* [PATCH V4 1/5] Documentation: Add support for TI System Control Interface (TI-SCI) protocol
2016-10-18 23:08 [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Nishanth Menon
@ 2016-10-18 23:08 ` Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 2/5] firmware: Add basic " Nishanth Menon
` (4 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: Tero Kristo, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman, Nishanth Menon
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those in
newer SoCs in the keystone processor family starting with K2G.
This message protocol is used to communicate between various compute
or processing entities (such as ARM, DSP etc.) with a central system
controller entity.
TI-SCI message protocol provides support for management of various
hardware entities within the SoC.
The message protocol can be found here:
http://processors.wiki.ti.com/index.php/TISCI
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
---
V4: No change, just picked up Rob's Ack from v3.
V3: https://patchwork.kernel.org/patch/9317825/
.../devicetree/bindings/arm/keystone/ti,sci.txt | 81 ++++++++++++++++++++++
MAINTAINERS | 8 +++
2 files changed, 89 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
diff --git a/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
new file mode 100644
index 000000000000..31f5f9a104cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
@@ -0,0 +1,81 @@
+Texas Instruments System Control Interface (TI-SCI) Message Protocol
+--------------------------------------------------------------------
+
+Texas Instrument's processors including those belonging to Keystone generation
+of processors have separate hardware entity which is now responsible for the
+management of the System on Chip (SoC) system. These include various system
+level functions as well.
+
+An example of such an SoC is K2G, which contains the system control hardware
+block called Power Management Micro Controller (PMMC). This hardware block is
+initialized early into boot process and provides services to Operating Systems
+on multiple processors including ones running Linux.
+
+See http://processors.wiki.ti.com/index.php/TISCI for protocol definition.
+
+TI-SCI controller Device Node:
+=============================
+
+The TI-SCI node describes the Texas Instrument's System Controller entity node.
+This parent node may optionally have additional children nodes which describe
+specific functionality such as clocks, power domain, reset or additional
+functionality as may be required for the SoC. This hierarchy also describes the
+relationship between the TI-SCI parent node to the child node.
+
+Required properties:
+-------------------
+- compatible: should be "ti,k2g-sci"
+- mbox-names:
+ "rx" - Mailbox corresponding to receive path
+ "tx" - Mailbox corresponding to transmit path
+
+- mboxes: Mailboxes corresponding to the mbox-names. Each value of the mboxes
+ property should contain a phandle to the mailbox controller device
+ node and an args specifier that will be the phandle to the intended
+ sub-mailbox child node to be used for communication.
+
+See Documentation/devicetree/bindings/mailbox/mailbox.txt for more details
+about the generic mailbox controller and client driver bindings. Also see
+Documentation/devicetree/bindings/mailbox/ti,message-manager.txt for typical
+controller that is used to communicate with this System controllers.
+
+Optional Properties:
+-------------------
+- reg-names:
+ debug_messages - Map the Debug message region
+- reg: register space corresponding to the debug_messages
+- ti,system-reboot-controller: If system reboot can be triggered by SoC reboot
+
+Example (K2G):
+-------------
+ pmmc: pmmc {
+ compatible = "ti,k2g-sci";
+ mbox-names = "rx", "tx";
+ mboxes= <&msgmgr &msgmgr_proxy_pmmc_rx>,
+ <&msgmgr &msgmgr_proxy_pmmc_tx>;
+ reg-names = "debug_messages";
+ reg = <0x02921800 0x800>;
+ };
+
+
+TI-SCI Client Device Node:
+=========================
+
+Client nodes are maintained as children of the relevant TI-SCI device node.
+
+Example (K2G):
+-------------
+ pmmc: pmmc {
+ compatible = "ti,k2g-sci";
+ ...
+
+ my_clk_node: clk_node {
+ ...
+ ...
+ };
+
+ my_pd_node: pd_node {
+ ...
+ ...
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 1cd38a7e0064..2bafadf5747a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11883,6 +11883,14 @@ S: Maintained
F: arch/xtensa/
F: drivers/irqchip/irq-xtensa-*
+Texas Instruments' System Control Interface (TISCI) Protocol Driver
+M: Nishanth Menon <nm@ti.com>
+M: Tero Kristo <t-kristo@ti.com>
+M: Santosh Shilimkar <ssantosh@kernel.org>
+L: linux-arm-kernel@lists.infradead.org
+S: Maintained
+F: Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
+
THANKO'S RAREMONO AM/FM/SW RADIO RECEIVER USB DRIVER
M: Hans Verkuil <hverkuil@xs4all.nl>
L: linux-media@vger.kernel.org
--
2.10.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH V4 2/5] firmware: Add basic support for TI System Control Interface (TI-SCI) protocol
2016-10-18 23:08 [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 1/5] Documentation: Add support for TI System Control Interface (TI-SCI) protocol Nishanth Menon
@ 2016-10-18 23:08 ` Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 3/5] firmware: ti_sci: Add support for Device control Nishanth Menon
` (3 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: Tero Kristo, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman, Nishanth Menon
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.
TI-SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
We introduce the basic registration and query capability for the
driver protocol as part of this change. Subsequent patches add in
functionality specific to the TI-SCI features.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since v3:
- checkpatch fixes for macro after checkpatch.pl update in v4.9-rc1
V3: https://patchwork.kernel.org/patch/9317839/
MAINTAINERS | 2 +
drivers/firmware/Kconfig | 15 +
drivers/firmware/Makefile | 1 +
drivers/firmware/ti_sci.c | 790 +++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 93 ++++
include/linux/soc/ti/ti_sci_protocol.h | 69 +++
6 files changed, 970 insertions(+)
create mode 100644 drivers/firmware/ti_sci.c
create mode 100644 drivers/firmware/ti_sci.h
create mode 100644 include/linux/soc/ti/ti_sci_protocol.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 2bafadf5747a..467b29fafaca 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11890,6 +11890,8 @@ M: Santosh Shilimkar <ssantosh@kernel.org>
L: linux-arm-kernel@lists.infradead.org
S: Maintained
F: Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
+F: drivers/firmware/ti_sci*
+F: include/linux/soc/ti/ti_sci_protocol.h
THANKO'S RAREMONO AM/FM/SW RADIO RECEIVER USB DRIVER
M: Hans Verkuil <hverkuil@xs4all.nl>
diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
index bca172d42c74..9418d7d1b0a5 100644
--- a/drivers/firmware/Kconfig
+++ b/drivers/firmware/Kconfig
@@ -203,6 +203,21 @@ config QCOM_SCM_64
def_bool y
depends on QCOM_SCM && ARM64
+config TI_SCI_PROTOCOL
+ tristate "TI System Control Interface (TISCI) Message Protocol"
+ depends on TI_MESSAGE_MANAGER
+ help
+ TI System Control Interface (TISCI) Message Protocol is used to manage
+ compute systems such as ARM, DSP etc with the system controller in
+ complex System on Chip(SoC) such as those found on certain keystone
+ generation SoC from TI.
+
+ System controller provides various facilities including power
+ management function support.
+
+ This protocol library is used by client drivers to use the features
+ provided by the system controller.
+
config HAVE_ARM_SMCCC
bool
diff --git a/drivers/firmware/Makefile b/drivers/firmware/Makefile
index 898ac41fa8b3..dcb52c423151 100644
--- a/drivers/firmware/Makefile
+++ b/drivers/firmware/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_QCOM_SCM) += qcom_scm.o
obj-$(CONFIG_QCOM_SCM_64) += qcom_scm-64.o
obj-$(CONFIG_QCOM_SCM_32) += qcom_scm-32.o
CFLAGS_qcom_scm-32.o :=$(call as-instr,.arch armv7-a\n.arch_extension sec,-DREQUIRES_SEC=1) -march=armv7-a
+obj-$(CONFIG_TI_SCI_PROTOCOL) += ti_sci.o
obj-y += broadcom/
obj-y += meson/
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
new file mode 100644
index 000000000000..5e99d7c18276
--- /dev/null
+++ b/drivers/firmware/ti_sci.c
@@ -0,0 +1,790 @@
+/*
+ * Texas Instruments System Control Interface Protocol Driver
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Nishanth Menon
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/bitmap.h>
+#include <linux/debugfs.h>
+#include <linux/export.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_client.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/semaphore.h>
+#include <linux/slab.h>
+#include <linux/soc/ti/ti-msgmgr.h>
+#include <linux/soc/ti/ti_sci_protocol.h>
+
+#include "ti_sci.h"
+
+/* List of all TI SCI devices active in system */
+static LIST_HEAD(ti_sci_list);
+/* Protection for the entire list */
+static DEFINE_MUTEX(ti_sci_list_mutex);
+
+/**
+ * struct ti_sci_xfer - Structure representing a message flow
+ * @tx_message: Transmit message
+ * @rx_len: Receive message length
+ * @xfer_buf: Preallocated buffer to store receive message
+ * Since we work with request-ACK protocol, we can
+ * reuse the same buffer for the rx path as we
+ * use for the tx path.
+ * @done: completion event
+ */
+struct ti_sci_xfer {
+ struct ti_msgmgr_message tx_message;
+ u8 rx_len;
+ u8 *xfer_buf;
+ struct completion done;
+};
+
+/**
+ * struct ti_sci_xfers_info - Structure to manage transfer information
+ * @sem_xfer_count: Counting Semaphore for managing max simultaneous
+ * Messages.
+ * @xfer_block: Preallocated Message array
+ * @xfer_alloc_table: Bitmap table for allocated messages.
+ * Index of this bitmap table is also used for message
+ * sequence identifier.
+ * @xfer_lock: Protection for message allocation
+ */
+struct ti_sci_xfers_info {
+ struct semaphore sem_xfer_count;
+ struct ti_sci_xfer *xfer_block;
+ unsigned long *xfer_alloc_table;
+ /* protect transfer allocation */
+ spinlock_t xfer_lock;
+};
+
+/**
+ * struct ti_sci_desc - Description of SoC integration
+ * @host_id: Host identifier representing the compute entity
+ * @max_rx_timeout_ms: Timeout for communication with SoC (in Milliseconds)
+ * @max_msgs: Maximum number of messages that can be pending
+ * simultaneously in the system
+ * @max_msg_size: Maximum size of data per message that can be handled.
+ */
+struct ti_sci_desc {
+ u8 host_id;
+ int max_rx_timeout_ms;
+ int max_msgs;
+ int max_msg_size;
+};
+
+/**
+ * struct ti_sci_info - Structure representing a TI SCI instance
+ * @dev: Device pointer
+ * @desc: SoC description for this instance
+ * @d: Debugfs file entry
+ * @debug_region: Memory region where the debug message are available
+ * @debug_region_size: Debug region size
+ * @debug_buffer: Buffer allocated to copy debug messages.
+ * @handle: Instance of TI SCI handle to send to clients.
+ * @cl: Mailbox Client
+ * @chan_tx: Transmit mailbox channel
+ * @chan_rx: Receive mailbox channel
+ * @minfo: Message info
+ * @node: list head
+ * @users: Number of users of this instance
+ */
+struct ti_sci_info {
+ struct device *dev;
+ const struct ti_sci_desc *desc;
+ struct dentry *d;
+ void __iomem *debug_region;
+ char *debug_buffer;
+ size_t debug_region_size;
+ struct ti_sci_handle handle;
+ struct mbox_client cl;
+ struct mbox_chan *chan_tx;
+ struct mbox_chan *chan_rx;
+ struct ti_sci_xfers_info minfo;
+ struct list_head node;
+ /* protected by ti_sci_list_mutex */
+ int users;
+};
+
+#define cl_to_ti_sci_info(c) container_of(c, struct ti_sci_info, cl)
+#define handle_to_ti_sci_info(h) container_of(h, struct ti_sci_info, handle)
+
+#ifdef CONFIG_DEBUG_FS
+
+/**
+ * ti_sci_debug_show() - Helper to dump the debug log
+ * @s: sequence file pointer
+ * @unused: unused.
