* [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema
@ 2019-01-10 22:20 Rob Herring
2019-01-10 22:20 ` [PATCH 2/2] dt-bindings: serial: Move renesas,rzn1-uart into the snps-dw-apb-uart binding Rob Herring
2019-01-14 9:30 ` [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Simon Horman
0 siblings, 2 replies; 6+ messages in thread
From: Rob Herring @ 2019-01-10 22:20 UTC (permalink / raw)
To: devicetree; +Cc: linux-kernel, Greg Kroah-Hartman, linux-serial
Convert the snps,dw-apb-uart binding to DT schema using json-schema.
The Rockchip and Broadcom compatible strings were not documented,
so add them here.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
.../bindings/serial/snps-dw-apb-uart.txt | 76 ----------
.../bindings/serial/snps-dw-apb-uart.yaml | 140 ++++++++++++++++++
2 files changed, 140 insertions(+), 76 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
create mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
deleted file mode 100644
index 12bbe9f22560..000000000000
--- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
+++ /dev/null
@@ -1,76 +0,0 @@
-* Synopsys DesignWare ABP UART
-
-Required properties:
-- compatible : "snps,dw-apb-uart"
-- reg : offset and length of the register set for the device.
-- interrupts : should contain uart interrupt.
-
-Clock handling:
-The clock rate of the input clock needs to be supplied by one of
-- clock-frequency : the input clock frequency for the UART.
-- clocks : phandle to the input clock
-
-The supplying peripheral clock can also be handled, needing a second property
-- clock-names: tuple listing input clock names.
- Required elements: "baudclk", "apb_pclk"
-
-Optional properties:
-- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE
- configuration parameter. Define this if your UART does not implement the busy
- functionality.
-- resets : phandle to the parent reset controller.
-- reg-shift : quantity to shift the register offsets by. If this property is
- not present then the register offsets are not shifted.
-- reg-io-width : the size (in bytes) of the IO accesses that should be
- performed on the device. If this property is not present then single byte
- accesses are used.
-- dcd-override : Override the DCD modem status signal. This signal will always
- be reported as active instead of being obtained from the modem status
- register. Define this if your serial port does not use this pin.
-- dsr-override : Override the DTS modem status signal. This signal will always
- be reported as active instead of being obtained from the modem status
- register. Define this if your serial port does not use this pin.
-- cts-override : Override the CTS modem status signal. This signal will always
- be reported as active instead of being obtained from the modem status
- register. Define this if your serial port does not use this pin.
-- ri-override : Override the RI modem status signal. This signal will always be
- reported as inactive instead of being obtained from the modem status register.
- Define this if your serial port does not use this pin.
-
-Example:
-
- uart@80230000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x80230000 0x100>;
- clock-frequency = <3686400>;
- interrupts = <10>;
- reg-shift = <2>;
- reg-io-width = <4>;
- dcd-override;
- dsr-override;
- cts-override;
- ri-override;
- };
-
-Example with one clock:
-
- uart@80230000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x80230000 0x100>;
- clocks = <&baudclk>;
- interrupts = <10>;
- reg-shift = <2>;
- reg-io-width = <4>;
- };
-
-Example with two clocks:
-
- uart@80230000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x80230000 0x100>;
- clocks = <&baudclk>, <&apb_pclk>;
- clock-names = "baudclk", "apb_pclk";
- interrupts = <10>;
- reg-shift = <2>;
- reg-io-width = <4>;
- };
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
new file mode 100644
index 000000000000..b42002542690
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
@@ -0,0 +1,140 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare ABP UART
+
+maintainers:
+ - Rob Herring <robh@kernel.org>
+
+allOf:
+ - $ref: /schemas/serial.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - renesas,r9a06g032-uart
+ - renesas,r9a06g033-uart
+ - const: renesas,rzn1-uart
+ - items:
+ - enum:
+ - rockchip,px30-uart
+ - rockchip,rk3036-uart
+ - rockchip,rk3066-uart
+ - rockchip,rk3188-uart
+ - rockchip,rk3288-uart
+ - rockchip,rk3328-uart
+ - rockchip,rk3368-uart
+ - rockchip,rk3399-uart
+ - rockchip,rv1108-uart
+ - const: snps,dw-apb-uart
+ - items:
+ - enum:
+ - brcm,bcm11351-dw-apb-uart
+ - brcm,bcm21664-dw-apb-uart
+ - const: snps,dw-apb-uart
+ - const: snps,dw-apb-uart
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clock-frequency: true
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: baudclk
+ - const: apb_pclk
+
+ snps,uart-16550-compatible:
+ description: reflects the value of UART_16550_COMPATIBLE configuration
+ parameter. Define this if your UART does not implement the busy functionality.
