[PATCH 4.9 00/59] 4.9.4-stable review

[PATCH 4.9 00/59] 4.9.4-stable review

[Greg Kroah-Hartman]

This is the start of the stable review cycle for the 4.9.4 release.
There are 59 patches in this series, all will be posted as a response
to this one.  If anyone has any issues with these being applied, please
let me know.

Responses should be made by Sun Jan 15 11:38:27 UTC 2017.
Anything received after that time might be too late.

The whole patch series can be found in one patch at:
	kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.4-rc1.gz
or in the git tree and branch at:
  git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    Linux 4.9.4-rc1

Larry Finger <Larry.Finger@lwfinger.net>
    rtlwifi: rtl_usb: Fix missing entry in USB driver's private data

Larry Finger <Larry.Finger@lwfinger.net>
    rtlwifi: Fix enter/exit power_save

Imre Deak <imre.deak@intel.com>
    drm/i915/gen9: Fix PCODE polling during CDCLK change notification

Dennis Kadioglu <denk@post.com>
    ALSA: usb-audio: Add a quirk for Plantronics BT600

Uwe Kleine-König <uwe@kleine-koenig.org>
    spi: mvebu: fix baudrate calculation for armada variant

Grygorii Strashko <grygorii.strashko@ti.com>
    ARM: omap2+: am437x: rollback to use omap3_gptimer_timer_init()

Geert Uytterhoeven <geert@linux-m68k.org>
    ARM: 8631/1: clkdev: Detect errors in clk_hw_register_clkdev() for mass registration

Tony Lindgren <tony@atomide.com>
    ARM: OMAP4+: Fix bad fallthrough for cpuidle

Tony Lindgren <tony@atomide.com>
    ARM: OMAP5: Fix build for PM code

Tony Lindgren <tony@atomide.com>
    ARM: OMAP5: Fix mpuss_early_init

Thomas Gleixner <tglx@linutronix.de>
    bus: arm-ccn: Prevent hotplug callback leak

Chuck Lever <chuck.lever@oracle.com>
    svcrdma: Clear xpt_bc_xps in xprt_setup_rdma_bc() error exit arm

Neil Armstrong <narmstrong@baylibre.com>
    ARM: qcom_defconfig: Fix MDM9515 LCC and GCC config

Kyle Roeschley <kyle.roeschley@ni.com>
    ARM: zynq: Reserve correct amount of non-DMA RAM

Robert Jarzmik <robert.jarzmik@free.fr>
    ARM: pxa: fix pxa25x interrupt init

Andreas Färber <afaerber@suse.de>
    ARM64: dts: bcm2835: Fix bcm2837 compatible string

Andrea Merello <andrea.merello@gmail.com>
    ARM64: dts: bcm2837-rpi-3-b: remove incorrect pwr LED

Matthias Brugger <matthias.bgg@gmail.com>
    arm64: dts: mt8173: Fix auxadc node

Mark Rutland <mark.rutland@arm.com>
    tools/virtio: fix READ_ONCE()

Larry Finger <Larry.Finger@lwfinger.net>
    powerpc: Fix build warning on 32-bit PPC

Takashi Sakamoto <o-takashi@sakamocchi.jp>
    ALSA: firewire-tascam: Fix to handle error from initialization of stream data

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    HID: hid-cypress: validate length of report

David Ahern <dsa@cumulusnetworks.com>
    net: vrf: do not allow table id 0

David Ahern <dsa@cumulusnetworks.com>
    net: ipv4: Fix multipath selection with vrf

Gil Rockah <gilr@mellanox.com>
    net/mlx5e: Remove WARN_ONCE from adaptive moderation code

Herbert Xu <herbert@gondor.apana.org.au>
    gro: Disable frag0 optimization on IPv6 ext headers

Eric Dumazet <edumazet@google.com>
    gro: use min_t() in skb_gro_reset_offset()

Herbert Xu <herbert@gondor.apana.org.au>
    gro: Enter slow-path if there is no tailroom

Anna, Suman <s-anna@ti.com>
    net: add the AF_QIPCRTR entries to family name tables

Florian Fainelli <f.fainelli@gmail.com>
    net: dsa: Ensure validity of dst->ds[0]

hayeswang <hayeswang@realtek.com>
    r8152: fix rx issue for runtime suspend

hayeswang <hayeswang@realtek.com>
    r8152: split rtl8152_suspend function

Florian Fainelli <f.fainelli@gmail.com>
    net: dsa: bcm_sf2: Utilize nested MDIO read/write

Florian Fainelli <f.fainelli@gmail.com>
    net: dsa: bcm_sf2: Do not clobber b53_switch_ops

Daniel Borkmann <daniel@iogearbox.net>
    bpf: change back to orig prog on too many passes

David Ahern <dsa@cumulusnetworks.com>
    net: vrf: Add missing Rx counters

Alexander Duyck <alexander.h.duyck@intel.com>
    ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules

Michal Tesar <mtesar@redhat.com>
    igmp: Make igmp group member RFC 3376 compliant

Ian Kumlien <ian.kumlien@gmail.com>
    flow_dissector: Update pptp handling to avoid null pointer deref.

Reiter Wolfgang <wr0112358@gmail.com>
    drop_monitor: consider inserted data in genlmsg_end

Reiter Wolfgang <wr0112358@gmail.com>
    drop_monitor: add missing call to genlmsg_end

David Ahern <dsa@cumulusnetworks.com>
    net: ipv4: dst for local input routes should use l3mdev if relevant

Wei Zhang <asuka.com@163.com>
    net: fix incorrect original ingress device index in PKTINFO

Mathias Krause <minipli@googlemail.com>
    rtnl: stats - add missing netlink message size checks

Saeed Mahameed <saeedm@mellanox.com>
    net/mlx5e: Disable netdev after close

Saeed Mahameed <saeedm@mellanox.com>
    net/mlx5e: Don't sync netdev state when not registered

Mohamad Haj Yahia <mohamad@mellanox.com>
    net/mlx5: Prevent setting multicast macs for VFs

Maor Gottlieb <maorg@mellanox.com>
    net/mlx5: Mask destination mac value in ethtool steering rules

Eli Cohen <eli@mellanox.com>
    net/mlx5: Avoid shadowing numa_node

Daniel Jurgens <danielj@mellanox.com>
    net/mlx5: Cancel recovery work in remove flow

Noa Osherovich <noaos@mellanox.com>
    net/mlx5: Check FW limitations on log_max_qp before setting it

Paul Blakey <paulb@mellanox.com>
    net/sched: cls_flower: Fix missing addr_type in classify

Florian Fainelli <f.fainelli@gmail.com>
    net: stmmac: Fix race between stmmac_drv_probe and stmmac_open

Daniel Borkmann <daniel@iogearbox.net>
    net, sched: fix soft lockup in tc_classify

Dave Jones <davej@codemonkey.org.uk>
    ipv6: handle -EFAULT from skb_copy_bits

Willem de Bruijn <willemb@google.com>
    inet: fix IP(V6)_RECVORIGDSTADDR for udp sockets

Xin Long <lucien.xin@gmail.com>
    sctp: sctp_transport_lookup_process should rcu_read_unlock when transport is null

David Ahern <dsa@cumulusnetworks.com>
    net: vrf: Drop conntrack data after pass through VRF device on Tx

David Ahern <dsa@cumulusnetworks.com>
    net: vrf: Fix NAT within a VRF


-------------

Diffstat:

 Makefile                                           |  4 +-
 arch/arm/configs/qcom_defconfig                    |  4 +-
 arch/arm/mach-omap2/Makefile                       |  2 +-
 arch/arm/mach-omap2/board-generic.c                |  2 +-
 arch/arm/mach-omap2/common.h                       | 38 +++++++---
 arch/arm/mach-omap2/io.c                           |  3 +-
 arch/arm/mach-omap2/omap-mpuss-lowpower.c          | 37 +++++++---
 arch/arm/mach-omap2/omap4-sar-layout.h             |  2 +
 arch/arm/mach-omap2/timer.c                        |  9 +--
 arch/arm/mach-pxa/pxa25x.c                         |  2 +-
 arch/arm/mach-zynq/common.c                        |  2 +-
 arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts   |  7 --
 arch/arm64/boot/dts/broadcom/bcm2837.dtsi          |  2 +-
 arch/arm64/boot/dts/mediatek/mt8173.dtsi           |  3 +
 arch/powerpc/kernel/misc_32.S                      |  2 +-
 arch/x86/net/bpf_jit_comp.c                        |  2 +
 drivers/bus/arm-ccn.c                              |  5 +-
 drivers/clk/clkdev.c                               |  8 +++
 drivers/gpu/drm/i915/i915_drv.h                    |  2 +
 drivers/gpu/drm/i915/intel_display.c               | 31 +++-----
 drivers/gpu/drm/i915/intel_pm.c                    | 75 +++++++++++++++++++
 drivers/hid/hid-cypress.c                          |  3 +
 drivers/net/dsa/bcm_sf2.c                          | 11 ++-
 .../ethernet/mellanox/mlx5/core/en_fs_ethtool.c    |  1 +
 drivers/net/ethernet/mellanox/mlx5/core/en_main.c  | 27 ++++---
 drivers/net/ethernet/mellanox/mlx5/core/en_rx_am.c |  7 +-
 drivers/net/ethernet/mellanox/mlx5/core/eswitch.c  |  2 +-
 drivers/net/ethernet/mellanox/mlx5/core/main.c     | 15 ++--
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c  | 23 +++---
 drivers/net/usb/r8152.c                            | 80 ++++++++++++++++-----
 drivers/net/vrf.c                                  | 13 +++-
 drivers/net/wireless/realtek/rtlwifi/base.c        |  8 +--
 drivers/net/wireless/realtek/rtlwifi/core.c        |  9 +--
 drivers/net/wireless/realtek/rtlwifi/pci.c         | 14 ++--
 drivers/net/wireless/realtek/rtlwifi/ps.c          | 36 +++++++---
 drivers/net/wireless/realtek/rtlwifi/usb.c         |  1 +
 drivers/spi/spi-orion.c                            | 83 ++++++++++++++--------
 include/linux/netdevice.h                          |  9 ++-
 net/core/dev.c                                     |  4 +-
 net/core/drop_monitor.c                            | 39 +++++++---
 net/core/flow_dissector.c                          |  5 +-
 net/core/rtnetlink.c                               |  6 ++
 net/core/sock.c                                    |  6 +-
 net/dsa/dsa2.c                                     | 11 +--
 net/ipv4/fib_frontend.c                            |  2 +-
 net/ipv4/fib_semantics.c                           |  9 ++-
 net/ipv4/igmp.c                                    |  7 +-
 net/ipv4/ip_sockglue.c                             | 10 ++-
 net/ipv4/route.c                                   |  3 +-
 net/ipv6/datagram.c                                |  2 +-
 net/ipv6/ip6_offload.c                             |  1 +
 net/ipv6/raw.c                                     |  6 +-
 net/sched/cls_api.c                                |  4 +-
 net/sched/cls_flower.c                             |  4 ++
 net/sctp/socket.c                                  |  5 +-
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c         |  1 +
 sound/firewire/tascam/tascam-stream.c              |  2 +-
 sound/usb/quirks.c                                 |  1 +
 tools/virtio/linux/compiler.h                      |  2 +-
 59 files changed, 508 insertions(+), 206 deletions(-)

[PATCH 4.9 01/59] net: vrf: Fix NAT within a VRF

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: David Ahern <dsa@cumulusnetworks.com>


[ Upstream commit a0f37efa82253994b99623dbf41eea8dd0ba169b ]

Connection tracking with VRF is broken because the pass through the VRF
device drops the connection tracking info. Removing the call to nf_reset
allows DNAT and MASQUERADE to work across interfaces within a VRF.

Fixes: 73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/vrf.c |    2 --
 1 file changed, 2 deletions(-)

--- a/drivers/net/vrf.c
+++ b/drivers/net/vrf.c
@@ -850,8 +850,6 @@ static struct sk_buff *vrf_rcv_nfhook(u8
 {
 	struct net *net = dev_net(dev);
 
-	nf_reset(skb);
-
 	if (NF_HOOK(pf, hook, net, NULL, skb, dev, NULL, vrf_rcv_finish) < 0)
 		skb = NULL;    /* kfree_skb(skb) handled by nf code */
 

[PATCH 4.9 02/59] net: vrf: Drop conntrack data after pass through VRF device on Tx

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: David Ahern <dsa@cumulusnetworks.com>


[ Upstream commit eb63ecc1706b3e094d0f57438b6c2067cfc299f2 ]

Locally originated traffic in a VRF fails in the presence of a POSTROUTING
rule. For example,

    $ iptables -t nat -A POSTROUTING -s 11.1.1.0/24  -j MASQUERADE
    $ ping -I red -c1 11.1.1.3
    ping: Warning: source address might be selected on device other than red.
    PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data.
    ping: sendmsg: Operation not permitted

Worse, the above causes random corruption resulting in a panic in random
places (I have not seen a consistent backtrace).

Call nf_reset to drop the conntrack info following the pass through the
VRF device.  The nf_reset is needed on Tx but not Rx because of the order
in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress
device and on Tx it is is before the real egress device. Connection
tracking should be tied to the real egress device and not the VRF device.

Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device")
Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/vrf.c |    4 ++++
 1 file changed, 4 insertions(+)

--- a/drivers/net/vrf.c
+++ b/drivers/net/vrf.c
@@ -371,6 +371,8 @@ static int vrf_finish_output6(struct net
 	struct in6_addr *nexthop;
 	int ret;
 
+	nf_reset(skb);
+
 	skb->protocol = htons(ETH_P_IPV6);
 	skb->dev = dev;
 
@@ -552,6 +554,8 @@ static int vrf_finish_output(struct net
 	u32 nexthop;
 	int ret = -EINVAL;
 
+	nf_reset(skb);
+
 	/* Be paranoid, rather than too clever. */
 	if (unlikely(skb_headroom(skb) < hh_len && dev->header_ops)) {
 		struct sk_buff *skb2;

[PATCH 4.9 03/59] sctp: sctp_transport_lookup_process should rcu_read_unlock when transport is null

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Xin Long <lucien.xin@gmail.com>


[ Upstream commit 08abb79542c9e8c367d1d8e44fe1026868d3f0a7 ]

Prior to this patch, sctp_transport_lookup_process didn't rcu_read_unlock
when it failed to find a transport by sctp_addrs_lookup_transport.

