/drivers/usb/serial/opticon.c
@@ -158,7 +158,11 @@ static int send_control_msg(struct usb_s
 {
 	struct usb_serial *serial = port->serial;
 	int retval;
-	u8 buffer[2];
+	u8 *buffer;
+
+	buffer = kzalloc(1, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
 
 	buffer[0] = val;
 	/* Send the message to the vendor control endpoint
@@ -167,6 +171,7 @@ static int send_control_msg(struct usb_s
 				requesttype,
 				USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE,
 				0, 0, buffer, 1, 0);
+	kfree(buffer);
 
 	return retval;
 }

[ 055/101] USB: opticon: fix memory leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit acbf0e5263de563e25f7c104868e4490b9e72b13 upstream.

Fix memory leak in write error path.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/opticon.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/drivers/usb/serial/opticon.c
+++ b/drivers/usb/serial/opticon.c
@@ -289,7 +289,7 @@ static int opticon_write(struct tty_stru
 	if (!dr) {
 		dev_err(&port->dev, "out of memory\n");
 		count = -ENOMEM;
-		goto error;
+		goto error_no_dr;
 	}
 
 	dr->bRequestType = USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT;
@@ -319,6 +319,8 @@ static int opticon_write(struct tty_stru
 
 	return count;
 error:
+	kfree(dr);
+error_no_dr:
 	usb_free_urb(urb);
 error_no_urb:
 	kfree(buffer);

[ 056/101] USB: metro-usb: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 50dde8686eec41bf3d7cbec7a6f76c073ab01903 upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the call to metrousb_clean (close) in shutdown was redundant.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/metro-usb.c |   50 ++++++++++-------------------------------
 1 file changed, 13 insertions(+), 37 deletions(-)

--- a/drivers/usb/serial/metro-usb.c
+++ b/drivers/usb/serial/metro-usb.c
@@ -280,51 +280,27 @@ static int metrousb_set_modem_ctrl(struc
 	return retval;
 }
 
-static void metrousb_shutdown(struct usb_serial *serial)
+static int metrousb_port_probe(struct usb_serial_port *port)
 {
-	int i = 0;
+	struct metrousb_private *metro_priv;
 
-	dev_dbg(&serial->dev->dev, "%s\n", __func__);
+	metro_priv = kzalloc(sizeof(*metro_priv), GFP_KERNEL);
+	if (!metro_priv)
+		return -ENOMEM;
 
-	/* Stop reading and writing on all ports. */
-	for (i = 0; i < serial->num_ports; ++i) {
-		/* Close any open urbs. */
-		metrousb_cleanup(serial->port[i]);
+	spin_lock_init(&metro_priv->lock);
 
-		/* Free memory. */
-		kfree(usb_get_serial_port_data(serial->port[i]));
-		usb_set_serial_port_data(serial->port[i], NULL);
+	usb_set_serial_port_data(port, metro_priv);
 
-		dev_dbg(&serial->dev->dev, "%s - freed port number=%d\n",
-			__func__, serial->port[i]->number);
-	}
+	return 0;
 }
 
-static int metrousb_startup(struct usb_serial *serial)
+static int metrousb_port_remove(struct usb_serial_port *port)
 {
 	struct metrousb_private *metro_priv;
-	struct usb_serial_port *port;
-	int i = 0;
-
-	dev_dbg(&serial->dev->dev, "%s\n", __func__);
 
-	/* Loop through the serial ports setting up the private structures.
-	 * Currently we only use one port. */
-	for (i = 0; i < serial->num_ports; ++i) {
-		port = serial->port[i];
-
-		/* Declare memory. */
-		metro_priv = kzalloc(sizeof(struct metrousb_private), GFP_KERNEL);
-		if (!metro_priv)
-			return -ENOMEM;
-
-		/* Initialize memory. */
-		spin_lock_init(&metro_priv->lock);
-		usb_set_serial_port_data(port, metro_priv);
-
-		dev_dbg(&serial->dev->dev, "%s - port number=%d\n ",
-			__func__, port->number);
-	}
+	metro_priv = usb_get_serial_port_data(port);
+	kfree(metro_priv);
 
 	return 0;
 }
@@ -423,8 +399,8 @@ static struct usb_serial_driver metrousb
 	.close			= metrousb_cleanup,
 	.read_int_callback	= metrousb_read_int_callback,
 	.write_int_callback	= metrousb_write_int_callback,
-	.attach			= metrousb_startup,
-	.release		= metrousb_shutdown,
+	.port_probe		= metrousb_port_probe,
+	.port_remove		= metrousb_port_remove,
 	.throttle		= metrousb_throttle,
 	.unthrottle		= metrousb_unthrottle,
 	.tiocmget		= metrousb_tiocmget,

[ 057/101] USB: metro-usb: fix io after disconnect

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 2ee44fbeac92c36e53779a57ee84cfee1affe418 upstream.

Make sure no control urb is submitted during close after a disconnect by
checking the disconnected flag.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/metro-usb.c |   13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

--- a/drivers/usb/serial/metro-usb.c
+++ b/drivers/usb/serial/metro-usb.c
@@ -188,16 +188,13 @@ static void metrousb_cleanup(struct usb_
 {
 	dev_dbg(&port->dev, "%s\n", __func__);
 
-	if (port->serial->dev) {
-		/* Shutdown any interrupt in urbs. */
-		if (port->interrupt_in_urb) {
-			usb_unlink_urb(port->interrupt_in_urb);
-			usb_kill_urb(port->interrupt_in_urb);
-		}
+	usb_unlink_urb(port->interrupt_in_urb);
+	usb_kill_urb(port->interrupt_in_urb);
 
-		/* Send deactivate cmd to device */
+	mutex_lock(&port->serial->disc_mutex);
+	if (!port->serial->disconnected)
 		metrousb_send_unidirectional_cmd(UNI_CMD_CLOSE, port);
-	}
+	mutex_unlock(&port->serial->disc_mutex);
 }
 
 static int metrousb_open(struct tty_struct *tty, struct usb_serial_port *port)

[ 058/101] USB: mos7720: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 4230af572f95b3115bba1ee6fb95681f3851ab26 upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that this patch also fixes a second port-data memory leak in the
error path of attach, should parallel-port initialisation fail.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mos7720.c |   62 ++++++++++++++++++++++---------------------
 1 file changed, 32 insertions(+), 30 deletions(-)

--- a/drivers/usb/serial/mos7720.c
+++ b/drivers/usb/serial/mos7720.c
@@ -2023,9 +2023,7 @@ static int mos7720_ioctl(struct tty_stru
 
 static int mos7720_startup(struct usb_serial *serial)
 {
-	struct moschip_port *mos7720_port;
 	struct usb_device *dev;
-	int i;
 	char data;
 	u16 product;
 	int ret_val;
@@ -2063,29 +2061,6 @@ static int mos7720_startup(struct usb_se
 		serial->port[1]->interrupt_in_buffer = NULL;
 	}
 
-
-	/* set up serial port private structures */
-	for (i = 0; i < serial->num_ports; ++i) {
-		mos7720_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL);
-		if (mos7720_port == NULL) {
-			dev_err(&dev->dev, "%s - Out of memory\n", __func__);
-			return -ENOMEM;
-		}
-
-		/* Initialize all port interrupt end point to port 0 int
-		 * endpoint.  Our device has only one interrupt endpoint
-		 * common to all ports */
-		serial->port[i]->interrupt_in_endpointAddress =
-				serial->port[0]->interrupt_in_endpointAddress;
-
-		mos7720_port->port = serial->port[i];
-		usb_set_serial_port_data(serial->port[i], mos7720_port);
-
-		dbg("port number is %d", serial->port[i]->number);
-		dbg("serial number is %d", serial->minor);
-	}
-
-
 	/* setting configuration feature to one */
 	usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
 			(__u8)0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5*HZ);
@@ -2113,8 +2088,6 @@ static int mos7720_startup(struct usb_se
 
 static void mos7720_release(struct usb_serial *serial)
 {
-	int i;
-
 #ifdef CONFIG_USB_SERIAL_MOS7715_PARPORT
 	/* close the parallel port */
 
@@ -2153,9 +2126,36 @@ static void mos7720_release(struct usb_s
 		kref_put(&mos_parport->ref_count, destroy_mos_parport);
 	}
 #endif
-	/* free private structure allocated for serial port */
-	for (i = 0; i < serial->num_ports; ++i)
-		kfree(usb_get_serial_port_data(serial->port[i]));
+}
+
+static int mos7720_port_probe(struct usb_serial_port *port)
+{
+	struct moschip_port *mos7720_port;
+
+	mos7720_port = kzalloc(sizeof(*mos7720_port), GFP_KERNEL);
+	if (!mos7720_port)
+		return -ENOMEM;
+
+	/* Initialize all port interrupt end point to port 0 int endpoint.
+	 * Our device has only one interrupt endpoint common to all ports.
+	 */
+	port->interrupt_in_endpointAddress =
+		port->serial->port[0]->interrupt_in_endpointAddress;
+	mos7720_port->port = port;
+
+	usb_set_serial_port_data(port, mos7720_port);
+
+	return 0;
+}
+
+static int mos7720_port_remove(struct usb_serial_port *port)
+{
+	struct moschip_port *mos7720_port;
+
+	mos7720_port = usb_get_serial_port_data(port);
+	kfree(mos7720_port);
+
+	return 0;
 }
 
 static struct usb_serial_driver moschip7720_2port_driver = {
@@ -2173,6 +2173,8 @@ static struct usb_serial_driver moschip7
 	.probe			= mos77xx_probe,
 	.attach			= mos7720_startup,
 	.release		= mos7720_release,
+	.port_probe		= mos7720_port_probe,
+	.port_remove		= mos7720_port_remove,
 	.ioctl			= mos7720_ioctl,
 	.tiocmget		= mos7720_tiocmget,
 	.tiocmset		= mos7720_tiocmset,

[ 059/101] USB: quatech2: fix memory leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit b8a0055050b6294826171641b182c09f78f4cc63 upstream.

Fix memory leak in attach error path where the read urb was never freed.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/quatech2.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/usb/serial/quatech2.c
+++ b/drivers/usb/serial/quatech2.c
@@ -825,6 +825,7 @@ static int qt2_setup_urbs(struct usb_ser
 	if (status != 0) {
 		dev_err(&serial->dev->dev,
 			"%s - submit read urb failed %i\n", __func__, status);
+		usb_free_urb(serial_priv->read_urb);
 		return status;
 	}
 

[ 060/101] USB: quatech2: fix port-data memory leaks

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 40d04738491d7ac1aa708ba434ff3480ec9e1b96 upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that this also fixes memory leaks in the error path of attach where
the write urbs were not freed on errors.

Make sure all interface-data deallocation is done in release by moving
the read urb deallocation from disconnect.

Note that the write urb is killed during close so that the call in
disconnect was superfluous.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/quatech2.c |  121 +++++++++++++++++-------------------------
 1 file changed, 51 insertions(+), 70 deletions(-)

--- a/drivers/usb/serial/quatech2.c
+++ b/drivers/usb/serial/quatech2.c
@@ -145,12 +145,12 @@ static void qt2_read_bulk_callback(struc
 
 static void qt2_release(struct usb_serial *serial)
 {
-	int i;
+	struct qt2_serial_private *serial_priv;
 
-	kfree(usb_get_serial_data(serial));
+	serial_priv = usb_get_serial_data(serial);
 
-	for (i = 0; i < serial->num_ports; i++)
-		kfree(usb_get_serial_port_data(serial->port[i]));
+	usb_free_urb(serial_priv->read_urb);
+	kfree(serial_priv);
 }
 
 static inline int calc_baud_divisor(int baudrate)
@@ -466,21 +466,9 @@ static void qt2_close(struct usb_serial_
 static void qt2_disconnect(struct usb_serial *serial)
 {
 	struct qt2_serial_private *serial_priv = usb_get_serial_data(serial);
-	struct qt2_port_private *port_priv;
-	int i;
 
 	if (serial_priv->read_urb->status == -EINPROGRESS)
 		usb_kill_urb(serial_priv->read_urb);
-
-	usb_free_urb(serial_priv->read_urb);
-
-	for (i = 0; i < serial->num_ports; i++) {
-		port_priv = usb_get_serial_port_data(serial->port[i]);
-
-		if (port_priv->write_urb->status == -EINPROGRESS)
-			usb_kill_urb(port_priv->write_urb);
-		usb_free_urb(port_priv->write_urb);
-	}
 }
 
 static int get_serial_info(struct usb_serial_port *port,
@@ -775,11 +763,9 @@ static void qt2_read_bulk_callback(struc
 
 static int qt2_setup_urbs(struct usb_serial *serial)
 {
-	struct usb_serial_port *port;
 	struct usb_serial_port *port0;
 	struct qt2_serial_private *serial_priv;
-	struct qt2_port_private *port_priv;
-	int pcount, status;
+	int status;
 
 	port0 = serial->port[0];
 
@@ -797,30 +783,6 @@ static int qt2_setup_urbs(struct usb_ser
 			  sizeof(serial_priv->read_buffer),
 			  qt2_read_bulk_callback, serial);
 
-	/* setup write_urb for each port */
-	for (pcount = 0; pcount < serial->num_ports; pcount++) {
-
-		port = serial->port[pcount];
-		port_priv = usb_get_serial_port_data(port);
-
-		port_priv->write_urb = usb_alloc_urb(0, GFP_KERNEL);
-		if (!port_priv->write_urb) {
-			dev_err(&serial->dev->dev,
-				"failed to alloc write_urb for port %i\n",
-				pcount);
-			return -ENOMEM;
-		}
-
-		usb_fill_bulk_urb(port_priv->write_urb,
-				  serial->dev,
-				  usb_sndbulkpipe(serial->dev,
-						  port0->
-						  bulk_out_endpointAddress),
-				  port_priv->write_buffer,
-				  sizeof(port_priv->write_buffer),
-				  qt2_write_bulk_callback, port);
-	}
-
 	status = usb_submit_urb(serial_priv->read_urb, GFP_KERNEL);
 	if (status != 0) {
 		dev_err(&serial->dev->dev,
@@ -830,14 +792,12 @@ static int qt2_setup_urbs(struct usb_ser
 	}
 
 	return 0;
-
 }
 
 static int qt2_attach(struct usb_serial *serial)
 {
 	struct qt2_serial_private *serial_priv;
-	struct qt2_port_private *port_priv;
-	int status, pcount;
+	int status;
 
 	/* power on unit */
 	status = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
@@ -857,26 +817,6 @@ static int qt2_attach(struct usb_serial
 
 	usb_set_serial_data(serial, serial_priv);
 
-	for (pcount = 0; pcount < serial->num_ports; pcount++) {
-		port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
-		if (!port_priv) {
-			dev_err(&serial->dev->dev,
-				"%s- kmalloc(%Zd) failed.\n", __func__,
-				sizeof(*port_priv));
-			pcount--;
-			status = -ENOMEM;
-			goto attach_failed;
-		}
-
-		spin_lock_init(&port_priv->lock);
-		spin_lock_init(&port_priv->urb_lock);
-		init_waitqueue_head(&port_priv->delta_msr_wait);
-
-		port_priv->port = serial->port[pcount];
-
-		usb_set_serial_port_data(serial->port[pcount], port_priv);
-	}
-
 	status = qt2_setup_urbs(serial);
 	if (status != 0)
 		goto attach_failed;
@@ -884,14 +824,53 @@ static int qt2_attach(struct usb_serial
 	return 0;
 
 attach_failed:
-	for (/* empty */; pcount >= 0; pcount--) {
-		port_priv = usb_get_serial_port_data(serial->port[pcount]);
-		kfree(port_priv);
-	}
 	kfree(serial_priv);
 	return status;
 }
 
+static int qt2_port_probe(struct usb_serial_port *port)
+{
+	struct usb_serial *serial = port->serial;
+	struct qt2_port_private *port_priv;
+	u8 bEndpointAddress;
+
+	port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
+	if (!port_priv)
+		return -ENOMEM;
+
+	spin_lock_init(&port_priv->lock);
+	spin_lock_init(&port_priv->urb_lock);
+	init_waitqueue_head(&port_priv->delta_msr_wait);
+	port_priv->port = port;
+
+	port_priv->write_urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!port_priv->write_urb) {
+		kfree(port_priv);
+		return -ENOMEM;
+	}
+	bEndpointAddress = serial->port[0]->bulk_out_endpointAddress;
+	usb_fill_bulk_urb(port_priv->write_urb, serial->dev,
+				usb_sndbulkpipe(serial->dev, bEndpointAddress),
+				port_priv->write_buffer,
+				sizeof(port_priv->write_buffer),
+				qt2_write_bulk_callback, port);
+
+	usb_set_serial_port_data(port, port_priv);
+
+	return 0;
+}
+
+static int qt2_port_remove(struct usb_serial_port *port)
+{
+	struct qt2_port_private *port_priv;
+
+	port_priv = usb_get_serial_port_data(port);
+	usb_free_urb(port_priv->write_urb);
+	kfree(port_priv);
+
+	return 0;
+}
+
 static int qt2_tiocmget(struct tty_struct *tty)
 {
 	struct usb_serial_port *port = tty->driver_data;
@@ -1130,6 +1109,8 @@ static struct usb_serial_driver qt2_devi
 	.attach              = qt2_attach,
 	.release             = qt2_release,
 	.disconnect          = qt2_disconnect,
+	.port_probe          = qt2_port_probe,
+	.port_remove         = qt2_port_remove,
 	.dtr_rts             = qt2_dtr_rts,
 	.break_ctl           = qt2_break_ctl,
 	.tiocmget            = qt2_tiocmget,

[ 061/101] USB: quatech2: fix close and disconnect urb handling

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 8e512ab0b675da20e023439a5811e3f2554e6852 upstream.

