* [PATCH v2 00/12] arm64: dts: hi3660: add device nodes
@ 2017-05-25 8:18 Guodong Xu
2017-05-25 8:18 ` [PATCH v2 01/12] dt-bindings: arm: hisilicon: add bindings for HiKey960 board Guodong Xu
` (11 more replies)
0 siblings, 12 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel, Guodong Xu
This patchset adds various devices nodes for hi3660 and hikey960.
HiKey960 is one of 96boards. For details information about it, please
refer to [1].
[1] https://github.com/96boards/documentation/tree/master/ConsumerEdition/HiKey960
in v2, incorporated review comments from Rob Herring <robh@kernel.org>
* uart4: max-speed should be in slave device bluetooth node
* LEDs: - bt_active triggered by 'hci0-power'
- move out of SoC level
* pinctrl: update dts to use #pinctrl-cells
* uart: add pinctrl information into uart nodes; add label strings.
* chosen: update stdout-path. serial6 is used.
* i2c: add label strings. change reg address to lower case.
* remove unnecessary status="ok"
* gpio-keys: move out of SoC level.
Chen Feng (2):
arm64: dts: hi3660: Add uarts nodes
arm64: dts: hi3660: Add pl031 rtc node
Chen Jun (1):
arm64: dts: hi3660: add power key dts node
Guodong Xu (4):
dt-bindings: arm: hisilicon: add bindings for HiKey960 board
arm64: dts: hisilicon: update compatible string for hikey960
arm64: dts: hikey960: add WL1837 Bluetooth device node
arm64: dts: hikey960: add LED nodes
Wang Xiaoyin (3):
arm64: dts: hikey960: pinctrl: add more pinmux and pinconfig
arm64: dts: hi3660: add gpio dtsi file for Hisilicon Hi3660 SOC
arm64: dts: hi3660: add spi device nodes
Zhangfei Gao (2):
arm64: dts: hi3660: add resources for clock and reset
arm64: dts: Add I2C nodes for Hi3660
.../bindings/arm/hisilicon/hisilicon.txt | 4 +
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 130 +++-
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 601 +++++++++++++++-
.../arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi | 778 +++++++++++++++++++--
4 files changed, 1439 insertions(+), 74 deletions(-)
--
2.10.2
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v2 01/12] dt-bindings: arm: hisilicon: add bindings for HiKey960 board
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 02/12] arm64: dts: hisilicon: update compatible string for hikey960 Guodong Xu
` (10 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel, Guodong Xu
Add bindings for HiKey960 Board.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
index 2e73215..7111fbc8 100644
--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -4,6 +4,10 @@ Hi3660 SoC
Required root node properties:
- compatible = "hisilicon,hi3660";
+HiKey960 Board
+Required root node properties:
+ - compatible = "hisilicon,hi3660-hikey960", "hisilicon,hi3660";
+
Hi3798cv200 SoC
Required root node properties:
- compatible = "hisilicon,hi3798cv200";
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 02/12] arm64: dts: hisilicon: update compatible string for hikey960
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
2017-05-25 8:18 ` [PATCH v2 01/12] dt-bindings: arm: hisilicon: add bindings for HiKey960 board Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 03/12] arm64: dts: hikey960: pinctrl: add more pinmux and pinconfig Guodong Xu
` (9 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel, Guodong Xu
Update compatible string for hikey960. HiKey960 is a develpment board built
with SoC Hi3660.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index 186251f..64875a5 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -12,7 +12,7 @@
/ {
model = "HiKey960";
- compatible = "hisilicon,hi3660";
+ compatible = "hisilicon,hi3660-hikey960", "hisilicon,hi3660";
aliases {
serial5 = &uart5; /* console UART */
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 03/12] arm64: dts: hikey960: pinctrl: add more pinmux and pinconfig
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
2017-05-25 8:18 ` [PATCH v2 01/12] dt-bindings: arm: hisilicon: add bindings for HiKey960 board Guodong Xu
2017-05-25 8:18 ` [PATCH v2 02/12] arm64: dts: hisilicon: update compatible string for hikey960 Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 04/12] arm64: dts: hi3660: add resources for clock and reset Guodong Xu
` (8 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel,
Wang Xiaoyin, Chen Jun, Guodong Xu
From: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
This commit adds more pinmux and pinctrl information for devices
on HiKey960, including i2c, spi, cam, uart, ufs, pcie, csi, pwr_key,
isp, sd/sdio, i2s, and usb.
