* [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
@ 2017-04-06 13:04 Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board Wadim Egorov
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Wadim Egorov @ 2017-04-06 13:04 UTC (permalink / raw)
To: robh+dt, mark.rutland, heiko, linux, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=y, Size: 13703 bytes --]
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
---
Changes in v2:
- Added a dual license which is used for all rk3288 based boards.
Include minor changes from Heiko Stübner:
- moved phy-handle property up a bit
- switches compatible and #address+#size-cells in mdio0
- dropped rockchip,grf from &io_domains (grf is a simple-mfd and can
get the grf syscon on its own via its parent)
- vdd_cpu: regulator@60 (from fan53555@60)
- serial_flash: flash@0 (from m25p80@0)
Nodes should be named after their "category" not the actual device
---
arch/arm/boot/dts/rk3288-phycore-som.dtsi | 497 ++++++++++++++++++++++++++++++
1 file changed, 497 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/rk3288-phycore-som.dtsi b/arch/arm/boot/dts/rk3288-phycore-som.dtsi
new file mode 100644
index 0000000..26cd3ad
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-phycore-som.dtsi
@@ -0,0 +1,497 @@
+/*
+ * Device tree file for Phytec phyCORE-RK3288 SoM
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include "rk3288.dtsi"
+
+/ {
+ model = "Phytec RK3288 phyCORE";
+ compatible = "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+ /*
+ * Set the minimum memory size here and
+ * let the bootloader set the real size.
+ */
+ memory {
+ device_type = "memory";
+ reg = <0 0x8000000>;
+ };
+
+ aliases {
+ rtc0 = &i2c_rtc;
+ rtc1 = &rk818;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ leds: user-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_led>;
+
+ user {
+ label = "green_led";
+ gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "keep";
+ };
+ };
+
+ vdd_emmc_io: vdd-emmc-io {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_emmc_io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vdd_3v3_io>;
+ };
+
+ vdd_in_otg_out: vdd-in-otg-out {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_in_otg_out";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vdd_misc_1v8: vdd-misc-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_misc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+ operating-points = <
+ /* KHz uV */
+ 1800000 1400000
+ 1608000 1350000
+ 1512000 1300000
+ 1416000 1200000
+ 1200000 1100000
+ 1008000 1050000
+ 816000 1000000
+ 696000 950000
+ 600000 900000
+ 408000 900000
+ 312000 900000
+ 216000 900000
+ 126000 900000
+ >;
+};
+
+&emmc {
+ status = "okay";
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+ vmmc-supply = <&vdd_3v3_io>;
+ vqmmc-supply = <&vdd_emmc_io>;
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ clock_in_out = "input";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins &phy_rst &phy_int>;
+ phy-handle = <&phy0>;
+ phy-supply = <&vdd_eth_2v5>;
+ phy-mode = "rgmii-id";
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+ tx_delay = <0x0>;
+ rx_delay = <0x0>;
+
+ mdio0 {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ enet-phy-lane-no-swap;
+ };
+ };
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+};
+
+&io_domains {
+ status = "okay";
+ sdcard-supply = <&vdd_io_sd>;
+ flash0-supply = <&vdd_emmc_io>;
+ flash1-supply = <&vdd_misc_1v8>;
+ gpio1830-supply = <&vdd_3v3_io>;
+ gpio30-supply = <&vdd_3v3_io>;
+ bb-supply = <&vdd_3v3_io>;
+ dvp-supply = <&vdd_3v3_io>;
+ lcdc-supply = <&vdd_3v3_io>;
+ wifi-supply = <&vdd_3v3_io>;
+ audio-supply = <&vdd_3v3_io>;
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ rk818: pmic@1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ boost-supply = <&vdd_in_otg_out>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_misc_1v8>;
+ vcc8-supply = <&vdd_misc_1v8>;
+ vcc9-supply = <&vdd_3v3_io>;
+ vddio-supply = <&vdd_3v3_io>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_3v3_io: DCDC_REG4 {