Kill urbs unconditionally at close and disconnect.

Note that URB status is not valid outside of completion handler.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/quatech2.c |    6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

--- a/drivers/usb/serial/quatech2.c
+++ b/drivers/usb/serial/quatech2.c
@@ -425,8 +425,7 @@ static void qt2_close(struct usb_serial_
 	port_priv->is_open = false;
 
 	spin_lock_irqsave(&port_priv->urb_lock, flags);
-	if (port_priv->write_urb->status == -EINPROGRESS)
-		usb_kill_urb(port_priv->write_urb);
+	usb_kill_urb(port_priv->write_urb);
 	port_priv->urb_in_use = false;
 	spin_unlock_irqrestore(&port_priv->urb_lock, flags);
 
@@ -467,8 +466,7 @@ static void qt2_disconnect(struct usb_se
 {
 	struct qt2_serial_private *serial_priv = usb_get_serial_data(serial);
 
-	if (serial_priv->read_urb->status == -EINPROGRESS)
-		usb_kill_urb(serial_priv->read_urb);
+	usb_kill_urb(serial_priv->read_urb);
 }
 
 static int get_serial_info(struct usb_serial_port *port,

[ 062/101] USB: quatech2: fix io after disconnect

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 2f0295adf6438188c4cd0868f2b1976a2b034e1d upstream.

Make sure no control urb is submitted during close after a disconnect by
checking the disconnected flag.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/quatech2.c |    7 +++++++
 1 file changed, 7 insertions(+)

--- a/drivers/usb/serial/quatech2.c
+++ b/drivers/usb/serial/quatech2.c
@@ -429,6 +429,12 @@ static void qt2_close(struct usb_serial_
 	port_priv->urb_in_use = false;
 	spin_unlock_irqrestore(&port_priv->urb_lock, flags);
 
+	mutex_lock(&port->serial->disc_mutex);
+	if (port->serial->disconnected) {
+		mutex_unlock(&port->serial->disc_mutex);
+		return;
+	}
+
 	/* flush the port transmit buffer */
 	i = usb_control_msg(serial->dev,
 			    usb_rcvctrlpipe(serial->dev, 0),
@@ -460,6 +466,7 @@ static void qt2_close(struct usb_serial_
 		dev_err(&port->dev, "%s - close port failed %i\n",
 			__func__, i);
 
+	mutex_unlock(&port->serial->disc_mutex);
 }
 
 static void qt2_disconnect(struct usb_serial *serial)

[ 063/101] USB: serial: Fix memory leak in sierra_release()

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>

commit f7bc5051667b74c3861f79eed98c60d5c3b883f7 upstream.

I found a memory leak in sierra_release() (well sierra_probe() I guess)
that looses 8 bytes each time the driver releases a device.

Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/sierra.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -961,6 +961,7 @@ static void sierra_release(struct usb_se
 			continue;
 		kfree(portdata);
 	}
+	kfree(serial->private);
 }
 
 #ifdef CONFIG_PM

[ 064/101] USB: sierra: fix memory leak in attach error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 7e41f9bcdd2e813ea2a3c40db291d87ea06b559f upstream.

Make sure port private data is deallocated on errors in attach.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/sierra.c |    9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -907,7 +907,7 @@ static int sierra_startup(struct usb_ser
 			dev_dbg(&port->dev, "%s: kmalloc for "
 				"sierra_port_private (%d) failed!\n",
 				__func__, i);
-			return -ENOMEM;
+			goto err;
 		}
 		spin_lock_init(&portdata->lock);
 		init_usb_anchor(&portdata->active);
@@ -944,6 +944,13 @@ static int sierra_startup(struct usb_ser
 	}
 
 	return 0;
+err:
+	for (--i; i >= 0; --i) {
+		portdata = usb_get_serial_port_data(serial->port[i]);
+		kfree(portdata);
+	}
+
+	return -ENOMEM;
 }
 
 static void sierra_release(struct usb_serial *serial)

[ 065/101] USB: sierra: fix memory leak in probe error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 084817d79399ab5ccab2f90a148b0369912a8369 upstream.

Move interface data allocation to attach so that it is deallocated on
errors in usb-serial probe.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/sierra.c |   16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -162,7 +162,6 @@ static int sierra_probe(struct usb_seria
 {
 	int result = 0;
 	struct usb_device *udev;
-	struct sierra_intf_private *data;
 	u8 ifnum;
 
 	udev = serial->dev;
@@ -189,11 +188,6 @@ static int sierra_probe(struct usb_seria
 		return -ENODEV;
 	}
 
-	data = serial->private = kzalloc(sizeof(struct sierra_intf_private), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
-	spin_lock_init(&data->susp_lock);
-
 	return result;
 }
 
@@ -887,11 +881,20 @@ static void sierra_dtr_rts(struct usb_se
 static int sierra_startup(struct usb_serial *serial)
 {
 	struct usb_serial_port *port;
+	struct sierra_intf_private *intfdata;
 	struct sierra_port_private *portdata;
 	struct sierra_iface_info *himemoryp = NULL;
 	int i;
 	u8 ifnum;
 
+	intfdata = kzalloc(sizeof(*intfdata), GFP_KERNEL);
+	if (!intfdata)
+		return -ENOMEM;
+
+	spin_lock_init(&intfdata->susp_lock);
+
+	usb_set_serial_data(serial, intfdata);
+
 	/* Set Device mode to D0 */
 	sierra_set_power_state(serial->dev, 0x0000);
 
@@ -949,6 +952,7 @@ err:
 		portdata = usb_get_serial_port_data(serial->port[i]);
 		kfree(portdata);
 	}
+	kfree(intfdata);
 
 	return -ENOMEM;
 }

[ 066/101] USB: sierra: fix port-data memory leak

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit f525c05babc7938cc1d4236550fd8a659fb05960 upstream.

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d0631001288 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note also that urb-count for multi-port interfaces has not been changed
even though the usb-serial port number is now determined from the port
and interface minor numbers.

Compile-only tested.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/sierra.c |  127 ++++++++++++++++++++------------------------
 1 file changed, 59 insertions(+), 68 deletions(-)

--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -880,12 +880,7 @@ static void sierra_dtr_rts(struct usb_se
 
 static int sierra_startup(struct usb_serial *serial)
 {
-	struct usb_serial_port *port;
 	struct sierra_intf_private *intfdata;
-	struct sierra_port_private *portdata;
-	struct sierra_iface_info *himemoryp = NULL;
-	int i;
-	u8 ifnum;
 
 	intfdata = kzalloc(sizeof(*intfdata), GFP_KERNEL);
 	if (!intfdata)
@@ -902,77 +897,71 @@ static int sierra_startup(struct usb_ser
 	if (nmea)
 		sierra_vsc_set_nmea(serial->dev, 1);
 
-	/* Now setup per port private data */
-	for (i = 0; i < serial->num_ports; i++) {
-		port = serial->port[i];
-		portdata = kzalloc(sizeof(*portdata), GFP_KERNEL);
-		if (!portdata) {
-			dev_dbg(&port->dev, "%s: kmalloc for "
-				"sierra_port_private (%d) failed!\n",
-				__func__, i);
-			goto err;
-		}
-		spin_lock_init(&portdata->lock);
-		init_usb_anchor(&portdata->active);
-		init_usb_anchor(&portdata->delayed);
-		ifnum = i;
-		/* Assume low memory requirements */
-		portdata->num_out_urbs = N_OUT_URB;
-		portdata->num_in_urbs  = N_IN_URB;
-
-		/* Determine actual memory requirements */
-		if (serial->num_ports == 1) {
-			/* Get interface number for composite device */
-			ifnum = sierra_calc_interface(serial);
-			himemoryp =
-			    (struct sierra_iface_info *)&typeB_interface_list;
-			if (is_himemory(ifnum, himemoryp)) {
-				portdata->num_out_urbs = N_OUT_URB_HM;
-				portdata->num_in_urbs  = N_IN_URB_HM;
-			}
-		}
-		else {
-			himemoryp =
-			    (struct sierra_iface_info *)&typeA_interface_list;
-			if (is_himemory(i, himemoryp)) {
-				portdata->num_out_urbs = N_OUT_URB_HM;
-				portdata->num_in_urbs  = N_IN_URB_HM;
-			}
-		}
-		dev_dbg(&serial->dev->dev,
-			"Memory usage (urbs) interface #%d, in=%d, out=%d\n",
-			ifnum,portdata->num_in_urbs, portdata->num_out_urbs );
-		/* Set the port private data pointer */
-		usb_set_serial_port_data(port, portdata);
-	}
-
 	return 0;
-err:
-	for (--i; i >= 0; --i) {
-		portdata = usb_get_serial_port_data(serial->port[i]);
-		kfree(portdata);
-	}
-	kfree(intfdata);
-
-	return -ENOMEM;
 }
 
 static void sierra_release(struct usb_serial *serial)
 {
-	int i;
-	struct usb_serial_port *port;
+	struct sierra_intf_private *intfdata;
+
+	intfdata = usb_get_serial_data(serial);
+	kfree(intfdata);
+}
+
+static int sierra_port_probe(struct usb_serial_port *port)
+{
+	struct usb_serial *serial = port->serial;
 	struct sierra_port_private *portdata;
+	const struct sierra_iface_info *himemoryp;
+	u8 ifnum;
 
-	for (i = 0; i < serial->num_ports; ++i) {
-		port = serial->port[i];
-		if (!port)
-			continue;
-		portdata = usb_get_serial_port_data(port);
-		if (!portdata)
-			continue;
-		kfree(portdata);
+	portdata = kzalloc(sizeof(*portdata), GFP_KERNEL);
+	if (!portdata)
+		return -ENOMEM;
+
+	spin_lock_init(&portdata->lock);
+	init_usb_anchor(&portdata->active);
+	init_usb_anchor(&portdata->delayed);
+
+	/* Assume low memory requirements */
+	portdata->num_out_urbs = N_OUT_URB;
+	portdata->num_in_urbs  = N_IN_URB;
+
+	/* Determine actual memory requirements */
+	if (serial->num_ports == 1) {
+		/* Get interface number for composite device */
+		ifnum = sierra_calc_interface(serial);
+		himemoryp = &typeB_interface_list;
+	} else {
+		/* This is really the usb-serial port number of the interface
+		 * rather than the interface number.
+		 */
+		ifnum = port->number - serial->minor;
+		himemoryp = &typeA_interface_list;
+	}
+
+	if (is_himemory(ifnum, himemoryp)) {
+		portdata->num_out_urbs = N_OUT_URB_HM;
+		portdata->num_in_urbs  = N_IN_URB_HM;
 	}
-	kfree(serial->private);
+
+	dev_dbg(&port->dev,
+			"Memory usage (urbs) interface #%d, in=%d, out=%d\n",
+			ifnum, portdata->num_in_urbs, portdata->num_out_urbs);
+
+	usb_set_serial_port_data(port, portdata);
+
+	return 0;
+}
+
+static int sierra_port_remove(struct usb_serial_port *port)
+{
+	struct sierra_port_private *portdata;
+
+	portdata = usb_get_serial_port_data(port);
+	kfree(portdata);
+
+	return 0;
 }
 
 #ifdef CONFIG_PM
@@ -1076,6 +1065,8 @@ static struct usb_serial_driver sierra_d
 	.tiocmset          = sierra_tiocmset,
 	.attach            = sierra_startup,
 	.release           = sierra_release,
+	.port_probe        = sierra_port_probe,
+	.port_remove       = sierra_port_remove,
 	.suspend	   = sierra_suspend,
 	.resume		   = sierra_resume,
 	.read_int_callback = sierra_instat_callback,

[ 067/101] USB: mos7840: fix urb leak at release

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 65a4cdbb170e4ec1a7fa0e94936d47e24a17b0e8 upstream.

Make sure control urb is freed at release.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mos7840.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -2754,6 +2754,7 @@ static void mos7840_release(struct usb_s
 				del_timer_sync(&mos7840_port->led_timer1);
 				del_timer_sync(&mos7840_port->led_timer2);
 			}
+			usb_free_urb(mos7840_port->control_urb);
 			kfree(mos7840_port->ctrl_buf);
 			kfree(mos7840_port->dr);
 			kfree(mos7840_port);

[ 068/101] USB: mos7840: fix port-device leak in error path

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 3eb55cc4ed88eee3b5230f66abcdbd2a91639eda upstream.

The driver set the usb-serial port pointers to NULL on errors in attach,
effectively preventing usb-serial core from decrementing the port ref
counters and releasing the port devices and associated data.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mos7840.c |    1 -
 1 file changed, 1 deletion(-)

--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -2684,7 +2684,6 @@ error:
 		kfree(mos7840_port->ctrl_buf);
 		usb_free_urb(mos7840_port->control_urb);
 		kfree(mos7840_port);
-		serial->port[i] = NULL;
 	}
 	return status;
 }

[ 069/101] USB: mos7840: remove NULL-urb submission

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit 28c3ae9a8cf45f439c9a0779ebd0256e2ae72813 upstream.

The private int_urb is never allocated so the submission from the
control completion handler will always fail. Remove this odd piece of
broken code.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mos7840.c |   15 +--------------
 1 file changed, 1 insertion(+), 14 deletions(-)

--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -218,7 +218,6 @@ struct moschip_port {
 	int port_num;		/*Actual port number in the device(1,2,etc) */
 	struct urb *write_urb;	/* write URB for this port */
 	struct urb *read_urb;	/* read URB for this port */
-	struct urb *int_urb;
 	__u8 shadowLCR;		/* last LCR value received */
 	__u8 shadowMCR;		/* last MCR value received */
 	char open;
@@ -493,7 +492,6 @@ static void mos7840_control_callback(str
 	unsigned char *data;
 	struct moschip_port *mos7840_port;
 	__u8 regval = 0x0;
-	int result = 0;
 	int status = urb->status;
 
 	mos7840_port = urb->context;
@@ -512,7 +510,7 @@ static void mos7840_control_callback(str
 	default:
 		dbg("%s - nonzero urb status received: %d", __func__,
 		    status);
-		goto exit;
+		return;
 	}
 
 	dbg("%s urb buffer size is %d", __func__, urb->actual_length);
@@ -525,17 +523,6 @@ static void mos7840_control_callback(str
 		mos7840_handle_new_msr(mos7840_port, regval);
 	else if (mos7840_port->MsrLsr == 1)
 		mos7840_handle_new_lsr(mos7840_port, regval);
-
-exit:
-	spin_lock(&mos7840_port->pool_lock);
-	if (!mos7840_port->zombie)
-		result = usb_submit_urb(mos7840_port->int_urb, GFP_ATOMIC);
-	spin_unlock(&mos7840_port->pool_lock);
-	if (result) {
-		dev_err(&urb->dev->dev,
-			"%s - Error %d submitting interrupt urb\n",
-			__func__, result);
-	}
 }
 
 static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg,

[ 070/101] USB: mos7840: remove invalid disconnect handling

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hovold <jhovold@gmail.com>

commit e681b66f2e19fadbe8a7e2a17900978cb6bc921f upstream.

Remove private zombie flag used to signal disconnect and to prevent
control urb from being submitted from interrupt urb completion handler.

The control urb will not be re-submitted as both the control urb and the
interrupt urb is killed on disconnect.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/serial/mos7840.c |   13 +------------
 1 file changed, 1 insertion(+), 12 deletions(-)

--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -222,7 +222,6 @@ struct moschip_port {
 	__u8 shadowMCR;		/* last MCR value received */
 	char open;
 	char open_ports;
-	char zombie;
 	wait_queue_head_t wait_chase;	/* for handling sleeping while waiting for chase to finish */
 	wait_queue_head_t delta_msr_wait;	/* for handling sleeping while waiting for msr change to happen */
 	int delta_msr_cond;
@@ -691,14 +690,7 @@ static void mos7840_interrupt_callback(s
 					wreg = MODEM_STATUS_REGISTER;
 					break;
 				}
-				spin_lock(&mos7840_port->pool_lock);
-				if (!mos7840_port->zombie) {
-					rv = mos7840_get_reg(mos7840_port, wval, wreg, &Data);
-				} else {
-					spin_unlock(&mos7840_port->pool_lock);
-					return;
-				}
-				spin_unlock(&mos7840_port->pool_lock);
+				rv = mos7840_get_reg(mos7840_port, wval, wreg, &Data);
 			}
 		}
 	}
@@ -2700,9 +2692,6 @@ static void mos7840_disconnect(struct us
 		mos7840_port = mos7840_get_port_private(serial->port[i]);
 		dbg ("mos7840_port %d = %p", i, mos7840_port);
 		if (mos7840_port) {
-			spin_lock_irqsave(&mos7840_port->pool_lock, flags);
-			mos7840_port->zombie = 1;
-			spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
 			usb_kill_urb(mos7840_port->control_urb);
 		}
 	}

[ 071/101] vhost: fix mergeable bufs on BE hosts

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: "Michael S. Tsirkin" <mst@redhat.com>

commit 910a578f7e9400a78a3b13aba0b4d2df16a2cb05 upstream.

