From: "Pali Rohár" <pali.rohar@gmail.com>
To: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@arndb.de>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
linux-kernel@vger.kernel.org, Valdis.Kletnieks@vt.edu,
Steven Honeyman <stevenhoneyman@gmail.com>,
Jean Delvare <jdelvare@suse.de>,
Gabriele Mazzotta <gabriele.mzt@gmail.com>,
Jochen Eisinger <jochen@penguin-breeder.org>
Subject: Re: [PATCH v4] i8k: Autodetect maximal fan speed and fan RPM multiplier
Date: Sun, 21 Dec 2014 20:56:21 +0100 [thread overview]
Message-ID: <201412212056.21529@pali> (raw)
In-Reply-To: <549716A7.2040207@roeck-us.net>
[-- Attachment #1: Type: Text/Plain, Size: 2440 bytes --]
On Sunday 21 December 2014 19:51:19 Guenter Roeck wrote:
> On 12/21/2014 10:40 AM, Pali Rohár wrote:
> > On Sunday 21 December 2014 19:27:34 Guenter Roeck wrote:
> >> On 12/21/2014 09:23 AM, Pali Rohár wrote:
> >>> This patch adds new function i8k_get_fan_nominal_speed()
> >>> for doing SMM call which will return nominal fan RPM for
> >>> specified fan speed. It returns nominal RPM value at
> >>> which fan operate when speed (0, 1, 2, 3) is set. It
> >>> looks like RPM value is not accurate, but still provides
> >>> very useful information.
> >>>
> >>> First it can be used to validate if certain fan speed
> >>> could be accepted by SMM for setting fan speed and we can
> >>> use this routine to detect maximal fan speed.
> >>>
> >>> Second it returns RPM value, so we can check if value
> >>> looks correct with multiplier 30 or multiplier 1 (until
> >>> now only these two multiplier were used). If RPM value
> >>> with multiplier 30 is too high, then multiplier 1 is
> >>> used.
> >>>
> >>> In case when SMM reports that new function is not
> >>> supported we will fallback to old hardcoded values.
> >>> Maximal fan speed would be 2 and RPM multiplier 30.
> >>>
> >>> Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
> >>> Tested-by: Pali Rohár <pali.rohar@gmail.com>
> >>
> >> Tested-by the submitter is kind of implied.
> >>
> >> Anyway, this patch does not apply to 3.19-rc1, nor to 3.18.
> >> What is your baseline ? Can you rebase to 3.19-rc1 ?
> >> Or do I need to apply some other patch first ?
> >>
> >> Thanks,
> >> Guenter
> >
> > You need to apply these old patches:
> > i8k: Add support for temperature sensor labels
> > i8k: Register only temperature sensors which have labels
> > i8k: Return -ENODATA for invalid temperature
> > i8k: Rework error retries
>
> I think it would make sense to re-send the entire series at
> this point (including my patch and all Reviewed-by: tags).
> Problem is that not all patches have a version number (for
> example there are multiple versions of the label patch, but
> the version I reviewed does not have version information).
> This makes it very difficult to find the correct (reviewed)
> version, and I suspect that Greg may neither have the time
> nor the desire to do it.