+ regulator-name = "vdd_3v3_io";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd_sys: DCDC_BOOST {
+ regulator-name = "vdd_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <5000000>;
+ };
+ };
+
+ /* vcc9 */
+ vdd_sd: SWITCH_REG {
+ regulator-name = "vdd_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ /* vcc6 */
+ vdd_eth_2v5: LDO_REG2 {
+ regulator-name = "vdd_eth_2v5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2500000>;
+ };
+ };
+
+ /* vcc7 */
+ vdd_1v0: LDO_REG3 {
+ regulator-name = "vdd_1v0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ /* vcc8 */
+ vdd_1v8_lcd_ldo: LDO_REG4 {
+ regulator-name = "vdd_1v8_lcd_ldo";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ /* vcc8 */
+ vdd_1v0_lcd: LDO_REG6 {
+ regulator-name = "vdd_1v0_lcd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ /* vcc7 */
+ vdd_1v8_ldo: LDO_REG7 {
+ regulator-name = "vdd_1v8_ldo";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ /* vcc9 */
+ vdd_io_sd: LDO_REG9 {
+ regulator-name = "vdd_io_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+ };
+ };
+
+ /* M24C32-D */
+ i2c_eeprom: eeprom@50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+
+ vdd_cpu: regulator@60 {
+ compatible = "fcs,fan53555";
+ reg = <0x60>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-enable-ramp-delay = <300>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1430000>;
+ regulator-ramp-delay = <8000>;
+ vin-supply = <&vdd_sys>;
+ };
+};
+
+&pinctrl {
+ pcfg_output_high: pcfg-output-high {
+ output-high;
+ };
+
+ emmc {
+ /*
+ * We run eMMC at max speed; bump up drive strength.
+ * We also have external pulls, so disable the internal ones.
+ */
+ emmc_clk: emmc-clk {
+ rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_12ma>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_12ma>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 1 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 2 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 3 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 4 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 5 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 6 RK_FUNC_2 &pcfg_pull_none_12ma>,
+ <3 7 RK_FUNC_2 &pcfg_pull_none_12ma>;
+ };
+ };
+
+ gmac {
+ phy_int: phy-int {
+ rockchip,pins = <4 2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ phy_rst: phy-rst {
+ rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ leds {
+ user_led: user-led {
+ rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ /* Pin for switching state between sleep and non-sleep state */
+ pmic_sleep: pmic-sleep {
+ rockchip,pins = <RK_GPIO0 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vdd_1v8_ldo>;
+};
+
+&spi2 {
+ status = "okay";
+
+ serial_flash: flash@0 {
+ compatible = "micron,n25q128a13", "jedec,spi-nor";
+ reg = <0x0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "okay";
+ };
+};
+
+&tsadc {
+ status = "okay";
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board
2017-04-06 13:04 [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Wadim Egorov
@ 2017-04-06 13:04 ` Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK Wadim Egorov
` (2 subsequent siblings)
3 siblings, 0 replies; 7+ messages in thread
From: Wadim Egorov @ 2017-04-06 13:04 UTC (permalink / raw)
To: robh+dt, mark.rutland, heiko, linux, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Following interfaces and devices are available on the PCM-947 carrier board:
- 2x UART
- micro SDMMC
- USB host and USB otg
- USB 3503 HSIC hub
- Ethernet
- 2nd alternative KSZ9031 ethernet phy
- Display connectors: PHYTEC LVDS, DDG LVDS, parallel signals, HDMI
- Parallel Camera CIF
- SGTL5000-32QFN audio codec
- 4x LEDs connected via PCA9533
- 2 user buttons
- Expansion connectors for WiFi and other modules
- RTC RV-4162-C7
- Resistive touch STMPE811
- EEPROM M24C32
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
---
Changes in v2:
- Added a dual license which is used for all rk3288 based boards.