This patch is to fix it by moving up rcu_read_unlock right before checking
transport and also to remove the out path.

Fixes: 1cceda784980 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/sctp/socket.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/net/sctp/socket.c
+++ b/net/sctp/socket.c
@@ -4479,9 +4479,10 @@ int sctp_transport_lookup_process(int (*
 
 	rcu_read_lock();
 	transport = sctp_addrs_lookup_transport(net, laddr, paddr);
-	if (!transport || !sctp_transport_hold(transport))
+	if (!transport || !sctp_transport_hold(transport)) {
+		rcu_read_unlock();
 		goto out;
-
+	}
 	rcu_read_unlock();
 	err = cb(transport, p);
 	sctp_transport_put(transport);

[PATCH 4.9 04/59] inet: fix IP(V6)_RECVORIGDSTADDR for udp sockets

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Willem de Bruijn <willemb@google.com>


[ Upstream commit 39b2dd765e0711e1efd1d1df089473a8dd93ad48 ]

Socket cmsg IP(V6)_RECVORIGDSTADDR checks that port range lies within
the packet. For sockets that have transport headers pulled, transport
offset can be negative. Use signed comparison to avoid overflow.

Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Reported-by: Nisar Jagabar <njagabar@cloudmark.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/ip_sockglue.c |    2 +-
 net/ipv6/datagram.c    |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

--- a/net/ipv4/ip_sockglue.c
+++ b/net/ipv4/ip_sockglue.c
@@ -137,7 +137,7 @@ static void ip_cmsg_recv_dstaddr(struct
 	const struct iphdr *iph = ip_hdr(skb);
 	__be16 *ports = (__be16 *)skb_transport_header(skb);
 
-	if (skb_transport_offset(skb) + 4 > skb->len)
+	if (skb_transport_offset(skb) + 4 > (int)skb->len)
 		return;
 
 	/* All current transport protocols have the port numbers in the
--- a/net/ipv6/datagram.c
+++ b/net/ipv6/datagram.c
@@ -700,7 +700,7 @@ void ip6_datagram_recv_specific_ctl(stru
 		struct sockaddr_in6 sin6;
 		__be16 *ports = (__be16 *) skb_transport_header(skb);
 
-		if (skb_transport_offset(skb) + 4 <= skb->len) {
+		if (skb_transport_offset(skb) + 4 <= (int)skb->len) {
 			/* All current transport protocols have the port numbers in the
 			 * first four bytes of the transport header and this function is
 			 * written with this assumption in mind.

[PATCH 4.9 05/59] ipv6: handle -EFAULT from skb_copy_bits

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Dave Jones <davej@codemonkey.org.uk>


[ Upstream commit a98f91758995cb59611e61318dddd8a6956b52c3 ]

By setting certain socket options on ipv6 raw sockets, we can confuse the
length calculation in rawv6_push_pending_frames triggering a BUG_ON.

RIP: 0010:[<ffffffff817c6390>] [<ffffffff817c6390>] rawv6_sendmsg+0xc30/0xc40
RSP: 0018:ffff881f6c4a7c18  EFLAGS: 00010282
RAX: 00000000fffffff2 RBX: ffff881f6c681680 RCX: 0000000000000002
RDX: ffff881f6c4a7cf8 RSI: 0000000000000030 RDI: ffff881fed0f6a00
RBP: ffff881f6c4a7da8 R08: 0000000000000000 R09: 0000000000000009
R10: ffff881fed0f6a00 R11: 0000000000000009 R12: 0000000000000030
R13: ffff881fed0f6a00 R14: ffff881fee39ba00 R15: ffff881fefa93a80

Call Trace:
 [<ffffffff8118ba23>] ? unmap_page_range+0x693/0x830
 [<ffffffff81772697>] inet_sendmsg+0x67/0xa0
 [<ffffffff816d93f8>] sock_sendmsg+0x38/0x50
 [<ffffffff816d982f>] SYSC_sendto+0xef/0x170
 [<ffffffff816da27e>] SyS_sendto+0xe/0x10
 [<ffffffff81002910>] do_syscall_64+0x50/0xa0
 [<ffffffff817f7cbc>] entry_SYSCALL64_slow_path+0x25/0x25

Handle by jumping to the failure path if skb_copy_bits gets an EFAULT.

Reproducer:

#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <unistd.h>
#include <sys/types.h>
#include <sys/socket.h>
#include <netinet/in.h>

#define LEN 504

int main(int argc, char* argv[])
{
	int fd;
	int zero = 0;
	char buf[LEN];

	memset(buf, 0, LEN);

	fd = socket(AF_INET6, SOCK_RAW, 7);

	setsockopt(fd, SOL_IPV6, IPV6_CHECKSUM, &zero, 4);
	setsockopt(fd, SOL_IPV6, IPV6_DSTOPTS, &buf, LEN);

	sendto(fd, buf, 1, 0, (struct sockaddr *) buf, 110);
}

Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv6/raw.c |    6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

--- a/net/ipv6/raw.c
+++ b/net/ipv6/raw.c
@@ -589,7 +589,11 @@ static int rawv6_push_pending_frames(str
 	}
 
 	offset += skb_transport_offset(skb);
-	BUG_ON(skb_copy_bits(skb, offset, &csum, 2));
+	err = skb_copy_bits(skb, offset, &csum, 2);
+	if (err < 0) {
+		ip6_flush_pending_frames(sk);
+		goto out;
+	}
 
 	/* in case cksum was not initialized */
 	if (unlikely(csum))

[PATCH 4.9 06/59] net, sched: fix soft lockup in tc_classify

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Daniel Borkmann <daniel@iogearbox.net>


[ Upstream commit 628185cfddf1dfb701c4efe2cfd72cf5b09f5702 ]

Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.

What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.

This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.

This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.

tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.

Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit
12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").

Fixes: 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup")
Reported-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/sched/cls_api.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/net/sched/cls_api.c
+++ b/net/sched/cls_api.c
@@ -148,13 +148,15 @@ static int tc_ctl_tfilter(struct sk_buff
 	unsigned long cl;
 	unsigned long fh;
 	int err;
-	int tp_created = 0;
+	int tp_created;
 
 	if ((n->nlmsg_type != RTM_GETTFILTER) &&
 	    !netlink_ns_capable(skb, net->user_ns, CAP_NET_ADMIN))
 		return -EPERM;
 
 replay:
+	tp_created = 0;
+
 	err = nlmsg_parse(n, sizeof(*t), tca, TCA_MAX, NULL);
 	if (err < 0)
 		return err;

[PATCH 4.9 07/59] net: stmmac: Fix race between stmmac_drv_probe and stmmac_open

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Florian Fainelli <f.fainelli@gmail.com>


[ Upstream commit 5701659004d68085182d2fd4199c79172165fa65 ]

There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:

[  473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
                stmmac_dvr_probe: warning: cannot get CSR clock
[  473.919382] stmmaceth 0000:01:00.0: no reset control found
[  473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[  473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[  473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[  473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[  473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
                Enable RX Mitigation via HW Watchdog Timer
[  473.921395] libphy: PHY stmmac-1:00 not found
[  473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[  473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
                PHY (error: -19)
[  473.959710] libphy: stmmac: probed
[  473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
                (stmmac-1:00) active
[  473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
                (stmmac-1:01)
[  473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
                (stmmac-1:02)
[  473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
                (stmmac-1:03)

Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.

Fixes: 4bfcbd7abce2 ("stmmac: Move the mdio_register/_unregister in probe/remove")
Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |   23 ++++++++++++----------
 1 file changed, 13 insertions(+), 10 deletions(-)

--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3349,12 +3349,6 @@ int stmmac_dvr_probe(struct device *devi
 	spin_lock_init(&priv->lock);
 	spin_lock_init(&priv->tx_lock);
 
-	ret = register_netdev(ndev);
-	if (ret) {
-		pr_err("%s: ERROR %i registering the device\n", __func__, ret);
-		goto error_netdev_register;
-	}
-
 	/* If a specific clk_csr value is passed from the platform
 	 * this means that the CSR Clock Range selection cannot be
 	 * changed at run-time and it is fixed. Viceversa the driver'll try to
@@ -3376,15 +3370,24 @@ int stmmac_dvr_probe(struct device *devi
 		if (ret < 0) {
 			pr_debug("%s: MDIO bus (id: %d) registration failed",
 				 __func__, priv->plat->bus_id);
-			goto error_mdio_register;
+			goto error_napi_register;
 		}
 	}
 
-	return 0;
+	ret = register_netdev(ndev);
+	if (ret) {
+		pr_err("%s: ERROR %i registering the device\n", __func__, ret);
+		goto error_netdev_register;
+	}
+
+	return ret;
 
-error_mdio_register:
-	unregister_netdev(ndev);
 error_netdev_register:
+	if (priv->hw->pcs != STMMAC_PCS_RGMII &&
+	    priv->hw->pcs != STMMAC_PCS_TBI &&
+	    priv->hw->pcs != STMMAC_PCS_RTBI)
+		stmmac_mdio_unregister(ndev);
+error_napi_register:
 	netif_napi_del(&priv->napi);
 error_hw_init:
 	clk_disable_unprepare(priv->pclk);

[PATCH 4.9 08/59] net/sched: cls_flower: Fix missing addr_type in classify

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Paul Blakey <paulb@mellanox.com>


[ Upstream commit 0df0f207aab4f42e5c96a807adf9a6845b69e984 ]

Since we now use a non zero mask on addr_type, we are matching on its
value (IPV4/IPV6). So before this fix, matching on enc_src_ip/enc_dst_ip
failed in SW/classify path since its value was zero.
This patch sets the proper value of addr_type for encapsulated packets.

Fixes: 970bfcd09791 ('net/sched: cls_flower: Use mask for addr_type')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/sched/cls_flower.c |    4 ++++
 1 file changed, 4 insertions(+)

--- a/net/sched/cls_flower.c
+++ b/net/sched/cls_flower.c
@@ -149,10 +149,14 @@ static int fl_classify(struct sk_buff *s
 
 		switch (ip_tunnel_info_af(info)) {
 		case AF_INET:
+			skb_key.enc_control.addr_type =
+				FLOW_DISSECTOR_KEY_IPV4_ADDRS;
 			skb_key.enc_ipv4.src = key->u.ipv4.src;
 			skb_key.enc_ipv4.dst = key->u.ipv4.dst;
 			break;
 		case AF_INET6:
+			skb_key.enc_control.addr_type =
+				FLOW_DISSECTOR_KEY_IPV6_ADDRS;
 			skb_key.enc_ipv6.src = key->u.ipv6.src;
 			skb_key.enc_ipv6.dst = key->u.ipv6.dst;
 			break;

[PATCH 4.9 09/59] net/mlx5: Check FW limitations on log_max_qp before setting it

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Noa Osherovich <noaos@mellanox.com>


[ Upstream commit 883371c453b937f9eb581fb4915210865982736f ]

When setting HCA capabilities, set log_max_qp to be the minimum
between the selected profile's value and the HCA limitation.

Fixes: 938fe83c8dcb ('net/mlx5_core: New device capabilities...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/main.c |    7 +++++++
 1 file changed, 7 insertions(+)

--- a/drivers/net/ethernet/mellanox/mlx5/core/main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c
@@ -468,6 +468,13 @@ static int handle_hca_cap(struct mlx5_co
 	MLX5_SET(cmd_hca_cap, set_hca_cap, pkey_table_size,
 		 to_fw_pkey_sz(dev, 128));
 
+	/* Check log_max_qp from HCA caps to set in current profile */
+	if (MLX5_CAP_GEN_MAX(dev, log_max_qp) < profile[prof_sel].log_max_qp) {
+		mlx5_core_warn(dev, "log_max_qp value in current profile is %d, changing it to HCA capability limit (%d)\n",
+			       profile[prof_sel].log_max_qp,
+			       MLX5_CAP_GEN_MAX(dev, log_max_qp));
+		profile[prof_sel].log_max_qp = MLX5_CAP_GEN_MAX(dev, log_max_qp);
+	}
 	if (prof->mask & MLX5_PROF_MASK_QP_SIZE)
 		MLX5_SET(cmd_hca_cap, set_hca_cap, log_max_qp,
 			 prof->log_max_qp);

[PATCH 4.9 10/59] net/mlx5: Cancel recovery work in remove flow

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Daniel Jurgens <danielj@mellanox.com>


[ Upstream commit 689a248df83b6032edc57e86267b4e5cc8d7174e ]

If there is pending delayed work for health recovery it must be canceled
if the device is being unloaded.

Fixes: 05ac2c0b7438 ("net/mlx5: Fix race between PCI error handlers and health work")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/main.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/drivers/net/ethernet/mellanox/mlx5/core/main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c
@@ -1159,6 +1159,8 @@ static int mlx5_unload_one(struct mlx5_c
 {
 	int err = 0;
 
+	mlx5_drain_health_wq(dev);
+
 	mutex_lock(&dev->intf_state_mutex);
 	if (test_bit(MLX5_INTERFACE_STATE_DOWN, &dev->intf_state)) {
 		dev_warn(&dev->pdev->dev, "%s: interface is down, NOP\n",
@@ -1319,10 +1321,9 @@ static pci_ers_result_t mlx5_pci_err_det
 
 	mlx5_enter_error_state(dev);
 	mlx5_unload_one(dev, priv, false);
-	/* In case of kernel call save the pci state and drain health wq */
+	/* In case of kernel call save the pci state */
 	if (state) {
 		pci_save_state(pdev);
-		mlx5_drain_health_wq(dev);
 		mlx5_pci_disable_device(dev);
 	}
 

[PATCH 4.9 11/59] net/mlx5: Avoid shadowing numa_node

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Eli Cohen <eli@mellanox.com>


[ Upstream commit d151d73dcc99de87c63bdefebcc4cb69de1cdc40 ]

Avoid using a local variable named numa_node to avoid shadowing a public
one.

