linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Kishon Vijay Abraham I <kishon@ti.com>
To: Ulf Hansson <ulf.hansson@linaro.org>,
	Adrian Hunter <adrian.hunter@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>, <linux-mmc@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-omap@vger.kernel.org>, <kishon@ti.com>
Subject: [PATCH v5 09/14] mmc: sdhci-omap: Workaround for Errata i834
Date: Fri, 27 Apr 2018 17:17:18 +0530	[thread overview]
Message-ID: <20180427114723.2687-10-kishon@ti.com> (raw)
In-Reply-To: <20180427114723.2687-1-kishon@ti.com>

Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.

The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
 drivers/mmc/host/sdhci-omap.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index d5c1a9c71f95..2232a9974b21 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -715,7 +715,8 @@ static const struct sdhci_pltfm_data sdhci_omap_pdata = {
 		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC,
 	.quirks2 = SDHCI_QUIRK2_ACMD23_BROKEN |
 		   SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
-		   SDHCI_QUIRK2_RSP_136_HAS_CRC,
+		   SDHCI_QUIRK2_RSP_136_HAS_CRC |
+		   SDHCI_QUIRK2_DISABLE_HW_TIMEOUT,
 	.ops = &sdhci_omap_ops,
 };
 
-- 
2.17.0

  parent reply	other threads:[~2018-04-27 11:48 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-04-27 11:47 [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 01/14] mmc: sdhci-omap: Fix when capabilities are obtained from SDHCI_CAPABILITIES reg Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 02/14] mmc: sdhci-omap: Remove setting ADMA capability in driver Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 03/14] mmc: sdhci-omap: Workaround for Errata i843 Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 04/14] mmc: sdhci-omap: Invoke sdhci_get_of_property to read sdhci dt properties Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 05/14] mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't support 1.8v Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 06/14] mmc: sdhci: Add quirk to disable HW timeout Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 07/14] mmc: sdhci: Factor out target_timeout calculation Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 08/14] mmc: sdhci: Program a relatively accurate SW timeout value Kishon Vijay Abraham I
2018-04-27 11:47 ` Kishon Vijay Abraham I [this message]
2018-04-27 11:47 ` [PATCH v5 10/14] dt-bindings: sdhci-omap: Add K2G specific binding Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 11/14] mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 12/14] mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 13/14] dt-bindings: sdhci-omap: Add pinctrl bindings Kishon Vijay Abraham I
2018-04-27 14:26   ` Rob Herring
2018-04-27 11:47 ` [PATCH v5 14/14] mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode Kishon Vijay Abraham I
2018-05-02 13:15 ` [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support Ulf Hansson
2018-05-02 14:55   ` Tony Lindgren
2018-05-03  8:51     ` Ulf Hansson
2018-05-03 14:12       ` Tony Lindgren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180427114723.2687-10-kishon@ti.com \
    --to=kishon@ti.com \
    --cc=adrian.hunter@intel.com \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).