* [PATCH v4 1/8] i2c: iproc: Extend I2C read up to 255 bytes
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-04 23:15 ` [PATCH v4 2/8] i2c: iproc: Add slave mode support Ray Jui
` (6 subsequent siblings)
7 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui,
Shreesha Rajashekar
From: Shreesha Rajashekar <shreesha@broadcom.com>
Add support to allow I2C master read transfer up to 255 bytes.
Signed-off-by: Shreesha Rajashekar <shreesha@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
drivers/i2c/busses/i2c-bcm-iproc.c | 98 +++++++++++++++++++++++-------
1 file changed, 76 insertions(+), 22 deletions(-)
diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index 4c8c3bc4669c..eb7339a0280e 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -80,6 +80,10 @@
#define I2C_TIMEOUT_MSEC 50000
#define M_TX_RX_FIFO_SIZE 64
+#define M_RX_FIFO_MAX_THLD_VALUE (M_TX_RX_FIFO_SIZE - 1)
+
+#define M_RX_MAX_READ_LEN 255
+#define M_RX_FIFO_THLD_VALUE 50
enum bus_speed_index {
I2C_SPD_100K = 0,
@@ -102,17 +106,41 @@ struct bcm_iproc_i2c_dev {
/* bytes that have been transferred */
unsigned int tx_bytes;
+ /* bytes that have been read */
+ unsigned int rx_bytes;
+ unsigned int thld_bytes;
};
/*
* Can be expanded in the future if more interrupt status bits are utilized
*/
-#define ISR_MASK (BIT(IS_M_START_BUSY_SHIFT) | BIT(IS_M_TX_UNDERRUN_SHIFT))
+#define ISR_MASK (BIT(IS_M_START_BUSY_SHIFT) | BIT(IS_M_TX_UNDERRUN_SHIFT)\
+ | BIT(IS_M_RX_THLD_SHIFT))
+
+static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
+{
+ struct i2c_msg *msg = iproc_i2c->msg;
+
+ /* Read valid data from RX FIFO */
+ while (iproc_i2c->rx_bytes < msg->len) {
+ if (!((readl(iproc_i2c->base +
+ M_FIFO_CTRL_OFFSET) >>
+ M_FIFO_RX_CNT_SHIFT) &
+ M_FIFO_RX_CNT_MASK))
+ break;
+
+ msg->buf[iproc_i2c->rx_bytes] =
+ (readl(iproc_i2c->base + M_RX_OFFSET) >>
+ M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
+ iproc_i2c->rx_bytes++;
+ }
+}
static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
{
struct bcm_iproc_i2c_dev *iproc_i2c = data;
u32 status = readl(iproc_i2c->base + IS_OFFSET);
+ u32 tmp;
status &= ISR_MASK;
@@ -136,8 +164,6 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
/* mark the last byte */
if (idx == msg->len - 1) {
- u32 tmp;
-
val |= BIT(M_TX_WR_STATUS_SHIFT);
/*
@@ -156,6 +182,32 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
iproc_i2c->tx_bytes += tx_bytes;
}
+ if (status & BIT(IS_M_RX_THLD_SHIFT)) {
+ struct i2c_msg *msg = iproc_i2c->msg;
+ u32 bytes_left;
+
+ bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
+ bytes_left = msg->len - iproc_i2c->rx_bytes;
+ if (bytes_left == 0) {
+ /* finished reading all data, disable rx thld event */
+ tmp = readl(iproc_i2c->base + IE_OFFSET);
+ tmp &= ~BIT(IS_M_RX_THLD_SHIFT);
+ writel(tmp, iproc_i2c->base + IE_OFFSET);
+ } else if (bytes_left < iproc_i2c->thld_bytes) {
+ /* set bytes left as threshold */
+ tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
+ tmp |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
+ writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c->thld_bytes = bytes_left;
+ }
+ /*
+ * bytes_left >= iproc_i2c->thld_bytes,
+ * hence no need to change the THRESHOLD SET.
+ * It will remain as iproc_i2c->thld_bytes itself
+ */
+ }
+
if (status & BIT(IS_M_START_BUSY_SHIFT)) {
iproc_i2c->xfer_is_done = 1;
complete(&iproc_i2c->done);
@@ -253,7 +305,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
{
int ret, i;
u8 addr;
- u32 val;
+ u32 val, tmp, val_intr_en;
unsigned int tx_bytes;
unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
@@ -298,7 +350,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
* transaction is done, i.e., the internal start_busy bit, transitions
* from 1 to 0.