+ type: boolean
+
+ resets:
+ maxItems: 1
+
+ reg-shift: true
+
+ reg-io-width: true
+
+ dcd-override:
+ description: Override the DCD modem status signal. This signal will
+ always be reported as active instead of being obtained from the modem
+ status register. Define this if your serial port does not use this
+ pin.
+ type: boolean
+
+ dsr-override:
+ description: Override the DTS modem status signal. This signal will
+ always be reported as active instead of being obtained from the modem
+ status register. Define this if your serial port does not use this
+ pin.
+ type: boolean
+
+ cts-override:
+ description: Override the CTS modem status signal. This signal will
+ always be reported as active instead of being obtained from the modem
+ status register. Define this if your serial port does not use this
+ pin.
+ type: boolean
+
+ ri-override:
+ description: Override the RI modem status signal. This signal will always
+ be reported as inactive instead of being obtained from the modem status
+ register. Define this if your serial port does not use this pin.
+ type: boolean
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+examples:
+ - |
+ serial@80230000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x80230000 0x100>;
+ clock-frequency = <3686400>;
+ interrupts = <10>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ dcd-override;
+ dsr-override;
+ cts-override;
+ ri-override;
+ };
+
+ - |
+ // Example with one clock:
+ serial@80230000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x80230000 0x100>;
+ clocks = <&baudclk>;
+ interrupts = <10>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ - |
+ // Example with two clocks:
+ serial@80230000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x80230000 0x100>;
+ clocks = <&baudclk>, <&apb_pclk>;
+ clock-names = "baudclk", "apb_pclk";
+ interrupts = <10>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+...
--
2.19.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] dt-bindings: serial: Move renesas,rzn1-uart into the snps-dw-apb-uart binding
2019-01-10 22:20 [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Rob Herring
@ 2019-01-10 22:20 ` Rob Herring
2019-01-14 9:30 ` Simon Horman
2019-01-14 9:30 ` [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Simon Horman
1 sibling, 1 reply; 6+ messages in thread
From: Rob Herring @ 2019-01-10 22:20 UTC (permalink / raw)
To: devicetree
Cc: linux-kernel, Phil Edworthy, Simon Horman, Greg Kroah-Hartman,
linux-serial
The renesas,rzn1-uart binding only differs in compatible string from the
snps-dw-apb-uart binding. Move it there, converting it to json-schema in
the process.
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/serial/renesas,rzn1-uart.txt | 10 ----------
1 file changed, 10 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
diff --git a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt b/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
deleted file mode 100644
index 8b9e0d4dc2e4..000000000000
--- a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
+++ /dev/null
@@ -1,10 +0,0 @@
-Renesas RZ/N1 UART
-
-This controller is based on the Synopsys DesignWare ABP UART and inherits all
-properties defined in snps-dw-apb-uart.txt except for the compatible property.
-
-Required properties:
-- compatible : The device specific string followed by the generic RZ/N1 string.