We copy head count to a 16 bit field, this works by chance on LE but on
BE guest gets 0. Fix it up.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/vhost/net.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/drivers/vhost/net.c
+++ b/drivers/vhost/net.c
@@ -379,7 +379,8 @@ static void handle_rx(struct vhost_net *
 		.hdr.gso_type = VIRTIO_NET_HDR_GSO_NONE
 	};
 	size_t total_len = 0;
-	int err, headcount, mergeable;
+	int err, mergeable;
+	s16 headcount;
 	size_t vhost_hlen, sock_hlen;
 	size_t vhost_len, sock_len;
 	/* TODO: check that we are running from vhost_worker? */

[ 072/101] ARM: SAMSUNG: Add naming of s3c64xx-spi devices

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Heiko Stuebner <heiko@sntech.de>

commit 308b3afb97dc342e9c4f958d8b4c459ae0e22bd7 upstream.

Commit a5238e360b71 (spi: s3c64xx: move controller information into driver
data) introduced separate device names for the different subtypes of the
spi controller but forgot to set these in the relevant machines.

To fix this introduce a s3c64xx_spi_setname function and populate all
Samsung arches with the correct names. The function resides in a new
header, as the s3c64xx-spi.h contains driver platform data and should
therefore at some later point move out of the Samsung include dir.

Tested on a s3c2416-based machine.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[s.nawrocki@samsung.com: tested on mach-exynos]
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-exynos/common.c                 |    5 ++++
 arch/arm/mach-s3c24xx/s3c2416.c               |    2 +
 arch/arm/mach-s3c24xx/s3c2443.c               |    4 +++
 arch/arm/mach-s5p64x0/common.c                |    3 ++
 arch/arm/mach-s5pc100/common.c                |    3 ++
 arch/arm/mach-s5pv210/common.c                |    3 ++
 arch/arm/plat-samsung/include/plat/spi-core.h |   30 ++++++++++++++++++++++++++
 7 files changed, 50 insertions(+)

--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -47,6 +47,7 @@
 #include <plat/fimc-core.h>
 #include <plat/iic-core.h>
 #include <plat/tv-core.h>
+#include <plat/spi-core.h>
 #include <plat/regs-serial.h>
 
 #include "common.h"
@@ -346,6 +347,8 @@ static void __init exynos4_map_io(void)
 
 	s5p_fb_setname(0, "exynos4-fb");
 	s5p_hdmi_setname("exynos4-hdmi");
+
+	s3c64xx_spi_setname("exynos4210-spi");
 }
 
 static void __init exynos5_map_io(void)
@@ -366,6 +369,8 @@ static void __init exynos5_map_io(void)
 	s3c_i2c0_setname("s3c2440-i2c");
 	s3c_i2c1_setname("s3c2440-i2c");
 	s3c_i2c2_setname("s3c2440-i2c");
+
+	s3c64xx_spi_setname("exynos4210-spi");
 }
 
 static void __init exynos4_init_clocks(int xtal)
--- a/arch/arm/mach-s3c24xx/s3c2416.c
+++ b/arch/arm/mach-s3c24xx/s3c2416.c
@@ -61,6 +61,7 @@
 #include <plat/nand-core.h>
 #include <plat/adc-core.h>
 #include <plat/rtc-core.h>
+#include <plat/spi-core.h>
 
 static struct map_desc s3c2416_iodesc[] __initdata = {
 	IODESC_ENT(WATCHDOG),
@@ -132,6 +133,7 @@ void __init s3c2416_map_io(void)
 	/* initialize device information early */
 	s3c2416_default_sdhci0();
 	s3c2416_default_sdhci1();
+	s3c64xx_spi_setname("s3c2443-spi");
 
 	iotable_init(s3c2416_iodesc, ARRAY_SIZE(s3c2416_iodesc));
 }
--- a/arch/arm/mach-s3c24xx/s3c2443.c
+++ b/arch/arm/mach-s3c24xx/s3c2443.c
@@ -43,6 +43,7 @@
 #include <plat/nand-core.h>
 #include <plat/adc-core.h>
 #include <plat/rtc-core.h>
+#include <plat/spi-core.h>
 
 static struct map_desc s3c2443_iodesc[] __initdata = {
 	IODESC_ENT(WATCHDOG),
@@ -100,6 +101,9 @@ void __init s3c2443_map_io(void)
 	s3c24xx_gpiocfg_default.set_pull = s3c2443_gpio_setpull;
 	s3c24xx_gpiocfg_default.get_pull = s3c2443_gpio_getpull;
 
+	/* initialize device information early */
+	s3c64xx_spi_setname("s3c2443-spi");
+
 	iotable_init(s3c2443_iodesc, ARRAY_SIZE(s3c2443_iodesc));
 }
 
--- a/arch/arm/mach-s5p64x0/common.c
+++ b/arch/arm/mach-s5p64x0/common.c
@@ -44,6 +44,7 @@
 #include <plat/sdhci.h>
 #include <plat/adc-core.h>
 #include <plat/fb-core.h>
+#include <plat/spi-core.h>
 #include <plat/gpio-cfg.h>
 #include <plat/regs-irqtype.h>
 #include <plat/regs-serial.h>
@@ -179,6 +180,7 @@ void __init s5p6440_map_io(void)
 	/* initialize any device information early */
 	s3c_adc_setname("s3c64xx-adc");
 	s3c_fb_setname("s5p64x0-fb");
+	s3c64xx_spi_setname("s5p64x0-spi");
 
 	s5p64x0_default_sdhci0();
 	s5p64x0_default_sdhci1();
@@ -193,6 +195,7 @@ void __init s5p6450_map_io(void)
 	/* initialize any device information early */
 	s3c_adc_setname("s3c64xx-adc");
 	s3c_fb_setname("s5p64x0-fb");
+	s3c64xx_spi_setname("s5p64x0-spi");
 
 	s5p64x0_default_sdhci0();
 	s5p64x0_default_sdhci1();
--- a/arch/arm/mach-s5pc100/common.c
+++ b/arch/arm/mach-s5pc100/common.c
@@ -45,6 +45,7 @@
 #include <plat/fb-core.h>
 #include <plat/iic-core.h>
 #include <plat/onenand-core.h>
+#include <plat/spi-core.h>
 #include <plat/regs-serial.h>
 #include <plat/watchdog-reset.h>
 
@@ -165,6 +166,8 @@ void __init s5pc100_map_io(void)
 	s3c_onenand_setname("s5pc100-onenand");
 	s3c_fb_setname("s5pc100-fb");
 	s3c_cfcon_setname("s5pc100-pata");
+
+	s3c64xx_spi_setname("s5pc100-spi");
 }
 
 void __init s5pc100_init_clocks(int xtal)
--- a/arch/arm/mach-s5pv210/common.c
+++ b/arch/arm/mach-s5pv210/common.c
@@ -43,6 +43,7 @@
 #include <plat/iic-core.h>
 #include <plat/keypad-core.h>
 #include <plat/tv-core.h>
+#include <plat/spi-core.h>
 #include <plat/regs-serial.h>
 
 #include "common.h"
@@ -196,6 +197,8 @@ void __init s5pv210_map_io(void)
 
 	/* setup TV devices */
 	s5p_hdmi_setname("s5pv210-hdmi");
+
+	s3c64xx_spi_setname("s5pv210-spi");
 }
 
 void __init s5pv210_init_clocks(int xtal)
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/spi-core.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2012 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __PLAT_S3C_SPI_CORE_H
+#define __PLAT_S3C_SPI_CORE_H
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c64xx_spi_setname(char *name)
+{
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+	s3c64xx_device_spi0.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+	s3c64xx_device_spi1.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+	s3c64xx_device_spi2.name = name;
+#endif
+}
+
+#endif /* __PLAT_S3C_SPI_CORE_H */

[ 073/101] ARM: at91/tc: fix typo in the DT document

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Josh Wu <josh.wu@atmel.com>

commit 11930c530f3edf81160e4962e363d579f5cdce7e upstream.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 Documentation/devicetree/bindings/arm/atmel-at91.txt |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -8,7 +8,7 @@ PIT Timer required properties:
   shared across all System Controller members.
 
 TC/TCLIB Timer required properties:
-- compatible: Should be "atmel,<chip>-pit".
+- compatible: Should be "atmel,<chip>-tcb".
   <chip> can be "at91rm9200" or "at91sam9x5"
 - reg: Should contain registers location and length
 - interrupts: Should contain all interrupts for the TC block

[ 074/101] ARM: at91/i2c: change id to let i2c-gpio work

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Bo Shen <voice.shen@atmel.com>

commit 7840487cd6298f9f931103b558290d8d98d41c49 upstream.

The i2c core driver will turn the platform device ID to busnum
When using platfrom device ID as -1, it means dynamically assigned
the busnum. When writing code, we need to make sure the busnum,
and call i2c_register_board_info(int busnum, ...) to register device
if using -1, we do not know the value of busnum

In order to solve this issue, set the platform device ID as a fix number
Here using 0 to match the busnum used in i2c_regsiter_board_info()

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-at91/at91rm9200_devices.c  |    2 +-
 arch/arm/mach-at91/at91sam9260_devices.c |    2 +-
 arch/arm/mach-at91/at91sam9261_devices.c |    2 +-
 arch/arm/mach-at91/at91sam9263_devices.c |    2 +-
 arch/arm/mach-at91/at91sam9rl_devices.c  |    2 +-
 5 files changed, 5 insertions(+), 5 deletions(-)

--- a/arch/arm/mach-at91/at91rm9200_devices.c
+++ b/arch/arm/mach-at91/at91rm9200_devices.c
@@ -463,7 +463,7 @@ static struct i2c_gpio_platform_data pda
 
 static struct platform_device at91rm9200_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -471,7 +471,7 @@ static struct i2c_gpio_platform_data pda
 
 static struct platform_device at91sam9260_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -285,7 +285,7 @@ static struct i2c_gpio_platform_data pda
 
 static struct platform_device at91sam9261_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -542,7 +542,7 @@ static struct i2c_gpio_platform_data pda
 
 static struct platform_device at91sam9263_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -314,7 +314,7 @@ static struct i2c_gpio_platform_data pda
 
 static struct platform_device at91sam9rl_twi_device = {
 	.name			= "i2c-gpio",
-	.id			= -1,
+	.id			= 0,
 	.dev.platform_data	= &pdata,
 };
 

[ 075/101] ARM: at91: at91sam9g10: fix SOC type detection

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ivan Shugov <ivan.shugov@gmail.com>

commit 3d9a0183dd3423353e9e363bcc261c1220d05f9f upstream.

Newer at91sam9g10 SoC revision can't be detected, so the kernel can't boot with
this kind of kernel panic:
"AT91: Impossible to detect the SOC type"

CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Atmel AT91SAM9G10-EK
Ignoring tag cmdline (using the default kernel command line)
bootconsole [earlycon0] enabled
Memory policy: ECC disabled, Data cache writeback
Kernel panic - not syncing: AT91: Impossible to detect the SOC type
[<c00133d4>] (unwind_backtrace+0x0/0xe0) from [<c02366dc>] (panic+0x78/0x1cc)
[<c02366dc>] (panic+0x78/0x1cc) from [<c02fa35c>] (at91_map_io+0x90/0xc8)
[<c02fa35c>] (at91_map_io+0x90/0xc8) from [<c02f9860>] (paging_init+0x564/0x6d0)
[<c02f9860>] (paging_init+0x564/0x6d0) from [<c02f7914>] (setup_arch+0x464/0x704)
[<c02f7914>] (setup_arch+0x464/0x704) from [<c02f44f8>] (start_kernel+0x6c/0x2d4)
[<c02f44f8>] (start_kernel+0x6c/0x2d4) from [<20008040>] (0x20008040)

The reason for this is that the Debug Unit Chip ID Register has changed between
Engineering Sample and definitive revision of the SoC. Changing the check of
cidr to socid will address the problem. We do not integrate this check to the
list just above because we also have to make sure that the extended id is
disregarded.

Signed-off-by: Ivan Shugov <ivan.shugov@gmail.com>
[nicolas.ferre@atmel.com: change commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-at91/setup.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/arm/mach-at91/setup.c
+++ b/arch/arm/mach-at91/setup.c
@@ -151,7 +151,7 @@ static void __init soc_detect(u32 dbgu_b
 	}
 
 	/* at91sam9g10 */
-	if ((cidr & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
+	if ((socid & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
 		at91_soc_initdata.type = AT91_SOC_SAM9G10;
 		at91_boot_soc = at91sam9261_soc;
 	}

[ 076/101] ARM: at91: fix external interrupts in non-DT case

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Nicolas Ferre <nicolas.ferre@atmel.com>

commit 738a0fd752dc60e20beeda6f2f0f62e58dc0e344 upstream.

Management of external interrupts has changed but the
non-DT code has not integrated these changes.
Add a mask to pass external irq specification from SoC
specific code to the at91_aic_init() function.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-at91/generic.h |    3 ++-
 arch/arm/mach-at91/irq.c     |    9 +++++++--
 arch/arm/mach-at91/setup.c   |    2 +-
 3 files changed, 10 insertions(+), 4 deletions(-)

--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -26,7 +26,8 @@ extern void __init at91_dt_initialize(vo
 extern void __init at91_init_irq_default(void);
 extern void __init at91_init_interrupts(unsigned int priority[]);
 extern void __init at91x40_init_interrupts(unsigned int priority[]);
-extern void __init at91_aic_init(unsigned int priority[]);
+extern void __init at91_aic_init(unsigned int priority[],
+				 unsigned int ext_irq_mask);
 extern int  __init at91_aic_of_init(struct device_node *node,
 				    struct device_node *parent);
 extern int  __init at91_aic5_of_init(struct device_node *node,
--- a/arch/arm/mach-at91/irq.c
+++ b/arch/arm/mach-at91/irq.c
@@ -502,14 +502,19 @@ int __init at91_aic5_of_init(struct devi
 /*
  * Initialize the AIC interrupt controller.
  */
-void __init at91_aic_init(unsigned int *priority)
+void __init at91_aic_init(unsigned int *priority, unsigned int ext_irq_mask)
 {
 	unsigned int i;
 	int irq_base;
 
-	if (at91_aic_pm_init())
+	at91_extern_irq = kzalloc(BITS_TO_LONGS(n_irqs)
+				  * sizeof(*at91_extern_irq), GFP_KERNEL);
+
+	if (at91_aic_pm_init() || at91_extern_irq == NULL)
 		panic("Unable to allocate bit maps\n");
 
+	*at91_extern_irq = ext_irq_mask;
+
 	at91_aic_base = ioremap(AT91_AIC, 512);
 	if (!at91_aic_base)
 		panic("Unable to ioremap AIC registers\n");
--- a/arch/arm/mach-at91/setup.c
+++ b/arch/arm/mach-at91/setup.c
@@ -47,7 +47,7 @@ void __init at91_init_irq_default(void)
 void __init at91_init_interrupts(unsigned int *priority)
 {
 	/* Initialize the AIC interrupt controller */
-	at91_aic_init(priority);
+	at91_aic_init(priority, at91_extern_irq);
 
 	/* Enable GPIO interrupts */
 	at91_gpio_irq_setup();

[ 077/101] ARM: at91: fix external interrupt specification in board code

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Nicolas Ferre <nicolas.ferre@atmel.com>

commit 69e7ea04c9365626c0963ff09bbaa3a1b49e293a upstream.