Fixes: db058a186f98 ('net/mlx5_core: Set irq affinity hints')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/main.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

--- a/drivers/net/ethernet/mellanox/mlx5/core/main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c
@@ -547,7 +547,6 @@ static int mlx5_irq_set_affinity_hint(st
 	struct mlx5_priv *priv  = &mdev->priv;
 	struct msix_entry *msix = priv->msix_arr;
 	int irq                 = msix[i + MLX5_EQ_VEC_COMP_BASE].vector;
-	int numa_node           = priv->numa_node;
 	int err;
 
 	if (!zalloc_cpumask_var(&priv->irq_info[i].mask, GFP_KERNEL)) {
@@ -555,7 +554,7 @@ static int mlx5_irq_set_affinity_hint(st
 		return -ENOMEM;
 	}
 
-	cpumask_set_cpu(cpumask_local_spread(i, numa_node),
+	cpumask_set_cpu(cpumask_local_spread(i, priv->numa_node),
 			priv->irq_info[i].mask);
 
 	err = irq_set_affinity_hint(irq, priv->irq_info[i].mask);

[PATCH 4.9 12/59] net/mlx5: Mask destination mac value in ethtool steering rules

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Maor Gottlieb <maorg@mellanox.com>


[ Upstream commit 077b1e8069b9b74477b01d28f6b83774dc19a142 ]

We need to mask the destination mac value with the destination mac
mask when adding steering rule via ethtool.

Fixes: 1174fce8d1410 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/en_fs_ethtool.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/net/ethernet/mellanox/mlx5/core/en_fs_ethtool.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_fs_ethtool.c
@@ -247,6 +247,7 @@ static int set_flow_attrs(u32 *match_c,
 	}
 	if (fs->flow_type & FLOW_MAC_EXT &&
 	    !is_zero_ether_addr(fs->m_ext.h_dest)) {
+		mask_spec(fs->m_ext.h_dest, fs->h_ext.h_dest, ETH_ALEN);
 		ether_addr_copy(MLX5_ADDR_OF(fte_match_set_lyr_2_4,
 					     outer_headers_c, dmac_47_16),
 				fs->m_ext.h_dest);

[PATCH 4.9 13/59] net/mlx5: Prevent setting multicast macs for VFs

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Mohamad Haj Yahia <mohamad@mellanox.com>


[ Upstream commit ccce1700263d8b5b219359d04180492a726cea16 ]

Need to check that VF mac address entered by the admin user is either
zero or unicast mac.
Multicast mac addresses are prohibited.

Fixes: 77256579c6b4 ('net/mlx5: E-Switch, Introduce Vport administration functions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/eswitch.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/eswitch.c
@@ -1703,7 +1703,7 @@ int mlx5_eswitch_set_vport_mac(struct ml
 
 	if (!ESW_ALLOWED(esw))
 		return -EPERM;
-	if (!LEGAL_VPORT(esw, vport))
+	if (!LEGAL_VPORT(esw, vport) || is_multicast_ether_addr(mac))
 		return -EINVAL;
 
 	mutex_lock(&esw->state_lock);

[PATCH 4.9 14/59] net/mlx5e: Dont sync netdev state when not registered

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Saeed Mahameed <saeedm@mellanox.com>


[ Upstream commit 610e89e05c3f28a7394935aa6b91f99548c4fd3c ]

Skip setting netdev vxlan ports and netdev rx_mode on driver load
when netdev is not yet registered.

Synchronizing with netdev state is needed only on reset flow where the
netdev remains registered for the whole reset period.

This also fixes an access before initialization of net_device.addr_list_lock
- which for some reason initialized on register_netdev - where we queued
set_rx_mode work on driver load before netdev registration.

Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/en_main.c |   19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)

--- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
@@ -3773,14 +3773,7 @@ static void mlx5e_nic_enable(struct mlx5
 
 	mlx5_lag_add(mdev, netdev);
 
-	if (mlx5e_vxlan_allowed(mdev)) {
-		rtnl_lock();
-		udp_tunnel_get_rx_info(netdev);
-		rtnl_unlock();
-	}
-
 	mlx5e_enable_async_events(priv);
-	queue_work(priv->wq, &priv->set_rx_mode_work);
 
 	if (MLX5_CAP_GEN(mdev, vport_group_manager)) {
 		mlx5_query_nic_vport_mac_address(mdev, 0, rep.hw_id);
@@ -3790,6 +3783,18 @@ static void mlx5e_nic_enable(struct mlx5
 		rep.priv_data = priv;
 		mlx5_eswitch_register_vport_rep(esw, 0, &rep);
 	}
+
+	if (netdev->reg_state != NETREG_REGISTERED)
+		return;
+
+	/* Device already registered: sync netdev system state */
+	if (mlx5e_vxlan_allowed(mdev)) {
+		rtnl_lock();
+		udp_tunnel_get_rx_info(netdev);
+		rtnl_unlock();
+	}
+
+	queue_work(priv->wq, &priv->set_rx_mode_work);
 }
 
 static void mlx5e_nic_disable(struct mlx5e_priv *priv)

[PATCH 4.9 15/59] net/mlx5e: Disable netdev after close

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Saeed Mahameed <saeedm@mellanox.com>


[ Upstream commit 37f304d10030bb425c19099e7b955d9c3ec4cba3 ]

Disable netdev should come after it was closed, although no harm of doing it
before -hence the MLX5E_STATE_DESTROYING bit- but it is more natural this way.

Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/en_main.c |    8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

--- a/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_main.c
@@ -3942,10 +3942,6 @@ void mlx5e_detach_netdev(struct mlx5_cor
 	const struct mlx5e_profile *profile = priv->profile;
 
 	set_bit(MLX5E_STATE_DESTROYING, &priv->state);
-	if (profile->disable)
-		profile->disable(priv);
-
-	flush_workqueue(priv->wq);
 
 	rtnl_lock();
 	if (netif_running(netdev))
@@ -3953,6 +3949,10 @@ void mlx5e_detach_netdev(struct mlx5_cor
 	netif_device_detach(netdev);
 	rtnl_unlock();
 
+	if (profile->disable)
+		profile->disable(priv);
+	flush_workqueue(priv->wq);
+
 	mlx5e_destroy_q_counter(priv);
 	profile->cleanup_rx(priv);
 	mlx5e_close_drop_rq(priv);

[PATCH 4.9 16/59] rtnl: stats - add missing netlink message size checks

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Mathias Krause <minipli@googlemail.com>


[ Upstream commit 4775cc1f2d5abca894ac32774eefc22c45347d1c ]

We miss to check if the netlink message is actually big enough to contain
a struct if_stats_msg.

Add a check to prevent userland from sending us short messages that would
make us access memory beyond the end of the message.

Fixes: 10c9ead9f3c6 ("rtnetlink: add new RTM_GETSTATS message to dump...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/rtnetlink.c |    6 ++++++
 1 file changed, 6 insertions(+)

--- a/net/core/rtnetlink.c
+++ b/net/core/rtnetlink.c
@@ -3886,6 +3886,9 @@ static int rtnl_stats_get(struct sk_buff
 	u32 filter_mask;
 	int err;
 
+	if (nlmsg_len(nlh) < sizeof(*ifsm))
+		return -EINVAL;
+
 	ifsm = nlmsg_data(nlh);
 	if (ifsm->ifindex > 0)
 		dev = __dev_get_by_index(net, ifsm->ifindex);
@@ -3935,6 +3938,9 @@ static int rtnl_stats_dump(struct sk_buf
 
 	cb->seq = net->dev_base_seq;
 
+	if (nlmsg_len(cb->nlh) < sizeof(*ifsm))
+		return -EINVAL;
+
 	ifsm = nlmsg_data(cb->nlh);
 	filter_mask = ifsm->filter_mask;
 	if (!filter_mask)

[PATCH 4.9 17/59] net: fix incorrect original ingress device index in PKTINFO

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Wei Zhang <asuka.com@163.com>


[ Upstream commit f0c16ba8933ed217c2688b277410b2a37ba81591 ]

When we send a packet for our own local address on a non-loopback
interface (e.g. eth0), due to the change had been introduced from
commit 0b922b7a829c ("net: original ingress device index in PKTINFO"), the
original ingress device index would be set as the loopback interface.
However, the packet should be considered as if it is being arrived via the
sending interface (eth0), otherwise it would break the expectation of the
userspace application (e.g. the DHCPRELEASE message from dhcp_release
binary would be ignored by the dnsmasq daemon, since it come from lo which
is not the interface dnsmasq bind to)

Fixes: 0b922b7a829c ("net: original ingress device index in PKTINFO")
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Wei Zhang <asuka.com@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/ip_sockglue.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

--- a/net/ipv4/ip_sockglue.c
+++ b/net/ipv4/ip_sockglue.c
@@ -1202,8 +1202,14 @@ void ipv4_pktinfo_prepare(const struct s
 		 * which has interface index (iif) as the first member of the
 		 * underlying inet{6}_skb_parm struct. This code then overlays
 		 * PKTINFO_SKB_CB and in_pktinfo also has iif as the first
-		 * element so the iif is picked up from the prior IPCB
+		 * element so the iif is picked up from the prior IPCB. If iif
+		 * is the loopback interface, then return the sending interface
+		 * (e.g., process binds socket to eth0 for Tx which is
+		 * redirected to loopback in the rtable/dst).
 		 */
+		if (pktinfo->ipi_ifindex == LOOPBACK_IFINDEX)
+			pktinfo->ipi_ifindex = inet_iif(skb);
+
 		pktinfo->ipi_spec_dst.s_addr = fib_compute_spec_dst(skb);
 	} else {
 		pktinfo->ipi_ifindex = 0;

[PATCH 4.9 18/59] net: ipv4: dst for local input routes should use l3mdev if relevant

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: David Ahern <dsa@cumulusnetworks.com>


[ Upstream commit f5a0aab84b74de68523599817569c057c7ac1622 ]

IPv4 output routes already use l3mdev device instead of loopback for dst's
if it is applicable. Change local input routes to do the same.

This fixes icmp responses for unreachable UDP ports which are directed
to the wrong table after commit 9d1a6c4ea43e4 because local_input
routes use the loopback device. Moving from ingress device to loopback
loses the L3 domain causing responses based on the dst to get to lost.

Fixes: 9d1a6c4ea43e4 ("net: icmp_route_lookup should use rt dev to
		       determine L3 domain")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/route.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/net/ipv4/route.c
+++ b/net/ipv4/route.c
@@ -1902,7 +1902,8 @@ local_input:
 		}
 	}
 
-	rth = rt_dst_alloc(net->loopback_dev, flags | RTCF_LOCAL, res.type,
+	rth = rt_dst_alloc(l3mdev_master_dev_rcu(dev) ? : net->loopback_dev,
+			   flags | RTCF_LOCAL, res.type,
 			   IN_DEV_CONF_GET(in_dev, NOPOLICY), false, do_cache);
 	if (!rth)
 		goto e_nobufs;

[PATCH 4.9 19/59] drop_monitor: add missing call to genlmsg_end

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Reiter Wolfgang <wr0112358@gmail.com>


[ Upstream commit 4200462d88f47f3759bdf4705f87e207b0f5b2e4 ]

Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.

Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/drop_monitor.c |   33 ++++++++++++++++++++++++---------
 1 file changed, 24 insertions(+), 9 deletions(-)

--- a/net/core/drop_monitor.c
+++ b/net/core/drop_monitor.c
@@ -80,6 +80,7 @@ static struct sk_buff *reset_per_cpu_dat
 	struct nlattr *nla;
 	struct sk_buff *skb;
 	unsigned long flags;
+	void *msg_header;
 
 	al = sizeof(struct net_dm_alert_msg);
 	al += dm_hit_limit * sizeof(struct net_dm_drop_point);
@@ -87,17 +88,31 @@ static struct sk_buff *reset_per_cpu_dat
 
 	skb = genlmsg_new(al, GFP_KERNEL);
 
-	if (skb) {
-		genlmsg_put(skb, 0, 0, &net_drop_monitor_family,
-				0, NET_DM_CMD_ALERT);
-		nla = nla_reserve(skb, NLA_UNSPEC,
-				  sizeof(struct net_dm_alert_msg));
-		msg = nla_data(nla);
-		memset(msg, 0, al);
-	} else {
-		mod_timer(&data->send_timer, jiffies + HZ / 10);
+	if (!skb)
+		goto err;
+
+	msg_header = genlmsg_put(skb, 0, 0, &net_drop_monitor_family,
+				 0, NET_DM_CMD_ALERT);
+	if (!msg_header) {
+		nlmsg_free(skb);
+		skb = NULL;
+		goto err;
+	}
+	nla = nla_reserve(skb, NLA_UNSPEC,
+			  sizeof(struct net_dm_alert_msg));
+	if (!nla) {
+		nlmsg_free(skb);
+		skb = NULL;
+		goto err;
 	}
+	msg = nla_data(nla);
+	memset(msg, 0, al);
+	genlmsg_end(skb, msg_header);
+	goto out;
 
+err:
+	mod_timer(&data->send_timer, jiffies + HZ / 10);
+out:
 	spin_lock_irqsave(&data->lock, flags);
 	swap(data->skb, skb);
 	spin_unlock_irqrestore(&data->lock, flags);

[PATCH 4.9 20/59] drop_monitor: consider inserted data in genlmsg_end

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Reiter Wolfgang <wr0112358@gmail.com>


[ Upstream commit 3b48ab2248e61408910e792fe84d6ec466084c1a ]

Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.

This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"

Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/drop_monitor.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

--- a/net/core/drop_monitor.c
+++ b/net/core/drop_monitor.c
@@ -107,7 +107,6 @@ static struct sk_buff *reset_per_cpu_dat
 	}
 	msg = nla_data(nla);
 	memset(msg, 0, al);
-	genlmsg_end(skb, msg_header);
 	goto out;
 
 err:
@@ -117,6 +116,13 @@ out:
 	swap(data->skb, skb);
 	spin_unlock_irqrestore(&data->lock, flags);
 
+	if (skb) {
+		struct nlmsghdr *nlh = (struct nlmsghdr *)skb->data;
+		struct genlmsghdr *gnlh = (struct genlmsghdr *)nlmsg_data(nlh);
+
+		genlmsg_end(skb, genlmsg_data(gnlh));
+	}
+
 	return skb;
 }
 

[PATCH 4.9 21/59] flow_dissector: Update pptp handling to avoid null pointer deref.