>
> Thanks,
> Guenter
Ok, I sent all patches which was not merged to char-misc tree yet
--
Pali Rohár
pali.rohar@gmail.com
[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 198 bytes --]
next prev parent reply other threads:[~2014-12-21 19:56 UTC|newest]
Thread overview: 73+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-12-09 20:06 [PATCH 0/3] i8k: Rework fan_mult and fan_max code Pali Rohár
2014-12-09 20:06 ` [PATCH 1/3] i8k: cosmetic: distinguish between fan speed and fan rpm Pali Rohár
2014-12-09 20:23 ` Guenter Roeck
2014-12-09 20:39 ` Pali Rohár
2014-12-09 22:49 ` Guenter Roeck
2014-12-09 20:07 ` [PATCH 2/3] i8k: Autodetect maximal fan speed and fan RPM multiplier Pali Rohár
2014-12-09 20:20 ` Guenter Roeck
2014-12-09 20:23 ` Pali Rohár
2014-12-09 22:42 ` Guenter Roeck
2014-12-10 11:50 ` Pali Rohár
2014-12-10 14:08 ` Guenter Roeck
2014-12-18 11:13 ` Pali Rohár
2014-12-19 18:33 ` Guenter Roeck
2014-12-09 20:07 ` [PATCH 3/3] i8k: Remove laptop specific config data (fan_mult, fan_max) from driver Pali Rohár
2014-12-10 11:51 ` Pali Rohár
2014-12-10 13:32 ` Gabriele Mazzotta
2014-12-18 11:08 ` Pali Rohár
2014-12-18 15:08 ` Valdis.Kletnieks
2014-12-18 16:34 ` Pali Rohár
2014-12-18 16:44 ` Valdis.Kletnieks
2014-12-25 21:54 ` Gabriele Mazzotta
2014-12-27 14:13 ` Gabriele Mazzotta
2014-12-28 8:22 ` Pali Rohár
2014-12-28 8:28 ` Guenter Roeck
2014-12-28 8:46 ` Pali Rohár
2014-12-28 15:25 ` Gabriele Mazzotta
2014-12-28 15:48 ` Pali Rohár
2014-12-28 16:02 ` Gabriele Mazzotta
2014-12-28 16:07 ` Pali Rohár
2014-12-28 16:17 ` Gabriele Mazzotta
2014-12-29 12:22 ` Pali Rohár
2014-12-29 12:50 ` Gabriele Mazzotta
2014-12-30 7:35 ` Guenter Roeck
2014-12-17 17:54 ` Pali Rohár
2014-12-17 18:20 ` Steven Honeyman
2014-12-18 9:02 ` Valdis.Kletnieks
2014-12-18 11:11 ` Pali Rohár
2014-12-10 13:41 ` Gabriele Mazzotta
2014-12-19 18:04 ` [PATCH v2 1/2] i8k: Autodetect maximal fan speed and fan RPM multiplier Pali Rohár
2014-12-19 18:32 ` Guenter Roeck
2014-12-19 18:51 ` Pali Rohár
2014-12-19 19:28 ` Guenter Roeck
2014-12-20 8:57 ` Pali Rohár
2014-12-20 12:04 ` Guenter Roeck
2014-12-20 12:18 ` Pali Rohár
2014-12-20 12:44 ` Guenter Roeck
2014-12-20 12:54 ` Pali Rohár
2014-12-20 17:20 ` Guenter Roeck
2014-12-20 17:27 ` Steven Honeyman
2014-12-20 18:07 ` Guenter Roeck
2014-12-21 9:06 ` Pali Rohár
2014-12-20 18:38 ` Guenter Roeck
2014-12-21 9:13 ` Pali Rohár
2014-12-21 11:47 ` Guenter Roeck
2014-12-20 19:02 ` Guenter Roeck
2014-12-21 9:15 ` Pali Rohár
2014-12-21 9:20 ` [PATCH v3] " Pali Rohár
2014-12-21 11:57 ` Guenter Roeck
2014-12-21 12:09 ` Pali Rohár
2014-12-21 12:23 ` Guenter Roeck
2014-12-21 16:37 ` Pali Rohár
2014-12-21 16:55 ` Steven Honeyman
2014-12-21 17:25 ` Pali Rohár
2014-12-21 17:23 ` [PATCH v4] " Pali Rohár
2014-12-21 18:27 ` Guenter Roeck
2014-12-21 18:40 ` Pali Rohár
2014-12-21 18:51 ` Guenter Roeck
2014-12-21 19:56 ` Pali Rohár [this message]
2014-12-21 19:51 ` Guenter Roeck
2014-12-22 15:07 ` Pali Rohár
2014-12-23 13:52 ` Guenter Roeck
2014-12-23 19:11 ` Pali Rohár
2014-12-19 18:04 ` [PATCH v2 2/2] i8k: Remove DMI config data for Latitude E6x40 Pali Rohár
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201412212056.21529@pali \
--to=pali.rohar@gmail.com \
--cc=Valdis.Kletnieks@vt.edu \
--cc=arnd@arndb.de \
--cc=gabriele.mzt@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=jdelvare@suse.de \
--cc=jochen@penguin-breeder.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=stevenhoneyman@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).