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
.../arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi | 778 +++++++++++++++++++--
1 file changed, 715 insertions(+), 63 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi
index 719c4bc..7e542d2 100644
--- a/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hikey960-pinctrl.dtsi
@@ -24,6 +24,27 @@
&range 0 7 0
&range 8 116 0>;
+ pmu_pmx_func: pmu_pmx_func {
+ pinctrl-single,pins = <
+ 0x008 MUX_M1 /* PMU1_SSI */
+ 0x00c MUX_M1 /* PMU2_SSI */
+ 0x010 MUX_M1 /* PMU_CLKOUT */
+ 0x100 MUX_M1 /* PMU_HKADC_SSI */
+ >;
+ };
+
+ csi0_pwd_n_pmx_func: csi0_pwd_n_pmx_func {
+ pinctrl-single,pins = <
+ 0x044 MUX_M0 /* CSI0_PWD_N */
+ >;
+ };
+
+ csi1_pwd_n_pmx_func: csi1_pwd_n_pmx_func {
+ pinctrl-single,pins = <
+ 0x04c MUX_M0 /* CSI1_PWD_N */
+ >;
+ };
+
isp0_pmx_func: isp0_pmx_func {
pinctrl-single,pins = <
0x058 MUX_M1 /* ISP_CLK0 */
@@ -40,6 +61,12 @@
>;
};
+ pwr_key_pmx_func: pwr_key_pmx_func {
+ pinctrl-single,pins = <
+ 0x080 MUX_M0 /* GPIO_034 */
+ >;
+ };
+
i2c3_pmx_func: i2c3_pmx_func {
pinctrl-single,pins = <
0x02c MUX_M1 /* I2C3_SCL */
@@ -67,21 +94,10 @@
>;
};
- spi1_pmx_func: spi1_pmx_func {
- pinctrl-single,pins = <
- 0x034 MUX_M1 /* SPI1_CLK */
- 0x038 MUX_M1 /* SPI1_DI */
- 0x03c MUX_M1 /* SPI1_DO */
- 0x040 MUX_M1 /* SPI1_CS_N */
- >;
- };
-
uart0_pmx_func: uart0_pmx_func {
pinctrl-single,pins = <
0x0cc MUX_M2 /* UART0_RXD */
0x0d0 MUX_M2 /* UART0_TXD */
- 0x0d4 MUX_M2 /* UART0_RXD_M */
- 0x0d8 MUX_M2 /* UART0_TXD_M */
>;
};
@@ -138,6 +154,18 @@
0x0d8 MUX_M1 /* UART6_TXD */
>;
};
+
+ cam0_rst_pmx_func: cam0_rst_pmx_func {
+ pinctrl-single,pins = <
+ 0x0c8 MUX_M0 /* CAM0_RST */
+ >;
+ };
+
+ cam1_rst_pmx_func: cam1_rst_pmx_func {
+ pinctrl-single,pins = <
+ 0x124 MUX_M0 /* CAM1_RST */
+ >;
+ };
};
/* [IOMG_MMC0_000, IOMG_MMC0_005] */
@@ -174,6 +202,13 @@
/* pin base, nr pins & gpio function */
pinctrl-single,gpio-range = <&range 0 12 0>;
+ ufs_pmx_func: ufs_pmx_func {
+ pinctrl-single,pins = <
+ 0x000 MUX_M1 /* UFS_REF_CLK */
+ 0x004 MUX_M1 /* UFS_RST_N */
+ >;
+ };
+
spi3_pmx_func: spi3_pmx_func {
pinctrl-single,pins = <
0x008 MUX_M1 /* SPI3_CLK */
@@ -248,17 +283,17 @@
>;
};
- i2c2_pmx_func: i2c2_pmx_func {
+ i2c7_pmx_func: i2c7_pmx_func {
pinctrl-single,pins = <
- 0x024 MUX_M1 /* I2C2_SCL */
- 0x028 MUX_M1 /* I2C2_SDA */
+ 0x024 MUX_M3 /* I2C7_SCL */
+ 0x028 MUX_M3 /* I2C7_SDA */
>;
};
- i2c7_pmx_func: i2c7_pmx_func {
+ pcie_pmx_func: pcie_pmx_func {
pinctrl-single,pins = <
- 0x024 MUX_M3 /* I2C7_SCL */
- 0x028 MUX_M3 /* I2C7_SDA */
+ 0x084 MUX_M1 /* PCIE_CLKREQ_N */
+ 0x088 MUX_M1 /* PCIE_WAKE_N */
>;
};
@@ -271,15 +306,6 @@
>;
};
- spi4_pmx_func: spi4_pmx_func {
- pinctrl-single,pins = <
- 0x08c MUX_M4 /* SPI4_CLK */
- 0x090 MUX_M4 /* SPI4_DI */
- 0x094 MUX_M4 /* SPI4_DO */
- 0x098 MUX_M4 /* SPI4_CS0_N */
- >;
- };
-
i2s0_pmx_func: i2s0_pmx_func {
pinctrl-single,pins = <
0x034 MUX_M1 /* I2S0_DI */
@@ -290,17 +316,18 @@
};
};
- pmx5: pinmux@ff3fd800 {
+ pmx5: pinmux@e896c800 {
compatible = "pinconf-single";
- reg = <0x0 0xff3fd800 0x0 0x18>;
+ reg = <0x0 0xe896c800 0x0 0x200>;
#pinctrl-cells = <1>;
- #address-cells = <1>;
- #size-cells = <1>;
- pinctrl-single,register-width = <32>;
+ pinctrl-single,register-width = <0x20>;
- sdio_clk_cfg_func: sdio_clk_cfg_func {
+ pmu_cfg_func: pmu_cfg_func {
pinctrl-single,pins = <
- 0x000 0x0 /* SDIO_CLK */
+ 0x010 0x0 /* PMU1_SSI */
+ 0x014 0x0 /* PMU2_SSI */
+ 0x018 0x0 /* PMU_CLKOUT */
+ 0x10c 0x0 /* PMU_HKADC_SSI */
>;
pinctrl-single,bias-pulldown = <
PULL_DIS
@@ -315,18 +342,35 @@
PULL_UP
>;
pinctrl-single,drive-strength = <
- DRIVE6_32MA
- DRIVE6_MASK
+ DRIVE7_06MA DRIVE6_MASK
>;
};
- sdio_cfg_func: sdio_cfg_func {
+ i2c3_cfg_func: i2c3_cfg_func {
pinctrl-single,pins = <
- 0x004 0x0 /* SDIO_CMD */
- 0x008 0x0 /* SDIO_DATA0 */
- 0x00c 0x0 /* SDIO_DATA1 */
- 0x010 0x0 /* SDIO_DATA2 */
- 0x014 0x0 /* SDIO_DATA3 */
+ 0x038 0x0 /* I2C3_SCL */
+ 0x03c 0x0 /* I2C3_SDA */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ csi0_pwd_n_cfg_func: csi0_pwd_n_cfg_func {
+ pinctrl-single,pins = <
+ 0x050 0x0 /* CSI0_PWD_N */
>;
pinctrl-single,bias-pulldown = <
PULL_DIS
@@ -335,29 +379,64 @@
PULL_DOWN
>;
pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+
+ csi1_pwd_n_cfg_func: csi1_pwd_n_cfg_func {
+ pinctrl-single,pins = <
+ 0x058 0x0 /* CSI1_PWD_N */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
