* [PATCH v2 1/2] dt-bindings: phy: Add Qualcomm Synopsys High-Speed USB PHY binding
2018-11-12 13:00 [PATCH v2 0/2] Add Synopsys High-Speed USB PHY driver for Qualcomm SoCs Shawn Guo
@ 2018-11-12 13:00 ` Shawn Guo
2018-11-12 13:00 ` [PATCH v2 2/2] phy: qualcomm: Add Synopsys High-Speed USB PHY driver Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2018-11-12 13:00 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Rob Herring, Sriharsha Allenki, Anu Ramanathan, Bjorn Andersson,
Vinod Koul, linux-arm-msm, devicetree, linux-kernel, Shawn Guo
From: Sriharsha Allenki <sallenki@codeaurora.org>
It adds bindings for Synopsys 28nm femto phy controller that supports
LS/FS/HS usb connectivity on Qualcomm chipsets.
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
.../phy/qcom,snps-28nm-usb-hs-phy.txt | 101 ++++++++++++++++++
1 file changed, 101 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,snps-28nm-usb-hs-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom,snps-28nm-usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,snps-28nm-usb-hs-phy.txt
new file mode 100644
index 000000000000..1df0c6bf7bd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,snps-28nm-usb-hs-phy.txt
@@ -0,0 +1,101 @@
+Qualcomm Synopsys 28nm Femto phy controller
+===========================================
+
+Synopsys 28nm femto phy controller supports LS/FS/HS usb connectivity on
+Qualcomm chipsets.
+
+Required properties:
+
+- compatible:
+ Value type: <string>
+ Definition: Should contain "qcom,usb-snps-hsphy".
+
+- reg:
+ Value type: <prop-encoded-array>
+ Definition: USB PHY base address and length of the register map.
+
+- #phy-cells:
+ Value type: <u32>
+ Definition: Should be 0. See phy/phy-bindings.txt for details.
+
+- clocks:
+ Value type: <prop-encoded-array>
+ Definition: See clock-bindings.txt section "consumers". List of
+ three clock specifiers for reference, phy core and
+ sleep clocks.
+
+- clock-names:
+ Value type: <string>
+ Definition: Names of the clocks in 1-1 correspondence with the "clocks"
+ property. Must contain "ref", "phy" and "sleep".
+
+- resets:
+ Value type: <prop-encoded-array>
+ Definition: See reset.txt section "consumers". PHY reset specifiers
+ for phy core and POR resets.
+
+- reset-names:
+ Value type: <string>
+ Definition: Names of the resets in 1-1 correspondence with the "resets"
+ property. Must contain "phy" and "por".
+
+- vdd-supply:
+ Value type: <phandle>
+ Definition: phandle to the regulator VDD supply node.
+
+- vdda1p8-supply:
+ Value type: <phandle>
+ Definition: phandle to the regulator 1.8V supply node.
+
+- vdda3p3-supply:
+ Value type: <phandle>
+ Definition: phandle to the regulator 3.3V supply node.
+
+- qcom,vdd-voltage-level:
+ Value type: <prop-array>
+ Definition: This is a list of three integer values <no min max> where
+ each value corresponding to voltage corner in uV.
+
+Optional properties:
+
+- extcon:
+ Value type: <prop-encoded-array>
+ Definition: Should contain the vbus extcon.
+
+- qcom,init-seq:
+ Value type: <u32 array>
+ Definition: Should contain a sequence of <offset value delay> tuples to
+ program 'value' into phy register at 'offset' with 'delay'
+ in us afterwards.
+
+Example:
+
+ phy@7a000 {
+ compatible = "qcom,usb-snps-hsphy";
+ reg = <0x7a000 0x200>;
+ #phy-cells = <0>;
+ clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+ <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "phy", "sleep";
+ resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
+ <&gcc GCC_USB2A_PHY_BCR>;
+ reset-names = "phy", "por";
+ vdd-supply = <&vreg_l4_1p2>;
+ vdda1p8-supply = <&vreg_l5_1p8>;
+ vdda3p3-supply = <&vreg_l12_3p3>;
+ qcom,vdd-voltage-level = <0 1144000 1200000>;
+ qcom,init-seq = <0xc0 0x01 0>,
+ <0xe8 0x0d 0>,
+ <0x74 0x12 0>,
+ <0x98 0x63 0>,
+ <0x9c 0x03 0>,
+ <0xa0 0x1d 0>,
+ <0xa4 0x03 0>,
+ <0x8c 0x23 0>,
+ <0x78 0x08 0>,
+ <0x7c 0xdc 0>,
+ <0x90 0xe0 20>,
+ <0x74 0x10 0>,
+ <0x90 0x60 0>;
+ };
--
2.18.0
^ permalink raw reply related [flat|nested] 3+ messages in thread* [PATCH v2 2/2] phy: qualcomm: Add Synopsys High-Speed USB PHY driver
2018-11-12 13:00 [PATCH v2 0/2] Add Synopsys High-Speed USB PHY driver for Qualcomm SoCs Shawn Guo
2018-11-12 13:00 ` [PATCH v2 1/2] dt-bindings: phy: Add Qualcomm Synopsys High-Speed USB PHY binding Shawn Guo
@ 2018-11-12 13:00 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2018-11-12 13:00 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Rob Herring, Sriharsha Allenki, Anu Ramanathan, Bjorn Andersson,
Vinod Koul, linux-arm-msm, devicetree, linux-kernel, Shawn Guo
It adds Synopsys 28nm Femto High-Speed USB PHY driver support, which
is usually paired with Synopsys DWC3 USB controllers on Qualcomm SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
drivers/phy/qualcomm/Kconfig | 10 +
drivers/phy/qualcomm/Makefile | 1 +
.../phy/qualcomm/phy-qcom-usb-hs-snsp-28nm.c | 505 ++++++++++++++++++
3 files changed, 516 insertions(+)
create mode 100644 drivers/phy/qualcomm/phy-qcom-usb-hs-snsp-28nm.c
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
index 32f7d34eb784..c7b5ee82895d 100644
--- a/drivers/phy/qualcomm/Kconfig
+++ b/drivers/phy/qualcomm/Kconfig
@@ -82,3 +82,13 @@ config PHY_QCOM_USB_HSIC
select GENERIC_PHY
help
Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
+config PHY_QCOM_USB_HS_SNPS_28NM
+ tristate "Qualcomm Synopsys 28nm USB HS PHY driver"
+ depends on ARCH_QCOM || COMPILE_TEST
+ depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+ select GENERIC_PHY
+ help
+ Enable this to support the Synopsys 28nm Femto USB PHY on Qualcomm
+ chips. This driver supports the high-speed PHY which is usually
+ paired with either the ChipIdea or Synopsys DWC3 USB IPs on MSM SOCs.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
index c56efd3af205..dc238d95b18c 100644
--- a/drivers/phy/qualcomm/Makefile
+++ b/drivers/phy/qualcomm/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM) += phy-qcom-ufs-qmp-14nm.o
obj-$(CONFIG_PHY_QCOM_UFS_20NM) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
+obj-$(CONFIG_PHY_QCOM_USB_HS_SNPS_28NM) += phy-qcom-usb-hs-snsp-28nm.o
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hs-snsp-28nm.c b/drivers/phy/qualcomm/phy-qcom-usb-hs-snsp-28nm.c
new file mode 100644
index 000000000000..589d417dbb7b
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-usb-hs-snsp-28nm.c
@@ -0,0 +1,505 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2009-2018, Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, Linaro Limited
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/extcon.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/notifier.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+/* PHY register and bit definitions */
+#define PHY_CTRL_COMMON0 0x078
+#define SIDDQ BIT(2)
+#define PHY_IRQ_CMD 0x0d0
+#define PHY_INTR_MASK0 0x0d4
+#define PHY_INTR_CLEAR0 0x0dc
+#define DPDM_MASK 0x1e
+#define DP_1_0 BIT(4)
+#define DP_0_1 BIT(3)
+#define DM_1_0 BIT(2)
+#define DM_0_1 BIT(1)
+
+enum hsphy_voltage {
+ VOL_NONE,
+ VOL_MIN,
+ VOL_MAX,
+ VOL_NUM,
+};
+
+enum hsphy_vreg {
+ VDD,
+ VDDA_1P8,
+ VDDA_3P3,
+ VREG_NUM,
+};
+
+struct hsphy_init_seq {
+ int offset;
+ int val;
+ int delay;
+};
+
+struct hsphy_priv {
+ void __iomem *base;
+ struct clk_bulk_data *clks;
+ int num_clks;
+ struct reset_control *phy_reset;
+ struct reset_control *por_reset;
+ struct regulator_bulk_data vregs[VREG_NUM];
+ unsigned int voltages[VREG_NUM][VOL_NUM];
+ struct hsphy_init_seq *init_seq;
+ bool cable_connected;
+ struct extcon_dev *vbus_edev;
+ struct notifier_block vbus_notify;
+ enum phy_mode mode;
+};
+
+static int qcom_snps_hsphy_config_regulators(struct hsphy_priv *priv, int high)
+{
+ int old_uV[VREG_NUM];
+ int min, ret, i;
+
+ min = high ? 1 : 0; /* low or none? */
+
+ for (i = 0; i < VREG_NUM; i++) {
+ old_uV[i] = regulator_get_voltage(priv->vregs[i].consumer);
+ ret = regulator_set_voltage(priv->vregs[i].consumer,
+ priv->voltages[i][min],
+ priv->voltages[i][VOL_MAX]);
+ if (ret)
+ goto roll_back;
+ }
+
+ return 0;
+
+roll_back:
+ for (; i >= 0; i--)
+ regulator_set_voltage(priv->vregs[i].consumer,
+ old_uV[i], old_uV[i]);
+ return ret;
+}
+
+static int qcom_snps_hsphy_enable_regulators(struct hsphy_priv *priv)
+{
+ int ret;
+
+ ret = qcom_snps_hsphy_config_regulators(priv, 1);
+ if (ret)
+ return ret;
+
+ ret = regulator_set_load(priv->vregs[VDDA_1P8].consumer, 19000);
+ if (ret < 0)
+ goto unconfig_regulators;
+
+ ret = regulator_set_load(priv->vregs[VDDA_3P3].consumer, 16000);
+ if (ret < 0)
+ goto unset_1p8_load;
+
+ ret = regulator_bulk_enable(VREG_NUM, priv->vregs);
+ if (ret)
+ goto unset_3p3_load;
+
+ return 0;
+
+unset_3p3_load:
+ regulator_set_load(priv->vregs[VDDA_3P3].consumer, 0);
+unset_1p8_load:
+ regulator_set_load(priv->vregs[VDDA_1P8].consumer, 0);
+unconfig_regulators:
+ qcom_snps_hsphy_config_regulators(priv, 0);
+ return ret;
+}
+
+static void qcom_snps_hsphy_disable_regulators(struct hsphy_priv *priv)
+{
+ regulator_bulk_disable(VREG_NUM, priv->vregs);
+ regulator_set_load(priv->vregs[VDDA_1P8].consumer, 0);
+ regulator_set_load(priv->vregs[VDDA_3P3].consumer, 0);
+ qcom_snps_hsphy_config_regulators(priv, 0);
+}
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+ priv->mode = mode;
+
+ return 0;
+}
+
+static void qcom_snps_hsphy_enable_hv_interrupts(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ /* Clear any existing interrupts before enabling the interrupts */
+ val = readb(priv->base + PHY_INTR_CLEAR0);
+ val |= DPDM_MASK;
+ writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+ writeb(0x0, priv->base + PHY_IRQ_CMD);
+ usleep_range(200, 220);
+ writeb(0x1, priv->base + PHY_IRQ_CMD);
+
+ /* Make sure the interrupts are cleared */
+ usleep_range(200, 220);
+
+ val = readb(priv->base + PHY_INTR_MASK0);
+ switch (priv->mode) {
+ case PHY_MODE_USB_HOST_HS:
+ case PHY_MODE_USB_HOST_FS:
+ case PHY_MODE_USB_DEVICE_HS:
+ case PHY_MODE_USB_DEVICE_FS:
+ val |= DP_1_0 | DM_0_1;
+ break;
+ case PHY_MODE_USB_HOST_LS:
+ case PHY_MODE_USB_DEVICE_LS:
+ val |= DP_0_1 | DM_1_0;
+ break;
+ default:
+ /* No device connected */
+ val |= DP_0_1 | DM_0_1;
+ break;
+ }
+ writeb(val, priv->base + PHY_INTR_MASK0);
+}
+
+static void qcom_snps_hsphy_disable_hv_interrupts(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ val = readb(priv->base + PHY_INTR_MASK0);
+ val &= ~DPDM_MASK;
+ writeb(val, priv->base + PHY_INTR_MASK0);
+
+ /* Clear any pending interrupts */
+ val = readb(priv->base + PHY_INTR_CLEAR0);
+ val |= DPDM_MASK;
+ writeb(val, priv->base + PHY_INTR_CLEAR0);
+
+ writeb(0x0, priv->base + PHY_IRQ_CMD);
+ usleep_range(200, 220);
+
+ writeb(0x1, priv->base + PHY_IRQ_CMD);
+ usleep_range(200, 220);
+}
+
+static void qcom_snps_hsphy_enter_retention(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ val = readb(priv->base + PHY_CTRL_COMMON0);
+ val |= SIDDQ;
+ writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static void qcom_snps_hsphy_exit_retention(struct hsphy_priv *priv)
+{
+ u32 val;
+
+ val = readb(priv->base + PHY_CTRL_COMMON0);
+ val &= ~SIDDQ;
+ writeb(val, priv->base + PHY_CTRL_COMMON0);
+}
+
+static int qcom_snps_hsphy_vbus_notifier(struct notifier_block *nb,
+ unsigned long event, void *ptr)
+{
+ struct hsphy_priv *priv = container_of(nb, struct hsphy_priv,
+ vbus_notify);
+ priv->cable_connected = !!event;
+ return 0;
+}
+
+static int qcom_snps_hsphy_power_on(struct phy *phy)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+ int ret;
+
+ if (priv->cable_connected) {
+ ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+ if (ret)
+ return ret;
+ qcom_snps_hsphy_disable_hv_interrupts(priv);
+ } else {
+ ret = qcom_snps_hsphy_enable_regulators(priv);
+ if (ret)
+ return ret;
+ ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+ if (ret)
+ return ret;
+ qcom_snps_hsphy_exit_retention(priv);
+ }
+
+ return 0;
+}
+
+static int qcom_snps_hsphy_power_off(struct phy *phy)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+
+ if (priv->cable_connected) {
+ qcom_snps_hsphy_enable_hv_interrupts(priv);
+ clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+ } else {
+ qcom_snps_hsphy_enter_retention(priv);
+ clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+ qcom_snps_hsphy_disable_regulators(priv);
+ }
+
+ return 0;
+}
+
+static int qcom_snps_hsphy_reset(struct hsphy_priv *priv)
+{
+ int ret;
+
+ ret = reset_control_assert(priv->phy_reset);
+ if (ret)
+ return ret;
+
+ usleep_range(10, 15);
+
+ ret = reset_control_deassert(priv->phy_reset);
+ if (ret)
+ return ret;
+
+ usleep_range(80, 100);
+
+ return 0;
+}
+
+static void qcom_snps_hsphy_init_sequence(struct hsphy_priv *priv)
+{
+ struct hsphy_init_seq *seq;
+
+ for (seq = priv->init_seq; seq->offset != -1; seq++) {
+ writeb(seq->val, priv->base + seq->offset);
+ if (seq->delay)
+ usleep_range(seq->delay, seq->delay + 10);
+ }
+
+ /* Ensure that the above parameter overrides is successful. */
+ mb();
+}
+
+static int qcom_snps_hsphy_por_reset(struct hsphy_priv *priv)
+{
+ int ret;
+
+ ret = reset_control_assert(priv->por_reset);
+ if (ret)
+ return ret;
+
+ /*
+ * The Femto PHY is POR reset in the following scenarios.
+ *
+ * 1. After overriding the parameter registers.
+ * 2. Low power mode exit from PHY retention.
+ *
+ * Ensure that SIDDQ is cleared before bringing the PHY
+ * out of reset.
+ */
+ qcom_snps_hsphy_exit_retention(priv);
+
+ /*
+ * As per databook, 10 usec delay is required between
+ * PHY POR assert and de-assert.
+ */
+ usleep_range(10, 20);
+ ret = reset_control_deassert(priv->por_reset);
+ if (ret)
+ return ret;
+
+ /*
+ * As per databook, it takes 75 usec for PHY to stabilize
+ * after the reset.
+ */
+ usleep_range(80, 100);
+
+ /* Ensure that RESET operation is completed. */
+ mb();
+
+ return 0;
+}
+
+static int qcom_snps_hsphy_init(struct phy *phy)
+{
+ struct hsphy_priv *priv = phy_get_drvdata(phy);
+ int state;
+ int ret;
+
+ ret = qcom_snps_hsphy_reset(priv);
+ if (ret)
+ return ret;
+
+ qcom_snps_hsphy_init_sequence(priv);
+
+ ret = qcom_snps_hsphy_por_reset(priv);
+ if (ret)
+ return ret;
+
+ /* Setup initial state */
+ if (priv->vbus_edev) {
+ state = extcon_get_state(priv->vbus_edev, EXTCON_USB);
+ ret = qcom_snps_hsphy_vbus_notifier(&priv->vbus_notify, state,
+ priv->vbus_edev);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct phy_ops qcom_snps_hsphy_ops = {
+ .init = qcom_snps_hsphy_init,
+ .power_on = qcom_snps_hsphy_power_on,
+ .power_off = qcom_snps_hsphy_power_off,
+ .set_mode = qcom_snps_hsphy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static const char * const qcom_snps_hsphy_clks[] = {
+ "ref",
+ "phy",
+ "sleep",
+};
+
+static int qcom_snps_hsphy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy_provider *provider;
+ struct hsphy_priv *priv;
+ struct resource *res;
+ struct phy *phy;
+ int size;
+ int ret;
+ int i;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->num_clks = ARRAY_SIZE(qcom_snps_hsphy_clks);
+ priv->clks = devm_kcalloc(dev, priv->num_clks, sizeof(*priv->clks),
+ GFP_KERNEL);
+ if (!priv->clks)
+ return -ENOMEM;
+
+ for (i = 0; i < priv->num_clks; i++)
+ priv->clks[i].id = qcom_snps_hsphy_clks[i];
+
+ ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
+ if (ret)
+ return ret;
+
+ priv->phy_reset = devm_reset_control_get(dev, "phy");
+ if (IS_ERR(priv->phy_reset))
+ return PTR_ERR(priv->phy_reset);
+
+ priv->por_reset = devm_reset_control_get(dev, "por");
+ if (IS_ERR(priv->por_reset))
+ return PTR_ERR(priv->por_reset);
+
+ priv->vregs[VDD].supply = "vdd";
+ priv->vregs[VDDA_1P8].supply = "vdda1p8";
+ priv->vregs[VDDA_3P3].supply = "vdda3p3";
+
+ ret = devm_regulator_bulk_get(dev, VREG_NUM, priv->vregs);
+ if (ret)
+ return ret;
+
+ priv->voltages[VDDA_1P8][VOL_NONE] = 0;
+ priv->voltages[VDDA_1P8][VOL_MIN] = 1800000;
+ priv->voltages[VDDA_1P8][VOL_MAX] = 1800000;
+
+ priv->voltages[VDDA_3P3][VOL_NONE] = 0;
+ priv->voltages[VDDA_3P3][VOL_MIN] = 3050000;
+ priv->voltages[VDDA_3P3][VOL_MAX] = 3300000;
+
+ ret = of_property_read_u32_array(dev->of_node, "qcom,vdd-voltage-level",
+ priv->voltages[VDD], VOL_NUM);
+ if (ret) {
+ dev_err(dev, "failed to read qcom,vdd-voltage-level\n");
+ return ret;
+ }
+
+ size = of_property_count_u32_elems(dev->of_node, "qcom,init-seq");
+ if (size < 0)
+ size = 0;
+
+ /*
+ * The init-seq is a sequence of tuple which consists of 3
+ * numbers <offset value delay>.
+ */
+ priv->init_seq = devm_kcalloc(dev, (size / 3) + 1,
+ sizeof(*priv->init_seq), GFP_KERNEL);
+ if (!priv->init_seq)
+ return -ENOMEM;
+
+ ret = of_property_read_u32_array(dev->of_node, "qcom,init-seq",
+ (u32 *) priv->init_seq, size);
+ if (ret && size)
+ return ret;
+
+ /* terminator */
+ priv->init_seq[size / 3].offset = -1;
+
+ phy = devm_phy_create(dev, dev->of_node, &qcom_snps_hsphy_ops);
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
+
+ priv->vbus_edev = extcon_get_edev_by_phandle(dev, 0);
+ if (IS_ERR(priv->vbus_edev)) {
+ if (PTR_ERR(priv->vbus_edev) != -ENODEV)
+ return PTR_ERR(priv->vbus_edev);
+ priv->vbus_edev = NULL;
+ }
+
+ if (priv->vbus_edev) {
+ priv->vbus_notify.notifier_call = qcom_snps_hsphy_vbus_notifier;
+ ret = devm_extcon_register_notifier(dev, priv->vbus_edev,
+ EXTCON_USB,
+ &priv->vbus_notify);
+ if (ret)
+ return ret;
+ }
+
+ phy_set_drvdata(phy, priv);
+
+ provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id qcom_snps_hsphy_match[] = {
+ { .compatible = "qcom,usb-snps-hsphy", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_match);
+
+static struct platform_driver qcom_snps_hsphy_driver = {
+ .probe = qcom_snps_hsphy_probe,
+ .driver = {
+ .name = "qcom-usb-snps-hsphy",
+ .of_match_table = qcom_snps_hsphy_match,
+ },
+};
+module_platform_driver(qcom_snps_hsphy_driver);
+
+MODULE_DESCRIPTION("Qualcomm Synopsys 28nm USB High-Speed PHY driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
^ permalink raw reply related [flat|nested] 3+ messages in thread