+ *
+ * Return: 0
+ */
+static int ti_sci_debug_show(struct seq_file *s, void *unused)
+{
+ struct ti_sci_info *info = s->private;
+
+ memcpy_fromio(info->debug_buffer, info->debug_region,
+ info->debug_region_size);
+ /*
+ * We don't trust firmware to leave NULL terminated last byte (hence
+ * we have allocated 1 extra 0 byte). Since we cannot guarantee any
+ * specific data format for debug messages, We just present the data
+ * in the buffer as is - we expect the messages to be self explanatory.
+ */
+ seq_puts(s, info->debug_buffer);
+ return 0;
+}
+
+/**
+ * ti_sci_debug_open() - debug file open
+ * @inode: inode pointer
+ * @file: file pointer
+ *
+ * Return: result of single_open
+ */
+static int ti_sci_debug_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, ti_sci_debug_show, inode->i_private);
+}
+
+/* log file operations */
+static const struct file_operations ti_sci_debug_fops = {
+ .open = ti_sci_debug_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+/**
+ * ti_sci_debugfs_create() - Create log debug file
+ * @pdev: platform device pointer
+ * @info: Pointer to SCI entity information
+ *
+ * Return: 0 if all went fine, else corresponding error.
+ */
+static int ti_sci_debugfs_create(struct platform_device *pdev,
+ struct ti_sci_info *info)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ char debug_name[50] = "ti_sci_debug@";
+
+ /* Debug region is optional */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "debug_messages");
+ info->debug_region = devm_ioremap_resource(dev, res);
+ if (IS_ERR(info->debug_region))
+ return 0;
+ info->debug_region_size = resource_size(res);
+
+ info->debug_buffer = devm_kcalloc(dev, info->debug_region_size + 1,
+ sizeof(char), GFP_KERNEL);
+ if (!info->debug_buffer)
+ return -ENOMEM;
+ /* Setup NULL termination */
+ info->debug_buffer[info->debug_region_size] = 0;
+
+ info->d = debugfs_create_file(strncat(debug_name, dev_name(dev),
+ sizeof(debug_name)),
+ 0444, NULL, info, &ti_sci_debug_fops);
+ if (IS_ERR(info->d))
+ return PTR_ERR(info->d);
+
+ dev_dbg(dev, "Debug region => %p, size = %zu bytes, resource: %pr\n",
+ info->debug_region, info->debug_region_size, res);
+ return 0;
+}
+
+/**
+ * ti_sci_debugfs_destroy() - clean up log debug file
+ * @pdev: platform device pointer
+ * @info: Pointer to SCI entity information
+ */
+static void ti_sci_debugfs_destroy(struct platform_device *pdev,
+ struct ti_sci_info *info)
+{
+ if (IS_ERR(info->debug_region))
+ return;
+
+ debugfs_remove(info->d);
+}
+#else /* CONFIG_DEBUG_FS */
+static inline int ti_sci_debugfs_create(struct platform_device *dev,
+ struct ti_sci_info *info)
+{
+ return 0;
+}
+
+static inline void ti_sci_debugfs_destroy(struct platform_device *dev,
+ struct ti_sci_info *info)
+{
+}
+#endif /* CONFIG_DEBUG_FS */
+
+/**
+ * ti_sci_dump_header_dbg() - Helper to dump a message header.
+ * @dev: Device pointer corresponding to the SCI entity
+ * @hdr: pointer to header.
+ */
+static inline void ti_sci_dump_header_dbg(struct device *dev,
+ struct ti_sci_msg_hdr *hdr)
+{
+ dev_dbg(dev, "MSGHDR:type=0x%04x host=0x%02x seq=0x%02x flags=0x%08x\n",
+ hdr->type, hdr->host, hdr->seq, hdr->flags);
+}
+
+/**
+ * ti_sci_rx_callback() - mailbox client callback for receive messages
+ * @cl: client pointer
+ * @m: mailbox message
+ *
+ * Processes one received message to appropriate transfer information and
+ * signals completion of the transfer.
+ *
+ * NOTE: This function will be invoked in IRQ context, hence should be
+ * as optimal as possible.
+ */
+static void ti_sci_rx_callback(struct mbox_client *cl, void *m)
+{
+ struct ti_sci_info *info = cl_to_ti_sci_info(cl);
+ struct device *dev = info->dev;
+ struct ti_sci_xfers_info *minfo = &info->minfo;
+ struct ti_msgmgr_message *mbox_msg = m;
+ struct ti_sci_msg_hdr *hdr = (struct ti_sci_msg_hdr *)mbox_msg->buf;
+ struct ti_sci_xfer *xfer;
+ u8 xfer_id;
+
+ xfer_id = hdr->seq;
+
+ /*
+ * Are we even expecting this?
+ * NOTE: barriers were implicit in locks used for modifying the bitmap
+ */
+ if (!test_bit(xfer_id, minfo->xfer_alloc_table)) {
+ dev_err(dev, "Message for %d is not expected!\n", xfer_id);
+ return;
+ }
+
+ xfer = &minfo->xfer_block[xfer_id];
+
+ /* Is the message of valid length? */
+ if (mbox_msg->len > info->desc->max_msg_size) {
+ dev_err(dev, "Unable to handle %d xfer(max %d)\n",
+ mbox_msg->len, info->desc->max_msg_size);
+ ti_sci_dump_header_dbg(dev, hdr);
+ return;
+ }
+ if (mbox_msg->len < xfer->rx_len) {
+ dev_err(dev, "Recv xfer %d < expected %d length\n",
+ mbox_msg->len, xfer->rx_len);
+ ti_sci_dump_header_dbg(dev, hdr);
+ return;
+ }
+
+ ti_sci_dump_header_dbg(dev, hdr);
+ /* Take a copy to the rx buffer.. */
+ memcpy(xfer->xfer_buf, mbox_msg->buf, xfer->rx_len);
+ complete(&xfer->done);
+}
+
+/**
+ * ti_sci_get_one_xfer() - Allocate one message
+ * @info: Pointer to SCI entity information
+ * @msg_type: Message type
+ * @msg_flags: Flag to set for the message
+ * @tx_message_size: transmit message size
+ * @rx_message_size: receive message size
+ *
+ * Helper function which is used by various command functions that are
+ * exposed to clients of this driver for allocating a message traffic event.
+ *
+ * This function can sleep depending on pending requests already in the system
+ * for the SCI entity. Further, this also holds a spinlock to maintain integrity
+ * of internal data structures.
+ *
+ * Return: 0 if all went fine, else corresponding error.
+ */
+static struct ti_sci_xfer *ti_sci_get_one_xfer(struct ti_sci_info *info,
+ u16 msg_type, u32 msg_flags,
+ size_t tx_message_size,
+ size_t rx_message_size)
+{
+ struct ti_sci_xfers_info *minfo = &info->minfo;
+ struct ti_sci_xfer *xfer;
+ struct ti_sci_msg_hdr *hdr;
+ unsigned long flags;
+ unsigned long bit_pos;
+ u8 xfer_id;
+ int ret;
+ int timeout;
+
+ /* Ensure we have sane transfer sizes */
+ if (rx_message_size > info->desc->max_msg_size ||
+ tx_message_size > info->desc->max_msg_size ||
+ rx_message_size < sizeof(*hdr) || tx_message_size < sizeof(*hdr))
+ return ERR_PTR(-ERANGE);
+
+ /*
+ * Ensure we have only controlled number of pending messages.
+ * Ideally, we might just have to wait a single message, be
+ * conservative and wait 5 times that..
+ */
+ timeout = msecs_to_jiffies(info->desc->max_rx_timeout_ms) * 5;
+ ret = down_timeout(&minfo->sem_xfer_count, timeout);
+ if (ret < 0)
+ return ERR_PTR(ret);
+
+ /* Keep the locked section as small as possible */
+ spin_lock_irqsave(&minfo->xfer_lock, flags);
+ bit_pos = find_first_zero_bit(minfo->xfer_alloc_table,
+ info->desc->max_msgs);
+ set_bit(bit_pos, minfo->xfer_alloc_table);
+ spin_unlock_irqrestore(&minfo->xfer_lock, flags);
+
+ /*
+ * We already ensured in probe that we can have max messages that can
+ * fit in hdr.seq - NOTE: this improves access latencies
+ * to predictable O(1) access, BUT, it opens us to risk if
+ * remote misbehaves with corrupted message sequence responses.
+ * If that happens, we are going to be messed up anyways..
+ */
+ xfer_id = (u8)bit_pos;
+
+ xfer = &minfo->xfer_block[xfer_id];
+
+ hdr = (struct ti_sci_msg_hdr *)xfer->tx_message.buf;
+ xfer->tx_message.len = tx_message_size;
+ xfer->rx_len = (u8)rx_message_size;
+
+ reinit_completion(&xfer->done);
+
+ hdr->seq = xfer_id;
+ hdr->type = msg_type;
+ hdr->host = info->desc->host_id;
+ hdr->flags = msg_flags;
+
+ return xfer;
+}
+
+/**
+ * ti_sci_put_one_xfer() - Release a message
+ * @minfo: transfer info pointer
+ * @xfer: message that was reserved by ti_sci_get_one_xfer
+ *
+ * This holds a spinlock to maintain integrity of internal data structures.
+ */
+static void ti_sci_put_one_xfer(struct ti_sci_xfers_info *minfo,
+ struct ti_sci_xfer *xfer)
+{
+ unsigned long flags;
+ struct ti_sci_msg_hdr *hdr;
+ u8 xfer_id;
+
+ hdr = (struct ti_sci_msg_hdr *)xfer->tx_message.buf;
+ xfer_id = hdr->seq;
+
+ /*
+ * Keep the locked section as small as possible
+ * NOTE: we might escape with smp_mb and no lock here..
+ * but just be conservative and symmetric.
+ */
+ spin_lock_irqsave(&minfo->xfer_lock, flags);
+ clear_bit(xfer_id, minfo->xfer_alloc_table);
+ spin_unlock_irqrestore(&minfo->xfer_lock, flags);
+
+ /* Increment the count for the next user to get through */
+ up(&minfo->sem_xfer_count);
+}
+
+/**
+ * ti_sci_do_xfer() - Do one transfer
+ * @info: Pointer to SCI entity information
+ * @xfer: Transfer to initiate and wait for response
+ *
+ * Return: -ETIMEDOUT in case of no response, if transmit error,
+ * return corresponding error, else if all goes well,
+ * return 0.
+ */
+static inline int ti_sci_do_xfer(struct ti_sci_info *info,
+ struct ti_sci_xfer *xfer)
+{
+ int ret;
+ int timeout;
+ struct device *dev = info->dev;
+
+ ret = mbox_send_message(info->chan_tx, &xfer->tx_message);
+ if (ret < 0)
+ return ret;
+
+ ret = 0;
+
+ /* And we wait for the response. */
+ timeout = msecs_to_jiffies(info->desc->max_rx_timeout_ms);
+ if (!wait_for_completion_timeout(&xfer->done, timeout)) {
+ dev_err(dev, "Mbox timedout in resp(caller: %pF)\n",
+ (void *)_RET_IP_);
+ ret = -ETIMEDOUT;
+ }
+ /*
+ * NOTE: we might prefer not to need the mailbox ticker to manage the
+ * transfer queueing since the protocol layer queues things by itself.
+ * Unfortunately, we have to kick the mailbox framework after we have
+ * received our message.
