* [PATCH v3 00/10] Initial Allwinner R40 support
@ 2017-05-27 10:22 Icenowy Zheng
2017-05-27 10:22 ` [PATCH v3 01/10] arm: sunxi: add support for R40 SoC Icenowy Zheng
` (9 more replies)
0 siblings, 10 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:22 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
This is the first non-RFC version of this patchset, which added basical
support including I2C, UART and MMC to the mainline Linux.
The pinctrl driver of A20 is also merged into the one of A10 before
R40 support is added into the A10 driver.
Chen-Yu Tsai (2):
ARM: dts: sun8i: Add basic dtsi file for Allwinner R40
ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra
Icenowy Zheng (8):
arm: sunxi: add support for R40 SoC
pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs
pinctrl: sunxi: add A20 support to A10 driver
pinctrl: sunxi: drop dedicated A20 driver
dt-bindings: add compatible string for Allwinner R40 pinctrl
pinctrl: sunxi: add support of R40 to A10 pinctrl driver
dt-bindings: add compatible string for Allwinner R40 CCU
clk: sunxi-ng: support R40 SoC
Documentation/arm/sunxi/README | 6 +
Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
.../devicetree/bindings/clock/sunxi-ccu.txt | 1 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 157 +++
arch/arm/boot/dts/sun8i-r40.dtsi | 408 +++++++
arch/arm/mach-sunxi/sunxi.c | 1 +
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun8i-r40.c | 1153 ++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun8i-r40.h | 68 ++
drivers/pinctrl/sunxi/Kconfig | 6 +-
drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 449 ++++++--
drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c | 1056 ------------------
drivers/pinctrl/sunxi/pinctrl-sunxi.h | 3 +
include/dt-bindings/clock/sun8i-r40-ccu.h | 191 ++++
include/dt-bindings/reset/sun8i-r40-ccu.h | 129 +++
18 files changed, 2497 insertions(+), 1145 deletions(-)
create mode 100644 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
create mode 100644 arch/arm/boot/dts/sun8i-r40.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.h
delete mode 100644 drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c
create mode 100644 include/dt-bindings/clock/sun8i-r40-ccu.h
create mode 100644 include/dt-bindings/reset/sun8i-r40-ccu.h
--
2.12.2
^ permalink raw reply [flat|nested] 36+ messages in thread
* [PATCH v3 01/10] arm: sunxi: add support for R40 SoC
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
@ 2017-05-27 10:22 ` Icenowy Zheng
2017-05-28 14:57 ` Chen-Yu Tsai
2017-05-31 19:42 ` Rob Herring
2017-05-27 10:23 ` [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs Icenowy Zheng
` (8 subsequent siblings)
9 siblings, 2 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:22 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
Allwinner R40 is a new SoC, with Quad Core Cortex-A7 and peripherals
like A20.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Use V1.0 documents.
Documentation/arm/sunxi/README | 6 ++++++
Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
arch/arm/mach-sunxi/sunxi.c | 1 +
3 files changed, 8 insertions(+)
diff --git a/Documentation/arm/sunxi/README b/Documentation/arm/sunxi/README
index d7b1f016bd62..af56321137e8 100644
--- a/Documentation/arm/sunxi/README
+++ b/Documentation/arm/sunxi/README
@@ -75,6 +75,12 @@ SunXi family
+ Datasheet
http://linux-sunxi.org/File:Allwinner_V3s_Datasheet_V1.0.pdf
+ - Allwinner R40 (sun8i)
+ + Datasheet
+ https://github.com/tinalinux/docs/blob/r40-v1.y/R40_Datasheet_V1.0.pdf
+ + User Manual
+ https://github.com/tinalinux/docs/blob/r40-v1.y/Allwinner_R40_User_Manual_V1.0.pdf
+
* Quad ARM Cortex-A15, Quad ARM Cortex-A7 based SoCs
- Allwinner A80
+ Datasheet
diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index d2c46449b4eb..b3ffe6cf821a 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -14,6 +14,7 @@ using one of the following compatible strings:
allwinner,sun8i-a83t
allwinner,sun8i-h2-plus
allwinner,sun8i-h3
+ allwinner-sun8i-r40
allwinner,sun9i-a80
allwinner,sun50i-a64
nextthing,gr8
diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
index f44e3acb5c90..aea616759451 100644
--- a/arch/arm/mach-sunxi/sunxi.c
+++ b/arch/arm/mach-sunxi/sunxi.c
@@ -66,6 +66,7 @@ static const char * const sun8i_board_dt_compat[] = {
"allwinner,sun8i-h2-plus",
"allwinner,sun8i-h3",
"allwinner,sun8i-v3s",
+ "allwinner,sun8i-r40",
NULL,
};
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
2017-05-27 10:22 ` [PATCH v3 01/10] arm: sunxi: add support for R40 SoC Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-28 14:58 ` Chen-Yu Tsai
2017-05-29 16:33 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver Icenowy Zheng
` (7 subsequent siblings)
9 siblings, 2 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
Allwinner A10, A20 and R40 SoCs have similar GPIO layout.
Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support
into A10 driver, and add R40 support into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Commit message change.
drivers/pinctrl/sunxi/pinctrl-sunxi.h | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.h b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
index a9d315a1256c..1bfc0d8a55df 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.h
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.h
@@ -87,6 +87,9 @@
#define PINCTRL_SUN5I_GR8 BIT(3)
#define PINCTRL_SUN6I_A31 BIT(4)
#define PINCTRL_SUN6I_A31S BIT(5)
+#define PINCTRL_SUN4I_A10 BIT(6)
+#define PINCTRL_SUN7I_A20 BIT(7)
+#define PINCTRL_SUN8I_R40 BIT(8)
struct sunxi_desc_function {
unsigned long variant;
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
2017-05-27 10:22 ` [PATCH v3 01/10] arm: sunxi: add support for R40 SoC Icenowy Zheng
2017-05-27 10:23 ` [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-28 15:06 ` Chen-Yu Tsai
2017-05-29 16:35 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver Icenowy Zheng
` (6 subsequent siblings)
9 siblings, 2 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
As A20 is designed as a pin-compatible upgrade of A10, their pin
controller are very similar, and can share one driver.
Add A20 support to the A10 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Enable A10 driver for A20 and disable A20 driver in this commit, in
order to prevent A10 driver from conflicting with A20 driver.
drivers/pinctrl/sunxi/Kconfig | 4 +-
drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 287 +++++++++++++++++++++++-------
2 files changed, 226 insertions(+), 65 deletions(-)
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 793e6f94fa0b..8224932e77a6 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -7,7 +7,7 @@ config PINCTRL_SUNXI
select GPIOLIB
config PINCTRL_SUN4I_A10
- def_bool MACH_SUN4I
+ def_bool MACH_SUN4I || MACH_SUN7I
select PINCTRL_SUNXI
config PINCTRL_SUN5I
@@ -24,7 +24,7 @@ config PINCTRL_SUN6I_A31_R
select PINCTRL_SUNXI
config PINCTRL_SUN7I_A20
- def_bool MACH_SUN7I
+ bool
select PINCTRL_SUNXI
config PINCTRL_SUN8I_A23
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
index fb30b86a97ee..159580c04b14 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
@@ -24,101 +24,147 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXD3 */
SUNXI_FUNCTION(0x3, "spi1"), /* CS0 */
- SUNXI_FUNCTION(0x4, "uart2")), /* RTS */
+ SUNXI_FUNCTION(0x4, "uart2"), /* RTS */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD3 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXD2 */
SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
- SUNXI_FUNCTION(0x4, "uart2")), /* CTS */
+ SUNXI_FUNCTION(0x4, "uart2"), /* CTS */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD2 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXD1 */
SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
- SUNXI_FUNCTION(0x4, "uart2")), /* TX */
+ SUNXI_FUNCTION(0x4, "uart2"), /* TX */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD1 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXD0 */
SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
- SUNXI_FUNCTION(0x4, "uart2")), /* RX */
+ SUNXI_FUNCTION(0x4, "uart2"), /* RX */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD0 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD3 */
- SUNXI_FUNCTION(0x3, "spi1")), /* CS1 */
+ SUNXI_FUNCTION(0x3, "spi1"), /* CS1 */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD3 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD2 */
- SUNXI_FUNCTION(0x3, "spi3")), /* CS0 */
+ SUNXI_FUNCTION(0x3, "spi3"), /* CS0 */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD2 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD1 */
- SUNXI_FUNCTION(0x3, "spi3")), /* CLK */
+ SUNXI_FUNCTION(0x3, "spi3"), /* CLK */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD1 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD0 */
- SUNXI_FUNCTION(0x3, "spi3")), /* MOSI */
+ SUNXI_FUNCTION(0x3, "spi3"), /* MOSI */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD0 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXCK */
- SUNXI_FUNCTION(0x3, "spi3")), /* MISO */
+ SUNXI_FUNCTION(0x3, "spi3"), /* MISO */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXCK */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXERR */
- SUNXI_FUNCTION(0x3, "spi3")), /* CS1 */
+ SUNXI_FUNCTION(0x3, "spi3"), /* CS1 */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ERXERR */
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* MCLK */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXDV */
- SUNXI_FUNCTION(0x4, "uart1")), /* TX */
+ SUNXI_FUNCTION(0x4, "uart1"), /* TX */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXDV */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* EMDC */
- SUNXI_FUNCTION(0x4, "uart1")), /* RX */
+ SUNXI_FUNCTION(0x4, "uart1"), /* RX */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* EMDC */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* EMDIO */
SUNXI_FUNCTION(0x3, "uart6"), /* TX */
- SUNXI_FUNCTION(0x4, "uart1")), /* RTS */
+ SUNXI_FUNCTION(0x4, "uart1"), /* RTS */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* EMDIO */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXEN */
SUNXI_FUNCTION(0x3, "uart6"), /* RX */
- SUNXI_FUNCTION(0x4, "uart1")), /* CTS */
+ SUNXI_FUNCTION(0x4, "uart1"), /* CTS */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXCTL / ETXEN */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXCK */
SUNXI_FUNCTION(0x3, "uart7"), /* TX */
- SUNXI_FUNCTION(0x4, "uart1")), /* DTR */
+ SUNXI_FUNCTION(0x4, "uart1"), /* DTR */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXCK */
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* BCLK */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ECRS */
SUNXI_FUNCTION(0x3, "uart7"), /* RX */
- SUNXI_FUNCTION(0x4, "uart1")), /* DSR */
+ SUNXI_FUNCTION(0x4, "uart1"), /* DSR */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXCK / ECRS */
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* LRCK */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ECOL */
SUNXI_FUNCTION(0x3, "can"), /* TX */
- SUNXI_FUNCTION(0x4, "uart1")), /* DCD */
+ SUNXI_FUNCTION(0x4, "uart1"), /* DCD */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GCLKIN / ECOL */
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DO */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXERR */
SUNXI_FUNCTION(0x3, "can"), /* RX */
- SUNXI_FUNCTION(0x4, "uart1")), /* RING */
+ SUNXI_FUNCTION(0x4, "uart1"), /* RING */
+ SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXERR */
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DI */
+ PINCTRL_SUN7I_A20)),
/* Hole */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -150,47 +196,77 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s"), /* MCLK */
+ /*
+ * On A10 there's only one I2S controller and the pin group
+ * is simply named "i2s". On A20 there's two and thus it's
+ * renamed to "i2s0". Deal with these name here, in order
+ * to satisfy existing device trees.
+ */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* MCLK */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* MCLK */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s"), /* BCLK */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* BCLK */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* BCLK */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x3, "ac97")), /* BCLK */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s"), /* LRCK */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* LRCK */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* LRCK */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x3, "ac97")), /* SYNC */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s"), /* DO0 */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO0 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO0 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x3, "ac97")), /* DO */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s")), /* DO1 */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO1 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO1 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s")), /* DO2 */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO2 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO2 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s")), /* DO3 */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO3 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO3 */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s"), /* DI */
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DI */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DI */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x3, "ac97"), /* DI */
- /* Undocumented mux function - See SPDIF MCLK above */
+ /* Undocumented mux function on A10 - See SPDIF MCLK above */
SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF IN */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "spi2"), /* CS1 */
- /* Undocumented mux function - See SPDIF MCLK above */
+ /* Undocumented mux function on A10 - See SPDIF MCLK above */
SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF OUT */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 14),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -672,7 +748,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D0 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAA0 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAA0 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart3"), /* TX */
SUNXI_FUNCTION_IRQ(0x6, 0), /* EINT0 */
SUNXI_FUNCTION(0x7, "csi1")), /* D0 */
@@ -680,7 +757,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D1 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAA1 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAA1 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart3"), /* RX */
SUNXI_FUNCTION_IRQ(0x6, 1), /* EINT1 */
SUNXI_FUNCTION(0x7, "csi1")), /* D1 */
@@ -688,7 +766,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D2 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAA2 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAA2 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
SUNXI_FUNCTION_IRQ(0x6, 2), /* EINT2 */
SUNXI_FUNCTION(0x7, "csi1")), /* D2 */
@@ -696,7 +775,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D3 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAIRQ */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIRQ */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
SUNXI_FUNCTION_IRQ(0x6, 3), /* EINT3 */
SUNXI_FUNCTION(0x7, "csi1")), /* D3 */
@@ -704,7 +784,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D4 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD0 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD0 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart4"), /* TX */
SUNXI_FUNCTION_IRQ(0x6, 4), /* EINT4 */
SUNXI_FUNCTION(0x7, "csi1")), /* D4 */
@@ -712,7 +793,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D5 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD1 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD1 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart4"), /* RX */
SUNXI_FUNCTION_IRQ(0x6, 5), /* EINT5 */
SUNXI_FUNCTION(0x7, "csi1")), /* D5 */
@@ -720,7 +802,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D6 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD2 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD2 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart5"), /* TX */
SUNXI_FUNCTION(0x5, "ms"), /* BS */
SUNXI_FUNCTION_IRQ(0x6, 6), /* EINT6 */
@@ -729,7 +812,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D7 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD3 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD3 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart5"), /* RX */
SUNXI_FUNCTION(0x5, "ms"), /* CLK */
SUNXI_FUNCTION_IRQ(0x6, 7), /* EINT7 */
@@ -738,7 +822,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D8 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD4 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD4 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD3 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN0 */
SUNXI_FUNCTION(0x5, "ms"), /* D0 */
SUNXI_FUNCTION_IRQ(0x6, 8), /* EINT8 */
@@ -747,7 +834,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D9 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD5 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD5 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD2 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN1 */
SUNXI_FUNCTION(0x5, "ms"), /* D1 */
SUNXI_FUNCTION_IRQ(0x6, 9), /* EINT9 */
@@ -756,7 +846,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D10 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD6 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD6 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD1 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN2 */
SUNXI_FUNCTION(0x5, "ms"), /* D2 */
SUNXI_FUNCTION_IRQ(0x6, 10), /* EINT10 */
@@ -765,7 +858,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D11 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD7 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD7 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD0 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN3 */
SUNXI_FUNCTION(0x5, "ms"), /* D3 */
SUNXI_FUNCTION_IRQ(0x6, 11), /* EINT11 */
@@ -774,7 +870,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D12 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD8 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD8 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "ps2"), /* SCK1 */
SUNXI_FUNCTION_IRQ(0x6, 12), /* EINT12 */
SUNXI_FUNCTION(0x7, "csi1")), /* D12 */
@@ -782,7 +879,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D13 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD9 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD9 */
+ PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "ps2"), /* SDA1 */
SUNXI_FUNCTION(0x5, "sim"), /* RST */
SUNXI_FUNCTION_IRQ(0x6, 13), /* EINT13 */
@@ -791,7 +889,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D14 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD10 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD10 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD3 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN4 */
SUNXI_FUNCTION(0x5, "sim"), /* VPPEN */
SUNXI_FUNCTION_IRQ(0x6, 14), /* EINT14 */
@@ -800,7 +901,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D15 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD11 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD11 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD2 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN5 */
SUNXI_FUNCTION(0x5, "sim"), /* VPPPP */
SUNXI_FUNCTION_IRQ(0x6, 15), /* EINT15 */
@@ -809,7 +913,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D16 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD12 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD12 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD1 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
@@ -817,7 +924,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D17 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD13 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD13 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD0 */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* IN7 */
SUNXI_FUNCTION(0x5, "sim"), /* VCCEN */
SUNXI_FUNCTION_IRQ(0x6, 17), /* EINT17 */
@@ -826,7 +936,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D18 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD14 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD14 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXCK */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT0 */
SUNXI_FUNCTION(0x5, "sim"), /* SCK */
SUNXI_FUNCTION_IRQ(0x6, 18), /* EINT18 */
@@ -835,7 +948,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D19 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAD15 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD15 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXERR */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT1 */
SUNXI_FUNCTION(0x5, "sim"), /* SDA */
SUNXI_FUNCTION_IRQ(0x6, 19), /* EINT19 */
@@ -844,7 +960,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D20 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAOE */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAOE */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXDV */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "can"), /* TX */
SUNXI_FUNCTION_IRQ(0x6, 20), /* EINT20 */
SUNXI_FUNCTION(0x7, "csi1")), /* D20 */
@@ -852,7 +971,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D21 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATADREQ */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATADREQ */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* EMDC */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "can"), /* RX */
SUNXI_FUNCTION_IRQ(0x6, 21), /* EINT21 */
SUNXI_FUNCTION(0x7, "csi1")), /* D21 */
@@ -860,7 +982,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D22 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATADACK */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATADACK */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* EMDIO */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT2 */
SUNXI_FUNCTION(0x5, "mmc1"), /* CMD */
SUNXI_FUNCTION(0x7, "csi1")), /* D22 */
@@ -868,7 +993,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* D23 */
- SUNXI_FUNCTION(0x3, "pata"), /* ATACS0 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATACS0 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXEN */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT3 */
SUNXI_FUNCTION(0x5, "mmc1"), /* CLK */
SUNXI_FUNCTION(0x7, "csi1")), /* D23 */
@@ -876,7 +1004,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* CLK */
- SUNXI_FUNCTION(0x3, "pata"), /* ATACS1 */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATACS1 */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXCK */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT4 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D0 */
SUNXI_FUNCTION(0x7, "csi1")), /* PCLK */
@@ -884,7 +1015,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* DE */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAIORDY */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIORDY */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ECRS */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT5 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D1 */
SUNXI_FUNCTION(0x7, "csi1")), /* FIELD */
@@ -892,7 +1026,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* HSYNC */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAIOR */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIOR */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ECOL */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT6 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D2 */
SUNXI_FUNCTION(0x7, "csi1")), /* HSYNC */
@@ -900,24 +1037,35 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "lcd1"), /* VSYNC */
- SUNXI_FUNCTION(0x3, "pata"), /* ATAIOW */
+ SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIOW */
+ PINCTRL_SUN4I_A10),
+ SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXERR */
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT7 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D3 */
SUNXI_FUNCTION(0x7, "csi1")), /* VSYNC */
/* Hole */
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 0),
SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out")),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_VARIANT(0x3, "i2c3", /* SCK */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 1),
SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out")),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_VARIANT(0x3, "i2c3", /* SDA */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 2),
SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out")),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_VARIANT(0x3, "i2c4", /* SCK */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "pwm")), /* PWM1 */
+ SUNXI_FUNCTION(0x2, "pwm"), /* PWM1 */
+ SUNXI_FUNCTION_VARIANT(0x3, "i2c3", /* SDA */
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 4),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -959,12 +1107,16 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "spi0"), /* MOSI */
SUNXI_FUNCTION(0x3, "uart6"), /* TX */
+ SUNXI_FUNCTION_VARIANT(0x4, "clk_out_a",
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 24)), /* EINT24 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "spi0"), /* MISO */
SUNXI_FUNCTION(0x3, "uart6"), /* RX */
+ SUNXI_FUNCTION_VARIANT(0x4, "clk_out_b",
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 25)), /* EINT25 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 14),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -1027,12 +1179,21 @@ static const struct sunxi_pinctrl_desc sun4i_a10_pinctrl_data = {
static int sun4i_a10_pinctrl_probe(struct platform_device *pdev)
{
- return sunxi_pinctrl_init(pdev,
- &sun4i_a10_pinctrl_data);
+ unsigned long variant = (unsigned long)of_device_get_match_data(&pdev->dev);
+
+ return sunxi_pinctrl_init_with_variant(pdev, &sun4i_a10_pinctrl_data,
+ variant);
}
static const struct of_device_id sun4i_a10_pinctrl_match[] = {
- { .compatible = "allwinner,sun4i-a10-pinctrl", },
+ {
+ .compatible = "allwinner,sun4i-a10-pinctrl",
+ .data = (void *)PINCTRL_SUN4I_A10
+ },
+ {
+ .compatible = "allwinner,sun7i-a20-pinctrl",
+ .data = (void *)PINCTRL_SUN7I_A20
+ },
{}
};
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (2 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-28 15:08 ` Chen-Yu Tsai
2017-05-29 16:39 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl Icenowy Zheng
` (5 subsequent siblings)
9 siblings, 2 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
As we added A20 support to A10 pinctrl driver, now we can delete the
dedicated A20 pinctrl driver, which is duplicated code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Only remove the A20 driver(A10 driver for A20 is enabled in
the previous commit now).
drivers/pinctrl/sunxi/Kconfig | 4 -
drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c | 1056 -----------------------------
2 files changed, 1060 deletions(-)
delete mode 100644 drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 8224932e77a6..624d84e6c936 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -23,10 +23,6 @@ config PINCTRL_SUN6I_A31_R
depends on RESET_CONTROLLER
select PINCTRL_SUNXI
-config PINCTRL_SUN7I_A20
- bool
- select PINCTRL_SUNXI
-
config PINCTRL_SUN8I_A23
def_bool MACH_SUN8I
select PINCTRL_SUNXI
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c b/drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c
deleted file mode 100644
index b6f4c68ffb39..000000000000
--- a/drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c
+++ /dev/null
@@ -1,1056 +0,0 @@
-/*
- * Allwinner A20 SoCs pinctrl driver.
- *
- * Copyright (C) 2014 Maxime Ripard
- *
- * Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/pinctrl/pinctrl.h>
-
-#include "pinctrl-sunxi.h"
-
-static const struct sunxi_desc_pin sun7i_a20_pins[] = {
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXD3 */
- SUNXI_FUNCTION(0x3, "spi1"), /* CS0 */
- SUNXI_FUNCTION(0x4, "uart2"), /* RTS */
- SUNXI_FUNCTION(0x5, "gmac")), /* GRXD3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXD2 */
- SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
- SUNXI_FUNCTION(0x4, "uart2"), /* CTS */
- SUNXI_FUNCTION(0x5, "gmac")), /* GRXD2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXD1 */
- SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
- SUNXI_FUNCTION(0x4, "uart2"), /* TX */
- SUNXI_FUNCTION(0x5, "gmac")), /* GRXD1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXD0 */
- SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
- SUNXI_FUNCTION(0x4, "uart2"), /* RX */
- SUNXI_FUNCTION(0x5, "gmac")), /* GRXD0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXD3 */
- SUNXI_FUNCTION(0x3, "spi1"), /* CS1 */
- SUNXI_FUNCTION(0x5, "gmac")), /* GTXD3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXD2 */
- SUNXI_FUNCTION(0x3, "spi3"), /* CS0 */
- SUNXI_FUNCTION(0x5, "gmac")), /* GTXD2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXD1 */
- SUNXI_FUNCTION(0x3, "spi3"), /* CLK */
- SUNXI_FUNCTION(0x5, "gmac")), /* GTXD1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXD0 */
- SUNXI_FUNCTION(0x3, "spi3"), /* MOSI */
- SUNXI_FUNCTION(0x5, "gmac")), /* GTXD0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXCK */
- SUNXI_FUNCTION(0x3, "spi3"), /* MISO */
- SUNXI_FUNCTION(0x5, "gmac")), /* GRXCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXERR */
- SUNXI_FUNCTION(0x3, "spi3"), /* CS1 */
- SUNXI_FUNCTION(0x5, "gmac"), /* GNULL / ERXERR */
- SUNXI_FUNCTION(0x6, "i2s1")), /* MCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ERXDV */
- SUNXI_FUNCTION(0x4, "uart1"), /* TX */
- SUNXI_FUNCTION(0x5, "gmac")), /* GRXCTL / ERXDV */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* EMDC */
- SUNXI_FUNCTION(0x4, "uart1"), /* RX */
- SUNXI_FUNCTION(0x5, "gmac")), /* EMDC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* EMDIO */
- SUNXI_FUNCTION(0x3, "uart6"), /* TX */
- SUNXI_FUNCTION(0x4, "uart1"), /* RTS */
- SUNXI_FUNCTION(0x5, "gmac")), /* EMDIO */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXEN */
- SUNXI_FUNCTION(0x3, "uart6"), /* RX */
- SUNXI_FUNCTION(0x4, "uart1"), /* CTS */
- SUNXI_FUNCTION(0x5, "gmac")), /* GTXCTL / ETXEN */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXCK */
- SUNXI_FUNCTION(0x3, "uart7"), /* TX */
- SUNXI_FUNCTION(0x4, "uart1"), /* DTR */
- SUNXI_FUNCTION(0x5, "gmac"), /* GNULL / ETXCK */
- SUNXI_FUNCTION(0x6, "i2s1")), /* BCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ECRS */
- SUNXI_FUNCTION(0x3, "uart7"), /* RX */
- SUNXI_FUNCTION(0x4, "uart1"), /* DSR */
- SUNXI_FUNCTION(0x5, "gmac"), /* GTXCK / ECRS */
- SUNXI_FUNCTION(0x6, "i2s1")), /* LRCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ECOL */
- SUNXI_FUNCTION(0x3, "can"), /* TX */
- SUNXI_FUNCTION(0x4, "uart1"), /* DCD */
- SUNXI_FUNCTION(0x5, "gmac"), /* GCLKIN / ECOL */
- SUNXI_FUNCTION(0x6, "i2s1")), /* DO */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "emac"), /* ETXERR */
- SUNXI_FUNCTION(0x3, "can"), /* RX */
- SUNXI_FUNCTION(0x4, "uart1"), /* RING */
- SUNXI_FUNCTION(0x5, "gmac"), /* GNULL / ETXERR */
- SUNXI_FUNCTION(0x6, "i2s1")), /* LRCK */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c0")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c0")), /* SDA */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "pwm")), /* PWM0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ir0"), /* TX */
- SUNXI_FUNCTION(0x4, "spdif")), /* MCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ir0")), /* RX */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0"), /* MCLK */
- SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0"), /* BCLK */
- SUNXI_FUNCTION(0x3, "ac97")), /* BCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0"), /* LRCK */
- SUNXI_FUNCTION(0x3, "ac97")), /* SYNC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0"), /* DO0 */
- SUNXI_FUNCTION(0x3, "ac97")), /* DO */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0")), /* DO1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0")), /* DO2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0")), /* DO3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2s0"), /* DI */
- SUNXI_FUNCTION(0x3, "ac97"), /* DI */
- SUNXI_FUNCTION(0x4, "spdif")), /* DI */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi2"), /* CS1 */
- SUNXI_FUNCTION(0x4, "spdif")), /* DO */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 14),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi2"), /* CS0 */
- SUNXI_FUNCTION(0x3, "jtag")), /* MS0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 15),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi2"), /* CLK */
- SUNXI_FUNCTION(0x3, "jtag")), /* CK0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 16),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi2"), /* MOSI */
- SUNXI_FUNCTION(0x3, "jtag")), /* DO0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 17),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi2"), /* MISO */
- SUNXI_FUNCTION(0x3, "jtag")), /* DI0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 18),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c1")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 19),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c1")), /* SDA */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 20),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c2")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 21),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c2")), /* SDA */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 22),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "uart0"), /* TX */
- SUNXI_FUNCTION(0x3, "ir1")), /* TX */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 23),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "uart0"), /* RX */
- SUNXI_FUNCTION(0x3, "ir1")), /* RX */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NWE */
- SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NALE */
- SUNXI_FUNCTION(0x3, "spi0")), /* MISO */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NCLE */
- SUNXI_FUNCTION(0x3, "spi0")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NCE1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NCE0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NRE# */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NRB0 */
- SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NRB1 */
- SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NDQ0 */
- SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NDQ1 */
- SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NDQ2 */
- SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NDQ3 */
- SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ4 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ5 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ6 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ7 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NWP */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 17),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NCE2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 18),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NCE3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 19),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NCE4 */
- SUNXI_FUNCTION(0x3, "spi2")), /* CS0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 20),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NCE5 */
- SUNXI_FUNCTION(0x3, "spi2")), /* CLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 21),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NCE6 */
- SUNXI_FUNCTION(0x3, "spi2")), /* MOSI */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 22),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0"), /* NCE7 */
- SUNXI_FUNCTION(0x3, "spi2")), /* MISO */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 23),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x3, "spi0")), /* CS0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 24),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQS */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D0 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VP0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D1 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VN0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D2 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VP1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D3 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VN1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D4 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VP2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D5 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VN2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D6 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VPC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D7 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VNC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D8 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VP3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D9 */
- SUNXI_FUNCTION(0x3, "lvds0")), /* VM3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D10 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VP0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D11 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VN0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D12 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VP1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D13 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VN1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D14 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VP2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D15 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VN2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D16 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VPC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D17 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VNC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D18 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VP3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D19 */
- SUNXI_FUNCTION(0x3, "lvds1")), /* VN3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D20 */
- SUNXI_FUNCTION(0x3, "csi1")), /* MCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D21 */
- SUNXI_FUNCTION(0x3, "sim")), /* VPPEN */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D22 */
- SUNXI_FUNCTION(0x3, "sim")), /* VPPPP */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* D23 */
- SUNXI_FUNCTION(0x3, "sim")), /* DET */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 24),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* CLK */
- SUNXI_FUNCTION(0x3, "sim")), /* VCCEN */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 25),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* DE */
- SUNXI_FUNCTION(0x3, "sim")), /* RST */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 26),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* HSYNC */
- SUNXI_FUNCTION(0x3, "sim")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 27),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd0"), /* VSYNC */
- SUNXI_FUNCTION(0x3, "sim")), /* SDA */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* CLK */
- SUNXI_FUNCTION(0x3, "csi0")), /* PCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* ERR */
- SUNXI_FUNCTION(0x3, "csi0")), /* CK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* SYNC */
- SUNXI_FUNCTION(0x3, "csi0")), /* HSYNC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* DVLD */
- SUNXI_FUNCTION(0x3, "csi0")), /* VSYNC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D0 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D1 */
- SUNXI_FUNCTION(0x3, "csi0"), /* D1 */
- SUNXI_FUNCTION(0x4, "sim")), /* VPPEN */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D2 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D3 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D4 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D4 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D5 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D5 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D6 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D6 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts0"), /* D7 */
- SUNXI_FUNCTION(0x3, "csi0")), /* D7 */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
- SUNXI_FUNCTION(0x4, "jtag")), /* MSI */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
- SUNXI_FUNCTION(0x4, "jtag")), /* DI1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
- SUNXI_FUNCTION(0x4, "uart0")), /* TX */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
- SUNXI_FUNCTION(0x4, "jtag")), /* DO1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
- SUNXI_FUNCTION(0x4, "uart0")), /* RX */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
- SUNXI_FUNCTION(0x4, "jtag")), /* CK1 */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* CLK */
- SUNXI_FUNCTION(0x3, "csi1"), /* PCK */
- SUNXI_FUNCTION(0x4, "mmc1")), /* CMD */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* ERR */
- SUNXI_FUNCTION(0x3, "csi1"), /* CK */
- SUNXI_FUNCTION(0x4, "mmc1")), /* CLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* SYNC */
- SUNXI_FUNCTION(0x3, "csi1"), /* HSYNC */
- SUNXI_FUNCTION(0x4, "mmc1")), /* D0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* DVLD */
- SUNXI_FUNCTION(0x3, "csi1"), /* VSYNC */
- SUNXI_FUNCTION(0x4, "mmc1")), /* D1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D0 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D0 */
- SUNXI_FUNCTION(0x4, "mmc1"), /* D2 */
- SUNXI_FUNCTION(0x5, "csi0")), /* D8 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D1 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D1 */
- SUNXI_FUNCTION(0x4, "mmc1"), /* D3 */
- SUNXI_FUNCTION(0x5, "csi0")), /* D9 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D2 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D2 */
- SUNXI_FUNCTION(0x4, "uart3"), /* TX */
- SUNXI_FUNCTION(0x5, "csi0")), /* D10 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D3 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D3 */
- SUNXI_FUNCTION(0x4, "uart3"), /* RX */
- SUNXI_FUNCTION(0x5, "csi0")), /* D11 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D4 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D4 */
- SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
- SUNXI_FUNCTION(0x5, "csi0")), /* D12 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D5 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D5 */
- SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
- SUNXI_FUNCTION(0x5, "csi0")), /* D13 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D6 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D6 */
- SUNXI_FUNCTION(0x4, "uart4"), /* TX */
- SUNXI_FUNCTION(0x5, "csi0")), /* D14 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ts1"), /* D7 */
- SUNXI_FUNCTION(0x3, "csi1"), /* D7 */
- SUNXI_FUNCTION(0x4, "uart4"), /* RX */
- SUNXI_FUNCTION(0x5, "csi0")), /* D15 */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D0 */
- SUNXI_FUNCTION(0x4, "uart3"), /* TX */
- SUNXI_FUNCTION_IRQ(0x6, 0), /* EINT0 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D1 */
- SUNXI_FUNCTION(0x4, "uart3"), /* RX */
- SUNXI_FUNCTION_IRQ(0x6, 1), /* EINT1 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D2 */
- SUNXI_FUNCTION(0x4, "uart3"), /* RTS */
- SUNXI_FUNCTION_IRQ(0x6, 2), /* EINT2 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D3 */
- SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
- SUNXI_FUNCTION_IRQ(0x6, 3), /* EINT3 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D4 */
- SUNXI_FUNCTION(0x4, "uart4"), /* TX */
- SUNXI_FUNCTION_IRQ(0x6, 4), /* EINT4 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D4 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D5 */
- SUNXI_FUNCTION(0x4, "uart4"), /* RX */
- SUNXI_FUNCTION_IRQ(0x6, 5), /* EINT5 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D5 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D6 */
- SUNXI_FUNCTION(0x4, "uart5"), /* TX */
- SUNXI_FUNCTION(0x5, "ms"), /* BS */
- SUNXI_FUNCTION_IRQ(0x6, 6), /* EINT6 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D6 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D7 */
- SUNXI_FUNCTION(0x4, "uart5"), /* RX */
- SUNXI_FUNCTION(0x5, "ms"), /* CLK */
- SUNXI_FUNCTION_IRQ(0x6, 7), /* EINT7 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D7 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D8 */
- SUNXI_FUNCTION(0x3, "emac"), /* ERXD3 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN0 */
- SUNXI_FUNCTION(0x5, "ms"), /* D0 */
- SUNXI_FUNCTION_IRQ(0x6, 8), /* EINT8 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D8 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D9 */
- SUNXI_FUNCTION(0x3, "emac"), /* ERXD2 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN1 */
- SUNXI_FUNCTION(0x5, "ms"), /* D1 */
- SUNXI_FUNCTION_IRQ(0x6, 9), /* EINT9 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D9 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D10 */
- SUNXI_FUNCTION(0x3, "emac"), /* ERXD1 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN2 */
- SUNXI_FUNCTION(0x5, "ms"), /* D2 */
- SUNXI_FUNCTION_IRQ(0x6, 10), /* EINT10 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D10 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D11 */
- SUNXI_FUNCTION(0x3, "emac"), /* ERXD0 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN3 */
- SUNXI_FUNCTION(0x5, "ms"), /* D3 */
- SUNXI_FUNCTION_IRQ(0x6, 11), /* EINT11 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D11 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D12 */
- SUNXI_FUNCTION(0x4, "ps2"), /* SCK1 */
- SUNXI_FUNCTION_IRQ(0x6, 12), /* EINT12 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D12 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 13),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D13 */
- SUNXI_FUNCTION(0x4, "ps2"), /* SDA1 */
- SUNXI_FUNCTION(0x5, "sim"), /* RST */
- SUNXI_FUNCTION_IRQ(0x6, 13), /* EINT13 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D13 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 14),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D14 */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXD3 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN4 */
- SUNXI_FUNCTION(0x5, "sim"), /* VPPEN */
- SUNXI_FUNCTION_IRQ(0x6, 14), /* EINT14 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D14 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 15),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D15 */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXD3 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN5 */
- SUNXI_FUNCTION(0x5, "sim"), /* VPPPP */
- SUNXI_FUNCTION_IRQ(0x6, 15), /* EINT15 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D15 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 16),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D16 */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXD2 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
- SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 17),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D17 */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXD1 */
- SUNXI_FUNCTION(0x4, "keypad"), /* IN7 */
- SUNXI_FUNCTION(0x5, "sim"), /* VCCEN */
- SUNXI_FUNCTION_IRQ(0x6, 17), /* EINT17 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D17 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 18),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D18 */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXD0 */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT0 */
- SUNXI_FUNCTION(0x5, "sim"), /* SCK */
- SUNXI_FUNCTION_IRQ(0x6, 18), /* EINT18 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D18 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 19),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D19 */
- SUNXI_FUNCTION(0x3, "emac"), /* ERXERR */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT1 */
- SUNXI_FUNCTION(0x5, "sim"), /* SDA */
- SUNXI_FUNCTION_IRQ(0x6, 19), /* EINT19 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D19 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 20),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D20 */
- SUNXI_FUNCTION(0x3, "emac"), /* ERXDV */
- SUNXI_FUNCTION(0x4, "can"), /* TX */
- SUNXI_FUNCTION_IRQ(0x6, 20), /* EINT20 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D20 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 21),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D21 */
- SUNXI_FUNCTION(0x3, "emac"), /* EMDC */
- SUNXI_FUNCTION(0x4, "can"), /* RX */
- SUNXI_FUNCTION_IRQ(0x6, 21), /* EINT21 */
- SUNXI_FUNCTION(0x7, "csi1")), /* D21 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 22),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D22 */
- SUNXI_FUNCTION(0x3, "emac"), /* EMDIO */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT2 */
- SUNXI_FUNCTION(0x5, "mmc1"), /* CMD */
- SUNXI_FUNCTION(0x7, "csi1")), /* D22 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 23),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* D23 */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXEN */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT3 */
- SUNXI_FUNCTION(0x5, "mmc1"), /* CLK */
- SUNXI_FUNCTION(0x7, "csi1")), /* D23 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 24),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* CLK */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXCK */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT4 */
- SUNXI_FUNCTION(0x5, "mmc1"), /* D0 */
- SUNXI_FUNCTION(0x7, "csi1")), /* PCLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 25),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* DE */
- SUNXI_FUNCTION(0x3, "emac"), /* ECRS */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT5 */
- SUNXI_FUNCTION(0x5, "mmc1"), /* D1 */
- SUNXI_FUNCTION(0x7, "csi1")), /* FIELD */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 26),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* HSYNC */
- SUNXI_FUNCTION(0x3, "emac"), /* ECOL */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT6 */
- SUNXI_FUNCTION(0x5, "mmc1"), /* D2 */
- SUNXI_FUNCTION(0x7, "csi1")), /* HSYNC */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 27),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "lcd1"), /* VSYNC */
- SUNXI_FUNCTION(0x3, "emac"), /* ETXERR */
- SUNXI_FUNCTION(0x4, "keypad"), /* OUT7 */
- SUNXI_FUNCTION(0x5, "mmc1"), /* D3 */
- SUNXI_FUNCTION(0x7, "csi1")), /* VSYNC */
- /* Hole */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 0),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x3, "i2c3")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 1),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x3, "i2c3")), /* SDA */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 2),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x3, "i2c4")), /* SCK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "pwm"), /* PWM1 */
- SUNXI_FUNCTION(0x3, "i2c4")), /* SDA */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 4),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc3")), /* CMD */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 5),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc3")), /* CLK */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 6),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc3")), /* D0 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 7),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc3")), /* D1 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 8),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc3")), /* D2 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 9),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "mmc3")), /* D3 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 10),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi0"), /* CS0 */
- SUNXI_FUNCTION(0x3, "uart5"), /* TX */
- SUNXI_FUNCTION_IRQ(0x6, 22)), /* EINT22 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 11),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi0"), /* CLK */
- SUNXI_FUNCTION(0x3, "uart5"), /* RX */
- SUNXI_FUNCTION_IRQ(0x6, 23)), /* EINT23 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 12),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi0"), /* MOSI */
- SUNXI_FUNCTION(0x3, "uart6"), /* TX */
- SUNXI_FUNCTION(0x4, "clk_out_a"), /* CLK_OUT_A */
- SUNXI_FUNCTION_IRQ(0x6, 24)), /* EINT24 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 13),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi0"), /* MISO */
- SUNXI_FUNCTION(0x3, "uart6"), /* RX */
- SUNXI_FUNCTION(0x4, "clk_out_b"), /* CLK_OUT_B */
- SUNXI_FUNCTION_IRQ(0x6, 25)), /* EINT25 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 14),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi0"), /* CS1 */
- SUNXI_FUNCTION(0x3, "ps2"), /* SCK1 */
- SUNXI_FUNCTION(0x4, "timer4"), /* TCLKIN0 */
- SUNXI_FUNCTION_IRQ(0x6, 26)), /* EINT26 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 15),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi1"), /* CS1 */
- SUNXI_FUNCTION(0x3, "ps2"), /* SDA1 */
- SUNXI_FUNCTION(0x4, "timer5"), /* TCLKIN1 */
- SUNXI_FUNCTION_IRQ(0x6, 27)), /* EINT27 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 16),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi1"), /* CS0 */
- SUNXI_FUNCTION(0x3, "uart2"), /* RTS */
- SUNXI_FUNCTION_IRQ(0x6, 28)), /* EINT28 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 17),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
- SUNXI_FUNCTION(0x3, "uart2"), /* CTS */
- SUNXI_FUNCTION_IRQ(0x6, 29)), /* EINT29 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 18),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
- SUNXI_FUNCTION(0x3, "uart2"), /* TX */
- SUNXI_FUNCTION_IRQ(0x6, 30)), /* EINT30 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 19),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
- SUNXI_FUNCTION(0x3, "uart2"), /* RX */
- SUNXI_FUNCTION_IRQ(0x6, 31)), /* EINT31 */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 20),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ps2"), /* SCK0 */
- SUNXI_FUNCTION(0x3, "uart7"), /* TX */
- SUNXI_FUNCTION(0x4, "hdmi")), /* HSCL */
- SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 21),
- SUNXI_FUNCTION(0x0, "gpio_in"),
- SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ps2"), /* SDA0 */
- SUNXI_FUNCTION(0x3, "uart7"), /* RX */
- SUNXI_FUNCTION(0x4, "hdmi")), /* HSDA */
-};
-
-static const struct sunxi_pinctrl_desc sun7i_a20_pinctrl_data = {
- .pins = sun7i_a20_pins,
- .npins = ARRAY_SIZE(sun7i_a20_pins),
- .irq_banks = 1,
-};
-
-static int sun7i_a20_pinctrl_probe(struct platform_device *pdev)
-{
- return sunxi_pinctrl_init(pdev,
- &sun7i_a20_pinctrl_data);
-}
-
-static const struct of_device_id sun7i_a20_pinctrl_match[] = {
- { .compatible = "allwinner,sun7i-a20-pinctrl", },
- {}
-};
-
-static struct platform_driver sun7i_a20_pinctrl_driver = {
- .probe = sun7i_a20_pinctrl_probe,
- .driver = {
- .name = "sun7i-a20-pinctrl",
- .of_match_table = sun7i_a20_pinctrl_match,
- },
-};
-builtin_platform_driver(sun7i_a20_pinctrl_driver);
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (3 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-28 15:09 ` Chen-Yu Tsai
2017-05-29 16:40 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver Icenowy Zheng
` (4 subsequent siblings)
9 siblings, 2 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
Allwinner R40 has a pin controller like the ones in older Allwinner SoCs
(especially A20), and can use modified version of the A10/A20 pinctrl
driver.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
---
Changes in v3:
- Added Rob's ACK.
Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index b53224473672..3ab9f7849a19 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -22,6 +22,7 @@ Required properties:
"allwinner,sun8i-a83t-pinctrl"
"allwinner,sun8i-h3-pinctrl"
"allwinner,sun8i-h3-r-pinctrl"
+ "allwinner,sun8i-r40-pinctrl"
"allwinner,sun50i-a64-pinctrl"
"allwinner,sun50i-a64-r-pinctrl"
"allwinner,sun50i-h5-pinctrl"
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (4 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-29 13:11 ` Chen-Yu Tsai
2017-05-29 16:43 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU Icenowy Zheng
` (3 subsequent siblings)
9 siblings, 2 replies; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
R40 is said to be an upgrade of A20, and its pin configuration is also
similar to A20 (and thus similar to A10).
Add support for R40 to the A10 pinctrl driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
drivers/pinctrl/sunxi/Kconfig | 2 +-
drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 272 +++++++++++++++++++++---------
2 files changed, 197 insertions(+), 77 deletions(-)
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 624d84e6c936..9d01da3b90bd 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -7,7 +7,7 @@ config PINCTRL_SUNXI
select GPIOLIB
config PINCTRL_SUN4I_A10
- def_bool MACH_SUN4I || MACH_SUN7I
+ def_bool MACH_SUN4I || MACH_SUN7I || MACH_SUN8I
select PINCTRL_SUNXI
config PINCTRL_SUN5I
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
index 159580c04b14..0f6ca8391ea7 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
@@ -26,7 +26,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "spi1"), /* CS0 */
SUNXI_FUNCTION(0x4, "uart2"), /* RTS */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD3 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -34,7 +35,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "spi1"), /* CLK */
SUNXI_FUNCTION(0x4, "uart2"), /* CTS */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD2 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -42,7 +44,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "spi1"), /* MOSI */
SUNXI_FUNCTION(0x4, "uart2"), /* TX */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD1 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -50,65 +53,75 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "spi1"), /* MISO */
SUNXI_FUNCTION(0x4, "uart2"), /* RX */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXD0 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD3 */
SUNXI_FUNCTION(0x3, "spi1"), /* CS1 */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD3 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD2 */
SUNXI_FUNCTION(0x3, "spi3"), /* CS0 */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD2 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD1 */
SUNXI_FUNCTION(0x3, "spi3"), /* CLK */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD1 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ETXD0 */
SUNXI_FUNCTION(0x3, "spi3"), /* MOSI */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXD0 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXCK */
SUNXI_FUNCTION(0x3, "spi3"), /* MISO */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXCK */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXERR */
SUNXI_FUNCTION(0x3, "spi3"), /* CS1 */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ERXERR */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* MCLK */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* ERXDV */
SUNXI_FUNCTION(0x4, "uart1"), /* TX */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GRXDV */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "emac"), /* EMDC */
SUNXI_FUNCTION(0x4, "uart1"), /* RX */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* EMDC */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -116,7 +129,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "uart6"), /* TX */
SUNXI_FUNCTION(0x4, "uart1"), /* RTS */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* EMDIO */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -124,7 +138,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "uart6"), /* RX */
SUNXI_FUNCTION(0x4, "uart1"), /* CTS */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXCTL / ETXEN */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -132,9 +147,11 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "uart7"), /* TX */
SUNXI_FUNCTION(0x4, "uart1"), /* DTR */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXCK */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* BCLK */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -142,9 +159,11 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "uart7"), /* RX */
SUNXI_FUNCTION(0x4, "uart1"), /* DSR */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GTXCK / ECRS */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* LRCK */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -152,9 +171,11 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "can"), /* TX */
SUNXI_FUNCTION(0x4, "uart1"), /* DCD */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GCLKIN / ECOL */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DO */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -162,14 +183,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x3, "can"), /* RX */
SUNXI_FUNCTION(0x4, "uart1"), /* RING */
SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXERR */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DI */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
/* Hole */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "i2c0")), /* SCK */
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_VARIANT(0x3,
+ "pll-lock-dbg",
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -177,11 +203,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "pwm")), /* PWM0 */
+ SUNXI_FUNCTION_VARIANT(0x2, "pwm", /* PWM0 */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x3, "pwm", /* PWM0 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "ir0"), /* TX */
+ SUNXI_FUNCTION_VARIANT(0x2, "ir0", /* TX */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x3, "pwm0", /* PWM1 */
+ PINCTRL_SUN8I_R40),
/*
* The SPDIF block is not referenced at all in the A10 user
* manual. However it is described in the code leaked and the
@@ -205,7 +239,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* MCLK */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* MCLK */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -213,7 +248,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* BCLK */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* BCLK */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x3, "ac97")), /* BCLK */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -221,7 +257,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* LRCK */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* LRCK */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x3, "ac97")), /* SYNC */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -229,7 +266,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO0 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO0 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x3, "ac97")), /* DO */
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -237,31 +275,41 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO1 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO1 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
+ SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM6 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO2 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO2 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
+ SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM7 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO3 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO3 */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DI */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DI */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x3, "ac97"), /* DI */
/* Undocumented mux function on A10 - See SPDIF MCLK above */
- SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF IN */
+ SUNXI_FUNCTION_VARIANT(0x4, "spdif", /* SPDIF IN */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -308,7 +356,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "uart0"), /* TX */
- SUNXI_FUNCTION(0x3, "ir1")), /* TX */
+ SUNXI_FUNCTION_VARIANT(0x3, "ir1", /* TX */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 23),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -341,7 +391,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NRE# */
+ SUNXI_FUNCTION(0x2, "nand0"), /* NRE# */
+ SUNXI_FUNCTION_VARIANT(0x3, "mmc2", /* DS */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -375,19 +427,27 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ4 */
+ SUNXI_FUNCTION(0x2, "nand0"), /* NDQ4 */
+ SUNXI_FUNCTION_VARIANT(0x3, "mmc2", /* D4 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ5 */
+ SUNXI_FUNCTION(0x2, "nand0"), /* NDQ5 */
+ SUNXI_FUNCTION_VARIANT(0x3, "mmc2", /* D5 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ6 */
+ SUNXI_FUNCTION(0x2, "nand0"), /* NDQ6 */
+ SUNXI_FUNCTION_VARIANT(0x3, "mmc2", /* D6 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQ7 */
+ SUNXI_FUNCTION(0x2, "nand0"), /* NDQ7 */
+ SUNXI_FUNCTION_VARIANT(0x3, "mmc2", /* D7 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -427,7 +487,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 24),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
- SUNXI_FUNCTION(0x2, "nand0")), /* NDQS */
+ SUNXI_FUNCTION(0x2, "nand0"), /* NDQS */
+ SUNXI_FUNCTION_VARIANT(0x3, "mmc2", /* RST */
+ PINCTRL_SUN8I_R40)),
/* Hole */
SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -728,14 +790,18 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x2, "ts1"), /* D5 */
SUNXI_FUNCTION(0x3, "csi1"), /* D5 */
SUNXI_FUNCTION(0x4, "uart3"), /* CTS */
- SUNXI_FUNCTION(0x5, "csi0")), /* D13 */
+ SUNXI_FUNCTION(0x5, "csi0"), /* D13 */
+ SUNXI_FUNCTION_VARIANT(0x6, "bist", /* RESULT0 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "ts1"), /* D6 */
SUNXI_FUNCTION(0x3, "csi1"), /* D6 */
SUNXI_FUNCTION(0x4, "uart4"), /* TX */
- SUNXI_FUNCTION(0x5, "csi0")), /* D14 */
+ SUNXI_FUNCTION(0x5, "csi0"), /* D14 */
+ SUNXI_FUNCTION_VARIANT(0x6, "bist", /* RESULT1 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -805,7 +871,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD2 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart5"), /* TX */
- SUNXI_FUNCTION(0x5, "ms"), /* BS */
+ SUNXI_FUNCTION_VARIANT(0x5, "ms", /* BS */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 6), /* EINT6 */
SUNXI_FUNCTION(0x7, "csi1")), /* D6 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
@@ -815,7 +883,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD3 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION(0x4, "uart5"), /* RX */
- SUNXI_FUNCTION(0x5, "ms"), /* CLK */
+ SUNXI_FUNCTION_VARIANT(0x5, "ms", /* CLK */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 7), /* EINT7 */
SUNXI_FUNCTION(0x7, "csi1")), /* D7 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
@@ -825,9 +895,12 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD4 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD3 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN0 */
- SUNXI_FUNCTION(0x5, "ms"), /* D0 */
+ SUNXI_FUNCTION_VARIANT(0x5, "ms", /* D0 */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 8), /* EINT8 */
SUNXI_FUNCTION(0x7, "csi1")), /* D8 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
@@ -837,9 +910,12 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD5 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD2 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN1 */
- SUNXI_FUNCTION(0x5, "ms"), /* D1 */
+ SUNXI_FUNCTION_VARIANT(0x5, "ms", /* D1 */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 9), /* EINT9 */
SUNXI_FUNCTION(0x7, "csi1")), /* D9 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
@@ -849,9 +925,12 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD6 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD1 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN2 */
- SUNXI_FUNCTION(0x5, "ms"), /* D2 */
+ SUNXI_FUNCTION_VARIANT(0x5, "ms", /* D2 */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 10), /* EINT10 */
SUNXI_FUNCTION(0x7, "csi1")), /* D10 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
@@ -861,9 +940,12 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD7 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXD0 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN3 */
- SUNXI_FUNCTION(0x5, "ms"), /* D3 */
+ SUNXI_FUNCTION_VARIANT(0x5, "ms", /* D3 */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
SUNXI_FUNCTION_IRQ(0x6, 11), /* EINT11 */
SUNXI_FUNCTION(0x7, "csi1")), /* D11 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 12),
@@ -892,7 +974,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD10 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD3 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN4 */
SUNXI_FUNCTION(0x5, "sim"), /* VPPEN */
SUNXI_FUNCTION_IRQ(0x6, 14), /* EINT14 */
@@ -904,7 +987,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD11 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD2 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN5 */
SUNXI_FUNCTION(0x5, "sim"), /* VPPPP */
SUNXI_FUNCTION_IRQ(0x6, 15), /* EINT15 */
@@ -916,7 +1000,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD12 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD1 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
+ SUNXI_FUNCTION_VARIANT(0x5, "sim", /* DET */
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
@@ -927,7 +1014,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD13 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD0 */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* IN7 */
SUNXI_FUNCTION(0x5, "sim"), /* VCCEN */
SUNXI_FUNCTION_IRQ(0x6, 17), /* EINT17 */
@@ -939,7 +1027,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD14 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXCK */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT0 */
SUNXI_FUNCTION(0x5, "sim"), /* SCK */
SUNXI_FUNCTION_IRQ(0x6, 18), /* EINT18 */
@@ -951,7 +1040,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD15 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXERR */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT1 */
SUNXI_FUNCTION(0x5, "sim"), /* SDA */
SUNXI_FUNCTION_IRQ(0x6, 19), /* EINT19 */
@@ -963,7 +1053,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAOE */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ERXDV */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "can"), /* TX */
SUNXI_FUNCTION_IRQ(0x6, 20), /* EINT20 */
SUNXI_FUNCTION(0x7, "csi1")), /* D20 */
@@ -974,7 +1065,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATADREQ */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* EMDC */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "can"), /* RX */
SUNXI_FUNCTION_IRQ(0x6, 21), /* EINT21 */
SUNXI_FUNCTION(0x7, "csi1")), /* D21 */
@@ -985,7 +1077,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATADACK */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* EMDIO */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT2 */
SUNXI_FUNCTION(0x5, "mmc1"), /* CMD */
SUNXI_FUNCTION(0x7, "csi1")), /* D22 */
@@ -996,7 +1089,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATACS0 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXEN */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT3 */
SUNXI_FUNCTION(0x5, "mmc1"), /* CLK */
SUNXI_FUNCTION(0x7, "csi1")), /* D23 */
@@ -1007,7 +1101,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATACS1 */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXCK */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT4 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D0 */
SUNXI_FUNCTION(0x7, "csi1")), /* PCLK */
@@ -1018,7 +1113,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIORDY */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ECRS */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT5 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D1 */
SUNXI_FUNCTION(0x7, "csi1")), /* FIELD */
@@ -1029,7 +1125,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIOR */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ECOL */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT6 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D2 */
SUNXI_FUNCTION(0x7, "csi1")), /* HSYNC */
@@ -1040,7 +1137,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAIOW */
PINCTRL_SUN4I_A10),
SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXERR */
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION(0x4, "keypad"), /* OUT7 */
SUNXI_FUNCTION(0x5, "mmc1"), /* D3 */
SUNXI_FUNCTION(0x7, "csi1")), /* VSYNC */
@@ -1049,23 +1147,27 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION_VARIANT(0x3, "i2c3", /* SCK */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 1),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION_VARIANT(0x3, "i2c3", /* SDA */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 2),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION_VARIANT(0x3, "i2c4", /* SCK */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "pwm"), /* PWM1 */
SUNXI_FUNCTION_VARIANT(0x3, "i2c3", /* SDA */
- PINCTRL_SUN7I_A20)),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 4),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
@@ -1108,7 +1210,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x2, "spi0"), /* MOSI */
SUNXI_FUNCTION(0x3, "uart6"), /* TX */
SUNXI_FUNCTION_VARIANT(0x4, "clk_out_a",
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_IRQ(0x6, 24)), /* EINT24 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 13),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -1116,7 +1219,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x2, "spi0"), /* MISO */
SUNXI_FUNCTION(0x3, "uart6"), /* RX */
SUNXI_FUNCTION_VARIANT(0x4, "clk_out_b",
- PINCTRL_SUN7I_A20),
+ PINCTRL_SUN7I_A20 |
+ PINCTRL_SUN8I_R40),
SUNXI_FUNCTION_IRQ(0x6, 25)), /* EINT25 */
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 14),
SUNXI_FUNCTION(0x0, "gpio_in"),
@@ -1161,13 +1265,25 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "ps2"), /* SCK0 */
SUNXI_FUNCTION(0x3, "uart7"), /* TX */
- SUNXI_FUNCTION(0x4, "hdmi")), /* HSCL */
+ SUNXI_FUNCTION_VARIANT(0x4,
+ "hdmi", /* HSCL */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6,
+ "pwm", /* PWM2 */
+ PINCTRL_SUN8I_R40)),
SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 21),
SUNXI_FUNCTION(0x0, "gpio_in"),
SUNXI_FUNCTION(0x1, "gpio_out"),
SUNXI_FUNCTION(0x2, "ps2"), /* SDA0 */
SUNXI_FUNCTION(0x3, "uart7"), /* RX */
- SUNXI_FUNCTION(0x4, "hdmi")), /* HSDA */
+ SUNXI_FUNCTION_VARIANT(0x4,
+ "hdmi", /* HSDA */
+ PINCTRL_SUN4I_A10 |
+ PINCTRL_SUN7I_A20),
+ SUNXI_FUNCTION_VARIANT(0x6,
+ "pwm", /* PWM3 */
+ PINCTRL_SUN8I_R40)),
};
static const struct sunxi_pinctrl_desc sun4i_a10_pinctrl_data = {
@@ -1194,6 +1310,10 @@ static const struct of_device_id sun4i_a10_pinctrl_match[] = {
.compatible = "allwinner,sun7i-a20-pinctrl",
.data = (void *)PINCTRL_SUN7I_A20
},
+ {
+ .compatible = "allwinner,sun8i-r40-pinctrl",
+ .data = (void *)PINCTRL_SUN8I_R40
+ },
{}
};
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (5 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-28 15:09 ` Chen-Yu Tsai
2017-05-27 10:23 ` [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC Icenowy Zheng
` (2 subsequent siblings)
9 siblings, 1 reply; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
Allwinner R40 has a clock controlling unit like the ones on other
Allwinner SoCs after sun6i, and can also use a CCU-based driver.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
---
Changes in v3:
- Rebased on current linux-next.
- Added Rob's ACK.
Documentation/devicetree/bindings/clock/sunxi-ccu.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index 34b2a9249a94..80926c5db86b 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -9,6 +9,7 @@ Required properties :
- "allwinner,sun8i-a83t-ccu"
- "allwinner,sun8i-h3-ccu"
- "allwinner,sun8i-h3-r-ccu"
+ - "allwinner,sun8i-r40-ccu"
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (6 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-29 7:34 ` Chen-Yu Tsai
2017-05-27 10:23 ` [PATCH v3 09/10] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40 Icenowy Zheng
2017-05-27 10:23 ` [PATCH v3 10/10] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra Icenowy Zheng
9 siblings, 1 reply; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
Allwinner R40 SoC have a clock controller module in the style of the
SoCs beyond sun6i, however, it's more rich and complex.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Rebased on current linux-next.
Changes in v2:
- Fixes according to the SoC's user manual.
drivers/clk/sunxi-ng/Kconfig | 10 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun8i-r40.c | 1153 +++++++++++++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun8i-r40.h | 68 ++
include/dt-bindings/clock/sun8i-r40-ccu.h | 191 +++++
include/dt-bindings/reset/sun8i-r40-ccu.h | 129 ++++
6 files changed, 1552 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.h
create mode 100644 include/dt-bindings/clock/sun8i-r40-ccu.h
create mode 100644 include/dt-bindings/reset/sun8i-r40-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 67acef3d2494..c11ad3375907 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -157,6 +157,16 @@ config SUN8I_DE2_CCU
select SUNXI_CCU_DIV
select SUNXI_CCU_GATE
+config SUN8I_R40_CCU
+ bool "Support for the Allwinner R40 CCU"
+ select SUNXI_CCU_DIV
+ select SUNXI_CCU_NK
+ select SUNXI_CCU_NKM
+ select SUNXI_CCU_NKMP
+ select SUNXI_CCU_NM
+ select SUNXI_CCU_MP
+ default MACH_SUN8I
+
config SUN9I_A80_CCU
bool "Support for the Allwinner A80 CCU"
select SUNXI_CCU_DIV
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 0185c6ffadcb..217db667a994 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
obj-$(CONFIG_SUN8I_DE2_CCU) += ccu-sun8i-de2.o
obj-$(CONFIG_SUN8I_R_CCU) += ccu-sun8i-r.o
+obj-$(CONFIG_SUN8I_R40_CCU) += ccu-sun8i-r40.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-de.o
obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-usb.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.c b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
new file mode 100644
index 000000000000..484a8956f59c
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
@@ -0,0 +1,1153 @@
+/*
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+#include "ccu_phase.h"
+
+#include "ccu-sun8i-r40.h"
+
+static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpu_clk, "pll-cpu",
+ "osc24M", 0x000,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ 16, 2, /* P */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+/*
+ * The Audio PLL is supposed to have 4 outputs: 3 fixed factors from
+ * the base (2x, 4x and 8x), and one variable divider (the one true
+ * pll audio).
+ *
+ * We don't have any need for the variable divider for now, so we just
+ * hardcode it to match with the clock names
+ */
+#define SUN8I_R40_PLL_AUDIO_REG 0x008
+
+static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
+ "osc24M", 0x008,
+ 8, 7, /* N */
+ 0, 5, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video0_clk, "pll-video0",
+ "osc24M", 0x0010,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_ve_clk, "pll-ve",
+ "osc24M", 0x0018,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_ddr0_clk, "pll-ddr0",
+ "osc24M", 0x020,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+/* According to the BSP driver, pll-periph{0,1} have M at 0:1 */
+static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_periph0_clk, "pll-periph0",
+ "osc24M", 0x028,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_periph1_clk, "pll-periph1",
+ "osc24M", 0x02c,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video1_clk, "pll-video1",
+ "osc24M", 0x030,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ CLK_SET_RATE_UNGATE);
+
+/*
+ * For the special bit in gate part, please see the BSP source code at
+ * https://github.com/BPI-SINOVOIP/BPI-M2U-bsp/blob/master/linux-sunxi/drivers/clk/sunxi/clk-sun8iw11.c#L665
+ */
+static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_sata_clk, "pll-sata",
+ "osc24M", 0x034,
+ 8, 5, /* N */
+ 4, 2, /* K */
+ 0, 2, /* M */
+ BIT(31) | BIT(14), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_gpu_clk, "pll-gpu",
+ "osc24M", 0x038,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static const char * const pll_mipi_parents[] = { "pll-video0", "pll-video1" };
+static SUNXI_CCU_NKM_WITH_MUX_GATE_LOCK(pll_mipi_clk, "pll-mipi",
+ pll_mipi_parents, 0x040,
+ 8, 4, /* N */
+ 4, 2, /* K */
+ 0, 4, /* M */
+ 21, 0, /* mux */
+ BIT(31) | BIT(23) | BIT(22), /* gate */
+ BIT(28), /* lock */
+ CLK_SET_RATE_UNGATE);
+
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
+ "osc24M", 0x0048,
+ 8, 7, /* N */
+ 0, 4, /* M */
+ BIT(24), /* frac enable */
+ BIT(25), /* frac select */
+ 270000000, /* frac rate 0 */
+ 297000000, /* frac rate 1 */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ 0);
+
+static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
+ "osc24M", 0x04c,
+ 8, 7, /* N */
+ 0, 2, /* M */
+ BIT(31), /* gate */
+ BIT(28), /* lock */
+ CLK_SET_RATE_UNGATE);
+
+static const char * const cpu_parents[] = { "osc32k", "osc24M",
+ "pll-cpu", "pll-cpu" };
+static SUNXI_CCU_MUX(cpu_clk, "cpu", cpu_parents,
+ 0x050, 16, 2, CLK_IS_CRITICAL);
+
+static SUNXI_CCU_M(axi_clk, "axi", "cpu", 0x050, 0, 2, 0);
+
+static const char * const ahb1_parents[] = { "osc32k", "osc24M",
+ "axi", "pll-periph0" };
+static const struct ccu_mux_var_prediv ahb1_predivs[] = {
+ { .index = 3, .shift = 6, .width = 2 },
+};
+static struct ccu_div ahb1_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .mux = {
+ .shift = 12,
+ .width = 2,
+
+ .var_predivs = ahb1_predivs,
+ .n_var_predivs = ARRAY_SIZE(ahb1_predivs),
+ },
+
+ .common = {
+ .reg = 0x054,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("ahb1",
+ ahb1_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct clk_div_table apb1_div_table[] = {
+ { .val = 0, .div = 2 },
+ { .val = 1, .div = 2 },
+ { .val = 2, .div = 4 },
+ { .val = 3, .div = 8 },
+ { /* Sentinel */ },
+};
+static SUNXI_CCU_DIV_TABLE(apb1_clk, "apb1", "ahb1",
+ 0x054, 8, 2, apb1_div_table, 0);
+
+static const char * const apb2_parents[] = { "osc32k", "osc24M",
+ "pll-periph0-2x",
+ "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", apb2_parents, 0x058,
+ 0, 5, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb1",
+ 0x060, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "ahb1",
+ 0x060, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "ahb1",
+ 0x060, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb1",
+ 0x060, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb1",
+ 0x060, BIT(9), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb1",
+ 0x060, BIT(10), 0);
+static SUNXI_CCU_GATE(bus_mmc3_clk, "bus-mmc3", "ahb1",
+ 0x060, BIT(11), 0);
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb1",
+ 0x060, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "ahb1",
+ 0x060, BIT(14), 0);
+static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb1",
+ 0x060, BIT(17), 0);
+static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb1",
+ 0x060, BIT(18), 0);
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "ahb1",
+ 0x060, BIT(19), 0);
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb1",
+ 0x060, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb1",
+ 0x060, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb1",
+ 0x060, BIT(22), 0);
+static SUNXI_CCU_GATE(bus_spi3_clk, "bus-spi3", "ahb1",
+ 0x060, BIT(23), 0);
+static SUNXI_CCU_GATE(bus_sata_clk, "bus-sata", "ahb1",
+ 0x060, BIT(24), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb1",
+ 0x060, BIT(25), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb1",
+ 0x060, BIT(26), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb1",
+ 0x060, BIT(27), 0);
+static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb1",
+ 0x060, BIT(28), 0);
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb1",
+ 0x060, BIT(29), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb1",
+ 0x060, BIT(30), 0);
+static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb1",
+ 0x060, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "ahb1",
+ 0x064, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_de_mp_clk, "bus-de-mp", "ahb1",
+ 0x064, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "ahb1",
+ 0x064, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_csi0_clk, "bus-csi0", "ahb1",
+ 0x064, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_csi1_clk, "bus-csi1", "ahb1",
+ 0x064, BIT(9), 0);
+static SUNXI_CCU_GATE(bus_hdmi_slow_clk, "bus-hdmi-slow", "ahb1",
+ 0x064, BIT(10), 0);
+static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb1",
+ 0x064, BIT(11), 0);
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "ahb1",
+ 0x064, BIT(12), 0);
+static SUNXI_CCU_GATE(bus_tve0_clk, "bus-tve0", "ahb1",
+ 0x064, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_tve1_clk, "bus-tve1", "ahb1",
+ 0x064, BIT(14), 0);
+static SUNXI_CCU_GATE(bus_tve_top_clk, "bus-tve-top", "ahb1",
+ 0x064, BIT(15), 0);
+static SUNXI_CCU_GATE(bus_gmac_clk, "bus-gmac", "ahb1",
+ 0x064, BIT(17), 0);
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "ahb1",
+ 0x064, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_tvd0_clk, "bus-tvd0", "ahb1",
+ 0x064, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_tvd1_clk, "bus-tvd1", "ahb1",
+ 0x064, BIT(22), 0);
+static SUNXI_CCU_GATE(bus_tvd2_clk, "bus-tvd2", "ahb1",
+ 0x064, BIT(23), 0);
+static SUNXI_CCU_GATE(bus_tvd3_clk, "bus-tvd3", "ahb1",
+ 0x064, BIT(24), 0);
+static SUNXI_CCU_GATE(bus_tvd_top_clk, "bus-tvd-top", "ahb1",
+ 0x064, BIT(25), 0);
+static SUNXI_CCU_GATE(bus_tcon0_clk, "bus-tcon0", "ahb1",
+ 0x064, BIT(26), 0);
+static SUNXI_CCU_GATE(bus_tcon1_clk, "bus-tcon1", "ahb1",
+ 0x064, BIT(27), 0);
+static SUNXI_CCU_GATE(bus_tve0_tcon_clk, "bus-tve0-tcon", "ahb1",
+ 0x064, BIT(28), 0);
+static SUNXI_CCU_GATE(bus_tve1_tcon_clk, "bus-tve1-tcon", "ahb1",
+ 0x064, BIT(29), 0);
+static SUNXI_CCU_GATE(bus_tcon_top_clk, "bus-tcon-top", "ahb1",
+ 0x064, BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_codec_clk, "bus-codec", "apb1",
+ 0x068, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1",
+ 0x068, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ac97_clk, "bus-ac97", "apb1",
+ 0x068, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_pio_clk, "bus-pio", "apb1",
+ 0x068, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_ir0_clk, "bus-ir0", "apb1",
+ 0x068, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_ir1_clk, "bus-ir1", "apb1",
+ 0x068, BIT(7), 0);
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1",
+ 0x068, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_keypad_clk, "bus-keypad", "apb1",
+ 0x068, BIT(10), 0);
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1",
+ 0x068, BIT(12), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1",
+ 0x068, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1",
+ 0x068, BIT(14), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2",
+ 0x06c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2",
+ 0x06c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2",
+ 0x06c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2",
+ 0x06c, BIT(3), 0);
+/*
+ * In datasheet here's "Reserved", however the gate exists in BSP soucre
+ * code.