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rk3288-phycore-rdk.dts | 298 +++++++++++++++++++++++++++++++
2 files changed, 299 insertions(+)
create mode 100644 arch/arm/boot/dts/rk3288-phycore-rdk.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0118084..8c3cb4d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -692,6 +692,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-firefly.dtb \
rk3288-firefly-reload.dtb \
rk3288-miqi.dtb \
+ rk3288-phycore-rdk.dtb \
rk3288-popmetal.dtb \
rk3288-r89.dtb \
rk3288-rock2-square.dtb \
diff --git a/arch/arm/boot/dts/rk3288-phycore-rdk.dts b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
new file mode 100644
index 0000000..870f96b
--- /dev/null
+++ b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
@@ -0,0 +1,298 @@
+/*
+ * Device tree file for Phytec PCM-947 carrier board
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include "rk3288-phycore-som.dtsi"
+
+/ {
+ model = "Phytec RK3288 PCM-947";
+ compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
+ user_buttons: user-buttons {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_button_pins>;
+
+ button@0 {
+ label = "home";
+ linux,code = <KEY_HOME>;
+ gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+
+ button@1 {
+ label = "menu";
+ linux,code = <KEY_MENU>;
+ gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+ wakeup-source;
+ };
+ };
+
+ vcc_host0_5v: usb-host0-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host0_vbus_drv>;
+ regulator-name = "vcc_host0_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+
+ vcc_host1_5v: usb-host1-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host1_vbus_drv>;
+ regulator-name = "vcc_host1_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+
+ vcc_otg_5v: usb-otg-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc_otg_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&vdd_in_otg_out>;
+ };
+};
+
+&gmac {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ stmpe@44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ };
+
+ adc@64 {
+ compatible = "maxim,max1037";
+ reg = <0x64>;
+ };
+
+ i2c_rtc: rtc@68 {
+ compatible = "rv4162";
+ reg = <0x68>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_rtc_int>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <10 0>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ i2c_eeprom_cb: eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+
+ /* PCA9533 - 4-bit LED dimmer */
+ leddim: leddimmer@62 {
+ compatible = "nxp,pca9533";
+ reg = <0x62>;
+
+ led1 {
+ label = "red:user1";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led2 {
+ label = "green:user2";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led3 {
+ label = "blue:user3";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+
+ led4 {
+ label = "red:user4";
+ linux,default-trigger = "none";
+ type = <PCA9532_TYPE_LED>;
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&pinctrl {
+ pcfg_pull_up_drv_12ma: pcfg-pull-up-drv-12ma {
+ bias-pull-up;
+ drive-strength = <12>;
+ };
+
+ buttons {
+ user_button_pins: user-button-pins {
+ /* button 1 */
+ rockchip,pins = <8 3 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* button 2 */
+ <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ rv4162 {
+ i2c_rtc_int: i2c-rtc-int {
+ rockchip,pins = <5 10 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * Default drive strength isn't enough to achieve even
+ * high-speed mode on pcm-947 board so bump up to 12 mA.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_12ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_12ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_12ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ touchscreen {
+ ts_irq_pin: ts-irq-pin {
+ rockchip,pins = <5 15 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_host {
+ host0_vbus_drv: host0-vbus-drv {
+ rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host1_vbus_drv: host1-vbus-drv {
+ rockchip,pins = <2 0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ vmmc-supply = <&vdd_io_sd>;
+ vqmmc-supply = <&vdd_io_sd>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK
2017-04-06 13:04 [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board Wadim Egorov
@ 2017-04-06 13:04 ` Wadim Egorov
2017-04-10 18:26 ` Rob Herring
2017-04-06 22:21 ` [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Heiko Stuebner
2017-04-18 10:15 ` Jacob Chen
3 siblings, 1 reply; 7+ messages in thread
From: Wadim Egorov @ 2017-04-06 13:04 UTC (permalink / raw)
To: robh+dt, mark.rutland, heiko, linux, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
Add documentation for the PCM-947 carrier board, a RK3288 based
development board made by PHYTEC.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
---
No changes in v2
---
Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index cc4ace6..e079a62 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -103,6 +103,10 @@ Rockchip platforms device tree bindings
Required root node properties:
- compatible = "mqmaker,miqi", "rockchip,rk3288";
+- Phytec phyCORE-RK3288: Rapid Development Kit
+ Required root node properties:
+ - compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
+
- Rockchip PX3 Evaluation board:
Required root node properties:
- compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
2017-04-06 13:04 [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK Wadim Egorov
@ 2017-04-06 22:21 ` Heiko Stuebner
2017-04-18 10:15 ` Jacob Chen
3 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2017-04-06 22:21 UTC (permalink / raw)
To: Wadim Egorov
Cc: robh+dt, mark.rutland, linux, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
Am Donnerstag, 6. April 2017, 15:04:24 CEST schrieb Wadim Egorov:
> The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
> The module can be connected to different carrier boards.