+ */
+ mbox_client_txdone(info->chan_tx, ret);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_revision() - command to get the revision of the SCI entity
+ * @info: Pointer to SCI entity information
+ *
+ * Updates the SCI information in the internal data structure.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_get_revision(struct ti_sci_info *info)
+{
+ struct device *dev = info->dev;
+ struct ti_sci_handle *handle = &info->handle;
+ struct ti_sci_version_info *ver = &handle->version;
+ struct ti_sci_msg_resp_version *rev_info;
+ struct ti_sci_xfer *xfer;
+ int ret;
+
+ /* No need to setup flags since it is expected to respond */
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_VERSION,
+ 0x0, sizeof(struct ti_sci_msg_hdr),
+ sizeof(*rev_info));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+
+ rev_info = (struct ti_sci_msg_resp_version *)xfer->xfer_buf;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ ver->abi_major = rev_info->abi_major;
+ ver->abi_minor = rev_info->abi_minor;
+ ver->firmware_revision = rev_info->firmware_revision;
+ strncpy(ver->firmware_description, rev_info->firmware_description,
+ sizeof(ver->firmware_description));
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+ return ret;
+}
+
+/**
+ * ti_sci_get_handle() - Get the TI SCI handle for a device
+ * @dev: Pointer to device for which we want SCI handle
+ *
+ * NOTE: The function does not track individual clients of the framework
+ * and is expected to be maintained by caller of TI SCI protocol library.
+ * ti_sci_put_handle must be balanced with successful ti_sci_get_handle
+ * Return: pointer to handle if successful, else:
+ * -EPROBE_DEFER if the instance is not ready
+ * -ENODEV if the required node handler is missing
+ * -EINVAL if invalid conditions are encountered.
+ */
+const struct ti_sci_handle *ti_sci_get_handle(struct device *dev)
+{
+ struct device_node *ti_sci_np;
+ struct list_head *p;
+ struct ti_sci_handle *handle = NULL;
+ struct ti_sci_info *info;
+
+ if (!dev) {
+ pr_err("I need a device pointer\n");
+ return ERR_PTR(-EINVAL);
+ }
+ ti_sci_np = of_get_parent(dev->of_node);
+ if (!ti_sci_np) {
+ dev_err(dev, "No OF information\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ mutex_lock(&ti_sci_list_mutex);
+ list_for_each(p, &ti_sci_list) {
+ info = list_entry(p, struct ti_sci_info, node);
+ if (ti_sci_np == info->dev->of_node) {
+ handle = &info->handle;
+ info->users++;
+ break;
+ }
+ }
+ mutex_unlock(&ti_sci_list_mutex);
+ of_node_put(ti_sci_np);
+
+ if (!handle)
+ return ERR_PTR(-EPROBE_DEFER);
+
+ return handle;
+}
+EXPORT_SYMBOL_GPL(ti_sci_get_handle);
+
+/**
+ * ti_sci_put_handle() - Release the handle acquired by ti_sci_get_handle
+ * @handle: Handle acquired by ti_sci_get_handle
+ *
+ * NOTE: The function does not track individual clients of the framework
+ * and is expected to be maintained by caller of TI SCI protocol library.
+ * ti_sci_put_handle must be balanced with successful ti_sci_get_handle
+ *
+ * Return: 0 is successfully released
+ * if an error pointer was passed, it returns the error value back,
+ * if null was passed, it returns -EINVAL;
+ */
+int ti_sci_put_handle(const struct ti_sci_handle *handle)
+{
+ struct ti_sci_info *info;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ mutex_lock(&ti_sci_list_mutex);
+ if (!WARN_ON(!info->users))
+ info->users--;
+ mutex_unlock(&ti_sci_list_mutex);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ti_sci_put_handle);
+
+static void devm_ti_sci_release(struct device *dev, void *res)
+{
+ const struct ti_sci_handle **ptr = res;
+ const struct ti_sci_handle *handle = *ptr;
+ int ret;
+
+ ret = ti_sci_put_handle(handle);
+ if (ret)
+ dev_err(dev, "failed to put handle %d\n", ret);
+}
+
+/**
+ * devm_ti_sci_get_handle() - Managed get handle
+ * @dev: device for which we want SCI handle for.
+ *
+ * NOTE: This releases the handle once the device resources are
+ * no longer needed. MUST NOT BE released with ti_sci_put_handle.
+ * The function does not track individual clients of the framework
+ * and is expected to be maintained by caller of TI SCI protocol library.
+ *
+ * Return: 0 if all went fine, else corresponding error.
+ */
+const struct ti_sci_handle *devm_ti_sci_get_handle(struct device *dev)
+{
+ const struct ti_sci_handle **ptr;
+ const struct ti_sci_handle *handle;
+
+ ptr = devres_alloc(devm_ti_sci_release, sizeof(*ptr), GFP_KERNEL);
+ if (!ptr)
+ return ERR_PTR(-ENOMEM);
+ handle = ti_sci_get_handle(dev);
+
+ if (!IS_ERR(handle)) {
+ *ptr = handle;
+ devres_add(dev, ptr);
+ } else {
+ devres_free(ptr);
+ }
+
+ return handle;
+}
+EXPORT_SYMBOL_GPL(devm_ti_sci_get_handle);
+
+/* Description for K2G */
+static const struct ti_sci_desc ti_sci_pmmc_k2g_desc = {
+ .host_id = 2,
+ /* Conservative duration */
+ .max_rx_timeout_ms = 1000,
+ /* Limited by MBOX_TX_QUEUE_LEN. K2G can handle upto 128 messages! */
+ .max_msgs = 20,
+ .max_msg_size = 64,
+};
+
+static const struct of_device_id ti_sci_of_match[] = {
+ {.compatible = "ti,k2g-sci", .data = &ti_sci_pmmc_k2g_desc},
+ { /* Sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ti_sci_of_match);
+
+static int ti_sci_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct of_device_id *of_id;
+ const struct ti_sci_desc *desc;
+ struct ti_sci_xfer *xfer;
+ struct ti_sci_info *info = NULL;
+ struct ti_sci_xfers_info *minfo;
+ struct mbox_client *cl;
+ int ret = -EINVAL;
+ int i;
+
+ of_id = of_match_device(ti_sci_of_match, dev);
+ if (!of_id) {
+ dev_err(dev, "OF data missing\n");
+ return -EINVAL;
+ }
+ desc = of_id->data;
+
+ info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ info->dev = dev;
+ info->desc = desc;
+ INIT_LIST_HEAD(&info->node);
+ minfo = &info->minfo;
+
+ /*
+ * Pre-allocate messages
+ * NEVER allocate more than what we can indicate in hdr.seq
+ * if we have data description bug, force a fix..
+ */
+ if (WARN_ON(desc->max_msgs >=
+ 1 << 8 * sizeof(((struct ti_sci_msg_hdr *)0)->seq)))
+ return -EINVAL;
+
+ minfo->xfer_block = devm_kcalloc(dev,
+ desc->max_msgs,
+ sizeof(*minfo->xfer_block),
+ GFP_KERNEL);
+ if (!minfo->xfer_block)
+ return -ENOMEM;
+
+ minfo->xfer_alloc_table = devm_kzalloc(dev,
+ BITS_TO_LONGS(desc->max_msgs)
+ * sizeof(unsigned long),
+ GFP_KERNEL);
+ if (!minfo->xfer_alloc_table)
+ return -ENOMEM;
+ bitmap_zero(minfo->xfer_alloc_table, desc->max_msgs);
+
+ /* Pre-initialize the buffer pointer to pre-allocated buffers */
+ for (i = 0, xfer = minfo->xfer_block; i < desc->max_msgs; i++, xfer++) {
+ xfer->xfer_buf = devm_kcalloc(dev, 1, desc->max_msg_size,
+ GFP_KERNEL);
+ if (!xfer->xfer_buf)
+ return -ENOMEM;
+
+ xfer->tx_message.buf = xfer->xfer_buf;
+ init_completion(&xfer->done);
+ }
+
+ ret = ti_sci_debugfs_create(pdev, info);
+ if (ret)
+ dev_warn(dev, "Failed to create debug file\n");
+
+ platform_set_drvdata(pdev, info);
+
+ cl = &info->cl;
+ cl->dev = dev;
+ cl->tx_block = false;
+ cl->rx_callback = ti_sci_rx_callback;
+ cl->knows_txdone = true;
+
+ spin_lock_init(&minfo->xfer_lock);
+ sema_init(&minfo->sem_xfer_count, desc->max_msgs);
+
+ info->chan_rx = mbox_request_channel_byname(cl, "rx");
+ if (IS_ERR(info->chan_rx)) {
+ ret = PTR_ERR(info->chan_rx);
+ goto out;
+ }
+
+ info->chan_tx = mbox_request_channel_byname(cl, "tx");
+ if (IS_ERR(info->chan_tx)) {
+ ret = PTR_ERR(info->chan_tx);
+ goto out;
+ }
+ ret = ti_sci_cmd_get_revision(info);
+ if (ret) {
+ dev_err(dev, "Unable to communicate with TISCI(%d)\n", ret);
+ goto out;
+ }
+
+ dev_info(dev, "ABI: %d.%d (firmware rev 0x%04x '%s')\n",
+ info->handle.version.abi_major, info->handle.version.abi_minor,
+ info->handle.version.firmware_revision,
+ info->handle.version.firmware_description);
+
+ mutex_lock(&ti_sci_list_mutex);
+ list_add_tail(&info->node, &ti_sci_list);
+ mutex_unlock(&ti_sci_list_mutex);
+
+ return of_platform_populate(dev->of_node, NULL, NULL, dev);
+out:
+ if (!IS_ERR(info->chan_tx))
+ mbox_free_channel(info->chan_tx);
+ if (!IS_ERR(info->chan_rx))
+ mbox_free_channel(info->chan_rx);
+ debugfs_remove(info->d);
+ return ret;
+}
+
+static int ti_sci_remove(struct platform_device *pdev)
+{
+ struct ti_sci_info *info;
+ struct device *dev = &pdev->dev;
+ int ret = 0;
+
+ of_platform_depopulate(dev);
+
+ info = platform_get_drvdata(pdev);
+
+ mutex_lock(&ti_sci_list_mutex);
+ if (info->users)
+ ret = -EBUSY;
+ else
+ list_del(&info->node);
+ mutex_unlock(&ti_sci_list_mutex);
+
+ if (!ret) {
+ ti_sci_debugfs_destroy(pdev, info);
+
+ /* Safe to free channels since no more users */
+ mbox_free_channel(info->chan_tx);
+ mbox_free_channel(info->chan_rx);
+ }
+
+ return ret;
+}
+
+static struct platform_driver ti_sci_driver = {
+ .probe = ti_sci_probe,
+ .remove = ti_sci_remove,
+ .driver = {
+ .name = "ti-sci",
+ .of_match_table = of_match_ptr(ti_sci_of_match),
+ },
+};
+module_platform_driver(ti_sci_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI System Control Interface(SCI) driver");
+MODULE_AUTHOR("Nishanth Menon");
+MODULE_ALIAS("platform:ti-sci");
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
new file mode 100644
index 000000000000..e9dc53f26e0e
--- /dev/null
+++ b/drivers/firmware/ti_sci.h
@@ -0,0 +1,93 @@
+/*
+ * Texas Instruments System Control Interface (TISCI) Protocol
+ *
+ * Communication protocol with TI SCI hardware
+ * The system works in a message response protocol
+ * See: http://processors.wiki.ti.com/index.php/TISCI for details
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ *
+ * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the
+ * distribution.
+ *
+ * Neither the name of Texas Instruments Incorporated nor the names of
+ * its contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ */
+
+#ifndef __TI_SCI_H
+#define __TI_SCI_H
+
+/* Generic Messages */
+#define TI_SCI_MSG_ENABLE_WDT 0x0000
+#define TI_SCI_MSG_WAKE_RESET 0x0001
+#define TI_SCI_MSG_VERSION 0x0002
+#define TI_SCI_MSG_WAKE_REASON 0x0003
+#define TI_SCI_MSG_GOODBYE 0x0004
+
+/**
+ * struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
+ * @type: Type of messages: One of TI_SCI_MSG* values
+ * @host: Host of the message
+ * @seq: Message identifier indicating a transfer sequence
+ * @flags: Flag for the message
+ */
+struct ti_sci_msg_hdr {
+ u16 type;
+ u8 host;
+ u8 seq;
+#define TI_SCI_MSG_FLAG(val) (1 << (val))
+#define TI_SCI_FLAG_REQ_GENERIC_NORESPONSE 0x0
+#define TI_SCI_FLAG_REQ_ACK_ON_RECEIVED TI_SCI_MSG_FLAG(0)
+#define TI_SCI_FLAG_REQ_ACK_ON_PROCESSED TI_SCI_MSG_FLAG(1)
+#define TI_SCI_FLAG_RESP_GENERIC_NACK 0x0
+#define TI_SCI_FLAG_RESP_GENERIC_ACK TI_SCI_MSG_FLAG(1)
+ /* Additional Flags */
+ u32 flags;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_version - Response for a message
+ * @hdr: Generic header
+ * @firmware_description: String describing the firmware
+ * @firmware_revision: Firmware revision
+ * @abi_major: Major version of the ABI that firmware supports
+ * @abi_minor: Minor version of the ABI that firmware supports
+ *
+ * In general, ABI version changes follow the rule that minor version increments
+ * are backward compatible. Major revision changes in ABI may not be
+ * backward compatible.