*/
- val = BIT(IE_M_START_BUSY_SHIFT);
+ val_intr_en = BIT(IE_M_START_BUSY_SHIFT);
/*
* If TX data size is larger than the TX FIFO, need to enable TX
@@ -307,9 +359,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
*/
if (!(msg->flags & I2C_M_RD) &&
msg->len > iproc_i2c->tx_bytes)
- val |= BIT(IE_M_TX_UNDERRUN_SHIFT);
-
- writel(val, iproc_i2c->base + IE_OFFSET);
+ val_intr_en |= BIT(IE_M_TX_UNDERRUN_SHIFT);
/*
* Now we can activate the transfer. For a read operation, specify the
@@ -317,11 +367,27 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
*/
val = BIT(M_CMD_START_BUSY_SHIFT);
if (msg->flags & I2C_M_RD) {
+ iproc_i2c->rx_bytes = 0;
+ if (msg->len > M_RX_FIFO_MAX_THLD_VALUE)
+ iproc_i2c->thld_bytes = M_RX_FIFO_THLD_VALUE;
+ else
+ iproc_i2c->thld_bytes = msg->len;
+
+ /* set threshold value */
+ tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
+ tmp |= iproc_i2c->thld_bytes << M_FIFO_RX_THLD_SHIFT;
+ writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+
+ /* enable the RX threshold interrupt */
+ val_intr_en |= BIT(IE_M_RX_THLD_SHIFT);
+
val |= (M_CMD_PROTOCOL_BLK_RD << M_CMD_PROTOCOL_SHIFT) |
(msg->len << M_CMD_RD_CNT_SHIFT);
} else {
val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT);
}
+ writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
writel(val, iproc_i2c->base + M_CMD_OFFSET);
time_left = wait_for_completion_timeout(&iproc_i2c->done, time_left);
@@ -353,17 +419,6 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
return ret;
}
- /*
- * For a read operation, we now need to load the data from FIFO
- * into the memory buffer
- */
- if (msg->flags & I2C_M_RD) {
- for (i = 0; i < msg->len; i++) {
- msg->buf[i] = (readl(iproc_i2c->base + M_RX_OFFSET) >>
- M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
- }
- }
-
return 0;
}
@@ -395,9 +450,8 @@ static const struct i2c_algorithm bcm_iproc_algo = {
.functionality = bcm_iproc_i2c_functionality,
};
-static const struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
- /* need to reserve one byte in the FIFO for the slave address */
- .max_read_len = M_TX_RX_FIFO_SIZE - 1,
+static struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
+ .max_read_len = M_RX_MAX_READ_LEN,
};
static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c)
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v4 2/8] i2c: iproc: Add slave mode support
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
2019-02-04 23:15 ` [PATCH v4 1/8] i2c: iproc: Extend I2C read up to 255 bytes Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-04 23:15 ` [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional Ray Jui
` (5 subsequent siblings)
7 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui,
Shreesha Rajashekar, Michael Cheng
From: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Add slave mode support to the iProc I2C driver.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Michael Cheng <ccheng@broadcom.com>
Signed-off-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
drivers/i2c/busses/Kconfig | 1 +
drivers/i2c/busses/i2c-bcm-iproc.c | 314 ++++++++++++++++++++++++++++-
2 files changed, 309 insertions(+), 6 deletions(-)
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index f2c681971201..e0798b82b3bc 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -424,6 +424,7 @@ config I2C_BCM_IPROC
tristate "Broadcom iProc I2C controller"
depends on ARCH_BCM_IPROC || COMPILE_TEST
default ARCH_BCM_IPROC
+ select I2C_SLAVE
help
If you say yes to this option, support will be included for the
Broadcom iProc I2C controller.
diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index eb7339a0280e..775b3d89a9c4 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -23,11 +23,30 @@
#define CFG_OFFSET 0x00
#define CFG_RESET_SHIFT 31