PULL_UP
PULL_DIS
PULL_UP
>;
pinctrl-single,drive-strength = <
- DRIVE6_19MA
- DRIVE6_MASK
+ DRIVE7_04MA DRIVE6_MASK
>;
};
- };
- pmx6: pinmux@ff37e800 {
- compatible = "pinconf-single";
- reg = <0x0 0xff37e800 0x0 0x18>;
- #pinctrl-cells = <1>;
- #address-cells = <1>;
- #size-cells = <1>;
- pinctrl-single,register-width = <32>;
+ isp0_cfg_func: isp0_cfg_func {
+ pinctrl-single,pins = <
+ 0x064 0x0 /* ISP_CLK0 */
+ 0x070 0x0 /* ISP_SCL0 */
+ 0x074 0x0 /* ISP_SDA0 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK>;
+ };
- sd_clk_cfg_func: sd_clk_cfg_func {
+ isp1_cfg_func: isp1_cfg_func {
pinctrl-single,pins = <
- 0x000 0x0 /* SD_CLK */
+ 0x068 0x0 /* ISP_CLK1 */
+ 0x078 0x0 /* ISP_SCL1 */
+ 0x07c 0x0 /* ISP_SDA1 */
>;
pinctrl-single,bias-pulldown = <
PULL_DIS
@@ -372,18 +451,37 @@
PULL_UP
>;
pinctrl-single,drive-strength = <
- DRIVE6_32MA
- DRIVE6_MASK
+ DRIVE7_04MA DRIVE6_MASK
>;
};
- sd_cfg_func: sd_cfg_func {
+ pwr_key_cfg_func: pwr_key_cfg_func {
pinctrl-single,pins = <
- 0x004 0x0 /* SD_CMD */
- 0x008 0x0 /* SD_DATA0 */
- 0x00c 0x0 /* SD_DATA1 */
- 0x010 0x0 /* SD_DATA2 */
- 0x014 0x0 /* SD_DATA3 */
+ 0x08c 0x0 /* GPIO_034 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ uart1_cfg_func: uart1_cfg_func {
+ pinctrl-single,pins = <
+ 0x0b4 0x0 /* UART1_RXD */
+ 0x0b8 0x0 /* UART1_TXD */
+ 0x0bc 0x0 /* UART1_CTS_N */
+ 0x0c0 0x0 /* UART1_RTS_N */
>;
pinctrl-single,bias-pulldown = <
PULL_DIS
@@ -392,14 +490,568 @@
PULL_DOWN
>;
pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ uart2_cfg_func: uart2_cfg_func {
+ pinctrl-single,pins = <
+ 0x0c8 0x0 /* UART2_CTS_N */
+ 0x0cc 0x0 /* UART2_RTS_N */
+ 0x0d0 0x0 /* UART2_TXD */
+ 0x0d4 0x0 /* UART2_RXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
PULL_UP
PULL_DIS
PULL_UP
>;
pinctrl-single,drive-strength = <
- DRIVE6_19MA
- DRIVE6_MASK
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ uart5_cfg_func: uart5_cfg_func {
+ pinctrl-single,pins = <
+ 0x0c8 0x0 /* UART5_RXD */
+ 0x0cc 0x0 /* UART5_TXD */
+ 0x0d0 0x0 /* UART5_CTS_N */
+ 0x0d4 0x0 /* UART5_RTS_N */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ cam0_rst_cfg_func: cam0_rst_cfg_func {
+ pinctrl-single,pins = <
+ 0x0d4 0x0 /* CAM0_RST */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+
+ uart0_cfg_func: uart0_cfg_func {
+ pinctrl-single,pins = <
+ 0x0d8 0x0 /* UART0_RXD */
+ 0x0dc 0x0 /* UART0_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ uart6_cfg_func: uart6_cfg_func {
+ pinctrl-single,pins = <
+ 0x0d8 0x0 /* UART6_CTS_N */
+ 0x0dc 0x0 /* UART6_RTS_N */
+ 0x0e0 0x0 /* UART6_RXD */
+ 0x0e4 0x0 /* UART6_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ uart3_cfg_func: uart3_cfg_func {
+ pinctrl-single,pins = <
+ 0x0e8 0x0 /* UART3_CTS_N */
+ 0x0ec 0x0 /* UART3_RTS_N */
+ 0x0f0 0x0 /* UART3_RXD */
+ 0x0f4 0x0 /* UART3_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ uart4_cfg_func: uart4_cfg_func {
+ pinctrl-single,pins = <
+ 0x0f8 0x0 /* UART4_CTS_N */
+ 0x0fc 0x0 /* UART4_RTS_N */
+ 0x100 0x0 /* UART4_RXD */
+ 0x104 0x0 /* UART4_TXD */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ cam1_rst_cfg_func: cam1_rst_cfg_func {
+ pinctrl-single,pins = <
+ 0x130 0x0 /* CAM1_RST */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_04MA DRIVE6_MASK
+ >;
+ };
+ };
+
+ pmx6: pinmux@ff3b6800 {
+ compatible = "pinconf-single";
+ reg = <0x0 0xff3b6800 0x0 0x18>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <0x20>;
+
+ ufs_cfg_func: ufs_cfg_func {
+ pinctrl-single,pins = <
+ 0x000 0x0 /* UFS_REF_CLK */
+ 0x004 0x0 /* UFS_RST_N */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_08MA DRIVE6_MASK
+ >;
+ };
+
+ spi3_cfg_func: spi3_cfg_func {
+ pinctrl-single,pins = <
+ 0x008 0x0 /* SPI3_CLK */
+ 0x0 /* SPI3_DI */
+ 0x010 0x0 /* SPI3_DO */
+ 0x014 0x0 /* SPI3_CS0_N */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+ };
+
+ pmx7: pinmux@ff3fd800 {
+ compatible = "pinconf-single";
+ reg = <0x0 0xff3fd800 0x0 0x18>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <0x20>;
+
+ sdio_clk_cfg_func: sdio_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x000 0x0 /* SDIO_CLK */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_32MA DRIVE6_MASK
+ >;
+ };
+
+ sdio_cfg_func: sdio_cfg_func {
+ pinctrl-single,pins = <
+ 0x004 0x0 /* SDIO_CMD */
+ 0x008 0x0 /* SDIO_DATA0 */
+ 0x00c 0x0 /* SDIO_DATA1 */
