* [PATCH v2 1/5] arm: zynq: Add Xilinx cc108 board
2018-02-23 15:00 [PATCH v2 0/5] arm: zynq: Adding new Xilinx boards Michal Simek
@ 2018-02-23 15:00 ` Michal Simek
2018-03-02 18:13 ` Rob Herring
2018-02-23 15:00 ` [PATCH v2 2/5] arm: zynq: Add support for Xilinx zc770 xm010 dc1 board Michal Simek
` (3 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-02-23 15:00 UTC (permalink / raw)
To: devicetree
Cc: monstr, Steffen Trumtrar, linux-kernel, Peter Crosthwaite,
Rob Herring, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
The board contains 7z010 with 512MB memory, ethernet, qspi, uart, usbs
and sd. But board is not supporting booting from sd card.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 5 ++
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-cc108.dts | 75 ++++++++++++++++++++++++
3 files changed, 81 insertions(+)
create mode 100644 arch/arm/boot/dts/zynq-cc108.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 549e70a022cb..425c74fcc560 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -6,6 +6,11 @@ shall have the following properties.
Required root node properties:
- compatible = "xlnx,zynq-7000";
+Additional compatible strings:
+
+- Xilinx internal board cc108
+ "xlnx,zynq-cc108"
+
---------------------------------------------------------------
Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..c6810e84d4d7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1062,6 +1062,7 @@ dtb-$(CONFIG_ARCH_VT8500) += \
wm8750-apc8750.dtb \
wm8850-w70v2.dtb
dtb-$(CONFIG_ARCH_ZYNQ) += \
+ zynq-cc108.dtb \
zynq-microzed.dtb \
zynq-parallella.dtb \
zynq-zc702.dtb \
diff --git a/arch/arm/boot/dts/zynq-cc108.dts b/arch/arm/boot/dts/zynq-cc108.dts
new file mode 100644
index 000000000000..1a0f631c1d8d
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-cc108.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx CC108 board DTS
+ *
+ * (C) Copyright 2007-2018 Xilinx, Inc.
+ * (C) Copyright 2007-2013 Michal Simek
+ * (C) Copyright 2007-2012 PetaLogix Qld Pty Ltd
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ */
+/dts-v1/;
+/include/ "zynq-7000.dtsi"
+
+/ {
+ compatible = "xlnx,zynq-cc108", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
+
+ aliases {
+ ethernet0 = &gem0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x20000000>;
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
+ usb_phy1: phy1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+};
+
+&sdhci1 {
+ status = "okay";
+ broken-cd ;
+ wp-inverted ;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy1>;
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v2 1/5] arm: zynq: Add Xilinx cc108 board
2018-02-23 15:00 ` [PATCH v2 1/5] arm: zynq: Add Xilinx cc108 board Michal Simek
@ 2018-03-02 18:13 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-02 18:13 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Steffen Trumtrar, linux-kernel,
Peter Crosthwaite, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
On Fri, Feb 23, 2018 at 04:00:19PM +0100, Michal Simek wrote:
> The board contains 7z010 with 512MB memory, ethernet, qspi, uart, usbs
> and sd. But board is not supporting booting from sd card.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v2:
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 5 ++
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/zynq-cc108.dts | 75 ++++++++++++++++++++++++
> 3 files changed, 81 insertions(+)
> create mode 100644 arch/arm/boot/dts/zynq-cc108.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 2/5] arm: zynq: Add support for Xilinx zc770 xm010 dc1 board
2018-02-23 15:00 [PATCH v2 0/5] arm: zynq: Adding new Xilinx boards Michal Simek
2018-02-23 15:00 ` [PATCH v2 1/5] arm: zynq: Add Xilinx cc108 board Michal Simek
@ 2018-02-23 15:00 ` Michal Simek
2018-03-02 18:50 ` Rob Herring
2018-02-23 15:00 ` [PATCH v2 3/5] arm: zynq: Add support for Xilinx zc770 xm011 dc2 board Michal Simek
` (2 subsequent siblings)
4 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-02-23 15:00 UTC (permalink / raw)
To: devicetree
Cc: monstr, Steffen Trumtrar, linux-kernel, Peter Crosthwaite,
Rob Herring, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-zc770-xm010.dts | 92 ++++++++++++++++++++++++
3 files changed, 96 insertions(+)
create mode 100644 arch/arm/boot/dts/zynq-zc770-xm010.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 425c74fcc560..019e69037d42 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -11,6 +11,9 @@ Additional compatible strings:
- Xilinx internal board cc108
"xlnx,zynq-cc108"
+- Xilinx internal board zc770 with different FMC cards
+ "xlnx,zynq-zc770-xm010"
+
---------------------------------------------------------------
Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c6810e84d4d7..be9ffae2a1ec 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1067,6 +1067,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-parallella.dtb \
zynq-zc702.dtb \
zynq-zc706.dtb \
+ zynq-zc770-xm010.dtb \
zynq-zed.dtb \
zynq-zybo.dtb
dtb-$(CONFIG_MACH_ARMADA_370) += \
diff --git a/arch/arm/boot/dts/zynq-zc770-xm010.dts b/arch/arm/boot/dts/zynq-zc770-xm010.dts
new file mode 100644
index 000000000000..b1cfb4ede434
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-zc770-xm010.dts
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ZC770 XM010 board DTS
+ *
+ * Copyright (C) 2013-2018 Xilinx, Inc.