Since the switch to sparse irq, we have to add the NR_IRQS_LEGACY
offset to static irq numbers. It has been forgotten on these
SPI irq definitions in board code.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-at91/board-neocore926.c |    2 +-
 arch/arm/mach-at91/board-sam9261ek.c  |    2 +-
 arch/arm/mach-at91/board-sam9263ek.c  |    2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

--- a/arch/arm/mach-at91/board-neocore926.c
+++ b/arch/arm/mach-at91/board-neocore926.c
@@ -129,7 +129,7 @@ static struct spi_board_info neocore926_
 		.max_speed_hz	= 125000 * 16,
 		.bus_num	= 0,
 		.platform_data	= &ads_info,
-		.irq		= AT91SAM9263_ID_IRQ1,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
 	},
 #endif
 };
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -309,7 +309,7 @@ static struct spi_board_info ek_spi_devi
 		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
 		.bus_num	= 0,
 		.platform_data	= &ads_info,
-		.irq		= AT91SAM9261_ID_IRQ0,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9261_ID_IRQ0,
 		.controller_data = (void *) AT91_PIN_PA28,	/* CS pin */
 	},
 #endif
--- a/arch/arm/mach-at91/board-sam9263ek.c
+++ b/arch/arm/mach-at91/board-sam9263ek.c
@@ -132,7 +132,7 @@ static struct spi_board_info ek_spi_devi
 		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
 		.bus_num	= 0,
 		.platform_data	= &ads_info,
-		.irq		= AT91SAM9263_ID_IRQ1,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
 	},
 #endif
 };

[ 078/101] mac80211: connect with HT20 if HT40 is not permitted

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johannes Berg <johannes.berg@intel.com>

commit 3a40414f826a8f1096d9b94c4a53ef91b25ba28d upstream.

Some changes to fix issues with HT40 APs in Korea
and follow-up changes to allow using HT40 even if
the local regulatory database disallows it caused
issues with iwlwifi (and could cause issues with
other devices); iwlwifi firmware would assert if
you tried to connect to an AP that has an invalid
configuration (e.g. using HT40- on channel 140.)

Fix this, while avoiding the "Korean AP" issue by
disabling HT40 and advertising HT20 to the AP
when connecting.

Reported-by: Florian Reitmeir <florian@reitmeir.org>
Tested-by: Florian Reitmeir <florian@reitmeir.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/mac80211/mlme.c |   30 ++++++++++++++++++++----------
 1 file changed, 20 insertions(+), 10 deletions(-)

--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -3065,22 +3065,32 @@ static int ieee80211_prep_connection(str
 				   ht_cfreq, ht_oper->primary_chan,
 				   cbss->channel->band);
 			ht_oper = NULL;
+		} else {
+			channel_type = NL80211_CHAN_HT20;
 		}
 	}
 
-	if (ht_oper) {
-		channel_type = NL80211_CHAN_HT20;
+	if (ht_oper && sband->ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40) {
+		/*
+		 * cfg80211 already verified that the channel itself can
+		 * be used, but it didn't check that we can do the right
+		 * HT type, so do that here as well. If HT40 isn't allowed
+		 * on this channel, disable 40 MHz operation.
+		 */
 
-		if (sband->ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40) {
-			switch (ht_oper->ht_param &
-					IEEE80211_HT_PARAM_CHA_SEC_OFFSET) {
-			case IEEE80211_HT_PARAM_CHA_SEC_ABOVE:
+		switch (ht_oper->ht_param & IEEE80211_HT_PARAM_CHA_SEC_OFFSET) {
+		case IEEE80211_HT_PARAM_CHA_SEC_ABOVE:
+			if (cbss->channel->flags & IEEE80211_CHAN_NO_HT40PLUS)
+				ifmgd->flags |= IEEE80211_STA_DISABLE_40MHZ;
+			else
 				channel_type = NL80211_CHAN_HT40PLUS;
-				break;
-			case IEEE80211_HT_PARAM_CHA_SEC_BELOW:
+			break;
+		case IEEE80211_HT_PARAM_CHA_SEC_BELOW:
+			if (cbss->channel->flags & IEEE80211_CHAN_NO_HT40MINUS)
+				ifmgd->flags |= IEEE80211_STA_DISABLE_40MHZ;
+			else
 				channel_type = NL80211_CHAN_HT40MINUS;
-				break;
-			}
+			break;
 		}
 	}
 

[ 079/101] mac80211: check if key has TKIP type before updating IV

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Stanislaw Gruszka <sgruszka@redhat.com>

commit 4045f72bcf3c293c7c5932ef001742d8bb5ded76 upstream.

This patch fix corruption which can manifest itself by following crash
when switching on rfkill switch with rt2x00 driver:
https://bugzilla.redhat.com/attachment.cgi?id=615362

Pointer key->u.ccmp.tfm of group key get corrupted in:

ieee80211_rx_h_michael_mic_verify():

        /* update IV in key information to be able to detect replays */
        rx->key->u.tkip.rx[rx->security_idx].iv32 = rx->tkip_iv32;
        rx->key->u.tkip.rx[rx->security_idx].iv16 = rx->tkip_iv16;

because rt2x00 always set RX_FLAG_MMIC_STRIPPED, even if key is not TKIP.

We already check type of the key in different path in
ieee80211_rx_h_michael_mic_verify() function, so adding additional
check here is reasonable.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/mac80211/wpa.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/net/mac80211/wpa.c
+++ b/net/mac80211/wpa.c
@@ -106,7 +106,8 @@ ieee80211_rx_h_michael_mic_verify(struct
 		if (status->flag & RX_FLAG_MMIC_ERROR)
 			goto mic_fail;
 
-		if (!(status->flag & RX_FLAG_IV_STRIPPED) && rx->key)
+		if (!(status->flag & RX_FLAG_IV_STRIPPED) && rx->key &&
+		    rx->key->conf.cipher == WLAN_CIPHER_SUITE_TKIP)
 			goto update_iv;
 
 		return RX_CONTINUE;

[ 080/101] mac80211: use ieee80211_free_txskb in a few more places

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Felix Fietkau <nbd@openwrt.org>

commit d4fa14cd62bd078c8e3ef39283b9f237e5b2ff0f upstream.

Free tx status skbs when draining power save buffers, pending frames, or
when tearing down a vif.
Fixes remaining conditions that can lead to hostapd/wpa_supplicant hangs when
running out of socket write memory.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/mac80211/iface.c    |    2 +-
 net/mac80211/sta_info.c |    4 ++--
 net/mac80211/util.c     |    4 ++--
 3 files changed, 5 insertions(+), 5 deletions(-)

--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -822,7 +822,7 @@ static void ieee80211_do_stop(struct iee
 			struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 			if (info->control.vif == &sdata->vif) {
 				__skb_unlink(skb, &local->pending[i]);
-				dev_kfree_skb_irq(skb);
+				ieee80211_free_txskb(&local->hw, skb);
 			}
 		}
 	}
--- a/net/mac80211/sta_info.c
+++ b/net/mac80211/sta_info.c
@@ -585,7 +585,7 @@ static bool sta_info_cleanup_expire_buff
 		 */
 		if (!skb)
 			break;
-		dev_kfree_skb(skb);
+		ieee80211_free_txskb(&local->hw, skb);
 	}
 
 	/*
@@ -614,7 +614,7 @@ static bool sta_info_cleanup_expire_buff
 		local->total_ps_buffered--;
 		ps_dbg(sta->sdata, "Buffered frame expired (STA %pM)\n",
 		       sta->sta.addr);
-		dev_kfree_skb(skb);
+		ieee80211_free_txskb(&local->hw, skb);
 	}
 
 	/*
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@ -400,7 +400,7 @@ void ieee80211_add_pending_skb(struct ie
 	int queue = info->hw_queue;
 
 	if (WARN_ON(!info->control.vif)) {
-		kfree_skb(skb);
+		ieee80211_free_txskb(&local->hw, skb);
 		return;
 	}
 
@@ -425,7 +425,7 @@ void ieee80211_add_pending_skbs_fn(struc
 		struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 
 		if (WARN_ON(!info->control.vif)) {
-			kfree_skb(skb);
+			ieee80211_free_txskb(&local->hw, skb);
 			continue;
 		}
 

[ 081/101] b43: Fix oops on unload when firmware not found

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Larry Finger <Larry.Finger@lwfinger.net>

commit f89ff6441df06abc2d95f3ef67525923032d6283 upstream.

When b43 fails to find firmware when loaded, a subsequent unload will
oops due to calling ieee80211_unregister_hw() when the corresponding
register call was never made.

Commit 2d838bb608e2d1f6cb4280e76748cb812dc822e7 fixed the same problem
for b43legacy.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Markus Kanet <dvmailing@gmx.eu>
Cc: Markus Kanet <dvmailing@gmx.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/b43/main.c |    4 ++++
 1 file changed, 4 insertions(+)

--- a/drivers/net/wireless/b43/main.c
+++ b/drivers/net/wireless/b43/main.c
@@ -5374,6 +5374,8 @@ static void b43_bcma_remove(struct bcma_
 	cancel_work_sync(&wldev->restart_work);
 
 	B43_WARN_ON(!wl);
+	if (!wldev->fw.ucode.data)
+		return;			/* NULL if firmware never loaded */
 	if (wl->current_dev == wldev && wl->hw_registred) {
 		b43_leds_stop(wldev);
 		ieee80211_unregister_hw(wl->hw);
@@ -5448,6 +5450,8 @@ static void b43_ssb_remove(struct ssb_de
 	cancel_work_sync(&wldev->restart_work);
 
 	B43_WARN_ON(!wl);
+	if (!wldev->fw.ucode.data)
+		return;			/* NULL if firmware never loaded */
 	if (wl->current_dev == wldev && wl->hw_registred) {
 		b43_leds_stop(wldev);
 		ieee80211_unregister_hw(wl->hw);

[ 082/101] tilegx: fix some issues in the SW TSO support

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Chris Metcalf <cmetcalf@tilera.com>

commit 3da3fff8006c608f19a51859d44ba47ca8b41461 upstream.

This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance.  Also adopt use of skb_frag_size() accessor.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/ethernet/tile/tilegx.c |   35 +++++++++++++++++++----------------
 1 file changed, 19 insertions(+), 16 deletions(-)

--- a/drivers/net/ethernet/tile/tilegx.c
+++ b/drivers/net/ethernet/tile/tilegx.c
@@ -1334,11 +1334,11 @@ static int tso_count_edescs(struct sk_bu
 {
 	struct skb_shared_info *sh = skb_shinfo(skb);
 	unsigned int sh_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
-	unsigned int data_len = skb->data_len + skb->hdr_len - sh_len;
+	unsigned int data_len = skb->len - sh_len;
 	unsigned int p_len = sh->gso_size;
 	long f_id = -1;    /* id of the current fragment */
-	long f_size = skb->hdr_len;  /* size of the current fragment */
-	long f_used = sh_len;  /* bytes used from the current fragment */
+	long f_size = skb_headlen(skb) - sh_len;  /* current fragment size */
+	long f_used = 0;  /* bytes used from the current fragment */
 	long n;            /* size of the current piece of payload */
 	int num_edescs = 0;
 	int segment;
@@ -1353,7 +1353,7 @@ static int tso_count_edescs(struct sk_bu
 			/* Advance as needed. */
 			while (f_used >= f_size) {
 				f_id++;
-				f_size = sh->frags[f_id].size;
+				f_size = skb_frag_size(&sh->frags[f_id]);
 				f_used = 0;
 			}
 
@@ -1384,13 +1384,13 @@ static void tso_headers_prepare(struct s
 	struct iphdr *ih;
 	struct tcphdr *th;
 	unsigned int sh_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
-	unsigned int data_len = skb->data_len + skb->hdr_len - sh_len;
+	unsigned int data_len = skb->len - sh_len;
 	unsigned char *data = skb->data;
 	unsigned int ih_off, th_off, p_len;
 	unsigned int isum_seed, tsum_seed, id, seq;
 	long f_id = -1;    /* id of the current fragment */
-	long f_size = skb->hdr_len;  /* size of the current fragment */
-	long f_used = sh_len;  /* bytes used from the current fragment */
+	long f_size = skb_headlen(skb) - sh_len;  /* current fragment size */
+	long f_used = 0;  /* bytes used from the current fragment */
 	long n;            /* size of the current piece of payload */
 	int segment;
 
@@ -1405,7 +1405,7 @@ static void tso_headers_prepare(struct s
 	isum_seed = ((0xFFFF - ih->check) +
 		     (0xFFFF - ih->tot_len) +
 		     (0xFFFF - ih->id));
-	tsum_seed = th->check + (0xFFFF ^ htons(sh_len + data_len));
+	tsum_seed = th->check + (0xFFFF ^ htons(skb->len));
 	id = ntohs(ih->id);
 	seq = ntohl(th->seq);
 
@@ -1444,7 +1444,7 @@ static void tso_headers_prepare(struct s
 			/* Advance as needed. */
 			while (f_used >= f_size) {
 				f_id++;
-				f_size = sh->frags[f_id].size;
+				f_size = skb_frag_size(&sh->frags[f_id]);
 				f_used = 0;
 			}
 
@@ -1478,14 +1478,14 @@ static void tso_egress(struct net_device
 	struct tile_net_priv *priv = netdev_priv(dev);
 	struct skb_shared_info *sh = skb_shinfo(skb);
 	unsigned int sh_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
-	unsigned int data_len = skb->data_len + skb->hdr_len - sh_len;
+	unsigned int data_len = skb->len - sh_len;
 	unsigned int p_len = sh->gso_size;
 	gxio_mpipe_edesc_t edesc_head = { { 0 } };
 	gxio_mpipe_edesc_t edesc_body = { { 0 } };
 	long f_id = -1;    /* id of the current fragment */
-	long f_size = skb->hdr_len;  /* size of the current fragment */
-	long f_used = sh_len;  /* bytes used from the current fragment */
-	void *f_data = skb->data;
+	long f_size = skb_headlen(skb) - sh_len;  /* current fragment size */
+	long f_used = 0;  /* bytes used from the current fragment */
+	void *f_data = skb->data + sh_len;
 	long n;            /* size of the current piece of payload */
 	unsigned long tx_packets = 0, tx_bytes = 0;
 	unsigned int csum_start;
@@ -1516,15 +1516,18 @@ static void tso_egress(struct net_device
 
 		/* Egress the payload. */
 		while (p_used < p_len) {
+			void *va;
 
 			/* Advance as needed. */
 			while (f_used >= f_size) {
 				f_id++;
-				f_size = sh->frags[f_id].size;
-				f_used = 0;
+				f_size = skb_frag_size(&sh->frags[f_id]);
 				f_data = tile_net_frag_buf(&sh->frags[f_id]);
+				f_used = 0;
 			}
 
+			va = f_data + f_used;
+
 			/* Use bytes from the current fragment. */
 			n = p_len - p_used;
 			if (n > f_size - f_used)
@@ -1533,7 +1536,7 @@ static void tso_egress(struct net_device
 			p_used += n;
 
 			/* Egress a piece of the payload. */
-			edesc_body.va = va_to_tile_io_addr(f_data) + f_used;
+			edesc_body.va = va_to_tile_io_addr(va);
 			edesc_body.xfer_size = n;
 			edesc_body.bound = !(p_used < p_len);
 			gxio_mpipe_equeue_put_at(equeue, edesc_body, slot);

[ 083/101] Bluetooth: SMP: Fix setting unknown auth_req bits

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johan Hedberg <johan.hedberg@intel.com>

commit 065a13e2cc665f6547dc7e8a9d6b6565badf940a upstream.

When sending a pairing request or response we should not just blindly
copy the value that the remote device sent. Instead we should at least
make sure to mask out any unknown bits. This is particularly critical
from the upcoming LE Secure Connections feature perspective as
incorrectly indicating support for it (by copying the remote value)
would cause a failure to pair with devices that support it.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/bluetooth/smp.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

--- a/net/bluetooth/smp.c
+++ b/net/bluetooth/smp.c
@@ -32,6 +32,8 @@
 
 #define SMP_TIMEOUT	msecs_to_jiffies(30000)
 
+#define AUTH_REQ_MASK   0x07
+
 static inline void swap128(u8 src[16], u8 dst[16])
 {
 	int i;
@@ -230,7 +232,7 @@ static void build_pairing_cmd(struct l2c
 		req->max_key_size = SMP_MAX_ENC_KEY_SIZE;
 		req->init_key_dist = 0;
 		req->resp_key_dist = dist_keys;
-		req->auth_req = authreq;
+		req->auth_req = (authreq & AUTH_REQ_MASK);
 		return;
 	}
 
@@ -239,7 +241,7 @@ static void build_pairing_cmd(struct l2c
 	rsp->max_key_size = SMP_MAX_ENC_KEY_SIZE;
 	rsp->init_key_dist = 0;
 	rsp->resp_key_dist = req->resp_key_dist & dist_keys;
-	rsp->auth_req = authreq;
+	rsp->auth_req = (authreq & AUTH_REQ_MASK);
 }
 
 static u8 check_enc_key_size(struct l2cap_conn *conn, __u8 max_key_size)

[ 084/101] qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Dan Williams <dcbw@redhat.com>

commit f8295ec22cb0f1ee6849b862addbfa3ea9320755 upstream.