+ 0x010 0x0 /* SDIO_DATA2 */
+ 0x014 0x0 /* SDIO_DATA3 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_19MA DRIVE6_MASK
+ >;
+ };
+ };
+
+ pmx8: pinmux@ff37e800 {
+ compatible = "pinconf-single";
+ reg = <0x0 0xff37e800 0x0 0x18>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <0x20>;
+
+ sd_clk_cfg_func: sd_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x000 0x0 /* SD_CLK */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_32MA
+ DRIVE6_MASK
+ >;
+ };
+
+ sd_cfg_func: sd_cfg_func {
+ pinctrl-single,pins = <
+ 0x004 0x0 /* SD_CMD */
+ 0x008 0x0 /* SD_DATA0 */
+ 0x00c 0x0 /* SD_DATA1 */
+ 0x010 0x0 /* SD_DATA2 */
+ 0x014 0x0 /* SD_DATA3 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_19MA
+ DRIVE6_MASK
+ >;
+ };
+ };
+
+ pmx9: pinmux@fff11800 {
+ compatible = "pinconf-single";
+ reg = <0x0 0xfff11800 0x0 0xbc>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <0x20>;
+
+ i2c0_cfg_func: i2c0_cfg_func {
+ pinctrl-single,pins = <
+ 0x01c 0x0 /* I2C0_SCL */
+ 0x020 0x0 /* I2C0_SDA */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ i2c1_cfg_func: i2c1_cfg_func {
+ pinctrl-single,pins = <
+ 0x024 0x0 /* I2C1_SCL */
+ 0x028 0x0 /* I2C1_SDA */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ i2c7_cfg_func: i2c7_cfg_func {
+ pinctrl-single,pins = <
+ 0x02c 0x0 /* I2C7_SCL */
+ 0x030 0x0 /* I2C7_SDA */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ slimbus_cfg_func: slimbus_cfg_func {
+ pinctrl-single,pins = <
+ 0x034 0x0 /* SLIMBUS_CLK */
+ 0x038 0x0 /* SLIMBUS_DATA */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ i2s0_cfg_func: i2s0_cfg_func {
+ pinctrl-single,pins = <
+ 0x040 0x0 /* I2S0_DI */
+ 0x044 0x0 /* I2S0_DO */
+ 0x048 0x0 /* I2S0_XCLK */
+ 0x04c 0x0 /* I2S0_XFS */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ i2s2_cfg_func: i2s2_cfg_func {
+ pinctrl-single,pins = <
+ 0x050 0x0 /* I2S2_DI */
+ 0x054 0x0 /* I2S2_DO */
+ 0x058 0x0 /* I2S2_XCLK */
+ 0x05c 0x0 /* I2S2_XFS */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ pcie_cfg_func: pcie_cfg_func {
+ pinctrl-single,pins = <
+ 0x094 0x0 /* PCIE_CLKREQ_N */
+ 0x098 0x0 /* PCIE_WAKE_N */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ spi2_cfg_func: spi2_cfg_func {
+ pinctrl-single,pins = <
+ 0x09c 0x0 /* SPI2_CLK */
+ 0x0a0 0x0 /* SPI2_DI */
+ 0x0a4 0x0 /* SPI2_DO */
+ 0x0a8 0x0 /* SPI2_CS0_N */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
+ >;
+ };
+
+ usb_cfg_func: usb_cfg_func {
+ pinctrl-single,pins = <
+ 0x0ac 0x0 /* GPIO_219 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE7_02MA DRIVE6_MASK
>;
};
};
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 04/12] arm64: dts: hi3660: add resources for clock and reset
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (2 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 03/12] arm64: dts: hikey960: pinctrl: add more pinmux and pinconfig Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 05/12] arm64: dts: Add I2C nodes for Hi3660 Guodong Xu
` (7 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel
From: Zhangfei Gao <zhangfei.gao@linaro.org>
Add some resource nodes for clock and reset
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 53 +++++++++++++++++++++++++++----
1 file changed, 46 insertions(+), 7 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 3983086..f55710a 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -5,6 +5,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/hi3660-clock.h>
/ {
compatible = "hisilicon,hi3660";
@@ -141,18 +142,56 @@
#size-cells = <2>;
ranges;
- fixed_uart5: fixed_19_2M {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <19200000>;
- clock-output-names = "fixed:uart5";
+ crg_ctrl: crg_ctrl@fff35000 {
+ compatible = "hisilicon,hi3660-crgctrl", "syscon";
+ reg = <0x0 0xfff35000 0x0 0x1000>;
+ #clock-cells = <1>;
};
- uart5: uart@fdf05000 {
+ crg_rst: crg_rst_controller {
+ compatible = "hisilicon,hi3660-reset";
+ #reset-cells = <2>;
+ hisi,rst-syscon = <&crg_ctrl>;
+ };
+
+
+ pctrl: pctrl@e8a09000 {
+ compatible = "hisilicon,hi3660-pctrl", "syscon";
+ reg = <0x0 0xe8a09000 0x0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+ pmuctrl: crg_ctrl@fff34000 {
+ compatible = "hisilicon,hi3660-pmuctrl", "syscon";
+ reg = <0x0 0xfff34000 0x0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ sctrl: sctrl@fff0a000 {