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ compatible = "xlnx,zynq-zc770-xm010", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
+
+ aliases {
+ ethernet0 = &gem0;
+ i2c0 = &i2c0;
+ serial0 = &uart1;
+ spi1 = &spi1;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x40000000>;
+ };
+
+ usb_phy0: phy0 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&can0 {
+ status = "okay";
+};
+
+&gem0 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@7 {
+ reg = <7>;
+ device_type = "ethernet-phy";
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ };
+
+};
+
+&sdhci0 {
+ status = "okay";
+};
+
+&spi1 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+ flash@0 {
+ compatible = "sst25wf080", "jedec,spi-nor";
+ reg = <1>;
+ spi-max-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@test {
+ label = "spi-flash";
+ reg = <0x0 0x100000>;
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy0>;
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v2 2/5] arm: zynq: Add support for Xilinx zc770 xm010 dc1 board
2018-02-23 15:00 ` [PATCH v2 2/5] arm: zynq: Add support for Xilinx zc770 xm010 dc1 board Michal Simek
@ 2018-03-02 18:50 ` Rob Herring
2018-03-02 19:16 ` Michal Simek
0 siblings, 1 reply; 12+ messages in thread
From: Rob Herring @ 2018-03-02 18:50 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Steffen Trumtrar, linux-kernel,
Peter Crosthwaite, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
On Fri, Feb 23, 2018 at 04:00:20PM +0100, Michal Simek wrote:
> zc770 is based board which is extended by FMC/DC cards for SoC
> validation. FMCs/DCs are supposed to cover all SoC configurations.
> FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v2:
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/zynq-zc770-xm010.dts | 92 ++++++++++++++++++++++++
> 3 files changed, 96 insertions(+)
> create mode 100644 arch/arm/boot/dts/zynq-zc770-xm010.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
> index 425c74fcc560..019e69037d42 100644
> --- a/Documentation/devicetree/bindings/arm/xilinx.txt
> +++ b/Documentation/devicetree/bindings/arm/xilinx.txt
> @@ -11,6 +11,9 @@ Additional compatible strings:
> - Xilinx internal board cc108
> "xlnx,zynq-cc108"
>
> +- Xilinx internal board zc770 with different FMC cards
> + "xlnx,zynq-zc770-xm010"
> +
> ---------------------------------------------------------------
>
> Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c6810e84d4d7..be9ffae2a1ec 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1067,6 +1067,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
> zynq-parallella.dtb \
> zynq-zc702.dtb \
> zynq-zc706.dtb \
> + zynq-zc770-xm010.dtb \
> zynq-zed.dtb \
> zynq-zybo.dtb
> dtb-$(CONFIG_MACH_ARMADA_370) += \
> diff --git a/arch/arm/boot/dts/zynq-zc770-xm010.dts b/arch/arm/boot/dts/zynq-zc770-xm010.dts
> new file mode 100644
> index 000000000000..b1cfb4ede434
> --- /dev/null
> +++ b/arch/arm/boot/dts/zynq-zc770-xm010.dts
> @@ -0,0 +1,92 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Xilinx ZC770 XM010 board DTS
> + *
> + * Copyright (C) 2013-2018 Xilinx, Inc.
