From: Kishon Vijay Abraham I <kishon@ti.com>
To: Ulf Hansson <ulf.hansson@linaro.org>,
Adrian Hunter <adrian.hunter@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>, <linux-mmc@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-omap@vger.kernel.org>, <kishon@ti.com>
Subject: [PATCH v5 14/14] mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode
Date: Fri, 27 Apr 2018 17:17:23 +0530 [thread overview]
Message-ID: <20180427114723.2687-15-kishon@ti.com> (raw)
In-Reply-To: <20180427114723.2687-1-kishon@ti.com>
commit 8d20b2eae6c47b095523 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/mmc/host/sdhci-omap.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
index bd5e03d177e0..f3a7c8ece4be 100644
--- a/drivers/mmc/host/sdhci-omap.c
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -842,8 +842,15 @@ static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_1_8v", caps,
MMC_CAP_1_8V_DDR);
- if (!IS_ERR(state))
+ if (!IS_ERR(state)) {
pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+ } else {
+ state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_3_3v",
+ caps,
+ MMC_CAP_3_3V_DDR);
+ if (!IS_ERR(state))
+ pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+ }
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs", caps,
MMC_CAP_SD_HIGHSPEED);
--
2.17.0
next prev parent reply other threads:[~2018-04-27 11:48 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-04-27 11:47 [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 01/14] mmc: sdhci-omap: Fix when capabilities are obtained from SDHCI_CAPABILITIES reg Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 02/14] mmc: sdhci-omap: Remove setting ADMA capability in driver Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 03/14] mmc: sdhci-omap: Workaround for Errata i843 Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 04/14] mmc: sdhci-omap: Invoke sdhci_get_of_property to read sdhci dt properties Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 05/14] mmc: sdhci: Disable 1.8v modes (HS200/HS400/UHS) if controller can't support 1.8v Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 06/14] mmc: sdhci: Add quirk to disable HW timeout Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 07/14] mmc: sdhci: Factor out target_timeout calculation Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 08/14] mmc: sdhci: Program a relatively accurate SW timeout value Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 09/14] mmc: sdhci-omap: Workaround for Errata i834 Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 10/14] dt-bindings: sdhci-omap: Add K2G specific binding Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 11/14] mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 12/14] mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq Kishon Vijay Abraham I
2018-04-27 11:47 ` [PATCH v5 13/14] dt-bindings: sdhci-omap: Add pinctrl bindings Kishon Vijay Abraham I
2018-04-27 14:26 ` Rob Herring
2018-04-27 11:47 ` Kishon Vijay Abraham I [this message]
2018-05-02 13:15 ` [PATCH v5 00/14] mmc: sdhci-omap: Add UHS/HS200 mode support Ulf Hansson
2018-05-02 14:55 ` Tony Lindgren
2018-05-03 8:51 ` Ulf Hansson
2018-05-03 14:12 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180427114723.2687-15-kishon@ti.com \
--to=kishon@ti.com \
--cc=adrian.hunter@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).