+ *
+ * Response to a generic message with message type TI_SCI_MSG_VERSION
+ */
+struct ti_sci_msg_resp_version {
+ struct ti_sci_msg_hdr hdr;
+ char firmware_description[32];
+ u16 firmware_revision;
+ u8 abi_major;
+ u8 abi_minor;
+} __packed;
+
+#endif /* __TI_SCI_H */
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
new file mode 100644
index 000000000000..e73483fd5327
--- /dev/null
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -0,0 +1,69 @@
+/*
+ * Texas Instruments System Control Interface Protocol
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ * Nishanth Menon
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __TISCI_PROTOCOL_H
+#define __TISCI_PROTOCOL_H
+
+/**
+ * struct ti_sci_version_info - version information structure
+ * @abi_major: Major ABI version. Change here implies risk of backward
+ * compatibility break.
+ * @abi_minor: Minor ABI version. Change here implies new feature addition,
+ * or compatible change in ABI.
+ * @firmware_revision: Firmware revision (not usually used).
+ * @firmware_description: Firmware description (not usually used).
+ */
+struct ti_sci_version_info {
+ u8 abi_major;
+ u8 abi_minor;
+ u16 firmware_revision;
+ char firmware_description[32];
+};
+
+/**
+ * struct ti_sci_handle - Handle returned to TI SCI clients for usage.
+ * @version: structure containing version information
+ */
+struct ti_sci_handle {
+ struct ti_sci_version_info version;
+};
+
+#if IS_ENABLED(CONFIG_TI_SCI_PROTOCOL)
+const struct ti_sci_handle *ti_sci_get_handle(struct device *dev);
+int ti_sci_put_handle(const struct ti_sci_handle *handle);
+const struct ti_sci_handle *devm_ti_sci_get_handle(struct device *dev);
+
+#else /* CONFIG_TI_SCI_PROTOCOL */
+
+static inline const struct ti_sci_handle *ti_sci_get_handle(struct device *dev)
+{
+ return ERR_PTR(-EINVAL);
+}
+
+static inline int ti_sci_put_handle(const struct ti_sci_handle *handle)
+{
+ return -EINVAL;
+}
+
+static inline
+const struct ti_sci_handle *devm_ti_sci_get_handle(struct device *dev)
+{
+ return ERR_PTR(-EINVAL);
+}
+
+#endif /* CONFIG_TI_SCI_PROTOCOL */
+
+#endif /* __TISCI_PROTOCOL_H */
--
2.10.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH V4 3/5] firmware: ti_sci: Add support for Device control
2016-10-18 23:08 [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 1/5] Documentation: Add support for TI System Control Interface (TI-SCI) protocol Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 2/5] firmware: Add basic " Nishanth Menon
@ 2016-10-18 23:08 ` Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 4/5] firmware: ti_sci: Add support for Clock control Nishanth Menon
` (2 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: Tero Kristo, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman, Nishanth Menon
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.
TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
We introduce the fundamental device management capability support to
the driver protocol as part of this change.
[d-gerlach@ti.com: Contributed device reset handling]
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since v3: none
V3: https://patchwork.kernel.org/patch/9317843/
drivers/firmware/ti_sci.c | 433 +++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 98 ++++++++
include/linux/soc/ti/ti_sci_protocol.h | 91 +++++++
3 files changed, 622 insertions(+)
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 5e99d7c18276..c7b25ccf6f07 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -495,6 +495,437 @@ static int ti_sci_cmd_get_revision(struct ti_sci_info *info)
}
/**
+ * ti_sci_is_response_ack() - Generic ACK/NACK message checkup
+ * @r: pointer to response buffer
+ *
+ * Return: true if the response was an ACK, else returns false.
+ */
+static inline bool ti_sci_is_response_ack(void *r)
+{
+ struct ti_sci_msg_hdr *hdr = r;
+
+ return hdr->flags & TI_SCI_FLAG_RESP_GENERIC_ACK ? true : false;
+}
+
+/**
+ * ti_sci_set_device_state() - Set device state helper
+ * @handle: pointer to TI SCI handle
+ * @id: Device identifier
+ * @flags: flags to setup for the device
+ * @state: State to move the device to
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_set_device_state(const struct ti_sci_handle *handle,
+ u32 id, u32 flags, u8 state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_device_state *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_DEVICE_STATE,
+ flags | TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_device_state *)xfer->xfer_buf;
+ req->id = id;
+ req->state = state;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_get_device_state() - Get device state helper
+ * @handle: Handle to the device
+ * @id: Device Identifier
+ * @clcnt: Pointer to Context Loss Count
+ * @resets: pointer to resets
+ * @p_state: pointer to p_state
+ * @c_state: pointer to c_state
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_get_device_state(const struct ti_sci_handle *handle,
+ u32 id, u32 *clcnt, u32 *resets,
+ u8 *p_state, u8 *c_state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_device_state *req;
+ struct ti_sci_msg_resp_get_device_state *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ if (!clcnt && !resets && !p_state && !c_state)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ /* Response is expected, so need of any flags */
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_DEVICE_STATE,
+ 0, sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_device_state *)xfer->xfer_buf;
+ req->id = id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_device_state *)xfer->xfer_buf;
+ if (!ti_sci_is_response_ack(resp)) {
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ if (clcnt)
+ *clcnt = resp->context_loss_count;
+ if (resets)
+ *resets = resp->resets;
+ if (p_state)
+ *p_state = resp->programmed_state;
+ if (c_state)
+ *c_state = resp->current_state;
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_device() - command to request for device managed by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ *
+ * NOTE: The request is for exclusive access for the processor.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_get_device(const struct ti_sci_handle *handle, u32 id)
+{
+ return ti_sci_set_device_state(handle, id,
+ MSG_FLAG_DEVICE_EXCLUSIVE,
+ MSG_DEVICE_SW_STATE_ON);
+}
+
+/**
+ * ti_sci_cmd_idle_device() - Command to idle a device managed by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_idle_device(const struct ti_sci_handle *handle, u32 id)
+{
+ return ti_sci_set_device_state(handle, id,
+ MSG_FLAG_DEVICE_EXCLUSIVE,
+ MSG_DEVICE_SW_STATE_RETENTION);
+}
+
+/**
+ * ti_sci_cmd_put_device() - command to release a device managed by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_put_device(const struct ti_sci_handle *handle, u32 id)
+{
+ return ti_sci_set_device_state(handle, id,
+ 0, MSG_DEVICE_SW_STATE_AUTO_OFF);
+}
+
+/**
+ * ti_sci_cmd_dev_is_valid() - Is the device valid
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Return: 0 if all went fine and the device ID is valid, else return
+ * appropriate error.
+ */
+static int ti_sci_cmd_dev_is_valid(const struct ti_sci_handle *handle, u32 id)
+{
+ u8 unused;
+
+ /* check the device state which will also tell us if the ID is valid */
+ return ti_sci_get_device_state(handle, id, NULL, NULL, NULL, &unused);
+}
+
+/**
+ * ti_sci_cmd_dev_get_clcnt() - Get context loss counter
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @count: Pointer to Context Loss counter to populate
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_get_clcnt(const struct ti_sci_handle *handle, u32 id,
+ u32 *count)
+{
+ return ti_sci_get_device_state(handle, id, count, NULL, NULL, NULL);
+}
+
+/**
+ * ti_sci_cmd_dev_is_idle() - Check if the device is requested to be idle
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @r_state: true if requested to be idle
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_idle(const struct ti_sci_handle *handle, u32 id,
+ bool *r_state)
+{
+ int ret;
+ u8 state;
+
+ if (!r_state)
+ return -EINVAL;
+
+ ret = ti_sci_get_device_state(handle, id, NULL, NULL, &state, NULL);
+ if (ret)
+ return ret;
+
+ *r_state = (state == MSG_DEVICE_SW_STATE_RETENTION);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_dev_is_stop() - Check if the device is requested to be stopped
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @r_state: true if requested to be stopped
+ * @curr_state: true if currently stopped.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_stop(const struct ti_sci_handle *handle, u32 id,
+ bool *r_state, bool *curr_state)
+{
+ int ret;
+ u8 p_state, c_state;
+
+ if (!r_state && !curr_state)
+ return -EINVAL;
+
+ ret =
+ ti_sci_get_device_state(handle, id, NULL, NULL, &p_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (r_state)
+ *r_state = (p_state == MSG_DEVICE_SW_STATE_AUTO_OFF);
+ if (curr_state)
+ *curr_state = (c_state == MSG_DEVICE_HW_STATE_OFF);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_dev_is_on() - Check if the device is requested to be ON
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @r_state: true if requested to be ON
+ * @curr_state: true if currently ON and active
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_on(const struct ti_sci_handle *handle, u32 id,
+ bool *r_state, bool *curr_state)
+{
+ int ret;
+ u8 p_state, c_state;
+
+ if (!r_state && !curr_state)
+ return -EINVAL;
+
+ ret =
+ ti_sci_get_device_state(handle, id, NULL, NULL, &p_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (r_state)
+ *r_state = (p_state == MSG_DEVICE_SW_STATE_ON);
+ if (curr_state)
+ *curr_state = (c_state == MSG_DEVICE_HW_STATE_ON);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_dev_is_trans() - Check if the device is currently transitioning
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @curr_state: true if currently transitioning.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_trans(const struct ti_sci_handle *handle, u32 id,
+ bool *curr_state)
+{
+ int ret;
+ u8 state;
+
+ if (!curr_state)
+ return -EINVAL;
+
+ ret = ti_sci_get_device_state(handle, id, NULL, NULL, NULL, &state);
+ if (ret)
+ return ret;
+
+ *curr_state = (state == MSG_DEVICE_HW_STATE_TRANS);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_set_device_resets() - command to set resets for device managed
+ * by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ * @reset_state: Device specific reset bit field
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_set_device_resets(const struct ti_sci_handle *handle,
+ u32 id, u32 reset_state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_device_resets *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_DEVICE_RESETS,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_device_resets *)xfer->xfer_buf;
+ req->id = id;
+ req->resets = reset_state;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_device_resets() - Get reset state for device managed
+ * by TISCI
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @reset_state: Pointer to reset state to populate
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_get_device_resets(const struct ti_sci_handle *handle,
+ u32 id, u32 *reset_state)
+{
+ return ti_sci_get_device_state(handle, id, NULL, reset_state, NULL,
+ NULL);
+}
+
+/*
+ * ti_sci_setup_ops() - Setup the operations structures
+ * @info: pointer to TISCI pointer
+ */
+static void ti_sci_setup_ops(struct ti_sci_info *info)
+{
+ struct ti_sci_ops *ops = &info->handle.ops;
+ struct ti_sci_dev_ops *dops = &ops->dev_ops;
+
+ dops->get_device = ti_sci_cmd_get_device;
+ dops->idle_device = ti_sci_cmd_idle_device;
+ dops->put_device = ti_sci_cmd_put_device;
+
+ dops->is_valid = ti_sci_cmd_dev_is_valid;
+ dops->get_context_loss_count = ti_sci_cmd_dev_get_clcnt;
+ dops->is_idle = ti_sci_cmd_dev_is_idle;
+ dops->is_stop = ti_sci_cmd_dev_is_stop;
+ dops->is_on = ti_sci_cmd_dev_is_on;
+ dops->is_transitioning = ti_sci_cmd_dev_is_trans;
+ dops->set_device_resets = ti_sci_cmd_set_device_resets;
+ dops->get_device_resets = ti_sci_cmd_get_device_resets;
+}
+
+/**
* ti_sci_get_handle() - Get the TI SCI handle for a device
* @dev: Pointer to device for which we want SCI handle
*
@@ -727,6 +1158,8 @@ static int ti_sci_probe(struct platform_device *pdev)
goto out;
}
+ ti_sci_setup_ops(info);
+
dev_info(dev, "ABI: %d.%d (firmware rev 0x%04x '%s')\n",
info->handle.version.abi_major, info->handle.version.abi_minor,
info->handle.version.firmware_revision,
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index e9dc53f26e0e..29ce0532a7ca 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -47,6 +47,11 @@
#define TI_SCI_MSG_WAKE_REASON 0x0003
#define TI_SCI_MSG_GOODBYE 0x0004
+/* Device requests */
+#define TI_SCI_MSG_SET_DEVICE_STATE 0x0200
+#define TI_SCI_MSG_GET_DEVICE_STATE 0x0201
+#define TI_SCI_MSG_SET_DEVICE_RESETS 0x0202
+
/**
* struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
* @type: Type of messages: One of TI_SCI_MSG* values
@@ -90,4 +95,97 @@ struct ti_sci_msg_resp_version {
u8 abi_minor;
} __packed;
+/**
+ * struct ti_sci_msg_req_set_device_state - Set the desired state of the device
+ * @hdr: Generic header
+ * @id: Indicates which device to modify
+ * @reserved: Reserved space in message, must be 0 for backward compatibility
+ * @state: The desired state of the device.