These devices provide QMI and ethernet functionality via a standard CDC
ethernet descriptor.  But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface.  Thus blacklist the devices in cdc_ether and add their IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/usb/cdc_ether.c |   41 ++++++++++++++++++++++++++---------------
 drivers/net/usb/qmi_wwan.c  |   14 ++++++++++++++
 2 files changed, 40 insertions(+), 15 deletions(-)

--- a/drivers/net/usb/cdc_ether.c
+++ b/drivers/net/usb/cdc_ether.c
@@ -592,6 +592,32 @@ static const struct usb_device_id	produc
 	.driver_info		= 0,
 },
 
+/* Novatel USB551L and MC551 - handled by qmi_wwan */
+{
+	.match_flags    =   USB_DEVICE_ID_MATCH_VENDOR
+		 | USB_DEVICE_ID_MATCH_PRODUCT
+		 | USB_DEVICE_ID_MATCH_INT_INFO,
+	.idVendor               = NOVATEL_VENDOR_ID,
+	.idProduct		= 0xB001,
+	.bInterfaceClass	= USB_CLASS_COMM,
+	.bInterfaceSubClass	= USB_CDC_SUBCLASS_ETHERNET,
+	.bInterfaceProtocol	= USB_CDC_PROTO_NONE,
+	.driver_info = 0,
+},
+
+/* Novatel E362 - handled by qmi_wwan */
+{
+	.match_flags    =   USB_DEVICE_ID_MATCH_VENDOR
+		 | USB_DEVICE_ID_MATCH_PRODUCT
+		 | USB_DEVICE_ID_MATCH_INT_INFO,
+	.idVendor               = NOVATEL_VENDOR_ID,
+	.idProduct		= 0x9010,
+	.bInterfaceClass	= USB_CLASS_COMM,
+	.bInterfaceSubClass	= USB_CDC_SUBCLASS_ETHERNET,
+	.bInterfaceProtocol	= USB_CDC_PROTO_NONE,
+	.driver_info = 0,
+},
+
 /*
  * WHITELIST!!!
  *
@@ -604,21 +630,6 @@ static const struct usb_device_id	produc
  * because of bugs/quirks in a given product (like Zaurus, above).
  */
 {
-	/* Novatel USB551L */
-	/* This match must come *before* the generic CDC-ETHER match so that
-	 * we get FLAG_WWAN set on the device, since it's descriptors are
-	 * generic CDC-ETHER.
-	 */
-	.match_flags    =   USB_DEVICE_ID_MATCH_VENDOR
-		 | USB_DEVICE_ID_MATCH_PRODUCT
-		 | USB_DEVICE_ID_MATCH_INT_INFO,
-	.idVendor               = NOVATEL_VENDOR_ID,
-	.idProduct		= 0xB001,
-	.bInterfaceClass	= USB_CLASS_COMM,
-	.bInterfaceSubClass	= USB_CDC_SUBCLASS_ETHERNET,
-	.bInterfaceProtocol	= USB_CDC_PROTO_NONE,
-	.driver_info = (unsigned long)&wwan_info,
-}, {
 	/* ZTE (Vodafone) K3805-Z */
 	.match_flags    =   USB_DEVICE_ID_MATCH_VENDOR
 		 | USB_DEVICE_ID_MATCH_PRODUCT
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -364,6 +364,20 @@ static const struct usb_device_id produc
 		USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 57),
 		.driver_info        = (unsigned long)&qmi_wwan_info,
 	},
+	{	/* Novatel USB551L and MC551 */
+		USB_DEVICE_AND_INTERFACE_INFO(0x1410, 0xb001,
+		                              USB_CLASS_COMM,
+		                              USB_CDC_SUBCLASS_ETHERNET,
+		                              USB_CDC_PROTO_NONE),
+		.driver_info        = (unsigned long)&qmi_wwan_info,
+	},
+	{	/* Novatel E362 */
+		USB_DEVICE_AND_INTERFACE_INFO(0x1410, 0x9010,
+		                              USB_CLASS_COMM,
+		                              USB_CDC_SUBCLASS_ETHERNET,
+		                              USB_CDC_PROTO_NONE),
+		.driver_info        = (unsigned long)&qmi_wwan_info,
+	},
 
 	/* 2. Combined interface devices matching on class+protocol */
 	{	/* Huawei E367 and possibly others in "Windows mode" */

[ 085/101] freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Oleg Nesterov <oleg@redhat.com>

commit b40a79591ca918e7b91b0d9b6abd5d00f2e88c19 upstream.

flush_old_exec() clears PF_KTHREAD but forgets about PF_NOFREEZE.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/exec.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/fs/exec.c
+++ b/fs/exec.c
@@ -1110,7 +1110,8 @@ int flush_old_exec(struct linux_binprm *
 	bprm->mm = NULL;		/* We're using it now */
 
 	set_fs(USER_DS);
-	current->flags &= ~(PF_RANDOMIZE | PF_FORKNOEXEC | PF_KTHREAD);
+	current->flags &=
+		~(PF_RANDOMIZE | PF_FORKNOEXEC | PF_KTHREAD | PF_NOFREEZE);
 	flush_thread();
 	current->personality &= ~bprm->per_clear;
 

[ 086/101] dmaengine: sirf: fix a typo in dma_prep_interleaved

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Barry Song <Baohua.Song@csr.com>

commit 5997e089e4c3a7f0958a8fb0a54ec2b5a6f06168 upstream.

either DEV_TO_MEM or MEM_TO_DEV is supported, so change
OR to AND.

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/dma/sirf-dma.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/dma/sirf-dma.c
+++ b/drivers/dma/sirf-dma.c
@@ -428,7 +428,7 @@ static struct dma_async_tx_descriptor *s
 	unsigned long iflags;
 	int ret;
 
-	if ((xt->dir != DMA_MEM_TO_DEV) || (xt->dir != DMA_DEV_TO_MEM)) {
+	if ((xt->dir != DMA_MEM_TO_DEV) && (xt->dir != DMA_DEV_TO_MEM)) {
 		ret = -EINVAL;
 		goto err_dir;
 	}

[ 087/101] dmaengine: sirf: fix a typo in moving running dma_desc to active queue

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Barry Song <Baohua.Song@csr.com>

commit 26fd12209c08fe947be1828896ef4ffc5bd0e6df upstream.

list_move_tail(&schan->queued, &schan->active) makes the list_empty(schan->queued)
undefined, we either should change it to:
list_move_tail(schan->queued.next, &schan->active)
or
list_move_tail(&sdesc->node, &schan->active)

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/dma/sirf-dma.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/dma/sirf-dma.c
+++ b/drivers/dma/sirf-dma.c
@@ -109,7 +109,7 @@ static void sirfsoc_dma_execute(struct s
 	sdesc = list_first_entry(&schan->queued, struct sirfsoc_dma_desc,
 		node);
 	/* Move the first queued descriptor to active list */
-	list_move_tail(&schan->queued, &schan->active);
+	list_move_tail(&sdesc->node, &schan->active);
 
 	/* Start the DMA transfer */
 	writel_relaxed(sdesc->width, sdma->base + SIRFSOC_DMA_WIDTH_0 +

[ 088/101] dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Wei Yongjun <yongjun_wei@trendmicro.com.cn>

commit 720dfd250e48a8c7fd1b2b8645955413989c4ee0 upstream.

Add the missing unlock on the error handling path in function
imxdma_xfer_desc().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/dma/imx-dma.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/drivers/dma/imx-dma.c
+++ b/drivers/dma/imx-dma.c
@@ -474,8 +474,10 @@ static int imxdma_xfer_desc(struct imxdm
 			slot = i;
 			break;
 		}
-		if (slot < 0)
+		if (slot < 0) {
+			spin_unlock_irqrestore(&imxdma->lock, flags);
 			return -EBUSY;
+		}
 
 		imxdma->slots_2d[slot].xsr = d->x;
 		imxdma->slots_2d[slot].ysr = d->y;

[ 089/101] iwlwifi: fix 6000 series channel switch command

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Johannes Berg <johannes.berg@intel.com>

commit 8f7b8db6e0557c8437adf9371e020cd89a7e85dc upstream.

The channel switch command for 6000 series devices
is larger than the maximum inline command size of
320 bytes. The command is therefore refused with a
warning. Fix this by allocating the command and
using the NOCOPY mechanism.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/iwlwifi/dvm/devices.c |   39 +++++++++++++++++------------
 1 file changed, 24 insertions(+), 15 deletions(-)

--- a/drivers/net/wireless/iwlwifi/dvm/devices.c
+++ b/drivers/net/wireless/iwlwifi/dvm/devices.c
@@ -518,7 +518,7 @@ static int iwl6000_hw_channel_switch(str
 	 * See iwlagn_mac_channel_switch.
 	 */
 	struct iwl_rxon_context *ctx = &priv->contexts[IWL_RXON_CTX_BSS];
-	struct iwl6000_channel_switch_cmd cmd;
+	struct iwl6000_channel_switch_cmd *cmd;
 	u32 switch_time_in_usec, ucode_switch_time;
 	u16 ch;
 	u32 tsf_low;
@@ -527,18 +527,25 @@ static int iwl6000_hw_channel_switch(str
 	struct ieee80211_vif *vif = ctx->vif;
 	struct iwl_host_cmd hcmd = {
 		.id = REPLY_CHANNEL_SWITCH,
-		.len = { sizeof(cmd), },
+		.len = { sizeof(*cmd), },
 		.flags = CMD_SYNC,
-		.data = { &cmd, },
+		.dataflags[0] = IWL_HCMD_DFL_NOCOPY,
 	};
+	int err;
 
-	cmd.band = priv->band == IEEE80211_BAND_2GHZ;
+	cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return -ENOMEM;
+
+	hcmd.data[0] = cmd;
+
+	cmd->band = priv->band == IEEE80211_BAND_2GHZ;
 	ch = ch_switch->channel->hw_value;
 	IWL_DEBUG_11H(priv, "channel switch from %u to %u\n",
 		      ctx->active.channel, ch);
-	cmd.channel = cpu_to_le16(ch);
-	cmd.rxon_flags = ctx->staging.flags;
-	cmd.rxon_filter_flags = ctx->staging.filter_flags;
+	cmd->channel = cpu_to_le16(ch);
+	cmd->rxon_flags = ctx->staging.flags;
+	cmd->rxon_filter_flags = ctx->staging.filter_flags;
 	switch_count = ch_switch->count;
 	tsf_low = ch_switch->timestamp & 0x0ffffffff;
 	/*
@@ -554,23 +561,25 @@ static int iwl6000_hw_channel_switch(str
 			switch_count = 0;
 	}
 	if (switch_count <= 1)
-		cmd.switch_time = cpu_to_le32(priv->ucode_beacon_time);
+		cmd->switch_time = cpu_to_le32(priv->ucode_beacon_time);
 	else {
 		switch_time_in_usec =
 			vif->bss_conf.beacon_int * switch_count * TIME_UNIT;
 		ucode_switch_time = iwl_usecs_to_beacons(priv,
 							 switch_time_in_usec,
 							 beacon_interval);
-		cmd.switch_time = iwl_add_beacon_time(priv,
-						      priv->ucode_beacon_time,
-						      ucode_switch_time,
-						      beacon_interval);
+		cmd->switch_time = iwl_add_beacon_time(priv,
+						       priv->ucode_beacon_time,
+						       ucode_switch_time,
+						       beacon_interval);
 	}
 	IWL_DEBUG_11H(priv, "uCode time for the switch is 0x%x\n",
-		      cmd.switch_time);
-	cmd.expect_beacon = ch_switch->channel->flags & IEEE80211_CHAN_RADAR;
+		      cmd->switch_time);
+	cmd->expect_beacon = ch_switch->channel->flags & IEEE80211_CHAN_RADAR;
 
-	return iwl_dvm_send_cmd(priv, &hcmd);
+	err = iwl_dvm_send_cmd(priv, &hcmd);
+	kfree(cmd);
+	return err;
 }
 
 struct iwl_lib_ops iwl6000_lib = {

[ 090/101] bcma: fix unregistration of cores

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Piotr Haber <phaber@broadcom.com>

commit 1fffa905adffbf0d3767fc978ef09afb830275eb upstream.

When cores are unregistered, entries
need to be removed from cores list in a safe manner.

Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/bcma/main.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/drivers/bcma/main.c
+++ b/drivers/bcma/main.c
@@ -141,9 +141,10 @@ static int bcma_register_cores(struct bc
 
 static void bcma_unregister_cores(struct bcma_bus *bus)
 {
-	struct bcma_device *core;
+	struct bcma_device *core, *tmp;
 
-	list_for_each_entry(core, &bus->cores, list) {
+	list_for_each_entry_safe(core, tmp, &bus->cores, list) {
+		list_del(&core->list);
 		if (core->dev_registered)
 			device_unregister(&core->dev);
 	}

[ 091/101] net/wireless: ipw2200: Fix panic occurring in ipw_handle_promiscuous_tx()

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Stanislav Yakovlev <stas.yakovlev@gmail.com>

commit bf11315eeda510ea4fc1a2bf972d8155d31d89b4 upstream.

The driver does not count space of radiotap fields when allocating skb for
radiotap packet. This leads to kernel panic with the following call trace:

...
[67607.676067] [<c152f90f>] error_code+0x67/0x6c
[67607.676067] [<c142f831>] ? skb_put+0x91/0xa0
[67607.676067] [<f8cf5e5b>] ? ipw_handle_promiscuous_tx+0x16b/0x2d0 [ipw2200]
[67607.676067] [<f8cf5e5b>] ipw_handle_promiscuous_tx+0x16b/0x2d0 [ipw2200]
[67607.676067] [<f8cf899b>] ipw_net_hard_start_xmit+0x8b/0x90 [ipw2200]
[67607.676067] [<f8741c5a>] libipw_xmit+0x55a/0x980 [libipw]
[67607.676067] [<c143d3e8>] dev_hard_start_xmit+0x218/0x4d0
...

This bug was found by VittGam.
https://bugzilla.kernel.org/show_bug.cgi?id=43255

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/ipw2x00/ipw2200.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/net/wireless/ipw2x00/ipw2200.c
+++ b/drivers/net/wireless/ipw2x00/ipw2200.c
@@ -10479,7 +10479,7 @@ static void ipw_handle_promiscuous_tx(st
 		} else
 			len = src->len;
 
-		dst = alloc_skb(len + sizeof(*rt_hdr), GFP_ATOMIC);
+		dst = alloc_skb(len + sizeof(*rt_hdr) + sizeof(u16)*2, GFP_ATOMIC);
 		if (!dst)
 			continue;
 

[ 092/101] cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Andreas Herrmann <andreas.herrmann3@amd.com>

commit e4df1cbcc1f329e53a1fff7450b2229e0addff20 upstream.

Commit 6889125b8b4e09c5e53e6ecab3433bed1ce198c9
(cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU)
causes powernow-k8 to trigger a preempt warning, e.g.:

  BUG: using smp_processor_id() in preemptible [00000000] code: cpufreq/3776
  caller is powernowk8_target+0x20/0x49
  Pid: 3776, comm: cpufreq Not tainted 3.6.0 #9
  Call Trace:
   [<ffffffff8125b447>] debug_smp_processor_id+0xc7/0xe0
   [<ffffffff814877e7>] powernowk8_target+0x20/0x49
   [<ffffffff81482b02>] __cpufreq_driver_target+0x82/0x8a
   [<ffffffff81484fc6>] cpufreq_governor_performance+0x4e/0x54
   [<ffffffff81482c50>] __cpufreq_governor+0x8c/0xc9
   [<ffffffff81482e6f>] __cpufreq_set_policy+0x1a9/0x21e
   [<ffffffff814839af>] store_scaling_governor+0x16f/0x19b
   [<ffffffff81484f16>] ? cpufreq_update_policy+0x124/0x124
   [<ffffffff8162b4a5>] ? _raw_spin_unlock_irqrestore+0x2c/0x49
   [<ffffffff81483640>] store+0x60/0x88
   [<ffffffff811708c0>] sysfs_write_file+0xf4/0x130
   [<ffffffff8111243b>] vfs_write+0xb5/0x151
   [<ffffffff811126e0>] sys_write+0x4a/0x71
   [<ffffffff816319a9>] system_call_fastpath+0x16/0x1b

Fix this by by always using work_on_cpu().

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/cpufreq/powernow-k8.c |    9 +--------
 1 file changed, 1 insertion(+), 8 deletions(-)

--- a/drivers/cpufreq/powernow-k8.c
+++ b/drivers/cpufreq/powernow-k8.c
@@ -1223,14 +1223,7 @@ static int powernowk8_target(struct cpuf
 	struct powernowk8_target_arg pta = { .pol = pol, .targfreq = targfreq,
 					     .relation = relation };
 
-	/*
-	 * Must run on @pol->cpu.  cpufreq core is responsible for ensuring
-	 * that we're bound to the current CPU and pol->cpu stays online.
-	 */
-	if (smp_processor_id() == pol->cpu)
-		return powernowk8_target_fn(&pta);
-	else
-		return work_on_cpu(pol->cpu, powernowk8_target_fn, &pta);
+	return work_on_cpu(pol->cpu, powernowk8_target_fn, &pta);
 }
 
 /* Driver entry point to verify the policy and range of frequencies */

[ 093/101] Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Felix Fietkau <nbd@openwrt.org>

commit 73b26df5fa1a6245d6fc982362518b620bc7c2fe upstream.