#define CFG_EN_SHIFT 30
+#define CFG_SLAVE_ADDR_0_SHIFT 28
#define CFG_M_RETRY_CNT_SHIFT 16
#define CFG_M_RETRY_CNT_MASK 0x0f
#define TIM_CFG_OFFSET 0x04
#define TIM_CFG_MODE_400_SHIFT 31
+#define TIM_RAND_SLAVE_STRETCH_SHIFT 24
+#define TIM_RAND_SLAVE_STRETCH_MASK 0x7f
+#define TIM_PERIODIC_SLAVE_STRETCH_SHIFT 16
+#define TIM_PERIODIC_SLAVE_STRETCH_MASK 0x7f
+
+#define S_CFG_SMBUS_ADDR_OFFSET 0x08
+#define S_CFG_EN_NIC_SMB_ADDR3_SHIFT 31
+#define S_CFG_NIC_SMB_ADDR3_SHIFT 24
+#define S_CFG_NIC_SMB_ADDR3_MASK 0x7f
+#define S_CFG_EN_NIC_SMB_ADDR2_SHIFT 23
+#define S_CFG_NIC_SMB_ADDR2_SHIFT 16
+#define S_CFG_NIC_SMB_ADDR2_MASK 0x7f
+#define S_CFG_EN_NIC_SMB_ADDR1_SHIFT 15
+#define S_CFG_NIC_SMB_ADDR1_SHIFT 8
+#define S_CFG_NIC_SMB_ADDR1_MASK 0x7f
+#define S_CFG_EN_NIC_SMB_ADDR0_SHIFT 7
+#define S_CFG_NIC_SMB_ADDR0_SHIFT 0
+#define S_CFG_NIC_SMB_ADDR0_MASK 0x7f
#define M_FIFO_CTRL_OFFSET 0x0c
#define M_FIFO_RX_FLUSH_SHIFT 31
@@ -37,6 +56,14 @@
#define M_FIFO_RX_THLD_SHIFT 8
#define M_FIFO_RX_THLD_MASK 0x3f
+#define S_FIFO_CTRL_OFFSET 0x10
+#define S_FIFO_RX_FLUSH_SHIFT 31
+#define S_FIFO_TX_FLUSH_SHIFT 30
+#define S_FIFO_RX_CNT_SHIFT 16
+#define S_FIFO_RX_CNT_MASK 0x7f
+#define S_FIFO_RX_THLD_SHIFT 8
+#define S_FIFO_RX_THLD_MASK 0x3f
+
#define M_CMD_OFFSET 0x30
#define M_CMD_START_BUSY_SHIFT 31
#define M_CMD_STATUS_SHIFT 25
@@ -46,6 +73,8 @@
#define M_CMD_STATUS_NACK_ADDR 0x2
#define M_CMD_STATUS_NACK_DATA 0x3
#define M_CMD_STATUS_TIMEOUT 0x4
+#define M_CMD_STATUS_FIFO_UNDERRUN 0x5
+#define M_CMD_STATUS_RX_FIFO_FULL 0x6
#define M_CMD_PROTOCOL_SHIFT 9
#define M_CMD_PROTOCOL_MASK 0xf
#define M_CMD_PROTOCOL_BLK_WR 0x7
@@ -54,17 +83,36 @@
#define M_CMD_RD_CNT_SHIFT 0
#define M_CMD_RD_CNT_MASK 0xff
+#define S_CMD_OFFSET 0x34
+#define S_CMD_START_BUSY_SHIFT 31
+#define S_CMD_STATUS_SHIFT 23
+#define S_CMD_STATUS_MASK 0x07
+#define S_CMD_STATUS_SUCCESS 0x0
+#define S_CMD_STATUS_TIMEOUT 0x5
+
#define IE_OFFSET 0x38
#define IE_M_RX_FIFO_FULL_SHIFT 31
#define IE_M_RX_THLD_SHIFT 30
#define IE_M_START_BUSY_SHIFT 28
#define IE_M_TX_UNDERRUN_SHIFT 27
+#define IE_S_RX_FIFO_FULL_SHIFT 26
+#define IE_S_RX_THLD_SHIFT 25
+#define IE_S_RX_EVENT_SHIFT 24
+#define IE_S_START_BUSY_SHIFT 23
+#define IE_S_TX_UNDERRUN_SHIFT 22
+#define IE_S_RD_EVENT_SHIFT 21
#define IS_OFFSET 0x3c
#define IS_M_RX_FIFO_FULL_SHIFT 31
#define IS_M_RX_THLD_SHIFT 30
#define IS_M_START_BUSY_SHIFT 28
#define IS_M_TX_UNDERRUN_SHIFT 27
+#define IS_S_RX_FIFO_FULL_SHIFT 26
+#define IS_S_RX_THLD_SHIFT 25
+#define IS_S_RX_EVENT_SHIFT 24
+#define IS_S_START_BUSY_SHIFT 23
+#define IS_S_TX_UNDERRUN_SHIFT 22
+#define IS_S_RD_EVENT_SHIFT 21
#define M_TX_OFFSET 0x40
#define M_TX_WR_STATUS_SHIFT 31
@@ -78,6 +126,18 @@
#define M_RX_DATA_SHIFT 0
#define M_RX_DATA_MASK 0xff
+#define S_TX_OFFSET 0x48
+#define S_TX_WR_STATUS_SHIFT 31
+#define S_TX_DATA_SHIFT 0
+#define S_TX_DATA_MASK 0xff
+
+#define S_RX_OFFSET 0x4c
+#define S_RX_STATUS_SHIFT 30
+#define S_RX_STATUS_MASK 0x03
+#define S_RX_PEC_ERR_SHIFT 29
+#define S_RX_DATA_SHIFT 0
+#define S_RX_DATA_MASK 0xff
+
#define I2C_TIMEOUT_MSEC 50000
#define M_TX_RX_FIFO_SIZE 64
#define M_RX_FIFO_MAX_THLD_VALUE (M_TX_RX_FIFO_SIZE - 1)
@@ -85,6 +145,30 @@
#define M_RX_MAX_READ_LEN 255
#define M_RX_FIFO_THLD_VALUE 50
+#define IE_M_ALL_INTERRUPT_SHIFT 27
+#define IE_M_ALL_INTERRUPT_MASK 0x1e
+
+#define SLAVE_READ_WRITE_BIT_MASK 0x1
+#define SLAVE_READ_WRITE_BIT_SHIFT 0x1
+#define SLAVE_MAX_SIZE_TRANSACTION 64
+#define SLAVE_CLOCK_STRETCH_TIME 25
+
+#define IE_S_ALL_INTERRUPT_SHIFT 21
+#define IE_S_ALL_INTERRUPT_MASK 0x3f
+
+enum i2c_slave_read_status {
+ I2C_SLAVE_RX_FIFO_EMPTY = 0,
+ I2C_SLAVE_RX_START,
+ I2C_SLAVE_RX_DATA,
+ I2C_SLAVE_RX_END,
+};
+
+enum i2c_slave_xfer_dir {
+ I2C_SLAVE_DIR_READ = 0,
+ I2C_SLAVE_DIR_WRITE,