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ian Kumlien <ian.kumlien@gmail.com>


[ Upstream commit d0af683407a26a4437d8fa6e283ea201f2ae8146 ]

__skb_flow_dissect can be called with a skb or a data packet, either
can be NULL. All calls seems to have been moved to __skb_header_pointer
except the pptp handling which is still calling skb_header_pointer.

skb_header_pointer will use skb->data and thus:
[  109.556866] BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
[  109.557102] IP: [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[  109.557263] PGD 0
[  109.557338]
[  109.557484] Oops: 0000 [#1] SMP
[  109.557562] Modules linked in: chaoskey
[  109.557783] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.9.0 #79
[  109.557867] Hardware name: Supermicro A1SRM-LN7F/LN5F/A1SRM-LN7F-2758, BIOS 1.0c 11/04/2015
[  109.557957] task: ffff94085c27bc00 task.stack: ffffb745c0068000
[  109.558041] RIP: 0010:[<ffffffff88dc02f8>]  [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[  109.558203] RSP: 0018:ffff94087fc83d40  EFLAGS: 00010206
[  109.558286] RAX: 0000000000000130 RBX: ffffffff8975bf80 RCX: ffff94084fab6800
[  109.558373] RDX: 0000000000000010 RSI: 000000000000000c RDI: 0000000000000000
[  109.558460] RBP: 0000000000000b88 R08: 0000000000000000 R09: 0000000000000022
[  109.558547] R10: 0000000000000008 R11: ffff94087fc83e04 R12: 0000000000000000
[  109.558763] R13: ffff94084fab6800 R14: ffff94087fc83e04 R15: 000000000000002f
[  109.558979] FS:  0000000000000000(0000) GS:ffff94087fc80000(0000) knlGS:0000000000000000
[  109.559326] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  109.559539] CR2: 0000000000000080 CR3: 0000000281809000 CR4: 00000000001026e0
[  109.559753] Stack:
[  109.559957]  000000000000000c ffff94084fab6822 0000000000000001 ffff94085c2b5fc0
[  109.560578]  0000000000000001 0000000000002000 0000000000000000 0000000000000000
[  109.561200]  0000000000000000 0000000000000000 0000000000000000 0000000000000000
[  109.561820] Call Trace:
[  109.562027]  <IRQ>
[  109.562108]  [<ffffffff88dfb4fa>] ? eth_get_headlen+0x7a/0xf0
[  109.562522]  [<ffffffff88c5a35a>] ? igb_poll+0x96a/0xe80
[  109.562737]  [<ffffffff88dc912b>] ? net_rx_action+0x20b/0x350
[  109.562953]  [<ffffffff88546d68>] ? __do_softirq+0xe8/0x280
[  109.563169]  [<ffffffff8854704a>] ? irq_exit+0xaa/0xb0
[  109.563382]  [<ffffffff8847229b>] ? do_IRQ+0x4b/0xc0
[  109.563597]  [<ffffffff8902d4ff>] ? common_interrupt+0x7f/0x7f
[  109.563810]  <EOI>
[  109.563890]  [<ffffffff88d57530>] ? cpuidle_enter_state+0x130/0x2c0
[  109.564304]  [<ffffffff88d57520>] ? cpuidle_enter_state+0x120/0x2c0
[  109.564520]  [<ffffffff8857eacf>] ? cpu_startup_entry+0x19f/0x1f0
[  109.564737]  [<ffffffff8848d55a>] ? start_secondary+0x12a/0x140
[  109.564950] Code: 83 e2 20 a8 80 0f 84 60 01 00 00 c7 04 24 08 00
00 00 66 85 d2 0f 84 be fe ff ff e9 69 fe ff ff 8b 34 24 89 f2 83 c2
04 66 85 c0 <41> 8b 84 24 80 00 00 00 0f 49 d6 41 8d 31 01 d6 41 2b 84
24 84
[  109.569959] RIP  [<ffffffff88dc02f8>] __skb_flow_dissect+0xa88/0xce0
[  109.570245]  RSP <ffff94087fc83d40>
[  109.570453] CR2: 0000000000000080

Fixes: ab10dccb1160 ("rps: Inspect PPTP encapsulated by GRE to get flow hash")
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/flow_dissector.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/net/core/flow_dissector.c
+++ b/net/core/flow_dissector.c
@@ -445,8 +445,9 @@ ip_proto_again:
 			if (hdr->flags & GRE_ACK)
 				offset += sizeof(((struct pptp_gre_header *)0)->ack);
 
-			ppp_hdr = skb_header_pointer(skb, nhoff + offset,
-						     sizeof(_ppp_hdr), _ppp_hdr);
+			ppp_hdr = __skb_header_pointer(skb, nhoff + offset,
+						     sizeof(_ppp_hdr),
+						     data, hlen, _ppp_hdr);
 			if (!ppp_hdr)
 				goto out_bad;
 

[PATCH 4.9 22/59] igmp: Make igmp group member RFC 3376 compliant

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Michal Tesar <mtesar@redhat.com>


[ Upstream commit 7ababb782690e03b78657e27bd051e20163af2d6 ]

5.2. Action on Reception of a Query

 When a system receives a Query, it does not respond immediately.
 Instead, it delays its response by a random amount of time, bounded
 by the Max Resp Time value derived from the Max Resp Code in the
 received Query message.  A system may receive a variety of Queries on
 different interfaces and of different kinds (e.g., General Queries,
 Group-Specific Queries, and Group-and-Source-Specific Queries), each
 of which may require its own delayed response.

 Before scheduling a response to a Query, the system must first
 consider previously scheduled pending responses and in many cases
 schedule a combined response.  Therefore, the system must be able to
 maintain the following state:

 o A timer per interface for scheduling responses to General Queries.

 o A per-group and interface timer for scheduling responses to Group-
   Specific and Group-and-Source-Specific Queries.

 o A per-group and interface list of sources to be reported in the
   response to a Group-and-Source-Specific Query.

 When a new Query with the Router-Alert option arrives on an
 interface, provided the system has state to report, a delay for a
 response is randomly selected in the range (0, [Max Resp Time]) where
 Max Resp Time is derived from Max Resp Code in the received Query
 message.  The following rules are then used to determine if a Report
 needs to be scheduled and the type of Report to schedule.  The rules
 are considered in order and only the first matching rule is applied.

 1. If there is a pending response to a previous General Query
    scheduled sooner than the selected delay, no additional response
    needs to be scheduled.

 2. If the received Query is a General Query, the interface timer is
    used to schedule a response to the General Query after the
    selected delay.  Any previously pending response to a General
    Query is canceled.
--8<--

Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.

Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.

Signed-off-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/igmp.c |    7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

--- a/net/ipv4/igmp.c
+++ b/net/ipv4/igmp.c
@@ -219,9 +219,14 @@ static void igmp_start_timer(struct ip_m
 static void igmp_gq_start_timer(struct in_device *in_dev)
 {
 	int tv = prandom_u32() % in_dev->mr_maxdelay;
+	unsigned long exp = jiffies + tv + 2;
+
+	if (in_dev->mr_gq_running &&
+	    time_after_eq(exp, (in_dev->mr_gq_timer).expires))
+		return;
 
 	in_dev->mr_gq_running = 1;
-	if (!mod_timer(&in_dev->mr_gq_timer, jiffies+tv+2))
+	if (!mod_timer(&in_dev->mr_gq_timer, exp))
 		in_dev_hold(in_dev);
 }
 

[PATCH 4.9 23/59] ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Alexander Duyck <alexander.h.duyck@intel.com>


[ Upstream commit 5350d54f6cd12eaff623e890744c79b700bd3f17 ]

In the case of custom rules being present we need to handle the case of the
LOCAL table being intialized after the new rule has been added.  To address
that I am adding a new check so that we can make certain we don't use an
alias of MAIN for LOCAL when allocating a new table.

Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Oliver Brunel <jjk@jjacky.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/fib_frontend.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/net/ipv4/fib_frontend.c
+++ b/net/ipv4/fib_frontend.c
@@ -85,7 +85,7 @@ struct fib_table *fib_new_table(struct n
 	if (tb)
 		return tb;
 
-	if (id == RT_TABLE_LOCAL)
+	if (id == RT_TABLE_LOCAL && !net->ipv4.fib_has_custom_rules)
 		alias = fib_new_table(net, RT_TABLE_MAIN);
 
 	tb = fib_trie_table(id, alias);

[PATCH 4.9 24/59] net: vrf: Add missing Rx counters

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: David Ahern <dsa@cumulusnetworks.com>


[ Upstream commit 926d93a33e59b2729afdbad357233c17184de9d2 ]

The move from rx-handler to L3 receive handler inadvertantly dropped the
rx counters. Restore them.

Fixes: 74b20582ac38 ("net: l3mdev: Add hook in ip and ipv6")
Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/vrf.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/net/vrf.c
+++ b/drivers/net/vrf.c
@@ -968,6 +968,7 @@ static struct sk_buff *vrf_ip6_rcv(struc
 	 */
 	need_strict = rt6_need_strict(&ipv6_hdr(skb)->daddr);
 	if (!ipv6_ndisc_frame(skb) && !need_strict) {
+		vrf_rx_stats(vrf_dev, skb->len);
 		skb->dev = vrf_dev;
 		skb->skb_iif = vrf_dev->ifindex;
 
@@ -1009,6 +1010,8 @@ static struct sk_buff *vrf_ip_rcv(struct
 		goto out;
 	}
 
+	vrf_rx_stats(vrf_dev, skb->len);
+
 	skb_push(skb, skb->mac_len);
 	dev_queue_xmit_nit(skb, vrf_dev);
 	skb_pull(skb, skb->mac_len);

[PATCH 4.9 25/59] bpf: change back to orig prog on too many passes

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Daniel Borkmann <daniel@iogearbox.net>


[ Upstream commit 9d5ecb09d525469abd1a10c096cb5a17206523f2 ]

If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.

Fixes: 959a75791603 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 arch/x86/net/bpf_jit_comp.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/arch/x86/net/bpf_jit_comp.c
+++ b/arch/x86/net/bpf_jit_comp.c
@@ -1172,6 +1172,8 @@ struct bpf_prog *bpf_int_jit_compile(str
 		set_memory_ro((unsigned long)header, header->pages);
 		prog->bpf_func = (void *)image;
 		prog->jited = 1;
+	} else {
+		prog = orig_prog;
 	}
 
 out_addrs:

[PATCH 4.9 26/59] net: dsa: bcm_sf2: Do not clobber b53_switch_ops

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Florian Fainelli <f.fainelli@gmail.com>


[ Upstream commit a4c61b92b3a4cbda35bb0251a5063a68f0861b2c ]

We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.

Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/dsa/bcm_sf2.c |    7 +++++++
 1 file changed, 7 insertions(+)

--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -982,6 +982,7 @@ static int bcm_sf2_sw_probe(struct platf
 	const char *reg_names[BCM_SF2_REGS_NUM] = BCM_SF2_REGS_NAME;
 	struct device_node *dn = pdev->dev.of_node;
 	struct b53_platform_data *pdata;
+	struct dsa_switch_ops *ops;
 	struct bcm_sf2_priv *priv;
 	struct b53_device *dev;
 	struct dsa_switch *ds;
@@ -995,6 +996,10 @@ static int bcm_sf2_sw_probe(struct platf
 	if (!priv)
 		return -ENOMEM;
 
+	ops = devm_kzalloc(&pdev->dev, sizeof(*ops), GFP_KERNEL);
+	if (!ops)
+		return -ENOMEM;
+
 	dev = b53_switch_alloc(&pdev->dev, &bcm_sf2_io_ops, priv);
 	if (!dev)
 		return -ENOMEM;
@@ -1014,6 +1019,8 @@ static int bcm_sf2_sw_probe(struct platf
 	ds = dev->ds;
 
 	/* Override the parts that are non-standard wrt. normal b53 devices */
+	memcpy(ops, ds->ops, sizeof(*ops));
+	ds->ops = ops;
 	ds->ops->get_tag_protocol = bcm_sf2_sw_get_tag_protocol;
 	ds->ops->setup = bcm_sf2_sw_setup;
 	ds->ops->get_phy_flags = bcm_sf2_sw_get_phy_flags;

[PATCH 4.9 27/59] net: dsa: bcm_sf2: Utilize nested MDIO read/write

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Florian Fainelli <f.fainelli@gmail.com>


[ Upstream commit 2cfe8f8290bd28cf1ee67db914a6e76cf8e6437b ]

We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.

Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/dsa/bcm_sf2.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -393,7 +393,7 @@ static int bcm_sf2_sw_mdio_read(struct m
 	if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr))
 		return bcm_sf2_sw_indir_rw(priv, 1, addr, regnum, 0);
 	else
-		return mdiobus_read(priv->master_mii_bus, addr, regnum);
+		return mdiobus_read_nested(priv->master_mii_bus, addr, regnum);
 }
 
 static int bcm_sf2_sw_mdio_write(struct mii_bus *bus, int addr, int regnum,
@@ -407,7 +407,7 @@ static int bcm_sf2_sw_mdio_write(struct
 	if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr))
 		bcm_sf2_sw_indir_rw(priv, 0, addr, regnum, val);
 	else
-		mdiobus_write(priv->master_mii_bus, addr, regnum, val);
+		mdiobus_write_nested(priv->master_mii_bus, addr, regnum, val);
 
 	return 0;
 }

[PATCH 4.9 28/59] r8152: split rtl8152_suspend function

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: hayeswang <hayeswang@realtek.com>


[ Upstream commit 8fb280616878b81c0790a0c33acbeec59c5711f4 ]

Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/usb/r8152.c |   57 +++++++++++++++++++++++++++++++++---------------
 1 file changed, 40 insertions(+), 17 deletions(-)

--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -3576,39 +3576,62 @@ static bool delay_autosuspend(struct r81
 		return false;
 }
 
-static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
+static int rtl8152_rumtime_suspend(struct r8152 *tp)
 {
-	struct r8152 *tp = usb_get_intfdata(intf);
 	struct net_device *netdev = tp->netdev;
 	int ret = 0;
 
-	mutex_lock(&tp->control);
-
-	if (PMSG_IS_AUTO(message)) {
-		if (netif_running(netdev) && delay_autosuspend(tp)) {
+	if (netif_running(netdev) && test_bit(WORK_ENABLE, &tp->flags)) {
+		if (delay_autosuspend(tp)) {
 			ret = -EBUSY;
 			goto out1;
 		}
 
-		set_bit(SELECTIVE_SUSPEND, &tp->flags);
-	} else {
-		netif_device_detach(netdev);
+		clear_bit(WORK_ENABLE, &tp->flags);
+		usb_kill_urb(tp->intr_urb);
+		napi_disable(&tp->napi);
+		rtl_stop_rx(tp);
+		tp->rtl_ops.autosuspend_en(tp, true);
+		napi_enable(&tp->napi);
 	}
 
+	set_bit(SELECTIVE_SUSPEND, &tp->flags);
+
+out1:
+	return ret;
+}
+
+static int rtl8152_system_suspend(struct r8152 *tp)
+{
+	struct net_device *netdev = tp->netdev;
+	int ret = 0;
+
+	netif_device_detach(netdev);
+
 	if (netif_running(netdev) && test_bit(WORK_ENABLE, &tp->flags)) {
 		clear_bit(WORK_ENABLE, &tp->flags);
 		usb_kill_urb(tp->intr_urb);
 		napi_disable(&tp->napi);
-		if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) {
-			rtl_stop_rx(tp);
-			tp->rtl_ops.autosuspend_en(tp, true);
-		} else {
-			cancel_delayed_work_sync(&tp->schedule);
-			tp->rtl_ops.down(tp);
-		}
+		cancel_delayed_work_sync(&tp->schedule);
+		tp->rtl_ops.down(tp);
 		napi_enable(&tp->napi);
 	}
-out1:
+
+	return ret;
+}
+
+static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct r8152 *tp = usb_get_intfdata(intf);
+	int ret;
+
+	mutex_lock(&tp->control);
+
+	if (PMSG_IS_AUTO(message))
+		ret = rtl8152_rumtime_suspend(tp);
+	else
+		ret = rtl8152_system_suspend(tp);
+
 	mutex_unlock(&tp->control);
 
 	return ret;

[PATCH 4.9 29/59] r8152: fix rx issue for runtime suspend

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: hayeswang <hayeswang@realtek.com>


[ Upstream commit 75dc692eda114cb234a46cb11893a9c3ea520934 ]

Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.

If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/usb/r8152.c |   31 ++++++++++++++++++++++++++++---
 1 file changed, 28 insertions(+), 3 deletions(-)

--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -3582,17 +3582,42 @@ static int rtl8152_rumtime_suspend(struc
 	int ret = 0;
 
 	if (netif_running(netdev) && test_bit(WORK_ENABLE, &tp->flags)) {
+		u32 rcr = 0;
+
 		if (delay_autosuspend(tp)) {
 			ret = -EBUSY;
 			goto out1;
 		}
 
+		if (netif_carrier_ok(netdev)) {
+			u32 ocp_data;
+
+			rcr = ocp_read_dword(tp, MCU_TYPE_PLA, PLA_RCR);
+			ocp_data = rcr & ~RCR_ACPT_ALL;
+			ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, ocp_data);
+			rxdy_gated_en(tp, true);
+			ocp_data = ocp_read_byte(tp, MCU_TYPE_PLA,
+						 PLA_OOB_CTRL);
+			if (!(ocp_data & RXFIFO_EMPTY)) {
+				rxdy_gated_en(tp, false);
+				ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, rcr);
+				ret = -EBUSY;
+				goto out1;
+			}
+		}
+
 		clear_bit(WORK_ENABLE, &tp->flags);
 		usb_kill_urb(tp->intr_urb);
-		napi_disable(&tp->napi);
-		rtl_stop_rx(tp);
+
 		tp->rtl_ops.autosuspend_en(tp, true);
-		napi_enable(&tp->napi);
+
+		if (netif_carrier_ok(netdev)) {
+			napi_disable(&tp->napi);
+			rtl_stop_rx(tp);
+			rxdy_gated_en(tp, false);
+			ocp_write_dword(tp, MCU_TYPE_PLA, PLA_RCR, rcr);
+			napi_enable(&tp->napi);
+		}
 	}
 
 	set_bit(SELECTIVE_SUSPEND, &tp->flags);

[PATCH 4.9 30/59] net: dsa: Ensure validity of dst->ds[0]

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Florian Fainelli <f.fainelli@gmail.com>


[ Upstream commit faf3a932fbeb77860226a8323eacb835edc98648 ]

It is perfectly possible to have non zero indexed switches being present
in a DSA switch tree, in such a case, we will be deferencing a NULL
pointer while dsa_cpu_port_ethtool_{setup,restore}. Be more defensive
and ensure that dst->ds[0] is valid before doing anything with it.

Fixes: 0c73c523cf73 ("net: dsa: Initialize CPU port ethtool ops per tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/dsa/dsa2.c |   11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

--- a/net/dsa/dsa2.c
+++ b/net/dsa/dsa2.c
@@ -394,9 +394,11 @@ static int dsa_dst_apply(struct dsa_swit
 			return err;
 	}
 
-	err = dsa_cpu_port_ethtool_setup(dst->ds[0]);
-	if (err)
-		return err;
+	if (dst->ds[0]) {
+		err = dsa_cpu_port_ethtool_setup(dst->ds[0]);
+		if (err)
+			return err;
+	}
 
 	/* If we use a tagging format that doesn't have an ethertype
 	 * field, make sure that all packets from this point on get
@@ -433,7 +435,8 @@ static void dsa_dst_unapply(struct dsa_s
 		dsa_ds_unapply(dst, ds);
 	}
 
-	dsa_cpu_port_ethtool_restore(dst->ds[0]);
+	if (dst->ds[0])
+		dsa_cpu_port_ethtool_restore(dst->ds[0]);
 
 	pr_info("DSA: tree %d unapplied\n", dst->tree);
 	dst->applied = false;

[PATCH 4.9 31/59] net: add the AF_QIPCRTR entries to family name tables

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: "Anna, Suman" <s-anna@ti.com>


[ Upstream commit 5d722b3024f6762addb8642ffddc9f275b5107ae ]

Commit bdabad3e363d ("net: Add Qualcomm IPC router") introduced a
new address family. Update the family name tables accordingly so
that the lockdep initialization can use the proper names for this
family.

Cc: Courtney Cavin <courtney.cavin@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/sock.c |    6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

--- a/net/core/sock.c
+++ b/net/core/sock.c
@@ -222,7 +222,7 @@ static const char *const af_family_key_s
   "sk_lock-AF_RXRPC" , "sk_lock-AF_ISDN"     , "sk_lock-AF_PHONET"   ,
   "sk_lock-AF_IEEE802154", "sk_lock-AF_CAIF" , "sk_lock-AF_ALG"      ,
   "sk_lock-AF_NFC"   , "sk_lock-AF_VSOCK"    , "sk_lock-AF_KCM"      ,
-  "sk_lock-AF_MAX"
+  "sk_lock-AF_QIPCRTR", "sk_lock-AF_MAX"
 };
 static const char *const af_family_slock_key_strings[AF_MAX+1] = {
   "slock-AF_UNSPEC", "slock-AF_UNIX"     , "slock-AF_INET"     ,
@@ -239,7 +239,7 @@ static const char *const af_family_slock
   "slock-AF_RXRPC" , "slock-AF_ISDN"     , "slock-AF_PHONET"   ,
   "slock-AF_IEEE802154", "slock-AF_CAIF" , "slock-AF_ALG"      ,
   "slock-AF_NFC"   , "slock-AF_VSOCK"    ,"slock-AF_KCM"       ,
-  "slock-AF_MAX"
+  "slock-AF_QIPCRTR", "slock-AF_MAX"
 };
 static const char *const af_family_clock_key_strings[AF_MAX+1] = {
   "clock-AF_UNSPEC", "clock-AF_UNIX"     , "clock-AF_INET"     ,
@@ -256,7 +256,7 @@ static const char *const af_family_clock
   "clock-AF_RXRPC" , "clock-AF_ISDN"     , "clock-AF_PHONET"   ,
   "clock-AF_IEEE802154", "clock-AF_CAIF" , "clock-AF_ALG"      ,
   "clock-AF_NFC"   , "clock-AF_VSOCK"    , "clock-AF_KCM"      ,
-  "clock-AF_MAX"
+  "clock-AF_QIPCRTR", "clock-AF_MAX"
 };
 
 /*

[PATCH 4.9 32/59] gro: Enter slow-path if there is no tailroom

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Herbert Xu <herbert@gondor.apana.org.au>


[ Upstream commit 1272ce87fa017ca4cf32920764d879656b7a005a ]

The GRO path has a fast-path where we avoid calling pskb_may_pull
and pskb_expand by directly accessing frag0.  However, this should
only be done if we have enough tailroom in the skb as otherwise
we'll have to expand it later anyway.

This patch adds the check by capping frag0_len with the skb tailroom.

Fixes: cb18978cbf45 ("gro: Open-code final pskb_may_pull")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/dev.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -4453,7 +4453,8 @@ static void skb_gro_reset_offset(struct
 	    pinfo->nr_frags &&
 	    !PageHighMem(skb_frag_page(frag0))) {
 		NAPI_GRO_CB(skb)->frag0 = skb_frag_address(frag0);
-		NAPI_GRO_CB(skb)->frag0_len = skb_frag_size(frag0);
+		NAPI_GRO_CB(skb)->frag0_len = min(skb_frag_size(frag0),
+						  skb->end - skb->tail);
 	}
 }
 

[PATCH 4.9 33/59] gro: use min_t() in skb_gro_reset_offset()

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Eric Dumazet <edumazet@google.com>


[ Upstream commit 7cfd5fd5a9813f1430290d20c0fead9b4582a307 ]

On 32bit arches, (skb->end - skb->data) is not 'unsigned int',
so we shall use min_t() instead of min() to avoid a compiler error.

Fixes: 1272ce87fa01 ("gro: Enter slow-path if there is no tailroom")
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/dev.c |    5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -4453,8 +4453,9 @@ static void skb_gro_reset_offset(struct
 	    pinfo->nr_frags &&
 	    !PageHighMem(skb_frag_page(frag0))) {
 		NAPI_GRO_CB(skb)->frag0 = skb_frag_address(frag0);
-		NAPI_GRO_CB(skb)->frag0_len = min(skb_frag_size(frag0),
-						  skb->end - skb->tail);
+		NAPI_GRO_CB(skb)->frag0_len = min_t(unsigned int,
+						    skb_frag_size(frag0),
+						    skb->end - skb->tail);
 	}
 }
 

[PATCH 4.9 34/59] gro: Disable frag0 optimization on IPv6 ext headers

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Herbert Xu <herbert@gondor.apana.org.au>


[ Upstream commit 57ea52a865144aedbcd619ee0081155e658b6f7d ]

The GRO fast path caches the frag0 address.  This address becomes
invalid if frag0 is modified by pskb_may_pull or its variants.
So whenever that happens we must disable the frag0 optimization.

This is usually done through the combination of gro_header_hard
and gro_header_slow, however, the IPv6 extension header path did
the pulling directly and would continue to use the GRO fast path
incorrectly.

This patch fixes it by disabling the fast path when we enter the
IPv6 extension header path.

Fixes: 78a478d0efd9 ("gro: Inline skb_gro_header and cache frag0 virtual address")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 include/linux/netdevice.h |    9 +++++++--
 net/ipv6/ip6_offload.c    |    1 +
 2 files changed, 8 insertions(+), 2 deletions(-)

--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -2502,14 +2502,19 @@ static inline int skb_gro_header_hard(st
 	return NAPI_GRO_CB(skb)->frag0_len < hlen;
 }
 
+static inline void skb_gro_frag0_invalidate(struct sk_buff *skb)
+{
+	NAPI_GRO_CB(skb)->frag0 = NULL;
+	NAPI_GRO_CB(skb)->frag0_len = 0;
+}
+
 static inline void *skb_gro_header_slow(struct sk_buff *skb, unsigned int hlen,
 					unsigned int offset)
 {
 	if (!pskb_may_pull(skb, hlen))
 		return NULL;
 
-	NAPI_GRO_CB(skb)->frag0 = NULL;
-	NAPI_GRO_CB(skb)->frag0_len = 0;
+	skb_gro_frag0_invalidate(skb);
 	return skb->data + offset;
 }
 
--- a/net/ipv6/ip6_offload.c
+++ b/net/ipv6/ip6_offload.c
@@ -191,6 +191,7 @@ static struct sk_buff **ipv6_gro_receive
 	ops = rcu_dereference(inet6_offloads[proto]);
 	if (!ops || !ops->callbacks.gro_receive) {
 		__pskb_pull(skb, skb_gro_offset(skb));
+		skb_gro_frag0_invalidate(skb);
 		proto = ipv6_gso_pull_exthdrs(skb, proto);
 		skb_gro_pull(skb, -skb_transport_offset(skb));
 		skb_reset_transport_header(skb);

[PATCH 4.9 35/59] net/mlx5e: Remove WARN_ONCE from adaptive moderation code

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Gil Rockah <gilr@mellanox.com>


[ Upstream commit 0bbcc0a8fc394d01988fe0263ccf7fddb77a12c3 ]

When trying to do interface down or changing interface configuration
under heavy traffic, some of the adaptive moderation corner cases can
occur and leave a WARN_ONCE call trace in the kernel log.

Those WARN_ONCE are meant for debug only, and should have been inserted
only under debug. We avoid such call traces by removing those WARN_ONCE.

Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx5/core/en_rx_am.c |    7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

--- a/drivers/net/ethernet/mellanox/mlx5/core/en_rx_am.c
+++ b/drivers/net/ethernet/mellanox/mlx5/core/en_rx_am.c
@@ -109,7 +109,6 @@ static bool mlx5e_am_on_top(struct mlx5e
 	switch (am->tune_state) {
 	case MLX5E_AM_PARKING_ON_TOP:
 	case MLX5E_AM_PARKING_TIRED:
-		WARN_ONCE(true, "mlx5e_am_on_top: PARKING\n");
 		return true;
 	case MLX5E_AM_GOING_RIGHT:
 		return (am->steps_left > 1) && (am->steps_right == 1);
@@ -123,7 +122,6 @@ static void mlx5e_am_turn(struct mlx5e_r
 	switch (am->tune_state) {
 	case MLX5E_AM_PARKING_ON_TOP:
 	case MLX5E_AM_PARKING_TIRED:
-		WARN_ONCE(true, "mlx5e_am_turn: PARKING\n");
 		break;
 	case MLX5E_AM_GOING_RIGHT:
 		am->tune_state = MLX5E_AM_GOING_LEFT;
@@ -144,7 +142,6 @@ static int mlx5e_am_step(struct mlx5e_rx
 	switch (am->tune_state) {
 	case MLX5E_AM_PARKING_ON_TOP:
 	case MLX5E_AM_PARKING_TIRED:
-		WARN_ONCE(true, "mlx5e_am_step: PARKING\n");
 		break;
 	case MLX5E_AM_GOING_RIGHT:
 		if (am->profile_ix == (MLX5E_PARAMS_AM_NUM_PROFILES - 1))
@@ -282,10 +279,8 @@ static void mlx5e_am_calc_stats(struct m
 	u32 delta_us = ktime_us_delta(end->time, start->time);
 	unsigned int npkts = end->pkt_ctr - start->pkt_ctr;
 
-	if (!delta_us) {
-		WARN_ONCE(true, "mlx5e_am_calc_stats: delta_us=0\n");
+	if (!delta_us)
 		return;
-	}
 
 	curr_stats->ppms =            (npkts * USEC_PER_MSEC) / delta_us;
 	curr_stats->epms = (MLX5E_AM_NEVENTS * USEC_PER_MSEC) / delta_us;

[PATCH 4.9 36/59] net: ipv4: Fix multipath selection with vrf

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: David Ahern <dsa@cumulusnetworks.com>


[ Upstream commit 7a18c5b9fb31a999afc62b0e60978aa896fc89e9 ]

fib_select_path does not call fib_select_multipath if oif is set in the
flow struct. For VRF use cases oif is always set, so multipath route
selection is bypassed. Use the FLOWI_FLAG_SKIP_NH_OIF to skip the oif
check similar to what is done in fib_table_lookup.

Add saddr and proto to the flow struct for the fib lookup done by the
VRF driver to better match hash computation for a flow.

Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/vrf.c        |    2 ++
 net/ipv4/fib_semantics.c |    9 +++++++--
 2 files changed, 9 insertions(+), 2 deletions(-)

--- a/drivers/net/vrf.c
+++ b/drivers/net/vrf.c
@@ -263,7 +263,9 @@ static netdev_tx_t vrf_process_v4_outbou
 		.flowi4_iif = LOOPBACK_IFINDEX,
 		.flowi4_tos = RT_TOS(ip4h->tos),
 		.flowi4_flags = FLOWI_FLAG_ANYSRC | FLOWI_FLAG_SKIP_NH_OIF,
+		.flowi4_proto = ip4h->protocol,
 		.daddr = ip4h->daddr,
+		.saddr = ip4h->saddr,
 	};
 	struct net *net = dev_net(vrf_dev);
 	struct rtable *rt;
--- a/net/ipv4/fib_semantics.c
+++ b/net/ipv4/fib_semantics.c
@@ -1617,8 +1617,13 @@ void fib_select_multipath(struct fib_res
 void fib_select_path(struct net *net, struct fib_result *res,
 		     struct flowi4 *fl4, int mp_hash)
 {
+	bool oif_check;
+
+	oif_check = (fl4->flowi4_oif == 0 ||
+		     fl4->flowi4_flags & FLOWI_FLAG_SKIP_NH_OIF);
+
 #ifdef CONFIG_IP_ROUTE_MULTIPATH
-	if (res->fi->fib_nhs > 1 && fl4->flowi4_oif == 0) {
+	if (res->fi->fib_nhs > 1 && oif_check) {
 		if (mp_hash < 0)
 			mp_hash = get_hash_from_flowi4(fl4) >> 1;
 
@@ -1628,7 +1633,7 @@ void fib_select_path(struct net *net, st
 #endif
 	if (!res->prefixlen &&
 	    res->table->tb_num_default > 1 &&
-	    res->type == RTN_UNICAST && !fl4->flowi4_oif)
+	    res->type == RTN_UNICAST && oif_check)
 		fib_select_default(fl4, res);
 
 	if (!fl4->saddr)

[PATCH 4.9 37/59] net: vrf: do not allow table id 0

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: David Ahern <dsa@cumulusnetworks.com>


[ Upstream commit 24c63bbc18e25d5d8439422aa5fd2d66390b88eb ]

Frank reported that vrf devices can be created with a table id of 0.
This breaks many of the run time table id checks and should not be
allowed. Detect this condition at create time and fail with EINVAL.

Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Frank Kellermann <frank.kellermann@atos.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/vrf.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/net/vrf.c
+++ b/drivers/net/vrf.c
@@ -1239,6 +1239,8 @@ static int vrf_newlink(struct net *src_n
 		return -EINVAL;
 
 	vrf->tb_id = nla_get_u32(data[IFLA_VRF_TABLE]);
+	if (vrf->tb_id == RT_TABLE_UNSPEC)
+		return -EINVAL;
 
 	dev->priv_flags |= IFF_L3MDEV_MASTER;
 

[PATCH 4.9 38/59] HID: hid-cypress: validate length of report

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1ebb71143758f45dc0fa76e2f48429e13b16d110 upstream.

Make sure we have enough of a report structure to validate before
looking at it.

Reported-by: Benoit Camredon <benoit.camredon@airbus.com>
Tested-by: Benoit Camredon <benoit.camredon@airbus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

---
 drivers/hid/hid-cypress.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/hid/hid-cypress.c
+++ b/drivers/hid/hid-cypress.c
@@ -39,6 +39,9 @@ static __u8 *cp_report_fixup(struct hid_
 	if (!(quirks & CP_RDESC_SWAPPED_MIN_MAX))
 		return rdesc;
 
+	if (*rsize < 4)
+		return rdesc;
+
 	for (i = 0; i < *rsize - 4; i++)
 		if (rdesc[i] == 0x29 && rdesc[i + 2] == 0x19) {
 			rdesc[i] = 0x19;

[PATCH 4.9 39/59] ALSA: firewire-tascam: Fix to handle error from initialization of stream data

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Takashi Sakamoto <o-takashi@sakamocchi.jp>

commit 6a2a2f45560a9cb7bc49820883b042e44f83726c upstream.

This module has a bug not to return error code in a case that data
structure for transmitted packets fails to be initialized.

This commit fixes the bug.

Fixes: 35efa5c489de ("ALSA: firewire-tascam: add streaming functionality")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/firewire/tascam/tascam-stream.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/sound/firewire/tascam/tascam-stream.c
+++ b/sound/firewire/tascam/tascam-stream.c
@@ -343,7 +343,7 @@ int snd_tscm_stream_init_duplex(struct s
 	if (err < 0)
 		amdtp_stream_destroy(&tscm->rx_stream);
 
-	return 0;
+	return err;
 }
 
 /* At bus reset, streaming is stopped and some registers are clear. */

[PATCH 4.9 40/59] powerpc: Fix build warning on 32-bit PPC

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Larry Finger <Larry.Finger@lwfinger.net>

commit 8ae679c4bc2ea2d16d92620da8e3e9332fa4039f upstream.

I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:

    AS      arch/powerpc/kernel/misc_32.o
  arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]

This problem is evident after commit 989cea5c14be ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created.  That was with commit 9994a33865f4 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").

The offending line does not make a lot of sense.  This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.

Thanks to Nicholas Piggin for suggesting this solution.

Fixes: 9994a33865f4 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/powerpc/kernel/misc_32.S |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/powerpc/kernel/misc_32.S
+++ b/arch/powerpc/kernel/misc_32.S
@@ -296,7 +296,7 @@ _GLOBAL(flush_instruction_cache)
 	lis	r3, KERNELBASE@h
 	iccci	0,r3
 #endif
-#elif CONFIG_FSL_BOOKE
+#elif defined(CONFIG_FSL_BOOKE)
 BEGIN_FTR_SECTION
 	mfspr   r3,SPRN_L1CSR0
 	ori     r3,r3,L1CSR0_CFI|L1CSR0_CLFC

[PATCH 4.9 41/59] tools/virtio: fix READ_ONCE()

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Mark Rutland <mark.rutland@arm.com>

commit 5da889c795b1fbefc9d8f058b54717ab8ab17891 upstream.

The virtio tools implementation of READ_ONCE() has a single parameter called
'var', but erroneously refers to 'val' for its cast, and thus won't work unless
there's a variable of the correct type that happens to be called 'var'.

Fix this with s/var/val/, making READ_ONCE() work as expected regardless.

Fixes: a7c490333df3cff5 ("tools/virtio: use virt_xxx barriers")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 tools/virtio/linux/compiler.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/tools/virtio/linux/compiler.h
+++ b/tools/virtio/linux/compiler.h
@@ -4,6 +4,6 @@
 #define WRITE_ONCE(var, val) \
 	(*((volatile typeof(val) *)(&(var))) = (val))
 
-#define READ_ONCE(var) (*((volatile typeof(val) *)(&(var))))
+#define READ_ONCE(var) (*((volatile typeof(var) *)(&(var))))
 
 #endif

[PATCH 4.9 42/59] arm64: dts: mt8173: Fix auxadc node

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Matthias Brugger <matthias.bgg@gmail.com>

commit a3207d644fb89e5d7d5e01f00c04dcfc6d2d44d5 upstream.

The devicetree node for mt8173-auxadc lacks the clock and
io-channel-cells property. This leads to a non-working driver.

	mt6577-auxadc 11001000.auxadc: failed to get auxadc clock
	mt6577-auxadc: probe of 11001000.auxadc failed with error -2

Fix these fields to get the device up and running.

Fixes: 748c7d4de46a ("ARM64: dts: mt8173: Add thermal/auxadc device
nodes")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm64/boot/dts/mediatek/mt8173.dtsi |    3 +++
 1 file changed, 3 insertions(+)

--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -450,6 +450,9 @@
 		auxadc: auxadc@11001000 {
 			compatible = "mediatek,mt8173-auxadc";
 			reg = <0 0x11001000 0 0x1000>;
+			clocks = <&pericfg CLK_PERI_AUXADC>;
+			clock-names = "main";
+			#io-channel-cells = <1>;
 		};
 
 		uart0: serial@11002000 {

[PATCH 4.9 43/59] ARM64: dts: bcm2837-rpi-3-b: remove incorrect pwr LED

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Andrea Merello <andrea.merello@gmail.com>

commit a44e87b47148c6ee6b78509f47e6a15c0fae890a upstream.

We are incorrectly defining the pwr LED, attaching it to a gpio line
that is wired to the Wi-Fi SDIO module (which fails due to this).

The actual power LED is connected to the GPIO expander, which we don't
expose currently.

Fixes: 9d56c22a7861 ("ARM: bcm2835: Add devicetree for the Raspberry Pi 3.")
Thanks-to: Eric Anholt <eric@anholt.net> [for clarifying we can't control the LED]
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts |    7 -------
 1 file changed, 7 deletions(-)

--- a/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts
+++ b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-b.dts
@@ -15,13 +15,6 @@
 		act {
 			gpios = <&gpio 47 0>;
 		};
-
-		pwr {
-			label = "PWR";
-			gpios = <&gpio 35 0>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
 	};
 };
 

[PATCH 4.9 45/59] ARM: pxa: fix pxa25x interrupt init

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Robert Jarzmik <robert.jarzmik@free.fr>

commit e413bd33ac44b6d0bebc0ef2ac19cbe7558a7303 upstream.

In the device-tree case, the root interrupt controller cannot be
accessed through the 6th coprocessor, contrary to pxa27x and pxa3xx
architectures.

Fix it to behave as in non-devicetree builds.

Fixes: 32f17997c130 ("ARM: pxa: remove irq init from dt machines")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-pxa/pxa25x.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -156,7 +156,7 @@ static int __init __init
 pxa25x_dt_init_irq(struct device_node *node, struct device_node *parent)
 {
 	pxa_dt_irq_init(pxa25x_set_wake);
-	set_handle_irq(ichp_handle_irq);
+	set_handle_irq(icip_handle_irq);
 
 	return 0;
 }

[PATCH 4.9 46/59] ARM: zynq: Reserve correct amount of non-DMA RAM

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Kyle Roeschley <kyle.roeschley@ni.com>

commit 7a3cc2a7b2c723aa552028f4e66841cec183756d upstream.

On Zynq, we haven't been reserving the correct amount of DMA-incapable
RAM to keep DMA away from it (per the Zynq TRM Section 4.1, it should be
the first 512k). In older kernels, this was masked by the
memblock_reserve call in arm_memblock_init(). Now, reserve the correct
amount excplicitly rather than relying on swapper_pg_dir, which is an
address and not a size anyway.

Fixes: 46f5b96 ("ARM: zynq: Reserve not DMAable space in front of the kernel")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Tested-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-zynq/common.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/arm/mach-zynq/common.c
+++ b/arch/arm/mach-zynq/common.c
@@ -59,7 +59,7 @@ void __iomem *zynq_scu_base;
 static void __init zynq_memory_init(void)
 {
 	if (!__pa(PAGE_OFFSET))
-		memblock_reserve(__pa(PAGE_OFFSET), __pa(swapper_pg_dir));
+		memblock_reserve(__pa(PAGE_OFFSET), 0x80000);
 }
 
 static struct platform_device zynq_cpuidle_device = {

[PATCH 4.9 47/59] ARM: qcom_defconfig: Fix MDM9515 LCC and GCC config

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Neil Armstrong <narmstrong@baylibre.com>

commit 206787737e308bb447d18adef7da7749188212f5 upstream.

Correct prefix is MDM instead of MSM.

Fixes: 8aa788d3e59a ("ARM: configs: qualcomm: Add MDM9615 missing defconfigs")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/configs/qcom_defconfig |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -162,8 +162,8 @@ CONFIG_APQ_MMCC_8084=y
 CONFIG_IPQ_LCC_806X=y
 CONFIG_MSM_GCC_8660=y
 CONFIG_MSM_LCC_8960=y
-CONFIG_MSM_GCC_9615=y
-CONFIG_MSM_LCC_9615=y
+CONFIG_MDM_GCC_9615=y
+CONFIG_MDM_LCC_9615=y
 CONFIG_MSM_MMCC_8960=y
 CONFIG_MSM_MMCC_8974=y
 CONFIG_HWSPINLOCK_QCOM=y

[PATCH 4.9 48/59] svcrdma: Clear xpt_bc_xps in xprt_setup_rdma_bc() error exit arm

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Chuck Lever <chuck.lever@oracle.com>

commit 1b9f700b8cfc31089e2dfa5d0905c52fd4529b50 upstream.