+ compatible = "hisilicon,hi3660-sctrl", "syscon";
+ reg = <0x0 0xfff0a000 0x0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ iomcu: iomcu@ffd7e000 {
+ compatible = "hisilicon,hi3660-iomcu", "syscon";
+ reg = <0x0 0xffd7e000 0x0 0x1000>;
+ #clock-cells = <1>;
+
+ };
+
+ iomcu_rst: reset {
+ compatible = "hisilicon,hi3660-reset";
+ hisi,rst-syscon = <&iomcu>;
+ #reset-cells = <2>;
+ };
+
+ uart5: serial@fdf05000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xfdf05000 0x0 0x1000>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&fixed_uart5 &fixed_uart5>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_UART5>,
+ <&crg_ctrl HI3660_CLK_GATE_UART5>;
clock-names = "uartclk", "apb_pclk";
status = "disabled";
};
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 05/12] arm64: dts: Add I2C nodes for Hi3660
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (3 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 04/12] arm64: dts: hi3660: add resources for clock and reset Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 06/12] arm64: dts: hi3660: add gpio dtsi file for Hisilicon Hi3660 SOC Guodong Xu
` (6 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel,
Jarkko Nikula, Guodong Xu
From: Zhangfei Gao <zhangfei.gao@linaro.org>
Add I2C nodes for Hi3660-hikey960.
On HiKey960,
I2C0, I2C7 are connected to Low Speed Expansion Connector.
I2C1 is connected to ADV7535.
I2C3 is connected to USB5734.
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 22 +++++++++
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 56 +++++++++++++++++++++++
2 files changed, 78 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index 64875a5..1a4d6c5 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -29,6 +29,28 @@
};
};
+&i2c0 {
+ /* On Low speed expansion */
+ label = "LS-I2C0";
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ adv7533: adv7533@39 {
+ status = "ok";
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+ };
+};
+
+&i2c7 {
+ /* On Low speed expansion */
+ label = "LS-I2C1";
+ status = "okay";
+};
+
&uart5 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index f55710a..9abe84e 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -186,6 +186,62 @@
#reset-cells = <2>;
};
+ i2c0: i2c@ffd71000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xffd71000 0x0 0x1000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <400000>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_I2C0>;
+ resets = <&iomcu_rst 0x20 3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pmx_func &i2c0_cfg_func>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@ffd72000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xffd72000 0x0 0x1000>;
+ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <400000>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_I2C1>;
+ resets = <&iomcu_rst 0x20 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pmx_func &i2c1_cfg_func>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@fdf0c000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xfdf0c000 0x0 0x1000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <400000>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_I2C3>;
+ resets = <&crg_rst 0x78 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pmx_func &i2c3_cfg_func>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@fdf0b000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0xfdf0b000 0x0 0x1000>;
+ interrupts = <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <400000>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_I2C7>;
+ resets = <&crg_rst 0x60 14>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_pmx_func &i2c7_cfg_func>;
+ status = "disabled";
+ };
+
uart5: serial@fdf05000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xfdf05000 0x0 0x1000>;
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 06/12] arm64: dts: hi3660: add gpio dtsi file for Hisilicon Hi3660 SOC
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (4 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 05/12] arm64: dts: Add I2C nodes for Hi3660 Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 07/12] arm64: dts: hi3660: Add uarts nodes Guodong Xu
` (5 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel, Wang Xiaoyin
From: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
This patch adds pl061 device nodes for Hi3660 SoC.