+ */
+static SUNXI_CCU_GATE(bus_can_clk, "bus-can", "apb2",
+ 0x06c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
+ 0x06c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_ps20_clk, "bus-ps20", "apb2",
+ 0x06c, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_ps21_clk, "bus-ps21", "apb2",
+ 0x06c, BIT(7), 0);
+static SUNXI_CCU_GATE(bus_i2c4_clk, "bus-i2c4", "apb2",
+ 0x06c, BIT(15), 0);
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2",
+ 0x06c, BIT(16), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2",
+ 0x06c, BIT(17), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
+ 0x06c, BIT(18), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
+ 0x06c, BIT(19), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2",
+ 0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2",
+ 0x06c, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_uart6_clk, "bus-uart6", "apb2",
+ 0x06c, BIT(22), 0);
+static SUNXI_CCU_GATE(bus_uart7_clk, "bus-uart7", "apb2",
+ 0x06c, BIT(23), 0);
+
+/* Educated guess: the BSP clock driver do not have this clock */
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "ahb1",
+ 0x070, BIT(7), 0);
+
+static SUNXI_CCU_M_WITH_GATE(ths_clk, "ths", "osc24M",
+ 0x074, 0, 2, BIT(31), 0);
+
+static const char * const mod0_default_parents[] = { "osc24M", "pll-periph0",
+ "pll-periph1" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand", mod0_default_parents, 0x080,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mod0_default_parents, 0x088,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mod0_default_parents, 0x08c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mod0_default_parents, 0x090,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc3_clk, "mmc3", mod0_default_parents, 0x094,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const ts_parents[] = { "osc24M", "pll-periph0", };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x098,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const ce_parents[] = { "osc24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x09c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", mod0_default_parents, 0x0a0,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_default_parents, 0x0a4,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", mod0_default_parents, 0x0a8,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi3_clk, "spi3", mod0_default_parents, 0x0ac,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const i2s_parents[] = { "pll-audio-8x", "pll-audio-4x",
+ "pll-audio-2x", "pll-audio" };
+static SUNXI_CCU_MUX_WITH_GATE(i2s0_clk, "i2s0", i2s_parents,
+ 0x0b0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_MUX_WITH_GATE(i2s1_clk, "i2s1", i2s_parents,
+ 0x0b4, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_MUX_WITH_GATE(i2s2_clk, "i2s2", i2s_parents,
+ 0x0b8, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_MUX_WITH_GATE(ac97_clk, "ac97", i2s_parents,
+ 0x0bc, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_MUX_WITH_GATE(spdif_clk, "spdif", i2s_parents,
+ 0x0c0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static const char * const keypad_parents[] = { "osc24M", "osc32k", };
+static SUNXI_CCU_MP_WITH_MUX_GATE(keypad_clk, "keypad", keypad_parents, 0x0c4,
+ 0, 5, /* M */
+ 16, 2, /* P */
+ 25, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const sata_parents[] = { "pll-sata", "sata-ext", };
+static SUNXI_CCU_MUX_WITH_GATE(sata_clk, "sata", sata_parents,
+ 0x0c8, 24, 1, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M",
+ 0x0cc, BIT(8), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M",
+ 0x0cc, BIT(9), 0);
+static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M",
+ 0x0cc, BIT(10), 0);
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc24M",
+ 0x0cc, BIT(16), 0);
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc24M",
+ 0x0cc, BIT(17), 0);
+static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc24M",
+ 0x0cc, BIT(18), 0);
+
+static const char * const usb_ohci12m_parents[] = { "osc24M-2x", "osc24M",
+ "osc32k" };
+static SUNXI_CCU_MUX(usb_ohci0_12m_clk, "usb-ohci0-12m", usb_ohci12m_parents,
+ 0x0cc, 20, 2, 0);
+static SUNXI_CCU_MUX(usb_ohci1_12m_clk, "usb-ohci1-12m", usb_ohci12m_parents,
+ 0x0cc, 22, 2, 0);
+static SUNXI_CCU_MUX(usb_ohci2_12m_clk, "usb-ohci2-12m", usb_ohci12m_parents,
+ 0x0cc, 24, 2, 0);
+
+static const char * const ir_parents[] = { "osc24M", "pll-periph0",
+ "pll-periph1", "osc32k" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir0_clk, "ir0", ir_parents, 0x0d0,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir1_clk, "ir1", ir_parents, 0x0d4,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1" };
+static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents,
+ 0x0f4, 0, 2, 20, 2, CLK_IS_CRITICAL);
+
+static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram",
+ 0x100, BIT(0), 0);
+static SUNXI_CCU_GATE(dram_csi0_clk, "dram-csi0", "dram",
+ 0x100, BIT(1), 0);
+static SUNXI_CCU_GATE(dram_csi1_clk, "dram-csi1", "dram",
+ 0x100, BIT(2), 0);
+static SUNXI_CCU_GATE(dram_ts_clk, "dram-ts", "dram",
+ 0x100, BIT(3), 0);
+static SUNXI_CCU_GATE(dram_tvd_clk, "dram-tvd", "dram",
+ 0x100, BIT(4), 0);
+static SUNXI_CCU_GATE(dram_de_mp_clk, "dram-de-mp", "dram",
+ 0x100, BIT(5), 0);
+static SUNXI_CCU_GATE(dram_deinterlace_clk, "dram-deinterlace", "dram",
+ 0x100, BIT(6), 0);
+
+static const char * const de_parents[] = { "pll-periph0-2x", "pll-de" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents,
+ 0x104, 0, 4, 24, 3, BIT(31), 0);
+static SUNXI_CCU_M_WITH_MUX_GATE(de_mp_clk, "de-mp", de_parents,
+ 0x108, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const tcon_parents[] = { "pll-video0", "pll-video1",
+ "pll-video0-2x", "pll-video1-2x",
+ "pll-mipi" };
+static SUNXI_CCU_MUX_WITH_GATE(tcon0_clk, "tcon0", tcon_parents,
+ 0x110, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
+static SUNXI_CCU_MUX_WITH_GATE(tcon1_clk, "tcon1", tcon_parents,
+ 0x114, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_MUX_GATE(tcon_tve0_clk, "tcon-tve0", tcon_parents,
+ 0x118, 0, 4, 24, 3, BIT(31), 0);
+static SUNXI_CCU_M_WITH_MUX_GATE(tcon_tve1_clk, "tcon-tve1", tcon_parents,
+ 0x11c, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const deinterlace_parents[] = { "pll-periph0",
+ "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace",
+ deinterlace_parents, 0x124, 0, 4, 24, 3,
+ BIT(31), 0);
+
+static const char * const csi_mclk_parents[] = { "osc24M", "pll-video",
+ "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk", csi_mclk_parents,
+ 0x130, 0, 5, 8, 3, BIT(15), 0);
+
+static const char * const csi_sclk_parents[] = { "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(csi_sclk_clk, "csi-sclk", csi_sclk_parents,
+ 0x134, 16, 4, 24, 3, BIT(31), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk", csi_mclk_parents,
+ 0x134, 0, 5, 8, 3, BIT(15), 0);
+
+static SUNXI_CCU_M_WITH_GATE(ve_clk, "ve", "pll-ve",
+ 0x13c, 16, 3, BIT(31), 0);
+
+static SUNXI_CCU_GATE(adda_clk, "adda", "pll-audio",
+ 0x140, BIT(31), CLK_SET_RATE_PARENT);
+static SUNXI_CCU_GATE(adda_4x_clk, "adda-4x", "pll-audio-4x",
+ 0x140, BIT(30), CLK_SET_RATE_PARENT);
+static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M",
+ 0x144, BIT(31), 0);
+
+static const char * const hdmi_parents[] = { "pll-video0", "pll-video1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents,
+ 0x150, 0, 4, 24, 2, BIT(31), 0);
+
+static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M",
+ 0x154, BIT(31), 0);
+
+static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x",
+ "pll-ddr0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x15c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const mipi_dsi_parents[] = { "pll-video0", "pll-video1",
+ "pll-periph0" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi", mipi_dsi_parents,
+ 0x168, 0, 4, 8, 2, BIT(15), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(tve0_clk, "tve0", tcon_parents,
+ 0x180, 0, 4, 24, 3, BIT(31), 0);
+static SUNXI_CCU_M_WITH_MUX_GATE(tve1_clk, "tve1", tcon_parents,
+ 0x184, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const tvd_parents[] = { "pll-video0", "pll-video1",
+ "pll-video0-2x", "pll-video1-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(tvd0_clk, "tvd0", tvd_parents,
+ 0x188, 0, 4, 24, 2, BIT(31), 0);
+static SUNXI_CCU_M_WITH_MUX_GATE(tvd1_clk, "tvd1", tvd_parents,
+ 0x18c, 0, 4, 24, 2, BIT(31), 0);
+static SUNXI_CCU_M_WITH_MUX_GATE(tvd2_clk, "tvd2", tvd_parents,
+ 0x190, 0, 4, 24, 2, BIT(31), 0);
+static SUNXI_CCU_M_WITH_MUX_GATE(tvd3_clk, "tvd3", tvd_parents,
+ 0x194, 0, 4, 24, 2, BIT(31), 0);
+
+static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
+ 0x1a0, 0, 3, BIT(31), 0);
+
+static const char * const out_parents[] = { "osc24M-32k", "osc32k", "osc24M" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(outa_clk, "outa", out_parents, 0x1f0,
+ 8, 5, /* M */
+ 20, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+static SUNXI_CCU_MP_WITH_MUX_GATE(outb_clk, "outb", out_parents, 0x1f4,
+ 8, 5, /* M */
+ 20, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static struct ccu_common *sun8i_r40_ccu_clks[] = {
+ &pll_cpu_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video0_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_video1_clk.common,
+ &pll_sata_clk.common,
+ &pll_gpu_clk.common,
+ &pll_mipi_clk.common,
+ &pll_de_clk.common,
+ &pll_ddr1_clk.common,
+ &cpu_clk.common,
+ &axi_clk.common,
+ &ahb1_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &bus_mipi_dsi_clk.common,
+ &bus_ce_clk.common,
+ &bus_dma_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_mmc3_clk.common,
+ &bus_nand_clk.common,
+ &bus_dram_clk.common,
+ &bus_emac_clk.common,
+ &bus_ts_clk.common,
+ &bus_hstimer_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &bus_spi2_clk.common,
+ &bus_spi3_clk.common,
+ &bus_sata_clk.common,
+ &bus_otg_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ve_clk.common,
+ &bus_de_mp_clk.common,
+ &bus_deinterlace_clk.common,
+ &bus_csi0_clk.common,
+ &bus_csi1_clk.common,
+ &bus_hdmi_slow_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_de_clk.common,
+ &bus_tve0_clk.common,
+ &bus_tve1_clk.common,
+ &bus_tve_top_clk.common,
+ &bus_gmac_clk.common,
+ &bus_gpu_clk.common,
+ &bus_tvd0_clk.common,
+ &bus_tvd1_clk.common,
+ &bus_tvd2_clk.common,
+ &bus_tvd3_clk.common,
+ &bus_tvd_top_clk.common,
+ &bus_tcon0_clk.common,
+ &bus_tcon1_clk.common,
+ &bus_tve0_tcon_clk.common,
+ &bus_tve1_tcon_clk.common,
+ &bus_tcon_top_clk.common,
+ &bus_codec_clk.common,
+ &bus_spdif_clk.common,
+ &bus_ac97_clk.common,
+ &bus_pio_clk.common,
+ &bus_ir0_clk.common,
+ &bus_ir1_clk.common,
+ &bus_ths_clk.common,
+ &bus_keypad_clk.common,
+ &bus_i2s0_clk.common,
+ &bus_i2s1_clk.common,
+ &bus_i2s2_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &bus_can_clk.common,
+ &bus_scr_clk.common,
+ &bus_ps20_clk.common,
+ &bus_ps21_clk.common,
+ &bus_i2c4_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_uart5_clk.common,
+ &bus_uart6_clk.common,
+ &bus_uart7_clk.common,
+ &bus_dbg_clk.common,
+ &ths_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &mmc3_clk.common,
+ &ts_clk.common,
+ &ce_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &spi2_clk.common,
+ &spi3_clk.common,
+ &i2s0_clk.common,
+ &i2s1_clk.common,
+ &i2s2_clk.common,
+ &ac97_clk.common,
+ &spdif_clk.common,
+ &keypad_clk.common,
+ &sata_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &usb_phy2_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_ohci0_12m_clk.common,
+ &usb_ohci1_12m_clk.common,
+ &usb_ohci2_12m_clk.common,
+ &ir0_clk.common,
+ &ir1_clk.common,
+ &dram_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi0_clk.common,
+ &dram_csi1_clk.common,
+ &dram_ts_clk.common,
+ &dram_tvd_clk.common,
+ &dram_de_mp_clk.common,
+ &dram_deinterlace_clk.common,
+ &de_clk.common,
+ &de_mp_clk.common,
+ &tcon0_clk.common,
+ &tcon1_clk.common,
+ &tcon_tve0_clk.common,
+ &tcon_tve1_clk.common,
+ &deinterlace_clk.common,
+ &csi1_mclk_clk.common,
+ &csi_sclk_clk.common,
+ &csi0_mclk_clk.common,
+ &ve_clk.common,
+ &adda_clk.common,
+ &adda_4x_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &hdmi_slow_clk.common,
+ &mbus_clk.common,
+ &mipi_dsi_clk.common,
+ &tve0_clk.common,
+ &tve1_clk.common,
+ &tvd0_clk.common,
+ &tvd1_clk.common,
+ &tvd2_clk.common,
+ &tvd3_clk.common,
+ &gpu_clk.common,
+ &outa_clk.common,
+ &outb_clk.common,
+};
+
+/* We hardcode the divider to 4 for now */
+static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
+ "pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_2x_clk, "pll-audio-2x",
+ "pll-audio-base", 2, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_4x_clk, "pll-audio-4x",
+ "pll-audio-base", 1, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_8x_clk, "pll-audio-8x",
+ "pll-audio-base", 1, 2, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_periph0_2x_clk, "pll-periph0-2x",
+ "pll-periph0", 1, 2, 0);
+static CLK_FIXED_FACTOR(pll_periph1_2x_clk, "pll-periph1-2x",
+ "pll-periph1", 1, 2, 0);
+static CLK_FIXED_FACTOR(pll_video0_2x_clk, "pll-video0-2x",
+ "pll-video0", 1, 2, 0);
+static CLK_FIXED_FACTOR(pll_video1_2x_clk, "pll-video1-2x",
+ "pll-video1", 1, 2, 0);
+static CLK_FIXED_FACTOR(osc24m_2x_clk, "osc24M-2x",
+ "osc24M", 1, 2, 0);
+static CLK_FIXED_FACTOR(osc24m_32k_clk, "osc24M-32k",
+ "osc24M", 750, 1, 0);
+
+static struct clk_hw_onecell_data sun8i_r40_hw_clks = {
+ .hws = {
+ [CLK_OSC24M_2X] = &osc24m_2x_clk.hw,
+ [CLK_OSC24M_32K] = &osc24m_32k_clk.hw,
+ [CLK_PLL_CPU] = &pll_cpu_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_PLL_SATA] = &pll_sata_clk.common.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_MIPI] = &pll_mipi_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_PLL_DDR1] = &pll_ddr1_clk.common.hw,
+ [CLK_CPU] = &cpu_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB1] = &ahb1_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_MMC3] = &bus_mmc3_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
+ [CLK_BUS_SPI3] = &bus_spi3_clk.common.hw,
+ [CLK_BUS_SATA] = &bus_sata_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DE_MP] = &bus_de_mp_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_BUS_CSI0] = &bus_csi0_clk.common.hw,
+ [CLK_BUS_CSI1] = &bus_csi1_clk.common.hw,
+ [CLK_BUS_HDMI_SLOW] = &bus_hdmi_slow_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_BUS_TVE0] = &bus_tve0_clk.common.hw,
+ [CLK_BUS_TVE1] = &bus_tve1_clk.common.hw,
+ [CLK_BUS_TVE_TOP] = &bus_tve_top_clk.common.hw,
+ [CLK_BUS_GMAC] = &bus_gmac_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_BUS_TVD0] = &bus_tvd0_clk.common.hw,
+ [CLK_BUS_TVD1] = &bus_tvd1_clk.common.hw,
+ [CLK_BUS_TVD2] = &bus_tvd2_clk.common.hw,
+ [CLK_BUS_TVD3] = &bus_tvd3_clk.common.hw,
+ [CLK_BUS_TVD_TOP] = &bus_tvd_top_clk.common.hw,
+ [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
+ [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
+ [CLK_BUS_TVE0_TCON] = &bus_tve0_tcon_clk.common.hw,
+ [CLK_BUS_TVE1_TCON] = &bus_tve1_tcon_clk.common.hw,
+ [CLK_BUS_TCON_TOP] = &bus_tcon_top_clk.common.hw,
+ [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_BUS_AC97] = &bus_ac97_clk.common.hw,
+ [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
+ [CLK_BUS_IR0] = &bus_ir0_clk.common.hw,
+ [CLK_BUS_IR1] = &bus_ir1_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_BUS_KEYPAD] = &bus_keypad_clk.common.hw,
+ [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
+ [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
+ [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_BUS_CAN] = &bus_can_clk.common.hw,
+ [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
+ [CLK_BUS_PS20] = &bus_ps20_clk.common.hw,
+ [CLK_BUS_PS21] = &bus_ps21_clk.common.hw,
+ [CLK_BUS_I2C4] = &bus_i2c4_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_UART5] = &bus_uart5_clk.common.hw,
+ [CLK_BUS_UART6] = &bus_uart6_clk.common.hw,
+ [CLK_BUS_UART7] = &bus_uart7_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_THS] = &ths_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_MMC3] = &mmc3_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_SPI3] = &spi3_clk.common.hw,
+ [CLK_I2S0] = &i2s0_clk.common.hw,
+ [CLK_I2S1] = &i2s1_clk.common.hw,
+ [CLK_I2S2] = &i2s2_clk.common.hw,
+ [CLK_AC97] = &ac97_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_KEYPAD] = &keypad_clk.common.hw,
+ [CLK_SATA] = &sata_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_OHCI0_12M] = &usb_ohci0_12m_clk.common.hw,
+ [CLK_USB_OHCI1_12M] = &usb_ohci1_12m_clk.common.hw,
+ [CLK_USB_OHCI2_12M] = &usb_ohci2_12m_clk.common.hw,
+ [CLK_IR0] = &ir0_clk.common.hw,
+ [CLK_IR1] = &ir1_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI0] = &dram_csi0_clk.common.hw,
+ [CLK_DRAM_CSI1] = &dram_csi1_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DRAM_TVD] = &dram_tvd_clk.common.hw,
+ [CLK_DRAM_DE_MP] = &dram_de_mp_clk.common.hw,
+ [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_DE_MP] = &de_mp_clk.common.hw,
+ [CLK_TCON0] = &tcon0_clk.common.hw,
+ [CLK_TCON1] = &tcon1_clk.common.hw,
+ [CLK_TCON_TVE0] = &tcon_tve0_clk.common.hw,
+ [CLK_TCON_TVE1] = &tcon_tve1_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
+ [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
+ [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_ADDA] = &adda_clk.common.hw,
+ [CLK_ADDA_4X] = &adda_4x_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_SLOW] = &hdmi_slow_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
+ [CLK_TVE0] = &tve0_clk.common.hw,
+ [CLK_TVE1] = &tve1_clk.common.hw,
+ [CLK_TVD0] = &tvd0_clk.common.hw,
+ [CLK_TVD1] = &tvd1_clk.common.hw,
+ [CLK_TVD2] = &tvd2_clk.common.hw,
+ [CLK_TVD3] = &tvd3_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_OUTA] = &outa_clk.common.hw,
+ [CLK_OUTB] = &outb_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun8i_r40_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+ [RST_USB_PHY2] = { 0x0cc, BIT(2) },
+
+ [RST_MBUS] = { 0x0fc, BIT(31) },
+
+ [RST_BUS_MIPI_DSI] = { 0x2c0, BIT(1) },
+ [RST_BUS_CE] = { 0x2c0, BIT(5) },
+ [RST_BUS_DMA] = { 0x2c0, BIT(6) },
+ [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
+ [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
+ [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
+ [RST_BUS_MMC3] = { 0x2c0, BIT(11) },
+ [RST_BUS_NAND] = { 0x2c0, BIT(13) },
+ [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
+ [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
+ [RST_BUS_TS] = { 0x2c0, BIT(18) },
+ [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
+ [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
+ [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
+ [RST_BUS_SPI2] = { 0x2c0, BIT(22) },
+ [RST_BUS_SPI3] = { 0x2c0, BIT(23) },
+ [RST_BUS_SATA] = { 0x2c0, BIT(24) },
+ [RST_BUS_OTG] = { 0x2c0, BIT(25) },
+ [RST_BUS_EHCI0] = { 0x2c0, BIT(26) },
+ [RST_BUS_EHCI1] = { 0x2c0, BIT(27) },
+ [RST_BUS_EHCI2] = { 0x2c0, BIT(28) },
+ [RST_BUS_OHCI0] = { 0x2c0, BIT(29) },
+ [RST_BUS_OHCI1] = { 0x2c0, BIT(30) },
+ [RST_BUS_OHCI2] = { 0x2c0, BIT(31) },
+
+ [RST_BUS_VE] = { 0x2c4, BIT(0) },
+ [RST_BUS_DE_MP] = { 0x2c4, BIT(2) },
+ [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
+ [RST_BUS_CSI0] = { 0x2c4, BIT(8) },
+ [RST_BUS_CSI1] = { 0x2c4, BIT(9) },
+ [RST_BUS_HDMI_SLOW] = { 0x2c4, BIT(10) },
+ [RST_BUS_HDMI] = { 0x2c4, BIT(11) },
+ [RST_BUS_DE] = { 0x2c4, BIT(12) },
+ [RST_BUS_TVE0] = { 0x2c4, BIT(13) },
+ [RST_BUS_TVE1] = { 0x2c4, BIT(14) },
+ [RST_BUS_TVE_TOP] = { 0x2c4, BIT(15) },
+ [RST_BUS_GMAC] = { 0x2c4, BIT(17) },
+ [RST_BUS_GPU] = { 0x2c4, BIT(20) },
+ [RST_BUS_TVD0] = { 0x2c4, BIT(21) },
+ [RST_BUS_TVD1] = { 0x2c4, BIT(22) },
+ [RST_BUS_TVD2] = { 0x2c4, BIT(23) },
+ [RST_BUS_TVD3] = { 0x2c4, BIT(24) },
+ [RST_BUS_TVD_TOP] = { 0x2c4, BIT(25) },
+ [RST_BUS_TCON0] = { 0x2c4, BIT(26) },
+ [RST_BUS_TCON1] = { 0x2c4, BIT(27) },
+ [RST_BUS_TCON_TVE0] = { 0x2c4, BIT(28) },
+ [RST_BUS_TCON_TVE1] = { 0x2c4, BIT(29) },
+ [RST_BUS_TCON_TOP] = { 0x2c4, BIT(30) },
+ [RST_BUS_DBG] = { 0x2c4, BIT(31) },
+
+ [RST_BUS_LVDS] = { 0x2c8, BIT(0) },
+
+ [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
+ [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
+ [RST_BUS_AC97] = { 0x2d0, BIT(2) },
+ [RST_BUS_IR0] = { 0x2d0, BIT(6) },
+ [RST_BUS_IR1] = { 0x2d0, BIT(7) },
+ [RST_BUS_THS] = { 0x2d0, BIT(8) },
+ [RST_BUS_KEYPAD] = { 0x2d0, BIT(10) },
+ [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
+ [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
+ [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
+
+ [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
+ [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
+ [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
+ [RST_BUS_I2C3] = { 0x2d8, BIT(3) },
+ [RST_BUS_CAN] = { 0x2d8, BIT(4) },
+ [RST_BUS_SCR] = { 0x2d8, BIT(5) },
+ [RST_BUS_PS20] = { 0x2d8, BIT(6) },
+ [RST_BUS_PS21] = { 0x2d8, BIT(7) },
+ [RST_BUS_I2C4] = { 0x2d8, BIT(15) },
+ [RST_BUS_UART0] = { 0x2d8, BIT(16) },
+ [RST_BUS_UART1] = { 0x2d8, BIT(17) },
+ [RST_BUS_UART2] = { 0x2d8, BIT(18) },
+ [RST_BUS_UART3] = { 0x2d8, BIT(19) },
+ [RST_BUS_UART4] = { 0x2d8, BIT(20) },
+ [RST_BUS_UART5] = { 0x2d8, BIT(21) },
+ [RST_BUS_UART6] = { 0x2d8, BIT(22) },
+ [RST_BUS_UART7] = { 0x2d8, BIT(23) },
+};
+
+static const struct sunxi_ccu_desc sun8i_r40_ccu_desc = {
+ .ccu_clks = sun8i_r40_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun8i_r40_ccu_clks),
+
+ .hw_clks = &sun8i_r40_hw_clks,
+
+ .resets = sun8i_r40_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun8i_r40_ccu_resets),
+};
+
+static struct ccu_mux_nb sun8i_r40_cpu_nb = {
+ .common = &cpu_clk.common,
+ .cm = &cpu_clk.mux,
+ .delay_us = 1, /* > 8 clock cycles at 24 MHz */
+ .bypass_index = 1, /* index of 24 MHz oscillator */
+};
+
+static void __init sun8i_r40_ccu_setup(struct device_node *node)
+{
+ void __iomem *reg;
+ u32 val;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg)) {
+ pr_err("%s: Could not map the clock registers\n",
+ of_node_full_name(node));
+ return;
+ }
+
+ /* Force the PLL-Audio-1x divider to 4 */
+ val = readl(reg + SUN8I_R40_PLL_AUDIO_REG);
+ val &= ~GENMASK(19, 16);
+ writel(val | (3 << 16), reg + SUN8I_R40_PLL_AUDIO_REG);
+
+ sunxi_ccu_probe(node, reg, &sun8i_r40_ccu_desc);
+
+ ccu_mux_notifier_register(pll_cpu_clk.common.hw.clk,
+ &sun8i_r40_cpu_nb);
+}
+CLK_OF_DECLARE(sun8i_r40_ccu, "allwinner,sun8i-r40-ccu",
+ sun8i_r40_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.h b/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
new file mode 100644
index 000000000000..be30eb662d78
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
@@ -0,0 +1,68 @@
+/*
+ * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_SUN8I_R40_H_
+#define _CCU_SUN8I_R40_H_
+
+#include <dt-bindings/clock/sun8i-r40-ccu.h>
+#include <dt-bindings/reset/sun8i-r40-ccu.h>
+
+#define CLK_OSC24M_2X 0
+#define CLK_OSC24M_32K 1
+#define CLK_PLL_CPU 2
+#define CLK_PLL_AUDIO_BASE 3
+#define CLK_PLL_AUDIO 4
+#define CLK_PLL_AUDIO_2X 5
+#define CLK_PLL_AUDIO_4X 6
+#define CLK_PLL_AUDIO_8X 7
+#define CLK_PLL_VIDEO0 8
+#define CLK_PLL_VIDEO0_2X 9
+#define CLK_PLL_VE 10
+#define CLK_PLL_DDR0 11
+#define CLK_PLL_PERIPH0 12
+#define CLK_PLL_PERIPH0_2X 13
+#define CLK_PLL_PERIPH1 14
+#define CLK_PLL_PERIPH1_2X 15
+#define CLK_PLL_VIDEO1 16
+#define CLK_PLL_VIDEO1_2X 17
+#define CLK_PLL_SATA 18
+#define CLK_PLL_GPU 19
+#define CLK_PLL_MIPI 20
+#define CLK_PLL_DE 21
+#define CLK_PLL_DDR1 22
+
+/* The CPU clock is exported */
+
+#define CLK_AXI 24
+#define CLK_AHB1 25
+#define CLK_APB1 26
+#define CLK_APB2 27
+
+/* All the bus gates are exported */
+
+/* The first bunch of module clocks are exported */
+
+#define CLK_DRAM 134
+
+/* All the DRAM gates are exported */
+
+/* Some more module clocks are exported */
+
+#define CLK_MBUS 158
+
+/* Another bunch of module clocks are exported */
+
+#define CLK_NUMBER (CLK_OUTB + 1)
+
+#endif /* _CCU_SUN8I_R40_H_ */
diff --git a/include/dt-bindings/clock/sun8i-r40-ccu.h b/include/dt-bindings/clock/sun8i-r40-ccu.h
new file mode 100644
index 000000000000..a907d841496d
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-r40-ccu.h
@@ -0,0 +1,191 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN8I_R40_H_
+#define _DT_BINDINGS_CLK_SUN8I_R40_H_
+
+#define CLK_CPU 23
+
+#define CLK_BUS_MIPI_DSI 28
+#define CLK_BUS_CE 29
+#define CLK_BUS_DMA 30
+#define CLK_BUS_MMC0 31
+#define CLK_BUS_MMC1 32
+#define CLK_BUS_MMC2 33
+#define CLK_BUS_MMC3 34
+#define CLK_BUS_NAND 35
+#define CLK_BUS_DRAM 36
+#define CLK_BUS_EMAC 37
+#define CLK_BUS_TS 38
+#define CLK_BUS_HSTIMER 39
+#define CLK_BUS_SPI0 40
+#define CLK_BUS_SPI1 41
+#define CLK_BUS_SPI2 42
+#define CLK_BUS_SPI3 43
+#define CLK_BUS_SATA 44
+#define CLK_BUS_OTG 45
+#define CLK_BUS_EHCI0 46
+#define CLK_BUS_EHCI1 47
+#define CLK_BUS_EHCI2 48
+#define CLK_BUS_OHCI0 49
+#define CLK_BUS_OHCI1 50
+#define CLK_BUS_OHCI2 51
+#define CLK_BUS_VE 52
+#define CLK_BUS_DE_MP 53
+#define CLK_BUS_DEINTERLACE 54
+#define CLK_BUS_CSI0 55
+#define CLK_BUS_CSI1 56
+#define CLK_BUS_HDMI_SLOW 57
+#define CLK_BUS_HDMI 58
+#define CLK_BUS_DE 59
+#define CLK_BUS_TVE0 60
+#define CLK_BUS_TVE1 61
+#define CLK_BUS_TVE_TOP 62
+#define CLK_BUS_GMAC 63
+#define CLK_BUS_GPU 64
+#define CLK_BUS_TVD0 65
+#define CLK_BUS_TVD1 66
+#define CLK_BUS_TVD2 67
+#define CLK_BUS_TVD3 68
+#define CLK_BUS_TVD_TOP 69
+#define CLK_BUS_TCON0 70
+#define CLK_BUS_TCON1 71
+#define CLK_BUS_TVE0_TCON 72
+#define CLK_BUS_TVE1_TCON 73
+#define CLK_BUS_TCON_TOP 74
+#define CLK_BUS_CODEC 75
+#define CLK_BUS_SPDIF 76
+#define CLK_BUS_AC97 77
+#define CLK_BUS_PIO 78
+#define CLK_BUS_IR0 79
+#define CLK_BUS_IR1 80
+#define CLK_BUS_THS 81
+#define CLK_BUS_KEYPAD 82
+#define CLK_BUS_I2S0 83
+#define CLK_BUS_I2S1 84
+#define CLK_BUS_I2S2 85
+#define CLK_BUS_I2C0 86
+#define CLK_BUS_I2C1 87
+#define CLK_BUS_I2C2 88
+#define CLK_BUS_I2C3 89
+#define CLK_BUS_CAN 90
+#define CLK_BUS_SCR 91
+#define CLK_BUS_PS20 92
+#define CLK_BUS_PS21 93
+#define CLK_BUS_I2C4 94
+#define CLK_BUS_UART0 95
+#define CLK_BUS_UART1 96
+#define CLK_BUS_UART2 97
+#define CLK_BUS_UART3 98
+#define CLK_BUS_UART4 99
+#define CLK_BUS_UART5 100
+#define CLK_BUS_UART6 101
+#define CLK_BUS_UART7 102
+#define CLK_BUS_DBG 103
+
+#define CLK_THS 104
+#define CLK_NAND 105
+#define CLK_MMC0 106
+#define CLK_MMC1 107
+#define CLK_MMC2 108
+#define CLK_MMC3 109
+#define CLK_TS 110
+#define CLK_CE 111
+#define CLK_SPI0 112
+#define CLK_SPI1 113
+#define CLK_SPI2 114
+#define CLK_SPI3 115
+#define CLK_I2S0 116
+#define CLK_I2S1 117
+#define CLK_I2S2 118
+#define CLK_AC97 119
+#define CLK_SPDIF 120
+#define CLK_KEYPAD 121
+#define CLK_SATA 122
+#define CLK_USB_PHY0 123
+#define CLK_USB_PHY1 124
+#define CLK_USB_PHY2 125
+#define CLK_USB_OHCI0 126
+#define CLK_USB_OHCI1 127
+#define CLK_USB_OHCI2 128
+#define CLK_USB_OHCI0_12M 129
+#define CLK_USB_OHCI1_12M 130
+#define CLK_USB_OHCI2_12M 131
+#define CLK_IR0 132
+#define CLK_IR1 133
+
+#define CLK_DRAM_VE 135
+#define CLK_DRAM_CSI0 136
+#define CLK_DRAM_CSI1 137
+#define CLK_DRAM_TS 138
+#define CLK_DRAM_TVD 139
+#define CLK_DRAM_DE_MP 140
+#define CLK_DRAM_DEINTERLACE 141
+#define CLK_DE 142
+#define CLK_DE_MP 143
+#define CLK_TCON0 144
+#define CLK_TCON1 145
+#define CLK_TCON_TVE0 146
+#define CLK_TCON_TVE1 147
+#define CLK_DEINTERLACE 148
+#define CLK_CSI1_MCLK 149
+#define CLK_CSI_SCLK 150
+#define CLK_CSI0_MCLK 151
+#define CLK_VE 152
+#define CLK_ADDA 153
+#define CLK_ADDA_4X 154
+#define CLK_AVS 155
+#define CLK_HDMI 156
+#define CLK_HDMI_SLOW 157
+
+#define CLK_MIPI_DSI 159
+#define CLK_TVE0 160
+#define CLK_TVE1 161
+#define CLK_TVD0 162
+#define CLK_TVD1 163
+#define CLK_TVD2 164
+#define CLK_TVD3 165
+#define CLK_GPU 166
+#define CLK_OUTA 167
+#define CLK_OUTB 168
+
+#endif /* _DT_BINDINGS_CLK_SUN8I_R40_H_ */
diff --git a/include/dt-bindings/reset/sun8i-r40-ccu.h b/include/dt-bindings/reset/sun8i-r40-ccu.h
new file mode 100644
index 000000000000..a7001f34b0b9
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-r40-ccu.h
@@ -0,0 +1,129 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN8I_R40_H_
+#define _DT_BINDINGS_RST_SUN8I_R40_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_PHY2 2
+
+#define RST_MBUS 3
+
+#define RST_BUS_MIPI_DSI 4
+#define RST_BUS_CE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MMC0 7
+#define RST_BUS_MMC1 8
+#define RST_BUS_MMC2 9
+#define RST_BUS_MMC3 10
+#define RST_BUS_NAND 11
+#define RST_BUS_DRAM 12
+#define RST_BUS_EMAC 13
+#define RST_BUS_TS 14
+#define RST_BUS_HSTIMER 15
+#define RST_BUS_SPI0 16
+#define RST_BUS_SPI1 17
+#define RST_BUS_SPI2 18
+#define RST_BUS_SPI3 19
+#define RST_BUS_SATA 20
+#define RST_BUS_OTG 21
+#define RST_BUS_EHCI0 22
+#define RST_BUS_EHCI1 23
+#define RST_BUS_EHCI2 24
+#define RST_BUS_OHCI0 25
+#define RST_BUS_OHCI1 26
+#define RST_BUS_OHCI2 27
+#define RST_BUS_VE 28
+#define RST_BUS_DE_MP 29
+#define RST_BUS_DEINTERLACE 30
+#define RST_BUS_CSI0 31
+#define RST_BUS_CSI1 32
+#define RST_BUS_HDMI_SLOW 33
+#define RST_BUS_HDMI 34
+#define RST_BUS_DE 35
+#define RST_BUS_TVE0 36
+#define RST_BUS_TVE1 37
+#define RST_BUS_TVE_TOP 38
+#define RST_BUS_GMAC 39
+#define RST_BUS_GPU 40
+#define RST_BUS_TVD0 41
+#define RST_BUS_TVD1 42
+#define RST_BUS_TVD2 43
+#define RST_BUS_TVD3 44
+#define RST_BUS_TVD_TOP 45
+#define RST_BUS_TCON0 46
+#define RST_BUS_TCON1 47
+#define RST_BUS_TCON_TVE0 48
+#define RST_BUS_TCON_TVE1 49
+#define RST_BUS_TCON_TOP 50
+#define RST_BUS_DBG 51
+#define RST_BUS_LVDS 52
+#define RST_BUS_CODEC 53
+#define RST_BUS_SPDIF 54
+#define RST_BUS_AC97 55
+#define RST_BUS_IR0 56
+#define RST_BUS_IR1 57
+#define RST_BUS_THS 58
+#define RST_BUS_KEYPAD 59
+#define RST_BUS_I2S0 60
+#define RST_BUS_I2S1 61
+#define RST_BUS_I2S2 62
+#define RST_BUS_I2C0 63
+#define RST_BUS_I2C1 64
+#define RST_BUS_I2C2 65
+#define RST_BUS_I2C3 66
+#define RST_BUS_CAN 67
+#define RST_BUS_SCR 68
+#define RST_BUS_PS20 69
+#define RST_BUS_PS21 70
+#define RST_BUS_I2C4 71
+#define RST_BUS_UART0 72
+#define RST_BUS_UART1 73
+#define RST_BUS_UART2 74
+#define RST_BUS_UART3 75
+#define RST_BUS_UART4 76
+#define RST_BUS_UART5 77
+#define RST_BUS_UART6 78
+#define RST_BUS_UART7 79
+
+#endif /* _DT_BINDINGS_RST_SUN8I_R40_H_ */
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 09/10] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (7 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-29 8:15 ` Chen-Yu Tsai
2017-05-27 10:23 ` [PATCH v3 10/10] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra Icenowy Zheng
9 siblings, 1 reply; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
From: Chen-Yu Tsai <wens@csie.org>
The Allwinner R40 SoC is marketed as the successor to the A20 SoC.
The R40 is a smaller chip than the A20, but features the same set
of programmable pins, with a couple extra pins and some new pin
functions. The chip features 4 Cortex-A7 cores and a Mali-400 MP2
GPU. It retains most if not all features from the A20, while adding
some new features, such as MIPI DSI output, or updating various
hardware blocks, such as DE 2.0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Pinmux changes.
arch/arm/boot/dts/sun8i-r40.dtsi | 408 +++++++++++++++++++++++++++++++++++++++
1 file changed, 408 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r40.dtsi
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
new file mode 100644
index 000000000000..1d36485c6ef7
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -0,0 +1,408 @@
+/*
+ * Copyright 2017 Chen-Yu Tsai <wens@csie.org>
+ * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun8i-r40-ccu.h>
+#include <dt-bindings/reset/sun8i-r40-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+
+ aliases {
+ };
+
+ chosen {
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ osc32k: osc32k {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x40000000 0x80000000>;
+ };
+
+ soc@1c00000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ nmi_intc: interrupt-controller@1c00030 {
+ compatible = "allwinner,sun7i-a20-sc-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01c00030 0x0c>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ mmc0: mmc@1c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ max-frequency = <150000000>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@1c10000 {
+ compatible = "allwinner,sun50i-a64-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ max-frequency = <150000000>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@1c11000 {
+ compatible = "allwinner,sun50i-a64-emmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ pinctrl-0 = <&mmc2_pins>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ max-frequency = <200000000>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc@1c12000 {
+ compatible = "allwinner,sun50i-a64-mmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC3>, <&ccu CLK_MMC3>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC3>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ max-frequency = <150000000>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ccu: clock@1c20000 {
+ compatible = "allwinner,sun8i-r40-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl@1c20800 {
+ compatible = "allwinner,sun8i-r40-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #gpio-cells = <3>;
+
+ i2c0_pins: i2c0-pins {
+ pins = "PB0", "PB1";
+ function = "i2c0";
+ };
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pg_pins: mmc1-pg-pins {
+ pins = "PG0", "PG1", "PG2",
+ "PG3", "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_pins: mmc2-pins {
+ pins = "PC5", "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13", "PC14",
+ "PC15", "PC24";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB22", "PB23";
+ function = "uart0";
+ };
+ };
+
+ uart0: serial@1c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@1c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@1c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ uart5: serial@1c29400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29400 0x400>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ status = "disabled";
+ };
+
+ uart6: serial@1c29800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29800 0x400>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART6>;
+ resets = <&ccu RST_BUS_UART6>;
+ status = "disabled";
+ };
+
+ uart7: serial@1c29c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29c00 0x400>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART7>;
+ resets = <&ccu RST_BUS_UART7>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@1c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@1c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@1c2b800 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b800 0x400>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c4: i2c@1c2c000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2c000 0x400>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C4>;
+ resets = <&ccu RST_BUS_I2C4>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ clock-frequency = <24000000>;
+ arm,cpu-registers-not-fw-configured;
+ };
+};
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* [PATCH v3 10/10] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
` (8 preceding siblings ...)