+ I2C_SLAVE_DIR_NONE,
+};
+
enum bus_speed_index {
I2C_SPD_100K = 0,
I2C_SPD_400K,
@@ -104,6 +188,9 @@ struct bcm_iproc_i2c_dev {
struct i2c_msg *msg;
+ struct i2c_client *slave;
+ enum i2c_slave_xfer_dir xfer_dir;
+
/* bytes that have been transferred */
unsigned int tx_bytes;
/* bytes that have been read */
@@ -117,6 +204,156 @@ struct bcm_iproc_i2c_dev {
#define ISR_MASK (BIT(IS_M_START_BUSY_SHIFT) | BIT(IS_M_TX_UNDERRUN_SHIFT)\
| BIT(IS_M_RX_THLD_SHIFT))
+#define ISR_MASK_SLAVE (BIT(IS_S_START_BUSY_SHIFT)\
+ | BIT(IS_S_RX_EVENT_SHIFT) | BIT(IS_S_RD_EVENT_SHIFT))
+
+static int bcm_iproc_i2c_reg_slave(struct i2c_client *slave);
+static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave);
+static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
+ bool enable);
+
+static void bcm_iproc_i2c_slave_init(
+ struct bcm_iproc_i2c_dev *iproc_i2c, bool need_reset)
+{
+ u32 val;
+
+ if (need_reset) {
+ /* put controller in reset */
+ val = readl(iproc_i2c->base + CFG_OFFSET);
+ val |= BIT(CFG_RESET_SHIFT);
+ writel(val, iproc_i2c->base + CFG_OFFSET);
+
+ /* wait 100 usec per spec */
+ udelay(100);
+
+ /* bring controller out of reset */
+ val &= ~(BIT(CFG_RESET_SHIFT));
+ writel(val, iproc_i2c->base + CFG_OFFSET);
+ }
+
+ /* flush TX/RX FIFOs */
+ val = (BIT(S_FIFO_RX_FLUSH_SHIFT) | BIT(S_FIFO_TX_FLUSH_SHIFT));
+ writel(val, iproc_i2c->base + S_FIFO_CTRL_OFFSET);
+
+ /* RANDOM SLAVE STRETCH time - 20ms*/
+ val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+ val &= ~(TIM_RAND_SLAVE_STRETCH_MASK << TIM_RAND_SLAVE_STRETCH_SHIFT);
+ val |= (SLAVE_CLOCK_STRETCH_TIME << TIM_RAND_SLAVE_STRETCH_SHIFT);
+ writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+
+ /* Configure the slave address */
+ val = readl(iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+ val |= BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
+ val &= ~(S_CFG_NIC_SMB_ADDR3_MASK << S_CFG_NIC_SMB_ADDR3_SHIFT);
+ val |= (iproc_i2c->slave->addr << S_CFG_NIC_SMB_ADDR3_SHIFT);
+ writel(val, iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+
+ /* clear all pending slave interrupts */
+ writel(ISR_MASK_SLAVE, iproc_i2c->base + IS_OFFSET);
+
+ /* Enable interrupt register for any READ event */
+ val = BIT(IE_S_RD_EVENT_SHIFT);
+ /* Enable interrupt register to indicate a valid byte in receive fifo */
+ val |= BIT(IE_S_RX_EVENT_SHIFT);
+ /* Enable interrupt register for the Slave BUSY command */
+ val |= BIT(IE_S_START_BUSY_SHIFT);
+ writel(val, iproc_i2c->base + IE_OFFSET);
+
+ iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
+}
+
+static void bcm_iproc_i2c_check_slave_status(
+ struct bcm_iproc_i2c_dev *iproc_i2c)
+{
+ u32 val;
+
+ val = readl(iproc_i2c->base + S_CMD_OFFSET);
+ val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
+
+ if (val == S_CMD_STATUS_TIMEOUT) {
+ dev_err(iproc_i2c->device, "slave random stretch time timeout\n");
+
+ /* re-initialize i2c for recovery */
+ bcm_iproc_i2c_enable_disable(iproc_i2c, false);
+ bcm_iproc_i2c_slave_init(iproc_i2c, true);
+ bcm_iproc_i2c_enable_disable(iproc_i2c, true);
+ }
+}
+
+static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
+ u32 status)
+{
+ u8 value;
+ u32 val;
+ u32 rd_status;
+ u32 tmp;
+
+ /* Start of transaction. check address and populate the direction */
+ if (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_NONE) {
+ tmp = readl(iproc_i2c->base + S_RX_OFFSET);
+ rd_status = (tmp >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
+ /* This condition checks whether the request is a new request */
+ if (((rd_status == I2C_SLAVE_RX_START) &&
+ (status & BIT(IS_S_RX_EVENT_SHIFT))) ||
+ ((rd_status == I2C_SLAVE_RX_END) &&
+ (status & BIT(IS_S_RD_EVENT_SHIFT)))) {
+
+ /* Last bit is W/R bit.
+ * If 1 then its a read request(by master).