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 380 ++++++++++++++++++++++++++++++
1 file changed, 380 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 9abe84e..b03be4d 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -251,5 +251,385 @@
clock-names = "uartclk", "apb_pclk";
status = "disabled";
};
+
+ gpio0: gpio@e8a0b000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a0b000 0 0x1000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 1 0 7>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO0>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio1: gpio@e8a0c000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a0c000 0 0x1000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 1 7 7>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO1>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio2: gpio@e8a0d000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a0d000 0 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 14 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO2>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio3: gpio@e8a0e000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a0e000 0 0x1000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 22 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO3>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio4: gpio@e8a0f000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a0f000 0 0x1000>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 30 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO4>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio5: gpio@e8a10000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a10000 0 0x1000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 38 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO5>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio6: gpio@e8a11000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a11000 0 0x1000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 46 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO6>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio7: gpio@e8a12000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a12000 0 0x1000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 54 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO7>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio8: gpio@e8a13000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a13000 0 0x1000>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 62 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO8>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio9: gpio@e8a14000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a14000 0 0x1000>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 70 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO9>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio10: gpio@e8a15000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a15000 0 0x1000>;
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 78 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO10>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio11: gpio@e8a16000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a16000 0 0x1000>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 86 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO11>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio12: gpio@e8a17000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a17000 0 0x1000>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 94 3 &pmx0 7 101 1>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO12>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio13: gpio@e8a18000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a18000 0 0x1000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 102 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO13>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio14: gpio@e8a19000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a19000 0 0x1000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 110 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO14>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio15: gpio@e8a1a000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a1a000 0 0x1000>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx0 0 118 6>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO15>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio16: gpio@e8a1b000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a1b000 0 0x1000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO16>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio17: gpio@e8a1c000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a1c000 0 0x1000>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO17>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio18: gpio@ff3b4000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xff3b4000 0 0x1000>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx2 0 0 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO18>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio19: gpio@ff3b5000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xff3b5000 0 0x1000>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx2 0 8 4>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO19>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio20: gpio@e8a1f000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a1f000 0 0x1000>;
+ interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pmx1 0 0 6>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO20>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio21: gpio@e8a20000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xe8a20000 0 0x1000>;
+ interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&pmx3 0 0 6>;
+ clocks = <&crg_ctrl HI3660_PCLK_GPIO21>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio22: gpio@fff0b000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff0b000 0 0x1000>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* GPIO176 */
+ gpio-ranges = <&pmx4 2 0 6>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO0>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio23: gpio@fff0c000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff0c000 0 0x1000>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* GPIO184 */
+ gpio-ranges = <&pmx4 0 6 7>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO1>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio24: gpio@fff0d000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff0d000 0 0x1000>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* GPIO192 */
+ gpio-ranges = <&pmx4 0 13 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO2>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio25: gpio@fff0e000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff0e000 0 0x1000>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* GPIO200 */
+ gpio-ranges = <&pmx4 0 21 4 &pmx4 5 25 3>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO3>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio26: gpio@fff0f000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff0f000 0 0x1000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* GPIO208 */
+ gpio-ranges = <&pmx4 0 28 8>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO4>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio27: gpio@fff10000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff10000 0 0x1000>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* GPIO216 */
+ gpio-ranges = <&pmx4 0 36 6>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO5>;
+ clock-names = "apb_pclk";
+ };
+
+ gpio28: gpio@fff1d000 {
+ compatible = "arm,pl061", "arm,primecell";
+ reg = <0 0xfff1d000 0 0x1000>;
+ interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&sctrl HI3660_PCLK_AO_GPIO6>;
+ clock-names = "apb_pclk";
+ };
};
};
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 07/12] arm64: dts: hi3660: Add uarts nodes
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (5 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 06/12] arm64: dts: hi3660: add gpio dtsi file for Hisilicon Hi3660 SOC Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 08/12] arm64: dts: hikey960: add WL1837 Bluetooth device node Guodong Xu
` (4 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel,
Wang Xiaoyin, Guodong Xu
From: Chen Feng <puck.chen@hisilicon.com>
Add nodes uart0 to uart4 and uart6 for hi3660 SoC.
Enable uart3 and uart6, disable uart5, in hikey960 board dts.
On HiKey960:
- UART6 is used as default console, and is wired out through low speed
expansion connector.
- UART3 has RTS/CTS hardware handshake, and is wired out through low
speed expansion connector.
- UART5 is not used in commercial launched boards. So disable it.