> It can be also equipped with different RAM, SPI flash and eMMC variants.
> The Rapid Development Kit option is using the following setup:
>
> - 1 GB DDR3 RAM (2 Banks)
> - 1x 4 KB EEPROM
> - DP83867 Gigabit Ethernet PHY
> - 16 MB SPI Flash
> - 4 GB eMMC Flash
>
> Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
applied all 3 for 4.12 .
One minor change was making the touchscreen node name in patch2 read
touchscreen@44
Same rationale as before, nodes should be named after the device-category
Heiko
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK
2017-04-06 13:04 ` [PATCH v2 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK Wadim Egorov
@ 2017-04-10 18:26 ` Rob Herring
0 siblings, 0 replies; 7+ messages in thread
From: Rob Herring @ 2017-04-10 18:26 UTC (permalink / raw)
To: Wadim Egorov
Cc: mark.rutland, heiko, linux, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
On Thu, Apr 06, 2017 at 03:04:26PM +0200, Wadim Egorov wrote:
> Add documentation for the PCM-947 carrier board, a RK3288 based
> development board made by PHYTEC.
>
> Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
> ---
> No changes in v2
> ---
> Documentation/devicetree/bindings/arm/rockchip.txt | 4 ++++
> 1 file changed, 4 insertions(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
2017-04-06 13:04 [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Wadim Egorov
` (2 preceding siblings ...)
2017-04-06 22:21 ` [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Heiko Stuebner
@ 2017-04-18 10:15 ` Jacob Chen
2017-04-18 15:01 ` Wadim Egorov
3 siblings, 1 reply; 7+ messages in thread
From: Jacob Chen @ 2017-04-18 10:15 UTC (permalink / raw)
To: Wadim Egorov
Cc: robh+dt, mark.rutland, Heiko Stuebner, linux, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
Hi wadim,
2017-04-06 21:04 GMT+08:00 Wadim Egorov <w.egorov@phytec.de>:
> The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
> The module can be connected to different carrier boards.
> It can be also equipped with different RAM, SPI flash and eMMC variants.
> The Rapid Development Kit option is using the following setup:
>
> - 1 GB DDR3 RAM (2 Banks)
> - 1x 4 KB EEPROM
> - DP83867 Gigabit Ethernet PHY
> - 16 MB SPI Flash
> - 4 GB eMMC Flash
>
> Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
> ---
> Changes in v2:
> - Added a dual license which is used for all rk3288 based boards.
>
> Include minor changes from Heiko Stübner:
> - moved phy-handle property up a bit
> - switches compatible and #address+#size-cells in mdio0
> - dropped rockchip,grf from &io_domains (grf is a simple-mfd and can
> get the grf syscon on its own via its parent)
> - vdd_cpu: regulator@60 (from fan53555@60)
> - serial_flash: flash@0 (from m25p80@0)
> Nodes should be named after their "category" not the actual device
>
> ---
> arch/arm/boot/dts/rk3288-phycore-som.dtsi | 497 ++++++++++++++++++++++++++++++
> 1 file changed, 497 insertions(+)
> create mode 100644 arch/arm/boot/dts/rk3288-phycore-som.dtsi
>
> diff --git a/arch/arm/boot/dts/rk3288-phycore-som.dtsi b/arch/arm/boot/dts/rk3288-phycore-som.dtsi
> new file mode 100644
> index 0000000..26cd3ad
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3288-phycore-som.dtsi
> @@ -0,0 +1,497 @@
> +/*
> + * Device tree file for Phytec phyCORE-RK3288 SoM
> + * Copyright (C) 2017 PHYTEC Messtechnik GmbH
> + * Author: Wadim Egorov <w.egorov@phytec.de>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include "rk3288.dtsi"
> +
> +/ {
> + model = "Phytec RK3288 phyCORE";
> + compatible = "phytec,rk3288-phycore-som", "rockchip,rk3288";
> +
> + /*
> + * Set the minimum memory size here and
> + * let the bootloader set the real size.