This reverts commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd.

This commit is reducing tx power by at least 10 db on some devices,
e.g. the Buffalo WZR-HP-G450H.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h |  164 +++++++++----------
 1 file changed, 82 insertions(+), 82 deletions(-)

--- a/drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h
@@ -534,107 +534,107 @@ static const u32 ar9300_2p2_baseband_cor
 
 static const u32 ar9300Modes_high_power_tx_gain_table_2p2[][5] = {
 	/* Addr      5G_HT20     5G_HT40     2G_HT40     2G_HT20   */
-	{0x0000a2dc, 0x000cfff0, 0x000cfff0, 0x03aaa352, 0x03aaa352},
-	{0x0000a2e0, 0x000f0000, 0x000f0000, 0x03ccc584, 0x03ccc584},
-	{0x0000a2e4, 0x03f00000, 0x03f00000, 0x03f0f800, 0x03f0f800},
+	{0x0000a2dc, 0x00033800, 0x00033800, 0x03aaa352, 0x03aaa352},
+	{0x0000a2e0, 0x0003c000, 0x0003c000, 0x03ccc584, 0x03ccc584},
+	{0x0000a2e4, 0x03fc0000, 0x03fc0000, 0x03f0f800, 0x03f0f800},
 	{0x0000a2e8, 0x00000000, 0x00000000, 0x03ff0000, 0x03ff0000},
 	{0x0000a410, 0x000050d9, 0x000050d9, 0x000050d9, 0x000050d9},
 	{0x0000a500, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
 	{0x0000a504, 0x06000003, 0x06000003, 0x04000002, 0x04000002},
 	{0x0000a508, 0x0a000020, 0x0a000020, 0x08000004, 0x08000004},
 	{0x0000a50c, 0x10000023, 0x10000023, 0x0b000200, 0x0b000200},
-	{0x0000a510, 0x15000028, 0x15000028, 0x0f000202, 0x0f000202},
-	{0x0000a514, 0x1b00002b, 0x1b00002b, 0x12000400, 0x12000400},
-	{0x0000a518, 0x1f020028, 0x1f020028, 0x16000402, 0x16000402},
-	{0x0000a51c, 0x2502002b, 0x2502002b, 0x19000404, 0x19000404},
-	{0x0000a520, 0x2a04002a, 0x2a04002a, 0x1c000603, 0x1c000603},
-	{0x0000a524, 0x2e06002a, 0x2e06002a, 0x21000a02, 0x21000a02},
-	{0x0000a528, 0x3302202d, 0x3302202d, 0x25000a04, 0x25000a04},
-	{0x0000a52c, 0x3804202c, 0x3804202c, 0x28000a20, 0x28000a20},
-	{0x0000a530, 0x3c06202c, 0x3c06202c, 0x2c000e20, 0x2c000e20},
-	{0x0000a534, 0x4108202d, 0x4108202d, 0x30000e22, 0x30000e22},
-	{0x0000a538, 0x4506402d, 0x4506402d, 0x34000e24, 0x34000e24},
-	{0x0000a53c, 0x4906222d, 0x4906222d, 0x38001640, 0x38001640},
-	{0x0000a540, 0x4d062231, 0x4d062231, 0x3c001660, 0x3c001660},
-	{0x0000a544, 0x50082231, 0x50082231, 0x3f001861, 0x3f001861},
-	{0x0000a548, 0x5608422e, 0x5608422e, 0x43001a81, 0x43001a81},
-	{0x0000a54c, 0x5a08442e, 0x5a08442e, 0x47001a83, 0x47001a83},
-	{0x0000a550, 0x5e0a4431, 0x5e0a4431, 0x4a001c84, 0x4a001c84},
-	{0x0000a554, 0x640a4432, 0x640a4432, 0x4e001ce3, 0x4e001ce3},
-	{0x0000a558, 0x680a4434, 0x680a4434, 0x52001ce5, 0x52001ce5},
-	{0x0000a55c, 0x6c0a6434, 0x6c0a6434, 0x56001ce9, 0x56001ce9},
-	{0x0000a560, 0x6f0a6633, 0x6f0a6633, 0x5a001ceb, 0x5a001ceb},
-	{0x0000a564, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
-	{0x0000a568, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
-	{0x0000a56c, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
-	{0x0000a570, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
-	{0x0000a574, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
-	{0x0000a578, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
-	{0x0000a57c, 0x730c6634, 0x730c6634, 0x5d001eec, 0x5d001eec},
+	{0x0000a510, 0x16000220, 0x16000220, 0x0f000202, 0x0f000202},
+	{0x0000a514, 0x1c000223, 0x1c000223, 0x12000400, 0x12000400},
+	{0x0000a518, 0x21002220, 0x21002220, 0x16000402, 0x16000402},
+	{0x0000a51c, 0x27002223, 0x27002223, 0x19000404, 0x19000404},
+	{0x0000a520, 0x2b022220, 0x2b022220, 0x1c000603, 0x1c000603},
+	{0x0000a524, 0x2f022222, 0x2f022222, 0x21000a02, 0x21000a02},
+	{0x0000a528, 0x34022225, 0x34022225, 0x25000a04, 0x25000a04},
+	{0x0000a52c, 0x3a02222a, 0x3a02222a, 0x28000a20, 0x28000a20},
+	{0x0000a530, 0x3e02222c, 0x3e02222c, 0x2c000e20, 0x2c000e20},
+	{0x0000a534, 0x4202242a, 0x4202242a, 0x30000e22, 0x30000e22},
+	{0x0000a538, 0x4702244a, 0x4702244a, 0x34000e24, 0x34000e24},
+	{0x0000a53c, 0x4b02244c, 0x4b02244c, 0x38001640, 0x38001640},
+	{0x0000a540, 0x4e02246c, 0x4e02246c, 0x3c001660, 0x3c001660},
+	{0x0000a544, 0x52022470, 0x52022470, 0x3f001861, 0x3f001861},
+	{0x0000a548, 0x55022490, 0x55022490, 0x43001a81, 0x43001a81},
+	{0x0000a54c, 0x59022492, 0x59022492, 0x47001a83, 0x47001a83},
+	{0x0000a550, 0x5d022692, 0x5d022692, 0x4a001c84, 0x4a001c84},
+	{0x0000a554, 0x61022892, 0x61022892, 0x4e001ce3, 0x4e001ce3},
+	{0x0000a558, 0x65024890, 0x65024890, 0x52001ce5, 0x52001ce5},
+	{0x0000a55c, 0x69024892, 0x69024892, 0x56001ce9, 0x56001ce9},
+	{0x0000a560, 0x6e024c92, 0x6e024c92, 0x5a001ceb, 0x5a001ceb},
+	{0x0000a564, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
+	{0x0000a568, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
+	{0x0000a56c, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
+	{0x0000a570, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
+	{0x0000a574, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
+	{0x0000a578, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
+	{0x0000a57c, 0x74026e92, 0x74026e92, 0x5d001eec, 0x5d001eec},
 	{0x0000a580, 0x00800000, 0x00800000, 0x00800000, 0x00800000},
 	{0x0000a584, 0x06800003, 0x06800003, 0x04800002, 0x04800002},
 	{0x0000a588, 0x0a800020, 0x0a800020, 0x08800004, 0x08800004},
 	{0x0000a58c, 0x10800023, 0x10800023, 0x0b800200, 0x0b800200},
-	{0x0000a590, 0x15800028, 0x15800028, 0x0f800202, 0x0f800202},
-	{0x0000a594, 0x1b80002b, 0x1b80002b, 0x12800400, 0x12800400},
-	{0x0000a598, 0x1f820028, 0x1f820028, 0x16800402, 0x16800402},
-	{0x0000a59c, 0x2582002b, 0x2582002b, 0x19800404, 0x19800404},
-	{0x0000a5a0, 0x2a84002a, 0x2a84002a, 0x1c800603, 0x1c800603},
-	{0x0000a5a4, 0x2e86002a, 0x2e86002a, 0x21800a02, 0x21800a02},
-	{0x0000a5a8, 0x3382202d, 0x3382202d, 0x25800a04, 0x25800a04},
-	{0x0000a5ac, 0x3884202c, 0x3884202c, 0x28800a20, 0x28800a20},
-	{0x0000a5b0, 0x3c86202c, 0x3c86202c, 0x2c800e20, 0x2c800e20},
-	{0x0000a5b4, 0x4188202d, 0x4188202d, 0x30800e22, 0x30800e22},
-	{0x0000a5b8, 0x4586402d, 0x4586402d, 0x34800e24, 0x34800e24},
-	{0x0000a5bc, 0x4986222d, 0x4986222d, 0x38801640, 0x38801640},
-	{0x0000a5c0, 0x4d862231, 0x4d862231, 0x3c801660, 0x3c801660},
-	{0x0000a5c4, 0x50882231, 0x50882231, 0x3f801861, 0x3f801861},
-	{0x0000a5c8, 0x5688422e, 0x5688422e, 0x43801a81, 0x43801a81},
-	{0x0000a5cc, 0x5a88442e, 0x5a88442e, 0x47801a83, 0x47801a83},
-	{0x0000a5d0, 0x5e8a4431, 0x5e8a4431, 0x4a801c84, 0x4a801c84},
-	{0x0000a5d4, 0x648a4432, 0x648a4432, 0x4e801ce3, 0x4e801ce3},
-	{0x0000a5d8, 0x688a4434, 0x688a4434, 0x52801ce5, 0x52801ce5},
-	{0x0000a5dc, 0x6c8a6434, 0x6c8a6434, 0x56801ce9, 0x56801ce9},
-	{0x0000a5e0, 0x6f8a6633, 0x6f8a6633, 0x5a801ceb, 0x5a801ceb},
-	{0x0000a5e4, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
-	{0x0000a5e8, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
-	{0x0000a5ec, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
-	{0x0000a5f0, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
-	{0x0000a5f4, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
-	{0x0000a5f8, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
-	{0x0000a5fc, 0x738c6634, 0x738c6634, 0x5d801eec, 0x5d801eec},
+	{0x0000a590, 0x16800220, 0x16800220, 0x0f800202, 0x0f800202},
+	{0x0000a594, 0x1c800223, 0x1c800223, 0x12800400, 0x12800400},
+	{0x0000a598, 0x21802220, 0x21802220, 0x16800402, 0x16800402},
+	{0x0000a59c, 0x27802223, 0x27802223, 0x19800404, 0x19800404},
+	{0x0000a5a0, 0x2b822220, 0x2b822220, 0x1c800603, 0x1c800603},
+	{0x0000a5a4, 0x2f822222, 0x2f822222, 0x21800a02, 0x21800a02},
+	{0x0000a5a8, 0x34822225, 0x34822225, 0x25800a04, 0x25800a04},
+	{0x0000a5ac, 0x3a82222a, 0x3a82222a, 0x28800a20, 0x28800a20},
+	{0x0000a5b0, 0x3e82222c, 0x3e82222c, 0x2c800e20, 0x2c800e20},
+	{0x0000a5b4, 0x4282242a, 0x4282242a, 0x30800e22, 0x30800e22},
+	{0x0000a5b8, 0x4782244a, 0x4782244a, 0x34800e24, 0x34800e24},
+	{0x0000a5bc, 0x4b82244c, 0x4b82244c, 0x38801640, 0x38801640},
+	{0x0000a5c0, 0x4e82246c, 0x4e82246c, 0x3c801660, 0x3c801660},
+	{0x0000a5c4, 0x52822470, 0x52822470, 0x3f801861, 0x3f801861},
+	{0x0000a5c8, 0x55822490, 0x55822490, 0x43801a81, 0x43801a81},
+	{0x0000a5cc, 0x59822492, 0x59822492, 0x47801a83, 0x47801a83},
+	{0x0000a5d0, 0x5d822692, 0x5d822692, 0x4a801c84, 0x4a801c84},
+	{0x0000a5d4, 0x61822892, 0x61822892, 0x4e801ce3, 0x4e801ce3},
+	{0x0000a5d8, 0x65824890, 0x65824890, 0x52801ce5, 0x52801ce5},
+	{0x0000a5dc, 0x69824892, 0x69824892, 0x56801ce9, 0x56801ce9},
+	{0x0000a5e0, 0x6e824c92, 0x6e824c92, 0x5a801ceb, 0x5a801ceb},
+	{0x0000a5e4, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
+	{0x0000a5e8, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
+	{0x0000a5ec, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
+	{0x0000a5f0, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
+	{0x0000a5f4, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
+	{0x0000a5f8, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
+	{0x0000a5fc, 0x74826e92, 0x74826e92, 0x5d801eec, 0x5d801eec},
 	{0x0000a600, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
 	{0x0000a604, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
-	{0x0000a608, 0x01804601, 0x01804601, 0x00000000, 0x00000000},
-	{0x0000a60c, 0x01804601, 0x01804601, 0x00000000, 0x00000000},
-	{0x0000a610, 0x01804601, 0x01804601, 0x00000000, 0x00000000},
-	{0x0000a614, 0x01804601, 0x01804601, 0x01404000, 0x01404000},
-	{0x0000a618, 0x01804601, 0x01804601, 0x01404501, 0x01404501},
-	{0x0000a61c, 0x01804601, 0x01804601, 0x02008501, 0x02008501},
-	{0x0000a620, 0x03408d02, 0x03408d02, 0x0280ca03, 0x0280ca03},
-	{0x0000a624, 0x0300cc03, 0x0300cc03, 0x03010c04, 0x03010c04},
-	{0x0000a628, 0x03410d04, 0x03410d04, 0x04014c04, 0x04014c04},
-	{0x0000a62c, 0x03410d04, 0x03410d04, 0x04015005, 0x04015005},
-	{0x0000a630, 0x03410d04, 0x03410d04, 0x04015005, 0x04015005},
-	{0x0000a634, 0x03410d04, 0x03410d04, 0x04015005, 0x04015005},
-	{0x0000a638, 0x03410d04, 0x03410d04, 0x04015005, 0x04015005},
-	{0x0000a63c, 0x03410d04, 0x03410d04, 0x04015005, 0x04015005},
-	{0x0000b2dc, 0x000cfff0, 0x000cfff0, 0x03aaa352, 0x03aaa352},
-	{0x0000b2e0, 0x000f0000, 0x000f0000, 0x03ccc584, 0x03ccc584},
-	{0x0000b2e4, 0x03f00000, 0x03f00000, 0x03f0f800, 0x03f0f800},
+	{0x0000a608, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x0000a60c, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x0000a610, 0x00000000, 0x00000000, 0x00000000, 0x00000000},
+	{0x0000a614, 0x02004000, 0x02004000, 0x01404000, 0x01404000},
+	{0x0000a618, 0x02004801, 0x02004801, 0x01404501, 0x01404501},
+	{0x0000a61c, 0x02808a02, 0x02808a02, 0x02008501, 0x02008501},
+	{0x0000a620, 0x0380ce03, 0x0380ce03, 0x0280ca03, 0x0280ca03},
+	{0x0000a624, 0x04411104, 0x04411104, 0x03010c04, 0x03010c04},
+	{0x0000a628, 0x04411104, 0x04411104, 0x04014c04, 0x04014c04},
+	{0x0000a62c, 0x04411104, 0x04411104, 0x04015005, 0x04015005},
+	{0x0000a630, 0x04411104, 0x04411104, 0x04015005, 0x04015005},
+	{0x0000a634, 0x04411104, 0x04411104, 0x04015005, 0x04015005},
+	{0x0000a638, 0x04411104, 0x04411104, 0x04015005, 0x04015005},
+	{0x0000a63c, 0x04411104, 0x04411104, 0x04015005, 0x04015005},
+	{0x0000b2dc, 0x00033800, 0x00033800, 0x03aaa352, 0x03aaa352},
+	{0x0000b2e0, 0x0003c000, 0x0003c000, 0x03ccc584, 0x03ccc584},
+	{0x0000b2e4, 0x03fc0000, 0x03fc0000, 0x03f0f800, 0x03f0f800},
 	{0x0000b2e8, 0x00000000, 0x00000000, 0x03ff0000, 0x03ff0000},
-	{0x0000c2dc, 0x000cfff0, 0x000cfff0, 0x03aaa352, 0x03aaa352},
-	{0x0000c2e0, 0x000f0000, 0x000f0000, 0x03ccc584, 0x03ccc584},
-	{0x0000c2e4, 0x03f00000, 0x03f00000, 0x03f0f800, 0x03f0f800},
+	{0x0000c2dc, 0x00033800, 0x00033800, 0x03aaa352, 0x03aaa352},
+	{0x0000c2e0, 0x0003c000, 0x0003c000, 0x03ccc584, 0x03ccc584},
+	{0x0000c2e4, 0x03fc0000, 0x03fc0000, 0x03f0f800, 0x03f0f800},
 	{0x0000c2e8, 0x00000000, 0x00000000, 0x03ff0000, 0x03ff0000},
 	{0x00016044, 0x012492d4, 0x012492d4, 0x012492d4, 0x012492d4},
-	{0x00016048, 0x61200001, 0x61200001, 0x66480001, 0x66480001},
+	{0x00016048, 0x66480001, 0x66480001, 0x66480001, 0x66480001},
 	{0x00016068, 0x6db6db6c, 0x6db6db6c, 0x6db6db6c, 0x6db6db6c},
 	{0x00016444, 0x012492d4, 0x012492d4, 0x012492d4, 0x012492d4},
-	{0x00016448, 0x61200001, 0x61200001, 0x66480001, 0x66480001},
+	{0x00016448, 0x66480001, 0x66480001, 0x66480001, 0x66480001},
 	{0x00016468, 0x6db6db6c, 0x6db6db6c, 0x6db6db6c, 0x6db6db6c},
 	{0x00016844, 0x012492d4, 0x012492d4, 0x012492d4, 0x012492d4},
-	{0x00016848, 0x61200001, 0x61200001, 0x66480001, 0x66480001},
+	{0x00016848, 0x66480001, 0x66480001, 0x66480001, 0x66480001},
 	{0x00016868, 0x6db6db6c, 0x6db6db6c, 0x6db6db6c, 0x6db6db6c},
 };
 

[ 094/101] x86, mm: Find_early_table_space based on ranges that are actually being mapped

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Jacob Shin <jacob.shin@amd.com>

commit 844ab6f993b1d32eb40512503d35ff6ad0c57030 upstream.