+ *
+ * Certain flags can also be set to alter the device state:
+ * + MSG_FLAG_DEVICE_WAKE_ENABLED - Configure the device to be a wake source.
+ * The meaning of this flag will vary slightly from device to device and from
+ * SoC to SoC but it generally allows the device to wake the SoC out of deep
+ * suspend states.
+ * + MSG_FLAG_DEVICE_RESET_ISO - Enable reset isolation for this device.
+ * + MSG_FLAG_DEVICE_EXCLUSIVE - Claim this device exclusively. When passed
+ * with STATE_RETENTION or STATE_ON, it will claim the device exclusively.
+ * If another host already has this device set to STATE_RETENTION or STATE_ON,
+ * the message will fail. Once successful, other hosts attempting to set
+ * STATE_RETENTION or STATE_ON will fail.
+ *
+ * Request type is TI_SCI_MSG_SET_DEVICE_STATE, responded with a generic
+ * ACK/NACK message.
+ */
+struct ti_sci_msg_req_set_device_state {
+ /* Additional hdr->flags options */
+#define MSG_FLAG_DEVICE_WAKE_ENABLED TI_SCI_MSG_FLAG(8)
+#define MSG_FLAG_DEVICE_RESET_ISO TI_SCI_MSG_FLAG(9)
+#define MSG_FLAG_DEVICE_EXCLUSIVE TI_SCI_MSG_FLAG(10)
+ struct ti_sci_msg_hdr hdr;
+ u32 id;
+ u32 reserved;
+
+#define MSG_DEVICE_SW_STATE_AUTO_OFF 0
+#define MSG_DEVICE_SW_STATE_RETENTION 1
+#define MSG_DEVICE_SW_STATE_ON 2
+ u8 state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_device_state - Request to get device.
+ * @hdr: Generic header
+ * @id: Device Identifier
+ *
+ * Request type is TI_SCI_MSG_GET_DEVICE_STATE, responded device state
+ * information
+ */
+struct ti_sci_msg_req_get_device_state {
+ struct ti_sci_msg_hdr hdr;
+ u32 id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_device_state - Response to get device request.
+ * @hdr: Generic header
+ * @context_loss_count: Indicates how many times the device has lost context. A
+ * driver can use this monotonic counter to determine if the device has
+ * lost context since the last time this message was exchanged.
+ * @resets: Programmed state of the reset lines.
+ * @programmed_state: The state as programmed by set_device.
+ * - Uses the MSG_DEVICE_SW_* macros
+ * @current_state: The actual state of the hardware.
+ *
+ * Response to request TI_SCI_MSG_GET_DEVICE_STATE.
+ */
+struct ti_sci_msg_resp_get_device_state {
+ struct ti_sci_msg_hdr hdr;
+ u32 context_loss_count;
+ u32 resets;
+ u8 programmed_state;
+#define MSG_DEVICE_HW_STATE_OFF 0
+#define MSG_DEVICE_HW_STATE_ON 1
+#define MSG_DEVICE_HW_STATE_TRANS 2
+ u8 current_state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_set_device_resets - Set the desired resets
+ * configuration of the device
+ * @hdr: Generic header
+ * @id: Indicates which device to modify
+ * @resets: A bit field of resets for the device. The meaning, behavior,
+ * and usage of the reset flags are device specific. 0 for a bit
+ * indicates releasing the reset represented by that bit while 1
+ * indicates keeping it held.
+ *
+ * Request type is TI_SCI_MSG_SET_DEVICE_RESETS, responded with a generic
+ * ACK/NACK message.
+ */
+struct ti_sci_msg_req_set_device_resets {
+ struct ti_sci_msg_hdr hdr;
+ u32 id;
+ u32 resets;
+} __packed;
+
#endif /* __TI_SCI_H */
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index e73483fd5327..87fa73851471 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -33,12 +33,103 @@ struct ti_sci_version_info {
char firmware_description[32];
};
+struct ti_sci_handle;
+
+/**
+ * struct ti_sci_dev_ops - Device control operations
+ * @get_device: Command to request for device managed by TISCI
+ * Returns 0 for successful exclusive request, else returns
+ * corresponding error message.
+ * @idle_device: Command to idle a device managed by TISCI
+ * Returns 0 for successful exclusive request, else returns
+ * corresponding error message.
+ * @put_device: Command to release a device managed by TISCI
+ * Returns 0 for successful release, else returns corresponding
+ * error message.
+ * @is_valid: Check if the device ID is a valid ID.
+ * Returns 0 if the ID is valid, else returns corresponding error.
+ * @get_context_loss_count: Command to retrieve context loss counter - this
+ * increments every time the device looses context. Overflow
+ * is possible.
+ * - count: pointer to u32 which will retrieve counter
+ * Returns 0 for successful information request and count has
+ * proper data, else returns corresponding error message.
+ * @is_idle: Reports back about device idle state
+ * - req_state: Returns requested idle state
+ * Returns 0 for successful information request and req_state and
+ * current_state has proper data, else returns corresponding error
+ * message.
+ * @is_stop: Reports back about device stop state
+ * - req_state: Returns requested stop state
+ * - current_state: Returns current stop state
+ * Returns 0 for successful information request and req_state and
+ * current_state has proper data, else returns corresponding error
+ * message.
+ * @is_on: Reports back about device ON(or active) state
+ * - req_state: Returns requested ON state
+ * - current_state: Returns current ON state
+ * Returns 0 for successful information request and req_state and
+ * current_state has proper data, else returns corresponding error
+ * message.
+ * @is_transitioning: Reports back if the device is in the middle of transition
+ * of state.
+ * -current_state: Returns 'true' if currently transitioning.
+ * @set_device_resets: Command to configure resets for device managed by TISCI.
+ * -reset_state: Device specific reset bit field
+ * Returns 0 for successful request, else returns
+ * corresponding error message.
+ * @get_device_resets: Command to read state of resets for device managed
+ * by TISCI.
+ * -reset_state: pointer to u32 which will retrieve resets
+ * Returns 0 for successful request, else returns
+ * corresponding error message.
+ *
+ * NOTE: for all these functions, the following parameters are generic in
+ * nature:
+ * -handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * -id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ */
+struct ti_sci_dev_ops {
+ int (*get_device)(const struct ti_sci_handle *handle, u32 id);
+ int (*idle_device)(const struct ti_sci_handle *handle, u32 id);
+ int (*put_device)(const struct ti_sci_handle *handle, u32 id);
+ int (*is_valid)(const struct ti_sci_handle *handle, u32 id);
+ int (*get_context_loss_count)(const struct ti_sci_handle *handle,
+ u32 id, u32 *count);
+ int (*is_idle)(const struct ti_sci_handle *handle, u32 id,
+ bool *requested_state);
+ int (*is_stop)(const struct ti_sci_handle *handle, u32 id,
+ bool *req_state, bool *current_state);
+ int (*is_on)(const struct ti_sci_handle *handle, u32 id,
+ bool *req_state, bool *current_state);
+ int (*is_transitioning)(const struct ti_sci_handle *handle, u32 id,
+ bool *current_state);
+ int (*set_device_resets)(const struct ti_sci_handle *handle, u32 id,
+ u32 reset_state);
+ int (*get_device_resets)(const struct ti_sci_handle *handle, u32 id,
+ u32 *reset_state);
+};
+
+/**
+ * struct ti_sci_ops - Function support for TI SCI
+ * @dev_ops: Device specific operations
+ */
+struct ti_sci_ops {
+ struct ti_sci_dev_ops dev_ops;
+};
+
/**
* struct ti_sci_handle - Handle returned to TI SCI clients for usage.
* @version: structure containing version information
+ * @ops: operations that are made available to TI SCI clients
*/
struct ti_sci_handle {
struct ti_sci_version_info version;
+ struct ti_sci_ops ops;
};
#if IS_ENABLED(CONFIG_TI_SCI_PROTOCOL)
--
2.10.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH V4 4/5] firmware: ti_sci: Add support for Clock control
2016-10-18 23:08 [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Nishanth Menon
` (2 preceding siblings ...)
2016-10-18 23:08 ` [PATCH V4 3/5] firmware: ti_sci: Add support for Device control Nishanth Menon
@ 2016-10-18 23:08 ` Nishanth Menon
2016-10-18 23:08 ` [PATCH V4 5/5] firmware: ti_sci: Add support for reboot core service Nishanth Menon
2016-10-25 17:34 ` [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Tero Kristo
5 siblings, 0 replies; 11+ messages in thread
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: Tero Kristo, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman, Nishanth Menon
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.
TI-SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.
