[PATCHv5 0/6] Add support for UHS-I on Exynos5422 odroid boards

[PATCHv5 0/6] Add support for UHS-I on Exynos5422 odroid boards

[Anand Moon]

This is series v4 since my previous patches were incomplete with driver
changes missing.

v5 changes.
drop the cd-gpios wp-gpio gpio pin setting, just add the pinctrl
configration to support write protect.

v4 changes.
squash cd-gpios and wp-gpio changes into single patch.
change the subject prefix to "ARM: dts: exynos:"

These changes add UHS-I tuning for dw_mmc-exynos driver.

Rebased on Krzysztof branch next/dt
[0] git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux.git 

Anand Moon (6):
  ARM: dts: exynos: Added UHS-I bus speed support
  ARM: dts: exynos: fix regulator min values of LDO13 for Odroid XU3/XU4
  ARM: dts: exynos: update maximum frequency for sdcard to 200MHz
  ARM: dts: exynos: Add pin configuration for SD write protect on Odroid
    XU3/XU4
  ARM: dts: exynos: update maximum frequency for emmc to 200MHz
  mmc: dw_mmc-exynos: Add tuning for sdr and ddr timing for USH-I mode

 arch/arm/boot/dts/exynos5420-pinctrl.dtsi          |  7 +++++++
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi      |  8 ++++++--
 arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi |  1 +
 drivers/mmc/host/dw_mmc-exynos.c                   | 11 +++++++++++
 4 files changed, 25 insertions(+), 2 deletions(-)

-- 
2.17.1

[PATCHv5 1/6] ARM: dts: exynos: Added UHS-I bus speed support

[Anand Moon]

Added support for UHS-I bus speed tuning for SDR50, DDR50 SDR104.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
---
[0] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-October/376263.html
Changes from above.
Fix the subject and commit message.
drop sd-uhs-sdr12 and sd-uhs-sdr25 as host driver is not enable as of now.
---
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index 2fac4baf1eb4..0508e6891f41 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -503,6 +503,9 @@
 	cap-sd-highspeed;
 	vmmc-supply = <&ldo19_reg>;
 	vqmmc-supply = <&ldo13_reg>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
 };
 
 &nocp_mem0_0 {
-- 
2.17.1

[PATCHv5 2/6] ARM: dts: exynos: fix regulator min values of LDO13 for Odroid XU3/XU4

[Anand Moon]

Looking at the schematic sd_2 min/max range from 1.8V/2.8V so fix the
regulator min value to 1.8V. Without these changes sdcard will failed
to detect on booting when UHS-I tuning is enabled.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
[0] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-October/376262.html
Fixed the commit message.
drop the ramp-delay changes.
drop the vmmc-supply/vqmmc-supply changes.
---
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index 0508e6891f41..15ab380e5fcf 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -231,7 +231,7 @@
 
 			ldo13_reg: LDO13 {
 				regulator-name = "vddq_mmc2";
-				regulator-min-microvolt = <2800000>;
+				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <2800000>;
 			};
 
-- 
2.17.1

[PATCHv5 3/6] ARM: dts: exynos: update maximum frequency for sdcard to 200MHz

[Anand Moon]

set the max-frequency to 200MHz for optimal performace.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
This patch is new to this series.

microSD card.
root@odroid:~# sudo cat /sys/kernel/debug/mmc1/ios
clock:          200000000 Hz
actual clock:   200000000 Hz
vdd:            16 (2.8 ~ 2.9 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      2 (4 bits)
timing spec:    6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type:    0 (driver type B)
---
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index 15ab380e5fcf..a80b6c045154 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -501,6 +501,7 @@
 	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
 	bus-width = <4>;
 	cap-sd-highspeed;
+	max-frequency = <200000000>;
 	vmmc-supply = <&ldo19_reg>;
 	vqmmc-supply = <&ldo13_reg>;
 	sd-uhs-sdr50;
-- 
2.17.1

[PATCHv5 4/6] ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4

[Anand Moon]

Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.

Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
Changes since v4:
1. Remove cd-gpios and wp-gpios leaving only WP pin configuration (after
   Marek Szyprowski feedback).
2. Pull pin down.
3. change the subject and commit message.
Sorry Krzysztof if I have copied your commit message to describe the
changes.
---
 arch/arm/boot/dts/exynos5420-pinctrl.dtsi     | 7 +++++++
 arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 2 +-
 2 files changed, 8 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
index dda8ca2d2324..b82af7c89654 100644
--- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
@@ -289,6 +289,13 @@
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
+
+	sd2_wp: sd2-wp {
+		samsung,pins = "gpc4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
 };
 
 &pinctrl_2 {
diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index a80b6c045154..54811960e322 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -498,7 +498,7 @@
 	samsung,dw-mshc-sdr-timing = <0 4>;
 	samsung,dw-mshc-ddr-timing = <0 2>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_wp &sd2_bus1 &sd2_bus4>;
 	bus-width = <4>;
 	cap-sd-highspeed;
 	max-frequency = <200000000>;
-- 
2.17.1

[PATCHv5 5/6] ARM: dts: exynos: update maximum frequency for emmc to 200MHz

[Anand Moon]

Set the max-frequency to 200MHz for optimal performace of eMMC.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
eMMC

root@odroid:~# sudo cat /sys/kernel/debug/mmc0/ios
clock:          200000000 Hz
actual clock:   200000000 Hz
vdd:            7 (1.65 - 1.95 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      3 (8 bits)
timing spec:    10 (mmc HS400)
signal voltage: 1 (1.80 V)
driver type:    0 (driver type B)
---
 arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
index e522edb2bb82..1f2d3987dde1 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -392,6 +392,7 @@
 	cap-mmc-highspeed;
 	mmc-hs200-1_8v;
 	mmc-hs400-1_8v;
+	max-frequency = <200000000>;
 	vmmc-supply = <&ldo18_reg>;
 	vqmmc-supply = <&ldo3_reg>;
 };
-- 
2.17.1

[PATCHv5 6/6] mmc: dw_mmc-exynos: Add tuning for sdr and ddr timing for USH-I mode

[Anand Moon]

Add tuning for sdr and ddr timing for USH-I mode sdr104/sdr50/ddr50
for host controller.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
No changes from previous patch
---
 drivers/mmc/host/dw_mmc-exynos.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/mmc/host/dw_mmc-exynos.c b/drivers/mmc/host/dw_mmc-exynos.c
index ab47b018716a..d46c3439b508 100644
--- a/drivers/mmc/host/dw_mmc-exynos.c
+++ b/drivers/mmc/host/dw_mmc-exynos.c
@@ -253,6 +253,8 @@ static void dw_mci_exynos_config_hs400(struct dw_mci *host, u32 timing)
 	if (timing == MMC_TIMING_MMC_HS400) {
 		dqs |= DATA_STROBE_EN;
 		strobe = DQS_CTRL_RD_DELAY(strobe, priv->dqs_delay);
+	} else if (timing == MMC_TIMING_UHS_SDR104) {
+		dqs &= 0xffffff00;
 	} else {
 		dqs &= ~DATA_STROBE_EN;
 	}
@@ -312,6 +314,15 @@ static void dw_mci_exynos_set_ios(struct dw_mci *host, struct mmc_ios *ios)
 		if (ios->bus_width == MMC_BUS_WIDTH_8)
 			wanted <<= 1;
 		break;
+	case MMC_TIMING_UHS_SDR104:
+	case MMC_TIMING_UHS_SDR50:
+		clksel = (priv->sdr_timing & 0xfff8ffff) |
+			(priv->ciu_div << 16);
+		break;
+	case MMC_TIMING_UHS_DDR50:
+		clksel = (priv->ddr_timing & 0xfff8ffff) |
+			(priv->ciu_div << 16);
+		break;
 	default:
 		clksel = priv->sdr_timing;
 	}
-- 
2.17.1

Re: [PATCHv5 0/6] Add support for UHS-I on Exynos5422 odroid boards

[Ulf Hansson]