- Therefore it must be one of:
- "renesas,r9a06g032-uart", "renesas,rzn1-uart"
- "renesas,r9a06g033-uart", "renesas,rzn1-uart"
--
2.19.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema
2019-01-10 22:20 [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Rob Herring
2019-01-10 22:20 ` [PATCH 2/2] dt-bindings: serial: Move renesas,rzn1-uart into the snps-dw-apb-uart binding Rob Herring
@ 2019-01-14 9:30 ` Simon Horman
2019-01-14 16:23 ` Rob Herring
1 sibling, 1 reply; 6+ messages in thread
From: Simon Horman @ 2019-01-14 9:30 UTC (permalink / raw)
To: Rob Herring; +Cc: devicetree, linux-kernel, Greg Kroah-Hartman, linux-serial
On Thu, Jan 10, 2019 at 04:20:16PM -0600, Rob Herring wrote:
> Convert the snps,dw-apb-uart binding to DT schema using json-schema.
>
> The Rockchip and Broadcom compatible strings were not documented,
> so add them here.
I believe the documentation of the Renesas compatible strings is also new
in this file. Perhaps it would be worth mentioning that too.
In any case
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: linux-serial@vger.kernel.org
> Signed-off-by: Rob Herring <robh@kernel.org>
> ---
> .../bindings/serial/snps-dw-apb-uart.txt | 76 ----------
> .../bindings/serial/snps-dw-apb-uart.yaml | 140 ++++++++++++++++++
> 2 files changed, 140 insertions(+), 76 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
> create mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
>
> diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
> deleted file mode 100644
> index 12bbe9f22560..000000000000
> --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
> +++ /dev/null
> @@ -1,76 +0,0 @@
> -* Synopsys DesignWare ABP UART
> -
> -Required properties:
> -- compatible : "snps,dw-apb-uart"
> -- reg : offset and length of the register set for the device.
> -- interrupts : should contain uart interrupt.
> -
> -Clock handling:
> -The clock rate of the input clock needs to be supplied by one of
> -- clock-frequency : the input clock frequency for the UART.
> -- clocks : phandle to the input clock
> -
> -The supplying peripheral clock can also be handled, needing a second property
> -- clock-names: tuple listing input clock names.
> - Required elements: "baudclk", "apb_pclk"
> -
> -Optional properties:
> -- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE
> - configuration parameter. Define this if your UART does not implement the busy
> - functionality.
> -- resets : phandle to the parent reset controller.
> -- reg-shift : quantity to shift the register offsets by. If this property is
> - not present then the register offsets are not shifted.
> -- reg-io-width : the size (in bytes) of the IO accesses that should be
> - performed on the device. If this property is not present then single byte
> - accesses are used.
> -- dcd-override : Override the DCD modem status signal. This signal will always
> - be reported as active instead of being obtained from the modem status
> - register. Define this if your serial port does not use this pin.
> -- dsr-override : Override the DTS modem status signal. This signal will always
> - be reported as active instead of being obtained from the modem status
> - register. Define this if your serial port does not use this pin.
> -- cts-override : Override the CTS modem status signal. This signal will always
> - be reported as active instead of being obtained from the modem status
> - register. Define this if your serial port does not use this pin.
> -- ri-override : Override the RI modem status signal. This signal will always be
> - reported as inactive instead of being obtained from the modem status register.
> - Define this if your serial port does not use this pin.