2017-05-27 10:23 ` [PATCH v3 09/10] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40 Icenowy Zheng
@ 2017-05-27 10:23 ` Icenowy Zheng
2017-05-29 8:59 ` Chen-Yu Tsai
9 siblings, 1 reply; 36+ messages in thread
From: Icenowy Zheng @ 2017-05-27 10:23 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij
Cc: linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio, Icenowy Zheng
From: Chen-Yu Tsai <wens@csie.org>
The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 2 GB DDR3 DRAM
- 8 GB eMMC
- micro SD card slot
- DC power jack
- HDMI output
- MIPI DSI connector
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 chip, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- consumer IR receiver
- audio out headphone jack
- onboard microphone
- red, green, and blue LEDs
- debug UART pins
- Li-Po battery connector
- Raspberry Pi B+ compatible GPIO header
- power, reset, and boot control buttons
This patch adds a dts file that enables debug UART and MMC support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Pinmux changes.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 157 ++++++++++++++++++++++
2 files changed, 158 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f68d6e0bc746..697c600bba28 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -910,6 +910,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-plus.dtb \
sun8i-h3-orangepi-plus2e.dtb \
sun8i-r16-parrot.dtb \
+ sun8i-r40-bananapi-m2-ultra.dtb \
sun8i-v3s-licheepi-zero.dtb \
sun8i-v3s-licheepi-zero-dock.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
new file mode 100644
index 000000000000..c4e69847cea1
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -0,0 +1,157 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-r40.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+ model = "Banana Pi BPI-M2-Ultra";
+ compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pg_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
--
2.12.2
^ permalink raw reply related [flat|nested] 36+ messages in thread
* Re: [PATCH v3 01/10] arm: sunxi: add support for R40 SoC
2017-05-27 10:22 ` [PATCH v3 01/10] arm: sunxi: add support for R40 SoC Icenowy Zheng
@ 2017-05-28 14:57 ` Chen-Yu Tsai
2017-05-31 19:42 ` Rob Herring
1 sibling, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-28 14:57 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:22 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Allwinner R40 is a new SoC, with Quad Core Cortex-A7 and peripherals
> like A20.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Use V1.0 documents.
>
> Documentation/arm/sunxi/README | 6 ++++++
> Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
> arch/arm/mach-sunxi/sunxi.c | 1 +
> 3 files changed, 8 insertions(+)
>
> diff --git a/Documentation/arm/sunxi/README b/Documentation/arm/sunxi/README
> index d7b1f016bd62..af56321137e8 100644
> --- a/Documentation/arm/sunxi/README
> +++ b/Documentation/arm/sunxi/README
> @@ -75,6 +75,12 @@ SunXi family
> + Datasheet
> http://linux-sunxi.org/File:Allwinner_V3s_Datasheet_V1.0.pdf
>
> + - Allwinner R40 (sun8i)
> + + Datasheet
> + https://github.com/tinalinux/docs/blob/r40-v1.y/R40_Datasheet_V1.0.pdf
> + + User Manual
> + https://github.com/tinalinux/docs/blob/r40-v1.y/Allwinner_R40_User_Manual_V1.0.pdf
> +
> * Quad ARM Cortex-A15, Quad ARM Cortex-A7 based SoCs
> - Allwinner A80
> + Datasheet
> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
> index d2c46449b4eb..b3ffe6cf821a 100644
> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
> @@ -14,6 +14,7 @@ using one of the following compatible strings:
> allwinner,sun8i-a83t
> allwinner,sun8i-h2-plus
> allwinner,sun8i-h3
> + allwinner-sun8i-r40
v3s is missing from this list. Can you send a separate patch to add it?
> allwinner,sun9i-a80
> allwinner,sun50i-a64
> nextthing,gr8
> diff --git a/arch/arm/mach-sunxi/sunxi.c b/arch/arm/mach-sunxi/sunxi.c
> index f44e3acb5c90..aea616759451 100644
> --- a/arch/arm/mach-sunxi/sunxi.c
> +++ b/arch/arm/mach-sunxi/sunxi.c
> @@ -66,6 +66,7 @@ static const char * const sun8i_board_dt_compat[] = {
> "allwinner,sun8i-h2-plus",
> "allwinner,sun8i-h3",
> "allwinner,sun8i-v3s",
> + "allwinner,sun8i-r40",
Prefer to have them in alphabetical order.
Otherwise,
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> NULL,
> };
>
> --
> 2.12.2
>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs
2017-05-27 10:23 ` [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs Icenowy Zheng
@ 2017-05-28 14:58 ` Chen-Yu Tsai
2017-05-29 16:33 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-28 14:58 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Allwinner A10, A20 and R40 SoCs have similar GPIO layout.
>
> Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support
> into A10 driver, and add R40 support into it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver
2017-05-27 10:23 ` [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver Icenowy Zheng
@ 2017-05-28 15:06 ` Chen-Yu Tsai
2017-05-29 16:35 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-28 15:06 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> As A20 is designed as a pin-compatible upgrade of A10, their pin
> controller are very similar, and can share one driver.
>
> Add A20 support to the A10 driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver
2017-05-27 10:23 ` [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver Icenowy Zheng
@ 2017-05-28 15:08 ` Chen-Yu Tsai
2017-05-29 16:39 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-28 15:08 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> As we added A20 support to A10 pinctrl driver, now we can delete the
> dedicated A20 pinctrl driver, which is duplicated code.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Only remove the A20 driver(A10 driver for A20 is enabled in
> the previous commit now).
>
> drivers/pinctrl/sunxi/Kconfig | 4 -
> drivers/pinctrl/sunxi/pinctrl-sun7i-a20.c | 1056 -----------------------------
You forgot to remove the Makefile entry. Otherwise,
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl
2017-05-27 10:23 ` [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl Icenowy Zheng
@ 2017-05-28 15:09 ` Chen-Yu Tsai
2017-05-29 16:40 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-28 15:09 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Allwinner R40 has a pin controller like the ones in older Allwinner SoCs
> (especially A20), and can use modified version of the A10/A20 pinctrl
> driver.
>
> Add a compatible string for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
> ---
> Changes in v3:
> - Added Rob's ACK.
>
> Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> index b53224473672..3ab9f7849a19 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> @@ -22,6 +22,7 @@ Required properties:
> "allwinner,sun8i-a83t-pinctrl"
> "allwinner,sun8i-h3-pinctrl"
> "allwinner,sun8i-h3-r-pinctrl"
> + "allwinner,sun8i-r40-pinctrl"
Seems like we are missing an entry for the V3s. Can you send a separate patch?
Thanks
> "allwinner,sun50i-a64-pinctrl"
> "allwinner,sun50i-a64-r-pinctrl"
> "allwinner,sun50i-h5-pinctrl"
> --
> 2.12.2
>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU
2017-05-27 10:23 ` [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU Icenowy Zheng
@ 2017-05-28 15:09 ` Chen-Yu Tsai
2017-08-19 8:17 ` Chen-Yu Tsai
0 siblings, 1 reply; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-28 15:09 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Allwinner R40 has a clock controlling unit like the ones on other
> Allwinner SoCs after sun6i, and can also use a CCU-based driver.
>
> Add a compatible string for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-05-27 10:23 ` [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC Icenowy Zheng
@ 2017-05-29 7:34 ` Chen-Yu Tsai
2017-07-22 3:00 ` icenowy
2017-08-12 4:04 ` icenowy
0 siblings, 2 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-29 7:34 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Maxime Ripard, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
Hi,
On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
> Allwinner R40 SoC have a clock controller module in the style of the
> SoCs beyond sun6i, however, it's more rich and complex.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Rebased on current linux-next.
> Changes in v2:
> - Fixes according to the SoC's user manual.
>
> drivers/clk/sunxi-ng/Kconfig | 10 +
> drivers/clk/sunxi-ng/Makefile | 1 +
> drivers/clk/sunxi-ng/ccu-sun8i-r40.c | 1153 +++++++++++++++++++++++++++++
> drivers/clk/sunxi-ng/ccu-sun8i-r40.h | 68 ++
> include/dt-bindings/clock/sun8i-r40-ccu.h | 191 +++++
> include/dt-bindings/reset/sun8i-r40-ccu.h | 129 ++++
> 6 files changed, 1552 insertions(+)
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.h
> create mode 100644 include/dt-bindings/clock/sun8i-r40-ccu.h
> create mode 100644 include/dt-bindings/reset/sun8i-r40-ccu.h
>
> diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
> index 67acef3d2494..c11ad3375907 100644
> --- a/drivers/clk/sunxi-ng/Kconfig
> +++ b/drivers/clk/sunxi-ng/Kconfig
> @@ -157,6 +157,16 @@ config SUN8I_DE2_CCU
> select SUNXI_CCU_DIV
> select SUNXI_CCU_GATE
>
> +config SUN8I_R40_CCU
> + bool "Support for the Allwinner R40 CCU"
> + select SUNXI_CCU_DIV
> + select SUNXI_CCU_NK
> + select SUNXI_CCU_NKM
> + select SUNXI_CCU_NKMP
> + select SUNXI_CCU_NM
> + select SUNXI_CCU_MP
You seem to be missing a few, such as CCU_GATE, CCU_MUX, CCU_PHASE.
The list should at least be the same as the included headers.
> + default MACH_SUN8I
> +
> config SUN9I_A80_CCU
> bool "Support for the Allwinner A80 CCU"
> select SUNXI_CCU_DIV
> diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
> index 0185c6ffadcb..217db667a994 100644
> --- a/drivers/clk/sunxi-ng/Makefile
> +++ b/drivers/clk/sunxi-ng/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
> obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
> obj-$(CONFIG_SUN8I_DE2_CCU) += ccu-sun8i-de2.o
> obj-$(CONFIG_SUN8I_R_CCU) += ccu-sun8i-r.o
> +obj-$(CONFIG_SUN8I_R40_CCU) += ccu-sun8i-r40.o
> obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80.o
> obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-de.o
> obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-usb.o
> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.c b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
> new file mode 100644
> index 000000000000..484a8956f59c
> --- /dev/null
> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
> @@ -0,0 +1,1153 @@
> +/*
> + * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/of_address.h>
> +
> +#include "ccu_common.h"
> +#include "ccu_reset.h"
> +
> +#include "ccu_div.h"
> +#include "ccu_gate.h"
> +#include "ccu_mp.h"
> +#include "ccu_mult.h"
> +#include "ccu_nk.h"
> +#include "ccu_nkm.h"
> +#include "ccu_nkmp.h"
> +#include "ccu_nm.h"
> +#include "ccu_phase.h"
> +
> +#include "ccu-sun8i-r40.h"
> +
> +static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpu_clk, "pll-cpu",
> + "osc24M", 0x000,
> + 8, 5, /* N */
> + 4, 2, /* K */
> + 0, 2, /* M */
> + 16, 2, /* P */
P does not do /8. Please add a limit.
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +/*
> + * The Audio PLL is supposed to have 4 outputs: 3 fixed factors from
> + * the base (2x, 4x and 8x), and one variable divider (the one true
> + * pll audio).
> + *
> + * We don't have any need for the variable divider for now, so we just
> + * hardcode it to match with the clock names
> + */
> +#define SUN8I_R40_PLL_AUDIO_REG 0x008
> +
> +static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
> + "osc24M", 0x008,
> + 8, 7, /* N */
> + 0, 5, /* M */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video0_clk, "pll-video0",
> + "osc24M", 0x0010,
> + 8, 7, /* N */
> + 0, 4, /* M */
> + BIT(24), /* frac enable */
> + BIT(25), /* frac select */
> + 270000000, /* frac rate 0 */
> + 297000000, /* frac rate 1 */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_ve_clk, "pll-ve",
> + "osc24M", 0x0018,
> + 8, 7, /* N */
> + 0, 4, /* M */
> + BIT(24), /* frac enable */
> + BIT(25), /* frac select */
> + 270000000, /* frac rate 0 */
> + 297000000, /* frac rate 1 */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_ddr0_clk, "pll-ddr0",
> + "osc24M", 0x020,
> + 8, 5, /* N */
> + 4, 2, /* K */
> + 0, 2, /* M */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +/* According to the BSP driver, pll-periph{0,1} have M at 0:1 */
This is also mentioned in the user manual. You can leave it out.
Also, please leave a note mentioning that support for the SATA clock
output of the peripheral PLL is not implemented here.
> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_periph0_clk, "pll-periph0",
> + "osc24M", 0x028,
> + 8, 5, /* N */
> + 4, 2, /* K */
> + 0, 2, /* M */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_periph1_clk, "pll-periph1",
> + "osc24M", 0x02c,
> + 8, 5, /* N */
> + 4, 2, /* K */
> + 0, 2, /* M */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video1_clk, "pll-video1",
> + "osc24M", 0x030,
> + 8, 7, /* N */
> + 0, 4, /* M */
> + BIT(24), /* frac enable */
> + BIT(25), /* frac select */
> + 270000000, /* frac rate 0 */
> + 297000000, /* frac rate 1 */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + CLK_SET_RATE_UNGATE);
Why do you have this set for only some of the PLLs? Either you need it
for all of them, or you don't need it for any of them.
> +
> +/*
> + * For the special bit in gate part, please see the BSP source code at
> + * https://github.com/BPI-SINOVOIP/BPI-M2U-bsp/blob/master/linux-sunxi/drivers/clk/sunxi/clk-sun8iw11.c#L665
> + */
> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_sata_clk, "pll-sata",
> + "osc24M", 0x034,
> + 8, 5, /* N */
> + 4, 2, /* K */
> + 0, 2, /* M */
> + BIT(31) | BIT(14), /* gate */
> + BIT(28), /* lock */
> + 0);
I think this is a somewhat simplified approach. From what I understand
of the user manual, the SATA clock path look like:
[ PLL-PERIPH0-SATA ] -\
mux @ 0x34 bit 30 --- gate @ 0x34 bit 14 --- ...
[ PLL-SATA ] ---------/
... from above ... ------\
mux @ 0xc8 bit 24 --- gate @ 0xc8 bit 31
[ external oscillator ] -/
If you choose to simplify the implementation, please include a detailed
note as to why you chose to do so, and the validity of the simplification.
> +
> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_gpu_clk, "pll-gpu",
> + "osc24M", 0x038,
> + 8, 7, /* N */
> + 0, 4, /* M */
> + BIT(24), /* frac enable */
> + BIT(25), /* frac select */
> + 270000000, /* frac rate 0 */
> + 297000000, /* frac rate 1 */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static const char * const pll_mipi_parents[] = { "pll-video0", "pll-video1" };
pll-video1 is not listed in the manual.
> +static SUNXI_CCU_NKM_WITH_MUX_GATE_LOCK(pll_mipi_clk, "pll-mipi",
> + pll_mipi_parents, 0x040,
> + 8, 4, /* N */
> + 4, 2, /* K */
> + 0, 4, /* M */
> + 21, 0, /* mux */
> + BIT(31) | BIT(23) | BIT(22), /* gate */
> + BIT(28), /* lock */
> + CLK_SET_RATE_UNGATE);
Please leave a note mentioning that you only implement support for the "MIPI" mode.
You should also force it at probe time. See the driver for the A31.
> +
> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
> + "osc24M", 0x0048,
> + 8, 7, /* N */
> + 0, 4, /* M */
> + BIT(24), /* frac enable */
> + BIT(25), /* frac select */
> + 270000000, /* frac rate 0 */
> + 297000000, /* frac rate 1 */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + 0);
> +
> +static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
> + "osc24M", 0x04c,
> + 8, 7, /* N */
N has minimum and maximum limits.
> + 0, 2, /* M */
> + BIT(31), /* gate */
> + BIT(28), /* lock */
> + CLK_SET_RATE_UNGATE);
> +
> +static const char * const cpu_parents[] = { "osc32k", "osc24M",
> + "pll-cpu", "pll-cpu" };
> +static SUNXI_CCU_MUX(cpu_clk, "cpu", cpu_parents,
> + 0x050, 16, 2, CLK_IS_CRITICAL);
> +
> +static SUNXI_CCU_M(axi_clk, "axi", "cpu", 0x050, 0, 2, 0);
> +
> +static const char * const ahb1_parents[] = { "osc32k", "osc24M",
> + "axi", "pll-periph0" };
> +static const struct ccu_mux_var_prediv ahb1_predivs[] = {
> + { .index = 3, .shift = 6, .width = 2 },
> +};
> +static struct ccu_div ahb1_clk = {
> + .div = _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
> +
> + .mux = {
> + .shift = 12,
> + .width = 2,
> +
> + .var_predivs = ahb1_predivs,
> + .n_var_predivs = ARRAY_SIZE(ahb1_predivs),
> + },
> +
> + .common = {
> + .reg = 0x054,
> + .features = CCU_FEATURE_VARIABLE_PREDIV,
> + .hw.init = CLK_HW_INIT_PARENTS("ahb1",
> + ahb1_parents,
> + &ccu_div_ops,
> + 0),
> + },
> +};
> +
> +static struct clk_div_table apb1_div_table[] = {
> + { .val = 0, .div = 2 },
> + { .val = 1, .div = 2 },
> + { .val = 2, .div = 4 },
> + { .val = 3, .div = 8 },
> + { /* Sentinel */ },
> +};
> +static SUNXI_CCU_DIV_TABLE(apb1_clk, "apb1", "ahb1",
> + 0x054, 8, 2, apb1_div_table, 0);
> +
> +static const char * const apb2_parents[] = { "osc32k", "osc24M",
> + "pll-periph0-2x",
> + "pll-periph0-2x" };
> +static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", apb2_parents, 0x058,
> + 0, 5, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + 0);
> +
> +static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb1",
> + 0x060, BIT(1), 0);
> +static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "ahb1",
> + 0x060, BIT(5), 0);
> +static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "ahb1",
> + 0x060, BIT(6), 0);
> +static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb1",
> + 0x060, BIT(8), 0);
> +static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb1",
> + 0x060, BIT(9), 0);
> +static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb1",
> + 0x060, BIT(10), 0);
> +static SUNXI_CCU_GATE(bus_mmc3_clk, "bus-mmc3", "ahb1",
> + 0x060, BIT(11), 0);
> +static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb1",
> + 0x060, BIT(13), 0);
> +static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "ahb1",
> + 0x060, BIT(14), 0);
> +static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb1",
> + 0x060, BIT(17), 0);
> +static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb1",
> + 0x060, BIT(18), 0);
> +static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "ahb1",
> + 0x060, BIT(19), 0);
> +static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb1",
> + 0x060, BIT(20), 0);
> +static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb1",
> + 0x060, BIT(21), 0);
> +static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb1",
> + 0x060, BIT(22), 0);
> +static SUNXI_CCU_GATE(bus_spi3_clk, "bus-spi3", "ahb1",
> + 0x060, BIT(23), 0);
> +static SUNXI_CCU_GATE(bus_sata_clk, "bus-sata", "ahb1",
> + 0x060, BIT(24), 0);
> +static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb1",
> + 0x060, BIT(25), 0);
> +static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb1",
> + 0x060, BIT(26), 0);
> +static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb1",
> + 0x060, BIT(27), 0);
> +static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb1",
> + 0x060, BIT(28), 0);
> +static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb1",
> + 0x060, BIT(29), 0);
> +static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb1",
> + 0x060, BIT(30), 0);
> +static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb1",
> + 0x060, BIT(31), 0);
> +
> +static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "ahb1",
> + 0x064, BIT(0), 0);
> +static SUNXI_CCU_GATE(bus_de_mp_clk, "bus-de-mp", "ahb1",
> + 0x064, BIT(2), 0);
The mixer processor is unrelated to the display engine.
Please drop the "de" part of the name.
> +static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "ahb1",
> + 0x064, BIT(5), 0);
> +static SUNXI_CCU_GATE(bus_csi0_clk, "bus-csi0", "ahb1",
> + 0x064, BIT(8), 0);
> +static SUNXI_CCU_GATE(bus_csi1_clk, "bus-csi1", "ahb1",
> + 0x064, BIT(9), 0);
> +static SUNXI_CCU_GATE(bus_hdmi_slow_clk, "bus-hdmi-slow", "ahb1",
> + 0x064, BIT(10), 0);
> +static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb1",
> + 0x064, BIT(11), 0);
Please stick to the names in the user manual.
They are hdmi0 and hdmi1.
> +static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "ahb1",
> + 0x064, BIT(12), 0);
> +static SUNXI_CCU_GATE(bus_tve0_clk, "bus-tve0", "ahb1",
> + 0x064, BIT(13), 0);
> +static SUNXI_CCU_GATE(bus_tve1_clk, "bus-tve1", "ahb1",
> + 0x064, BIT(14), 0);
> +static SUNXI_CCU_GATE(bus_tve_top_clk, "bus-tve-top", "ahb1",
> + 0x064, BIT(15), 0);
> +static SUNXI_CCU_GATE(bus_gmac_clk, "bus-gmac", "ahb1",
> + 0x064, BIT(17), 0);
> +static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "ahb1",
> + 0x064, BIT(20), 0);
> +static SUNXI_CCU_GATE(bus_tvd0_clk, "bus-tvd0", "ahb1",
> + 0x064, BIT(21), 0);
> +static SUNXI_CCU_GATE(bus_tvd1_clk, "bus-tvd1", "ahb1",
> + 0x064, BIT(22), 0);
> +static SUNXI_CCU_GATE(bus_tvd2_clk, "bus-tvd2", "ahb1",
> + 0x064, BIT(23), 0);
> +static SUNXI_CCU_GATE(bus_tvd3_clk, "bus-tvd3", "ahb1",
> + 0x064, BIT(24), 0);
> +static SUNXI_CCU_GATE(bus_tvd_top_clk, "bus-tvd-top", "ahb1",
> + 0x064, BIT(25), 0);
> +static SUNXI_CCU_GATE(bus_tcon0_clk, "bus-tcon0", "ahb1",
> + 0x064, BIT(26), 0);
> +static SUNXI_CCU_GATE(bus_tcon1_clk, "bus-tcon1", "ahb1",
> + 0x064, BIT(27), 0);
> +static SUNXI_CCU_GATE(bus_tve0_tcon_clk, "bus-tve0-tcon", "ahb1",
> + 0x064, BIT(28), 0);
> +static SUNXI_CCU_GATE(bus_tve1_tcon_clk, "bus-tve1-tcon", "ahb1",
> + 0x064, BIT(29), 0);
Please stick to the names used in the user manual.
They are "tcon-lcdN" and "tcon-tvN".
> +static SUNXI_CCU_GATE(bus_tcon_top_clk, "bus-tcon-top", "ahb1",
> + 0x064, BIT(30), 0);
> +
> +static SUNXI_CCU_GATE(bus_codec_clk, "bus-codec", "apb1",
> + 0x068, BIT(0), 0);
> +static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1",
> + 0x068, BIT(1), 0);
> +static SUNXI_CCU_GATE(bus_ac97_clk, "bus-ac97", "apb1",
> + 0x068, BIT(2), 0);
> +static SUNXI_CCU_GATE(bus_pio_clk, "bus-pio", "apb1",
> + 0x068, BIT(5), 0);
> +static SUNXI_CCU_GATE(bus_ir0_clk, "bus-ir0", "apb1",
> + 0x068, BIT(6), 0);
> +static SUNXI_CCU_GATE(bus_ir1_clk, "bus-ir1", "apb1",
> + 0x068, BIT(7), 0);
> +static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1",
> + 0x068, BIT(8), 0);
> +static SUNXI_CCU_GATE(bus_keypad_clk, "bus-keypad", "apb1",
> + 0x068, BIT(10), 0);
> +static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1",
> + 0x068, BIT(12), 0);
> +static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1",
> + 0x068, BIT(13), 0);
> +static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1",
> + 0x068, BIT(14), 0);
> +
> +static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2",
> + 0x06c, BIT(0), 0);
> +static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2",
> + 0x06c, BIT(1), 0);
> +static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2",
> + 0x06c, BIT(2), 0);
> +static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2",
> + 0x06c, BIT(3), 0);
> +/*
> + * In datasheet here's "Reserved", however the gate exists in BSP soucre
> + * code.
> + */
> +static SUNXI_CCU_GATE(bus_can_clk, "bus-can", "apb2",
> + 0x06c, BIT(4), 0);
> +static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
> + 0x06c, BIT(5), 0);
> +static SUNXI_CCU_GATE(bus_ps20_clk, "bus-ps20", "apb2",
> + 0x06c, BIT(6), 0);
> +static SUNXI_CCU_GATE(bus_ps21_clk, "bus-ps21", "apb2",
> + 0x06c, BIT(7), 0);
> +static SUNXI_CCU_GATE(bus_i2c4_clk, "bus-i2c4", "apb2",
> + 0x06c, BIT(15), 0);
> +static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2",
> + 0x06c, BIT(16), 0);
> +static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2",
> + 0x06c, BIT(17), 0);
> +static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
> + 0x06c, BIT(18), 0);
> +static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
> + 0x06c, BIT(19), 0);
> +static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2",
> + 0x06c, BIT(20), 0);
> +static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2",
> + 0x06c, BIT(21), 0);
> +static SUNXI_CCU_GATE(bus_uart6_clk, "bus-uart6", "apb2",
> + 0x06c, BIT(22), 0);
> +static SUNXI_CCU_GATE(bus_uart7_clk, "bus-uart7", "apb2",
> + 0x06c, BIT(23), 0);
> +
> +/* Educated guess: the BSP clock driver do not have this clock */
The gate is documented in the user manual. What part is a guess?
> +static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "ahb1",
> + 0x070, BIT(7), 0);
> +
> +static SUNXI_CCU_M_WITH_GATE(ths_clk, "ths", "osc24M",
> + 0x074, 0, 2, BIT(31), 0);
This clock has a mux. Even with only one parent, you should still
implement the mux, so the kernel can recover from cases where some
other piece of software left it in a bad state.
Also the divider is of the power of two type.
> +
> +static const char * const mod0_default_parents[] = { "osc24M", "pll-periph0",
> + "pll-periph1" };
> +static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand", mod0_default_parents, 0x080,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mod0_default_parents, 0x088,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mod0_default_parents, 0x08c,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mod0_default_parents, 0x090,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc3_clk, "mmc3", mod0_default_parents, 0x094,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static const char * const ts_parents[] = { "osc24M", "pll-periph0", };
> +static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x098,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
The mux is 4 bits wide.
> + BIT(31), /* gate */
> + 0);
> +
> +static const char * const ce_parents[] = { "osc24M", "pll-periph0-2x",
> + "pll-periph1-2x" };
> +static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x09c,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", mod0_default_parents, 0x0a0,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_default_parents, 0x0a4,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", mod0_default_parents, 0x0a8,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi3_clk, "spi3", mod0_default_parents, 0x0ac,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static const char * const i2s_parents[] = { "pll-audio-8x", "pll-audio-4x",
> + "pll-audio-2x", "pll-audio" };
> +static SUNXI_CCU_MUX_WITH_GATE(i2s0_clk, "i2s0", i2s_parents,
> + 0x0b0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
> +
> +static SUNXI_CCU_MUX_WITH_GATE(i2s1_clk, "i2s1", i2s_parents,
> + 0x0b4, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
> +
> +static SUNXI_CCU_MUX_WITH_GATE(i2s2_clk, "i2s2", i2s_parents,
> + 0x0b8, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
> +
> +static SUNXI_CCU_MUX_WITH_GATE(ac97_clk, "ac97", i2s_parents,
> + 0x0bc, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
> +
> +static SUNXI_CCU_MUX_WITH_GATE(spdif_clk, "spdif", i2s_parents,
> + 0x0c0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
> +
> +static const char * const keypad_parents[] = { "osc24M", "osc32k", };
The parents are not sequential. You need a mux table here.
> +static SUNXI_CCU_MP_WITH_MUX_GATE(keypad_clk, "keypad", keypad_parents, 0x0c4,
> + 0, 5, /* M */
> + 16, 2, /* P */
> + 25, 1, /* mux */
Mux is 2 bits wide.
> + BIT(31), /* gate */
> + 0);
> +
> +static const char * const sata_parents[] = { "pll-sata", "sata-ext", };
> +static SUNXI_CCU_MUX_WITH_GATE(sata_clk, "sata", sata_parents,
> + 0x0c8, 24, 1, BIT(31), CLK_SET_RATE_PARENT);
> +
> +static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M",
> + 0x0cc, BIT(8), 0);
> +static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M",
> + 0x0cc, BIT(9), 0);
> +static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M",
> + 0x0cc, BIT(10), 0);
> +static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc24M",
> + 0x0cc, BIT(16), 0);
> +static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc24M",
> + 0x0cc, BIT(17), 0);
> +static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc24M",
> + 0x0cc, BIT(18), 0);
Why bother with the 3 clocks below, if you aren't going to use them as parents
for the 3 usb-ohci gates above? The user manual states the gates are for both
48M and 12M clocks.
> +
> +static const char * const usb_ohci12m_parents[] = { "osc24M-2x", "osc24M",
> + "osc32k" };
You should have pre-dividers here so the clk subsystem can report correct
clk rates.
> +static SUNXI_CCU_MUX(usb_ohci0_12m_clk, "usb-ohci0-12m", usb_ohci12m_parents,
> + 0x0cc, 20, 2, 0);
> +static SUNXI_CCU_MUX(usb_ohci1_12m_clk, "usb-ohci1-12m", usb_ohci12m_parents,
> + 0x0cc, 22, 2, 0);
> +static SUNXI_CCU_MUX(usb_ohci2_12m_clk, "usb-ohci2-12m", usb_ohci12m_parents,
> + 0x0cc, 24, 2, 0);
> +
> +static const char * const ir_parents[] = { "osc24M", "pll-periph0",
> + "pll-periph1", "osc32k" };
> +static SUNXI_CCU_MP_WITH_MUX_GATE(ir0_clk, "ir0", ir_parents, 0x0d0,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static SUNXI_CCU_MP_WITH_MUX_GATE(ir1_clk, "ir1", ir_parents, 0x0d4,
> + 0, 4, /* M */
> + 16, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1" };
> +static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents,
> + 0x0f4, 0, 2, 20, 2, CLK_IS_CRITICAL);
> +
> +static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram",
> + 0x100, BIT(0), 0);
> +static SUNXI_CCU_GATE(dram_csi0_clk, "dram-csi0", "dram",
> + 0x100, BIT(1), 0);
> +static SUNXI_CCU_GATE(dram_csi1_clk, "dram-csi1", "dram",
> + 0x100, BIT(2), 0);
> +static SUNXI_CCU_GATE(dram_ts_clk, "dram-ts", "dram",
> + 0x100, BIT(3), 0);
> +static SUNXI_CCU_GATE(dram_tvd_clk, "dram-tvd", "dram",
> + 0x100, BIT(4), 0);
> +static SUNXI_CCU_GATE(dram_de_mp_clk, "dram-de-mp", "dram",
> + 0x100, BIT(5), 0);
Same thing about the mixer processor as before.
> +static SUNXI_CCU_GATE(dram_deinterlace_clk, "dram-deinterlace", "dram",
> + 0x100, BIT(6), 0);
> +
> +static const char * const de_parents[] = { "pll-periph0-2x", "pll-de" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents,
> + 0x104, 0, 4, 24, 3, BIT(31), 0);
> +static SUNXI_CCU_M_WITH_MUX_GATE(de_mp_clk, "de-mp", de_parents,
> + 0x108, 0, 4, 24, 3, BIT(31), 0);
> +
> +static const char * const tcon_parents[] = { "pll-video0", "pll-video1",
> + "pll-video0-2x", "pll-video1-2x",
> + "pll-mipi" };
> +static SUNXI_CCU_MUX_WITH_GATE(tcon0_clk, "tcon0", tcon_parents,
> + 0x110, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
> +static SUNXI_CCU_MUX_WITH_GATE(tcon1_clk, "tcon1", tcon_parents,
> + 0x114, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
> +static SUNXI_CCU_M_WITH_MUX_GATE(tcon_tve0_clk, "tcon-tve0", tcon_parents,
> + 0x118, 0, 4, 24, 3, BIT(31), 0);
> +static SUNXI_CCU_M_WITH_MUX_GATE(tcon_tve1_clk, "tcon-tve1", tcon_parents,
> + 0x11c, 0, 4, 24, 3, BIT(31), 0);
Again, please stick to the names used by the user manual.
> +
> +static const char * const deinterlace_parents[] = { "pll-periph0",
> + "pll-periph1" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace",
> + deinterlace_parents, 0x124, 0, 4, 24, 3,
> + BIT(31), 0);
> +
> +static const char * const csi_mclk_parents[] = { "osc24M", "pll-video",
> + "pll-periph1" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk", csi_mclk_parents,
> + 0x130, 0, 5, 8, 3, BIT(15), 0);
> +
> +static const char * const csi_sclk_parents[] = { "pll-periph0", "pll-periph1" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(csi_sclk_clk, "csi-sclk", csi_sclk_parents,
> + 0x134, 16, 4, 24, 3, BIT(31), 0);
> +
> +static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk", csi_mclk_parents,
> + 0x134, 0, 5, 8, 3, BIT(15), 0);
> +
> +static SUNXI_CCU_M_WITH_GATE(ve_clk, "ve", "pll-ve",
> + 0x13c, 16, 3, BIT(31), 0);
> +
> +static SUNXI_CCU_GATE(adda_clk, "adda", "pll-audio",
> + 0x140, BIT(31), CLK_SET_RATE_PARENT);
> +static SUNXI_CCU_GATE(adda_4x_clk, "adda-4x", "pll-audio-4x",
> + 0x140, BIT(30), CLK_SET_RATE_PARENT);
adda-4x is not listed in the user manual. Does it really exist?
Is it used anywhere?
> +static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M",
> + 0x144, BIT(31), 0);
> +
> +static const char * const hdmi_parents[] = { "pll-video0", "pll-video1" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents,
> + 0x150, 0, 4, 24, 2, BIT(31), 0);
> +
> +static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M",
> + 0x154, BIT(31), 0);
> +
> +static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x",
> + "pll-ddr0" };
> +static SUNXI_CCU_MP_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x15c,
> + 0, 4, /* M */
> + 16, 2, /* P */
Curiously, the formula for clk rate calculation does not include this
factor.
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + CLK_IS_CRITICAL);
> +
> +static const char * const mipi_dsi_parents[] = { "pll-video0", "pll-video1",
> + "pll-periph0" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi", mipi_dsi_parents,
> + 0x168, 0, 4, 8, 2, BIT(15), 0);
This is called "dsi-dphy" in the user manual. Looking at the A31,
it had "dsi-sclk" in the upper 16 bits. So please use "dsi-dphy"
or "mipi-dsi-dphy" here.
> +
> +static SUNXI_CCU_M_WITH_MUX_GATE(tve0_clk, "tve0", tcon_parents,
> + 0x180, 0, 4, 24, 3, BIT(31), 0);
> +static SUNXI_CCU_M_WITH_MUX_GATE(tve1_clk, "tve1", tcon_parents,
> + 0x184, 0, 4, 24, 3, BIT(31), 0);
> +
> +static const char * const tvd_parents[] = { "pll-video0", "pll-video1",
> + "pll-video0-2x", "pll-video1-2x" };
> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd0_clk, "tvd0", tvd_parents,
> + 0x188, 0, 4, 24, 2, BIT(31), 0);
> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd1_clk, "tvd1", tvd_parents,
> + 0x18c, 0, 4, 24, 2, BIT(31), 0);
> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd2_clk, "tvd2", tvd_parents,
> + 0x190, 0, 4, 24, 2, BIT(31), 0);
> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd3_clk, "tvd3", tvd_parents,
> + 0x194, 0, 4, 24, 2, BIT(31), 0);
The mux is 3 bits wide for the tvd clocks.
> +
> +static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
> + 0x1a0, 0, 3, BIT(31), 0);
You should probably have CLK_SET_RATE_PARENT here.
> +
> +static const char * const out_parents[] = { "osc24M-32k", "osc32k", "osc24M" };
Please use pre-dividers instead of "osc24M-32k".