+ */
+ iproc_i2c->xfer_dir = tmp & SLAVE_READ_WRITE_BIT_MASK;
+ if (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_WRITE)
+ i2c_slave_event(iproc_i2c->slave,
+ I2C_SLAVE_READ_REQUESTED, &value);
+ else
+ i2c_slave_event(iproc_i2c->slave,
+ I2C_SLAVE_WRITE_REQUESTED, &value);
+ }
+ }
+
+ /* read request from master */
+ if ((status & BIT(IS_S_RD_EVENT_SHIFT)) &&
+ (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_WRITE)) {
+ i2c_slave_event(iproc_i2c->slave,
+ I2C_SLAVE_READ_PROCESSED, &value);
+ writel(value, iproc_i2c->base + S_TX_OFFSET);
+
+ val = BIT(S_CMD_START_BUSY_SHIFT);
+ writel(val, iproc_i2c->base + S_CMD_OFFSET);
+ }
+
+ /* write request from master */
+ if ((status & BIT(IS_S_RX_EVENT_SHIFT)) &&
+ (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_READ)) {
+ val = readl(iproc_i2c->base + S_RX_OFFSET);
+ /* Its a write request by Master to Slave.
+ * We read data present in receive FIFO
+ */
+ value = (u8)((val >> S_RX_DATA_SHIFT) & S_RX_DATA_MASK);
+ i2c_slave_event(iproc_i2c->slave,
+ I2C_SLAVE_WRITE_RECEIVED, &value);
+
+ /* check the status for the last byte of the transaction */
+ rd_status = (val >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
+ if (rd_status == I2C_SLAVE_RX_END)
+ iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
+
+ dev_dbg(iproc_i2c->device, "\nread value = 0x%x\n", value);
+ }
+
+ /* Stop */
+ if (status & BIT(IS_S_START_BUSY_SHIFT)) {
+ i2c_slave_event(iproc_i2c->slave, I2C_SLAVE_STOP, &value);
+ iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
+ }
+
+ /* clear interrupt status */
+ writel(status, iproc_i2c->base + IS_OFFSET);
+
+ bcm_iproc_i2c_check_slave_status(iproc_i2c);
+ return true;
+}
+
static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
{
struct i2c_msg *msg = iproc_i2c->msg;
@@ -142,6 +379,18 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
u32 status = readl(iproc_i2c->base + IS_OFFSET);
u32 tmp;
+
+ bool ret;
+ u32 sl_status = status & ISR_MASK_SLAVE;
+
+ if (sl_status) {
+ ret = bcm_iproc_i2c_slave_isr(iproc_i2c, sl_status);
+ if (ret)
+ return IRQ_HANDLED;
+ else
+ return IRQ_NONE;
+ }
+
status &= ISR_MASK;
if (!status)
@@ -224,22 +473,25 @@ static int bcm_iproc_i2c_init(struct bcm_iproc_i2c_dev *iproc_i2c)
/* put controller in reset */
val = readl(iproc_i2c->base + CFG_OFFSET);
- val |= 1 << CFG_RESET_SHIFT;
- val &= ~(1 << CFG_EN_SHIFT);
+ val |= BIT(CFG_RESET_SHIFT);
+ val &= ~(BIT(CFG_EN_SHIFT));
writel(val, iproc_i2c->base + CFG_OFFSET);
/* wait 100 usec per spec */
udelay(100);
/* bring controller out of reset */
- val &= ~(1 << CFG_RESET_SHIFT);
+ val &= ~(BIT(CFG_RESET_SHIFT));
writel(val, iproc_i2c->base + CFG_OFFSET);
/* flush TX/RX FIFOs and set RX FIFO threshold to zero */
- val = (1 << M_FIFO_RX_FLUSH_SHIFT) | (1 << M_FIFO_TX_FLUSH_SHIFT);
+ val = (BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT));
writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
/* disable all interrupts */
- writel(0, iproc_i2c->base + IE_OFFSET);
+ val = readl(iproc_i2c->base + IE_OFFSET);
+ val &= ~(IE_M_ALL_INTERRUPT_MASK <<
+ IE_M_ALL_INTERRUPT_SHIFT);
+ writel(val, iproc_i2c->base + IE_OFFSET);
/* clear all pending interrupts */
writel(0xffffffff, iproc_i2c->base + IS_OFFSET);
@@ -288,6 +540,14 @@ static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
dev_dbg(iproc_i2c->device, "bus timeout\n");
return -ETIMEDOUT;
+ case M_CMD_STATUS_FIFO_UNDERRUN:
+ dev_dbg(iproc_i2c->device, "FIFO under-run\n");
+ return -ENXIO;
+
+ case M_CMD_STATUS_RX_FIFO_FULL:
+ dev_dbg(iproc_i2c->device, "Master Rx FIFO full > 10ms\n");
+ return -ETIMEDOUT;
+
default:
dev_dbg(iproc_i2c->device, "unknown error code=%d\n", val);
@@ -442,12 +702,14 @@ static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
static uint32_t bcm_iproc_i2c_functionality(struct i2c_adapter *adap)
{
- return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SLAVE;
}
static const struct i2c_algorithm bcm_iproc_algo = {
.master_xfer = bcm_iproc_i2c_xfer,
.functionality = bcm_iproc_i2c_functionality,
+ .reg_slave = bcm_iproc_i2c_reg_slave,
+ .unreg_slave = bcm_iproc_i2c_unreg_slave,
};
static struct i2c_adapter_quirks bcm_iproc_i2c_quirks = {
@@ -612,6 +874,46 @@ static const struct dev_pm_ops bcm_iproc_i2c_pm_ops = {
#define BCM_IPROC_I2C_PM_OPS NULL