> + */
> + memory {
> + device_type = "memory";
> + reg = <0 0x8000000>;
> + };
> +
> + aliases {
> + rtc0 = &i2c_rtc;
> + rtc1 = &rk818;
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + leds: user-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&user_led>;
> +
> + user {
> + label = "green_led";
> + gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + default-state = "keep";
> + };
> + };
> +
> + vdd_emmc_io: vdd-emmc-io {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_emmc_io";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vdd_3v3_io>;
> + };
> +
> + vdd_in_otg_out: vdd-in-otg-out {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_in_otg_out";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + vdd_misc_1v8: vdd-misc-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_misc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +};
> +
> +&cpu0 {
> + cpu0-supply = <&vdd_cpu>;
> + operating-points = <
> + /* KHz uV */
> + 1800000 1400000
> + 1608000 1350000
> + 1512000 1300000
> + 1416000 1200000
> + 1200000 1100000
> + 1008000 1050000
> + 816000 1000000
> + 696000 950000
> + 600000 900000
> + 408000 900000
> + 312000 900000
> + 216000 900000
> + 126000 900000
> + >;
> +};
> +
> +&emmc {
> + status = "okay";
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + disable-wp;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
> + vmmc-supply = <&vdd_3v3_io>;
> + vqmmc-supply = <&vdd_emmc_io>;
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + clock_in_out = "input";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins &phy_rst &phy_int>;
> + phy-handle = <&phy0>;
> + phy-supply = <&vdd_eth_2v5>;
> + phy-mode = "rgmii-id";
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> + tx_delay = <0x0>;
> + rx_delay = <0x0>;
> +
> + mdio0 {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + phy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + enet-phy-lane-no-swap;
> + };
> + };
> +};
> +
> +&hdmi {
> + ddc-i2c-bus = <&i2c5>;
> +};
> +
> +&io_domains {
> + status = "okay";
> + sdcard-supply = <&vdd_io_sd>;
> + flash0-supply = <&vdd_emmc_io>;
> + flash1-supply = <&vdd_misc_1v8>;
> + gpio1830-supply = <&vdd_3v3_io>;
> + gpio30-supply = <&vdd_3v3_io>;
> + bb-supply = <&vdd_3v3_io>;
> + dvp-supply = <&vdd_3v3_io>;
> + lcdc-supply = <&vdd_3v3_io>;
> + wifi-supply = <&vdd_3v3_io>;
> + audio-supply = <&vdd_3v3_io>;
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + rk818: pmic@1c {
> + compatible = "rockchip,rk818";
> + reg = <0x1c>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> +
I think you miss "clock-output-names = "xin32k" here.
> + vcc1-supply = <&vdd_sys>;
> + vcc2-supply = <&vdd_sys>;
> + vcc3-supply = <&vdd_sys>;
> + vcc4-supply = <&vdd_sys>;
> + boost-supply = <&vdd_in_otg_out>;
> + vcc6-supply = <&vdd_sys>;
> + vcc7-supply = <&vdd_misc_1v8>;
> + vcc8-supply = <&vdd_misc_1v8>;
> + vcc9-supply = <&vdd_3v3_io>;
> + vddio-supply = <&vdd_3v3_io>;
> +
> + regulators {
> + vdd_log: DCDC_REG1 {
> + regulator-name = "vdd_log";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-name = "vdd_gpu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vdd_3v3_io: DCDC_REG4 {
> + regulator-name = "vdd_3v3_io";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vdd_sys: DCDC_BOOST {
> + regulator-name = "vdd_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <5000000>;
> + };
> + };
> +
> + /* vcc9 */
> + vdd_sd: SWITCH_REG {
> + regulator-name = "vdd_sd";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + /* vcc6 */
> + vdd_eth_2v5: LDO_REG2 {
> + regulator-name = "vdd_eth_2v5";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <2500000>;
> + };
> + };
> +
> + /* vcc7 */
> + vdd_1v0: LDO_REG3 {
> + regulator-name = "vdd_1v0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + /* vcc8 */
> + vdd_1v8_lcd_ldo: LDO_REG4 {
> + regulator-name = "vdd_1v8_lcd_ldo";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + /* vcc8 */
> + vdd_1v0_lcd: LDO_REG6 {
> + regulator-name = "vdd_1v0_lcd";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + /* vcc7 */
> + vdd_1v8_ldo: LDO_REG7 {
> + regulator-name = "vdd_1v8_ldo";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + /* vcc9 */
> + vdd_io_sd: LDO_REG9 {
> + regulator-name = "vdd_io_sd";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> + };
> + };
> +
> + /* M24C32-D */
> + i2c_eeprom: eeprom@50 {
> + compatible = "atmel,24c32";
> + reg = <0x50>;
> + pagesize = <32>;
> + };
> +
> + vdd_cpu: regulator@60 {
> + compatible = "fcs,fan53555";
> + reg = <0x60>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-enable-ramp-delay = <300>;
> + regulator-name = "vdd_cpu";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1430000>;
> + regulator-ramp-delay = <8000>;
> + vin-supply = <&vdd_sys>;
> + };
> +};
> +
> +&pinctrl {
> + pcfg_output_high: pcfg-output-high {
> + output-high;
> + };
> +
> + emmc {
> + /*
> + * We run eMMC at max speed; bump up drive strength.