Logic copied from xs_setup_bc_tcp().

Fixes: 39a9beab5acb ('rpc: share one xps between all backchannels')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 net/sunrpc/xprtrdma/svc_rdma_backchannel.c |    1 +
 1 file changed, 1 insertion(+)

--- a/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
+++ b/net/sunrpc/xprtrdma/svc_rdma_backchannel.c
@@ -359,6 +359,7 @@ xprt_setup_rdma_bc(struct xprt_create *a
 out_fail:
 	xprt_rdma_free_addresses(xprt);
 	args->bc_xprt->xpt_bc_xprt = NULL;
+	args->bc_xprt->xpt_bc_xps = NULL;
 	xprt_put(xprt);
 	xprt_free(xprt);
 	return ERR_PTR(-EINVAL);

[PATCH 4.9 49/59] bus: arm-ccn: Prevent hotplug callback leak

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Thomas Gleixner <tglx@linutronix.de>

commit 26242b330093fd14c2e94fb6cbdf0f482ab26576 upstream.

In case the driver registration fails, the hotplug callback is leaked.

Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.

Fixes: fdc15a36d84e ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/bus/arm-ccn.c |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

--- a/drivers/bus/arm-ccn.c
+++ b/drivers/bus/arm-ccn.c
@@ -1570,7 +1570,10 @@ static int __init arm_ccn_init(void)
 	for (i = 0; i < ARRAY_SIZE(arm_ccn_pmu_events); i++)
 		arm_ccn_pmu_events_attrs[i] = &arm_ccn_pmu_events[i].attr.attr;
 
-	return platform_driver_register(&arm_ccn_driver);
+	ret = platform_driver_register(&arm_ccn_driver);
+	if (ret)
+		cpuhp_remove_multi_state(CPUHP_AP_PERF_ARM_CCN_ONLINE);
+	return ret;
 }
 
 static void __exit arm_ccn_exit(void)

[PATCH 4.9 50/59] ARM: OMAP5: Fix mpuss_early_init

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Tony Lindgren <tony@atomide.com>

commit 8a8be46afeaa47aed1debe7e9b18152f9826a6b7 upstream.

We need to properly initialize mpuss also on omap5 like we do on omap4.
Otherwise we run into similar kexec problems like we had on omap4 when
trying to kexec from a kernel with PM initialized.

Fixes: 0573b957fc21 ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-omap2/common.h              |   38 ++++++++++++++++++++++--------
 arch/arm/mach-omap2/io.c                  |    3 +-
 arch/arm/mach-omap2/omap-mpuss-lowpower.c |   32 +++++++++++++++++++------
 arch/arm/mach-omap2/omap4-sar-layout.h    |    2 +
 4 files changed, 58 insertions(+), 17 deletions(-)

--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -262,8 +262,6 @@ extern void __iomem *omap4_get_sar_ram_b
 extern void omap4_mpuss_early_init(void);
 extern void omap_do_wfi(void);
 
-extern void omap4_secondary_startup(void);
-extern void omap4460_secondary_startup(void);
 
 #ifdef CONFIG_SMP
 /* Needed for secondary core boot */
@@ -275,16 +273,11 @@ extern void omap4_cpu_die(unsigned int c
 extern int omap4_cpu_kill(unsigned int cpu);
 
 extern const struct smp_operations omap4_smp_ops;
-
-extern void omap5_secondary_startup(void);
-extern void omap5_secondary_hyp_startup(void);
 #endif
 
 #if defined(CONFIG_SMP) && defined(CONFIG_PM)
 extern int omap4_mpuss_init(void);
 extern int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state);
-extern int omap4_finish_suspend(unsigned long cpu_state);
-extern void omap4_cpu_resume(void);
 extern int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state);
 #else
 static inline int omap4_enter_lowpower(unsigned int cpu,
@@ -305,14 +298,41 @@ static inline int omap4_mpuss_init(void)
 	return 0;
 }
 
+#endif
+
+#ifdef CONFIG_ARCH_OMAP4
+void omap4_secondary_startup(void);
+void omap4460_secondary_startup(void);
+int omap4_finish_suspend(unsigned long cpu_state);
+void omap4_cpu_resume(void);
+#else
+static inline void omap4_secondary_startup(void)
+{
+}
+
+static inline void omap4460_secondary_startup(void)
+{
+}
 static inline int omap4_finish_suspend(unsigned long cpu_state)
 {
 	return 0;
 }
-
 static inline void omap4_cpu_resume(void)
-{}
+{
+}
+#endif
 
+#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX)
+void omap5_secondary_startup(void);
+void omap5_secondary_hyp_startup(void);
+#else
+static inline void omap5_secondary_startup(void)
+{
+}
+
+static inline void omap5_secondary_hyp_startup(void)
+{
+}
 #endif
 
 void pdata_quirks_init(const struct of_device_id *);
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -717,10 +717,11 @@ void __init omap5_init_early(void)
 			      OMAP2_L4_IO_ADDRESS(OMAP54XX_SCM_BASE));
 	omap2_set_globals_prcm_mpu(OMAP2_L4_IO_ADDRESS(OMAP54XX_PRCM_MPU_BASE));
 	omap2_control_base_init();
-	omap4_pm_init_early();
 	omap2_prcm_base_init();
 	omap5xxx_check_revision();
 	omap4_sar_ram_init();
+	omap4_mpuss_early_init();
+	omap4_pm_init_early();
 	omap54xx_voltagedomains_init();
 	omap54xx_powerdomains_init();
 	omap54xx_clockdomains_init();
--- a/arch/arm/mach-omap2/omap-mpuss-lowpower.c
+++ b/arch/arm/mach-omap2/omap-mpuss-lowpower.c
@@ -48,6 +48,7 @@
 #include <asm/smp_scu.h>
 #include <asm/pgalloc.h>
 #include <asm/suspend.h>
+#include <asm/virt.h>
 #include <asm/hardware/cache-l2x0.h>
 
 #include "soc.h"
@@ -371,8 +372,12 @@ int __init omap4_mpuss_init(void)
 	pm_info = &per_cpu(omap4_pm_info, 0x0);
 	if (sar_base) {
 		pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
-		pm_info->wkup_sar_addr = sar_base +
-					CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
+		if (cpu_is_omap44xx())
+			pm_info->wkup_sar_addr = sar_base +
+				CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
+		else
+			pm_info->wkup_sar_addr = sar_base +
+				OMAP5_CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
 		pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
 	}
 	pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
@@ -391,8 +396,12 @@ int __init omap4_mpuss_init(void)
 	pm_info = &per_cpu(omap4_pm_info, 0x1);
 	if (sar_base) {
 		pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
-		pm_info->wkup_sar_addr = sar_base +
-					CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
+		if (cpu_is_omap44xx())
+			pm_info->wkup_sar_addr = sar_base +
+				CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
+		else
+			pm_info->wkup_sar_addr = sar_base +
+				OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
 		pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
 	}
 
@@ -453,15 +462,24 @@ void __init omap4_mpuss_early_init(void)
 {
 	unsigned long startup_pa;
 
-	if (!cpu_is_omap44xx())
+	if (!(cpu_is_omap44xx() || soc_is_omap54xx()))
 		return;
 
 	sar_base = omap4_get_sar_ram_base();
 
 	if (cpu_is_omap443x())
 		startup_pa = virt_to_phys(omap4_secondary_startup);
-	else
+	else if (cpu_is_omap446x())
 		startup_pa = virt_to_phys(omap4460_secondary_startup);
+	else if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
+		startup_pa = virt_to_phys(omap5_secondary_hyp_startup);
+	else
+		startup_pa = virt_to_phys(omap5_secondary_startup);
 
-	writel_relaxed(startup_pa, sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
+	if (cpu_is_omap44xx())
+		writel_relaxed(startup_pa, sar_base +
+			       CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
+	else
+		writel_relaxed(startup_pa, sar_base +
+			       OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
 }
--- a/arch/arm/mach-omap2/omap4-sar-layout.h
+++ b/arch/arm/mach-omap2/omap4-sar-layout.h
@@ -31,6 +31,8 @@
 /* CPUx Wakeup Non-Secure Physical Address offsets in SAR_BANK3 */
 #define CPU0_WAKEUP_NS_PA_ADDR_OFFSET		0xa04
 #define CPU1_WAKEUP_NS_PA_ADDR_OFFSET		0xa08
+#define OMAP5_CPU0_WAKEUP_NS_PA_ADDR_OFFSET	0xe00
+#define OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET	0xe04
 
 #define SAR_BACKUP_STATUS_OFFSET		(SAR_BANK3_OFFSET + 0x500)
 #define SAR_SECURE_RAM_SIZE_OFFSET		(SAR_BANK3_OFFSET + 0x504)

[PATCH 4.9 51/59] ARM: OMAP5: Fix build for PM code

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Tony Lindgren <tony@atomide.com>

commit da6d5993bf951846956903bee4f0eafd918250db upstream.

It's CONFIG_SOC_OMAP5, not CONFIG_ARCH_OMAP5. Looks like make randconfig
builds have not hit this one yet.

Fixes: b3bf289c1c45 ("ARM: OMAP2+: Fix build with CONFIG_SMP and CONFIG_PM is not set")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-omap2/Makefile |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -80,7 +80,7 @@ endif
 # Power Management
 omap-4-5-pm-common			= omap-mpuss-lowpower.o
 obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-4-5-pm-common)
-obj-$(CONFIG_ARCH_OMAP5)		+= $(omap-4-5-pm-common)
+obj-$(CONFIG_SOC_OMAP5)			+= $(omap-4-5-pm-common)
 obj-$(CONFIG_OMAP_PM_NOOP)		+= omap-pm-noop.o
 
 ifeq ($(CONFIG_PM),y)

[PATCH 4.9 52/59] ARM: OMAP4+: Fix bad fallthrough for cpuidle

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Tony Lindgren <tony@atomide.com>

commit cbf2642872333547b56b8c4d943f5ed04ac9a4ee upstream.

We don't want to fall through to a bunch of errors for retention
if PM_OMAP4_CPU_OSWR_DISABLE is not configured for a SoC.

Fixes: 6099dd37c669 ("ARM: OMAP5 / DRA7: Enable CPU RET on suspend")
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-omap2/omap-mpuss-lowpower.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

--- a/arch/arm/mach-omap2/omap-mpuss-lowpower.c
+++ b/arch/arm/mach-omap2/omap-mpuss-lowpower.c
@@ -245,10 +245,9 @@ int omap4_enter_lowpower(unsigned int cp
 		save_state = 1;
 		break;
 	case PWRDM_POWER_RET:
-		if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE)) {
+		if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE))
 			save_state = 0;
-			break;
-		}
+		break;
 	default:
 		/*
 		 * CPUx CSWR is invalid hardware state. Also CPUx OSWR

[PATCH 4.9 53/59] ARM: 8631/1: clkdev: Detect errors in clk_hw_register_clkdev() for mass registration

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Geert Uytterhoeven <geert@linux-m68k.org>

commit 9388093db44356af911adf3d355b7544a13a63cd upstream.

Unlike clk_register_clkdev(), clk_hw_register_clkdev() doesn't check for
passed error objects from a previous registration call. Hence the caller
of clk_hw_register_*() has to check for errors before calling
clk_hw_register_clkdev*().

Make clk_hw_register_clkdev() more similar to clk_register_clkdev() by
adding this error check, removing the burden from callers that do mass
registration.

Fixes: e4f1b49bda6d6aa2 ("clkdev: Add clk_hw based registration APIs")
Fixes: 944b9a41e004534f ("clk: ls1x: Migrate to clk_hw based OF and registration APIs")
Fixes: 44ce9a9ae977736f ("MIPS: TXx9: Convert to Common Clock Framework")
Fixes: f48d947a162dfa9d ("clk: clps711x: Migrate to clk_hw based OF and registration APIs")
Fixes: b4626a7f489238a5 ("CLK: Add Loongson1C clock support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/clk/clkdev.c |    8 ++++++++
 1 file changed, 8 insertions(+)

--- a/drivers/clk/clkdev.c
+++ b/drivers/clk/clkdev.c
@@ -448,12 +448,20 @@ EXPORT_SYMBOL(clk_register_clkdev);
  *
  * con_id or dev_id may be NULL as a wildcard, just as in the rest of
  * clkdev.
+ *
+ * To make things easier for mass registration, we detect error clk_hws
+ * from a previous clk_hw_register_*() call, and return the error code for
+ * those.  This is to permit this function to be called immediately
+ * after clk_hw_register_*().
  */
 int clk_hw_register_clkdev(struct clk_hw *hw, const char *con_id,
 	const char *dev_id)
 {
 	struct clk_lookup *cl;
 
+	if (IS_ERR(hw))
+		return PTR_ERR(hw);
+
 	/*
 	 * Since dev_id can be NULL, and NULL is handled specially, we must
 	 * pass it as either a NULL format string, or with "%s".

[PATCH 4.9 54/59] ARM: omap2+: am437x: rollback to use omap3_gptimer_timer_init()

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Grygorii Strashko <grygorii.strashko@ti.com>

commit f86a2c875fd146d9b82c8fdd86d31084507bcf4c upstream.

The commit 55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.

Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit 5b5c01359152 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).

Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().