- UART4 is connected to Bluetooth, WL1837.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 20 +++++-
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 74 +++++++++++++++++++++++
2 files changed, 91 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index 1a4d6c5..0a3f2e0 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -15,11 +15,17 @@
compatible = "hisilicon,hi3660-hikey960", "hisilicon,hi3660";
aliases {
- serial5 = &uart5; /* console UART */
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ serial4 = &uart4;
+ serial5 = &uart5;
+ serial6 = &uart6;
};
chosen {
- stdout-path = "serial5:115200n8";
+ stdout-path = "serial6:115200n8";
};
memory@0 {
@@ -51,6 +57,14 @@
status = "okay";
};
-&uart5 {
+&uart3 {
+ /* On Low speed expansion */
+ label = "LS-UART0";
+ status = "okay";
+};
+
+&uart6 {
+ /* On Low speed expansion */
+ label = "LS-UART1";
status = "okay";
};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index b03be4d..7a90c92 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -242,6 +242,66 @@
status = "disabled";
};
+ uart0: serial@fdf02000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf02000 0x0 0x1000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>,
+ <&crg_ctrl HI3660_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
+ status = "disabled";
+ };
+
+ uart1: serial@fdf00000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf00000 0x0 0x1000>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_UART1>,
+ <&crg_ctrl HI3660_CLK_GATE_UART1>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
+ status = "disabled";
+ };
+
+ uart2: serial@fdf03000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf03000 0x0 0x1000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_UART2>,
+ <&crg_ctrl HI3660_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
+ status = "disabled";
+ };
+
+ uart3: serial@ffd74000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xffd74000 0x0 0x1000>;
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_FACTOR_UART3>,
+ <&crg_ctrl HI3660_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
+ status = "disabled";
+ };
+
+ uart4: serial@fdf01000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf01000 0x0 0x1000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_UART4>,
+ <&crg_ctrl HI3660_CLK_GATE_UART4>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
+ status = "disabled";
+ };
+
uart5: serial@fdf05000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xfdf05000 0x0 0x1000>;
@@ -249,6 +309,20 @@
clocks = <&crg_ctrl HI3660_CLK_GATE_UART5>,
<&crg_ctrl HI3660_CLK_GATE_UART5>;
clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5_pmx_func &uart5_cfg_func>;
+ status = "disabled";
+ };
+
+ uart6: serial@fff32000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfff32000 0x0 0x1000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_UART6>,
+ <&crg_ctrl HI3660_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart6_pmx_func &uart6_cfg_func>;
status = "disabled";
};
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 08/12] arm64: dts: hikey960: add WL1837 Bluetooth device node
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (6 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 07/12] arm64: dts: hi3660: Add uarts nodes Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 09/12] arm64: dts: hi3660: Add pl031 rtc node Guodong Xu
` (3 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel, Guodong Xu
This adds the serial slave device for the WL1837 Bluetooth interface.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index 0a3f2e0..c25fff9 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -9,6 +9,7 @@
#include "hi3660.dtsi"
#include "hikey960-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "HiKey960";
@@ -63,6 +64,16 @@
status = "okay";
};
+&uart4 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "ti,wl1837-st";
+ enable-gpios = <&gpio15 6 GPIO_ACTIVE_HIGH>;
+ max-speed = <921600>;
+ };
+};
+
&uart6 {
/* On Low speed expansion */
label = "LS-UART1";
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 09/12] arm64: dts: hi3660: Add pl031 rtc node
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (7 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 08/12] arm64: dts: hikey960: add WL1837 Bluetooth device node Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 10/12] arm64: dts: hi3660: add power key dts node Guodong Xu
` (2 subsequent siblings)
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel
From: Chen Feng <puck.chen@hisilicon.com>
Add dts node to enable pl031 rtc.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
---
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 7a90c92..3b2a3a7 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -326,6 +326,14 @@
status = "disabled";
};
+ rtc0: rtc@fff04000 {
+ compatible = "arm,pl031", "arm,primecell";
+ reg = <0x0 0Xfff04000 0x0 0x1000>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_PCLK>;
+ clock-names = "apb_pclk";
+ };
+
gpio0: gpio@e8a0b000 {
compatible = "arm,pl061", "arm,primecell";
reg = <0 0xe8a0b000 0 0x1000>;
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 10/12] arm64: dts: hi3660: add power key dts node
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (8 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 09/12] arm64: dts: hi3660: Add pl031 rtc node Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 11/12] arm64: dts: hikey960: add LED nodes Guodong Xu
2017-05-25 8:18 ` [PATCH v2 12/12] arm64: dts: hi3660: add spi device nodes Guodong Xu
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel,
Chen Jun, John Stultz, Guodong Xu
From: Chen Jun <chenjun14@huawei.com>
We use gpio_034 as power key on hikey960, and set gpio with pull-up
state, when key press the voltage on the gpio will come to lower, and
power key event will be reported.
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index c25fff9..7aac35b 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -10,6 +10,8 @@
#include "hi3660.dtsi"
#include "hikey960-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "HiKey960";
@@ -34,6 +36,19 @@
/* rewrite this at bootloader */
reg = <0x0 0x0 0x0 0x0>;
};
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key_pmx_func &pwr_key_cfg_func>;
+
+ power {
+ wakeup-source;
+ gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+ label = "GPIO Power";
+ linux,code = <KEY_POWER>;
+ };
+ };
};
&i2c0 {
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 11/12] arm64: dts: hikey960: add LED nodes
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (9 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 10/12] arm64: dts: hi3660: add power key dts node Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
2017-05-25 8:18 ` [PATCH v2 12/12] arm64: dts: hi3660: add spi device nodes Guodong Xu
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel, Guodong Xu
HiKey960 has four user LEDs, and two special purpose LEDs: WiFi and BT
respectively.
All of them are implemented as GPIO.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 48 +++++++++++++++++++++++
1 file changed, 48 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index 7aac35b..9ecf6c6 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -49,6 +49,54 @@
linux,code = <KEY_POWER>;
};
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led1 {
+ label = "user_led1";
+ /* gpio_150_user_led1 */
+ gpios = <&gpio18 6 0>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ user_led2 {
+ label = "user_led2";
+ /* gpio_151_user_led2 */
+ gpios = <&gpio18 7 0>;
+ linux,default-trigger = "mmc0";
+ };
+
+ user_led3 {
+ label = "user_led3";
+ /* gpio_189_user_led3 */
+ gpios = <&gpio23 5 0>;
+ default-state = "off";
+ };
+
+ user_led4 {
+ label = "user_led4";
+ /* gpio_190_user_led4 */
+ gpios = <&gpio23 6 0>;
+ linux,default-trigger = "cpu0";
+ };
+
+ wlan_active_led {
+ label = "wifi_active";
+ /* gpio_205_wifi_active */
+ gpios = <&gpio25 5 0>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ bt_active_led {
+ label = "bt_active";
+ gpios = <&gpio25 7 0>;
+ /* gpio_207_user_led1 */
+ linux,default-trigger = "hci0-power";
+ default-state = "off";
+ };
+ };
};
&i2c0 {
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v2 12/12] arm64: dts: hi3660: add spi device nodes
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
` (10 preceding siblings ...)
2017-05-25 8:18 ` [PATCH v2 11/12] arm64: dts: hikey960: add LED nodes Guodong Xu
@ 2017-05-25 8:18 ` Guodong Xu
11 siblings, 0 replies; 13+ messages in thread
From: Guodong Xu @ 2017-05-25 8:18 UTC (permalink / raw)
To: robh+dt, mark.rutland, xuwei5, catalin.marinas, will.deacon,
wangkefeng.wang, xuejiancheng, peter.griffin, puck.chen
Cc: zhangfei.gao, devicetree, linux-kernel, linux-arm-kernel,
Wang Xiaoyin, Guodong Xu
From: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Add spi2 and spi3 device nodes for hi3660, and enable them for hikey960.
On HiKey960:
- SPI2 is wired out through low speed expansion connector.
- SPI3 is wired out through high speed expansion connector.
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
---
arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 12 +++++++++
arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 30 +++++++++++++++++++++++
2 files changed, 42 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index 9ecf6c6..ca448f0 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -142,3 +142,15 @@
label = "LS-UART1";
status = "okay";
};
+
+&spi2 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+};
+
+&spi3 {
+ /* On High speed expansion */
+ label = "HS-SPI1";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 3b2a3a7..a6b91f1 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -713,5 +713,35 @@
clocks = <&sctrl HI3660_PCLK_AO_GPIO6>;
clock-names = "apb_pclk";
};
+
+ spi2: spi@ffd68000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0xffd68000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_SPI2>;
+ clock-names = "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pmx_func>;
+ num-cs = <1>;
+ cs-gpios = <&gpio27 2 0>;
+ status = "disabled";
+ };
+
+ spi3: spi@ff3b3000 {
+ compatible = "arm,pl022", "arm,primecell";
+ reg = <0x0 0xff3b3000 0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_GATE_SPI3>;
+ clock-names = "apb_pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pmx_func>;
+ num-cs = <1>;
+ cs-gpios = <&gpio18 5 0>;
+ status = "disabled";
+ };
};
};
--
2.10.2
^ permalink raw reply related [flat|nested] 13+ messages in thread
end of thread, other threads:[~2017-05-25 8:23 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-05-25 8:18 [PATCH v2 00/12] arm64: dts: hi3660: add device nodes Guodong Xu
2017-05-25 8:18 ` [PATCH v2 01/12] dt-bindings: arm: hisilicon: add bindings for HiKey960 board Guodong Xu
2017-05-25 8:18 ` [PATCH v2 02/12] arm64: dts: hisilicon: update compatible string for hikey960 Guodong Xu
2017-05-25 8:18 ` [PATCH v2 03/12] arm64: dts: hikey960: pinctrl: add more pinmux and pinconfig Guodong Xu
2017-05-25 8:18 ` [PATCH v2 04/12] arm64: dts: hi3660: add resources for clock and reset Guodong Xu
2017-05-25 8:18 ` [PATCH v2 05/12] arm64: dts: Add I2C nodes for Hi3660 Guodong Xu
2017-05-25 8:18 ` [PATCH v2 06/12] arm64: dts: hi3660: add gpio dtsi file for Hisilicon Hi3660 SOC Guodong Xu
2017-05-25 8:18 ` [PATCH v2 07/12] arm64: dts: hi3660: Add uarts nodes Guodong Xu
2017-05-25 8:18 ` [PATCH v2 08/12] arm64: dts: hikey960: add WL1837 Bluetooth device node Guodong Xu
2017-05-25 8:18 ` [PATCH v2 09/12] arm64: dts: hi3660: Add pl031 rtc node Guodong Xu
2017-05-25 8:18 ` [PATCH v2 10/12] arm64: dts: hi3660: add power key dts node Guodong Xu
2017-05-25 8:18 ` [PATCH v2 11/12] arm64: dts: hikey960: add LED nodes Guodong Xu
2017-05-25 8:18 ` [PATCH v2 12/12] arm64: dts: hi3660: add spi device nodes Guodong Xu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).