Current logic finds enough space for direct mapping page tables from 0
to end. Instead, we only need to find enough space to cover mr[0].start
to mr[nr_range].end -- the range that is actually being mapped by
init_memory_mapping()

This is needed after 1bbbbe779aabe1f0768c2bf8f8c0a5583679b54a, to address
the panic reported here:

  https://lkml.org/lkml/2012/10/20/160
  https://lkml.org/lkml/2012/10/21/157

Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Link: http://lkml.kernel.org/r/20121024195311.GB11779@jshin-Toonie
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/mm/init.c |   70 +++++++++++++++++++++++++++++++----------------------
 1 file changed, 41 insertions(+), 29 deletions(-)

--- a/arch/x86/mm/init.c
+++ b/arch/x86/mm/init.c
@@ -29,36 +29,54 @@ int direct_gbpages
 #endif
 ;
 
-static void __init find_early_table_space(unsigned long end, int use_pse,
-					  int use_gbpages)
+struct map_range {
+	unsigned long start;
+	unsigned long end;
+	unsigned page_size_mask;
+};
+
+/*
+ * First calculate space needed for kernel direct mapping page tables to cover
+ * mr[0].start to mr[nr_range - 1].end, while accounting for possible 2M and 1GB
+ * pages. Then find enough contiguous space for those page tables.
+ */
+static void __init find_early_table_space(struct map_range *mr, int nr_range)
 {
-	unsigned long puds, pmds, ptes, tables, start = 0, good_end = end;
+	int i;
+	unsigned long puds = 0, pmds = 0, ptes = 0, tables;
+	unsigned long start = 0, good_end;
 	phys_addr_t base;
 
-	puds = (end + PUD_SIZE - 1) >> PUD_SHIFT;
-	tables = roundup(puds * sizeof(pud_t), PAGE_SIZE);
+	for (i = 0; i < nr_range; i++) {
+		unsigned long range, extra;
 
-	if (use_gbpages) {
-		unsigned long extra;
+		range = mr[i].end - mr[i].start;
+		puds += (range + PUD_SIZE - 1) >> PUD_SHIFT;
 
-		extra = end - ((end>>PUD_SHIFT) << PUD_SHIFT);
-		pmds = (extra + PMD_SIZE - 1) >> PMD_SHIFT;
-	} else
-		pmds = (end + PMD_SIZE - 1) >> PMD_SHIFT;
-
-	tables += roundup(pmds * sizeof(pmd_t), PAGE_SIZE);
+		if (mr[i].page_size_mask & (1 << PG_LEVEL_1G)) {
+			extra = range - ((range >> PUD_SHIFT) << PUD_SHIFT);
+			pmds += (extra + PMD_SIZE - 1) >> PMD_SHIFT;
+		} else {
+			pmds += (range + PMD_SIZE - 1) >> PMD_SHIFT;
+		}
 
-	if (use_pse) {
-		unsigned long extra;
-
-		extra = end - ((end>>PMD_SHIFT) << PMD_SHIFT);
+		if (mr[i].page_size_mask & (1 << PG_LEVEL_2M)) {
+			extra = range - ((range >> PMD_SHIFT) << PMD_SHIFT);
 #ifdef CONFIG_X86_32
-		extra += PMD_SIZE;
+			extra += PMD_SIZE;
 #endif
-		ptes = (extra + PAGE_SIZE - 1) >> PAGE_SHIFT;
-	} else
-		ptes = (end + PAGE_SIZE - 1) >> PAGE_SHIFT;
+			/* The first 2/4M doesn't use large pages. */
+			if (mr[i].start < PMD_SIZE)
+				extra += range;
+
+			ptes += (extra + PAGE_SIZE - 1) >> PAGE_SHIFT;
+		} else {
+			ptes += (range + PAGE_SIZE - 1) >> PAGE_SHIFT;
+		}
+	}
 
+	tables = roundup(puds * sizeof(pud_t), PAGE_SIZE);
+	tables += roundup(pmds * sizeof(pmd_t), PAGE_SIZE);
 	tables += roundup(ptes * sizeof(pte_t), PAGE_SIZE);
 
 #ifdef CONFIG_X86_32
@@ -76,7 +94,7 @@ static void __init find_early_table_spac
 	pgt_buf_top = pgt_buf_start + (tables >> PAGE_SHIFT);
 
 	printk(KERN_DEBUG "kernel direct mapping tables up to %#lx @ [mem %#010lx-%#010lx]\n",
-		end - 1, pgt_buf_start << PAGE_SHIFT,
+		mr[nr_range - 1].end - 1, pgt_buf_start << PAGE_SHIFT,
 		(pgt_buf_top << PAGE_SHIFT) - 1);
 }
 
@@ -85,12 +103,6 @@ void __init native_pagetable_reserve(u64
 	memblock_reserve(start, end - start);
 }
 
-struct map_range {
-	unsigned long start;
-	unsigned long end;
-	unsigned page_size_mask;
-};
-
 #ifdef CONFIG_X86_32
 #define NR_RANGE_MR 3
 #else /* CONFIG_X86_64 */
@@ -263,7 +275,7 @@ unsigned long __init_refok init_memory_m
 	 * nodes are discovered.
 	 */
 	if (!after_bootmem)
-		find_early_table_space(end, use_pse, use_gbpages);
+		find_early_table_space(mr, nr_range);
 
 	for (i = 0; i < nr_range; i++)
 		ret = kernel_physical_mapping_init(mr[i].start, mr[i].end,

[ 095/101] x86, mm: Undo incorrect revert in arch/x86/mm/init.c

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Yinghai Lu <yinghai@kernel.org>

commit f82f64dd9f485e13f29f369772d4a0e868e5633a upstream.

Commit

    844ab6f9 x86, mm: Find_early_table_space based on ranges that are actually being mapped

added back some lines back wrongly that has been removed in commit

    7b16bbf97 Revert "x86/mm: Fix the size calculation of mapping tables"

remove them again.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQW_vuaYQbmagVnxT2DGsYc=9tNeAbdBq53sYkitPOwxSQ@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/mm/init.c |    4 ----
 1 file changed, 4 deletions(-)

--- a/arch/x86/mm/init.c
+++ b/arch/x86/mm/init.c
@@ -65,10 +65,6 @@ static void __init find_early_table_spac
 #ifdef CONFIG_X86_32
 			extra += PMD_SIZE;
 #endif
-			/* The first 2/4M doesn't use large pages. */
-			if (mr[i].start < PMD_SIZE)
-				extra += range;
-
 			ptes += (extra + PAGE_SIZE - 1) >> PAGE_SHIFT;
 		} else {
 			ptes += (range + PAGE_SIZE - 1) >> PAGE_SHIFT;

[ 096/101] cfg80211/mac80211: avoid state mishmash on deauth

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Stanislaw Gruszka <sgruszka@redhat.com>

commit 6863255bd0e48bc41ae5a066d5c771801e92735a upstream.

Avoid situation when we are on associate state in mac80211 and
on disassociate state in cfg80211. This can results on crash
during modules unload (like showed on this thread:
http://marc.info/?t=134373976300001&r=1&w=2) and possibly other
problems.

Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 include/net/cfg80211.h |    1 +
 net/mac80211/mlme.c    |    5 +++--
 net/wireless/mlme.c    |   12 +++---------
 3 files changed, 7 insertions(+), 11 deletions(-)

--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1217,6 +1217,7 @@ struct cfg80211_deauth_request {
 	const u8 *ie;
 	size_t ie_len;
 	u16 reason_code;
+	bool local_state_change;
 };
 
 /**
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -3467,6 +3467,7 @@ int ieee80211_mgd_deauth(struct ieee8021
 {
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
 	u8 frame_buf[DEAUTH_DISASSOC_LEN];
+	bool tx = !req->local_state_change;
 
 	mutex_lock(&ifmgd->mtx);
 
@@ -3483,11 +3484,11 @@ int ieee80211_mgd_deauth(struct ieee8021
 	if (ifmgd->associated &&
 	    ether_addr_equal(ifmgd->associated->bssid, req->bssid))
 		ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
-				       req->reason_code, true, frame_buf);
+				       req->reason_code, tx, frame_buf);
 	else
 		ieee80211_send_deauth_disassoc(sdata, req->bssid,
 					       IEEE80211_STYPE_DEAUTH,
-					       req->reason_code, true,
+					       req->reason_code, tx,
 					       frame_buf);
 	mutex_unlock(&ifmgd->mtx);
 
--- a/net/wireless/mlme.c
+++ b/net/wireless/mlme.c
@@ -457,20 +457,14 @@ int __cfg80211_mlme_deauth(struct cfg802
 		.reason_code = reason,
 		.ie = ie,
 		.ie_len = ie_len,
+		.local_state_change = local_state_change,
 	};
 
 	ASSERT_WDEV_LOCK(wdev);
 
-	if (local_state_change) {
-		if (wdev->current_bss &&
-		    ether_addr_equal(wdev->current_bss->pub.bssid, bssid)) {
-			cfg80211_unhold_bss(wdev->current_bss);
-			cfg80211_put_bss(&wdev->current_bss->pub);
-			wdev->current_bss = NULL;
-		}
-
+	if (local_state_change && (!wdev->current_bss ||
+	    !ether_addr_equal(wdev->current_bss->pub.bssid, bssid)))
 		return 0;
-	}
 
 	return rdev->ops->deauth(&rdev->wiphy, dev, &req);
 }

[ 097/101] efi: Defer freeing boot services memory until after ACPI init

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Josh Triplett <josh@joshtriplett.org>

commit 785107923a83d8456bbd8564e288a24d84109a46 upstream.

Some new ACPI 5.0 tables reference resources stored in boot services
memory, so keep that memory around until we have ACPI and can extract
data from it.

Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/baaa6d44bdc4eb0c58e5d1b4ccd2c729f854ac55.1348876882.git.josh@joshtriplett.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/platform/efi/efi.c |   31 ++++++++++++++++++-------------
 include/linux/efi.h         |    5 +++++
 init/main.c                 |    3 +++
 3 files changed, 26 insertions(+), 13 deletions(-)

--- a/arch/x86/platform/efi/efi.c
+++ b/arch/x86/platform/efi/efi.c
@@ -419,10 +419,21 @@ void __init efi_reserve_boot_services(vo
 	}
 }
 
-static void __init efi_free_boot_services(void)
+static void __init efi_unmap_memmap(void)
+{
+	if (memmap.map) {
+		early_iounmap(memmap.map, memmap.nr_map * memmap.desc_size);
+		memmap.map = NULL;
+	}
+}
+
+void __init efi_free_boot_services(void)
 {
 	void *p;
 
+	if (!efi_native)
+		return;
+
 	for (p = memmap.map; p < memmap.map_end; p += memmap.desc_size) {
 		efi_memory_desc_t *md = p;
 		unsigned long long start = md->phys_addr;
@@ -438,6 +449,8 @@ static void __init efi_free_boot_service
 
 		free_bootmem_late(start, size);
 	}
+
+	efi_unmap_memmap();
 }
 
 static int __init efi_systab_init(void *phys)
@@ -787,8 +800,10 @@ void __init efi_enter_virtual_mode(void)
 	 * non-native EFI
 	 */
 
-	if (!efi_native)
-		goto out;
+	if (!efi_native) {
+		efi_unmap_memmap();
+		return;
+	}
 
 	/* Merge contiguous regions of the same type and attribute */
 	for (p = memmap.map; p < memmap.map_end; p += memmap.desc_size) {
@@ -878,13 +893,6 @@ void __init efi_enter_virtual_mode(void)
 	}
 
 	/*
-	 * Thankfully, it does seem that no runtime services other than
-	 * SetVirtualAddressMap() will touch boot services code, so we can
-	 * get rid of it all at this point
-	 */
-	efi_free_boot_services();
-
-	/*
 	 * Now that EFI is in virtual mode, update the function
 	 * pointers in the runtime service table to the new virtual addresses.
 	 *
@@ -907,9 +915,6 @@ void __init efi_enter_virtual_mode(void)
 	if (__supported_pte_mask & _PAGE_NX)
 		runtime_code_page_mkexec();
 
-out:
-	early_iounmap(memmap.map, memmap.nr_map * memmap.desc_size);
-	memmap.map = NULL;
 	kfree(new_memmap);
 }
 
--- a/include/linux/efi.h
+++ b/include/linux/efi.h
@@ -496,6 +496,11 @@ extern void efi_map_pal_code (void);
 extern void efi_memmap_walk (efi_freemem_callback_t callback, void *arg);
 extern void efi_gettimeofday (struct timespec *ts);
 extern void efi_enter_virtual_mode (void);	/* switch EFI to virtual mode, if possible */
+#ifdef CONFIG_X86
+extern void efi_free_boot_services(void);
+#else
+static inline void efi_free_boot_services(void) {}
+#endif
 extern u64 efi_get_iobase (void);
 extern u32 efi_mem_type (unsigned long phys_addr);
 extern u64 efi_mem_attributes (unsigned long phys_addr);
--- a/init/main.c
+++ b/init/main.c
@@ -631,6 +631,9 @@ asmlinkage void __init start_kernel(void
 	acpi_early_init(); /* before LAPIC and SMP init */
 	sfi_init_late();
 
+	if (efi_enabled)
+		efi_free_boot_services();
+
 	ftrace_init();
 
 	/* Do the rest non-__init'ed, we're now alive */

[ 098/101] x86: efi: Turn off efi_enabled after setup on mixed fw/kernel

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Olof Johansson <olof@lixom.net>

commit 5189c2a7c7769ee9d037d76c1a7b8550ccf3481c upstream.

When 32-bit EFI is used with 64-bit kernel (or vice versa), turn off
efi_enabled once setup is done. Beyond setup, it is normally used to
determine if runtime services are available and we will have none.