Introduce support for the set of SCI message protocol support that
provide us with this capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since v3: none
V3: https://patchwork.kernel.org/patch/9317841/
drivers/firmware/ti_sci.c | 685 +++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 289 ++++++++++++++
include/linux/soc/ti/ti_sci_protocol.h | 78 ++++
3 files changed, 1052 insertions(+)
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index c7b25ccf6f07..496a007e5c69 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -902,6 +902,675 @@ static int ti_sci_cmd_get_device_resets(const struct ti_sci_handle *handle,
NULL);
}
+/**
+ * ti_sci_set_clock_state() - Set clock state helper
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @flags: Header flags as needed
+ * @state: State to request for the clock.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_set_clock_state(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id,
+ u32 flags, u8 state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_clock_state *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_CLOCK_STATE,
+ flags | TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_clock_state *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->request_state = state;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_clock_state() - Get clock state helper
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @programmed_state: State requested for clock to move to
+ * @current_state: State that the clock is currently in
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_get_clock_state(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id,
+ u8 *programmed_state, u8 *current_state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_state *req;
+ struct ti_sci_msg_resp_get_clock_state *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ if (!programmed_state && !current_state)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_CLOCK_STATE,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_state *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_state *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp)) {
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ if (programmed_state)
+ *programmed_state = resp->programmed_state;
+ if (current_state)
+ *current_state = resp->current_state;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_clock() - Get control of a clock from TI SCI
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @needs_ssc: 'true' if Spread Spectrum clock is desired, else 'false'
+ * @can_change_freq: 'true' if frequency change is desired, else 'false'
+ * @enable_input_term: 'true' if input termination is desired, else 'false'
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_get_clock(const struct ti_sci_handle *handle, u32 dev_id,
+ u8 clk_id, bool needs_ssc, bool can_change_freq,
+ bool enable_input_term)
+{
+ u32 flags = 0;
+
+ flags |= needs_ssc ? MSG_FLAG_CLOCK_ALLOW_SSC : 0;
+ flags |= can_change_freq ? MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE : 0;
+ flags |= enable_input_term ? MSG_FLAG_CLOCK_INPUT_TERM : 0;
+
+ return ti_sci_set_clock_state(handle, dev_id, clk_id, flags,
+ MSG_CLOCK_SW_STATE_REQ);
+}
+
+/**
+ * ti_sci_cmd_idle_clock() - Idle a clock which is in our control
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ *
+ * NOTE: This clock must have been requested by get_clock previously.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_idle_clock(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id)
+{
+ return ti_sci_set_clock_state(handle, dev_id, clk_id, 0,
+ MSG_CLOCK_SW_STATE_UNREQ);
+}
+
+/**
+ * ti_sci_cmd_put_clock() - Release a clock from our control back to TISCI
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ *
+ * NOTE: This clock must have been requested by get_clock previously.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_put_clock(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id)
+{
+ return ti_sci_set_clock_state(handle, dev_id, clk_id, 0,
+ MSG_CLOCK_SW_STATE_AUTO);
+}
+
+/**
+ * ti_sci_cmd_clk_is_auto() - Is the clock being auto managed
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @req_state: state indicating if the clock is auto managed
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_is_auto(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, bool *req_state)
+{
+ u8 state = 0;
+ int ret;
+
+ if (!req_state)
+ return -EINVAL;
+
+ ret = ti_sci_cmd_get_clock_state(handle, dev_id, clk_id, &state, NULL);
+ if (ret)
+ return ret;
+
+ *req_state = (state == MSG_CLOCK_SW_STATE_AUTO);
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_clk_is_on() - Is the clock ON
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @req_state: state indicating if the clock is managed by us and enabled
+ * @curr_state: state indicating if the clock is ready for operation
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_is_on(const struct ti_sci_handle *handle, u32 dev_id,
+ u8 clk_id, bool *req_state, bool *curr_state)
+{
+ u8 c_state = 0, r_state = 0;
+ int ret;
+
+ if (!req_state && !curr_state)
+ return -EINVAL;
+
+ ret = ti_sci_cmd_get_clock_state(handle, dev_id, clk_id,
+ &r_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (req_state)
+ *req_state = (r_state == MSG_CLOCK_SW_STATE_REQ);
+ if (curr_state)
+ *curr_state = (c_state == MSG_CLOCK_HW_STATE_READY);
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_clk_is_off() - Is the clock OFF
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @req_state: state indicating if the clock is managed by us and disabled
+ * @curr_state: state indicating if the clock is NOT ready for operation
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_is_off(const struct ti_sci_handle *handle, u32 dev_id,
+ u8 clk_id, bool *req_state, bool *curr_state)
+{
+ u8 c_state = 0, r_state = 0;
+ int ret;
+
+ if (!req_state && !curr_state)
+ return -EINVAL;
+
+ ret = ti_sci_cmd_get_clock_state(handle, dev_id, clk_id,
+ &r_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (req_state)
+ *req_state = (r_state == MSG_CLOCK_SW_STATE_UNREQ);
+ if (curr_state)
+ *curr_state = (c_state == MSG_CLOCK_HW_STATE_NOT_READY);
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_clk_set_parent() - Set the clock source of a specific device clock
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @parent_id: Parent clock identifier to set
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_set_parent(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u8 parent_id)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_clock_parent *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_CLOCK_PARENT,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_clock_parent *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->parent_id = parent_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_parent() - Get current parent clock source
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @parent_id: Current clock parent
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_parent(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u8 *parent_id)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_parent *req;
+ struct ti_sci_msg_resp_get_clock_parent *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !parent_id)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_CLOCK_PARENT,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_parent *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_parent *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *parent_id = resp->parent_id;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_num_parents() - Get num parents of the current clk source
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @num_parents: Returns he number of parents to the current clock.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_num_parents(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id,
+ u8 *num_parents)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_num_parents *req;
+ struct ti_sci_msg_resp_get_clock_num_parents *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !num_parents)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_NUM_CLOCK_PARENTS,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_num_parents *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_num_parents *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *num_parents = resp->num_parents;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_match_freq() - Find a good match for frequency
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @min_freq: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq: The target clock frequency in Hz. A frequency will be
+ * processed as close to this target frequency as possible.
+ * @max_freq: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @match_freq: Frequency match in Hz response.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_match_freq(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u64 min_freq,
+ u64 target_freq, u64 max_freq,
+ u64 *match_freq)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_query_clock_freq *req;
+ struct ti_sci_msg_resp_query_clock_freq *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !match_freq)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_QUERY_CLOCK_FREQ,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_query_clock_freq *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->min_freq_hz = min_freq;
+ req->target_freq_hz = target_freq;
+ req->max_freq_hz = max_freq;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_query_clock_freq *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *match_freq = resp->freq_hz;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_set_freq() - Set a frequency for clock
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @min_freq: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq: The target clock frequency in Hz. A frequency will be
+ * processed as close to this target frequency as possible.
+ * @max_freq: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_set_freq(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u64 min_freq,
+ u64 target_freq, u64 max_freq)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_clock_freq *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_CLOCK_FREQ,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_clock_freq *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->min_freq_hz = min_freq;
+ req->target_freq_hz = target_freq;
+ req->max_freq_hz = max_freq;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_freq() - Get current frequency
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @freq: Currently frequency in Hz
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_freq(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u64 *freq)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_freq *req;
+ struct ti_sci_msg_resp_get_clock_freq *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !freq)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_CLOCK_FREQ,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_freq *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_freq *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *freq = resp->freq_hz;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
/*
* ti_sci_setup_ops() - Setup the operations structures
* @info: pointer to TISCI pointer
@@ -910,6 +1579,7 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
{
struct ti_sci_ops *ops = &info->handle.ops;
struct ti_sci_dev_ops *dops = &ops->dev_ops;
+ struct ti_sci_clk_ops *cops = &ops->clk_ops;
dops->get_device = ti_sci_cmd_get_device;
dops->idle_device = ti_sci_cmd_idle_device;
@@ -923,6 +1593,21 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
dops->is_transitioning = ti_sci_cmd_dev_is_trans;
dops->set_device_resets = ti_sci_cmd_set_device_resets;
dops->get_device_resets = ti_sci_cmd_get_device_resets;
+
+ cops->get_clock = ti_sci_cmd_get_clock;
+ cops->idle_clock = ti_sci_cmd_idle_clock;
+ cops->put_clock = ti_sci_cmd_put_clock;
+ cops->is_auto = ti_sci_cmd_clk_is_auto;
+ cops->is_on = ti_sci_cmd_clk_is_on;
+ cops->is_off = ti_sci_cmd_clk_is_off;
+
+ cops->set_parent = ti_sci_cmd_clk_set_parent;
+ cops->get_parent = ti_sci_cmd_clk_get_parent;
+ cops->get_num_parents = ti_sci_cmd_clk_get_num_parents;
+
+ cops->get_best_match_freq = ti_sci_cmd_clk_get_match_freq;
+ cops->set_freq = ti_sci_cmd_clk_set_freq;
+ cops->get_freq = ti_sci_cmd_clk_get_freq;
}
/**
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index 29ce0532a7ca..f69907cfc128 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -52,6 +52,16 @@
#define TI_SCI_MSG_GET_DEVICE_STATE 0x0201
#define TI_SCI_MSG_SET_DEVICE_RESETS 0x0202
+/* Clock requests */
+#define TI_SCI_MSG_SET_CLOCK_STATE 0x0100
+#define TI_SCI_MSG_GET_CLOCK_STATE 0x0101
+#define TI_SCI_MSG_SET_CLOCK_PARENT 0x0102
+#define TI_SCI_MSG_GET_CLOCK_PARENT 0x0103
+#define TI_SCI_MSG_GET_NUM_CLOCK_PARENTS 0x0104
+#define TI_SCI_MSG_SET_CLOCK_FREQ 0x010c
+#define TI_SCI_MSG_QUERY_CLOCK_FREQ 0x010d
+#define TI_SCI_MSG_GET_CLOCK_FREQ 0x010e
+
/**
* struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
* @type: Type of messages: One of TI_SCI_MSG* values
@@ -188,4 +198,283 @@ struct ti_sci_msg_req_set_device_resets {
u32 resets;
} __packed;
+/**
+ * struct ti_sci_msg_req_set_clock_state - Request to setup a Clock state
+ * @hdr: Generic Header, Certain flags can be set specific to the clocks:
+ * MSG_FLAG_CLOCK_ALLOW_SSC: Allow this clock to be modified
+ * via spread spectrum clocking.
+ * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE: Allow this clock's
+ * frequency to be changed while it is running so long as it
+ * is within the min/max limits.
+ * MSG_FLAG_CLOCK_INPUT_TERM: Enable input termination, this
+ * is only applicable to clock inputs on the SoC pseudo-device.
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @request_state: Request the state for the clock to be set to.
+ * MSG_CLOCK_SW_STATE_UNREQ: The IP does not require this clock,
+ * it can be disabled, regardless of the state of the device
+ * MSG_CLOCK_SW_STATE_AUTO: Allow the System Controller to
+ * automatically manage the state of this clock. If the device
+ * is enabled, then the clock is enabled. If the device is set
+ * to off or retention, then the clock is internally set as not
+ * being required by the device.(default)
+ * MSG_CLOCK_SW_STATE_REQ: Configure the clock to be enabled,
+ * regardless of the state of the device.
+ *
+ * Normally, all required clocks are managed by TISCI entity, this is used
+ * only for specific control *IF* required. Auto managed state is
+ * MSG_CLOCK_SW_STATE_AUTO, in other states, TISCI entity assume remote
+ * will explicitly control.
+ *
+ * Request type is TI_SCI_MSG_SET_CLOCK_STATE, response is a generic
+ * ACK or NACK message.
+ */
+struct ti_sci_msg_req_set_clock_state {
+ /* Additional hdr->flags options */
+#define MSG_FLAG_CLOCK_ALLOW_SSC TI_SCI_MSG_FLAG(8)
+#define MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE TI_SCI_MSG_FLAG(9)
+#define MSG_FLAG_CLOCK_INPUT_TERM TI_SCI_MSG_FLAG(10)
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+#define MSG_CLOCK_SW_STATE_UNREQ 0
+#define MSG_CLOCK_SW_STATE_AUTO 1
+#define MSG_CLOCK_SW_STATE_REQ 2
+ u8 request_state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_state - Request for clock state
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to get state of.
+ *
+ * Request type is TI_SCI_MSG_GET_CLOCK_STATE, response is state
+ * of the clock
+ */
+struct ti_sci_msg_req_get_clock_state {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_state - Response to get clock state
+ * @hdr: Generic Header
+ * @programmed_state: Any programmed state of the clock. This is one of
+ * MSG_CLOCK_SW_STATE* values.
+ * @current_state: Current state of the clock. This is one of:
+ * MSG_CLOCK_HW_STATE_NOT_READY: Clock is not ready
+ * MSG_CLOCK_HW_STATE_READY: Clock is ready
+ *
+ * Response to TI_SCI_MSG_GET_CLOCK_STATE.
+ */
+struct ti_sci_msg_resp_get_clock_state {
+ struct ti_sci_msg_hdr hdr;
+ u8 programmed_state;
+#define MSG_CLOCK_HW_STATE_NOT_READY 0
+#define MSG_CLOCK_HW_STATE_READY 1
+ u8 current_state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_set_clock_parent - Set the clock parent
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @parent_id: The new clock parent is selectable by an index via this
+ * parameter.
+ *
+ * Request type is TI_SCI_MSG_SET_CLOCK_PARENT, response is generic
+ * ACK / NACK message.
+ */
+struct ti_sci_msg_req_set_clock_parent {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+ u8 parent_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_parent - Get the clock parent
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to get the parent for.
