* [PATCH] phy: marvell: fix LED configuration via marvell,reg-init
@ 2016-06-11 15:21 Clemens Gruber
2016-06-11 15:47 ` Andrew Lunn
2016-06-14 19:24 ` David Miller
0 siblings, 2 replies; 3+ messages in thread
From: Clemens Gruber @ 2016-06-11 15:21 UTC (permalink / raw)
To: netdev
Cc: Andrew Lunn, Florian Fainelli, linux-kernel, David S . Miller,
Sergei Poselenov, Clemens Gruber
Configuring the PHY LED registers for the Marvell 88E1510 and others is
not possible, because regardless of the values in marvell,reg-init, it
is later overridden in m88e1121_config_aneg with a non-standard default.
This patch moves that default configuration to .config_init to allow
setting the LED configuration through marvell,reg-init in the device
tree, which should override said default if it exists.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
---
drivers/net/phy/marvell.c | 38 ++++++++++++++++++++++++++------------
1 file changed, 26 insertions(+), 12 deletions(-)
diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 280e879..79ccc11 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -407,15 +407,7 @@ static int m88e1121_config_aneg(struct phy_device *phydev)
if (err < 0)
return err;
- oldpage = phy_read(phydev, MII_MARVELL_PHY_PAGE);
-
- phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_88E1121_PHY_LED_PAGE);
- phy_write(phydev, MII_88E1121_PHY_LED_CTRL, MII_88E1121_PHY_LED_DEF);
- phy_write(phydev, MII_MARVELL_PHY_PAGE, oldpage);
-
- err = genphy_config_aneg(phydev);
-
- return err;
+ return genphy_config_aneg(phydev);
}
static int m88e1318_config_aneg(struct phy_device *phydev)
@@ -636,6 +628,28 @@ static int m88e1111_config_init(struct phy_device *phydev)
return phy_write(phydev, MII_BMCR, BMCR_RESET);
}
+static int m88e1121_config_init(struct phy_device *phydev)
+{
+ int err, oldpage;
+
+ oldpage = phy_read(phydev, MII_MARVELL_PHY_PAGE);
+
+ err = phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_88E1121_PHY_LED_PAGE);
+ if (err < 0)
+ return err;
+
+ /* Default PHY LED config: LED[0] .. Link, LED[1] .. Activity */
+ err = phy_write(phydev, MII_88E1121_PHY_LED_CTRL,
+ MII_88E1121_PHY_LED_DEF);
+ if (err < 0)
+ return err;
+
+ phy_write(phydev, MII_MARVELL_PHY_PAGE, oldpage);
+
+ /* Set marvell,reg-init configuration from device tree */
+ return marvell_config_init(phydev);
+}
+
static int m88e1510_config_init(struct phy_device *phydev)
{
int err;
@@ -668,7 +682,7 @@ static int m88e1510_config_init(struct phy_device *phydev)
return err;
}
- return marvell_config_init(phydev);
+ return m88e1121_config_init(phydev);
}
static int m88e1118_config_aneg(struct phy_device *phydev)
@@ -1196,7 +1210,7 @@ static struct phy_driver marvell_drivers[] = {
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.probe = marvell_probe,
- .config_init = &marvell_config_init,
+ .config_init = &m88e1121_config_init,
.config_aneg = &m88e1121_config_aneg,
.read_status = &marvell_read_status,
.ack_interrupt = &marvell_ack_interrupt,
@@ -1215,7 +1229,7 @@ static struct phy_driver marvell_drivers[] = {
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.probe = marvell_probe,
- .config_init = &marvell_config_init,
+ .config_init = &m88e1121_config_init,
.config_aneg = &m88e1318_config_aneg,
.read_status = &marvell_read_status,
.ack_interrupt = &marvell_ack_interrupt,
--
2.8.3
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] phy: marvell: fix LED configuration via marvell,reg-init
2016-06-11 15:21 [PATCH] phy: marvell: fix LED configuration via marvell,reg-init Clemens Gruber
@ 2016-06-11 15:47 ` Andrew Lunn
2016-06-14 19:24 ` David Miller
1 sibling, 0 replies; 3+ messages in thread
From: Andrew Lunn @ 2016-06-11 15:47 UTC (permalink / raw)
To: Clemens Gruber
Cc: netdev, Florian Fainelli, linux-kernel, David S . Miller,
Sergei Poselenov
On Sat, Jun 11, 2016 at 05:21:26PM +0200, Clemens Gruber wrote:
> Configuring the PHY LED registers for the Marvell 88E1510 and others is
> not possible, because regardless of the values in marvell,reg-init, it
> is later overridden in m88e1121_config_aneg with a non-standard default.
>
> This patch moves that default configuration to .config_init to allow
> setting the LED configuration through marvell,reg-init in the device
> tree, which should override said default if it exists.
>
> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Andrew
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] phy: marvell: fix LED configuration via marvell,reg-init
2016-06-11 15:21 [PATCH] phy: marvell: fix LED configuration via marvell,reg-init Clemens Gruber
2016-06-11 15:47 ` Andrew Lunn
@ 2016-06-14 19:24 ` David Miller
1 sibling, 0 replies; 3+ messages in thread
From: David Miller @ 2016-06-14 19:24 UTC (permalink / raw)
To: clemens.gruber; +Cc: netdev, andrew, f.fainelli, linux-kernel, sposelenov
From: Clemens Gruber <clemens.gruber@pqgruber.com>
Date: Sat, 11 Jun 2016 17:21:26 +0200
> Configuring the PHY LED registers for the Marvell 88E1510 and others is
> not possible, because regardless of the values in marvell,reg-init, it
> is later overridden in m88e1121_config_aneg with a non-standard default.
>
> This patch moves that default configuration to .config_init to allow
> setting the LED configuration through marvell,reg-init in the device
> tree, which should override said default if it exists.
>
> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Applied.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-06-14 19:24 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-11 15:21 [PATCH] phy: marvell: fix LED configuration via marvell,reg-init Clemens Gruber
2016-06-11 15:47 ` Andrew Lunn
2016-06-14 19:24 ` David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).