#endif /* CONFIG_PM_SLEEP */
+
+static int bcm_iproc_i2c_reg_slave(struct i2c_client *slave)
+{
+ struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(slave->adapter);
+
+ if (iproc_i2c->slave)
+ return -EBUSY;
+
+ if (slave->flags & I2C_CLIENT_TEN)
+ return -EAFNOSUPPORT;
+
+ iproc_i2c->slave = slave;
+ bcm_iproc_i2c_slave_init(iproc_i2c, false);
+ return 0;
+}
+
+static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)
+{
+ u32 tmp;
+ struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(slave->adapter);
+
+ if (!iproc_i2c->slave)
+ return -EINVAL;
+
+ iproc_i2c->slave = NULL;
+
+ /* disable all slave interrupts */
+ tmp = readl(iproc_i2c->base + IE_OFFSET);
+ tmp &= ~(IE_S_ALL_INTERRUPT_MASK <<
+ IE_S_ALL_INTERRUPT_SHIFT);
+ writel(tmp, iproc_i2c->base + IE_OFFSET);
+
+ /* Erase the slave address programmed */
+ tmp = readl(iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+ tmp &= ~BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
+ writel(tmp, iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+
+ return 0;
+}
+
static const struct of_device_id bcm_iproc_i2c_of_match[] = {
{ .compatible = "brcm,iproc-i2c" },
{ /* sentinel */ }
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
2019-02-04 23:15 ` [PATCH v4 1/8] i2c: iproc: Extend I2C read up to 255 bytes Ray Jui
2019-02-04 23:15 ` [PATCH v4 2/8] i2c: iproc: Add slave mode support Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-13 21:16 ` Rob Herring
2019-02-04 23:15 ` [PATCH v4 4/8] i2c: iproc: add polling support Ray Jui
` (4 subsequent siblings)
7 siblings, 1 reply; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui
In prep for the introduction of polling mode into the driver, update the
binding document to make the 'interrupts' property optional
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
---
.../devicetree/bindings/i2c/brcm,iproc-i2c.txt | 10 +++++++---
1 file changed, 7 insertions(+), 3 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
index 81f982ccca31..d3a3620b1f06 100644
--- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
@@ -9,9 +9,6 @@ Required properties:
Define the base and range of the I/O address space that contain the iProc
I2C controller registers
-- interrupts:
- Should contain the I2C interrupt
-
- clock-frequency:
This is the I2C bus clock. Need to be either 100000 or 400000
@@ -21,6 +18,13 @@ Required properties:
- #size-cells:
Always 0
+Optional properties:
+
+- interrupts:
+ Should contain the I2C interrupt. If unspecified, driver will fall back to
+ polling mode
+
+
Example:
i2c0: i2c@18008000 {
compatible = "brcm,iproc-i2c";
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional
2019-02-04 23:15 ` [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional Ray Jui
@ 2019-02-13 21:16 ` Rob Herring
2019-02-13 22:06 ` Ray Jui
0 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2019-02-13 21:16 UTC (permalink / raw)
To: Ray Jui
Cc: Wolfram Sang, Mark Rutland, linux-i2c, devicetree,
linux-arm-kernel, linux-kernel, bcm-kernel-feedback-list,
Rayagonda Kokatanur
On Mon, Feb 04, 2019 at 03:15:49PM -0800, Ray Jui wrote:
> In prep for the introduction of polling mode into the driver, update the
> binding document to make the 'interrupts' property optional
>
> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
> ---
> .../devicetree/bindings/i2c/brcm,iproc-i2c.txt | 10 +++++++---
> 1 file changed, 7 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> index 81f982ccca31..d3a3620b1f06 100644
> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> @@ -9,9 +9,6 @@ Required properties:
> Define the base and range of the I/O address space that contain the iProc
> I2C controller registers
>
> -- interrupts:
> - Should contain the I2C interrupt
> -
> - clock-frequency:
> This is the I2C bus clock. Need to be either 100000 or 400000
>
> @@ -21,6 +18,13 @@ Required properties:
> - #size-cells:
> Always 0
>
> +Optional properties:
> +
> +- interrupts:
> + Should contain the I2C interrupt. If unspecified, driver will fall back to
> + polling mode
What determines when you want to use polling mode? I'm not sure DT
is the best way to control this unless it's really a property of
the h/w. Driver behavior is really outside the scope of the DT. u-boot
would use polling even if an interrupt is specified, for example.