> +static SUNXI_CCU_MP_WITH_MUX_GATE(outa_clk, "outa", out_parents, 0x1f0,
> + 8, 5, /* M */
> + 20, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +static SUNXI_CCU_MP_WITH_MUX_GATE(outb_clk, "outb", out_parents, 0x1f4,
> + 8, 5, /* M */
> + 20, 2, /* P */
> + 24, 2, /* mux */
> + BIT(31), /* gate */
> + 0);
> +
> +static struct ccu_common *sun8i_r40_ccu_clks[] = {
> + &pll_cpu_clk.common,
> + &pll_audio_base_clk.common,
> + &pll_video0_clk.common,
> + &pll_ve_clk.common,
> + &pll_ddr0_clk.common,
> + &pll_periph0_clk.common,
> + &pll_periph1_clk.common,
> + &pll_video1_clk.common,
> + &pll_sata_clk.common,
> + &pll_gpu_clk.common,
> + &pll_mipi_clk.common,
> + &pll_de_clk.common,
> + &pll_ddr1_clk.common,
> + &cpu_clk.common,
> + &axi_clk.common,
> + &ahb1_clk.common,
> + &apb1_clk.common,
> + &apb2_clk.common,
> + &bus_mipi_dsi_clk.common,
> + &bus_ce_clk.common,
> + &bus_dma_clk.common,
> + &bus_mmc0_clk.common,
> + &bus_mmc1_clk.common,
> + &bus_mmc2_clk.common,
> + &bus_mmc3_clk.common,
> + &bus_nand_clk.common,
> + &bus_dram_clk.common,
> + &bus_emac_clk.common,
> + &bus_ts_clk.common,
> + &bus_hstimer_clk.common,
> + &bus_spi0_clk.common,
> + &bus_spi1_clk.common,
> + &bus_spi2_clk.common,
> + &bus_spi3_clk.common,
> + &bus_sata_clk.common,
> + &bus_otg_clk.common,
> + &bus_ehci0_clk.common,
> + &bus_ehci1_clk.common,
> + &bus_ehci2_clk.common,
> + &bus_ohci0_clk.common,
> + &bus_ohci1_clk.common,
> + &bus_ohci2_clk.common,
> + &bus_ve_clk.common,
> + &bus_de_mp_clk.common,
> + &bus_deinterlace_clk.common,
> + &bus_csi0_clk.common,
> + &bus_csi1_clk.common,
> + &bus_hdmi_slow_clk.common,
> + &bus_hdmi_clk.common,
> + &bus_de_clk.common,
> + &bus_tve0_clk.common,
> + &bus_tve1_clk.common,
> + &bus_tve_top_clk.common,
> + &bus_gmac_clk.common,
> + &bus_gpu_clk.common,
> + &bus_tvd0_clk.common,
> + &bus_tvd1_clk.common,
> + &bus_tvd2_clk.common,
> + &bus_tvd3_clk.common,
> + &bus_tvd_top_clk.common,
> + &bus_tcon0_clk.common,
> + &bus_tcon1_clk.common,
> + &bus_tve0_tcon_clk.common,
> + &bus_tve1_tcon_clk.common,
> + &bus_tcon_top_clk.common,
> + &bus_codec_clk.common,
> + &bus_spdif_clk.common,
> + &bus_ac97_clk.common,
> + &bus_pio_clk.common,
> + &bus_ir0_clk.common,
> + &bus_ir1_clk.common,
> + &bus_ths_clk.common,
> + &bus_keypad_clk.common,
> + &bus_i2s0_clk.common,
> + &bus_i2s1_clk.common,
> + &bus_i2s2_clk.common,
> + &bus_i2c0_clk.common,
> + &bus_i2c1_clk.common,
> + &bus_i2c2_clk.common,
> + &bus_i2c3_clk.common,
> + &bus_can_clk.common,
> + &bus_scr_clk.common,
> + &bus_ps20_clk.common,
> + &bus_ps21_clk.common,
> + &bus_i2c4_clk.common,
> + &bus_uart0_clk.common,
> + &bus_uart1_clk.common,
> + &bus_uart2_clk.common,
> + &bus_uart3_clk.common,
> + &bus_uart4_clk.common,
> + &bus_uart5_clk.common,
> + &bus_uart6_clk.common,
> + &bus_uart7_clk.common,
> + &bus_dbg_clk.common,
> + &ths_clk.common,
> + &nand_clk.common,
> + &mmc0_clk.common,
> + &mmc1_clk.common,
> + &mmc2_clk.common,
> + &mmc3_clk.common,
> + &ts_clk.common,
> + &ce_clk.common,
> + &spi0_clk.common,
> + &spi1_clk.common,
> + &spi2_clk.common,
> + &spi3_clk.common,
> + &i2s0_clk.common,
> + &i2s1_clk.common,
> + &i2s2_clk.common,
> + &ac97_clk.common,
> + &spdif_clk.common,
> + &keypad_clk.common,
> + &sata_clk.common,
> + &usb_phy0_clk.common,
> + &usb_phy1_clk.common,
> + &usb_phy2_clk.common,
> + &usb_ohci0_clk.common,
> + &usb_ohci1_clk.common,
> + &usb_ohci2_clk.common,
> + &usb_ohci0_12m_clk.common,
> + &usb_ohci1_12m_clk.common,
> + &usb_ohci2_12m_clk.common,
> + &ir0_clk.common,
> + &ir1_clk.common,
> + &dram_clk.common,
> + &dram_ve_clk.common,
> + &dram_csi0_clk.common,
> + &dram_csi1_clk.common,
> + &dram_ts_clk.common,
> + &dram_tvd_clk.common,
> + &dram_de_mp_clk.common,
> + &dram_deinterlace_clk.common,
> + &de_clk.common,
> + &de_mp_clk.common,
> + &tcon0_clk.common,
> + &tcon1_clk.common,
> + &tcon_tve0_clk.common,
> + &tcon_tve1_clk.common,
> + &deinterlace_clk.common,
> + &csi1_mclk_clk.common,
> + &csi_sclk_clk.common,
> + &csi0_mclk_clk.common,
> + &ve_clk.common,
> + &adda_clk.common,
> + &adda_4x_clk.common,
> + &avs_clk.common,
> + &hdmi_clk.common,
> + &hdmi_slow_clk.common,
> + &mbus_clk.common,
> + &mipi_dsi_clk.common,
> + &tve0_clk.common,
> + &tve1_clk.common,
> + &tvd0_clk.common,
> + &tvd1_clk.common,
> + &tvd2_clk.common,
> + &tvd3_clk.common,
> + &gpu_clk.common,
> + &outa_clk.common,
> + &outb_clk.common,
> +};
> +
> +/* We hardcode the divider to 4 for now */
> +static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
> + "pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
> +static CLK_FIXED_FACTOR(pll_audio_2x_clk, "pll-audio-2x",
> + "pll-audio-base", 2, 1, CLK_SET_RATE_PARENT);
> +static CLK_FIXED_FACTOR(pll_audio_4x_clk, "pll-audio-4x",
> + "pll-audio-base", 1, 1, CLK_SET_RATE_PARENT);
> +static CLK_FIXED_FACTOR(pll_audio_8x_clk, "pll-audio-8x",
> + "pll-audio-base", 1, 2, CLK_SET_RATE_PARENT);
> +static CLK_FIXED_FACTOR(pll_periph0_2x_clk, "pll-periph0-2x",
> + "pll-periph0", 1, 2, 0);
> +static CLK_FIXED_FACTOR(pll_periph1_2x_clk, "pll-periph1-2x",
> + "pll-periph1", 1, 2, 0);
> +static CLK_FIXED_FACTOR(pll_video0_2x_clk, "pll-video0-2x",
> + "pll-video0", 1, 2, 0);
> +static CLK_FIXED_FACTOR(pll_video1_2x_clk, "pll-video1-2x",
> + "pll-video1", 1, 2, 0);
> +static CLK_FIXED_FACTOR(osc24m_2x_clk, "osc24M-2x",
> + "osc24M", 1, 2, 0);
> +static CLK_FIXED_FACTOR(osc24m_32k_clk, "osc24M-32k",
> + "osc24M", 750, 1, 0);
As mentioned above, please drop the last one.
> +
> +static struct clk_hw_onecell_data sun8i_r40_hw_clks = {
> + .hws = {
> + [CLK_OSC24M_2X] = &osc24m_2x_clk.hw,
> + [CLK_OSC24M_32K] = &osc24m_32k_clk.hw,
> + [CLK_PLL_CPU] = &pll_cpu_clk.common.hw,
> + [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
> + [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
> + [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
> + [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
> + [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
> + [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
> + [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
> + [CLK_PLL_VE] = &pll_ve_clk.common.hw,
> + [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
> + [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
> + [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
> + [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
> + [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
> + [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
> + [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
> + [CLK_PLL_SATA] = &pll_sata_clk.common.hw,
> + [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
> + [CLK_PLL_MIPI] = &pll_mipi_clk.common.hw,
> + [CLK_PLL_DE] = &pll_de_clk.common.hw,
> + [CLK_PLL_DDR1] = &pll_ddr1_clk.common.hw,
> + [CLK_CPU] = &cpu_clk.common.hw,
> + [CLK_AXI] = &axi_clk.common.hw,
> + [CLK_AHB1] = &ahb1_clk.common.hw,
> + [CLK_APB1] = &apb1_clk.common.hw,
> + [CLK_APB2] = &apb2_clk.common.hw,
> + [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
> + [CLK_BUS_CE] = &bus_ce_clk.common.hw,
> + [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
> + [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
> + [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
> + [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
> + [CLK_BUS_MMC3] = &bus_mmc3_clk.common.hw,
> + [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
> + [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
> + [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
> + [CLK_BUS_TS] = &bus_ts_clk.common.hw,
> + [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
> + [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
> + [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
> + [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
> + [CLK_BUS_SPI3] = &bus_spi3_clk.common.hw,
> + [CLK_BUS_SATA] = &bus_sata_clk.common.hw,
> + [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
> + [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
> + [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
> + [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
> + [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
> + [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
> + [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
> + [CLK_BUS_VE] = &bus_ve_clk.common.hw,
> + [CLK_BUS_DE_MP] = &bus_de_mp_clk.common.hw,
> + [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
> + [CLK_BUS_CSI0] = &bus_csi0_clk.common.hw,
> + [CLK_BUS_CSI1] = &bus_csi1_clk.common.hw,
> + [CLK_BUS_HDMI_SLOW] = &bus_hdmi_slow_clk.common.hw,
> + [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
> + [CLK_BUS_DE] = &bus_de_clk.common.hw,
> + [CLK_BUS_TVE0] = &bus_tve0_clk.common.hw,
> + [CLK_BUS_TVE1] = &bus_tve1_clk.common.hw,
> + [CLK_BUS_TVE_TOP] = &bus_tve_top_clk.common.hw,
> + [CLK_BUS_GMAC] = &bus_gmac_clk.common.hw,
> + [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
> + [CLK_BUS_TVD0] = &bus_tvd0_clk.common.hw,
> + [CLK_BUS_TVD1] = &bus_tvd1_clk.common.hw,
> + [CLK_BUS_TVD2] = &bus_tvd2_clk.common.hw,
> + [CLK_BUS_TVD3] = &bus_tvd3_clk.common.hw,
> + [CLK_BUS_TVD_TOP] = &bus_tvd_top_clk.common.hw,
> + [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
> + [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
> + [CLK_BUS_TVE0_TCON] = &bus_tve0_tcon_clk.common.hw,
> + [CLK_BUS_TVE1_TCON] = &bus_tve1_tcon_clk.common.hw,
> + [CLK_BUS_TCON_TOP] = &bus_tcon_top_clk.common.hw,
> + [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
> + [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
> + [CLK_BUS_AC97] = &bus_ac97_clk.common.hw,
> + [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
> + [CLK_BUS_IR0] = &bus_ir0_clk.common.hw,
> + [CLK_BUS_IR1] = &bus_ir1_clk.common.hw,
> + [CLK_BUS_THS] = &bus_ths_clk.common.hw,
> + [CLK_BUS_KEYPAD] = &bus_keypad_clk.common.hw,
> + [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
> + [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
> + [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
> + [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
> + [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
> + [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
> + [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
> + [CLK_BUS_CAN] = &bus_can_clk.common.hw,
> + [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
> + [CLK_BUS_PS20] = &bus_ps20_clk.common.hw,
> + [CLK_BUS_PS21] = &bus_ps21_clk.common.hw,
> + [CLK_BUS_I2C4] = &bus_i2c4_clk.common.hw,
> + [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
> + [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
> + [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
> + [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
> + [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
> + [CLK_BUS_UART5] = &bus_uart5_clk.common.hw,
> + [CLK_BUS_UART6] = &bus_uart6_clk.common.hw,
> + [CLK_BUS_UART7] = &bus_uart7_clk.common.hw,
> + [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
> + [CLK_THS] = &ths_clk.common.hw,
> + [CLK_NAND] = &nand_clk.common.hw,
> + [CLK_MMC0] = &mmc0_clk.common.hw,
> + [CLK_MMC1] = &mmc1_clk.common.hw,
> + [CLK_MMC2] = &mmc2_clk.common.hw,
> + [CLK_MMC3] = &mmc3_clk.common.hw,
> + [CLK_TS] = &ts_clk.common.hw,
> + [CLK_CE] = &ce_clk.common.hw,
> + [CLK_SPI0] = &spi0_clk.common.hw,
> + [CLK_SPI1] = &spi1_clk.common.hw,
> + [CLK_SPI2] = &spi2_clk.common.hw,
> + [CLK_SPI3] = &spi3_clk.common.hw,
> + [CLK_I2S0] = &i2s0_clk.common.hw,
> + [CLK_I2S1] = &i2s1_clk.common.hw,
> + [CLK_I2S2] = &i2s2_clk.common.hw,
> + [CLK_AC97] = &ac97_clk.common.hw,
> + [CLK_SPDIF] = &spdif_clk.common.hw,
> + [CLK_KEYPAD] = &keypad_clk.common.hw,
> + [CLK_SATA] = &sata_clk.common.hw,
> + [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
> + [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
> + [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
> + [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
> + [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
> + [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
> + [CLK_USB_OHCI0_12M] = &usb_ohci0_12m_clk.common.hw,
> + [CLK_USB_OHCI1_12M] = &usb_ohci1_12m_clk.common.hw,
> + [CLK_USB_OHCI2_12M] = &usb_ohci2_12m_clk.common.hw,
> + [CLK_IR0] = &ir0_clk.common.hw,
> + [CLK_IR1] = &ir1_clk.common.hw,
> + [CLK_DRAM] = &dram_clk.common.hw,
> + [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
> + [CLK_DRAM_CSI0] = &dram_csi0_clk.common.hw,
> + [CLK_DRAM_CSI1] = &dram_csi1_clk.common.hw,
> + [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
> + [CLK_DRAM_TVD] = &dram_tvd_clk.common.hw,
> + [CLK_DRAM_DE_MP] = &dram_de_mp_clk.common.hw,
> + [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
> + [CLK_DE] = &de_clk.common.hw,
> + [CLK_DE_MP] = &de_mp_clk.common.hw,
> + [CLK_TCON0] = &tcon0_clk.common.hw,
> + [CLK_TCON1] = &tcon1_clk.common.hw,
> + [CLK_TCON_TVE0] = &tcon_tve0_clk.common.hw,
> + [CLK_TCON_TVE1] = &tcon_tve1_clk.common.hw,
> + [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
> + [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
> + [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
> + [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
> + [CLK_VE] = &ve_clk.common.hw,
> + [CLK_ADDA] = &adda_clk.common.hw,
> + [CLK_ADDA_4X] = &adda_4x_clk.common.hw,
> + [CLK_AVS] = &avs_clk.common.hw,
> + [CLK_HDMI] = &hdmi_clk.common.hw,
> + [CLK_HDMI_SLOW] = &hdmi_slow_clk.common.hw,
> + [CLK_MBUS] = &mbus_clk.common.hw,
> + [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
> + [CLK_TVE0] = &tve0_clk.common.hw,
> + [CLK_TVE1] = &tve1_clk.common.hw,
> + [CLK_TVD0] = &tvd0_clk.common.hw,
> + [CLK_TVD1] = &tvd1_clk.common.hw,
> + [CLK_TVD2] = &tvd2_clk.common.hw,
> + [CLK_TVD3] = &tvd3_clk.common.hw,
> + [CLK_GPU] = &gpu_clk.common.hw,
> + [CLK_OUTA] = &outa_clk.common.hw,
> + [CLK_OUTB] = &outb_clk.common.hw,
> + },
> + .num = CLK_NUMBER,
> +};
> +
> +static struct ccu_reset_map sun8i_r40_ccu_resets[] = {
> + [RST_USB_PHY0] = { 0x0cc, BIT(0) },
> + [RST_USB_PHY1] = { 0x0cc, BIT(1) },
> + [RST_USB_PHY2] = { 0x0cc, BIT(2) },
> +
There is also a reset control for the DRAM controller at bit 31
of register 0xf4.
> + [RST_MBUS] = { 0x0fc, BIT(31) },
> +
> + [RST_BUS_MIPI_DSI] = { 0x2c0, BIT(1) },
> + [RST_BUS_CE] = { 0x2c0, BIT(5) },
> + [RST_BUS_DMA] = { 0x2c0, BIT(6) },
> + [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
> + [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
> + [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
> + [RST_BUS_MMC3] = { 0x2c0, BIT(11) },
> + [RST_BUS_NAND] = { 0x2c0, BIT(13) },
> + [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
> + [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
> + [RST_BUS_TS] = { 0x2c0, BIT(18) },
> + [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
> + [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
> + [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
> + [RST_BUS_SPI2] = { 0x2c0, BIT(22) },
> + [RST_BUS_SPI3] = { 0x2c0, BIT(23) },
> + [RST_BUS_SATA] = { 0x2c0, BIT(24) },
> + [RST_BUS_OTG] = { 0x2c0, BIT(25) },
> + [RST_BUS_EHCI0] = { 0x2c0, BIT(26) },
> + [RST_BUS_EHCI1] = { 0x2c0, BIT(27) },
> + [RST_BUS_EHCI2] = { 0x2c0, BIT(28) },
> + [RST_BUS_OHCI0] = { 0x2c0, BIT(29) },
> + [RST_BUS_OHCI1] = { 0x2c0, BIT(30) },
> + [RST_BUS_OHCI2] = { 0x2c0, BIT(31) },
> +
> + [RST_BUS_VE] = { 0x2c4, BIT(0) },
> + [RST_BUS_DE_MP] = { 0x2c4, BIT(2) },
Same thing about the MP's name.
> + [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
> + [RST_BUS_CSI0] = { 0x2c4, BIT(8) },
> + [RST_BUS_CSI1] = { 0x2c4, BIT(9) },
> + [RST_BUS_HDMI_SLOW] = { 0x2c4, BIT(10) },
> + [RST_BUS_HDMI] = { 0x2c4, BIT(11) },
Same thing about the HDMI's names.
> + [RST_BUS_DE] = { 0x2c4, BIT(12) },
> + [RST_BUS_TVE0] = { 0x2c4, BIT(13) },
> + [RST_BUS_TVE1] = { 0x2c4, BIT(14) },
> + [RST_BUS_TVE_TOP] = { 0x2c4, BIT(15) },
> + [RST_BUS_GMAC] = { 0x2c4, BIT(17) },
> + [RST_BUS_GPU] = { 0x2c4, BIT(20) },
> + [RST_BUS_TVD0] = { 0x2c4, BIT(21) },
> + [RST_BUS_TVD1] = { 0x2c4, BIT(22) },
> + [RST_BUS_TVD2] = { 0x2c4, BIT(23) },
> + [RST_BUS_TVD3] = { 0x2c4, BIT(24) },
> + [RST_BUS_TVD_TOP] = { 0x2c4, BIT(25) },
> + [RST_BUS_TCON0] = { 0x2c4, BIT(26) },
> + [RST_BUS_TCON1] = { 0x2c4, BIT(27) },
> + [RST_BUS_TCON_TVE0] = { 0x2c4, BIT(28) },
> + [RST_BUS_TCON_TVE1] = { 0x2c4, BIT(29) },
Same thing about the TCON names.
> + [RST_BUS_TCON_TOP] = { 0x2c4, BIT(30) },
> + [RST_BUS_DBG] = { 0x2c4, BIT(31) },
> +
> + [RST_BUS_LVDS] = { 0x2c8, BIT(0) },
> +
> + [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
> + [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
> + [RST_BUS_AC97] = { 0x2d0, BIT(2) },
> + [RST_BUS_IR0] = { 0x2d0, BIT(6) },
> + [RST_BUS_IR1] = { 0x2d0, BIT(7) },
> + [RST_BUS_THS] = { 0x2d0, BIT(8) },
> + [RST_BUS_KEYPAD] = { 0x2d0, BIT(10) },
> + [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
> + [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
> + [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
> +
> + [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
> + [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
> + [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
> + [RST_BUS_I2C3] = { 0x2d8, BIT(3) },
> + [RST_BUS_CAN] = { 0x2d8, BIT(4) },
Please add a note for CAN like you did with the bus gate.
> + [RST_BUS_SCR] = { 0x2d8, BIT(5) },
> + [RST_BUS_PS20] = { 0x2d8, BIT(6) },
> + [RST_BUS_PS21] = { 0x2d8, BIT(7) },
> + [RST_BUS_I2C4] = { 0x2d8, BIT(15) },
> + [RST_BUS_UART0] = { 0x2d8, BIT(16) },
> + [RST_BUS_UART1] = { 0x2d8, BIT(17) },
> + [RST_BUS_UART2] = { 0x2d8, BIT(18) },
> + [RST_BUS_UART3] = { 0x2d8, BIT(19) },
> + [RST_BUS_UART4] = { 0x2d8, BIT(20) },
> + [RST_BUS_UART5] = { 0x2d8, BIT(21) },
> + [RST_BUS_UART6] = { 0x2d8, BIT(22) },
> + [RST_BUS_UART7] = { 0x2d8, BIT(23) },
> +};
> +
> +static const struct sunxi_ccu_desc sun8i_r40_ccu_desc = {
> + .ccu_clks = sun8i_r40_ccu_clks,
> + .num_ccu_clks = ARRAY_SIZE(sun8i_r40_ccu_clks),
> +
> + .hw_clks = &sun8i_r40_hw_clks,
> +
> + .resets = sun8i_r40_ccu_resets,
> + .num_resets = ARRAY_SIZE(sun8i_r40_ccu_resets),
> +};
> +
> +static struct ccu_mux_nb sun8i_r40_cpu_nb = {
> + .common = &cpu_clk.common,
> + .cm = &cpu_clk.mux,
> + .delay_us = 1, /* > 8 clock cycles at 24 MHz */
> + .bypass_index = 1, /* index of 24 MHz oscillator */
> +};
> +
> +static void __init sun8i_r40_ccu_setup(struct device_node *node)
> +{
> + void __iomem *reg;
> + u32 val;
> +
> + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg)) {
> + pr_err("%s: Could not map the clock registers\n",
> + of_node_full_name(node));
> + return;
> + }
> +
> + /* Force the PLL-Audio-1x divider to 4 */
> + val = readl(reg + SUN8I_R40_PLL_AUDIO_REG);
> + val &= ~GENMASK(19, 16);
> + writel(val | (3 << 16), reg + SUN8I_R40_PLL_AUDIO_REG);
> +
> + sunxi_ccu_probe(node, reg, &sun8i_r40_ccu_desc);
> +
> + ccu_mux_notifier_register(pll_cpu_clk.common.hw.clk,
> + &sun8i_r40_cpu_nb);
> +}
> +CLK_OF_DECLARE(sun8i_r40_ccu, "allwinner,sun8i-r40-ccu",
> + sun8i_r40_ccu_setup);
> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.h b/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
> new file mode 100644
> index 000000000000..be30eb662d78
> --- /dev/null
> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
> @@ -0,0 +1,68 @@
> +/*
> + * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _CCU_SUN8I_R40_H_
> +#define _CCU_SUN8I_R40_H_
> +
> +#include <dt-bindings/clock/sun8i-r40-ccu.h>
> +#include <dt-bindings/reset/sun8i-r40-ccu.h>
> +
> +#define CLK_OSC24M_2X 0
As mentioned, please drop this one.
> +#define CLK_OSC24M_32K 1
> +#define CLK_PLL_CPU 2
> +#define CLK_PLL_AUDIO_BASE 3
> +#define CLK_PLL_AUDIO 4
> +#define CLK_PLL_AUDIO_2X 5
> +#define CLK_PLL_AUDIO_4X 6
> +#define CLK_PLL_AUDIO_8X 7
> +#define CLK_PLL_VIDEO0 8
> +#define CLK_PLL_VIDEO0_2X 9
> +#define CLK_PLL_VE 10
> +#define CLK_PLL_DDR0 11
> +#define CLK_PLL_PERIPH0 12
> +#define CLK_PLL_PERIPH0_2X 13
> +#define CLK_PLL_PERIPH1 14
> +#define CLK_PLL_PERIPH1_2X 15
> +#define CLK_PLL_VIDEO1 16
> +#define CLK_PLL_VIDEO1_2X 17
> +#define CLK_PLL_SATA 18
> +#define CLK_PLL_GPU 19
> +#define CLK_PLL_MIPI 20
> +#define CLK_PLL_DE 21
> +#define CLK_PLL_DDR1 22
> +
> +/* The CPU clock is exported */
> +
> +#define CLK_AXI 24
> +#define CLK_AHB1 25
> +#define CLK_APB1 26
> +#define CLK_APB2 27
> +
> +/* All the bus gates are exported */
> +
> +/* The first bunch of module clocks are exported */
> +
> +#define CLK_DRAM 134
> +
> +/* All the DRAM gates are exported */
> +
> +/* Some more module clocks are exported */
> +
> +#define CLK_MBUS 158
> +
> +/* Another bunch of module clocks are exported */
> +
> +#define CLK_NUMBER (CLK_OUTB + 1)
> +
> +#endif /* _CCU_SUN8I_R40_H_ */
> diff --git a/include/dt-bindings/clock/sun8i-r40-ccu.h b/include/dt-bindings/clock/sun8i-r40-ccu.h
> new file mode 100644
> index 000000000000..a907d841496d
> --- /dev/null
> +++ b/include/dt-bindings/clock/sun8i-r40-ccu.h
> @@ -0,0 +1,191 @@
> +/*
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#ifndef _DT_BINDINGS_CLK_SUN8I_R40_H_
> +#define _DT_BINDINGS_CLK_SUN8I_R40_H_
> +
> +#define CLK_CPU 23
> +
> +#define CLK_BUS_MIPI_DSI 28
> +#define CLK_BUS_CE 29
> +#define CLK_BUS_DMA 30
> +#define CLK_BUS_MMC0 31
> +#define CLK_BUS_MMC1 32
> +#define CLK_BUS_MMC2 33
> +#define CLK_BUS_MMC3 34
> +#define CLK_BUS_NAND 35
> +#define CLK_BUS_DRAM 36
> +#define CLK_BUS_EMAC 37
> +#define CLK_BUS_TS 38
> +#define CLK_BUS_HSTIMER 39
> +#define CLK_BUS_SPI0 40
> +#define CLK_BUS_SPI1 41
> +#define CLK_BUS_SPI2 42
> +#define CLK_BUS_SPI3 43
> +#define CLK_BUS_SATA 44
> +#define CLK_BUS_OTG 45
> +#define CLK_BUS_EHCI0 46
> +#define CLK_BUS_EHCI1 47
> +#define CLK_BUS_EHCI2 48
> +#define CLK_BUS_OHCI0 49
> +#define CLK_BUS_OHCI1 50
> +#define CLK_BUS_OHCI2 51
> +#define CLK_BUS_VE 52
> +#define CLK_BUS_DE_MP 53
MP name...
> +#define CLK_BUS_DEINTERLACE 54
> +#define CLK_BUS_CSI0 55
> +#define CLK_BUS_CSI1 56
> +#define CLK_BUS_HDMI_SLOW 57
> +#define CLK_BUS_HDMI 58
Names...
> +#define CLK_BUS_DE 59
> +#define CLK_BUS_TVE0 60
> +#define CLK_BUS_TVE1 61
> +#define CLK_BUS_TVE_TOP 62
> +#define CLK_BUS_GMAC 63
> +#define CLK_BUS_GPU 64
> +#define CLK_BUS_TVD0 65
> +#define CLK_BUS_TVD1 66
> +#define CLK_BUS_TVD2 67
> +#define CLK_BUS_TVD3 68
> +#define CLK_BUS_TVD_TOP 69
> +#define CLK_BUS_TCON0 70
> +#define CLK_BUS_TCON1 71
> +#define CLK_BUS_TVE0_TCON 72
> +#define CLK_BUS_TVE1_TCON 73
Names...
> +#define CLK_BUS_TCON_TOP 74
> +#define CLK_BUS_CODEC 75
> +#define CLK_BUS_SPDIF 76
> +#define CLK_BUS_AC97 77
> +#define CLK_BUS_PIO 78
> +#define CLK_BUS_IR0 79
> +#define CLK_BUS_IR1 80
> +#define CLK_BUS_THS 81
> +#define CLK_BUS_KEYPAD 82
> +#define CLK_BUS_I2S0 83
> +#define CLK_BUS_I2S1 84
> +#define CLK_BUS_I2S2 85
> +#define CLK_BUS_I2C0 86
> +#define CLK_BUS_I2C1 87
> +#define CLK_BUS_I2C2 88
> +#define CLK_BUS_I2C3 89
> +#define CLK_BUS_CAN 90
> +#define CLK_BUS_SCR 91
> +#define CLK_BUS_PS20 92
> +#define CLK_BUS_PS21 93
> +#define CLK_BUS_I2C4 94
> +#define CLK_BUS_UART0 95
> +#define CLK_BUS_UART1 96
> +#define CLK_BUS_UART2 97
> +#define CLK_BUS_UART3 98
> +#define CLK_BUS_UART4 99
> +#define CLK_BUS_UART5 100
> +#define CLK_BUS_UART6 101
> +#define CLK_BUS_UART7 102
> +#define CLK_BUS_DBG 103
> +
> +#define CLK_THS 104
> +#define CLK_NAND 105
> +#define CLK_MMC0 106
> +#define CLK_MMC1 107
> +#define CLK_MMC2 108
> +#define CLK_MMC3 109
> +#define CLK_TS 110
> +#define CLK_CE 111
> +#define CLK_SPI0 112
> +#define CLK_SPI1 113
> +#define CLK_SPI2 114
> +#define CLK_SPI3 115
> +#define CLK_I2S0 116
> +#define CLK_I2S1 117
> +#define CLK_I2S2 118
> +#define CLK_AC97 119
> +#define CLK_SPDIF 120
> +#define CLK_KEYPAD 121
> +#define CLK_SATA 122
> +#define CLK_USB_PHY0 123
> +#define CLK_USB_PHY1 124
> +#define CLK_USB_PHY2 125
> +#define CLK_USB_OHCI0 126
> +#define CLK_USB_OHCI1 127
> +#define CLK_USB_OHCI2 128
> +#define CLK_USB_OHCI0_12M 129
> +#define CLK_USB_OHCI1_12M 130
> +#define CLK_USB_OHCI2_12M 131
These 3 should not be exported.
> +#define CLK_IR0 132
> +#define CLK_IR1 133
> +
> +#define CLK_DRAM_VE 135
> +#define CLK_DRAM_CSI0 136
> +#define CLK_DRAM_CSI1 137
> +#define CLK_DRAM_TS 138
> +#define CLK_DRAM_TVD 139
> +#define CLK_DRAM_DE_MP 140
MP name...
> +#define CLK_DRAM_DEINTERLACE 141
> +#define CLK_DE 142
> +#define CLK_DE_MP 143
MP name...
> +#define CLK_TCON0 144
> +#define CLK_TCON1 145
> +#define CLK_TCON_TVE0 146
> +#define CLK_TCON_TVE1 147
Names...
> +#define CLK_DEINTERLACE 148
> +#define CLK_CSI1_MCLK 149
> +#define CLK_CSI_SCLK 150
> +#define CLK_CSI0_MCLK 151
> +#define CLK_VE 152
> +#define CLK_ADDA 153
> +#define CLK_ADDA_4X 154
Nonexistent.
> +#define CLK_AVS 155
> +#define CLK_HDMI 156
> +#define CLK_HDMI_SLOW 157
> +
> +#define CLK_MIPI_DSI 159
> +#define CLK_TVE0 160
> +#define CLK_TVE1 161
> +#define CLK_TVD0 162
> +#define CLK_TVD1 163
> +#define CLK_TVD2 164
> +#define CLK_TVD3 165
> +#define CLK_GPU 166
> +#define CLK_OUTA 167
> +#define CLK_OUTB 168
> +
> +#endif /* _DT_BINDINGS_CLK_SUN8I_R40_H_ */
> diff --git a/include/dt-bindings/reset/sun8i-r40-ccu.h b/include/dt-bindings/reset/sun8i-r40-ccu.h
> new file mode 100644
> index 000000000000..a7001f34b0b9
> --- /dev/null
> +++ b/include/dt-bindings/reset/sun8i-r40-ccu.h
Name corrections apply to this file as well.
Regards
ChenYu
> --
> 2.12.2
>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 09/10] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40
2017-05-27 10:23 ` [PATCH v3 09/10] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40 Icenowy Zheng
@ 2017-05-29 8:15 ` Chen-Yu Tsai
0 siblings, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-29 8:15 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
Hi,
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> From: Chen-Yu Tsai <wens@csie.org>
>
> The Allwinner R40 SoC is marketed as the successor to the A20 SoC.
> The R40 is a smaller chip than the A20, but features the same set
> of programmable pins, with a couple extra pins and some new pin
> functions. The chip features 4 Cortex-A7 cores and a Mali-400 MP2
> GPU. It retains most if not all features from the A20, while adding
> some new features, such as MIPI DSI output, or updating various
> hardware blocks, such as DE 2.0.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Pinmux changes.
>
> arch/arm/boot/dts/sun8i-r40.dtsi | 408 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 408 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-r40.dtsi
>
> diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
> new file mode 100644
> index 000000000000..1d36485c6ef7
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-r40.dtsi
> @@ -0,0 +1,408 @@
> +/*
> + * Copyright 2017 Chen-Yu Tsai <wens@csie.org>
> + * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/sun8i-r40-ccu.h>
> +#include <dt-bindings/reset/sun8i-r40-ccu.h>
> +
> +/ {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupt-parent = <&gic>;
> +
> + aliases {
> + };
> +
> + chosen {
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + osc24M: osc24M {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
Please add the accuracy of the oscillator. Allwinner requires it
to be within +/- 50 ppm for this one.
> + };
> +
> + osc32k: osc32k {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
And +/- 20 ppm for this one.
> + clock-output-names = "osc32k";
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu@0 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <0>;
> + };
> +
> + cpu@1 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <1>;
> + };
> +
> + cpu@2 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <2>;
> + };
> +
> + cpu@3 {
> + compatible = "arm,cortex-a7";
> + device_type = "cpu";
> + reg = <3>;
> + };
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x40000000 0x80000000>;
> + };
> +
> + soc@1c00000 {
Please drop the @1c00000 part to avoid introducing new warnings.
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + nmi_intc: interrupt-controller@1c00030 {
> + compatible = "allwinner,sun7i-a20-sc-nmi";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + reg = <0x01c00030 0x0c>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + mmc0: mmc@1c0f000 {
> + compatible = "allwinner,sun50i-a64-mmc";
Please add a new R40 specific compatible in front, in case we run into any
SoC specific issues.
> + reg = <0x01c0f000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
As a rule of thumb, if you are targeting the same release for merging
both the clock driver and any clock users in the device tree, please split
the device tree into two patches, the first using raw numbers, and the
second converting the raw numbers into macros from the device tree binding
headers. This makes it easier for the platform maintainers.
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC0>;
> + reset-names = "ahb";
> + pinctrl-0 = <&mmc0_pins>;
> + pinctrl-names = "default";
> + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <150000000>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc1: mmc@1c10000 {
> + compatible = "allwinner,sun50i-a64-mmc";
> + reg = <0x01c10000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC1>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <150000000>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc2: mmc@1c11000 {
> + compatible = "allwinner,sun50i-a64-emmc";
> + reg = <0x01c11000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC2>;
> + reset-names = "ahb";
> + pinctrl-0 = <&mmc2_pins>;
> + pinctrl-names = "default";
> + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <200000000>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc3: mmc@1c12000 {
> + compatible = "allwinner,sun50i-a64-mmc";
> + reg = <0x01c12000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC3>, <&ccu CLK_MMC3>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC3>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <150000000>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + ccu: clock@1c20000 {
> + compatible = "allwinner,sun8i-r40-ccu";
> + reg = <0x01c20000 0x400>;
> + clocks = <&osc24M>, <&osc32k>;
> + clock-names = "hosc", "losc";
As mentioned previously by Maxime, the losc clock comes from the RTC
module where it is muxed. The mux is depicted in the clock tree section
of the user manual. Please add the RTC and the internal oscillator.
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + pio: pinctrl@1c20800 {
> + compatible = "allwinner,sun8i-r40-pinctrl";
> + reg = <0x01c20800 0x400>;
> + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
> + clock-names = "apb", "hosc", "losc";
> + gpio-controller;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + #gpio-cells = <3>;
> +
> + i2c0_pins: i2c0-pins {
> + pins = "PB0", "PB1";
> + function = "i2c0";
> + };
> +
> + mmc0_pins: mmc0-pins {
> + pins = "PF0", "PF1", "PF2",
> + "PF3", "PF4", "PF5";
> + function = "mmc0";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + mmc1_pg_pins: mmc1-pg-pins {
Cool!
> + pins = "PG0", "PG1", "PG2",
> + "PG3", "PG4", "PG5";
> + function = "mmc1";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + mmc2_pins: mmc2-pins {
Please name this mmc2-emmc-pins, in case someone does a 2-SD-card variant.
> + pins = "PC5", "PC6", "PC7", "PC8", "PC9",
> + "PC10", "PC11", "PC12", "PC13", "PC14",
> + "PC15", "PC24";
> + function = "mmc2";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + uart0_pb_pins: uart0-pb-pins {
> + pins = "PB22", "PB23";
> + function = "uart0";
> + };
> + };
> +
> + uart0: serial@1c28000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28000 0x400>;
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART0>;
> + resets = <&ccu RST_BUS_UART0>;
> + status = "disabled";
> + };
> +
> + uart1: serial@1c28400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28400 0x400>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART1>;
> + resets = <&ccu RST_BUS_UART1>;
> + status = "disabled";
> + };
> +
> + uart2: serial@1c28800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28800 0x400>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART2>;
> + resets = <&ccu RST_BUS_UART2>;
> + status = "disabled";
> + };
> +
> + uart3: serial@1c28c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c28c00 0x400>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART3>;
> + resets = <&ccu RST_BUS_UART3>;
> + status = "disabled";
> + };
> +
> + uart4: serial@1c29000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c29000 0x400>;
> + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART4>;
> + resets = <&ccu RST_BUS_UART4>;
> + status = "disabled";
> + };
> +
> + uart5: serial@1c29400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c29400 0x400>;
> + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART5>;
> + resets = <&ccu RST_BUS_UART5>;
> + status = "disabled";
> + };
> +
> + uart6: serial@1c29800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c29800 0x400>;
> + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART6>;
> + resets = <&ccu RST_BUS_UART6>;
> + status = "disabled";
> + };
> +
> + uart7: serial@1c29c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x01c29c00 0x400>;
> + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART7>;
> + resets = <&ccu RST_BUS_UART7>;
> + status = "disabled";
> + };
> +
> + i2c0: i2c@1c2ac00 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2ac00 0x400>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C0>;
> + resets = <&ccu RST_BUS_I2C0>;
> + pinctrl-0 = <&i2c0_pins>;
> + pinctrl-names = "default";
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c1: i2c@1c2b000 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b000 0x400>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C1>;
> + resets = <&ccu RST_BUS_I2C1>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c2: i2c@1c2b400 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b400 0x400>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C2>;
> + resets = <&ccu RST_BUS_I2C2>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c3: i2c@1c2b800 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2b800 0x400>;
> + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C3>;
> + resets = <&ccu RST_BUS_I2C3>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c4: i2c@1c2c000 {
> + compatible = "allwinner,sun6i-a31-i2c";
> + reg = <0x01c2c000 0x400>;
> + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C4>;
> + resets = <&ccu RST_BUS_I2C4>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + gic: interrupt-controller@1c81000 {
> + compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
Please use "arm,gic-400" instead.
