[PATCH] net: gianfar: add ethtool eee support

[PATCH] net: gianfar: add ethtool eee support

[Yangbo Lu]

From: Shaohui Xie <Shaohui.Xie@nxp.com>

Gianfar does not support EEE, but it can connect to a PHY which supports
EEE and the PHY advertises EEE by default, and its link partner also
advertises EEE, so the PHY enters low power mode when traffic rate is low,
which causes packet loss if an application's traffic rate is low. This
patch provides .get_eee and .set_eee so that to disable the EEE
advertisement via ethtool if needed, other EEE features are not supported.

Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Yangbo Lu <Yangbo.lu@nxp.com>
---
 drivers/net/ethernet/freescale/gianfar_ethtool.c | 28 ++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/drivers/net/ethernet/freescale/gianfar_ethtool.c b/drivers/net/ethernet/freescale/gianfar_ethtool.c
index 56588f2e1d91..8953650b36f3 100644
--- a/drivers/net/ethernet/freescale/gianfar_ethtool.c
+++ b/drivers/net/ethernet/freescale/gianfar_ethtool.c
@@ -184,6 +184,32 @@ static void gfar_gdrvinfo(struct net_device *dev,
 	strlcpy(drvinfo->bus_info, "N/A", sizeof(drvinfo->bus_info));
 }
 
+static int gfar_get_eee(struct net_device *dev, struct ethtool_eee *et_eee)
+{
+	struct phy_device *phydev = dev->phydev;
+
+	if (!phydev)
+		return -ENODEV;
+
+	return phy_ethtool_get_eee(phydev, et_eee);
+}
+
+static int gfar_set_eee(struct net_device *dev, struct ethtool_eee *et_eee)
+{
+	struct phy_device *phydev = dev->phydev;
+
+	if (!phydev)
+		return -ENODEV;
+
+	if (et_eee->eee_enabled ||
+	    et_eee->tx_lpi_enabled ||
+	    et_eee->tx_lpi_timer) {
+		return -EOPNOTSUPP;
+	}
+
+	return phy_ethtool_set_eee(phydev, et_eee);
+}
+
 /* Return the length of the register structure */
 static int gfar_reglen(struct net_device *dev)
 {
@@ -1535,6 +1561,8 @@ static int gfar_get_ts_info(struct net_device *dev,
 }
 
 const struct ethtool_ops gfar_ethtool_ops = {
+	.get_eee = gfar_get_eee,
+	.set_eee = gfar_set_eee,
 	.get_drvinfo = gfar_gdrvinfo,
 	.get_regs_len = gfar_reglen,
 	.get_regs = gfar_get_regs,
-- 
2.14.1

Re: [PATCH] net: gianfar: add ethtool eee support

[Andrew Lunn]

On Tue, Nov 28, 2017 at 02:29:01PM +0800, Yangbo Lu wrote:
> From: Shaohui Xie <Shaohui.Xie@nxp.com>
> 
> Gianfar does not support EEE, but it can connect to a PHY which supports
> EEE and the PHY advertises EEE by default, and its link partner also
> advertises EEE, so the PHY enters low power mode when traffic rate is low,
> which causes packet loss if an application's traffic rate is low. This
> patch provides .get_eee and .set_eee so that to disable the EEE
> advertisement via ethtool if needed, other EEE features are not supported.

Hi Yangbo

This patch is good, as far as it goes. However, as you said, some PHYs
advertise EEE by default. So i think it would be good to add a call to
phy_ethtool_set_eee() to disable advertisement, e.g. in init_phy().

Thanks
	      Andrew