Rob
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional
2019-02-13 21:16 ` Rob Herring
@ 2019-02-13 22:06 ` Ray Jui
2019-02-14 14:16 ` Rob Herring
0 siblings, 1 reply; 17+ messages in thread
From: Ray Jui @ 2019-02-13 22:06 UTC (permalink / raw)
To: Rob Herring
Cc: Wolfram Sang, Mark Rutland, linux-i2c, devicetree,
linux-arm-kernel, linux-kernel, bcm-kernel-feedback-list,
Rayagonda Kokatanur
Hi Rob,
On 2/13/2019 1:16 PM, Rob Herring wrote:
> On Mon, Feb 04, 2019 at 03:15:49PM -0800, Ray Jui wrote:
>> In prep for the introduction of polling mode into the driver, update the
>> binding document to make the 'interrupts' property optional
>>
>> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
>> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>> ---
>> .../devicetree/bindings/i2c/brcm,iproc-i2c.txt | 10 +++++++---
>> 1 file changed, 7 insertions(+), 3 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>> index 81f982ccca31..d3a3620b1f06 100644
>> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>> @@ -9,9 +9,6 @@ Required properties:
>> Define the base and range of the I/O address space that contain the iProc
>> I2C controller registers
>>
>> -- interrupts:
>> - Should contain the I2C interrupt
>> -
>> - clock-frequency:
>> This is the I2C bus clock. Need to be either 100000 or 400000
>>
>> @@ -21,6 +18,13 @@ Required properties:
>> - #size-cells:
>> Always 0
>>
>> +Optional properties:
>> +
>> +- interrupts:
>> + Should contain the I2C interrupt. If unspecified, driver will fall back to
>> + polling mode
>
> What determines when you want to use polling mode? I'm not sure DT
> is the best way to control this unless it's really a property of
> the h/w. Driver behavior is really outside the scope of the DT. u-boot
> would use polling even if an interrupt is specified, for example.
>
It's tied to the particular revision of the I2C controller, i.e., the
iProc NIC i2c controller does not have interrupt line wired. In this
case, the behavior is determined by the DT compatible string of the
iProc I2C device. I thought that it makes sense to now move the
'interrupts' property to be under "Optional" than "Required" which is
basically what this change is.
> Rob
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional
2019-02-13 22:06 ` Ray Jui
@ 2019-02-14 14:16 ` Rob Herring
2019-02-14 17:36 ` Ray Jui
0 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2019-02-14 14:16 UTC (permalink / raw)
To: Ray Jui
Cc: Wolfram Sang, Mark Rutland, Linux I2C, devicetree,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
linux-kernel, maintainer:BROADCOM BCM7XXX ARM ARCHITECTURE,
Rayagonda Kokatanur
On Wed, Feb 13, 2019 at 4:06 PM Ray Jui <ray.jui@broadcom.com> wrote:
>
> Hi Rob,
>
> On 2/13/2019 1:16 PM, Rob Herring wrote:
> > On Mon, Feb 04, 2019 at 03:15:49PM -0800, Ray Jui wrote:
> >> In prep for the introduction of polling mode into the driver, update the
> >> binding document to make the 'interrupts' property optional
> >>
> >> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
> >> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
> >> ---
> >> .../devicetree/bindings/i2c/brcm,iproc-i2c.txt | 10 +++++++---
> >> 1 file changed, 7 insertions(+), 3 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> >> index 81f982ccca31..d3a3620b1f06 100644
> >> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> >> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> >> @@ -9,9 +9,6 @@ Required properties:
> >> Define the base and range of the I/O address space that contain the iProc
> >> I2C controller registers
> >>
> >> -- interrupts:
> >> - Should contain the I2C interrupt
> >> -
> >> - clock-frequency:
> >> This is the I2C bus clock. Need to be either 100000 or 400000
> >>
> >> @@ -21,6 +18,13 @@ Required properties:
> >> - #size-cells:
> >> Always 0
> >>
> >> +Optional properties:
> >> +
> >> +- interrupts:
> >> + Should contain the I2C interrupt. If unspecified, driver will fall back to
> >> + polling mode
> >
> > What determines when you want to use polling mode? I'm not sure DT
> > is the best way to control this unless it's really a property of
> > the h/w. Driver behavior is really outside the scope of the DT. u-boot
> > would use polling even if an interrupt is specified, for example.
> >
> It's tied to the particular revision of the I2C controller, i.e., the
> iProc NIC i2c controller does not have interrupt line wired. In this
> case, the behavior is determined by the DT compatible string of the
> iProc I2C device. I thought that it makes sense to now move the
> 'interrupts' property to be under "Optional" than "Required" which is
> basically what this change is.
Okay, please put this detail into the commit msg.