> -
> -Example:
> -
> - uart@80230000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x80230000 0x100>;
> - clock-frequency = <3686400>;
> - interrupts = <10>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - dcd-override;
> - dsr-override;
> - cts-override;
> - ri-override;
> - };
> -
> -Example with one clock:
> -
> - uart@80230000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x80230000 0x100>;
> - clocks = <&baudclk>;
> - interrupts = <10>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - };
> -
> -Example with two clocks:
> -
> - uart@80230000 {
> - compatible = "snps,dw-apb-uart";
> - reg = <0x80230000 0x100>;
> - clocks = <&baudclk>, <&apb_pclk>;
> - clock-names = "baudclk", "apb_pclk";
> - interrupts = <10>;
> - reg-shift = <2>;
> - reg-io-width = <4>;
> - };
> diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
> new file mode 100644
> index 000000000000..b42002542690
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
> @@ -0,0 +1,140 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Synopsys DesignWare ABP UART
> +
> +maintainers:
> + - Rob Herring <robh@kernel.org>
> +
> +allOf:
> + - $ref: /schemas/serial.yaml#
> +
> +properties:
> + compatible:
> + oneOf:
> + - items:
> + - enum:
> + - renesas,r9a06g032-uart
> + - renesas,r9a06g033-uart
> + - const: renesas,rzn1-uart
> + - items:
> + - enum:
> + - rockchip,px30-uart
> + - rockchip,rk3036-uart
> + - rockchip,rk3066-uart
> + - rockchip,rk3188-uart
> + - rockchip,rk3288-uart
> + - rockchip,rk3328-uart
> + - rockchip,rk3368-uart
> + - rockchip,rk3399-uart
> + - rockchip,rv1108-uart
> + - const: snps,dw-apb-uart
> + - items:
> + - enum:
> + - brcm,bcm11351-dw-apb-uart
> + - brcm,bcm21664-dw-apb-uart
> + - const: snps,dw-apb-uart
> + - const: snps,dw-apb-uart
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + clock-frequency: true
> +
> + clocks:
> + minItems: 1
> + maxItems: 2
> +
> + clock-names:
> + items:
> + - const: baudclk
> + - const: apb_pclk
> +
> + snps,uart-16550-compatible:
> + description: reflects the value of UART_16550_COMPATIBLE configuration
> + parameter. Define this if your UART does not implement the busy functionality.
> + type: boolean
> +
> + resets:
> + maxItems: 1
> +
> + reg-shift: true
> +
> + reg-io-width: true
> +
> + dcd-override:
> + description: Override the DCD modem status signal. This signal will
> + always be reported as active instead of being obtained from the modem
> + status register. Define this if your serial port does not use this
> + pin.
> + type: boolean
> +
> + dsr-override:
> + description: Override the DTS modem status signal. This signal will
> + always be reported as active instead of being obtained from the modem
> + status register. Define this if your serial port does not use this
> + pin.
> + type: boolean
> +
> + cts-override:
> + description: Override the CTS modem status signal. This signal will
> + always be reported as active instead of being obtained from the modem
> + status register. Define this if your serial port does not use this
> + pin.
> + type: boolean
> +
> + ri-override:
> + description: Override the RI modem status signal. This signal will always
> + be reported as inactive instead of being obtained from the modem status
> + register. Define this if your serial port does not use this pin.
> + type: boolean
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +examples:
> + - |
> + serial@80230000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x80230000 0x100>;
> + clock-frequency = <3686400>;
> + interrupts = <10>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + dcd-override;
> + dsr-override;
> + cts-override;
> + ri-override;
> + };
> +
> + - |
> + // Example with one clock:
> + serial@80230000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x80230000 0x100>;
> + clocks = <&baudclk>;
> + interrupts = <10>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + };
> +
> + - |
> + // Example with two clocks:
> + serial@80230000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x80230000 0x100>;
> + clocks = <&baudclk>, <&apb_pclk>;
> + clock-names = "baudclk", "apb_pclk";
> + interrupts = <10>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + };
> +...
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] dt-bindings: serial: Move renesas,rzn1-uart into the snps-dw-apb-uart binding
2019-01-10 22:20 ` [PATCH 2/2] dt-bindings: serial: Move renesas,rzn1-uart into the snps-dw-apb-uart binding Rob Herring
@ 2019-01-14 9:30 ` Simon Horman
0 siblings, 0 replies; 6+ messages in thread
From: Simon Horman @ 2019-01-14 9:30 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, linux-kernel, Phil Edworthy, Greg Kroah-Hartman,
linux-serial
On Thu, Jan 10, 2019 at 04:20:17PM -0600, Rob Herring wrote:
> The renesas,rzn1-uart binding only differs in compatible string from the
> snps-dw-apb-uart binding. Move it there, converting it to json-schema in
> the process.