+ *
+ * Request type is TI_SCI_MSG_GET_CLOCK_PARENT, response is parent information
+ */
+struct ti_sci_msg_req_get_clock_parent {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_parent - Response with clock parent
+ * @hdr: Generic Header
+ * @parent_id: The current clock parent
+ *
+ * Response to TI_SCI_MSG_GET_CLOCK_PARENT.
+ */
+struct ti_sci_msg_resp_get_clock_parent {
+ struct ti_sci_msg_hdr hdr;
+ u8 parent_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_num_parents - Request to get clock parents
+ * @hdr: Generic header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * This request provides information about how many clock parent options
+ * are available for a given clock to a device. This is typically used
+ * for input clocks.
+ *
+ * Request type is TI_SCI_MSG_GET_NUM_CLOCK_PARENTS, response is appropriate
+ * message, or NACK in case of inability to satisfy request.
+ */
+struct ti_sci_msg_req_get_clock_num_parents {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_num_parents - Response for get clk parents
+ * @hdr: Generic header
+ * @num_parents: Number of clock parents
+ *
+ * Response to TI_SCI_MSG_GET_NUM_CLOCK_PARENTS
+ */
+struct ti_sci_msg_resp_get_clock_num_parents {
+ struct ti_sci_msg_hdr hdr;
+ u8 num_parents;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_query_clock_freq - Request to query a frequency
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq_hz: The target clock frequency. A frequency will be found
+ * as close to this target frequency as possible.
+ * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * NOTE: Normally clock frequency management is automatically done by TISCI
+ * entity. In case of specific requests, TISCI evaluates capability to achieve
+ * requested frequency within provided range and responds with
+ * result message.
+ *
+ * Request type is TI_SCI_MSG_QUERY_CLOCK_FREQ, response is appropriate message,
+ * or NACK in case of inability to satisfy request.
+ */
+struct ti_sci_msg_req_query_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u64 min_freq_hz;
+ u64 target_freq_hz;
+ u64 max_freq_hz;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_query_clock_freq - Response to a clock frequency query
+ * @hdr: Generic Header
+ * @freq_hz: Frequency that is the best match in Hz.
+ *
+ * Response to request type TI_SCI_MSG_QUERY_CLOCK_FREQ. NOTE: if the request
+ * cannot be satisfied, the message will be of type NACK.
+ */
+struct ti_sci_msg_resp_query_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u64 freq_hz;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_set_clock_freq - Request to setup a clock frequency
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq_hz: The target clock frequency. The clock will be programmed
+ * at a rate as close to this target frequency as possible.
+ * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * NOTE: Normally clock frequency management is automatically done by TISCI
+ * entity. In case of specific requests, TISCI evaluates capability to achieve
+ * requested range and responds with success/failure message.
+ *
+ * This sets the desired frequency for a clock within an allowable
+ * range. This message will fail on an enabled clock unless
+ * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE is set for the clock. Additionally,
+ * if other clocks have their frequency modified due to this message,
+ * they also must have the MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE or be disabled.
+ *
+ * Calling set frequency on a clock input to the SoC pseudo-device will
+ * inform the PMMC of that clock's frequency. Setting a frequency of
+ * zero will indicate the clock is disabled.
+ *
+ * Calling set frequency on clock outputs from the SoC pseudo-device will
+ * function similarly to setting the clock frequency on a device.
+ *
+ * Request type is TI_SCI_MSG_SET_CLOCK_FREQ, response is a generic ACK/NACK
+ * message.
+ */
+struct ti_sci_msg_req_set_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u64 min_freq_hz;
+ u64 target_freq_hz;
+ u64 max_freq_hz;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_freq - Request to get the clock frequency
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * NOTE: Normally clock frequency management is automatically done by TISCI
+ * entity. In some cases, clock frequencies are configured by host.
+ *
+ * Request type is TI_SCI_MSG_GET_CLOCK_FREQ, responded with clock frequency
+ * that the clock is currently at.
+ */
+struct ti_sci_msg_req_get_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_freq - Response of clock frequency request
+ * @hdr: Generic Header
+ * @freq_hz: Frequency that the clock is currently on, in Hz.
+ *
+ * Response to request type TI_SCI_MSG_GET_CLOCK_FREQ.
+ */
+struct ti_sci_msg_resp_get_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u64 freq_hz;
+} __packed;
+
#endif /* __TI_SCI_H */
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 87fa73851471..76378fddf609 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -115,11 +115,89 @@ struct ti_sci_dev_ops {
};
/**
+ * struct ti_sci_clk_ops - Clock control operations
+ * @get_clock: Request for activation of clock and manage by processor
+ * - needs_ssc: 'true' if Spread Spectrum clock is desired.
+ * - can_change_freq: 'true' if frequency change is desired.
+ * - enable_input_term: 'true' if input termination is desired.
+ * @idle_clock: Request for Idling a clock managed by processor
+ * @put_clock: Release the clock to be auto managed by TISCI
+ * @is_auto: Is the clock being auto managed
+ * - req_state: state indicating if the clock is auto managed
+ * @is_on: Is the clock ON
+ * - req_state: if the clock is requested to be forced ON
+ * - current_state: if the clock is currently ON
+ * @is_off: Is the clock OFF
+ * - req_state: if the clock is requested to be forced OFF
+ * - current_state: if the clock is currently Gated
+ * @set_parent: Set the clock source of a specific device clock
+ * - parent_id: Parent clock identifier to set.
+ * @get_parent: Get the current clock source of a specific device clock
+ * - parent_id: Parent clock identifier which is the parent.
+ * @get_num_parents: Get the number of parents of the current clock source
+ * - num_parents: returns the number of parent clocks.
+ * @get_best_match_freq: Find a best matching frequency for a frequency
+ * range.
+ * - match_freq: Best matching frequency in Hz.
+ * @set_freq: Set the Clock frequency
+ * @get_freq: Get the Clock frequency
+ * - current_freq: Frequency in Hz that the clock is at.
+ *
+ * NOTE: for all these functions, the following parameters are generic in
+ * nature:
+ * -handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * -did: Device identifier this request is for
+ * -cid: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * -min_freq: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * -target_freq: The target clock frequency in Hz. A frequency will be
+ * processed as close to this target frequency as possible.
+ * -max_freq: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ *
+ * Request for the clock - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_clock with put_clock. No refcounting is
+ * managed by driver for that purpose.
+ */
+struct ti_sci_clk_ops {
+ int (*get_clock)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool needs_ssc, bool can_change_freq,
+ bool enable_input_term);
+ int (*idle_clock)(const struct ti_sci_handle *handle, u32 did, u8 cid);
+ int (*put_clock)(const struct ti_sci_handle *handle, u32 did, u8 cid);
+ int (*is_auto)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool *req_state);
+ int (*is_on)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool *req_state, bool *current_state);
+ int (*is_off)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool *req_state, bool *current_state);
+ int (*set_parent)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u8 parent_id);
+ int (*get_parent)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u8 *parent_id);
+ int (*get_num_parents)(const struct ti_sci_handle *handle, u32 did,
+ u8 cid, u8 *num_parents);
+ int (*get_best_match_freq)(const struct ti_sci_handle *handle, u32 did,
+ u8 cid, u64 min_freq, u64 target_freq,
+ u64 max_freq, u64 *match_freq);
+ int (*set_freq)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u64 min_freq, u64 target_freq, u64 max_freq);
+ int (*get_freq)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u64 *current_freq);
+};
+
+/**
* struct ti_sci_ops - Function support for TI SCI
* @dev_ops: Device specific operations
+ * @clk_ops: Clock specific operations
*/
struct ti_sci_ops {
struct ti_sci_dev_ops dev_ops;
+ struct ti_sci_clk_ops clk_ops;
};
/**
--
2.10.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* [PATCH V4 5/5] firmware: ti_sci: Add support for reboot core service
2016-10-18 23:08 [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Nishanth Menon
` (3 preceding siblings ...)
2016-10-18 23:08 ` [PATCH V4 4/5] firmware: ti_sci: Add support for Clock control Nishanth Menon
@ 2016-10-18 23:08 ` Nishanth Menon
2016-10-25 17:34 ` [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Tero Kristo
5 siblings, 0 replies; 11+ messages in thread
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: Tero Kristo, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman, Nishanth Menon
Since system controller now has control over SoC power management, it
needs to be explicitly requested to reboot the SoC. Add support for
it.
In some systems however, SoC needs to toggle a GPIO or send event to an
external entity (like a PMIC) for a system reboot to take place. To
facilitate that, we allow for a DT property to determine if the reboot
handler will be registered and further, the service is also made
available to other drivers (such as PMIC driver) to sequence the
additional operation and trigger the SoC reboot as the last step.
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since V3:
- checkpatch fixes for macro after checkpatch.pl update in v4.9-rc1
V3: https://patchwork.kernel.org/patch/9317837/
drivers/firmware/ti_sci.c | 83 ++++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 12 +++++
include/linux/soc/ti/ti_sci_protocol.h | 11 +++++
3 files changed, 106 insertions(+)
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 496a007e5c69..874ff32db366 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -28,6 +28,7 @@
#include <linux/slab.h>
#include <linux/soc/ti/ti-msgmgr.h>
#include <linux/soc/ti/ti_sci_protocol.h>
+#include <linux/reboot.h>
#include "ti_sci.h"
@@ -90,6 +91,7 @@ struct ti_sci_desc {
* struct ti_sci_info - Structure representing a TI SCI instance
* @dev: Device pointer
* @desc: SoC description for this instance
+ * @nb: Reboot Notifier block
* @d: Debugfs file entry
* @debug_region: Memory region where the debug message are available
* @debug_region_size: Debug region size
@@ -104,6 +106,7 @@ struct ti_sci_desc {
*/
struct ti_sci_info {
struct device *dev;
+ struct notifier_block nb;
const struct ti_sci_desc *desc;
struct dentry *d;
void __iomem *debug_region;
@@ -117,10 +120,12 @@ struct ti_sci_info {
struct list_head node;
/* protected by ti_sci_list_mutex */
int users;
+
};
#define cl_to_ti_sci_info(c) container_of(c, struct ti_sci_info, cl)
#define handle_to_ti_sci_info(h) container_of(h, struct ti_sci_info, handle)
+#define reboot_to_ti_sci_info(n) container_of(n, struct ti_sci_info, nb)
#ifdef CONFIG_DEBUG_FS
@@ -1571,6 +1576,52 @@ static int ti_sci_cmd_clk_get_freq(const struct ti_sci_handle *handle,
return ret;
}
+static int ti_sci_cmd_core_reboot(const struct ti_sci_handle *handle)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_reboot *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SYS_RESET,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_reboot *)xfer->xfer_buf;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ ret = 0;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
/*
* ti_sci_setup_ops() - Setup the operations structures
* @info: pointer to TISCI pointer
@@ -1578,9 +1629,12 @@ static int ti_sci_cmd_clk_get_freq(const struct ti_sci_handle *handle,
static void ti_sci_setup_ops(struct ti_sci_info *info)
{
struct ti_sci_ops *ops = &info->handle.ops;
+ struct ti_sci_core_ops *core_ops = &ops->core_ops;
struct ti_sci_dev_ops *dops = &ops->dev_ops;
struct ti_sci_clk_ops *cops = &ops->clk_ops;
+ core_ops->reboot_device = ti_sci_cmd_core_reboot;
+
dops->get_device = ti_sci_cmd_get_device;
dops->idle_device = ti_sci_cmd_idle_device;
dops->put_device = ti_sci_cmd_put_device;
@@ -1732,6 +1786,18 @@ const struct ti_sci_handle *devm_ti_sci_get_handle(struct device *dev)
}
EXPORT_SYMBOL_GPL(devm_ti_sci_get_handle);
+static int tisci_reboot_handler(struct notifier_block *nb, unsigned long mode,
+ void *cmd)
+{
+ struct ti_sci_info *info = reboot_to_ti_sci_info(nb);
+ const struct ti_sci_handle *handle = &info->handle;
+
+ ti_sci_cmd_core_reboot(handle);
+
+ /* call fail OR pass, we should not be here in the first place */
+ return NOTIFY_BAD;
+}
+
/* Description for K2G */
static const struct ti_sci_desc ti_sci_pmmc_k2g_desc = {
.host_id = 2,
@@ -1759,6 +1825,7 @@ static int ti_sci_probe(struct platform_device *pdev)
struct mbox_client *cl;
int ret = -EINVAL;
int i;
+ int reboot = 0;
of_id = of_match_device(ti_sci_of_match, dev);
if (!of_id) {
@@ -1773,6 +1840,8 @@ static int ti_sci_probe(struct platform_device *pdev)
info->dev = dev;
info->desc = desc;
+ reboot = of_property_read_bool(dev->of_node,
+ "ti,system-reboot-controller");
INIT_LIST_HEAD(&info->node);
minfo = &info->minfo;
@@ -1845,6 +1914,17 @@ static int ti_sci_probe(struct platform_device *pdev)
ti_sci_setup_ops(info);
+ if (reboot) {
+ info->nb.notifier_call = tisci_reboot_handler;
+ info->nb.priority = 128;
+
+ ret = register_restart_handler(&info->nb);
+ if (ret) {
+ dev_err(dev, "reboot registration fail(%d)\n", ret);
+ return ret;
+ }
+ }
+
dev_info(dev, "ABI: %d.%d (firmware rev 0x%04x '%s')\n",
info->handle.version.abi_major, info->handle.version.abi_minor,
info->handle.version.firmware_revision,
@@ -1874,6 +1954,9 @@ static int ti_sci_remove(struct platform_device *pdev)
info = platform_get_drvdata(pdev);
+ if (info->nb.notifier_call)
+ unregister_restart_handler(&info->nb);
+
mutex_lock(&ti_sci_list_mutex);
if (info->users)
ret = -EBUSY;
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index f69907cfc128..9b611e9e6f6d 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -46,6 +46,7 @@
#define TI_SCI_MSG_VERSION 0x0002
#define TI_SCI_MSG_WAKE_REASON 0x0003
#define TI_SCI_MSG_GOODBYE 0x0004
+#define TI_SCI_MSG_SYS_RESET 0x0005
/* Device requests */
#define TI_SCI_MSG_SET_DEVICE_STATE 0x0200
@@ -106,6 +107,17 @@ struct ti_sci_msg_resp_version {
} __packed;
/**
+ * struct ti_sci_msg_req_reboot - Reboot the SoC
+ * @hdr: Generic Header
+ *
+ * Request type is TI_SCI_MSG_SYS_RESET, responded with a generic
+ * ACK/NACK message.