Regards
ChenYu
> + reg = <0x01c81000 0x1000>,
> + <0x01c82000 0x1000>,
> + <0x01c84000 0x2000>,
> + <0x01c86000 0x2000>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv7-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> + clock-frequency = <24000000>;
> + arm,cpu-registers-not-fw-configured;
> + };
> +};
> --
> 2.12.2
>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 10/10] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra
2017-05-27 10:23 ` [PATCH v3 10/10] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra Icenowy Zheng
@ 2017-05-29 8:59 ` Chen-Yu Tsai
0 siblings, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-29 8:59 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> From: Chen-Yu Tsai <wens@csie.org>
>
> The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
> form factor and position of various connectors, leds and buttons is
> similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
> as the latest Banana Pi M64.
>
> It features:
>
> - X-Powers AXP221s PMIC connected to i2c0
> - 2 GB DDR3 DRAM
> - 8 GB eMMC
> - micro SD card slot
> - DC power jack
> - HDMI output
> - MIPI DSI connector
> - 2x USB 2.0 hosts
> - 1x USB 2.0 OTG
> - gigabit ethernet with Realtek RTL8211E transceiver
> - WiFi/Bluetooth with AP6212 chip, with external antenna connector
> - SATA and power connectors for native SATA support
> - camera sensor connector
> - consumer IR receiver
> - audio out headphone jack
> - onboard microphone
> - red, green, and blue LEDs
> - debug UART pins
> - Li-Po battery connector
> - Raspberry Pi B+ compatible GPIO header
> - power, reset, and boot control buttons
>
> This patch adds a dts file that enables debug UART and MMC support.
>
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Pinmux changes.
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 157 ++++++++++++++++++++++
> 2 files changed, 158 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index f68d6e0bc746..697c600bba28 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -910,6 +910,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> sun8i-h3-orangepi-plus.dtb \
> sun8i-h3-orangepi-plus2e.dtb \
> sun8i-r16-parrot.dtb \
> + sun8i-r40-bananapi-m2-ultra.dtb \
> sun8i-v3s-licheepi-zero.dtb \
> sun8i-v3s-licheepi-zero-dock.dtb
> dtb-$(CONFIG_MACH_SUN9I) += \
> diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
> new file mode 100644
> index 000000000000..c4e69847cea1
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
> @@ -0,0 +1,157 @@
> +/*
> + * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-r40.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +/ {
> + model = "Banana Pi BPI-M2-Ultra";
> + compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40";
The vendor prefix "bananapi" was merged into -next through Rob's DT tree:
https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=79d45aed23f02022607501cd0d3c404592e027f8
Lets use that instead.
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + wifi_pwrseq: wifi_pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + axp22x: pmic@68 {
Address here does not match the reg property below.
> + compatible = "x-powers,axp221";
> + reg = <0x34>;
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +#include "axp22x.dtsi"
> +
> +®_aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "avcc";
> +};
> +
> +®_dcdc1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "vcc-3v0";
Board schematic says 3.3V.
> +};
> +
> +®_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +®_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-name = "vdd-sys";
> +};
> +
> +®_dcdc5 {
> + regulator-always-on;
> + regulator-min-microvolt = <1500000>;
> + regulator-max-microvolt = <1500000>;
There is a small tolerance range: 1.425V ~ 1.575V.
> + regulator-name = "vcc-dram";
> +};
> +
> +®_dldo1 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
Recommended range on the AP6212 is 1.7V ~ 3.6V.
> + regulator-name = "vcc-wifi-io";
> +};
> +
> +®_dldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
Recommended range on the AP6212 is 3.0V ~ 4.8V.
Regards
ChenYu
> + regulator-name = "vcc-wifi";
> +};
> +
> +&mmc0 {
> + vmmc-supply = <®_dcdc1>;
> + bus-width = <4>;
> + cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pg_pins>;
> + vmmc-supply = <®_dldo2>;
> + vqmmc-supply = <®_dldo1>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&mmc2 {
> + vmmc-supply = <®_dcdc1>;
> + vqmmc-supply = <®_dcdc1>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pb_pins>;
> + status = "okay";
> +};
> --
> 2.12.2
>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver
2017-05-27 10:23 ` [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver Icenowy Zheng
@ 2017-05-29 13:11 ` Chen-Yu Tsai
2017-05-29 13:19 ` icenowy
2017-05-29 16:43 ` Linus Walleij
1 sibling, 1 reply; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-29 13:11 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Maxime Ripard, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 06:23:04PM +0800, Icenowy Zheng wrote:
> R40 is said to be an upgrade of A20, and its pin configuration is also
> similar to A20 (and thus similar to A10).
>
> Add support for R40 to the A10 pinctrl driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> drivers/pinctrl/sunxi/Kconfig | 2 +-
> drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 272 +++++++++++++++++++++---------
> 2 files changed, 197 insertions(+), 77 deletions(-)
>
> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
> index 624d84e6c936..9d01da3b90bd 100644
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
> @@ -7,7 +7,7 @@ config PINCTRL_SUNXI
> select GPIOLIB
>
> config PINCTRL_SUN4I_A10
> - def_bool MACH_SUN4I || MACH_SUN7I
> + def_bool MACH_SUN4I || MACH_SUN7I || MACH_SUN8I
> select PINCTRL_SUNXI
>
> config PINCTRL_SUN5I
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
> index 159580c04b14..0f6ca8391ea7 100644
> --- a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
[...]
> @@ -162,14 +183,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
> SUNXI_FUNCTION(0x3, "can"), /* RX */
> SUNXI_FUNCTION(0x4, "uart1"), /* RING */
> SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXERR */
> - PINCTRL_SUN7I_A20),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40),
> SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DI */
> - PINCTRL_SUN7I_A20)),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40)),
> /* Hole */
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> - SUNXI_FUNCTION(0x2, "i2c0")), /* SCK */
> + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
> + SUNXI_FUNCTION_VARIANT(0x3,
> + "pll-lock-dbg",
Can you stick to underscores to be consistent?
> + PINCTRL_SUN8I_R40)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> @@ -177,11 +203,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> - SUNXI_FUNCTION(0x2, "pwm")), /* PWM0 */
> + SUNXI_FUNCTION_VARIANT(0x2, "pwm", /* PWM0 */
> + PINCTRL_SUN4I_A10 |
> + PINCTRL_SUN7I_A20),
> + SUNXI_FUNCTION_VARIANT(0x3, "pwm", /* PWM0 */
> + PINCTRL_SUN8I_R40)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> - SUNXI_FUNCTION(0x2, "ir0"), /* TX */
> + SUNXI_FUNCTION_VARIANT(0x2, "ir0", /* TX */
> + PINCTRL_SUN4I_A10 |
> + PINCTRL_SUN7I_A20),
> + SUNXI_FUNCTION_VARIANT(0x3, "pwm0", /* PWM1 */
The numbering is wrong. Just drop the number altogether, like all the
other instances.
> + PINCTRL_SUN8I_R40),
> /*
> * The SPDIF block is not referenced at all in the A10 user
> * manual. However it is described in the code leaked and the
> @@ -205,7 +239,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* MCLK */
> PINCTRL_SUN4I_A10),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* MCLK */
> - PINCTRL_SUN7I_A20),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40),
Maybe we could use "i2s" instead, like on the A10. I don't know where
i2s1 is used, but it certainly isn't routed outside the SoC, and i2s2
looks like it's for dw-hdmi's audio path.
> SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
> SUNXI_FUNCTION(0x0, "gpio_in"),
[...]
> @@ -237,31 +275,41 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO1 */
> PINCTRL_SUN4I_A10),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO1 */
> - PINCTRL_SUN7I_A20)),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40),
> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM6 */
> + PINCTRL_SUN8I_R40)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO2 */
> PINCTRL_SUN4I_A10),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO2 */
> - PINCTRL_SUN7I_A20)),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40),
> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM7 */
> + PINCTRL_SUN8I_R40)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO3 */
> PINCTRL_SUN4I_A10),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO3 */
> - PINCTRL_SUN7I_A20)),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DI */
> PINCTRL_SUN4I_A10),
> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DI */
> - PINCTRL_SUN7I_A20),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40),
> SUNXI_FUNCTION(0x3, "ac97"), /* DI */
> /* Undocumented mux function on A10 - See SPDIF MCLK above */
> - SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF IN */
> + SUNXI_FUNCTION_VARIANT(0x4, "spdif", /* SPDIF IN */
> + PINCTRL_SUN4I_A10 |
> + PINCTRL_SUN7I_A20)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> @@ -308,7 +356,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
You missed PWM4 and PWM5 on pins PB20 and PB21.
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
> SUNXI_FUNCTION(0x2, "uart0"), /* TX */
> - SUNXI_FUNCTION(0x3, "ir1")), /* TX */
> + SUNXI_FUNCTION_VARIANT(0x3, "ir1", /* TX */
> + PINCTRL_SUN4I_A10 |
> + PINCTRL_SUN7I_A20)),
> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 23),
> SUNXI_FUNCTION(0x0, "gpio_in"),
> SUNXI_FUNCTION(0x1, "gpio_out"),
[...]
> @@ -916,7 +1000,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] = {
> SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD12 */
> PINCTRL_SUN4I_A10),
> SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD1 */
> - PINCTRL_SUN7I_A20),
> + PINCTRL_SUN7I_A20 |
> + PINCTRL_SUN8I_R40),
> + SUNXI_FUNCTION_VARIANT(0x5, "sim", /* DET */
> + PINCTRL_SUN8I_R40),
This is available on all 3 variants.
Should we consider sending a fix for this first? The hardware backing
this pin is not supported, but it would be less confusing to fix it
first instead of introducing a function for all variants in a patch
supposedly for just the R40.
> SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
> SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
> SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
[...]
Looks good otherwise.
Regards
ChenYu
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver
2017-05-29 13:11 ` Chen-Yu Tsai
@ 2017-05-29 13:19 ` icenowy
2017-05-29 13:25 ` Chen-Yu Tsai
0 siblings, 1 reply; 36+ messages in thread
From: icenowy @ 2017-05-29 13:19 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: devicetree, linux-doc, Linus Walleij, linux-kernel, linux-gpio,
Rob Herring, Maxime Ripard, linux-clk, linux-arm-kernel
在 2017-05-29 21:11，Chen-Yu Tsai 写道：
> On Sat, May 27, 2017 at 06:23:04PM +0800, Icenowy Zheng wrote:
>> R40 is said to be an upgrade of A20, and its pin configuration is also
>> similar to A20 (and thus similar to A10).
>>
>> Add support for R40 to the A10 pinctrl driver.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> ---
>> drivers/pinctrl/sunxi/Kconfig | 2 +-
>> drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 272
>> +++++++++++++++++++++---------
>> 2 files changed, 197 insertions(+), 77 deletions(-)
>>
>> diff --git a/drivers/pinctrl/sunxi/Kconfig
>> b/drivers/pinctrl/sunxi/Kconfig
>> index 624d84e6c936..9d01da3b90bd 100644
>> --- a/drivers/pinctrl/sunxi/Kconfig
>> +++ b/drivers/pinctrl/sunxi/Kconfig
>> @@ -7,7 +7,7 @@ config PINCTRL_SUNXI
>> select GPIOLIB
>>
>> config PINCTRL_SUN4I_A10
>> - def_bool MACH_SUN4I || MACH_SUN7I
>> + def_bool MACH_SUN4I || MACH_SUN7I || MACH_SUN8I
>> select PINCTRL_SUNXI
>>
>> config PINCTRL_SUN5I
>> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>> b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>> index 159580c04b14..0f6ca8391ea7 100644
>> --- a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>
> [...]
>
>> @@ -162,14 +183,19 @@ static const struct sunxi_desc_pin
>> sun4i_a10_pins[] = {
>> SUNXI_FUNCTION(0x3, "can"), /* RX */
>> SUNXI_FUNCTION(0x4, "uart1"), /* RING */
>> SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXERR */
>> - PINCTRL_SUN7I_A20),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40),
>> SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DI */
>> - PINCTRL_SUN7I_A20)),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40)),
>> /* Hole */
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> - SUNXI_FUNCTION(0x2, "i2c0")), /* SCK */
>> + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
>> + SUNXI_FUNCTION_VARIANT(0x3,
>> + "pll-lock-dbg",
>
> Can you stick to underscores to be consistent?
OK...
This is a so strange pin name and I just picked the datasheet
name.
I don't care how to name it as I don't even know what this is.
>
>> + PINCTRL_SUN8I_R40)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> @@ -177,11 +203,19 @@ static const struct sunxi_desc_pin
>> sun4i_a10_pins[] = {
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> - SUNXI_FUNCTION(0x2, "pwm")), /* PWM0 */
>> + SUNXI_FUNCTION_VARIANT(0x2, "pwm", /* PWM0 */
>> + PINCTRL_SUN4I_A10 |
>> + PINCTRL_SUN7I_A20),
>> + SUNXI_FUNCTION_VARIANT(0x3, "pwm", /* PWM0 */
>> + PINCTRL_SUN8I_R40)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> - SUNXI_FUNCTION(0x2, "ir0"), /* TX */
>> + SUNXI_FUNCTION_VARIANT(0x2, "ir0", /* TX */
>> + PINCTRL_SUN4I_A10 |
>> + PINCTRL_SUN7I_A20),
>> + SUNXI_FUNCTION_VARIANT(0x3, "pwm0", /* PWM1 */
>
> The numbering is wrong. Just drop the number altogether, like all the
> other instances.
>
>> + PINCTRL_SUN8I_R40),
>> /*
>> * The SPDIF block is not referenced at all in the A10 user
>> * manual. However it is described in the code leaked and the
>> @@ -205,7 +239,8 @@ static const struct sunxi_desc_pin
>> sun4i_a10_pins[] = {
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* MCLK */
>> PINCTRL_SUN4I_A10),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* MCLK */
>> - PINCTRL_SUN7I_A20),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40),
>
> Maybe we could use "i2s" instead, like on the A10. I don't know where
> i2s1 is used, but it certainly isn't routed outside the SoC, and i2s2
> looks like it's for dw-hdmi's audio path.
Nope, it's routed at PA bank, see pins start at PA14.
Changing this name will also break existing A20 device trees, if any of
them use I2S.
>
>> SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>
> [...]
>
>> @@ -237,31 +275,41 @@ static const struct sunxi_desc_pin
>> sun4i_a10_pins[] = {
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO1 */
>> PINCTRL_SUN4I_A10),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO1 */
>> - PINCTRL_SUN7I_A20)),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40),
>> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM6 */
>> + PINCTRL_SUN8I_R40)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO2 */
>> PINCTRL_SUN4I_A10),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO2 */
>> - PINCTRL_SUN7I_A20)),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40),
>> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM7 */
>> + PINCTRL_SUN8I_R40)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO3 */
>> PINCTRL_SUN4I_A10),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO3 */
>> - PINCTRL_SUN7I_A20)),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DI */
>> PINCTRL_SUN4I_A10),
>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DI */
>> - PINCTRL_SUN7I_A20),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40),
>> SUNXI_FUNCTION(0x3, "ac97"), /* DI */
>> /* Undocumented mux function on A10 - See SPDIF MCLK above */
>> - SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF IN */
>> + SUNXI_FUNCTION_VARIANT(0x4, "spdif", /* SPDIF IN */
>> + PINCTRL_SUN4I_A10 |
>> + PINCTRL_SUN7I_A20)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> @@ -308,7 +356,9 @@ static const struct sunxi_desc_pin
>> sun4i_a10_pins[] = {
>
> You missed PWM4 and PWM5 on pins PB20 and PB21.
>
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>> SUNXI_FUNCTION(0x2, "uart0"), /* TX */
>> - SUNXI_FUNCTION(0x3, "ir1")), /* TX */
>> + SUNXI_FUNCTION_VARIANT(0x3, "ir1", /* TX */
>> + PINCTRL_SUN4I_A10 |
>> + PINCTRL_SUN7I_A20)),
>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 23),
>> SUNXI_FUNCTION(0x0, "gpio_in"),
>> SUNXI_FUNCTION(0x1, "gpio_out"),
>
> [...]
>
>> @@ -916,7 +1000,10 @@ static const struct sunxi_desc_pin
>> sun4i_a10_pins[] = {
>> SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD12 */
>> PINCTRL_SUN4I_A10),
>> SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD1 */
>> - PINCTRL_SUN7I_A20),
>> + PINCTRL_SUN7I_A20 |
>> + PINCTRL_SUN8I_R40),
>> + SUNXI_FUNCTION_VARIANT(0x5, "sim", /* DET */
>> + PINCTRL_SUN8I_R40),
>
> This is available on all 3 variants.
>
> Should we consider sending a fix for this first? The hardware backing
> this pin is not supported, but it would be less confusing to fix it
> first instead of introducing a function for all variants in a patch
> supposedly for just the R40.
OK.
But if we do so I think I should delay this patch until the A10-A20
driver merge is applied...
>
>> SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
>> SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
>> SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
>
> [...]
>
> Looks good otherwise.
>
>
> Regards
> ChenYu
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver
2017-05-29 13:19 ` icenowy
@ 2017-05-29 13:25 ` Chen-Yu Tsai
0 siblings, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-05-29 13:25 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, devicetree, linux-doc, Linus Walleij, linux-kernel,
linux-gpio, Rob Herring, Maxime Ripard, linux-clk,
linux-arm-kernel
On Mon, May 29, 2017 at 9:19 PM, <icenowy@aosc.io> wrote:
> 在 2017-05-29 21:11，Chen-Yu Tsai 写道：
>>
>> On Sat, May 27, 2017 at 06:23:04PM +0800, Icenowy Zheng wrote:
>>>
>>> R40 is said to be an upgrade of A20, and its pin configuration is also
>>> similar to A20 (and thus similar to A10).
>>>
>>> Add support for R40 to the A10 pinctrl driver.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>>> ---
>>> drivers/pinctrl/sunxi/Kconfig | 2 +-
>>> drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c | 272
>>> +++++++++++++++++++++---------
>>> 2 files changed, 197 insertions(+), 77 deletions(-)
>>>
>>> diff --git a/drivers/pinctrl/sunxi/Kconfig
>>> b/drivers/pinctrl/sunxi/Kconfig
>>> index 624d84e6c936..9d01da3b90bd 100644
>>> --- a/drivers/pinctrl/sunxi/Kconfig
>>> +++ b/drivers/pinctrl/sunxi/Kconfig
>>> @@ -7,7 +7,7 @@ config PINCTRL_SUNXI
>>> select GPIOLIB
>>>
>>> config PINCTRL_SUN4I_A10
>>> - def_bool MACH_SUN4I || MACH_SUN7I
>>> + def_bool MACH_SUN4I || MACH_SUN7I || MACH_SUN8I
>>> select PINCTRL_SUNXI
>>>
>>> config PINCTRL_SUN5I
>>> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>> b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>> index 159580c04b14..0f6ca8391ea7 100644
>>> --- a/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>> +++ b/drivers/pinctrl/sunxi/pinctrl-sun4i-a10.c
>>
>>
>> [...]
>>
>>> @@ -162,14 +183,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_FUNCTION(0x3, "can"), /* RX */
>>> SUNXI_FUNCTION(0x4, "uart1"), /* RING */
>>> SUNXI_FUNCTION_VARIANT(0x5, "gmac", /* GNULL / ETXERR
>>> */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> SUNXI_FUNCTION_VARIANT(0x6, "i2s1", /* DI */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40)),
>>> /* Hole */
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> - SUNXI_FUNCTION(0x2, "i2c0")), /* SCK */
>>> + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
>>> + SUNXI_FUNCTION_VARIANT(0x3,
>>> + "pll-lock-dbg",
>>
>>
>> Can you stick to underscores to be consistent?
>
>
> OK...
> This is a so strange pin name and I just picked the datasheet
> name.
>
> I don't care how to name it as I don't even know what this is.
>
>
>>
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> @@ -177,11 +203,19 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> - SUNXI_FUNCTION(0x2, "pwm")), /* PWM0 */
>>> + SUNXI_FUNCTION_VARIANT(0x2, "pwm", /* PWM0 */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20),
>>> + SUNXI_FUNCTION_VARIANT(0x3, "pwm", /* PWM0 */
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> - SUNXI_FUNCTION(0x2, "ir0"), /* TX */
>>> + SUNXI_FUNCTION_VARIANT(0x2, "ir0", /* TX */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20),
>>> + SUNXI_FUNCTION_VARIANT(0x3, "pwm0", /* PWM1 */
>>
>>
>> The numbering is wrong. Just drop the number altogether, like all the
>> other instances.
>>
>>> + PINCTRL_SUN8I_R40),
>>> /*
>>> * The SPDIF block is not referenced at all in the A10
>>> user
>>> * manual. However it is described in the code leaked and
>>> the
>>> @@ -205,7 +239,8 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] =
>>> {
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* MCLK */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* MCLK */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>
>>
>> Maybe we could use "i2s" instead, like on the A10. I don't know where
>> i2s1 is used, but it certainly isn't routed outside the SoC, and i2s2
>> looks like it's for dw-hdmi's audio path.
>
>
> Nope, it's routed at PA bank, see pins start at PA14.
>
> Changing this name will also break existing A20 device trees, if any of
> them use I2S.
Missed that one. Sorry about the noise.
>
>
>>
>>> SUNXI_FUNCTION(0x3, "ac97")), /* MCLK */
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>
>>
>> [...]
>>
>>> @@ -237,31 +275,41 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO1 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO1 */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM6 */
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 10),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO2 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO2 */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> + SUNXI_FUNCTION_VARIANT(0x4, "pwm", /* PWM7 */
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 11),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DO3 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DO3 */
>>> - PINCTRL_SUN7I_A20)),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 12),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s", /* DI */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x2, "i2s0", /* DI */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> SUNXI_FUNCTION(0x3, "ac97"), /* DI */
>>> /* Undocumented mux function on A10 - See SPDIF MCLK
>>> above */
>>> - SUNXI_FUNCTION(0x4, "spdif")), /* SPDIF IN */
>>> + SUNXI_FUNCTION_VARIANT(0x4, "spdif", /* SPDIF IN */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 13),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> @@ -308,7 +356,9 @@ static const struct sunxi_desc_pin sun4i_a10_pins[] =
>>> {
>>
>>
>> You missed PWM4 and PWM5 on pins PB20 and PB21.
>>
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>> SUNXI_FUNCTION(0x2, "uart0"), /* TX */
>>> - SUNXI_FUNCTION(0x3, "ir1")), /* TX */
>>> + SUNXI_FUNCTION_VARIANT(0x3, "ir1", /* TX */
>>> + PINCTRL_SUN4I_A10 |
>>> + PINCTRL_SUN7I_A20)),
>>> SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 23),
>>> SUNXI_FUNCTION(0x0, "gpio_in"),
>>> SUNXI_FUNCTION(0x1, "gpio_out"),
>>
>>
>> [...]
>>
>>> @@ -916,7 +1000,10 @@ static const struct sunxi_desc_pin sun4i_a10_pins[]
>>> = {
>>> SUNXI_FUNCTION_VARIANT(0x3, "pata", /* ATAD12 */
>>> PINCTRL_SUN4I_A10),
>>> SUNXI_FUNCTION_VARIANT(0x3, "emac", /* ETXD1 */
>>> - PINCTRL_SUN7I_A20),
>>> + PINCTRL_SUN7I_A20 |
>>> + PINCTRL_SUN8I_R40),
>>> + SUNXI_FUNCTION_VARIANT(0x5, "sim", /* DET */
>>> + PINCTRL_SUN8I_R40),
>>
>>
>> This is available on all 3 variants.
>>
>> Should we consider sending a fix for this first? The hardware backing
>> this pin is not supported, but it would be less confusing to fix it
>> first instead of introducing a function for all variants in a patch
>> supposedly for just the R40.
>
>
> OK.
>
> But if we do so I think I should delay this patch until the A10-A20
> driver merge is applied...
Since the hardware is unsupported to begin with, I think that's OK.
You could add an extra patch just before this one in the series.
ChenYu
>
>>
>>> SUNXI_FUNCTION(0x4, "keypad"), /* IN6 */
>>> SUNXI_FUNCTION_IRQ(0x6, 16), /* EINT16 */
>>> SUNXI_FUNCTION(0x7, "csi1")), /* D16 */
>>
>>
>> [...]
>>
>> Looks good otherwise.
>>
>>
>> Regards
>> ChenYu
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs
2017-05-27 10:23 ` [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs Icenowy Zheng
2017-05-28 14:58 ` Chen-Yu Tsai
@ 2017-05-29 16:33 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Linus Walleij @ 2017-05-29 16:33 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 12:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Allwinner A10, A20 and R40 SoCs have similar GPIO layout.
>
> Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support
> into A10 driver, and add R40 support into it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Commit message change.
Patch applied with Chen-Yu's review tag.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver
2017-05-27 10:23 ` [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver Icenowy Zheng
2017-05-28 15:06 ` Chen-Yu Tsai
@ 2017-05-29 16:35 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Linus Walleij @ 2017-05-29 16:35 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 12:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> As A20 is designed as a pin-compatible upgrade of A10, their pin
> controller are very similar, and can share one driver.
>
> Add A20 support to the A10 driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Enable A10 driver for A20 and disable A20 driver in this commit, in
> order to prevent A10 driver from conflicting with A20 driver.
Patch applied with Chen-Yu's review tag.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver
2017-05-27 10:23 ` [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver Icenowy Zheng
2017-05-28 15:08 ` Chen-Yu Tsai
@ 2017-05-29 16:39 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Linus Walleij @ 2017-05-29 16:39 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 12:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> As we added A20 support to A10 pinctrl driver, now we can delete the
> dedicated A20 pinctrl driver, which is duplicated code.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Only remove the A20 driver(A10 driver for A20 is enabled in
> the previous commit now).
Patch applied with Chen-Yu's review tag, and I also fixed
up the Makefile by removing the rule for this file.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl
2017-05-27 10:23 ` [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl Icenowy Zheng
2017-05-28 15:09 ` Chen-Yu Tsai
@ 2017-05-29 16:40 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Linus Walleij @ 2017-05-29 16:40 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 12:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> Allwinner R40 has a pin controller like the ones in older Allwinner SoCs
> (especially A20), and can use modified version of the A10/A20 pinctrl
> driver.
>
> Add a compatible string for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
> Changes in v3:
> - Added Rob's ACK.
Patch applied with Chen-Yu's review tag.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver
2017-05-27 10:23 ` [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver Icenowy Zheng
2017-05-29 13:11 ` Chen-Yu Tsai
@ 2017-05-29 16:43 ` Linus Walleij
1 sibling, 0 replies; 36+ messages in thread
From: Linus Walleij @ 2017-05-29 16:43 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 12:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
> R40 is said to be an upgrade of A20, and its pin configuration is also
> similar to A20 (and thus similar to A10).
>
> Add support for R40 to the A10 pinctrl driver.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Since I applied patches 2-5 you only need to resend from this point
for pin control.
Please send pin control patches separately from the rest of the series if you
can, and rebase on my "devel" branch, so I don't have to sift throgh so much
patches to find what I need to apply and what I can ignore.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 01/10] arm: sunxi: add support for R40 SoC
2017-05-27 10:22 ` [PATCH v3 01/10] arm: sunxi: add support for R40 SoC Icenowy Zheng
2017-05-28 14:57 ` Chen-Yu Tsai
@ 2017-05-31 19:42 ` Rob Herring
1 sibling, 0 replies; 36+ messages in thread
From: Rob Herring @ 2017-05-31 19:42 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Maxime Ripard, Chen-Yu Tsai, Linus Walleij, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, May 27, 2017 at 06:22:59PM +0800, Icenowy Zheng wrote:
> Allwinner R40 is a new SoC, with Quad Core Cortex-A7 and peripherals
> like A20.
>
> Add support for it.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v3:
> - Use V1.0 documents.
>
> Documentation/arm/sunxi/README | 6 ++++++
> Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
> arch/arm/mach-sunxi/sunxi.c | 1 +
> 3 files changed, 8 insertions(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-05-29 7:34 ` Chen-Yu Tsai
@ 2017-07-22 3:00 ` icenowy
2017-08-12 4:04 ` Chen-Yu Tsai
2017-08-12 4:04 ` icenowy
1 sibling, 1 reply; 36+ messages in thread
From: icenowy @ 2017-07-22 3:00 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: devicetree, linux-doc, Linus Walleij, linux-kernel, linux-gpio,
Rob Herring, Maxime Ripard, linux-clk, linux-arm-kernel
在 2017-05-29 15:34，Chen-Yu Tsai 写道：
> Hi,
>
> On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
>> Allwinner R40 SoC have a clock controller module in the style of the
>> SoCs beyond sun6i, however, it's more rich and complex.
>>
>> Add support for it.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> ---
>> Changes in v3:
>> - Rebased on current linux-next.
>> Changes in v2:
>> - Fixes according to the SoC's user manual.
>>
>> drivers/clk/sunxi-ng/Kconfig | 10 +
>> drivers/clk/sunxi-ng/Makefile | 1 +
>> drivers/clk/sunxi-ng/ccu-sun8i-r40.c | 1153
>> +++++++++++++++++++++++++++++
>> drivers/clk/sunxi-ng/ccu-sun8i-r40.h | 68 ++
>> include/dt-bindings/clock/sun8i-r40-ccu.h | 191 +++++
>> include/dt-bindings/reset/sun8i-r40-ccu.h | 129 ++++
>> 6 files changed, 1552 insertions(+)
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.c
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.h
>> create mode 100644 include/dt-bindings/clock/sun8i-r40-ccu.h
>> create mode 100644 include/dt-bindings/reset/sun8i-r40-ccu.h
>>
>> diff --git a/drivers/clk/sunxi-ng/Kconfig
>> b/drivers/clk/sunxi-ng/Kconfig
>> index 67acef3d2494..c11ad3375907 100644
>> --- a/drivers/clk/sunxi-ng/Kconfig
>> +++ b/drivers/clk/sunxi-ng/Kconfig
>> @@ -157,6 +157,16 @@ config SUN8I_DE2_CCU
>> select SUNXI_CCU_DIV
>> select SUNXI_CCU_GATE
>>
>> +config SUN8I_R40_CCU
>> + bool "Support for the Allwinner R40 CCU"
>> + select SUNXI_CCU_DIV
>> + select SUNXI_CCU_NK
>> + select SUNXI_CCU_NKM
>> + select SUNXI_CCU_NKMP
>> + select SUNXI_CCU_NM
>> + select SUNXI_CCU_MP
>
> You seem to be missing a few, such as CCU_GATE, CCU_MUX, CCU_PHASE.
> The list should at least be the same as the included headers.
>
>> + default MACH_SUN8I
>> +
>> config SUN9I_A80_CCU
>> bool "Support for the Allwinner A80 CCU"
>> select SUNXI_CCU_DIV
>> diff --git a/drivers/clk/sunxi-ng/Makefile
>> b/drivers/clk/sunxi-ng/Makefile
>> index 0185c6ffadcb..217db667a994 100644
>> --- a/drivers/clk/sunxi-ng/Makefile
>> +++ b/drivers/clk/sunxi-ng/Makefile
>> @@ -28,6 +28,7 @@ obj-$(CONFIG_SUN8I_H3_CCU) += ccu-sun8i-h3.o
>> obj-$(CONFIG_SUN8I_V3S_CCU) += ccu-sun8i-v3s.o
>> obj-$(CONFIG_SUN8I_DE2_CCU) += ccu-sun8i-de2.o
>> obj-$(CONFIG_SUN8I_R_CCU) += ccu-sun8i-r.o
>> +obj-$(CONFIG_SUN8I_R40_CCU) += ccu-sun8i-r40.o
>> obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80.o
>> obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-de.o
>> obj-$(CONFIG_SUN9I_A80_CCU) += ccu-sun9i-a80-usb.o
>> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
>> b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
>> new file mode 100644
>> index 000000000000..484a8956f59c
>> --- /dev/null
>> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.c
>> @@ -0,0 +1,1153 @@
>> +/*
>> + * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
>> + *
>> + * This software is licensed under the terms of the GNU General
>> Public
>> + * License version 2, as published by the Free Software Foundation,
>> and
>> + * may be copied, distributed, and modified under those terms.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/of_address.h>
>> +
>> +#include "ccu_common.h"
>> +#include "ccu_reset.h"
>> +
>> +#include "ccu_div.h"
>> +#include "ccu_gate.h"
>> +#include "ccu_mp.h"
>> +#include "ccu_mult.h"
>> +#include "ccu_nk.h"
>> +#include "ccu_nkm.h"
>> +#include "ccu_nkmp.h"
>> +#include "ccu_nm.h"
>> +#include "ccu_phase.h"
>> +
>> +#include "ccu-sun8i-r40.h"
>> +
>> +static SUNXI_CCU_NKMP_WITH_GATE_LOCK(pll_cpu_clk, "pll-cpu",
>> + "osc24M", 0x000,
>> + 8, 5, /* N */
>> + 4, 2, /* K */
>> + 0, 2, /* M */
>> + 16, 2, /* P */
>
> P does not do /8. Please add a limit.
>
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +/*
>> + * The Audio PLL is supposed to have 4 outputs: 3 fixed factors from
>> + * the base (2x, 4x and 8x), and one variable divider (the one true
>> + * pll audio).
>> + *
>> + * We don't have any need for the variable divider for now, so we
>> just
>> + * hardcode it to match with the clock names
>> + */
>> +#define SUN8I_R40_PLL_AUDIO_REG 0x008
>> +
>> +static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk,
>> "pll-audio-base",
>> + "osc24M", 0x008,
>> + 8, 7, /* N */
>> + 0, 5, /* M */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video0_clk, "pll-video0",
>> + "osc24M", 0x0010,
>> + 8, 7, /* N */
>> + 0, 4, /* M */
>> + BIT(24), /* frac enable */
>> + BIT(25), /* frac select */
>> + 270000000, /* frac rate 0 */
>> + 297000000, /* frac rate 1 */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_ve_clk, "pll-ve",
>> + "osc24M", 0x0018,
>> + 8, 7, /* N */
>> + 0, 4, /* M */
>> + BIT(24), /* frac enable */
>> + BIT(25), /* frac select */
>> + 270000000, /* frac rate 0 */
>> + 297000000, /* frac rate 1 */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_ddr0_clk, "pll-ddr0",
>> + "osc24M", 0x020,
>> + 8, 5, /* N */
>> + 4, 2, /* K */
>> + 0, 2, /* M */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +/* According to the BSP driver, pll-periph{0,1} have M at 0:1 */
>
> This is also mentioned in the user manual. You can leave it out.
>
> Also, please leave a note mentioning that support for the SATA clock
> output of the peripheral PLL is not implemented here.
>
>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_periph0_clk, "pll-periph0",
>> + "osc24M", 0x028,
>> + 8, 5, /* N */
>> + 4, 2, /* K */
>> + 0, 2, /* M */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_periph1_clk, "pll-periph1",
>> + "osc24M", 0x02c,
>> + 8, 5, /* N */
>> + 4, 2, /* K */
>> + 0, 2, /* M */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video1_clk, "pll-video1",
>> + "osc24M", 0x030,
>> + 8, 7, /* N */
>> + 0, 4, /* M */
>> + BIT(24), /* frac enable */
>> + BIT(25), /* frac select */
>> + 270000000, /* frac rate 0 */
>> + 297000000, /* frac rate 1 */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + CLK_SET_RATE_UNGATE);
>
> Why do you have this set for only some of the PLLs? Either you need it
> for all of them, or you don't need it for any of them.
>
>> +
>> +/*
>> + * For the special bit in gate part, please see the BSP source code
>> at
>> + *
>> https://github.com/BPI-SINOVOIP/BPI-M2U-bsp/blob/master/linux-sunxi/drivers/clk/sunxi/clk-sun8iw11.c#L665
>> + */
>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_sata_clk, "pll-sata",
>> + "osc24M", 0x034,
>> + 8, 5, /* N */
>> + 4, 2, /* K */
>> + 0, 2, /* M */
>> + BIT(31) | BIT(14), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>
> I think this is a somewhat simplified approach. From what I understand
> of the user manual, the SATA clock path look like:
>
>
> [ PLL-PERIPH0-SATA ] -\
> mux @ 0x34 bit 30 --- gate @ 0x34 bit 14 --- ...
> [ PLL-SATA ] ---------/
>
> ... from above ... ------\
> mux @ 0xc8 bit 24 --- gate @ 0xc8 bit 31
> [ external oscillator ] -/
>
> If you choose to simplify the implementation, please include a detailed
> note as to why you chose to do so, and the validity of the
> simplification.
I think it can be fully implemented...
But how should I call the internal clock controlled by the mux @ 0x34
bit 30?
>
>> +
>> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_gpu_clk, "pll-gpu",
>> + "osc24M", 0x038,
>> + 8, 7, /* N */
>> + 0, 4, /* M */
>> + BIT(24), /* frac enable */
>> + BIT(25), /* frac select */
>> + 270000000, /* frac rate 0 */
>> + 297000000, /* frac rate 1 */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static const char * const pll_mipi_parents[] = { "pll-video0",
>> "pll-video1" };
>
> pll-video1 is not listed in the manual.