> + */
> +/dts-v1/;
> +#include "zynq-7000.dtsi"
> +
> +/ {
> + compatible = "xlnx,zynq-zc770-xm010", "xlnx,zynq-7000";
> + model = "Xilinx Zynq";
> +
> + aliases {
> + ethernet0 = &gem0;
> + i2c0 = &i2c0;
> + serial0 = &uart1;
> + spi1 = &spi1;
> + };
> +
> + chosen {
> + bootargs = "";
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x40000000>;
> + };
> +
> + usb_phy0: phy0 {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +};
> +
> +&can0 {
> + status = "okay";
> +};
> +
> +&gem0 {
> + status = "okay";
> + phy-mode = "rgmii-id";
> + phy-handle = <ðernet_phy>;
> +
> + ethernet_phy: ethernet-phy@7 {
> + reg = <7>;
> + device_type = "ethernet-phy";
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + eeprom: eeprom@52 {
> + compatible = "atmel,24c02";
> + reg = <0x52>;
> + };
> +
> +};
> +
> +&sdhci0 {
> + status = "okay";
> +};
> +
> +&spi1 {
> + status = "okay";
> + num-cs = <4>;
> + is-decoded-cs = <0>;
> + flash@0 {
> + compatible = "sst25wf080", "jedec,spi-nor";
> + reg = <1>;
> + spi-max-frequency = <1000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@test {
@test?
Use a partitions node too.
> + label = "spi-flash";
Should be what the partition contains.
> + reg = <0x0 0x100000>;
> + };
> + };
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> + dr_mode = "host";
> + usb-phy = <&usb_phy0>;
> +};
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v2 2/5] arm: zynq: Add support for Xilinx zc770 xm010 dc1 board
2018-03-02 18:50 ` Rob Herring
@ 2018-03-02 19:16 ` Michal Simek
0 siblings, 0 replies; 12+ messages in thread
From: Michal Simek @ 2018-03-02 19:16 UTC (permalink / raw)
To: Rob Herring, Michal Simek
Cc: devicetree, Steffen Trumtrar, linux-kernel, Peter Crosthwaite,
Rob Herring, Mark Rutland, Josh Cartwright, Russell King,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 4067 bytes --]
On 2.3.2018 19:50, Rob Herring wrote:
> On Fri, Feb 23, 2018 at 04:00:20PM +0100, Michal Simek wrote:
>> zc770 is based board which is extended by FMC/DC cards for SoC
>> validation. FMCs/DCs are supposed to cover all SoC configurations.
>> FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
>>
>> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>> ---
>>
>> Changes in v2:
>> - Record compatible string to xilinx.txt
>>
>> Documentation/devicetree/bindings/arm/xilinx.txt | 3 +
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/zynq-zc770-xm010.dts | 92 ++++++++++++++++++++++++
>> 3 files changed, 96 insertions(+)
>> create mode 100644 arch/arm/boot/dts/zynq-zc770-xm010.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
>> index 425c74fcc560..019e69037d42 100644
>> --- a/Documentation/devicetree/bindings/arm/xilinx.txt
>> +++ b/Documentation/devicetree/bindings/arm/xilinx.txt
>> @@ -11,6 +11,9 @@ Additional compatible strings:
>> - Xilinx internal board cc108
>> "xlnx,zynq-cc108"
>>
>> +- Xilinx internal board zc770 with different FMC cards
>> + "xlnx,zynq-zc770-xm010"
>> +
>> ---------------------------------------------------------------
>>
>> Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index c6810e84d4d7..be9ffae2a1ec 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -1067,6 +1067,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
>> zynq-parallella.dtb \
>> zynq-zc702.dtb \
>> zynq-zc706.dtb \
>> + zynq-zc770-xm010.dtb \
>> zynq-zed.dtb \
>> zynq-zybo.dtb
>> dtb-$(CONFIG_MACH_ARMADA_370) += \
>> diff --git a/arch/arm/boot/dts/zynq-zc770-xm010.dts b/arch/arm/boot/dts/zynq-zc770-xm010.dts
>> new file mode 100644
>> index 000000000000..b1cfb4ede434
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/zynq-zc770-xm010.dts
>> @@ -0,0 +1,92 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Xilinx ZC770 XM010 board DTS
>> + *
>> + * Copyright (C) 2013-2018 Xilinx, Inc.
