[PATCH 0/5] midas: fix IRQ pin configuration

[PATCH 0/5] midas: fix IRQ pin configuration

[Simon Shields]

This patch series disables the internal pull-up/down resistors
for IRQ lines which are pulled up externally. Without these patches the
associated IRQs never fire if the bootloader hasn't configured the pins
correctly.

Simon Shields (5):
  ARM: dts: exynos: add max77693 pinctrl config for midas
  ARM: dts: exynos: add pinctrl config for midas keys
  ARM: dts: exynos: add pinctrl for midas fuelgauge irq pin
  ARM: dts: exynos: configure max77686 IRQ pin on midas
  ARM: dts: exynos: configure midas SD card CD pin

 arch/arm/boot/dts/exynos4412-midas.dtsi | 35 ++++++++++++++++++++++++-
 1 file changed, 34 insertions(+), 1 deletion(-)

-- 
2.18.0

[PATCH 1/5] ARM: dts: exynos: add max77693 pinctrl config for midas

[Simon Shields]

Currently, we assume that the bootloader has correctly configured
the interrupt pin for max77693. This might not actually be the case -
so it's better to configure it explicitly.

Signed-off-by: Simon Shields <simon@lineageos.org>
---
 arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi
index f12372509061..ee7cda1432f7 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -156,6 +156,8 @@
 			compatible = "maxim,max77693";
 			interrupt-parent = <&gpx1>;
 			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77693_irq>;
 			reg = <0x66>;
 
 			regulators {
@@ -1124,6 +1126,11 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep1>;
 
+	max77693_irq: max77693-irq {
+		samsung,pins = "gpx1-5";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	hdmi_hpd: hdmi-hpd {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
-- 
2.18.0

Re: [PATCH 1/5] ARM: dts: exynos: add max77693 pinctrl config for midas

[Krzysztof Kozlowski]

On Sat, Jul 21, 2018 at 10:50:49PM +1000, Simon Shields wrote:
> Currently, we assume that the bootloader has correctly configured
> the interrupt pin for max77693. This might not actually be the case -
> so it's better to configure it explicitly.
> 
> Signed-off-by: Simon Shields <simon@lineageos.org>
> ---
>  arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
>  1 file changed, 7 insertions(+)

Thanks, applied.

Best regards,
Krzysztof

[PATCH 2/5] ARM: dts: exynos: add pinctrl config for midas keys

[Simon Shields]

This pins are externally pulled up, and so we should explicitly
configure them to disable the SoC-internal pull-downs. Previously
we relied on the bootloader doing this in order to allow the buttons
to function properly.

Signed-off-by: Simon Shields <simon@lineageos.org>
---
 arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi
index ee7cda1432f7..6f7b564905ab 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -112,6 +112,8 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
 
 		key-down {
 			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
@@ -1126,6 +1128,11 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep1>;
 
+	gpio_keys: gpio-keys {
+		samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	max77693_irq: max77693-irq {
 		samsung,pins = "gpx1-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-- 
2.18.0

Re: [PATCH 2/5] ARM: dts: exynos: add pinctrl config for midas keys

[Krzysztof Kozlowski]

On Sat, Jul 21, 2018 at 10:50:50PM +1000, Simon Shields wrote:
> This pins are externally pulled up, and so we should explicitly
> configure them to disable the SoC-internal pull-downs. Previously
> we relied on the bootloader doing this in order to allow the buttons
> to function properly.
> 
> Signed-off-by: Simon Shields <simon@lineageos.org>
> ---
>  arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
>  1 file changed, 7 insertions(+)

Thanks, applied.

Best regards,
Krzysztof

[PATCH 3/5] ARM: dts: exynos: add pinctrl for midas fuelgauge irq pin

[Simon Shields]

This pin is externally pulled up, so we should disable the SoC's
pull down resistor in order for the interrupt to function properly.