This confused me slightly as this patch removes renesas,rzn1-uart.txt
but doesn't add the renesas bindings elsewhere. I now see that is done
in patch 1/2, which is fine. But it might be worth rewording the changelog.
That notwithstanding:
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
> Cc: Phil Edworthy <phil.edworthy@renesas.com>
> Cc: Simon Horman <horms+renesas@verge.net.au>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Cc: linux-serial@vger.kernel.org
> Signed-off-by: Rob Herring <robh@kernel.org>
> ---
> .../devicetree/bindings/serial/renesas,rzn1-uart.txt | 10 ----------
> 1 file changed, 10 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
>
> diff --git a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt b/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
> deleted file mode 100644
> index 8b9e0d4dc2e4..000000000000
> --- a/Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
> +++ /dev/null
> @@ -1,10 +0,0 @@
> -Renesas RZ/N1 UART
> -
> -This controller is based on the Synopsys DesignWare ABP UART and inherits all
> -properties defined in snps-dw-apb-uart.txt except for the compatible property.
> -
> -Required properties:
> -- compatible : The device specific string followed by the generic RZ/N1 string.
> - Therefore it must be one of:
> - "renesas,r9a06g032-uart", "renesas,rzn1-uart"
> - "renesas,r9a06g033-uart", "renesas,rzn1-uart"
> --
> 2.19.1
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema
2019-01-14 9:30 ` [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Simon Horman
@ 2019-01-14 16:23 ` Rob Herring
2019-01-15 8:02 ` Simon Horman
0 siblings, 1 reply; 6+ messages in thread
From: Rob Herring @ 2019-01-14 16:23 UTC (permalink / raw)
To: Simon Horman
Cc: devicetree, linux-kernel, Greg Kroah-Hartman, open list:SERIAL DRIVERS
On Mon, Jan 14, 2019 at 3:30 AM Simon Horman <horms@verge.net.au> wrote:
>
> On Thu, Jan 10, 2019 at 04:20:16PM -0600, Rob Herring wrote:
> > Convert the snps,dw-apb-uart binding to DT schema using json-schema.
> >
> > The Rockchip and Broadcom compatible strings were not documented,
> > so add them here.
>
> I believe the documentation of the Renesas compatible strings is also new
> in this file. Perhaps it would be worth mentioning that too.
Ah, that should be in patch 2. Will respin.
> In any case
>
> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema
2019-01-14 16:23 ` Rob Herring
@ 2019-01-15 8:02 ` Simon Horman
0 siblings, 0 replies; 6+ messages in thread
From: Simon Horman @ 2019-01-15 8:02 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree, linux-kernel, Greg Kroah-Hartman, open list:SERIAL DRIVERS
On Mon, Jan 14, 2019 at 10:23:15AM -0600, Rob Herring wrote:
> On Mon, Jan 14, 2019 at 3:30 AM Simon Horman <horms@verge.net.au> wrote:
> >
> > On Thu, Jan 10, 2019 at 04:20:16PM -0600, Rob Herring wrote:
> > > Convert the snps,dw-apb-uart binding to DT schema using json-schema.
> > >
> > > The Rockchip and Broadcom compatible strings were not documented,
> > > so add them here.
> >
> > I believe the documentation of the Renesas compatible strings is also new
> > in this file. Perhaps it would be worth mentioning that too.
>
> Ah, that should be in patch 2. Will respin.
Thanks!
>
> > In any case
> >
> > Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
> >
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2019-01-15 8:02 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-01-10 22:20 [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Rob Herring
2019-01-10 22:20 ` [PATCH 2/2] dt-bindings: serial: Move renesas,rzn1-uart into the snps-dw-apb-uart binding Rob Herring
2019-01-14 9:30 ` Simon Horman
2019-01-14 9:30 ` [PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema Simon Horman
2019-01-14 16:23 ` Rob Herring
2019-01-15 8:02 ` Simon Horman
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).