>> + */
>> +/dts-v1/;
>> +#include "zynq-7000.dtsi"
>> +
>> +/ {
>> + compatible = "xlnx,zynq-zc770-xm010", "xlnx,zynq-7000";
>> + model = "Xilinx Zynq";
>> +
>> + aliases {
>> + ethernet0 = &gem0;
>> + i2c0 = &i2c0;
>> + serial0 = &uart1;
>> + spi1 = &spi1;
>> + };
>> +
>> + chosen {
>> + bootargs = "";
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + memory@0 {
>> + device_type = "memory";
>> + reg = <0x0 0x40000000>;
>> + };
>> +
>> + usb_phy0: phy0 {
>> + compatible = "usb-nop-xceiv";
>> + #phy-cells = <0>;
>> + };
>> +};
>> +
>> +&can0 {
>> + status = "okay";
>> +};
>> +
>> +&gem0 {
>> + status = "okay";
>> + phy-mode = "rgmii-id";
>> + phy-handle = <ðernet_phy>;
>> +
>> + ethernet_phy: ethernet-phy@7 {
>> + reg = <7>;
>> + device_type = "ethernet-phy";
>> + };
>> +};
>> +
>> +&i2c0 {
>> + status = "okay";
>> + clock-frequency = <400000>;
>> +
>> + eeprom: eeprom@52 {
>> + compatible = "atmel,24c02";
>> + reg = <0x52>;
>> + };
>> +
>> +};
>> +
>> +&sdhci0 {
>> + status = "okay";
>> +};
>> +
>> +&spi1 {
>> + status = "okay";
>> + num-cs = <4>;
>> + is-decoded-cs = <0>;
>> + flash@0 {
>> + compatible = "sst25wf080", "jedec,spi-nor";
>> + reg = <1>;
>> + spi-max-frequency = <1000000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + partition@test {
>
> @test?
>
> Use a partitions node too.
ok done.
>
>> + label = "spi-flash";
>
> Should be what the partition contains.
I have fixed this to data.
Thanks,
M
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP SoCs
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 198 bytes --]
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 3/5] arm: zynq: Add support for Xilinx zc770 xm011 dc2 board
2018-02-23 15:00 [PATCH v2 0/5] arm: zynq: Adding new Xilinx boards Michal Simek
2018-02-23 15:00 ` [PATCH v2 1/5] arm: zynq: Add Xilinx cc108 board Michal Simek
2018-02-23 15:00 ` [PATCH v2 2/5] arm: zynq: Add support for Xilinx zc770 xm010 dc1 board Michal Simek
@ 2018-02-23 15:00 ` Michal Simek
2018-03-02 18:50 ` Rob Herring
2018-02-23 15:00 ` [PATCH v2 4/5] arm: zynq: Add support for Xilinx zc770 xm012 dc3 board Michal Simek
2018-02-23 15:00 ` [PATCH v2 5/5] arm: zynq: Add support for Xilinx zc770 xm013 dc4 board Michal Simek
4 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-02-23 15:00 UTC (permalink / raw)
To: devicetree
Cc: monstr, Steffen Trumtrar, linux-kernel, Peter Crosthwaite,
Rob Herring, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, i2c, nand uart, spi and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-zc770-xm011.dts | 64 ++++++++++++++++++++++++
3 files changed, 66 insertions(+)
create mode 100644 arch/arm/boot/dts/zynq-zc770-xm011.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 019e69037d42..80139a7cfcdc 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -13,6 +13,7 @@ Additional compatible strings:
- Xilinx internal board zc770 with different FMC cards
"xlnx,zynq-zc770-xm010"
+ "xlnx,zynq-zc770-xm011"
---------------------------------------------------------------
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index be9ffae2a1ec..801a46a88e93 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1068,6 +1068,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-zc702.dtb \
zynq-zc706.dtb \
zynq-zc770-xm010.dtb \
+ zynq-zc770-xm011.dtb \
zynq-zed.dtb \
zynq-zybo.dtb
dtb-$(CONFIG_MACH_ARMADA_370) += \
diff --git a/arch/arm/boot/dts/zynq-zc770-xm011.dts b/arch/arm/boot/dts/zynq-zc770-xm011.dts
new file mode 100644
index 000000000000..b78883cee96a
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-zc770-xm011.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ZC770 XM013 board DTS
+ *
+ * Copyright (C) 2013-2018 Xilinx, Inc.
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ compatible = "xlnx,zynq-zc770-xm011", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
+
+ aliases {
+ i2c0 = &i2c1;
+ serial0 = &uart1;
+ spi0 = &spi0;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x40000000>;
+ };
+
+ usb_phy1: phy1 {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+};
+
+&can0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+ usb-phy = <&usb_phy1>;
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v2 3/5] arm: zynq: Add support for Xilinx zc770 xm011 dc2 board
2018-02-23 15:00 ` [PATCH v2 3/5] arm: zynq: Add support for Xilinx zc770 xm011 dc2 board Michal Simek
@ 2018-03-02 18:50 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-02 18:50 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Steffen Trumtrar, linux-kernel,
Peter Crosthwaite, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
On Fri, Feb 23, 2018 at 04:00:21PM +0100, Michal Simek wrote:
> zc770 is based board which is extended by FMC/DC cards for SoC
> validation. FMCs/DCs are supposed to cover all SoC configurations.