> + * We also have external pulls, so disable the internal ones.
> + */
> + emmc_clk: emmc-clk {
> + rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_12ma>;
> + };
> +
> + emmc_cmd: emmc-cmd {
> + rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_12ma>;
> + };
> +
> + emmc_bus8: emmc-bus8 {
> + rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 1 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 2 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 3 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 4 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 5 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 6 RK_FUNC_2 &pcfg_pull_none_12ma>,
> + <3 7 RK_FUNC_2 &pcfg_pull_none_12ma>;
> + };
> + };
> +
> + gmac {
> + phy_int: phy-int {
> + rockchip,pins = <4 2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + phy_rst: phy-rst {
> + rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
> + };
> + };
> +
> + leds {
> + user_led: user-led {
> + rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_output_high>;
> + };
> + };
> +
> + pmic {
> + pmic_int: pmic-int {
> + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + /* Pin for switching state between sleep and non-sleep state */
> + pmic_sleep: pmic-sleep {
> + rockchip,pins = <RK_GPIO0 0 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&saradc {
> + status = "okay";
> + vref-supply = <&vdd_1v8_ldo>;
> +};
> +
> +&spi2 {
> + status = "okay";
> +
> + serial_flash: flash@0 {
> + compatible = "micron,n25q128a13", "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <50000000>;
> + m25p,fast-read;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + status = "okay";
> + };
> +};
> +
> +&tsadc {
> + status = "okay";
> + rockchip,hw-tshut-mode = <0>;
> + rockchip,hw-tshut-polarity = <0>;
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&vopl {
> + status = "okay";
> +};
> +
> +&vopl_mmu {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
2017-04-18 10:15 ` Jacob Chen
@ 2017-04-18 15:01 ` Wadim Egorov
0 siblings, 0 replies; 7+ messages in thread
From: Wadim Egorov @ 2017-04-18 15:01 UTC (permalink / raw)
To: Jacob Chen
Cc: robh+dt, mark.rutland, Heiko Stuebner, linux, devicetree,
linux-arm-kernel, linux-rockchip, linux-kernel
>> +&i2c0 {
>> + status = "okay";
>> + clock-frequency = <400000>;
>> +
>> + rk818: pmic@1c {
>> + compatible = "rockchip,rk818";
>> + reg = <0x1c>;
>> + interrupt-parent = <&gpio0>;
>> + interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pmic_int>;
>> + rockchip,system-power-controller;
>> + wakeup-source;
>> + #clock-cells = <1>;
>> +
> I think you miss "clock-output-names = "xin32k" here.
Yes, thanks for catching that. I will fix this later.
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2017-04-18 15:01 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-04-06 13:04 [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 2/3] ARM: dts: rockchip: Add support for PCM-947 carrier board Wadim Egorov
2017-04-06 13:04 ` [PATCH v2 3/3] dt-bindings: Document Phytec phyCORE-RK3288 RDK Wadim Egorov
2017-04-10 18:26 ` Rob Herring
2017-04-06 22:21 ` [PATCH v2 1/3] ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM Heiko Stuebner
2017-04-18 10:15 ` Jacob Chen
2017-04-18 15:01 ` Wadim Egorov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).