On 27 September 2018 at 16:07, Anand Moon <linux.amoon@gmail.com> wrote:
> This is series v4 since my previous patches were incomplete with driver
> changes missing.
>
> v5 changes.
> drop the cd-gpios wp-gpio gpio pin setting, just add the pinctrl
> configration to support write protect.
>
> v4 changes.
> squash cd-gpios and wp-gpio changes into single patch.
> change the subject prefix to "ARM: dts: exynos:"
>
> These changes add UHS-I tuning for dw_mmc-exynos driver.
>
> Rebased on Krzysztof branch next/dt
> [0] git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux.git
>
> Anand Moon (6):
>   ARM: dts: exynos: Added UHS-I bus speed support
>   ARM: dts: exynos: fix regulator min values of LDO13 for Odroid XU3/XU4
>   ARM: dts: exynos: update maximum frequency for sdcard to 200MHz
>   ARM: dts: exynos: Add pin configuration for SD write protect on Odroid
>     XU3/XU4
>   ARM: dts: exynos: update maximum frequency for emmc to 200MHz
>   mmc: dw_mmc-exynos: Add tuning for sdr and ddr timing for USH-I mode
>
>  arch/arm/boot/dts/exynos5420-pinctrl.dtsi          |  7 +++++++
>  arch/arm/boot/dts/exynos5422-odroid-core.dtsi      |  8 ++++++--
>  arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi |  1 +
>  drivers/mmc/host/dw_mmc-exynos.c                   | 11 +++++++++++
>  4 files changed, 25 insertions(+), 2 deletions(-)
>
> --
> 2.17.1
>

Anand,

I have applied the mmc patch for next, thanks!

In regards to the DTS changes, I assume the soc maintainers will pick
them up, but maybe you need to resend them separately.

Kind regards
Uffe

Re: [PATCHv5 1/6] ARM: dts: exynos: Added UHS-I bus speed support

[Krzysztof Kozlowski]

On Thu, Sep 27, 2018 at 02:07:33PM +0000, Anand Moon wrote:
> Added support for UHS-I bus speed tuning for SDR50, DDR50 SDR104.
> 

Thanks, applied.

Best regards,
Krzysztof

Re: [PATCHv5 2/6] ARM: dts: exynos: fix regulator min values of LDO13 for Odroid XU3/XU4

[Krzysztof Kozlowski]

On Thu, Sep 27, 2018 at 02:07:34PM +0000, Anand Moon wrote:
> Looking at the schematic sd_2 min/max range from 1.8V/2.8V so fix the
> regulator min value to 1.8V. Without these changes sdcard will failed
> to detect on booting when UHS-I tuning is enabled.
> 

Thanks, applied.

Best regards,
Krzysztof

Re: [PATCHv5 3/6] ARM: dts: exynos: update maximum frequency for sdcard to 200MHz

[Krzysztof Kozlowski]

On Thu, Sep 27, 2018 at 02:07:35PM +0000, Anand Moon wrote:
> set the max-frequency to 200MHz for optimal performace.
> 

Thanks, applied.

Best regards,
Krzysztof

Re: [PATCHv5 5/6] ARM: dts: exynos: update maximum frequency for emmc to 200MHz

[Krzysztof Kozlowski]

On Thu, Sep 27, 2018 at 02:07:37PM +0000, Anand Moon wrote:
> Set the max-frequency to 200MHz for optimal performace of eMMC.
> 

Thanks, applied.

Best regards,
Krzysztof

Re: [PATCHv5 4/6] ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4

[Krzysztof Kozlowski]

On Thu, Sep 27, 2018 at 02:07:36PM +0000, Anand Moon wrote:
> Add SD card write-protect pin configuration to be sure that it will be
> properly pulled down to indicate write access.
> 
> Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
> Changes since v4:
> 1. Remove cd-gpios and wp-gpios leaving only WP pin configuration (after
>    Marek Szyprowski feedback).
> 2. Pull pin down.
> 3. change the subject and commit message.
> Sorry Krzysztof if I have copied your commit message to describe the
> changes.

Thanks, applied.

Best regards,
Krzysztof