> FMC/DC contains can, i2c, nand uart, spi and usb.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v2:
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/zynq-zc770-xm011.dts | 64 ++++++++++++++++++++++++
> 3 files changed, 66 insertions(+)
> create mode 100644 arch/arm/boot/dts/zynq-zc770-xm011.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 4/5] arm: zynq: Add support for Xilinx zc770 xm012 dc3 board
2018-02-23 15:00 [PATCH v2 0/5] arm: zynq: Adding new Xilinx boards Michal Simek
` (2 preceding siblings ...)
2018-02-23 15:00 ` [PATCH v2 3/5] arm: zynq: Add support for Xilinx zc770 xm011 dc2 board Michal Simek
@ 2018-02-23 15:00 ` Michal Simek
2018-03-02 18:51 ` Rob Herring
2018-02-23 15:00 ` [PATCH v2 5/5] arm: zynq: Add support for Xilinx zc770 xm013 dc4 board Michal Simek
4 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-02-23 15:00 UTC (permalink / raw)
To: devicetree
Cc: monstr, Steffen Trumtrar, linux-kernel, Peter Crosthwaite,
Rob Herring, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, 2x i2c, nor flash, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-zc770-xm012.dts | 64 ++++++++++++++++++++++++
3 files changed, 66 insertions(+)
create mode 100644 arch/arm/boot/dts/zynq-zc770-xm012.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 80139a7cfcdc..745c898f2f7f 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -14,6 +14,7 @@ Additional compatible strings:
- Xilinx internal board zc770 with different FMC cards
"xlnx,zynq-zc770-xm010"
"xlnx,zynq-zc770-xm011"
+ "xlnx,zynq-zc770-xm012"
---------------------------------------------------------------
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 801a46a88e93..2c74b935ad1c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1069,6 +1069,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-zc706.dtb \
zynq-zc770-xm010.dtb \
zynq-zc770-xm011.dtb \
+ zynq-zc770-xm012.dtb \
zynq-zed.dtb \
zynq-zybo.dtb
dtb-$(CONFIG_MACH_ARMADA_370) += \
diff --git a/arch/arm/boot/dts/zynq-zc770-xm012.dts b/arch/arm/boot/dts/zynq-zc770-xm012.dts
new file mode 100644
index 000000000000..c3169d63600d
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-zc770-xm012.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ZC770 XM012 board DTS
+ *
+ * Copyright (C) 2013-2018 Xilinx, Inc.
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ compatible = "xlnx,zynq-zc770-xm012", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ serial0 = &uart1;
+ spi0 = &spi1;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x40000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom0: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ eeprom1: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ };
+};
+
+&spi1 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+};
+
+&uart1 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v2 4/5] arm: zynq: Add support for Xilinx zc770 xm012 dc3 board
2018-02-23 15:00 ` [PATCH v2 4/5] arm: zynq: Add support for Xilinx zc770 xm012 dc3 board Michal Simek
@ 2018-03-02 18:51 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-02 18:51 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, monstr, Steffen Trumtrar, linux-kernel,
Peter Crosthwaite, Rob Herring, Mark Rutland, Josh Cartwright,
Russell King, linux-arm-kernel
On Fri, Feb 23, 2018 at 04:00:22PM +0100, Michal Simek wrote:
> zc770 is based board which is extended by FMC/DC cards for SoC
> validation. FMCs/DCs are supposed to cover all SoC configurations.
> FMC/DC contains can, 2x i2c, nor flash, spi and uart.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v2:
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/zynq-zc770-xm012.dts | 64 ++++++++++++++++++++++++
> 3 files changed, 66 insertions(+)
> create mode 100644 arch/arm/boot/dts/zynq-zc770-xm012.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 5/5] arm: zynq: Add support for Xilinx zc770 xm013 dc4 board
2018-02-23 15:00 [PATCH v2 0/5] arm: zynq: Adding new Xilinx boards Michal Simek
` (3 preceding siblings ...)
