From: Icenowy Zheng <icenowy@aosc.io>
To: Rob Herring <robh+dt@kernel.org>,
Maxime Ripard <maxime.ripard@bootlin.com>,
Chen-Yu Tsai <wens@csie.org>,
Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com,
Icenowy Zheng <icenowy@aosc.io>
Subject: [PATCH v2 3/9] arm64: allwinner: dts: h6: add USB2-related device nodes
Date: Fri, 6 Jul 2018 23:37:59 +0800 [thread overview]
Message-ID: <20180706153805.25842-4-icenowy@aosc.io> (raw)
In-Reply-To: <20180706153805.25842-1-icenowy@aosc.io>
Allwinner H6 has two USB2 ports, one OTG and one host-only.
Add device tree nodes related to them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 90 ++++++++++++++++++++
1 file changed, 90 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index c72da8cd9ef5..62fc0f5e10ba 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -174,6 +174,96 @@
status = "disabled";
};
+ usb2otg: usb@5100000 {
+ compatible = "allwinner,sun8i-a33-musb";
+ reg = <0x05100000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usb2phy 0>;
+ phy-names = "usb";
+ extcon = <&usb2phy 0>;
+ status = "disabled";
+ };
+
+ usb2phy: phy@5100400 {
+ compatible = "allwinner,sun50i-h6-usb-phy";
+ reg = <0x05100400 0x14>,
+ <0x05101800 0x4>,
+ <0x05311800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@5101000 {
+ compatible = "allwinner,sun50i-h6-ehci", "generic-ehci";
+ reg = <0x05101000 0x100>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_BUS_EHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>,
+ <&ccu RST_BUS_EHCI0>;
+ status = "disabled";
+ };
+
+ ohci0: usb@5101400 {
+ compatible = "allwinner,sun50i-h6-ohci", "generic-ohci";
+ reg = <0x05101400 0x100>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ status = "disabled";
+ };
+
+ usb3phy: phy@5210000 {
+ compatible = "allwinner,sun50i-h6-usb3-phy";
+ reg = <0x5210000 0x10000>;
+ clocks = <&ccu CLK_USB_PHY1>;
+ resets = <&ccu RST_USB_PHY1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ ehci3: usb@5311000 {
+ compatible = "allwinner,sun50i-h6-ehci", "generic-ehci";
+ reg = <0x05311000 0x100>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_BUS_EHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_OHCI3>,
+ <&ccu RST_BUS_EHCI3>;
+ phys = <&usb2phy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb@5311400 {
+ compatible = "allwinner,sun50i-h6-ohci", "generic-ohci";
+ reg = <0x05311400 0x100>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_OHCI3>;
+ phys = <&usb2phy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
r_ccu: clock@7010000 {
compatible = "allwinner,sun50i-h6-r-ccu";
reg = <0x07010000 0x400>;
--
2.17.1
next prev parent reply other threads:[~2018-07-06 15:44 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-06 15:37 [PATCH v2 0/9] Allwinner H6 USB support Icenowy Zheng
2018-07-06 15:37 ` [PATCH v2 1/9] phy: sun4i-usb: add support for missing USB PHY index Icenowy Zheng
2018-07-06 15:37 ` [PATCH v2 2/9] phy: sun4i-usb: add support for H6 USB2 PHY Icenowy Zheng
2018-07-06 15:37 ` Icenowy Zheng [this message]
2018-07-07 3:31 ` [linux-sunxi] [PATCH v2 3/9] arm64: allwinner: dts: h6: add USB2-related device nodes Chen-Yu Tsai
2018-07-07 3:33 ` Icenowy Zheng
2018-07-06 15:38 ` [PATCH v2 4/9] arm64: allwinner: dts: h6: add USB Vbus regulator Icenowy Zheng
2018-07-06 15:38 ` [PATCH v2 5/9] arm64: allwinner: dts: h6: enable USB2 on Pine H64 Icenowy Zheng
2018-07-07 3:38 ` [linux-sunxi] " Chen-Yu Tsai
2018-07-06 15:38 ` [PATCH v2 6/9] dt-bindings: phy: add binding for Allwinner USB3 PHY Icenowy Zheng
2018-07-11 16:13 ` Rob Herring
2018-07-11 16:19 ` Icenowy Zheng
2018-07-11 17:39 ` Rob Herring
2018-07-06 15:38 ` [PATCH v2 7/9] phy: allwinner: add phy driver for USB3 PHY on Allwinner H6 SoC Icenowy Zheng
2018-07-09 4:31 ` Kishon Vijay Abraham I
2018-07-09 4:36 ` Chen-Yu Tsai
2018-07-09 4:40 ` [linux-sunxi] " Icenowy Zheng
2018-07-06 15:38 ` [PATCH v2 8/9] arm64: allwinner: dts: h6: add USB3 device nodes Icenowy Zheng
2018-07-07 3:35 ` [linux-sunxi] " Chen-Yu Tsai
2018-07-07 3:37 ` Icenowy Zheng
2018-07-06 15:38 ` [PATCH v2 9/9] arm64: allwinner: dts: h6: enable USB3 port on Pine H64 Icenowy Zheng
2018-07-09 2:52 ` [linux-sunxi] [PATCH v2 0/9] Allwinner H6 USB support Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180706153805.25842-4-icenowy@aosc.io \
--to=icenowy@aosc.io \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=maxime.ripard@bootlin.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).