>
>> +static SUNXI_CCU_NKM_WITH_MUX_GATE_LOCK(pll_mipi_clk, "pll-mipi",
>> + pll_mipi_parents, 0x040,
>> + 8, 4, /* N */
>> + 4, 2, /* K */
>> + 0, 4, /* M */
>> + 21, 0, /* mux */
>> + BIT(31) | BIT(23) | BIT(22), /* gate */
>> + BIT(28), /* lock */
>> + CLK_SET_RATE_UNGATE);
>
> Please leave a note mentioning that you only implement support for the
> "MIPI" mode.
> You should also force it at probe time. See the driver for the A31.
>
>> +
>> +static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
>> + "osc24M", 0x0048,
>> + 8, 7, /* N */
>> + 0, 4, /* M */
>> + BIT(24), /* frac enable */
>> + BIT(25), /* frac select */
>> + 270000000, /* frac rate 0 */
>> + 297000000, /* frac rate 1 */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + 0);
>> +
>> +static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
>> + "osc24M", 0x04c,
>> + 8, 7, /* N */
>
> N has minimum and maximum limits.
>
>> + 0, 2, /* M */
>> + BIT(31), /* gate */
>> + BIT(28), /* lock */
>> + CLK_SET_RATE_UNGATE);
>> +
>> +static const char * const cpu_parents[] = { "osc32k", "osc24M",
>> + "pll-cpu", "pll-cpu" };
>> +static SUNXI_CCU_MUX(cpu_clk, "cpu", cpu_parents,
>> + 0x050, 16, 2, CLK_IS_CRITICAL);
>> +
>> +static SUNXI_CCU_M(axi_clk, "axi", "cpu", 0x050, 0, 2, 0);
>> +
>> +static const char * const ahb1_parents[] = { "osc32k", "osc24M",
>> + "axi", "pll-periph0" };
>> +static const struct ccu_mux_var_prediv ahb1_predivs[] = {
>> + { .index = 3, .shift = 6, .width = 2 },
>> +};
>> +static struct ccu_div ahb1_clk = {
>> + .div = _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
>> +
>> + .mux = {
>> + .shift = 12,
>> + .width = 2,
>> +
>> + .var_predivs = ahb1_predivs,
>> + .n_var_predivs = ARRAY_SIZE(ahb1_predivs),
>> + },
>> +
>> + .common = {
>> + .reg = 0x054,
>> + .features = CCU_FEATURE_VARIABLE_PREDIV,
>> + .hw.init = CLK_HW_INIT_PARENTS("ahb1",
>> + ahb1_parents,
>> + &ccu_div_ops,
>> + 0),
>> + },
>> +};
>> +
>> +static struct clk_div_table apb1_div_table[] = {
>> + { .val = 0, .div = 2 },
>> + { .val = 1, .div = 2 },
>> + { .val = 2, .div = 4 },
>> + { .val = 3, .div = 8 },
>> + { /* Sentinel */ },
>> +};
>> +static SUNXI_CCU_DIV_TABLE(apb1_clk, "apb1", "ahb1",
>> + 0x054, 8, 2, apb1_div_table, 0);
>> +
>> +static const char * const apb2_parents[] = { "osc32k", "osc24M",
>> + "pll-periph0-2x",
>> + "pll-periph0-2x" };
>> +static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", apb2_parents, 0x058,
>> + 0, 5, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + 0);
>> +
>> +static SUNXI_CCU_GATE(bus_mipi_dsi_clk, "bus-mipi-dsi", "ahb1",
>> + 0x060, BIT(1), 0);
>> +static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "ahb1",
>> + 0x060, BIT(5), 0);
>> +static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "ahb1",
>> + 0x060, BIT(6), 0);
>> +static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb1",
>> + 0x060, BIT(8), 0);
>> +static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb1",
>> + 0x060, BIT(9), 0);
>> +static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb1",
>> + 0x060, BIT(10), 0);
>> +static SUNXI_CCU_GATE(bus_mmc3_clk, "bus-mmc3", "ahb1",
>> + 0x060, BIT(11), 0);
>> +static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb1",
>> + 0x060, BIT(13), 0);
>> +static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "ahb1",
>> + 0x060, BIT(14), 0);
>> +static SUNXI_CCU_GATE(bus_emac_clk, "bus-emac", "ahb1",
>> + 0x060, BIT(17), 0);
>> +static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb1",
>> + 0x060, BIT(18), 0);
>> +static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "ahb1",
>> + 0x060, BIT(19), 0);
>> +static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb1",
>> + 0x060, BIT(20), 0);
>> +static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb1",
>> + 0x060, BIT(21), 0);
>> +static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb1",
>> + 0x060, BIT(22), 0);
>> +static SUNXI_CCU_GATE(bus_spi3_clk, "bus-spi3", "ahb1",
>> + 0x060, BIT(23), 0);
>> +static SUNXI_CCU_GATE(bus_sata_clk, "bus-sata", "ahb1",
>> + 0x060, BIT(24), 0);
>> +static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb1",
>> + 0x060, BIT(25), 0);
>> +static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb1",
>> + 0x060, BIT(26), 0);
>> +static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb1",
>> + 0x060, BIT(27), 0);
>> +static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb1",
>> + 0x060, BIT(28), 0);
>> +static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb1",
>> + 0x060, BIT(29), 0);
>> +static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb1",
>> + 0x060, BIT(30), 0);
>> +static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb1",
>> + 0x060, BIT(31), 0);
>> +
>> +static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "ahb1",
>> + 0x064, BIT(0), 0);
>> +static SUNXI_CCU_GATE(bus_de_mp_clk, "bus-de-mp", "ahb1",
>> + 0x064, BIT(2), 0);
>
> The mixer processor is unrelated to the display engine.
> Please drop the "de" part of the name.
>
>> +static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "ahb1",
>> + 0x064, BIT(5), 0);
>> +static SUNXI_CCU_GATE(bus_csi0_clk, "bus-csi0", "ahb1",
>> + 0x064, BIT(8), 0);
>> +static SUNXI_CCU_GATE(bus_csi1_clk, "bus-csi1", "ahb1",
>> + 0x064, BIT(9), 0);
>> +static SUNXI_CCU_GATE(bus_hdmi_slow_clk, "bus-hdmi-slow", "ahb1",
>> + 0x064, BIT(10), 0);
>> +static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb1",
>> + 0x064, BIT(11), 0);
>
> Please stick to the names in the user manual.
> They are hdmi0 and hdmi1.
>
>> +static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "ahb1",
>> + 0x064, BIT(12), 0);
>> +static SUNXI_CCU_GATE(bus_tve0_clk, "bus-tve0", "ahb1",
>> + 0x064, BIT(13), 0);
>> +static SUNXI_CCU_GATE(bus_tve1_clk, "bus-tve1", "ahb1",
>> + 0x064, BIT(14), 0);
>> +static SUNXI_CCU_GATE(bus_tve_top_clk, "bus-tve-top", "ahb1",
>> + 0x064, BIT(15), 0);
>> +static SUNXI_CCU_GATE(bus_gmac_clk, "bus-gmac", "ahb1",
>> + 0x064, BIT(17), 0);
>> +static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "ahb1",
>> + 0x064, BIT(20), 0);
>> +static SUNXI_CCU_GATE(bus_tvd0_clk, "bus-tvd0", "ahb1",
>> + 0x064, BIT(21), 0);
>> +static SUNXI_CCU_GATE(bus_tvd1_clk, "bus-tvd1", "ahb1",
>> + 0x064, BIT(22), 0);
>> +static SUNXI_CCU_GATE(bus_tvd2_clk, "bus-tvd2", "ahb1",
>> + 0x064, BIT(23), 0);
>> +static SUNXI_CCU_GATE(bus_tvd3_clk, "bus-tvd3", "ahb1",
>> + 0x064, BIT(24), 0);
>> +static SUNXI_CCU_GATE(bus_tvd_top_clk, "bus-tvd-top", "ahb1",
>> + 0x064, BIT(25), 0);
>> +static SUNXI_CCU_GATE(bus_tcon0_clk, "bus-tcon0", "ahb1",
>> + 0x064, BIT(26), 0);
>> +static SUNXI_CCU_GATE(bus_tcon1_clk, "bus-tcon1", "ahb1",
>> + 0x064, BIT(27), 0);
>> +static SUNXI_CCU_GATE(bus_tve0_tcon_clk, "bus-tve0-tcon", "ahb1",
>> + 0x064, BIT(28), 0);
>> +static SUNXI_CCU_GATE(bus_tve1_tcon_clk, "bus-tve1-tcon", "ahb1",
>> + 0x064, BIT(29), 0);
>
> Please stick to the names used in the user manual.
> They are "tcon-lcdN" and "tcon-tvN".
>
>> +static SUNXI_CCU_GATE(bus_tcon_top_clk, "bus-tcon-top", "ahb1",
>> + 0x064, BIT(30), 0);
>> +
>> +static SUNXI_CCU_GATE(bus_codec_clk, "bus-codec", "apb1",
>> + 0x068, BIT(0), 0);
>> +static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1",
>> + 0x068, BIT(1), 0);
>> +static SUNXI_CCU_GATE(bus_ac97_clk, "bus-ac97", "apb1",
>> + 0x068, BIT(2), 0);
>> +static SUNXI_CCU_GATE(bus_pio_clk, "bus-pio", "apb1",
>> + 0x068, BIT(5), 0);
>> +static SUNXI_CCU_GATE(bus_ir0_clk, "bus-ir0", "apb1",
>> + 0x068, BIT(6), 0);
>> +static SUNXI_CCU_GATE(bus_ir1_clk, "bus-ir1", "apb1",
>> + 0x068, BIT(7), 0);
>> +static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1",
>> + 0x068, BIT(8), 0);
>> +static SUNXI_CCU_GATE(bus_keypad_clk, "bus-keypad", "apb1",
>> + 0x068, BIT(10), 0);
>> +static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1",
>> + 0x068, BIT(12), 0);
>> +static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1",
>> + 0x068, BIT(13), 0);
>> +static SUNXI_CCU_GATE(bus_i2s2_clk, "bus-i2s2", "apb1",
>> + 0x068, BIT(14), 0);
>> +
>> +static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2",
>> + 0x06c, BIT(0), 0);
>> +static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2",
>> + 0x06c, BIT(1), 0);
>> +static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2",
>> + 0x06c, BIT(2), 0);
>> +static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2",
>> + 0x06c, BIT(3), 0);
>> +/*
>> + * In datasheet here's "Reserved", however the gate exists in BSP
>> soucre
>> + * code.
>> + */
>> +static SUNXI_CCU_GATE(bus_can_clk, "bus-can", "apb2",
>> + 0x06c, BIT(4), 0);
>> +static SUNXI_CCU_GATE(bus_scr_clk, "bus-scr", "apb2",
>> + 0x06c, BIT(5), 0);
>> +static SUNXI_CCU_GATE(bus_ps20_clk, "bus-ps20", "apb2",
>> + 0x06c, BIT(6), 0);
>> +static SUNXI_CCU_GATE(bus_ps21_clk, "bus-ps21", "apb2",
>> + 0x06c, BIT(7), 0);
>> +static SUNXI_CCU_GATE(bus_i2c4_clk, "bus-i2c4", "apb2",
>> + 0x06c, BIT(15), 0);
>> +static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2",
>> + 0x06c, BIT(16), 0);
>> +static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2",
>> + 0x06c, BIT(17), 0);
>> +static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
>> + 0x06c, BIT(18), 0);
>> +static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
>> + 0x06c, BIT(19), 0);
>> +static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2",
>> + 0x06c, BIT(20), 0);
>> +static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2",
>> + 0x06c, BIT(21), 0);
>> +static SUNXI_CCU_GATE(bus_uart6_clk, "bus-uart6", "apb2",
>> + 0x06c, BIT(22), 0);
>> +static SUNXI_CCU_GATE(bus_uart7_clk, "bus-uart7", "apb2",
>> + 0x06c, BIT(23), 0);
>> +
>> +/* Educated guess: the BSP clock driver do not have this clock */
>
> The gate is documented in the user manual. What part is a guess?
>
>> +static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "ahb1",
>> + 0x070, BIT(7), 0);
>> +
>> +static SUNXI_CCU_M_WITH_GATE(ths_clk, "ths", "osc24M",
>> + 0x074, 0, 2, BIT(31), 0);
>
> This clock has a mux. Even with only one parent, you should still
> implement the mux, so the kernel can recover from cases where some
> other piece of software left it in a bad state.
>
> Also the divider is of the power of two type.
>
>> +
>> +static const char * const mod0_default_parents[] = { "osc24M",
>> "pll-periph0",
>> + "pll-periph1" };
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand",
>> mod0_default_parents, 0x080,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0",
>> mod0_default_parents, 0x088,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1",
>> mod0_default_parents, 0x08c,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2",
>> mod0_default_parents, 0x090,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(mmc3_clk, "mmc3",
>> mod0_default_parents, 0x094,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static const char * const ts_parents[] = { "osc24M", "pll-periph0",
>> };
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x098,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>
> The mux is 4 bits wide.
>
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static const char * const ce_parents[] = { "osc24M",
>> "pll-periph0-2x",
>> + "pll-periph1-2x" };
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x09c,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0",
>> mod0_default_parents, 0x0a0,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1",
>> mod0_default_parents, 0x0a4,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2",
>> mod0_default_parents, 0x0a8,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(spi3_clk, "spi3",
>> mod0_default_parents, 0x0ac,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static const char * const i2s_parents[] = { "pll-audio-8x",
>> "pll-audio-4x",
>> + "pll-audio-2x", "pll-audio" };
>> +static SUNXI_CCU_MUX_WITH_GATE(i2s0_clk, "i2s0", i2s_parents,
>> + 0x0b0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
>> +
>> +static SUNXI_CCU_MUX_WITH_GATE(i2s1_clk, "i2s1", i2s_parents,
>> + 0x0b4, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
>> +
>> +static SUNXI_CCU_MUX_WITH_GATE(i2s2_clk, "i2s2", i2s_parents,
>> + 0x0b8, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
>> +
>> +static SUNXI_CCU_MUX_WITH_GATE(ac97_clk, "ac97", i2s_parents,
>> + 0x0bc, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
>> +
>> +static SUNXI_CCU_MUX_WITH_GATE(spdif_clk, "spdif", i2s_parents,
>> + 0x0c0, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
>> +
>> +static const char * const keypad_parents[] = { "osc24M", "osc32k", };
>
> The parents are not sequential. You need a mux table here.
>
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(keypad_clk, "keypad",
>> keypad_parents, 0x0c4,
>> + 0, 5, /* M */
>> + 16, 2, /* P */
>> + 25, 1, /* mux */
>
> Mux is 2 bits wide.
>
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static const char * const sata_parents[] = { "pll-sata", "sata-ext",
>> };
>> +static SUNXI_CCU_MUX_WITH_GATE(sata_clk, "sata", sata_parents,
>> + 0x0c8, 24, 1, BIT(31), CLK_SET_RATE_PARENT);
>> +
>> +static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M",
>> + 0x0cc, BIT(8), 0);
>> +static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M",
>> + 0x0cc, BIT(9), 0);
>> +static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M",
>> + 0x0cc, BIT(10), 0);
>> +static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc24M",
>> + 0x0cc, BIT(16), 0);
>> +static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc24M",
>> + 0x0cc, BIT(17), 0);
>> +static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc24M",
>> + 0x0cc, BIT(18), 0);
>
> Why bother with the 3 clocks below, if you aren't going to use them as
> parents
> for the 3 usb-ohci gates above? The user manual states the gates are
> for both
> 48M and 12M clocks.
>
>> +
>> +static const char * const usb_ohci12m_parents[] = { "osc24M-2x",
>> "osc24M",
>> + "osc32k" };
>
> You should have pre-dividers here so the clk subsystem can report
> correct
> clk rates.
>
>> +static SUNXI_CCU_MUX(usb_ohci0_12m_clk, "usb-ohci0-12m",
>> usb_ohci12m_parents,
>> + 0x0cc, 20, 2, 0);
>> +static SUNXI_CCU_MUX(usb_ohci1_12m_clk, "usb-ohci1-12m",
>> usb_ohci12m_parents,
>> + 0x0cc, 22, 2, 0);
>> +static SUNXI_CCU_MUX(usb_ohci2_12m_clk, "usb-ohci2-12m",
>> usb_ohci12m_parents,
>> + 0x0cc, 24, 2, 0);
>> +
>> +static const char * const ir_parents[] = { "osc24M", "pll-periph0",
>> + "pll-periph1", "osc32k" };
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(ir0_clk, "ir0", ir_parents, 0x0d0,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(ir1_clk, "ir1", ir_parents, 0x0d4,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1"
>> };
>> +static SUNXI_CCU_M_WITH_MUX(dram_clk, "dram", dram_parents,
>> + 0x0f4, 0, 2, 20, 2, CLK_IS_CRITICAL);
>> +
>> +static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "dram",
>> + 0x100, BIT(0), 0);
>> +static SUNXI_CCU_GATE(dram_csi0_clk, "dram-csi0", "dram",
>> + 0x100, BIT(1), 0);
>> +static SUNXI_CCU_GATE(dram_csi1_clk, "dram-csi1", "dram",
>> + 0x100, BIT(2), 0);
>> +static SUNXI_CCU_GATE(dram_ts_clk, "dram-ts", "dram",
>> + 0x100, BIT(3), 0);
>> +static SUNXI_CCU_GATE(dram_tvd_clk, "dram-tvd", "dram",
>> + 0x100, BIT(4), 0);
>> +static SUNXI_CCU_GATE(dram_de_mp_clk, "dram-de-mp", "dram",
>> + 0x100, BIT(5), 0);
>
> Same thing about the mixer processor as before.
>
>> +static
>> SUNXI_CCU_GATE(dram_deinterlace_clk, "dram-deinterlace", "dram",
>> + 0x100, BIT(6), 0);
>> +
>> +static const char * const de_parents[] = { "pll-periph0-2x", "pll-de"
>> };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents,
>> + 0x104, 0, 4, 24, 3, BIT(31), 0);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(de_mp_clk, "de-mp", de_parents,
>> + 0x108, 0, 4, 24, 3, BIT(31), 0);
>> +
>> +static const char * const tcon_parents[] = { "pll-video0",
>> "pll-video1",
>> + "pll-video0-2x", "pll-video1-2x",
>> + "pll-mipi" };
>> +static SUNXI_CCU_MUX_WITH_GATE(tcon0_clk, "tcon0", tcon_parents,
>> + 0x110, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
>> +static SUNXI_CCU_MUX_WITH_GATE(tcon1_clk, "tcon1", tcon_parents,
>> + 0x114, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tcon_tve0_clk, "tcon-tve0",
>> tcon_parents,
>> + 0x118, 0, 4, 24, 3, BIT(31), 0);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tcon_tve1_clk, "tcon-tve1",
>> tcon_parents,
>> + 0x11c, 0, 4, 24, 3, BIT(31), 0);
>
> Again, please stick to the names used by the user manual.
>
>> +
>> +static const char * const deinterlace_parents[] = { "pll-periph0",
>> + "pll-periph1" };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace",
>> + deinterlace_parents, 0x124, 0, 4, 24, 3,
>> + BIT(31), 0);
>> +
>> +static const char * const csi_mclk_parents[] = { "osc24M",
>> "pll-video",
>> + "pll-periph1" };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(csi1_mclk_clk, "csi1-mclk",
>> csi_mclk_parents,
>> + 0x130, 0, 5, 8, 3, BIT(15), 0);
>> +
>> +static const char * const csi_sclk_parents[] = { "pll-periph0",
>> "pll-periph1" };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(csi_sclk_clk, "csi-sclk",
>> csi_sclk_parents,
>> + 0x134, 16, 4, 24, 3, BIT(31), 0);
>> +
>> +static SUNXI_CCU_M_WITH_MUX_GATE(csi0_mclk_clk, "csi0-mclk",
>> csi_mclk_parents,
>> + 0x134, 0, 5, 8, 3, BIT(15), 0);
>> +
>> +static SUNXI_CCU_M_WITH_GATE(ve_clk, "ve", "pll-ve",
>> + 0x13c, 16, 3, BIT(31), 0);
>> +
>> +static SUNXI_CCU_GATE(adda_clk, "adda", "pll-audio",
>> + 0x140, BIT(31), CLK_SET_RATE_PARENT);
>> +static SUNXI_CCU_GATE(adda_4x_clk, "adda-4x", "pll-audio-4x",
>> + 0x140, BIT(30), CLK_SET_RATE_PARENT);
>
> adda-4x is not listed in the user manual. Does it really exist?
> Is it used anywhere?
>
>> +static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M",
>> + 0x144, BIT(31), 0);
>> +
>> +static const char * const hdmi_parents[] = { "pll-video0",
>> "pll-video1" };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents,
>> + 0x150, 0, 4, 24, 2, BIT(31), 0);
>> +
>> +static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M",
>> + 0x154, BIT(31), 0);
>> +
>> +static const char * const mbus_parents[] = { "osc24M",
>> "pll-periph0-2x",
>> + "pll-ddr0" };
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
>> 0x15c,
>> + 0, 4, /* M */
>> + 16, 2, /* P */
>
> Curiously, the formula for clk rate calculation does not include this
> factor.
>
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + CLK_IS_CRITICAL);
>> +
>> +static const char * const mipi_dsi_parents[] = { "pll-video0",
>> "pll-video1",
>> + "pll-periph0" };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(mipi_dsi_clk, "mipi-dsi",
>> mipi_dsi_parents,
>> + 0x168, 0, 4, 8, 2, BIT(15), 0);
>
> This is called "dsi-dphy" in the user manual. Looking at the A31,
> it had "dsi-sclk" in the upper 16 bits. So please use "dsi-dphy"
> or "mipi-dsi-dphy" here.
>
>> +
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tve0_clk, "tve0", tcon_parents,
>> + 0x180, 0, 4, 24, 3, BIT(31), 0);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tve1_clk, "tve1", tcon_parents,
>> + 0x184, 0, 4, 24, 3, BIT(31), 0);
>> +
>> +static const char * const tvd_parents[] = { "pll-video0",
>> "pll-video1",
>> + "pll-video0-2x", "pll-video1-2x" };
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd0_clk, "tvd0", tvd_parents,
>> + 0x188, 0, 4, 24, 2, BIT(31), 0);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd1_clk, "tvd1", tvd_parents,
>> + 0x18c, 0, 4, 24, 2, BIT(31), 0);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd2_clk, "tvd2", tvd_parents,
>> + 0x190, 0, 4, 24, 2, BIT(31), 0);
>> +static SUNXI_CCU_M_WITH_MUX_GATE(tvd3_clk, "tvd3", tvd_parents,
>> + 0x194, 0, 4, 24, 2, BIT(31), 0);
>
> The mux is 3 bits wide for the tvd clocks.
>
>> +
>> +static SUNXI_CCU_M_WITH_GATE(gpu_clk, "gpu", "pll-gpu",
>> + 0x1a0, 0, 3, BIT(31), 0);
>
> You should probably have CLK_SET_RATE_PARENT here.
>
>> +
>> +static const char * const out_parents[] = { "osc24M-32k", "osc32k",
>> "osc24M" };
>
> Please use pre-dividers instead of "osc24M-32k".
>
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(outa_clk, "outa", out_parents,
>> 0x1f0,
>> + 8, 5, /* M */
>> + 20, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +static SUNXI_CCU_MP_WITH_MUX_GATE(outb_clk, "outb", out_parents,
>> 0x1f4,
>> + 8, 5, /* M */
>> + 20, 2, /* P */
>> + 24, 2, /* mux */
>> + BIT(31), /* gate */
>> + 0);
>> +
>> +static struct ccu_common *sun8i_r40_ccu_clks[] = {
>> + &pll_cpu_clk.common,
>> + &pll_audio_base_clk.common,
>> + &pll_video0_clk.common,
>> + &pll_ve_clk.common,
>> + &pll_ddr0_clk.common,
>> + &pll_periph0_clk.common,
>> + &pll_periph1_clk.common,
>> + &pll_video1_clk.common,
>> + &pll_sata_clk.common,
>> + &pll_gpu_clk.common,
>> + &pll_mipi_clk.common,
>> + &pll_de_clk.common,
>> + &pll_ddr1_clk.common,
>> + &cpu_clk.common,
>> + &axi_clk.common,
>> + &ahb1_clk.common,
>> + &apb1_clk.common,
>> + &apb2_clk.common,
>> + &bus_mipi_dsi_clk.common,
>> + &bus_ce_clk.common,
>> + &bus_dma_clk.common,
>> + &bus_mmc0_clk.common,
>> + &bus_mmc1_clk.common,
>> + &bus_mmc2_clk.common,
>> + &bus_mmc3_clk.common,
>> + &bus_nand_clk.common,
>> + &bus_dram_clk.common,
>> + &bus_emac_clk.common,
>> + &bus_ts_clk.common,
>> + &bus_hstimer_clk.common,
>> + &bus_spi0_clk.common,
>> + &bus_spi1_clk.common,
>> + &bus_spi2_clk.common,
>> + &bus_spi3_clk.common,
>> + &bus_sata_clk.common,
>> + &bus_otg_clk.common,
>> + &bus_ehci0_clk.common,
>> + &bus_ehci1_clk.common,
>> + &bus_ehci2_clk.common,
>> + &bus_ohci0_clk.common,
>> + &bus_ohci1_clk.common,
>> + &bus_ohci2_clk.common,
>> + &bus_ve_clk.common,
>> + &bus_de_mp_clk.common,
>> + &bus_deinterlace_clk.common,
>> + &bus_csi0_clk.common,
>> + &bus_csi1_clk.common,
>> + &bus_hdmi_slow_clk.common,
>> + &bus_hdmi_clk.common,
>> + &bus_de_clk.common,
>> + &bus_tve0_clk.common,
>> + &bus_tve1_clk.common,
>> + &bus_tve_top_clk.common,
>> + &bus_gmac_clk.common,
>> + &bus_gpu_clk.common,
>> + &bus_tvd0_clk.common,
>> + &bus_tvd1_clk.common,
>> + &bus_tvd2_clk.common,
>> + &bus_tvd3_clk.common,
>> + &bus_tvd_top_clk.common,
>> + &bus_tcon0_clk.common,
>> + &bus_tcon1_clk.common,
>> + &bus_tve0_tcon_clk.common,
>> + &bus_tve1_tcon_clk.common,
>> + &bus_tcon_top_clk.common,
>> + &bus_codec_clk.common,
>> + &bus_spdif_clk.common,
>> + &bus_ac97_clk.common,
>> + &bus_pio_clk.common,
>> + &bus_ir0_clk.common,
>> + &bus_ir1_clk.common,
>> + &bus_ths_clk.common,
>> + &bus_keypad_clk.common,
>> + &bus_i2s0_clk.common,
>> + &bus_i2s1_clk.common,
>> + &bus_i2s2_clk.common,
>> + &bus_i2c0_clk.common,
>> + &bus_i2c1_clk.common,
>> + &bus_i2c2_clk.common,
>> + &bus_i2c3_clk.common,
>> + &bus_can_clk.common,
>> + &bus_scr_clk.common,
>> + &bus_ps20_clk.common,
>> + &bus_ps21_clk.common,
>> + &bus_i2c4_clk.common,
>> + &bus_uart0_clk.common,
>> + &bus_uart1_clk.common,
>> + &bus_uart2_clk.common,
>> + &bus_uart3_clk.common,
>> + &bus_uart4_clk.common,
>> + &bus_uart5_clk.common,
>> + &bus_uart6_clk.common,
>> + &bus_uart7_clk.common,
>> + &bus_dbg_clk.common,
>> + &ths_clk.common,
>> + &nand_clk.common,
>> + &mmc0_clk.common,
>> + &mmc1_clk.common,
>> + &mmc2_clk.common,
>> + &mmc3_clk.common,
>> + &ts_clk.common,
>> + &ce_clk.common,
>> + &spi0_clk.common,
>> + &spi1_clk.common,
>> + &spi2_clk.common,
>> + &spi3_clk.common,
>> + &i2s0_clk.common,
>> + &i2s1_clk.common,
>> + &i2s2_clk.common,
>> + &ac97_clk.common,
>> + &spdif_clk.common,
>> + &keypad_clk.common,
>> + &sata_clk.common,
>> + &usb_phy0_clk.common,
>> + &usb_phy1_clk.common,
>> + &usb_phy2_clk.common,
>> + &usb_ohci0_clk.common,
>> + &usb_ohci1_clk.common,
>> + &usb_ohci2_clk.common,
>> + &usb_ohci0_12m_clk.common,
>> + &usb_ohci1_12m_clk.common,
>> + &usb_ohci2_12m_clk.common,
>> + &ir0_clk.common,
>> + &ir1_clk.common,
>> + &dram_clk.common,
>> + &dram_ve_clk.common,
>> + &dram_csi0_clk.common,
>> + &dram_csi1_clk.common,
>> + &dram_ts_clk.common,
>> + &dram_tvd_clk.common,
>> + &dram_de_mp_clk.common,
>> + &dram_deinterlace_clk.common,
>> + &de_clk.common,
>> + &de_mp_clk.common,
>> + &tcon0_clk.common,
>> + &tcon1_clk.common,
>> + &tcon_tve0_clk.common,
>> + &tcon_tve1_clk.common,
>> + &deinterlace_clk.common,
>> + &csi1_mclk_clk.common,
>> + &csi_sclk_clk.common,
>> + &csi0_mclk_clk.common,
>> + &ve_clk.common,
>> + &adda_clk.common,
>> + &adda_4x_clk.common,
>> + &avs_clk.common,
>> + &hdmi_clk.common,
>> + &hdmi_slow_clk.common,
>> + &mbus_clk.common,
>> + &mipi_dsi_clk.common,
>> + &tve0_clk.common,
>> + &tve1_clk.common,
>> + &tvd0_clk.common,
>> + &tvd1_clk.common,
>> + &tvd2_clk.common,
>> + &tvd3_clk.common,
>> + &gpu_clk.common,
>> + &outa_clk.common,
>> + &outb_clk.common,
>> +};
>> +
>> +/* We hardcode the divider to 4 for now */
>> +static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
>> + "pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
>> +static CLK_FIXED_FACTOR(pll_audio_2x_clk, "pll-audio-2x",
>> + "pll-audio-base", 2, 1, CLK_SET_RATE_PARENT);
>> +static CLK_FIXED_FACTOR(pll_audio_4x_clk, "pll-audio-4x",
>> + "pll-audio-base", 1, 1, CLK_SET_RATE_PARENT);
>> +static CLK_FIXED_FACTOR(pll_audio_8x_clk, "pll-audio-8x",
>> + "pll-audio-base", 1, 2, CLK_SET_RATE_PARENT);
>> +static CLK_FIXED_FACTOR(pll_periph0_2x_clk, "pll-periph0-2x",
>> + "pll-periph0", 1, 2, 0);
>> +static CLK_FIXED_FACTOR(pll_periph1_2x_clk, "pll-periph1-2x",
>> + "pll-periph1", 1, 2, 0);
>> +static CLK_FIXED_FACTOR(pll_video0_2x_clk, "pll-video0-2x",
>> + "pll-video0", 1, 2, 0);
>> +static CLK_FIXED_FACTOR(pll_video1_2x_clk, "pll-video1-2x",
>> + "pll-video1", 1, 2, 0);
>> +static CLK_FIXED_FACTOR(osc24m_2x_clk, "osc24M-2x",
>> + "osc24M", 1, 2, 0);
>> +static CLK_FIXED_FACTOR(osc24m_32k_clk, "osc24M-32k",
>> + "osc24M", 750, 1, 0);
>
> As mentioned above, please drop the last one.
>
>> +
>> +static struct clk_hw_onecell_data sun8i_r40_hw_clks = {
>> + .hws = {
>> + [CLK_OSC24M_2X] = &osc24m_2x_clk.hw,
>> + [CLK_OSC24M_32K] = &osc24m_32k_clk.hw,
>> + [CLK_PLL_CPU] = &pll_cpu_clk.common.hw,
>> + [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
>> + [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
>> + [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
>> + [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
>> + [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
>> + [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
>> + [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
>> + [CLK_PLL_VE] = &pll_ve_clk.common.hw,
>> + [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
>> + [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
>> + [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
>> + [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
>> + [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
>> + [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
>> + [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
>> + [CLK_PLL_SATA] = &pll_sata_clk.common.hw,
>> + [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
>> + [CLK_PLL_MIPI] = &pll_mipi_clk.common.hw,
>> + [CLK_PLL_DE] = &pll_de_clk.common.hw,
>> + [CLK_PLL_DDR1] = &pll_ddr1_clk.common.hw,
>> + [CLK_CPU] = &cpu_clk.common.hw,
>> + [CLK_AXI] = &axi_clk.common.hw,
>> + [CLK_AHB1] = &ahb1_clk.common.hw,
>> + [CLK_APB1] = &apb1_clk.common.hw,
>> + [CLK_APB2] = &apb2_clk.common.hw,
>> + [CLK_BUS_MIPI_DSI] = &bus_mipi_dsi_clk.common.hw,
>> + [CLK_BUS_CE] = &bus_ce_clk.common.hw,
>> + [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
>> + [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
>> + [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
>> + [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
>> + [CLK_BUS_MMC3] = &bus_mmc3_clk.common.hw,
>> + [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
>> + [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
>> + [CLK_BUS_EMAC] = &bus_emac_clk.common.hw,
>> + [CLK_BUS_TS] = &bus_ts_clk.common.hw,
>> + [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
>> + [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
>> + [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
>> + [CLK_BUS_SPI2] = &bus_spi2_clk.common.hw,
>> + [CLK_BUS_SPI3] = &bus_spi3_clk.common.hw,
>> + [CLK_BUS_SATA] = &bus_sata_clk.common.hw,
>> + [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
>> + [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
>> + [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
>> + [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
>> + [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
>> + [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
>> + [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
>> + [CLK_BUS_VE] = &bus_ve_clk.common.hw,
>> + [CLK_BUS_DE_MP] = &bus_de_mp_clk.common.hw,
>> + [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
>> + [CLK_BUS_CSI0] = &bus_csi0_clk.common.hw,
>> + [CLK_BUS_CSI1] = &bus_csi1_clk.common.hw,
>> + [CLK_BUS_HDMI_SLOW] = &bus_hdmi_slow_clk.common.hw,
>> + [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
>> + [CLK_BUS_DE] = &bus_de_clk.common.hw,
>> + [CLK_BUS_TVE0] = &bus_tve0_clk.common.hw,
>> + [CLK_BUS_TVE1] = &bus_tve1_clk.common.hw,
>> + [CLK_BUS_TVE_TOP] = &bus_tve_top_clk.common.hw,
>> + [CLK_BUS_GMAC] = &bus_gmac_clk.common.hw,
>> + [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
>> + [CLK_BUS_TVD0] = &bus_tvd0_clk.common.hw,
>> + [CLK_BUS_TVD1] = &bus_tvd1_clk.common.hw,
>> + [CLK_BUS_TVD2] = &bus_tvd2_clk.common.hw,
>> + [CLK_BUS_TVD3] = &bus_tvd3_clk.common.hw,
>> + [CLK_BUS_TVD_TOP] = &bus_tvd_top_clk.common.hw,
>> + [CLK_BUS_TCON0] = &bus_tcon0_clk.common.hw,
>> + [CLK_BUS_TCON1] = &bus_tcon1_clk.common.hw,
>> + [CLK_BUS_TVE0_TCON] = &bus_tve0_tcon_clk.common.hw,
>> + [CLK_BUS_TVE1_TCON] = &bus_tve1_tcon_clk.common.hw,
>> + [CLK_BUS_TCON_TOP] = &bus_tcon_top_clk.common.hw,
>> + [CLK_BUS_CODEC] = &bus_codec_clk.common.hw,
>> + [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
>> + [CLK_BUS_AC97] = &bus_ac97_clk.common.hw,
>> + [CLK_BUS_PIO] = &bus_pio_clk.common.hw,
>> + [CLK_BUS_IR0] = &bus_ir0_clk.common.hw,
>> + [CLK_BUS_IR1] = &bus_ir1_clk.common.hw,
>> + [CLK_BUS_THS] = &bus_ths_clk.common.hw,
>> + [CLK_BUS_KEYPAD] = &bus_keypad_clk.common.hw,
>> + [CLK_BUS_I2S0] = &bus_i2s0_clk.common.hw,
>> + [CLK_BUS_I2S1] = &bus_i2s1_clk.common.hw,
>> + [CLK_BUS_I2S2] = &bus_i2s2_clk.common.hw,
>> + [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
>> + [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
>> + [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
>> + [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
>> + [CLK_BUS_CAN] = &bus_can_clk.common.hw,
>> + [CLK_BUS_SCR] = &bus_scr_clk.common.hw,
>> + [CLK_BUS_PS20] = &bus_ps20_clk.common.hw,
>> + [CLK_BUS_PS21] = &bus_ps21_clk.common.hw,
>> + [CLK_BUS_I2C4] = &bus_i2c4_clk.common.hw,
>> + [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
>> + [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
>> + [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
>> + [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
>> + [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
>> + [CLK_BUS_UART5] = &bus_uart5_clk.common.hw,
>> + [CLK_BUS_UART6] = &bus_uart6_clk.common.hw,
>> + [CLK_BUS_UART7] = &bus_uart7_clk.common.hw,
>> + [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
>> + [CLK_THS] = &ths_clk.common.hw,
>> + [CLK_NAND] = &nand_clk.common.hw,
>> + [CLK_MMC0] = &mmc0_clk.common.hw,
>> + [CLK_MMC1] = &mmc1_clk.common.hw,
>> + [CLK_MMC2] = &mmc2_clk.common.hw,
>> + [CLK_MMC3] = &mmc3_clk.common.hw,
>> + [CLK_TS] = &ts_clk.common.hw,
>> + [CLK_CE] = &ce_clk.common.hw,
>> + [CLK_SPI0] = &spi0_clk.common.hw,
>> + [CLK_SPI1] = &spi1_clk.common.hw,
>> + [CLK_SPI2] = &spi2_clk.common.hw,
>> + [CLK_SPI3] = &spi3_clk.common.hw,
>> + [CLK_I2S0] = &i2s0_clk.common.hw,
>> + [CLK_I2S1] = &i2s1_clk.common.hw,
>> + [CLK_I2S2] = &i2s2_clk.common.hw,
>> + [CLK_AC97] = &ac97_clk.common.hw,
>> + [CLK_SPDIF] = &spdif_clk.common.hw,
>> + [CLK_KEYPAD] = &keypad_clk.common.hw,
>> + [CLK_SATA] = &sata_clk.common.hw,
>> + [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
>> + [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
>> + [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
>> + [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
>> + [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
>> + [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
>> + [CLK_USB_OHCI0_12M] = &usb_ohci0_12m_clk.common.hw,
>> + [CLK_USB_OHCI1_12M] = &usb_ohci1_12m_clk.common.hw,
>> + [CLK_USB_OHCI2_12M] = &usb_ohci2_12m_clk.common.hw,
>> + [CLK_IR0] = &ir0_clk.common.hw,
>> + [CLK_IR1] = &ir1_clk.common.hw,
>> + [CLK_DRAM] = &dram_clk.common.hw,
>> + [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
>> + [CLK_DRAM_CSI0] = &dram_csi0_clk.common.hw,
>> + [CLK_DRAM_CSI1] = &dram_csi1_clk.common.hw,
>> + [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
>> + [CLK_DRAM_TVD] = &dram_tvd_clk.common.hw,
>> + [CLK_DRAM_DE_MP] = &dram_de_mp_clk.common.hw,
>> + [CLK_DRAM_DEINTERLACE] = &dram_deinterlace_clk.common.hw,
>> + [CLK_DE] = &de_clk.common.hw,
>> + [CLK_DE_MP] = &de_mp_clk.common.hw,
>> + [CLK_TCON0] = &tcon0_clk.common.hw,
>> + [CLK_TCON1] = &tcon1_clk.common.hw,
>> + [CLK_TCON_TVE0] = &tcon_tve0_clk.common.hw,
>> + [CLK_TCON_TVE1] = &tcon_tve1_clk.common.hw,
>> + [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
>> + [CLK_CSI1_MCLK] = &csi1_mclk_clk.common.hw,
>> + [CLK_CSI_SCLK] = &csi_sclk_clk.common.hw,
>> + [CLK_CSI0_MCLK] = &csi0_mclk_clk.common.hw,
>> + [CLK_VE] = &ve_clk.common.hw,
>> + [CLK_ADDA] = &adda_clk.common.hw,
>> + [CLK_ADDA_4X] = &adda_4x_clk.common.hw,
>> + [CLK_AVS] = &avs_clk.common.hw,
>> + [CLK_HDMI] = &hdmi_clk.common.hw,
>> + [CLK_HDMI_SLOW] = &hdmi_slow_clk.common.hw,
>> + [CLK_MBUS] = &mbus_clk.common.hw,
>> + [CLK_MIPI_DSI] = &mipi_dsi_clk.common.hw,
>> + [CLK_TVE0] = &tve0_clk.common.hw,
>> + [CLK_TVE1] = &tve1_clk.common.hw,
>> + [CLK_TVD0] = &tvd0_clk.common.hw,
>> + [CLK_TVD1] = &tvd1_clk.common.hw,
>> + [CLK_TVD2] = &tvd2_clk.common.hw,
>> + [CLK_TVD3] = &tvd3_clk.common.hw,
>> + [CLK_GPU] = &gpu_clk.common.hw,
>> + [CLK_OUTA] = &outa_clk.common.hw,
>> + [CLK_OUTB] = &outb_clk.common.hw,
>> + },
>> + .num = CLK_NUMBER,
>> +};
>> +
>> +static struct ccu_reset_map sun8i_r40_ccu_resets[] = {
>> + [RST_USB_PHY0] = { 0x0cc, BIT(0) },
>> + [RST_USB_PHY1] = { 0x0cc, BIT(1) },
>> + [RST_USB_PHY2] = { 0x0cc, BIT(2) },
>> +
>
> There is also a reset control for the DRAM controller at bit 31
> of register 0xf4.