Signed-off-by: Simon Shields <simon@lineageos.org>
---
 arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi
index 6f7b564905ab..6a6364a9debd 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -206,6 +206,8 @@
 			compatible = "maxim,max17047";
 			interrupt-parent = <&gpx2>;
 			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77693_fuel_irq>;
 			reg = <0x36>;
 
 			maxim,over-heat-temp = <700>;
@@ -1138,6 +1140,11 @@
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
+	max77693_fuel_irq: max77693-fuel-irq {
+		samsung,pins = "gpx2-3";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	hdmi_hpd: hdmi-hpd {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
-- 
2.18.0

Re: [PATCH 3/5] ARM: dts: exynos: add pinctrl for midas fuelgauge irq pin

[Krzysztof Kozlowski]

On Sat, Jul 21, 2018 at 10:50:51PM +1000, Simon Shields wrote:
> This pin is externally pulled up, so we should disable the SoC's
> pull down resistor in order for the interrupt to function properly.
> 
> Signed-off-by: Simon Shields <simon@lineageos.org>
> ---
>  arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
>  1 file changed, 7 insertions(+)

Thanks, applied.

Best regards,
Krzysztof

[PATCH 4/5] ARM: dts: exynos: configure max77686 IRQ pin on midas

[Simon Shields]

This pin is externally pulled up, so we need to disable the
SoC's internal pull-down.

Signed-off-by: Simon Shields <simon@lineageos.org>
---
 arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi
index 6a6364a9debd..d69bc3c2d0ff 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -685,6 +685,8 @@
 		compatible = "maxim,max77686";
 		interrupt-parent = <&gpx0>;
 		interrupts = <7 IRQ_TYPE_NONE>;
+		pinctrl-0 = <&max77686_irq>;
+		pinctrl-names = "default";
 		reg = <0x09>;
 		#clock-cells = <1>;
 
@@ -1135,6 +1137,11 @@
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
+	max77686_irq: max77686-irq {
+		samsung,pins = "gpx0-7";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	max77693_irq: max77693-irq {
 		samsung,pins = "gpx1-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-- 
2.18.0

Re: [PATCH 4/5] ARM: dts: exynos: configure max77686 IRQ pin on midas

[Krzysztof Kozlowski]

On Sat, Jul 21, 2018 at 10:50:52PM +1000, Simon Shields wrote:
> This pin is externally pulled up, so we need to disable the
> SoC's internal pull-down.
> 
> Signed-off-by: Simon Shields <simon@lineageos.org>
> ---
>  arch/arm/boot/dts/exynos4412-midas.dtsi | 7 +++++++
>  1 file changed, 7 insertions(+)

Thanks, applied.

Best regards,
Krzysztof

[PATCH 5/5] ARM: dts: exynos: configure midas SD card CD pin

[Simon Shields]

This pin is externally pulled up, so we need to disable the SoC's
internal pull down resistor to allow it to function properly.

Signed-off-by: Simon Shields <simon@lineageos.org>
---
 arch/arm/boot/dts/exynos4412-midas.dtsi | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi
index d69bc3c2d0ff..3d3e6b74c12e 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -1152,6 +1152,11 @@
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
+	sdhci2_cd: sdhci2-cd-irq {
+		samsung,pins = "gpx3-4";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
 	hdmi_hpd: hdmi-hpd {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -1383,7 +1388,7 @@
 	bus-width = <4>;
 	cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
-	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
 	pinctrl-names = "default";
 	vmmc-supply = <&ldo21_reg>;
 	status = "okay";
-- 
2.18.0

Re: [PATCH 5/5] ARM: dts: exynos: configure midas SD card CD pin

[Krzysztof Kozlowski]

On Sat, Jul 21, 2018 at 10:50:53PM +1000, Simon Shields wrote:
> This pin is externally pulled up, so we need to disable the SoC's
> internal pull down resistor to allow it to function properly.
> 
> Signed-off-by: Simon Shields <simon@lineageos.org>
> ---
>  arch/arm/boot/dts/exynos4412-midas.dtsi | 7 ++++++-
>  1 file changed, 6 insertions(+), 1 deletion(-)

Thanks, applied.

Best regards,
Krzysztof