2018-02-23 15:00 ` [PATCH v2 4/5] arm: zynq: Add support for Xilinx zc770 xm012 dc3 board Michal Simek
@ 2018-02-23 15:00 ` Michal Simek
2018-03-02 18:53 ` Rob Herring
4 siblings, 1 reply; 12+ messages in thread
From: Michal Simek @ 2018-02-23 15:00 UTC (permalink / raw)
To: devicetree
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King, linux-arm-kernel
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, ethernet, i2c, qspi, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- use eeprom as node name instead of at25
- Record compatible string to xilinx.txt
Documentation/devicetree/bindings/arm/xilinx.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-zc770-xm013.dts | 78 ++++++++++++++++++++++++
3 files changed, 80 insertions(+)
create mode 100644 arch/arm/boot/dts/zynq-zc770-xm013.dts
diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt
index 745c898f2f7f..63705a451251 100644
--- a/Documentation/devicetree/bindings/arm/xilinx.txt
+++ b/Documentation/devicetree/bindings/arm/xilinx.txt
@@ -15,6 +15,7 @@ Additional compatible strings:
"xlnx,zynq-zc770-xm010"
"xlnx,zynq-zc770-xm011"
"xlnx,zynq-zc770-xm012"
+ "xlnx,zynq-zc770-xm013"
---------------------------------------------------------------
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 2c74b935ad1c..d5de3748a80a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1070,6 +1070,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
zynq-zc770-xm010.dtb \
zynq-zc770-xm011.dtb \
zynq-zc770-xm012.dtb \
+ zynq-zc770-xm013.dtb \
zynq-zed.dtb \
zynq-zybo.dtb
dtb-$(CONFIG_MACH_ARMADA_370) += \
diff --git a/arch/arm/boot/dts/zynq-zc770-xm013.dts b/arch/arm/boot/dts/zynq-zc770-xm013.dts
new file mode 100644
index 000000000000..8bb66859d774
--- /dev/null
+++ b/arch/arm/boot/dts/zynq-zc770-xm013.dts
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Xilinx ZC770 XM013 board DTS
+ *
+ * Copyright (C) 2013 Xilinx, Inc.
+ */
+/dts-v1/;
+#include "zynq-7000.dtsi"
+
+/ {
+ compatible = "xlnx,zynq-zc770-xm013", "xlnx,zynq-7000";
+ model = "Xilinx Zynq";
+
+ aliases {
+ ethernet0 = &gem1;
+ i2c0 = &i2c1;
+ serial0 = &uart0;
+ spi1 = &spi0;
+ };
+
+ chosen {
+ bootargs = "";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x40000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&gem1 {
+ status = "okay";
+ phy-mode = "rgmii-id";
+ phy-handle = <ðernet_phy>;
+
+ ethernet_phy: ethernet-phy@7 {
+ reg = <7>;
+ device_type = "ethernet-phy";
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ si570: clock-generator@55 {
+ #clock-cells = <0>;
+ compatible = "silabs,si570";
+ temperature-stability = <50>;
+ reg = <0x55>;
+ factory-fout = <156250000>;
+ clock-frequency = <148500000>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+ num-cs = <4>;
+ is-decoded-cs = <0>;
+ eeprom: eeprom@0 {
+ at25,byte-len = <8192>;
+ at25,addr-mode = <2>;
+ at25,page-size = <32>;
+
+ compatible = "atmel,at25";
+ reg = <2>;
+ spi-max-frequency = <1000000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v2 5/5] arm: zynq: Add support for Xilinx zc770 xm013 dc4 board
2018-02-23 15:00 ` [PATCH v2 5/5] arm: zynq: Add support for Xilinx zc770 xm013 dc4 board Michal Simek
@ 2018-03-02 18:53 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2018-03-02 18:53 UTC (permalink / raw)
To: Michal Simek
Cc: devicetree, linux-kernel, Mark Rutland, Russell King, linux-arm-kernel
On Fri, Feb 23, 2018 at 04:00:23PM +0100, Michal Simek wrote:
> zc770 is based board which is extended by FMC/DC cards for SoC
> validation. FMCs/DCs are supposed to cover all SoC configurations.
> FMC/DC contains can, ethernet, i2c, qspi, spi and uart.
>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> Changes in v2:
> - use eeprom as node name instead of at25
> - Record compatible string to xilinx.txt
>
> Documentation/devicetree/bindings/arm/xilinx.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/zynq-zc770-xm013.dts | 78 ++++++++++++++++++++++++
> 3 files changed, 80 insertions(+)
> create mode 100644 arch/arm/boot/dts/zynq-zc770-xm013.dts
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread