[PATCH 1/3] dt-bindings: Add vendor prefix for Smartlabs

[PATCH 1/3] dt-bindings: Add vendor prefix for Smartlabs

[Christian Hewitt]

Smartlabs are a professional integrator of Interactive TV solutions
and IPTV/VOD devices.

[1] (https://www.smartlabs.tv/en/about/)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8..4e087f9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -357,6 +357,7 @@ sirf	SiRF Technology, Inc.
 sis	Silicon Integrated Systems Corp.
 sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
+smartlabs	Smartlabs
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
 socionext	Socionext Inc.
-- 
2.7.4

[PATCH 2/3] dt-bindings: arm: amlogic: Add support for the Smartlabs SML-5442TW

[Christian Hewitt]

The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-S based on the
Amlogic P231 reference design using the S905D chipset. Specs:

2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377)
2x single colour and 1x dual colour LEDs on the front panel
1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack
S/PDIF audio output
Single DVB-S tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 4498292..ad79f2d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -91,6 +91,7 @@ Board compatible values (alphabetically, grouped by SoC):
 
   - "amlogic,p230" (Meson gxl s905d)
   - "amlogic,p231" (Meson gxl s905d)
+  - "smartlabs,sml5442tw" (Meson gxl s905d)
 
   - "amlogic,p241" (Meson gxl s805x)
 
-- 
2.7.4

[PATCH 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[Christian Hewitt]

The Smartlabs SML-5442TW is broadly similar to the P231 reference design
but with the following differences:

- Yellow and Blue front-panel LEDs are available but disabled
- Red/Green LED is used to signal off/on status
- GPIOX_17 is set high to enable the QCA9377 wireless module
- uart_AO can be accessed after opening the case; soldered pins exist

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 327 +++++++++++++++++++++
 2 files changed, 328 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index c31f29d6..37d7dbd 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
new file mode 100644
index 0000000..4b40a71
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+	compatible = "smartlabs,sml5442tw", "amlogic,s905d", "amlogic,meson-gxl";
+	model = "Smartlabs SML-5442TW";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		yellow {
+			label = "sml5442tw:yellow";
+			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		blue {
+			label = "sml5442tw:blue";
+			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		green {
+			label = "sml5442tw:green";
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		red {
+			label = "sml5442tw:red";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "HDMI";
+
+		simple-audio-card,dai-link@0 {
+			/* HDMI Output */
+			format = "i2s";
+			mclk-fs = <128>;
+			bitclock-master =  <&i2s_dai>;
+			frame-master = <&i2s_dai>;
+			plat {
+				sound-dai = <&aiu_i2s_dma>;
+			};
+
+			cpu {
+				sound-dai = <&i2s_dai>;
+			};
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&audio {
+	status = "okay";
+};
+
+&aiu_i2s_dma {
+	status = "okay";
+};
+
+&i2s_dai {
+	status = "okay";
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+/* This will enable the bluetooth module */
+&gpio {
+	bt-en {
+		gpio-hog;
+		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bt-en";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+	linux,rc-map-name = "rc-o2cz-khamsin";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+};
+
+/* This UART is brought out to the debug header */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
-- 
2.7.4

Re: [PATCH 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[jbrunet]

On Thu, 2018-11-08 at 19:33 +0400, Christian Hewitt wrote:
> 
> +&audio {
> +	status = "okay";
> +};
> +
> +&aiu_i2s_dma {
> +	status = "okay";
> +};
> +
> +&i2s_dai {
> +	status = "okay";
> +};

The audio stuff has not made it's way upstream (yet) please drop this

> +
> +&cvbs_vdac_port {
> +	cvbs_vdac_out: endpoint {
> +		remote-endpoint = <&cvbs_connector_in>;
> +	};
> +};
> +
> 
[ ... ]

> +
> +/* This is connected to the Bluetooth module: */
> +&uart_A {
> +	status = "okay";
> +	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> +	pinctrl-names = "default";

Did you forget to put 'uart-has-rtscts;' here ?

> +};
> +
> +/* This UART is brought out to the debug header */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};

Also, you sent a multipatch series. Such patchset should start with a cover
letter describing the general intent ... even if it is obvious.

Re: [PATCH 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[kbuild test robot]

[-- Attachment #1: Type: text/plain, Size: 1402 bytes --]

Hi Christian,

Thank you for the patch! Yet something to improve:

[auto build test ERROR on robh/for-next]
[also build test ERROR on v4.20-rc1 next-20181108]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]

url:    https://github.com/0day-ci/linux/commits/Christian-Hewitt/dt-bindings-Add-vendor-prefix-for-Smartlabs/20181109-010512
base:   https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
config: arm64-allyesconfig (attached as .config)
compiler: aarch64-linux-gnu-gcc (Debian 7.2.0-11) 7.2.0
reproduce:
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # save the attached .config to linux build tree
        GCC_VERSION=7.2.0 make.cross ARCH=arm64 

All errors (new ones prefixed by >>):

>> Error: arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts:172.1-7 Label or path audio not found
>> Error: arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts:176.1-13 Label or path aiu_i2s_dma not found
>> Error: arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts:180.1-9 Label or path i2s_dai not found
   FATAL ERROR: Syntax error parsing input tree

---
0-DAY kernel test infrastructure                Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all                   Intel Corporation

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 61776 bytes --]

[PATCH v2 0/3] ARM64: dts: meson-gxl: Add dts and bindings for Smartlabs SML-5442TW

[Christian Hewitt]

This series adds new bindings and a device-tree file for the Smartlabs
SML-5442TW set-top box.

v2 - removed audio nodes
   - changes soundcard name to "meson-gx-audio"
   - added missing uart-has-rtscts;

Christian Hewitt (3):
  dt-bindings: Add vendor prefix for Smartlabs
  dt-bindings: arm: amlogic: Add support for the Smartlabs SML-5442TW
  ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

 Documentation/devicetree/bindings/arm/amlogic.txt  |   1 +
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 316 +++++++++++++++++++++
 4 files changed, 319 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts

-- 
2.7.4

[PATCH v2 1/3] dt-bindings: Add vendor prefix for Smartlabs

[Christian Hewitt]

Smartlabs are a professional integrator of Interactive TV solutions
and IPTV/VOD devices.

[1] (https://www.smartlabs.tv/en/about/)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8..4e087f9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -357,6 +357,7 @@ sirf	SiRF Technology, Inc.
 sis	Silicon Integrated Systems Corp.
 sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
+smartlabs	Smartlabs
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
 socionext	Socionext Inc.
-- 
2.7.4

Re: [PATCH v2 1/3] dt-bindings: Add vendor prefix for Smartlabs

[Andreas Färber]

Am 08.11.18 um 18:01 schrieb Christian Hewitt:
> Smartlabs are a professional integrator of Interactive TV solutions
> and IPTV/VOD devices.
> 
> [1] (https://www.smartlabs.tv/en/about/)

"[1]" is not referenced anywhere, so you could just as well use a plain
link?

> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 4b1a2a8..4e087f9 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -357,6 +357,7 @@ sirf	SiRF Technology, Inc.
>  sis	Silicon Integrated Systems Corp.
>  sitronix	Sitronix Technology Corporation
>  skyworks	Skyworks Solutions, Inc.
> +smartlabs	Smartlabs

"SmartLabs LLC" according to your link above!

Otherwise looks okay.

Regards,
Andreas

>  smsc	Standard Microsystems Corporation
>  snps	Synopsys, Inc.
>  socionext	Socionext Inc.
> 


-- 
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Graham Norton
HRB 21284 (AG Nürnberg)

[PATCH v2 2/3] dt-bindings: arm: amlogic: Add support for the Smartlabs SML-5442TW

[Christian Hewitt]

The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-S based on the
Amlogic P231 reference design using the S905D chipset. Specs:

2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377)
2x single colour and 1x dual colour LEDs on the front panel
1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack
S/PDIF audio output
Single DVB-S tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 4498292..ad79f2d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -91,6 +91,7 @@ Board compatible values (alphabetically, grouped by SoC):
 
   - "amlogic,p230" (Meson gxl s905d)
   - "amlogic,p231" (Meson gxl s905d)
+  - "smartlabs,sml5442tw" (Meson gxl s905d)
 
   - "amlogic,p241" (Meson gxl s805x)
 
-- 
2.7.4

[PATCH v2 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[Christian Hewitt]

The Smartlabs SML-5442TW is broadly similar to the P231 reference design
but with the following differences:

- Yellow and Blue front-panel LEDs are available but disabled
- Red/Green LED is used to signal off/on status
- GPIOX_17 is set high to enable the QCA9377 wireless module
- uart_AO can be accessed after opening the case; soldered pins exist

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 316 +++++++++++++++++++++
 2 files changed, 317 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index c31f29d6..37d7dbd 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
new file mode 100644
index 0000000..a081984
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
@@ -0,0 +1,316 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+	compatible = "smartlabs,sml5442tw", "amlogic,s905d", "amlogic,meson-gxl";
+	model = "Smartlabs SML-5442TW";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		yellow {
+			label = "sml5442tw:yellow";
+			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		blue {
+			label = "sml5442tw:blue";
+			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		green {
+			label = "sml5442tw:green";
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		red {
+			label = "sml5442tw:red";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "meson-gx-audio";
+
+		simple-audio-card,dai-link@0 {
+			/* HDMI Output */
+			format = "i2s";
+			mclk-fs = <256>;
+			bitclock-master =  <&i2s_dai>;
+			frame-master = <&i2s_dai>;
+			plat {
+				sound-dai = <&aiu_i2s_dma>;
+			};
+
+			cpu {
+				sound-dai = <&i2s_dai>;
+			};
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+/* This will enable the bluetooth module */
+&gpio {
+	bt-en {
+		gpio-hog;
+		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bt-en";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+	linux,rc-map-name = "rc-o2cz-khamsin";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+/* This UART is brought out to the debug header */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
-- 
2.7.4

Re: [PATCH v2 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[jbrunet]

On Thu, 2018-11-08 at 21:01 +0400, Christian Hewitt wrote:
> The Smartlabs SML-5442TW is broadly similar to the P231 reference design
> but with the following differences:
> 
> - Yellow and Blue front-panel LEDs are available but disabled
> - Red/Green LED is used to signal off/on status
> - GPIOX_17 is set high to enable the QCA9377 wireless module
> - uart_AO can be accessed after opening the case; soldered pins exist
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile               |   1 +
>  .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 316
> +++++++++++++++++++++
>  2 files changed, 317 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-
> sml5442tw.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile
> b/arch/arm64/boot/dts/amlogic/Makefile
> index c31f29d6..37d7dbd 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-
> a95x.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
> b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
> new file mode 100644
> index 0000000..a081984
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
> @@ -0,0 +1,316 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2016 Endless Computers, Inc.
> + * Author: Carlo Caione <carlo@endlessm.com>
> + * Copyright (c) 2018 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-gxl-s905d.dtsi"
> +
> +/ {
> +	compatible = "smartlabs,sml5442tw", "amlogic,s905d", "amlogic,meson-
> gxl";
> +	model = "Smartlabs SML-5442TW";
> +
> +	aliases {
> +		serial0 = &uart_AO;
> +		serial1 = &uart_A;
> +		ethernet0 = &ethmac;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x80000000>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		yellow {
> +			label = "sml5442tw:yellow";
> +			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		blue {
> +			label = "sml5442tw:blue";
> +			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		green {
> +			label = "sml5442tw:green";
> +			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +
> +		red {
> +			label = "sml5442tw:red";
> +			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	hdmi_5v: regulator-hdmi-5v {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "HDMI_5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +
> +		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	cvbs-connector {
> +		compatible = "composite-video-connector";
> +
> +		port {
> +			cvbs_connector_in: endpoint {
> +				remote-endpoint = <&cvbs_vdac_out>;
> +			};
> +		};
> +	};
> +
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&hdmi_tx_tmds_out>;
> +			};
> +		};
> +	};
> +
> +	sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "meson-gx-audio";
> +
> +		simple-audio-card,dai-link@0 {
> +			/* HDMI Output */
> +			format = "i2s";
> +			mclk-fs = <256>;
> +			bitclock-master =  <&i2s_dai>;
> +			frame-master = <&i2s_dai>;
> +			plat {
> +				sound-dai = <&aiu_i2s_dma>;
> +			};
> +
> +			cpu {
> +				sound-dai = <&i2s_dai>;
> +			};
> +
> +			codec {
> +				sound-dai = <&hdmi_tx>;
> +			};
> +		};
> +	};
> +};

Still not good, sorry !

> +
> +&cec_AO {
> +	status = "okay";
> +	pinctrl-0 = <&ao_cec_pins>;
> +	pinctrl-names = "default";
> +	hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cvbs_vdac_port {
> +	cvbs_vdac_out: endpoint {
> +		remote-endpoint = <&cvbs_connector_in>;
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +	phy-mode = "rmii";
> +	phy-handle = <&internal_phy>;
> +};
> +
> +/* This will enable the bluetooth module */
> +&gpio {
> +	bt-en {
> +		gpio-hog;
> +		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "bt-en";
> +	};
> +};
> +
> +&hdmi_tx {
> +	status = "okay";
> +	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> +	pinctrl-names = "default";
> +	hdmi-supply = <&hdmi_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> +	hdmi_tx_tmds_out: endpoint {
> +		remote-endpoint = <&hdmi_connector_in>;
> +	};
> +};
> +
> +&i2c_A {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&internal_phy {
> +	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&ir {
> +	status = "okay";
> +	pinctrl-0 = <&remote_input_ao_pins>;
> +	pinctrl-names = "default";
> +	linux,rc-map-name = "rc-o2cz-khamsin";
> +};
> +
> +&pwm_ef {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_e_pins>;
> +	pinctrl-names = "default";
> +	clocks = <&clkc CLKID_FCLK_DIV4>;
> +	clock-names = "clkin0";
> +};
> +
> +&saradc {
> +	status = "okay";
> +	vref-supply = <&vddio_ao18>;
> +};
> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> +	status = "okay";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +
> +	non-removable;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> +	status = "okay";
> +	pinctrl-0 = <&sdcard_pins>;
> +	pinctrl-1 = <&sdcard_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +	disable-wp;
> +
> +	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> +	cd-inverted;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <100000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* This is connected to the Bluetooth module: */
> +&uart_A {
> +	status = "okay";
> +	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +};
> +
> +/* This UART is brought out to the debug header */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};

[PATCH v3 0/3] ARM64: dts: meson-gxl: Add dts and bindings for Smartlabs SML-5442TW

[Christian Hewitt]

This series adds new bindings and a device-tree file for the Smartlabs
SML-5442TW set-top box.

v3 - change to Smartlabs LLC
   - removed sound node
v2 - removed audio nodes
   - changes soundcard name to "meson-gx-audio"
   - added missing uart-has-rtscts;

Christian Hewitt (3):
  dt-bindings: Add vendor prefix for Smartlabs LLC
  dt-bindings: arm: amlogic: Add support for the Smartlabs SML-5442TW
  ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

 Documentation/devicetree/bindings/arm/amlogic.txt  |   1 +
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 4 files changed, 295 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts

-- 
2.7.4

[PATCH v3 1/3] dt-bindings: Add vendor prefix for Smartlabs LLC

[Christian Hewitt]

Smartlabs LLC are a professional integrator of Interactive TV solutions
and IPTV/VOD devices (https://www.smartlabs.tv/en/about/).

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 4b1a2a8..c424fe0 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -357,6 +357,7 @@ sirf	SiRF Technology, Inc.
 sis	Silicon Integrated Systems Corp.
 sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
+smartlabs	Smartlabs LLC
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
 socionext	Socionext Inc.
-- 
2.7.4

Re: [PATCH v3 1/3] dt-bindings: Add vendor prefix for Smartlabs LLC

[Andreas Färber]

Am 08.11.18 um 20:43 schrieb Christian Hewitt:
> Smartlabs LLC are a professional integrator of Interactive TV solutions
> and IPTV/VOD devices (https://www.smartlabs.tv/en/about/).
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 4b1a2a8..c424fe0 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -357,6 +357,7 @@ sirf	SiRF Technology, Inc.
>  sis	Silicon Integrated Systems Corp.
>  sitronix	Sitronix Technology Corporation
>  skyworks	Skyworks Solutions, Inc.
> +smartlabs	Smartlabs LLC

You added the LLC but did not upper-case the L - intentional?

Regards,
Andreas

>  smsc	Standard Microsystems Corporation
>  snps	Synopsys, Inc.
>  socionext	Socionext Inc.
> 


-- 
SUSE Linux GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer, Jane Smithard, Graham Norton
HRB 21284 (AG Nürnberg)

Re: [PATCH v3 1/3] dt-bindings: Add vendor prefix for Smartlabs LLC

[Christian Hewitt]

On 9 Nov 2018, at 1:29 pm, Andreas Färber <afaerber@suse.de> wrote:
> 
>> Smartlabs LLC are a professional integrator of Interactive TV solutions
>> and IPTV/VOD devices (https://www.smartlabs.tv/en/about/).
>> 
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
>> 1 file changed, 1 insertion(+)
>> 
>> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> index 4b1a2a8..c424fe0 100644
>> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
>> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
>> @@ -357,6 +357,7 @@ sirf	SiRF Technology, Inc.
>> sis	Silicon Integrated Systems Corp.
>> sitronix	Sitronix Technology Corporation
>> skyworks	Skyworks Solutions, Inc.
>> +smartlabs	Smartlabs LLC
> 
> You added the LLC but did not upper-case the L - intentional?

Not intentional. I’ll correct this (and another mention in the dts) in v4.

Christian

[PATCH v3 2/3] dt-bindings: arm: amlogic: Add support for the Smartlabs SML-5442TW

[Christian Hewitt]

The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-S based on the
Amlogic P231 reference design using the S905D chipset. Specs:

2GB DDR3 RAM
8GB eMMC storage
10/100 Base-T Ethernet
802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377)
2x single colour and 1x dual colour LEDs on the front panel
1x reset button on the front panel
HDMI 2.0 (4k@60p) video
Composite video + 2-channel audio output on 3.5mm jack
S/PDIF audio output
Single DVB-S tuner (AVL6762/MxL608)
2x USB 2.0 ports
1x micro SD card slot
UART pins (internal)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 4498292..ad79f2d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -91,6 +91,7 @@ Board compatible values (alphabetically, grouped by SoC):
 
   - "amlogic,p230" (Meson gxl s905d)
   - "amlogic,p231" (Meson gxl s905d)
+  - "smartlabs,sml5442tw" (Meson gxl s905d)
 
   - "amlogic,p241" (Meson gxl s805x)
 
-- 
2.7.4

Re: [PATCH v3 2/3] dt-bindings: arm: amlogic: Add support for the Smartlabs SML-5442TW

[Rob Herring]

On Thu,  8 Nov 2018 23:43:52 +0400, Christian Hewitt wrote:
> The SML-5442TW is an STB for O2 Czech IPTV/VOD and DVB-S based on the
> Amlogic P231 reference design using the S905D chipset. Specs:
> 
> 2GB DDR3 RAM
> 8GB eMMC storage
> 10/100 Base-T Ethernet
> 802.11 a/b/g/n/ac + BT 4.1 HS sdio wireless module (QCA9377)
> 2x single colour and 1x dual colour LEDs on the front panel
> 1x reset button on the front panel
> HDMI 2.0 (4k@60p) video
> Composite video + 2-channel audio output on 3.5mm jack
> S/PDIF audio output
> Single DVB-S tuner (AVL6762/MxL608)
> 2x USB 2.0 ports
> 1x micro SD card slot
> UART pins (internal)
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  Documentation/devicetree/bindings/arm/amlogic.txt | 1 +
>  1 file changed, 1 insertion(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v3 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[Christian Hewitt]

The Smartlabs SML-5442TW is broadly similar to the P231 reference design
but with the following differences:

- Yellow and Blue front-panel LEDs are available but disabled
- Red/Green LED is used to signal off/on status
- GPIOX_17 is set high to enable the QCA9377 wireless module
- uart_AO can be accessed after opening the case; soldered pins exist

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 2 files changed, 293 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index c31f29d6..37d7dbd 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
new file mode 100644
index 0000000..44d02c2
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+	compatible = "smartlabs,sml5442tw", "amlogic,s905d", "amlogic,meson-gxl";
+	model = "Smartlabs SML-5442TW";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		yellow {
+			label = "sml5442tw:yellow";
+			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		blue {
+			label = "sml5442tw:blue";
+			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		green {
+			label = "sml5442tw:green";
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		red {
+			label = "sml5442tw:red";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+/* This will enable the bluetooth module */
+&gpio {
+	bt-en {
+		gpio-hog;
+		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bt-en";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+	linux,rc-map-name = "rc-o2cz-khamsin";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+/* This UART is brought out to the debug header */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
-- 
2.7.4

Re: [PATCH v3 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[Neil Armstrong]

Hi Christian,

On 08/11/2018 20:43, Christian Hewitt wrote:
> The Smartlabs SML-5442TW is broadly similar to the P231 reference design
> but with the following differences:
> 
> - Yellow and Blue front-panel LEDs are available but disabled
> - Red/Green LED is used to signal off/on status
> - GPIOX_17 is set high to enable the QCA9377 wireless module
> - uart_AO can be accessed after opening the case; soldered pins exist
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile               |   1 +
>  .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
>  2 files changed, 293 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index c31f29d6..37d7dbd 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
> new file mode 100644
> index 0000000..44d02c2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
> @@ -0,0 +1,292 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2016 Endless Computers, Inc.
> + * Author: Carlo Caione <carlo@endlessm.com>
> + * Copyright (c) 2018 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +

[...]

> +
> +&usb0 {
> +	status = "okay";
> +};
> 

It's ok for me !

Acked-by: Neil Armstrong <narmstrong@baylibre.com>

Neil

Re: [PATCH v3 3/3] ARM64: dts: meson-gxl: Add support for the Smartlabs SML-5442TW

[jbrunet]

On Thu, 2018-11-08 at 23:43 +0400, Christian Hewitt wrote:
> +/* This will enable the bluetooth module */
> +&gpio {
> +       bt-en {
> +               gpio-hog;
> +               gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
> +               output-high;
> +               line-name = "bt-en";
> +       };
> +};

Instead of this, is it possible to use the driver provided by
drivers/bluetooth/hci_qca.c ?