This will resolve issues stemming from efivars modprobe panicking on a
32/64-bit setup, as well as some reboot issues on similar setups.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45991

Reported-by: Marko Kohtala <marko.kohtala@gmail.com>
Reported-by: Maxim Kammerer <mk@dee.su>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/include/asm/efi.h  |    1 +
 arch/x86/kernel/setup.c     |   12 ++++++++++++
 arch/x86/platform/efi/efi.c |   18 ++++++++++--------
 3 files changed, 23 insertions(+), 8 deletions(-)

--- a/arch/x86/include/asm/efi.h
+++ b/arch/x86/include/asm/efi.h
@@ -98,6 +98,7 @@ extern void efi_set_executable(efi_memor
 extern int efi_memblock_x86_reserve_range(void);
 extern void efi_call_phys_prelog(void);
 extern void efi_call_phys_epilog(void);
+extern void efi_unmap_memmap(void);
 
 #ifndef CONFIG_EFI
 /*
--- a/arch/x86/kernel/setup.c
+++ b/arch/x86/kernel/setup.c
@@ -1047,6 +1047,18 @@ void __init setup_arch(char **cmdline_p)
 	mcheck_init();
 
 	arch_init_ideal_nops();
+
+#ifdef CONFIG_EFI
+	/* Once setup is done above, disable efi_enabled on mismatched
+	 * firmware/kernel archtectures since there is no support for
+	 * runtime services.
+	 */
+	if (efi_enabled && IS_ENABLED(CONFIG_X86_64) != efi_64bit) {
+		pr_info("efi: Setup done, disabling due to 32/64-bit mismatch\n");
+		efi_unmap_memmap();
+		efi_enabled = 0;
+	}
+#endif
 }
 
 #ifdef CONFIG_X86_32
--- a/arch/x86/platform/efi/efi.c
+++ b/arch/x86/platform/efi/efi.c
@@ -69,11 +69,15 @@ EXPORT_SYMBOL(efi);
 struct efi_memory_map memmap;
 
 bool efi_64bit;
-static bool efi_native;
 
 static struct efi efi_phys __initdata;
 static efi_system_table_t efi_systab __initdata;
 
+static inline bool efi_is_native(void)
+{
+	return IS_ENABLED(CONFIG_X86_64) == efi_64bit;
+}
+
 static int __init setup_noefi(char *arg)
 {
 	efi_enabled = 0;
@@ -419,7 +423,7 @@ void __init efi_reserve_boot_services(vo
 	}
 }
 
-static void __init efi_unmap_memmap(void)
+void __init efi_unmap_memmap(void)
 {
 	if (memmap.map) {
 		early_iounmap(memmap.map, memmap.nr_map * memmap.desc_size);
@@ -431,7 +435,7 @@ void __init efi_free_boot_services(void)
 {
 	void *p;
 
-	if (!efi_native)
+	if (!efi_is_native())
 		return;
 
 	for (p = memmap.map; p < memmap.map_end; p += memmap.desc_size) {
@@ -683,12 +687,10 @@ void __init efi_init(void)
 		return;
 	}
 	efi_phys.systab = (efi_system_table_t *)boot_params.efi_info.efi_systab;
-	efi_native = !efi_64bit;
 #else
 	efi_phys.systab = (efi_system_table_t *)
 			  (boot_params.efi_info.efi_systab |
 			  ((__u64)boot_params.efi_info.efi_systab_hi<<32));
-	efi_native = efi_64bit;
 #endif
 
 	if (efi_systab_init(efi_phys.systab)) {
@@ -722,7 +724,7 @@ void __init efi_init(void)
 	 * that doesn't match the kernel 32/64-bit mode.
 	 */
 
-	if (!efi_native)
+	if (!efi_is_native())
 		pr_info("No EFI runtime due to 32/64-bit mismatch with kernel\n");
 	else if (efi_runtime_init()) {
 		efi_enabled = 0;
@@ -734,7 +736,7 @@ void __init efi_init(void)
 		return;
 	}
 #ifdef CONFIG_X86_32
-	if (efi_native) {
+	if (efi_is_native()) {
 		x86_platform.get_wallclock = efi_get_time;
 		x86_platform.set_wallclock = efi_set_rtc_mmss;
 	}
@@ -800,7 +802,7 @@ void __init efi_enter_virtual_mode(void)
 	 * non-native EFI
 	 */
 
-	if (!efi_native) {
+	if (!efi_is_native()) {
 		efi_unmap_memmap();
 		return;
 	}

[ 099/101] x86, mm: Use memblock memory loop instead of e820_RAM

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Yinghai Lu <yinghai@kernel.org>

commit 1f2ff682ac951ed82cc043cf140d2851084512df upstream.

We need to handle E820_RAM and E820_RESERVED_KERNEL at the same time.

Also memblock has page aligned range for ram, so we could avoid mapping
partial pages.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/kernel/setup.c |   15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

--- a/arch/x86/kernel/setup.c
+++ b/arch/x86/kernel/setup.c
@@ -920,18 +920,19 @@ void __init setup_arch(char **cmdline_p)
 #ifdef CONFIG_X86_64
 	if (max_pfn > max_low_pfn) {
 		int i;
-		for (i = 0; i < e820.nr_map; i++) {
-			struct e820entry *ei = &e820.map[i];
+		unsigned long start, end;
+		unsigned long start_pfn, end_pfn;
 
-			if (ei->addr + ei->size <= 1UL << 32)
-				continue;
+		for_each_mem_pfn_range(i, MAX_NUMNODES, &start_pfn, &end_pfn,
+							 NULL) {
 
-			if (ei->type == E820_RESERVED)
+			end = PFN_PHYS(end_pfn);
+			if (end <= (1UL<<32))
 				continue;
 
+			start = PFN_PHYS(start_pfn);
 			max_pfn_mapped = init_memory_mapping(
-				ei->addr < 1UL << 32 ? 1UL << 32 : ei->addr,
-				ei->addr + ei->size);
+						max((1UL<<32), start), end);
 		}
 
 		/* can we preseve max_low_pfn ?*/

[ 100/101] pnfsblock: fix non-aligned DIO read

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Peng Tao <bergwolf@gmail.com>

commit f742dc4a32587bff50b13dde9d8894b96851951a upstream.

For DIO read, if it is not sector aligned, we should reject it
and resend via MDS. Otherwise there might be data corruption.
Also teach bl_read_pagelist to handle partial page reads for DIO.

Signed-off-by: Peng Tao <tao.peng@emc.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/nfs/blocklayout/blocklayout.c |   77 +++++++++++++++++++++++----------------
 1 file changed, 46 insertions(+), 31 deletions(-)

--- a/fs/nfs/blocklayout/blocklayout.c
+++ b/fs/nfs/blocklayout/blocklayout.c
@@ -242,14 +242,6 @@ bl_end_par_io_read(void *data, int unuse
 	schedule_work(&rdata->task.u.tk_work);
 }
 
-static bool
-bl_check_alignment(u64 offset, u32 len, unsigned long blkmask)
-{
-	if ((offset & blkmask) || (len & blkmask))
-		return false;
-	return true;
-}
-
 static enum pnfs_try_status
 bl_read_pagelist(struct nfs_read_data *rdata)
 {
@@ -260,15 +252,15 @@ bl_read_pagelist(struct nfs_read_data *r
 	sector_t isect, extent_length = 0;
 	struct parallel_io *par;
 	loff_t f_offset = rdata->args.offset;
+	size_t bytes_left = rdata->args.count;
+	unsigned int pg_offset, pg_len;
 	struct page **pages = rdata->args.pages;
 	int pg_index = rdata->args.pgbase >> PAGE_CACHE_SHIFT;
+	const bool is_dio = (header->dreq != NULL);
 
 	dprintk("%s enter nr_pages %u offset %lld count %u\n", __func__,
 	       rdata->pages.npages, f_offset, (unsigned int)rdata->args.count);
 
-	if (!bl_check_alignment(f_offset, rdata->args.count, PAGE_CACHE_MASK))
-		goto use_mds;
-
 	par = alloc_parallel(rdata);
 	if (!par)
 		goto use_mds;
@@ -298,36 +290,53 @@ bl_read_pagelist(struct nfs_read_data *r
 				extent_length = min(extent_length, cow_length);
 			}
 		}
+
+		if (is_dio) {
+			pg_offset = f_offset & ~PAGE_CACHE_MASK;
+			if (pg_offset + bytes_left > PAGE_CACHE_SIZE)
+				pg_len = PAGE_CACHE_SIZE - pg_offset;
+			else
+				pg_len = bytes_left;
+
+			f_offset += pg_len;
+			bytes_left -= pg_len;
+			isect += (pg_offset >> SECTOR_SHIFT);
+		} else {
+			pg_offset = 0;
+			pg_len = PAGE_CACHE_SIZE;
+		}
+
 		hole = is_hole(be, isect);
 		if (hole && !cow_read) {
 			bio = bl_submit_bio(READ, bio);
 			/* Fill hole w/ zeroes w/o accessing device */
 			dprintk("%s Zeroing page for hole\n", __func__);
-			zero_user_segment(pages[i], 0, PAGE_CACHE_SIZE);
+			zero_user_segment(pages[i], pg_offset, pg_len);
 			print_page(pages[i]);
 			SetPageUptodate(pages[i]);
 		} else {
 			struct pnfs_block_extent *be_read;
 
 			be_read = (hole && cow_read) ? cow_read : be;
-			bio = bl_add_page_to_bio(bio, rdata->pages.npages - i,
+			bio = do_add_page_to_bio(bio, rdata->pages.npages - i,
 						 READ,
 						 isect, pages[i], be_read,
-						 bl_end_io_read, par);
+						 bl_end_io_read, par,
+						 pg_offset, pg_len);
 			if (IS_ERR(bio)) {
 				header->pnfs_error = PTR_ERR(bio);
 				bio = NULL;
 				goto out;
 			}
 		}
-		isect += PAGE_CACHE_SECTORS;
+		isect += (pg_len >> SECTOR_SHIFT);
 		extent_length -= PAGE_CACHE_SECTORS;
 	}
 	if ((isect << SECTOR_SHIFT) >= header->inode->i_size) {
 		rdata->res.eof = 1;
-		rdata->res.count = header->inode->i_size - f_offset;
+		rdata->res.count = header->inode->i_size - rdata->args.offset;
 	} else {
-		rdata->res.count = (isect << SECTOR_SHIFT) - f_offset;
+		rdata->res.count = (isect << SECTOR_SHIFT) - rdata->args.offset;
 	}
 out:
 	bl_put_extent(be);
@@ -676,7 +685,7 @@ bl_write_pagelist(struct nfs_write_data
 	struct bio *bio = NULL;
 	struct pnfs_block_extent *be = NULL, *cow_read = NULL;
 	sector_t isect, last_isect = 0, extent_length = 0;
-	struct parallel_io *par = NULL;
+	struct parallel_io *par;
 	loff_t offset = wdata->args.offset;
 	size_t count = wdata->args.count;
 	unsigned int pg_offset, pg_len, saved_len;
@@ -688,10 +697,6 @@ bl_write_pagelist(struct nfs_write_data
 	    NFS_SERVER(header->inode)->pnfs_blksize >> PAGE_CACHE_SHIFT;
 
 	dprintk("%s enter, %Zu@%lld\n", __func__, count, offset);
-	/* Check for alignment first */
-	if (!bl_check_alignment(offset, count, PAGE_CACHE_MASK))
-		goto out_mds;
-
 	/* At this point, wdata->pages is a (sequential) list of nfs_pages.
 	 * We want to write each, and if there is an error set pnfs_error
 	 * to have it redone using nfs.
@@ -1164,32 +1169,42 @@ bl_clear_layoutdriver(struct nfs_server
 	return 0;
 }
 
+static bool
+is_aligned_req(struct nfs_page *req, unsigned int alignment)
+{
+	return IS_ALIGNED(req->wb_offset, alignment) &&
+	       IS_ALIGNED(req->wb_bytes, alignment);
+}
+
 static void
 bl_pg_init_read(struct nfs_pageio_descriptor *pgio, struct nfs_page *req)
 {
-	if (!bl_check_alignment(req->wb_offset, req->wb_bytes, PAGE_CACHE_MASK))
+	if (pgio->pg_dreq != NULL &&
+	    !is_aligned_req(req, SECTOR_SIZE))
 		nfs_pageio_reset_read_mds(pgio);
 	else
 		pnfs_generic_pg_init_read(pgio, req);
 }
 
-static void
-bl_pg_init_write(struct nfs_pageio_descriptor *pgio, struct nfs_page *req)
+static bool
+bl_pg_test_read(struct nfs_pageio_descriptor *pgio, struct nfs_page *prev,
+		struct nfs_page *req)
 {
-	if (!bl_check_alignment(req->wb_offset, req->wb_bytes, PAGE_CACHE_MASK))
-		nfs_pageio_reset_write_mds(pgio);
-	else
-		pnfs_generic_pg_init_write(pgio, req);
+	if (pgio->pg_dreq != NULL &&
+	    !is_aligned_req(req, SECTOR_SIZE))
+		return false;
+
+	return pnfs_generic_pg_test(pgio, prev, req);
 }
 
 static const struct nfs_pageio_ops bl_pg_read_ops = {
 	.pg_init = bl_pg_init_read,
-	.pg_test = pnfs_generic_pg_test,
+	.pg_test = bl_pg_test_read,
 	.pg_doio = pnfs_generic_pg_readpages,
 };
 
 static const struct nfs_pageio_ops bl_pg_write_ops = {
-	.pg_init = bl_pg_init_write,
+	.pg_init = pnfs_generic_pg_init_write,
 	.pg_test = pnfs_generic_pg_test,
 	.pg_doio = pnfs_generic_pg_writepages,
 };

[ 101/101] pnfsblock: fix non-aligned DIO write

[Greg Kroah-Hartman]

3.6-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Peng Tao <bergwolf@gmail.com>

commit 96c9eae638765c2bf2ca4f5a6325484f9bb69aa7 upstream.

For DIO writes, if it is not blocksize aligned, we need to do
internal serialization. It may slow down writers anyway. So we
just bail them out and resend to MDS.

Signed-off-by: Peng Tao <tao.peng@emc.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 fs/nfs/blocklayout/blocklayout.c |   34 +++++++++++++++++++++++++++++++---
 1 file changed, 31 insertions(+), 3 deletions(-)

--- a/fs/nfs/blocklayout/blocklayout.c
+++ b/fs/nfs/blocklayout/blocklayout.c
@@ -685,7 +685,7 @@ bl_write_pagelist(struct nfs_write_data
 	struct bio *bio = NULL;
 	struct pnfs_block_extent *be = NULL, *cow_read = NULL;
 	sector_t isect, last_isect = 0, extent_length = 0;
-	struct parallel_io *par;
+	struct parallel_io *par = NULL;
 	loff_t offset = wdata->args.offset;
 	size_t count = wdata->args.count;
 	unsigned int pg_offset, pg_len, saved_len;
@@ -697,6 +697,13 @@ bl_write_pagelist(struct nfs_write_data
 	    NFS_SERVER(header->inode)->pnfs_blksize >> PAGE_CACHE_SHIFT;
 
 	dprintk("%s enter, %Zu@%lld\n", __func__, count, offset);
+
+	if (header->dreq != NULL &&
+	    (!IS_ALIGNED(offset, NFS_SERVER(header->inode)->pnfs_blksize) ||
+	     !IS_ALIGNED(count, NFS_SERVER(header->inode)->pnfs_blksize))) {
+		dprintk("pnfsblock nonblock aligned DIO writes. Resend MDS\n");
+		goto out_mds;
+	}
 	/* At this point, wdata->pages is a (sequential) list of nfs_pages.
 	 * We want to write each, and if there is an error set pnfs_error
 	 * to have it redone using nfs.
@@ -1197,6 +1204,27 @@ bl_pg_test_read(struct nfs_pageio_descri
 	return pnfs_generic_pg_test(pgio, prev, req);
 }
 
+void
+bl_pg_init_write(struct nfs_pageio_descriptor *pgio, struct nfs_page *req)
+{
+	if (pgio->pg_dreq != NULL &&
+	    !is_aligned_req(req, PAGE_CACHE_SIZE))
+		nfs_pageio_reset_write_mds(pgio);
+	else
+		pnfs_generic_pg_init_write(pgio, req);
+}
+
+static bool
+bl_pg_test_write(struct nfs_pageio_descriptor *pgio, struct nfs_page *prev,
+		 struct nfs_page *req)
+{
+	if (pgio->pg_dreq != NULL &&
+	    !is_aligned_req(req, PAGE_CACHE_SIZE))
+		return false;
+
+	return pnfs_generic_pg_test(pgio, prev, req);
+}
+
 static const struct nfs_pageio_ops bl_pg_read_ops = {
 	.pg_init = bl_pg_init_read,
 	.pg_test = bl_pg_test_read,
@@ -1204,8 +1232,8 @@ static const struct nfs_pageio_ops bl_pg
 };
 
 static const struct nfs_pageio_ops bl_pg_write_ops = {
-	.pg_init = pnfs_generic_pg_init_write,
-	.pg_test = pnfs_generic_pg_test,
+	.pg_init = bl_pg_init_write,
+	.pg_test = bl_pg_test_write,
 	.pg_doio = pnfs_generic_pg_writepages,
 };
 

[PATCH] USB: io_edgeport: remove unused variable

[Paul Bolle]

On Mon, 2012-10-29 at 14:34 -0700, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 3.6.5 release.
> There are 101 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.

A (harmless) unused variable warning was introduced in the 3.6.4
release. That variable was apparently missed when adapting an upstream
commit to context changes. I do not know whether the stable release
process allows for fixing trivial stuff like that. If it does, here's a
patch to remove this variable.


Paul Bolle
---
The stable commit 12ddc74e8e25107eda81aceb74e3311c1480b381
("USB: io_edgeport: fix port-data memory leak") left one variable
unused:
    drivers/usb/serial/io_edgeport.c: In function 'edge_release':
    drivers/usb/serial/io_edgeport.c:3155:6: warning: unused variable 'i' [-Wunused-variable]

Remove this unused variable.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
---
 drivers/usb/serial/io_edgeport.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c
index dca27a5..6c22679 100644
--- a/drivers/usb/serial/io_edgeport.c
+++ b/drivers/usb/serial/io_edgeport.c
@@ -3152,7 +3152,6 @@ static void edge_disconnect(struct usb_serial *serial)
 static void edge_release(struct usb_serial *serial)
 {
 	struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
-	int i;
 
 	dbg("%s", __func__);
 
-- 
1.7.11.7