+ */
+struct ti_sci_msg_req_reboot {
+ struct ti_sci_msg_hdr hdr;
+} __packed;
+
+/**
* struct ti_sci_msg_req_set_device_state - Set the desired state of the device
* @hdr: Generic header
* @id: Indicates which device to modify
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 76378fddf609..0ccbc138c26a 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -36,6 +36,16 @@ struct ti_sci_version_info {
struct ti_sci_handle;
/**
+ * struct ti_sci_core_ops - SoC Core Operations
+ * @reboot_device: Reboot the SoC
+ * Returns 0 for successful request(ideally should never return),
+ * else returns corresponding error value.
+ */
+struct ti_sci_core_ops {
+ int (*reboot_device)(const struct ti_sci_handle *handle);
+};
+
+/**
* struct ti_sci_dev_ops - Device control operations
* @get_device: Command to request for device managed by TISCI
* Returns 0 for successful exclusive request, else returns
@@ -196,6 +206,7 @@ struct ti_sci_clk_ops {
* @clk_ops: Clock specific operations
*/
struct ti_sci_ops {
+ struct ti_sci_core_ops core_ops;
struct ti_sci_dev_ops dev_ops;
struct ti_sci_clk_ops clk_ops;
};
--
2.10.0
^ permalink raw reply related [flat|nested] 11+ messages in thread* Re: [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver
2016-10-18 23:08 [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Nishanth Menon
` (4 preceding siblings ...)
2016-10-18 23:08 ` [PATCH V4 5/5] firmware: ti_sci: Add support for reboot core service Nishanth Menon
@ 2016-10-25 17:34 ` Tero Kristo
2016-10-26 19:56 ` Santosh Shilimkar
2016-10-27 16:01 ` Kevin Hilman
5 siblings, 2 replies; 11+ messages in thread
From: Tero Kristo @ 2016-10-25 17:34 UTC (permalink / raw)
To: Nishanth Menon, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman
On 19/10/16 02:08, Nishanth Menon wrote:
> Version 4 of the series is basically a rebase to v4.9-rc1, no functional
> changes.
Hi,
Any final comments on this series, or shall I send a pull-req forward?
Very minimal changes compared to v3 so should be good to go imo.
-Tero
>
> Texas Instruments' Keystone generation System on Chips (SoC)
> starting with 66AK2G02[1], now include a dedicated SoC System Control
> entity called PMMC(Power Management Micro Controller) in line with
> ARM architecture recommendations. The function of this module is
> to integrate all system operations in a centralized location.
> Communication with the SoC System Control entity from various
> processing units like ARM/DSP occurs over Message Manager hardware
> block.
>
> This series adds the base support for TI System Control Interface
> (TI-SCI) protocol[2]. The protocol is built on top of Texas
> Instrument's Message Manager communication mechanism[3].
>
> Overall architecture is very similar to SCPI[4] as follows:
> +-------------+ +---------+ +------^-----+
> | TI SCI GENPD| |TISCI Clk| |TISCI reset |
> +------+------+ +----+----+ +------+-----+
> | | |
> | +----v--------------+ |
> +----------> TISCI Protocol(*) <--+
> +----+--------------+
> |
> +---v-----------+
> | MAILBOX FWK |
> +---+-----------+
> |
> +---v-----------+
> | TI MSGMGR |-> TISCI hardware block
> +---------------+
> (*) This series.
>
>
> V4 of the series is based off v4.9-rc1 and is also available here:
> https://github.com/nmenon/linux-2.6-playground/commits/upstream/v4.10/tisci-base-v4
> Quick boot test: http://pastebin.ubuntu.com/23346183/
>
> Changes since v3:
> - rebase to v4.9-rc1
> - minor checkpatch fixes
>
> V3: https://lkml.org/lkml/2016/9/6/747
> V2: https://lkml.org/lkml/2016/8/30/273
> V1: https://lkml.org/lkml/2016/8/19/768
>
> Nishanth Menon (5):
> Documentation: Add support for TI System Control Interface (TI-SCI)
> protocol
> firmware: Add basic support for TI System Control Interface (TI-SCI)
> protocol
> firmware: ti_sci: Add support for Device control
> firmware: ti_sci: Add support for Clock control
> firmware: ti_sci: Add support for reboot core service
>
> .../devicetree/bindings/arm/keystone/ti,sci.txt | 81 +
> MAINTAINERS | 10 +
> drivers/firmware/Kconfig | 15 +
> drivers/firmware/Makefile | 1 +
> drivers/firmware/ti_sci.c | 1991 ++++++++++++++++++++
> drivers/firmware/ti_sci.h | 492 +++++
> include/linux/soc/ti/ti_sci_protocol.h | 249 +++
> 7 files changed, 2839 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
> create mode 100644 drivers/firmware/ti_sci.c
> create mode 100644 drivers/firmware/ti_sci.h
> create mode 100644 include/linux/soc/ti/ti_sci_protocol.h
>
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver
2016-10-25 17:34 ` [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Tero Kristo
@ 2016-10-26 19:56 ` Santosh Shilimkar
2016-10-27 17:47 ` Tero Kristo
2016-10-27 16:01 ` Kevin Hilman
1 sibling, 1 reply; 11+ messages in thread
From: Santosh Shilimkar @ 2016-10-26 19:56 UTC (permalink / raw)
To: Tero Kristo, Nishanth Menon, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman
On 10/25/2016 10:34 AM, Tero Kristo wrote:
> On 19/10/16 02:08, Nishanth Menon wrote:
>> Version 4 of the series is basically a rebase to v4.9-rc1, no functional
>> changes.
>
> Hi,
>
> Any final comments on this series, or shall I send a pull-req forward?
> Very minimal changes compared to v3 so should be good to go imo.
>
The patchset looks fine to me from brief scan so please Go from
my side at least for the pull request.
Regards,
Santosh
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver
2016-10-26 19:56 ` Santosh Shilimkar
@ 2016-10-27 17:47 ` Tero Kristo
0 siblings, 0 replies; 11+ messages in thread
From: Tero Kristo @ 2016-10-27 17:47 UTC (permalink / raw)
To: Santosh Shilimkar, Nishanth Menon, Santosh Shilimkar
Cc: Dave Gerlach, Lokesh Vutla, Andrew Davis, Russell King,
Russ Dill, Sudeep Holla, linux-arm-kernel, devicetree, linux-pm,
linux-kernel, Rob Herring, Kevin Hilman
On 26/10/16 22:56, Santosh Shilimkar wrote:
> On 10/25/2016 10:34 AM, Tero Kristo wrote:
>> On 19/10/16 02:08, Nishanth Menon wrote:
>>> Version 4 of the series is basically a rebase to v4.9-rc1, no functional
>>> changes.
>>
>> Hi,
>>
>> Any final comments on this series, or shall I send a pull-req forward?
>> Very minimal changes compared to v3 so should be good to go imo.
>>
> The patchset looks fine to me from brief scan so please Go from
> my side at least for the pull request.
Queued for 4.10, pull request sent also. Thanks.
-Tero
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver
2016-10-25 17:34 ` [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver Tero Kristo
2016-10-26 19:56 ` Santosh Shilimkar
@ 2016-10-27 16:01 ` Kevin Hilman
2016-10-27 17:46 ` Tero Kristo
1 sibling, 1 reply; 11+ messages in thread
From: Kevin Hilman @ 2016-10-27 16:01 UTC (permalink / raw)
To: Tero Kristo
Cc: Nishanth Menon, Santosh Shilimkar, Dave Gerlach, Lokesh Vutla,
Andrew Davis, Russell King, Russ Dill, Sudeep Holla,
linux-arm-kernel, devicetree, linux-pm, linux-kernel,
Rob Herring
Tero Kristo <t-kristo@ti.com> writes:
> On 19/10/16 02:08, Nishanth Menon wrote:
>> Version 4 of the series is basically a rebase to v4.9-rc1, no functional
>> changes.
>
> Any final comments on this series, or shall I send a pull-req forward?
> Very minimal changes compared to v3 so should be good to go imo.
Not a comment on the series, but a question on TI-SCI.
Will the uC firmware be open like it was on AM335x?
Kevin
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH V4 0/5] firmware: Add support for TI System Control Interface (TI-SCI) protocol driver
2016-10-27 16:01 ` Kevin Hilman
@ 2016-10-27 17:46 ` Tero Kristo
0 siblings, 0 replies; 11+ messages in thread
From: Tero Kristo @ 2016-10-27 17:46 UTC (permalink / raw)
To: Kevin Hilman
Cc: Nishanth Menon, Santosh Shilimkar, Dave Gerlach, Lokesh Vutla,
Andrew Davis, Russell King, Russ Dill, Sudeep Holla,
linux-arm-kernel, devicetree, linux-pm, linux-kernel,
Rob Herring
On 27/10/16 19:01, Kevin Hilman wrote:
> Tero Kristo <t-kristo@ti.com> writes:
>
>> On 19/10/16 02:08, Nishanth Menon wrote:
>>> Version 4 of the series is basically a rebase to v4.9-rc1, no functional
>>> changes.
>>
>> Any final comments on this series, or shall I send a pull-req forward?
>> Very minimal changes compared to v3 so should be good to go imo.
>
> Not a comment on the series, but a question on TI-SCI.
>
> Will the uC firmware be open like it was on AM335x?
Currently it seems like it will be closed. :(
-Tero
^ permalink raw reply [flat|nested] 11+ messages in thread