From: Rajendra Nayak <rnayak@codeaurora.org>
To: robh@kernel.org, viresh.kumar@linaro.org, sboyd@kernel.org,
andy.gross@linaro.org, ulf.hansson@linaro.org,
collinsd@codeaurora.org, mka@chromium.org
Cc: devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org,
Rajendra Nayak <rnayak@codeaurora.org>
Subject: [PATCH v5 7/8] arm64: dts: sdm845: Add rpmh powercontroller node
Date: Tue, 4 Dec 2018 10:51:18 +0530 [thread overview]
Message-ID: <20181204052119.806-8-rnayak@codeaurora.org> (raw)
In-Reply-To: <20181204052119.806-1-rnayak@codeaurora.org>
Add the DT node for the rpmhpd powercontroller.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
---
arch/arm64/boot/dts/qcom/sdm845.dtsi | 51 ++++++++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index b72bdb0a31a5..a6d0cd8d17b0 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/phy/phy-qcom-qusb2.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/reset/qcom,sdm845-aoss.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -1324,6 +1325,56 @@
compatible = "qcom,sdm845-rpmh-clk";
#clock-cells = <1>;
};
+
+ rpmhpd: power-controller {
+ compatible = "qcom,sdm845-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+ };
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2-qcom-level";
+
+ rpmhpd_opp_ret: opp1 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ qcom,level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
};
intc: interrupt-controller@17a00000 {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2018-12-04 5:22 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-04 5:21 [PATCH v5 0/8] Add power domain driver for corners on msm8996/sdm845 Rajendra Nayak
2018-12-04 5:21 ` [PATCH v5 1/8] dt-bindings: opp: Introduce qcom-opp bindings Rajendra Nayak
2018-12-04 23:06 ` Stephen Boyd
2018-12-07 17:29 ` Rob Herring
2018-12-04 5:21 ` [PATCH v5 2/8] dt-bindings: power: Add qcom rpm power domain driver bindings Rajendra Nayak
2018-12-04 5:21 ` [PATCH v5 3/8] soc: qcom: rpmpd: Add a Power domain driver to model corners Rajendra Nayak
2018-12-04 23:12 ` Stephen Boyd
2018-12-05 7:01 ` Rajendra Nayak
2018-12-04 5:21 ` [PATCH v5 4/8] soc: qcom: rpmpd: Add support for get/set performance state Rajendra Nayak
2018-12-04 23:14 ` Stephen Boyd
2018-12-05 7:03 ` Rajendra Nayak
2018-12-05 10:11 ` Rajendra Nayak
2018-12-05 20:46 ` Stephen Boyd
2018-12-04 5:21 ` [PATCH v5 5/8] arm64: dts: msm8996: Add rpmpd device node Rajendra Nayak
2018-12-04 5:21 ` [PATCH v5 6/8] soc: qcom: rpmhpd: Add RPMh Power domain driver Rajendra Nayak
2018-12-04 5:21 ` Rajendra Nayak [this message]
2018-12-04 5:25 ` [PATCH v5 7/8] arm64: dts: sdm845: Add rpmh powercontroller node Viresh Kumar
2018-12-04 23:16 ` Stephen Boyd
2018-12-05 7:07 ` Rajendra Nayak
2018-12-07 17:36 ` Rob Herring
2018-12-04 5:21 ` [PATCH v5 8/8] soc: qcom: rpmhpd: Mark mx as a parent for cx Rajendra Nayak
2018-12-04 5:26 ` Viresh Kumar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181204052119.806-8-rnayak@codeaurora.org \
--to=rnayak@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=collinsd@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).