[1] http://www.spinics.net/lists/linux-omap/msg127425.html

Fixes: 55ee7017ee31 ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/arm/mach-omap2/board-generic.c |    2 +-
 arch/arm/mach-omap2/timer.c         |    9 +++++----
 2 files changed, 6 insertions(+), 5 deletions(-)

--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -306,7 +306,7 @@ DT_MACHINE_START(AM43_DT, "Generic AM43
 	.init_late	= am43xx_init_late,
 	.init_irq	= omap_gic_of_init,
 	.init_machine	= omap_generic_init,
-	.init_time	= omap4_local_timer_init,
+	.init_time	= omap3_gptimer_timer_init,
 	.dt_compat	= am43_boards_compat,
 	.restart	= omap44xx_restart,
 MACHINE_END
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -510,18 +510,19 @@ void __init omap3_secure_sync32k_timer_i
 }
 #endif /* CONFIG_ARCH_OMAP3 */
 
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX)
+#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_SOC_AM33XX) || \
+	defined(CONFIG_SOC_AM43XX)
 void __init omap3_gptimer_timer_init(void)
 {
 	__omap_sync32k_timer_init(2, "timer_sys_ck", NULL,
 			1, "timer_sys_ck", "ti,timer-alwon", true);
-
-	clocksource_probe();
+	if (of_have_populated_dt())
+		clocksource_probe();
 }
 #endif
 
 #if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) ||		\
-	defined(CONFIG_SOC_DRA7XX) || defined(CONFIG_SOC_AM43XX)
+	defined(CONFIG_SOC_DRA7XX)
 static void __init omap4_sync32k_timer_init(void)
 {
 	__omap_sync32k_timer_init(1, "timer_32k_ck", "ti,timer-alwon",

[PATCH 4.9 56/59] ALSA: usb-audio: Add a quirk for Plantronics BT600

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Dennis Kadioglu <denk@post.com>

commit 2e40795c3bf344cfb5220d94566205796e3ef19a upstream.

Plantronics BT600 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1" and "cannot get freq at
ep 0x82". This patch adds the USB ID of the BT600 to quirks.c and
avoids those error messages.

Signed-off-by: Dennis Kadioglu <denk@post.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/usb/quirks.c |    1 +
 1 file changed, 1 insertion(+)

--- a/sound/usb/quirks.c
+++ b/sound/usb/quirks.c
@@ -1135,6 +1135,7 @@ bool snd_usb_get_sample_rate_quirk(struc
 	case USB_ID(0x045E, 0x076F): /* MS Lifecam HD-6000 */
 	case USB_ID(0x045E, 0x0772): /* MS Lifecam Studio */
 	case USB_ID(0x045E, 0x0779): /* MS Lifecam HD-3000 */
+	case USB_ID(0x047F, 0x02F7): /* Plantronics BT-600 */
 	case USB_ID(0x047F, 0x0415): /* Plantronics BT-300 */
 	case USB_ID(0x047F, 0xAA05): /* Plantronics DA45 */
 	case USB_ID(0x04D8, 0xFEEA): /* Benchmark DAC1 Pre */

[PATCH 4.9 58/59] rtlwifi: Fix enter/exit power_save

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Larry Finger <Larry.Finger@lwfinger.net>

commit ba9f93f82abafe2552eac942ebb11c2df4f8dd7f upstream.

In commit a5ffbe0a1993 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.

This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.

Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/realtek/rtlwifi/base.c |    8 +++---
 drivers/net/wireless/realtek/rtlwifi/core.c |    9 ++-----
 drivers/net/wireless/realtek/rtlwifi/pci.c  |   14 +++-------
 drivers/net/wireless/realtek/rtlwifi/ps.c   |   36 +++++++++++++++++++++-------
 4 files changed, 40 insertions(+), 27 deletions(-)

--- a/drivers/net/wireless/realtek/rtlwifi/base.c
+++ b/drivers/net/wireless/realtek/rtlwifi/base.c
@@ -1303,12 +1303,13 @@ EXPORT_SYMBOL_GPL(rtl_action_proc);
 
 static void setup_arp_tx(struct rtl_priv *rtlpriv, struct rtl_ps_ctl *ppsc)
 {
+	struct ieee80211_hw *hw = rtlpriv->hw;
+
 	rtlpriv->ra.is_special_data = true;
 	if (rtlpriv->cfg->ops->get_btc_status())
 		rtlpriv->btcoexist.btc_ops->btc_special_packet_notify(
 					rtlpriv, 1);
-	rtlpriv->enter_ps = false;
-	schedule_work(&rtlpriv->works.lps_change_work);
+	rtl_lps_leave(hw);
 	ppsc->last_delaylps_stamp_jiffies = jiffies;
 }
 
@@ -1381,8 +1382,7 @@ u8 rtl_is_special_data(struct ieee80211_
 
 		if (is_tx) {
 			rtlpriv->ra.is_special_data = true;
-			rtlpriv->enter_ps = false;
-			schedule_work(&rtlpriv->works.lps_change_work);
+			rtl_lps_leave(hw);
 			ppsc->last_delaylps_stamp_jiffies = jiffies;
 		}
 
--- a/drivers/net/wireless/realtek/rtlwifi/core.c
+++ b/drivers/net/wireless/realtek/rtlwifi/core.c
@@ -1150,10 +1150,8 @@ static void rtl_op_bss_info_changed(stru
 		} else {
 			mstatus = RT_MEDIA_DISCONNECT;
 
-			if (mac->link_state == MAC80211_LINKED) {
-				rtlpriv->enter_ps = false;
-				schedule_work(&rtlpriv->works.lps_change_work);
-			}
+			if (mac->link_state == MAC80211_LINKED)
+				rtl_lps_leave(hw);
 			if (ppsc->p2p_ps_info.p2p_ps_mode > P2P_PS_NONE)
 				rtl_p2p_ps_cmd(hw, P2P_PS_DISABLE);
 			mac->link_state = MAC80211_NOLINK;
@@ -1431,8 +1429,7 @@ static void rtl_op_sw_scan_start(struct
 	}
 
 	if (mac->link_state == MAC80211_LINKED) {
-		rtlpriv->enter_ps = false;
-		schedule_work(&rtlpriv->works.lps_change_work);
+		rtl_lps_leave(hw);
 		mac->link_state = MAC80211_LINKED_SCANNING;
 	} else {
 		rtl_ips_nic_on(hw);
--- a/drivers/net/wireless/realtek/rtlwifi/pci.c
+++ b/drivers/net/wireless/realtek/rtlwifi/pci.c
@@ -663,11 +663,9 @@ tx_status_ok:
 	}
 
 	if (((rtlpriv->link_info.num_rx_inperiod +
-		rtlpriv->link_info.num_tx_inperiod) > 8) ||
-		(rtlpriv->link_info.num_rx_inperiod > 2)) {
-		rtlpriv->enter_ps = false;
-		schedule_work(&rtlpriv->works.lps_change_work);
-	}
+	      rtlpriv->link_info.num_tx_inperiod) > 8) ||
+	      (rtlpriv->link_info.num_rx_inperiod > 2))
+		rtl_lps_leave(hw);
 }
 
 static int _rtl_pci_init_one_rxdesc(struct ieee80211_hw *hw,
@@ -918,10 +916,8 @@ new_trx_end:
 		}
 		if (((rtlpriv->link_info.num_rx_inperiod +
 		      rtlpriv->link_info.num_tx_inperiod) > 8) ||
-		      (rtlpriv->link_info.num_rx_inperiod > 2)) {
-			rtlpriv->enter_ps = false;
-			schedule_work(&rtlpriv->works.lps_change_work);
-		}
+		      (rtlpriv->link_info.num_rx_inperiod > 2))
+			rtl_lps_leave(hw);
 		skb = new_skb;
 no_new:
 		if (rtlpriv->use_new_trx_flow) {
--- a/drivers/net/wireless/realtek/rtlwifi/ps.c
+++ b/drivers/net/wireless/realtek/rtlwifi/ps.c
@@ -407,8 +407,8 @@ void rtl_lps_set_psmode(struct ieee80211
 	}
 }
 
-/*Enter the leisure power save mode.*/
-void rtl_lps_enter(struct ieee80211_hw *hw)
+/* Interrupt safe routine to enter the leisure power save mode.*/
+static void rtl_lps_enter_core(struct ieee80211_hw *hw)
 {
 	struct rtl_mac *mac = rtl_mac(rtl_priv(hw));
 	struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
@@ -444,10 +444,9 @@ void rtl_lps_enter(struct ieee80211_hw *
 
 	spin_unlock_irqrestore(&rtlpriv->locks.lps_lock, flag);
 }
-EXPORT_SYMBOL(rtl_lps_enter);
 
-/*Leave the leisure power save mode.*/
-void rtl_lps_leave(struct ieee80211_hw *hw)
+/* Interrupt safe routine to leave the leisure power save mode.*/
+static void rtl_lps_leave_core(struct ieee80211_hw *hw)
 {
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
 	struct rtl_ps_ctl *ppsc = rtl_psc(rtl_priv(hw));
@@ -477,7 +476,6 @@ void rtl_lps_leave(struct ieee80211_hw *
 	}
 	spin_unlock_irqrestore(&rtlpriv->locks.lps_lock, flag);
 }
-EXPORT_SYMBOL(rtl_lps_leave);
 
 /* For sw LPS*/
 void rtl_swlps_beacon(struct ieee80211_hw *hw, void *data, unsigned int len)
@@ -670,12 +668,34 @@ void rtl_lps_change_work_callback(struct
 	struct rtl_priv *rtlpriv = rtl_priv(hw);
 
 	if (rtlpriv->enter_ps)
-		rtl_lps_enter(hw);
+		rtl_lps_enter_core(hw);
 	else
-		rtl_lps_leave(hw);
+		rtl_lps_leave_core(hw);
 }
 EXPORT_SYMBOL_GPL(rtl_lps_change_work_callback);
 
+void rtl_lps_enter(struct ieee80211_hw *hw)
+{
+	struct rtl_priv *rtlpriv = rtl_priv(hw);
+
+	if (!in_interrupt())
+		return rtl_lps_enter_core(hw);
+	rtlpriv->enter_ps = true;
+	schedule_work(&rtlpriv->works.lps_change_work);
+}
+EXPORT_SYMBOL_GPL(rtl_lps_enter);
+
+void rtl_lps_leave(struct ieee80211_hw *hw)
+{
+	struct rtl_priv *rtlpriv = rtl_priv(hw);
+
+	if (!in_interrupt())
+		return rtl_lps_leave_core(hw);
+	rtlpriv->enter_ps = false;
+	schedule_work(&rtlpriv->works.lps_change_work);
+}
+EXPORT_SYMBOL_GPL(rtl_lps_leave);
+
 void rtl_swlps_wq_callback(void *data)
 {
 	struct rtl_works *rtlworks = container_of_dwork_rtl(data,

[PATCH 4.9 59/59] rtlwifi: rtl_usb: Fix missing entry in USB drivers private data

[Greg Kroah-Hartman]

4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Larry Finger <Larry.Finger@lwfinger.net>

commit 60f59ce0278557f7896d5158ae6d12a4855a72cc upstream.

These drivers need to be able to reference "struct ieee80211_hw" from
the driver's private data, and vice versa. The USB driver failed to
store the address of ieee80211_hw in the private data. Although this
bug has been present for a long time, it was not exposed until
commit ba9f93f82aba ("rtlwifi: Fix enter/exit power_save").

Fixes: ba9f93f82aba ("rtlwifi: Fix enter/exit power_save")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/realtek/rtlwifi/usb.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/net/wireless/realtek/rtlwifi/usb.c
+++ b/drivers/net/wireless/realtek/rtlwifi/usb.c
@@ -1067,6 +1067,7 @@ int rtl_usb_probe(struct usb_interface *
 		return -ENOMEM;
 	}
 	rtlpriv = hw->priv;
+	rtlpriv->hw = hw;
 	rtlpriv->usb_data = kzalloc(RTL_USB_MAX_RX_COUNT * sizeof(u32),
 				    GFP_KERNEL);
 	if (!rtlpriv->usb_data)

Re: [PATCH 4.9 00/59] 4.9.4-stable review

[Guenter Roeck]

On Fri, Jan 13, 2017 at 01:01:07PM +0100, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.9.4 release.
> There are 59 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Sun Jan 15 11:38:27 UTC 2017.
> Anything received after that time might be too late.
> 

Build results:
	total: 149 pass: 149 fail: 0
Qemu test results:
	total: 122 pass: 122 fail: 0

Details are available at http://kerneltests.org/builders.

Guenter

Re: [PATCH 4.9 00/59] 4.9.4-stable review

[Shuah Khan]

On 01/13/2017 05:01 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 4.9.4 release.
> There are 59 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Sun Jan 15 11:38:27 UTC 2017.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.4-rc1.gz
> or in the git tree and branch at:
>   git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h
> 

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

-- 
Shuah Khan
Sr. Linux Kernel Developer
Open Source Innovation Group
Samsung Research America(Silicon Valley)
shuah.kh@samsung.com

Re: [PATCH 4.9 00/59] 4.9.4-stable review

[Greg Kroah-Hartman]

On Fri, Jan 13, 2017 at 12:20:20PM -0800, Guenter Roeck wrote:
> On Fri, Jan 13, 2017 at 01:01:07PM +0100, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 4.9.4 release.
> > There are 59 patches in this series, all will be posted as a response
> > to this one.  If anyone has any issues with these being applied, please
> > let me know.
> > 
> > Responses should be made by Sun Jan 15 11:38:27 UTC 2017.
> > Anything received after that time might be too late.
> > 
> 
> Build results:
> 	total: 149 pass: 149 fail: 0
> Qemu test results:
> 	total: 122 pass: 122 fail: 0
> 
> Details are available at http://kerneltests.org/builders.

Thanks for testing all of these and letting me know.

greg k-h

Re: [PATCH 4.9 00/59] 4.9.4-stable review

[Greg Kroah-Hartman]

On Fri, Jan 13, 2017 at 02:58:09PM -0700, Shuah Khan wrote:
> On 01/13/2017 05:01 AM, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 4.9.4 release.
> > There are 59 patches in this series, all will be posted as a response
> > to this one.  If anyone has any issues with these being applied, please
> > let me know.
> > 
> > Responses should be made by Sun Jan 15 11:38:27 UTC 2017.
> > Anything received after that time might be too late.
> > 
> > The whole patch series can be found in one patch at:
> > 	kernel.org/pub/linux/kernel/v4.x/stable-review/patch-4.9.4-rc1.gz
> > or in the git tree and branch at:
> >   git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-4.9.y
> > and the diffstat can be found below.
> > 
> > thanks,
> > 
> > greg k-h
> > 
> 
> Compiled and booted on my test system. No dmesg regressions.

Thanks for testing these and letting me know.

greg k-h