>
>> + [RST_MBUS] = { 0x0fc, BIT(31) },
>> +
>> + [RST_BUS_MIPI_DSI] = { 0x2c0, BIT(1) },
>> + [RST_BUS_CE] = { 0x2c0, BIT(5) },
>> + [RST_BUS_DMA] = { 0x2c0, BIT(6) },
>> + [RST_BUS_MMC0] = { 0x2c0, BIT(8) },
>> + [RST_BUS_MMC1] = { 0x2c0, BIT(9) },
>> + [RST_BUS_MMC2] = { 0x2c0, BIT(10) },
>> + [RST_BUS_MMC3] = { 0x2c0, BIT(11) },
>> + [RST_BUS_NAND] = { 0x2c0, BIT(13) },
>> + [RST_BUS_DRAM] = { 0x2c0, BIT(14) },
>> + [RST_BUS_EMAC] = { 0x2c0, BIT(17) },
>> + [RST_BUS_TS] = { 0x2c0, BIT(18) },
>> + [RST_BUS_HSTIMER] = { 0x2c0, BIT(19) },
>> + [RST_BUS_SPI0] = { 0x2c0, BIT(20) },
>> + [RST_BUS_SPI1] = { 0x2c0, BIT(21) },
>> + [RST_BUS_SPI2] = { 0x2c0, BIT(22) },
>> + [RST_BUS_SPI3] = { 0x2c0, BIT(23) },
>> + [RST_BUS_SATA] = { 0x2c0, BIT(24) },
>> + [RST_BUS_OTG] = { 0x2c0, BIT(25) },
>> + [RST_BUS_EHCI0] = { 0x2c0, BIT(26) },
>> + [RST_BUS_EHCI1] = { 0x2c0, BIT(27) },
>> + [RST_BUS_EHCI2] = { 0x2c0, BIT(28) },
>> + [RST_BUS_OHCI0] = { 0x2c0, BIT(29) },
>> + [RST_BUS_OHCI1] = { 0x2c0, BIT(30) },
>> + [RST_BUS_OHCI2] = { 0x2c0, BIT(31) },
>> +
>> + [RST_BUS_VE] = { 0x2c4, BIT(0) },
>> + [RST_BUS_DE_MP] = { 0x2c4, BIT(2) },
>
> Same thing about the MP's name.
>
>> + [RST_BUS_DEINTERLACE] = { 0x2c4, BIT(5) },
>> + [RST_BUS_CSI0] = { 0x2c4, BIT(8) },
>> + [RST_BUS_CSI1] = { 0x2c4, BIT(9) },
>> + [RST_BUS_HDMI_SLOW] = { 0x2c4, BIT(10) },
>> + [RST_BUS_HDMI] = { 0x2c4, BIT(11) },
>
> Same thing about the HDMI's names.
>
>> + [RST_BUS_DE] = { 0x2c4, BIT(12) },
>> + [RST_BUS_TVE0] = { 0x2c4, BIT(13) },
>> + [RST_BUS_TVE1] = { 0x2c4, BIT(14) },
>> + [RST_BUS_TVE_TOP] = { 0x2c4, BIT(15) },
>> + [RST_BUS_GMAC] = { 0x2c4, BIT(17) },
>> + [RST_BUS_GPU] = { 0x2c4, BIT(20) },
>> + [RST_BUS_TVD0] = { 0x2c4, BIT(21) },
>> + [RST_BUS_TVD1] = { 0x2c4, BIT(22) },
>> + [RST_BUS_TVD2] = { 0x2c4, BIT(23) },
>> + [RST_BUS_TVD3] = { 0x2c4, BIT(24) },
>> + [RST_BUS_TVD_TOP] = { 0x2c4, BIT(25) },
>> + [RST_BUS_TCON0] = { 0x2c4, BIT(26) },
>> + [RST_BUS_TCON1] = { 0x2c4, BIT(27) },
>> + [RST_BUS_TCON_TVE0] = { 0x2c4, BIT(28) },
>> + [RST_BUS_TCON_TVE1] = { 0x2c4, BIT(29) },
>
> Same thing about the TCON names.
>
>> + [RST_BUS_TCON_TOP] = { 0x2c4, BIT(30) },
>> + [RST_BUS_DBG] = { 0x2c4, BIT(31) },
>> +
>> + [RST_BUS_LVDS] = { 0x2c8, BIT(0) },
>> +
>> + [RST_BUS_CODEC] = { 0x2d0, BIT(0) },
>> + [RST_BUS_SPDIF] = { 0x2d0, BIT(1) },
>> + [RST_BUS_AC97] = { 0x2d0, BIT(2) },
>> + [RST_BUS_IR0] = { 0x2d0, BIT(6) },
>> + [RST_BUS_IR1] = { 0x2d0, BIT(7) },
>> + [RST_BUS_THS] = { 0x2d0, BIT(8) },
>> + [RST_BUS_KEYPAD] = { 0x2d0, BIT(10) },
>> + [RST_BUS_I2S0] = { 0x2d0, BIT(12) },
>> + [RST_BUS_I2S1] = { 0x2d0, BIT(13) },
>> + [RST_BUS_I2S2] = { 0x2d0, BIT(14) },
>> +
>> + [RST_BUS_I2C0] = { 0x2d8, BIT(0) },
>> + [RST_BUS_I2C1] = { 0x2d8, BIT(1) },
>> + [RST_BUS_I2C2] = { 0x2d8, BIT(2) },
>> + [RST_BUS_I2C3] = { 0x2d8, BIT(3) },
>> + [RST_BUS_CAN] = { 0x2d8, BIT(4) },
>
> Please add a note for CAN like you did with the bus gate.
>
>> + [RST_BUS_SCR] = { 0x2d8, BIT(5) },
>> + [RST_BUS_PS20] = { 0x2d8, BIT(6) },
>> + [RST_BUS_PS21] = { 0x2d8, BIT(7) },
>> + [RST_BUS_I2C4] = { 0x2d8, BIT(15) },
>> + [RST_BUS_UART0] = { 0x2d8, BIT(16) },
>> + [RST_BUS_UART1] = { 0x2d8, BIT(17) },
>> + [RST_BUS_UART2] = { 0x2d8, BIT(18) },
>> + [RST_BUS_UART3] = { 0x2d8, BIT(19) },
>> + [RST_BUS_UART4] = { 0x2d8, BIT(20) },
>> + [RST_BUS_UART5] = { 0x2d8, BIT(21) },
>> + [RST_BUS_UART6] = { 0x2d8, BIT(22) },
>> + [RST_BUS_UART7] = { 0x2d8, BIT(23) },
>> +};
>> +
>> +static const struct sunxi_ccu_desc sun8i_r40_ccu_desc = {
>> + .ccu_clks = sun8i_r40_ccu_clks,
>> + .num_ccu_clks = ARRAY_SIZE(sun8i_r40_ccu_clks),
>> +
>> + .hw_clks = &sun8i_r40_hw_clks,
>> +
>> + .resets = sun8i_r40_ccu_resets,
>> + .num_resets = ARRAY_SIZE(sun8i_r40_ccu_resets),
>> +};
>> +
>> +static struct ccu_mux_nb sun8i_r40_cpu_nb = {
>> + .common = &cpu_clk.common,
>> + .cm = &cpu_clk.mux,
>> + .delay_us = 1, /* > 8 clock cycles at 24 MHz */
>> + .bypass_index = 1, /* index of 24 MHz oscillator */
>> +};
>> +
>> +static void __init sun8i_r40_ccu_setup(struct device_node *node)
>> +{
>> + void __iomem *reg;
>> + u32 val;
>> +
>> + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
>> + if (IS_ERR(reg)) {
>> + pr_err("%s: Could not map the clock registers\n",
>> + of_node_full_name(node));
>> + return;
>> + }
>> +
>> + /* Force the PLL-Audio-1x divider to 4 */
>> + val = readl(reg + SUN8I_R40_PLL_AUDIO_REG);
>> + val &= ~GENMASK(19, 16);
>> + writel(val | (3 << 16), reg + SUN8I_R40_PLL_AUDIO_REG);
>> +
>> + sunxi_ccu_probe(node, reg, &sun8i_r40_ccu_desc);
>> +
>> + ccu_mux_notifier_register(pll_cpu_clk.common.hw.clk,
>> + &sun8i_r40_cpu_nb);
>> +}
>> +CLK_OF_DECLARE(sun8i_r40_ccu, "allwinner,sun8i-r40-ccu",
>> + sun8i_r40_ccu_setup);
>> diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
>> b/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
>> new file mode 100644
>> index 000000000000..be30eb662d78
>> --- /dev/null
>> +++ b/drivers/clk/sunxi-ng/ccu-sun8i-r40.h
>> @@ -0,0 +1,68 @@
>> +/*
>> + * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
>> + *
>> + * This program is free software; you can redistribute it and/or
>> modify
>> + * it under the terms of the GNU General Public License as published
>> by
>> + * the Free Software Foundation; either version 2 of the License, or
>> + * (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#ifndef _CCU_SUN8I_R40_H_
>> +#define _CCU_SUN8I_R40_H_
>> +
>> +#include <dt-bindings/clock/sun8i-r40-ccu.h>
>> +#include <dt-bindings/reset/sun8i-r40-ccu.h>
>> +
>> +#define CLK_OSC24M_2X 0
>
> As mentioned, please drop this one.
>
>> +#define CLK_OSC24M_32K 1
>> +#define CLK_PLL_CPU 2
>> +#define CLK_PLL_AUDIO_BASE 3
>> +#define CLK_PLL_AUDIO 4
>> +#define CLK_PLL_AUDIO_2X 5
>> +#define CLK_PLL_AUDIO_4X 6
>> +#define CLK_PLL_AUDIO_8X 7
>> +#define CLK_PLL_VIDEO0 8
>> +#define CLK_PLL_VIDEO0_2X 9
>> +#define CLK_PLL_VE 10
>> +#define CLK_PLL_DDR0 11
>> +#define CLK_PLL_PERIPH0 12
>> +#define CLK_PLL_PERIPH0_2X 13
>> +#define CLK_PLL_PERIPH1 14
>> +#define CLK_PLL_PERIPH1_2X 15
>> +#define CLK_PLL_VIDEO1 16
>> +#define CLK_PLL_VIDEO1_2X 17
>> +#define CLK_PLL_SATA 18
>> +#define CLK_PLL_GPU 19
>> +#define CLK_PLL_MIPI 20
>> +#define CLK_PLL_DE 21
>> +#define CLK_PLL_DDR1 22
>> +
>> +/* The CPU clock is exported */
>> +
>> +#define CLK_AXI 24
>> +#define CLK_AHB1 25
>> +#define CLK_APB1 26
>> +#define CLK_APB2 27
>> +
>> +/* All the bus gates are exported */
>> +
>> +/* The first bunch of module clocks are exported */
>> +
>> +#define CLK_DRAM 134
>> +
>> +/* All the DRAM gates are exported */
>> +
>> +/* Some more module clocks are exported */
>> +
>> +#define CLK_MBUS 158
>> +
>> +/* Another bunch of module clocks are exported */
>> +
>> +#define CLK_NUMBER (CLK_OUTB + 1)
>> +
>> +#endif /* _CCU_SUN8I_R40_H_ */
>> diff --git a/include/dt-bindings/clock/sun8i-r40-ccu.h
>> b/include/dt-bindings/clock/sun8i-r40-ccu.h
>> new file mode 100644
>> index 000000000000..a907d841496d
>> --- /dev/null
>> +++ b/include/dt-bindings/clock/sun8i-r40-ccu.h
>> @@ -0,0 +1,191 @@
>> +/*
>> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the
>> Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
>> KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
>> WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +#ifndef _DT_BINDINGS_CLK_SUN8I_R40_H_
>> +#define _DT_BINDINGS_CLK_SUN8I_R40_H_
>> +
>> +#define CLK_CPU 23
>> +
>> +#define CLK_BUS_MIPI_DSI 28
>> +#define CLK_BUS_CE 29
>> +#define CLK_BUS_DMA 30
>> +#define CLK_BUS_MMC0 31
>> +#define CLK_BUS_MMC1 32
>> +#define CLK_BUS_MMC2 33
>> +#define CLK_BUS_MMC3 34
>> +#define CLK_BUS_NAND 35
>> +#define CLK_BUS_DRAM 36
>> +#define CLK_BUS_EMAC 37
>> +#define CLK_BUS_TS 38
>> +#define CLK_BUS_HSTIMER 39
>> +#define CLK_BUS_SPI0 40
>> +#define CLK_BUS_SPI1 41
>> +#define CLK_BUS_SPI2 42
>> +#define CLK_BUS_SPI3 43
>> +#define CLK_BUS_SATA 44
>> +#define CLK_BUS_OTG 45
>> +#define CLK_BUS_EHCI0 46
>> +#define CLK_BUS_EHCI1 47
>> +#define CLK_BUS_EHCI2 48
>> +#define CLK_BUS_OHCI0 49
>> +#define CLK_BUS_OHCI1 50
>> +#define CLK_BUS_OHCI2 51
>> +#define CLK_BUS_VE 52
>> +#define CLK_BUS_DE_MP 53
>
> MP name...
>
>> +#define CLK_BUS_DEINTERLACE 54
>> +#define CLK_BUS_CSI0 55
>> +#define CLK_BUS_CSI1 56
>> +#define CLK_BUS_HDMI_SLOW 57
>> +#define CLK_BUS_HDMI 58
>
> Names...
>
>> +#define CLK_BUS_DE 59
>> +#define CLK_BUS_TVE0 60
>> +#define CLK_BUS_TVE1 61
>> +#define CLK_BUS_TVE_TOP 62
>> +#define CLK_BUS_GMAC 63
>> +#define CLK_BUS_GPU 64
>> +#define CLK_BUS_TVD0 65
>> +#define CLK_BUS_TVD1 66
>> +#define CLK_BUS_TVD2 67
>> +#define CLK_BUS_TVD3 68
>> +#define CLK_BUS_TVD_TOP 69
>
>> +#define CLK_BUS_TCON0 70
>> +#define CLK_BUS_TCON1 71
>> +#define CLK_BUS_TVE0_TCON 72
>> +#define CLK_BUS_TVE1_TCON 73
>
> Names...
>
>> +#define CLK_BUS_TCON_TOP 74
>> +#define CLK_BUS_CODEC 75
>> +#define CLK_BUS_SPDIF 76
>> +#define CLK_BUS_AC97 77
>> +#define CLK_BUS_PIO 78
>> +#define CLK_BUS_IR0 79
>> +#define CLK_BUS_IR1 80
>> +#define CLK_BUS_THS 81
>> +#define CLK_BUS_KEYPAD 82
>> +#define CLK_BUS_I2S0 83
>> +#define CLK_BUS_I2S1 84
>> +#define CLK_BUS_I2S2 85
>> +#define CLK_BUS_I2C0 86
>> +#define CLK_BUS_I2C1 87
>> +#define CLK_BUS_I2C2 88
>> +#define CLK_BUS_I2C3 89
>> +#define CLK_BUS_CAN 90
>> +#define CLK_BUS_SCR 91
>> +#define CLK_BUS_PS20 92
>> +#define CLK_BUS_PS21 93
>> +#define CLK_BUS_I2C4 94
>> +#define CLK_BUS_UART0 95
>> +#define CLK_BUS_UART1 96
>> +#define CLK_BUS_UART2 97
>> +#define CLK_BUS_UART3 98
>> +#define CLK_BUS_UART4 99
>> +#define CLK_BUS_UART5 100
>> +#define CLK_BUS_UART6 101
>> +#define CLK_BUS_UART7 102
>> +#define CLK_BUS_DBG 103
>> +
>> +#define CLK_THS 104
>> +#define CLK_NAND 105
>> +#define CLK_MMC0 106
>> +#define CLK_MMC1 107
>> +#define CLK_MMC2 108
>> +#define CLK_MMC3 109
>> +#define CLK_TS 110
>> +#define CLK_CE 111
>> +#define CLK_SPI0 112
>> +#define CLK_SPI1 113
>> +#define CLK_SPI2 114
>> +#define CLK_SPI3 115
>> +#define CLK_I2S0 116
>> +#define CLK_I2S1 117
>> +#define CLK_I2S2 118
>> +#define CLK_AC97 119
>> +#define CLK_SPDIF 120
>> +#define CLK_KEYPAD 121
>> +#define CLK_SATA 122
>> +#define CLK_USB_PHY0 123
>> +#define CLK_USB_PHY1 124
>> +#define CLK_USB_PHY2 125
>> +#define CLK_USB_OHCI0 126
>> +#define CLK_USB_OHCI1 127
>> +#define CLK_USB_OHCI2 128
>> +#define CLK_USB_OHCI0_12M 129
>> +#define CLK_USB_OHCI1_12M 130
>> +#define CLK_USB_OHCI2_12M 131
>
> These 3 should not be exported.
>
>> +#define CLK_IR0 132
>> +#define CLK_IR1 133
>> +
>> +#define CLK_DRAM_VE 135
>> +#define CLK_DRAM_CSI0 136
>> +#define CLK_DRAM_CSI1 137
>> +#define CLK_DRAM_TS 138
>> +#define CLK_DRAM_TVD 139
>> +#define CLK_DRAM_DE_MP 140
>
> MP name...
>
>> +#define CLK_DRAM_DEINTERLACE 141
>> +#define CLK_DE 142
>> +#define CLK_DE_MP 143
>
> MP name...
>
>> +#define CLK_TCON0 144
>> +#define CLK_TCON1 145
>> +#define CLK_TCON_TVE0 146
>> +#define CLK_TCON_TVE1 147
>
> Names...
>
>> +#define CLK_DEINTERLACE 148
>> +#define CLK_CSI1_MCLK 149
>> +#define CLK_CSI_SCLK 150
>> +#define CLK_CSI0_MCLK 151
>> +#define CLK_VE 152
>> +#define CLK_ADDA 153
>
>> +#define CLK_ADDA_4X 154
>
> Nonexistent.
>
>> +#define CLK_AVS 155
>> +#define CLK_HDMI 156
>> +#define CLK_HDMI_SLOW 157
>> +
>> +#define CLK_MIPI_DSI 159
>> +#define CLK_TVE0 160
>> +#define CLK_TVE1 161
>> +#define CLK_TVD0 162
>> +#define CLK_TVD1 163
>> +#define CLK_TVD2 164
>> +#define CLK_TVD3 165
>> +#define CLK_GPU 166
>> +#define CLK_OUTA 167
>> +#define CLK_OUTB 168
>> +
>> +#endif /* _DT_BINDINGS_CLK_SUN8I_R40_H_ */
>> diff --git a/include/dt-bindings/reset/sun8i-r40-ccu.h
>> b/include/dt-bindings/reset/sun8i-r40-ccu.h
>> new file mode 100644
>> index 000000000000..a7001f34b0b9
>> --- /dev/null
>> +++ b/include/dt-bindings/reset/sun8i-r40-ccu.h
>
> Name corrections apply to this file as well.
>
> Regards
> ChenYu
>
>> --
>> 2.12.2
>>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-05-29 7:34 ` Chen-Yu Tsai
2017-07-22 3:00 ` icenowy
@ 2017-08-12 4:04 ` icenowy
2017-08-12 4:05 ` Chen-Yu Tsai
1 sibling, 1 reply; 36+ messages in thread
From: icenowy @ 2017-08-12 4:04 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Maxime Ripard, Rob Herring, Linus Walleij, linux-doc,
linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
在 2017-05-29 15:34，Chen-Yu Tsai 写道：
> Hi,
>
> On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
>> Allwinner R40 SoC have a clock controller module in the style of the
>> SoCs beyond sun6i, however, it's more rich and complex.
>>
>> Add support for it.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> ---
>> Changes in v3:
>> - Rebased on current linux-next.
>> Changes in v2:
>> - Fixes according to the SoC's user manual.
>>
>> drivers/clk/sunxi-ng/Kconfig | 10 +
>> drivers/clk/sunxi-ng/Makefile | 1 +
>> drivers/clk/sunxi-ng/ccu-sun8i-r40.c | 1153
>> +++++++++++++++++++++++++++++
>> drivers/clk/sunxi-ng/ccu-sun8i-r40.h | 68 ++
>> include/dt-bindings/clock/sun8i-r40-ccu.h | 191 +++++
>> include/dt-bindings/reset/sun8i-r40-ccu.h | 129 ++++
>> 6 files changed, 1552 insertions(+)
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.c
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.h
>> create mode 100644 include/dt-bindings/clock/sun8i-r40-ccu.h
>> create mode 100644 include/dt-bindings/reset/sun8i-r40-ccu.h
>>
> ...
>> +static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
>> + "osc24M", 0x04c,
>> + 8, 7, /* N */
>
> N has minimum and maximum limits.
These constraints are never implemented in old SoCs.
>> --
>> 2.12.2
>>
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-07-22 3:00 ` icenowy
@ 2017-08-12 4:04 ` Chen-Yu Tsai
2017-08-12 4:51 ` icenowy
0 siblings, 1 reply; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-08-12 4:04 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, devicetree, linux-doc, Linus Walleij, linux-kernel,
linux-gpio, Rob Herring, Maxime Ripard, linux-clk,
linux-arm-kernel
On Sat, Jul 22, 2017 at 11:00 AM, <icenowy@aosc.io> wrote:
> 在 2017-05-29 15:34，Chen-Yu Tsai 写道：
>>
>> Hi,
>>
>> On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
[...]
>>> +
>>> +/*
>>> + * For the special bit in gate part, please see the BSP source code at
>>> + *
>>> https://github.com/BPI-SINOVOIP/BPI-M2U-bsp/blob/master/linux-sunxi/drivers/clk/sunxi/clk-sun8iw11.c#L665
>>> + */
>>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_sata_clk, "pll-sata",
>>> + "osc24M", 0x034,
>>> + 8, 5, /* N */
>>> + 4, 2, /* K */
>>> + 0, 2, /* M */
>>> + BIT(31) | BIT(14), /* gate */
>>> + BIT(28), /* lock */
>>> + 0);
>>
>>
>> I think this is a somewhat simplified approach. From what I understand
>> of the user manual, the SATA clock path look like:
>>
>>
>> [ PLL-PERIPH0-SATA ] -\
>> mux @ 0x34 bit 30 --- gate @ 0x34 bit 14 --- ...
>> [ PLL-SATA ] ---------/
>>
>> ... from above ... ------\
>> mux @ 0xc8 bit 24 --- gate @ 0xc8 bit 31
>> [ external oscillator ] -/
>>
>> If you choose to simplify the implementation, please include a detailed
>> note as to why you chose to do so, and the validity of the simplification.
>
>
> I think it can be fully implemented...
>
> But how should I call the internal clock controlled by the mux @ 0x34 bit
> 30?
sata-pll-mux?
ChenYu
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-08-12 4:04 ` icenowy
@ 2017-08-12 4:05 ` Chen-Yu Tsai
0 siblings, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-08-12 4:05 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, Maxime Ripard, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sat, Aug 12, 2017 at 12:04 PM, <icenowy@aosc.io> wrote:
> 在 2017-05-29 15:34，Chen-Yu Tsai 写道：
>>
>> Hi,
>>
>> On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
>>>
>>> Allwinner R40 SoC have a clock controller module in the style of the
>>> SoCs beyond sun6i, however, it's more rich and complex.
>>>
>>> Add support for it.
>>>
>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>>> ---
>>> Changes in v3:
>>> - Rebased on current linux-next.
>>> Changes in v2:
>>> - Fixes according to the SoC's user manual.
>>>
>>> drivers/clk/sunxi-ng/Kconfig | 10 +
>>> drivers/clk/sunxi-ng/Makefile | 1 +
>>> drivers/clk/sunxi-ng/ccu-sun8i-r40.c | 1153
>>> +++++++++++++++++++++++++++++
>>> drivers/clk/sunxi-ng/ccu-sun8i-r40.h | 68 ++
>>> include/dt-bindings/clock/sun8i-r40-ccu.h | 191 +++++
>>> include/dt-bindings/reset/sun8i-r40-ccu.h | 129 ++++
>>> 6 files changed, 1552 insertions(+)
>>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.c
>>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-r40.h
>>> create mode 100644 include/dt-bindings/clock/sun8i-r40-ccu.h
>>> create mode 100644 include/dt-bindings/reset/sun8i-r40-ccu.h
>>>
>> ...
>>>
>>> +static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
>>> + "osc24M", 0x04c,
>>> + 8, 7, /* N */
>>
>>
>> N has minimum and maximum limits.
>
>
> These constraints are never implemented in old SoCs.
Then we should implement them if we find that they are
missing.
ChenYu
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-08-12 4:04 ` Chen-Yu Tsai
@ 2017-08-12 4:51 ` icenowy
2017-08-12 5:16 ` Chen-Yu Tsai
0 siblings, 1 reply; 36+ messages in thread
From: icenowy @ 2017-08-12 4:51 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: devicetree, linux-doc, Linus Walleij, linux-kernel, linux-gpio,
Rob Herring, Maxime Ripard, linux-clk, linux-arm-kernel
在 2017-08-12 12:04，Chen-Yu Tsai 写道：
> On Sat, Jul 22, 2017 at 11:00 AM, <icenowy@aosc.io> wrote:
>> 在 2017-05-29 15:34，Chen-Yu Tsai 写道：
>>>
>>> Hi,
>>>
>>> On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
>
> [...]
>
>>>> +
>>>> +/*
>>>> + * For the special bit in gate part, please see the BSP source code
>>>> at
>>>> + *
>>>> https://github.com/BPI-SINOVOIP/BPI-M2U-bsp/blob/master/linux-sunxi/drivers/clk/sunxi/clk-sun8iw11.c#L665
>>>> + */
>>>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_sata_clk, "pll-sata",
>>>> + "osc24M", 0x034,
>>>> + 8, 5, /* N */
>>>> + 4, 2, /* K */
>>>> + 0, 2, /* M */
>>>> + BIT(31) | BIT(14), /* gate */
>>>> + BIT(28), /* lock */
>>>> + 0);
>>>
>>>
>>> I think this is a somewhat simplified approach. From what I
>>> understand
>>> of the user manual, the SATA clock path look like:
>>>
>>>
>>> [ PLL-PERIPH0-SATA ] -\
>>> mux @ 0x34 bit 30 --- gate @ 0x34 bit 14 ---
>>> ...
>>> [ PLL-SATA ] ---------/
>>>
>>> ... from above ... ------\
>>> mux @ 0xc8 bit 24 --- gate @ 0xc8 bit 31
>>> [ external oscillator ] -/
>>>
>>> If you choose to simplify the implementation, please include a
>>> detailed
>>> note as to why you chose to do so, and the validity of the
>>> simplification.
>>
>>
>> I think it can be fully implemented...
>>
>> But how should I call the internal clock controlled by the mux @ 0x34
>> bit
>> 30?
>
> sata-pll-mux?
I choose to call it pll-sata-out, as the mux @ 0x34 bit 30 is called
"PLL_OUTPUT_SEL".
>
> ChenYu
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC
2017-08-12 4:51 ` icenowy
@ 2017-08-12 5:16 ` Chen-Yu Tsai
0 siblings, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-08-12 5:16 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Chen-Yu Tsai, devicetree, linux-doc, Linus Walleij, linux-kernel,
linux-gpio, Rob Herring, Maxime Ripard, linux-clk,
linux-arm-kernel
On Sat, Aug 12, 2017 at 12:51 PM, <icenowy@aosc.io> wrote:
> 在 2017-08-12 12:04，Chen-Yu Tsai 写道：
>>
>> On Sat, Jul 22, 2017 at 11:00 AM, <icenowy@aosc.io> wrote:
>>>
>>> 在 2017-05-29 15:34，Chen-Yu Tsai 写道：
>>>>
>>>>
>>>> Hi,
>>>>
>>>> On Sat, May 27, 2017 at 06:23:06PM +0800, Icenowy Zheng wrote:
>>
>>
>> [...]
>>
>>>>> +
>>>>> +/*
>>>>> + * For the special bit in gate part, please see the BSP source code at
>>>>> + *
>>>>>
>>>>> https://github.com/BPI-SINOVOIP/BPI-M2U-bsp/blob/master/linux-sunxi/drivers/clk/sunxi/clk-sun8iw11.c#L665
>>>>> + */
>>>>> +static SUNXI_CCU_NKM_WITH_GATE_LOCK(pll_sata_clk, "pll-sata",
>>>>> + "osc24M", 0x034,
>>>>> + 8, 5, /* N */
>>>>> + 4, 2, /* K */
>>>>> + 0, 2, /* M */
>>>>> + BIT(31) | BIT(14), /* gate */
>>>>> + BIT(28), /* lock */
>>>>> + 0);
>>>>
>>>>
>>>>
>>>> I think this is a somewhat simplified approach. From what I understand
>>>> of the user manual, the SATA clock path look like:
>>>>
>>>>
>>>> [ PLL-PERIPH0-SATA ] -\
>>>> mux @ 0x34 bit 30 --- gate @ 0x34 bit 14 --- ...
>>>> [ PLL-SATA ] ---------/
>>>>
>>>> ... from above ... ------\
>>>> mux @ 0xc8 bit 24 --- gate @ 0xc8 bit 31
>>>> [ external oscillator ] -/
>>>>
>>>> If you choose to simplify the implementation, please include a detailed
>>>> note as to why you chose to do so, and the validity of the
>>>> simplification.
>>>
>>>
>>>
>>> I think it can be fully implemented...
>>>
>>> But how should I call the internal clock controlled by the mux @ 0x34 bit
>>> 30?
>>
>>
>> sata-pll-mux?
>
>
> I choose to call it pll-sata-out, as the mux @ 0x34 bit 30 is called
> "PLL_OUTPUT_SEL".
Cool. Note that the clock names don't really matter for end users.
The only place this is visible is debugfs, or if some driver prints
it out for debug messages. So the only real requirement is that the
name makes some sense to any developers using it, in a way that they
can spot if they are using it wrong, like accidentally using a clock
for another module, and being able to roughly match it up to the
datasheet.
ChenYu
^ permalink raw reply [flat|nested] 36+ messages in thread
* Re: [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU
2017-05-28 15:09 ` Chen-Yu Tsai
@ 2017-08-19 8:17 ` Chen-Yu Tsai
0 siblings, 0 replies; 36+ messages in thread
From: Chen-Yu Tsai @ 2017-08-19 8:17 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Icenowy Zheng, Maxime Ripard, Rob Herring, Linus Walleij,
linux-doc, linux-arm-kernel, linux-kernel, devicetree, linux-clk,
linux-gpio
On Sun, May 28, 2017 at 11:09 PM, Chen-Yu Tsai <wens@csie.org> wrote:
> On Sat, May 27, 2017 at 6:23 PM, Icenowy Zheng <icenowy@aosc.io> wrote:
>> Allwinner R40 has a clock controlling unit like the ones on other
>> Allwinner SoCs after sun6i, and can also use a CCU-based driver.
>>
>> Add a compatible string for it.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>> Acked-by: Rob Herring <robh@kernel.org>
>
> Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Fixed the conflict and applied for 4.14. Next time please include this when you
send the driver patches.
ChenYu
^ permalink raw reply [flat|nested] 36+ messages in thread
end of thread, other threads:[~2017-08-19 8:17 UTC | newest]
Thread overview: 36+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-05-27 10:22 [PATCH v3 00/10] Initial Allwinner R40 support Icenowy Zheng
2017-05-27 10:22 ` [PATCH v3 01/10] arm: sunxi: add support for R40 SoC Icenowy Zheng
2017-05-28 14:57 ` Chen-Yu Tsai
2017-05-31 19:42 ` Rob Herring
2017-05-27 10:23 ` [PATCH v3 02/10] pinctrl: sunxi: Add SoC ID definitions for A10, A20 and R40 SoCs Icenowy Zheng
2017-05-28 14:58 ` Chen-Yu Tsai
2017-05-29 16:33 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 03/10] pinctrl: sunxi: add A20 support to A10 driver Icenowy Zheng
2017-05-28 15:06 ` Chen-Yu Tsai
2017-05-29 16:35 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 04/10] pinctrl: sunxi: drop dedicated A20 driver Icenowy Zheng
2017-05-28 15:08 ` Chen-Yu Tsai
2017-05-29 16:39 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 05/10] dt-bindings: add compatible string for Allwinner R40 pinctrl Icenowy Zheng
2017-05-28 15:09 ` Chen-Yu Tsai
2017-05-29 16:40 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 06/10] pinctrl: sunxi: add support of R40 to A10 pinctrl driver Icenowy Zheng
2017-05-29 13:11 ` Chen-Yu Tsai
2017-05-29 13:19 ` icenowy
2017-05-29 13:25 ` Chen-Yu Tsai
2017-05-29 16:43 ` Linus Walleij
2017-05-27 10:23 ` [PATCH v3 07/10] dt-bindings: add compatible string for Allwinner R40 CCU Icenowy Zheng
2017-05-28 15:09 ` Chen-Yu Tsai
2017-08-19 8:17 ` Chen-Yu Tsai
2017-05-27 10:23 ` [PATCH v3 08/10] clk: sunxi-ng: support R40 SoC Icenowy Zheng
2017-05-29 7:34 ` Chen-Yu Tsai
2017-07-22 3:00 ` icenowy
2017-08-12 4:04 ` Chen-Yu Tsai
2017-08-12 4:51 ` icenowy
2017-08-12 5:16 ` Chen-Yu Tsai
2017-08-12 4:04 ` icenowy
2017-08-12 4:05 ` Chen-Yu Tsai
2017-05-27 10:23 ` [PATCH v3 09/10] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40 Icenowy Zheng
2017-05-29 8:15 ` Chen-Yu Tsai
2017-05-27 10:23 ` [PATCH v3 10/10] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra Icenowy Zheng
2017-05-29 8:59 ` Chen-Yu Tsai
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).