Rob
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional
2019-02-14 14:16 ` Rob Herring
@ 2019-02-14 17:36 ` Ray Jui
0 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-14 17:36 UTC (permalink / raw)
To: Rob Herring
Cc: Wolfram Sang, Mark Rutland, Linux I2C, devicetree,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
linux-kernel, maintainer:BROADCOM BCM7XXX ARM ARCHITECTURE,
Rayagonda Kokatanur
On 2/14/2019 6:16 AM, Rob Herring wrote:
> On Wed, Feb 13, 2019 at 4:06 PM Ray Jui <ray.jui@broadcom.com> wrote:
>>
>> Hi Rob,
>>
>> On 2/13/2019 1:16 PM, Rob Herring wrote:
>>> On Mon, Feb 04, 2019 at 03:15:49PM -0800, Ray Jui wrote:
>>>> In prep for the introduction of polling mode into the driver, update the
>>>> binding document to make the 'interrupts' property optional
>>>>
>>>> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
>>>> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>>>> ---
>>>> .../devicetree/bindings/i2c/brcm,iproc-i2c.txt | 10 +++++++---
>>>> 1 file changed, 7 insertions(+), 3 deletions(-)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>>>> index 81f982ccca31..d3a3620b1f06 100644
>>>> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>>>> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>>>> @@ -9,9 +9,6 @@ Required properties:
>>>> Define the base and range of the I/O address space that contain the iProc
>>>> I2C controller registers
>>>>
>>>> -- interrupts:
>>>> - Should contain the I2C interrupt
>>>> -
>>>> - clock-frequency:
>>>> This is the I2C bus clock. Need to be either 100000 or 400000
>>>>
>>>> @@ -21,6 +18,13 @@ Required properties:
>>>> - #size-cells:
>>>> Always 0
>>>>
>>>> +Optional properties:
>>>> +
>>>> +- interrupts:
>>>> + Should contain the I2C interrupt. If unspecified, driver will fall back to
>>>> + polling mode
>>>
>>> What determines when you want to use polling mode? I'm not sure DT
>>> is the best way to control this unless it's really a property of
>>> the h/w. Driver behavior is really outside the scope of the DT. u-boot
>>> would use polling even if an interrupt is specified, for example.
>>>
>> It's tied to the particular revision of the I2C controller, i.e., the
>> iProc NIC i2c controller does not have interrupt line wired. In this
>> case, the behavior is determined by the DT compatible string of the
>> iProc I2C device. I thought that it makes sense to now move the
>> 'interrupts' property to be under "Optional" than "Required" which is
>> basically what this change is.
>
> Okay, please put this detail into the commit msg.
Will do! Thanks.
>
> Rob
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v4 4/8] i2c: iproc: add polling support
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
` (2 preceding siblings ...)
2019-02-04 23:15 ` [PATCH v4 3/8] dt-bindings: i2c: iproc: make 'interrupts' optional Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-04 23:15 ` [PATCH v4 5/8] i2c: iproc: use wrapper for read/write access Ray Jui
` (3 subsequent siblings)
7 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui
From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Add polling support to the iProc I2C driver. Polling mode is
activated when the driver fails to obtain an interrupt ID from device
tree
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
drivers/i2c/busses/i2c-bcm-iproc.c | 298 ++++++++++++++++++-----------
1 file changed, 181 insertions(+), 117 deletions(-)
diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index 775b3d89a9c4..073e5a8888ad 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -373,95 +373,115 @@ static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
}
}
-static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
+static void bcm_iproc_i2c_send(struct bcm_iproc_i2c_dev *iproc_i2c)
{
- struct bcm_iproc_i2c_dev *iproc_i2c = data;
- u32 status = readl(iproc_i2c->base + IS_OFFSET);
- u32 tmp;
-
-
- bool ret;
- u32 sl_status = status & ISR_MASK_SLAVE;
-
- if (sl_status) {
- ret = bcm_iproc_i2c_slave_isr(iproc_i2c, sl_status);
- if (ret)
- return IRQ_HANDLED;
- else
- return IRQ_NONE;
- }
+ struct i2c_msg *msg = iproc_i2c->msg;
+ unsigned int tx_bytes = msg->len - iproc_i2c->tx_bytes;
+ unsigned int i;
+ u32 val;
- status &= ISR_MASK;
+ /* can only fill up to the FIFO size */
+ tx_bytes = min_t(unsigned int, tx_bytes, M_TX_RX_FIFO_SIZE);
+ for (i = 0; i < tx_bytes; i++) {
+ /* start from where we left over */
+ unsigned int idx = iproc_i2c->tx_bytes + i;
- if (!status)
- return IRQ_NONE;
+ val = msg->buf[idx];
- /* TX FIFO is empty and we have more data to send */
- if (status & BIT(IS_M_TX_UNDERRUN_SHIFT)) {
- struct i2c_msg *msg = iproc_i2c->msg;
- unsigned int tx_bytes = msg->len - iproc_i2c->tx_bytes;
- unsigned int i;
- u32 val;
-
- /* can only fill up to the FIFO size */
- tx_bytes = min_t(unsigned int, tx_bytes, M_TX_RX_FIFO_SIZE);
- for (i = 0; i < tx_bytes; i++) {
- /* start from where we left over */
- unsigned int idx = iproc_i2c->tx_bytes + i;
+ /* mark the last byte */
+ if (idx == msg->len - 1) {
+ val |= BIT(M_TX_WR_STATUS_SHIFT);
- val = msg->buf[idx];
-
- /* mark the last byte */
- if (idx == msg->len - 1) {
- val |= BIT(M_TX_WR_STATUS_SHIFT);
+ if (iproc_i2c->irq) {
+ u32 tmp;
/*
- * Since this is the last byte, we should
- * now disable TX FIFO underrun interrupt
+ * Since this is the last byte, we should now
+ * disable TX FIFO underrun interrupt
*/
tmp = readl(iproc_i2c->base + IE_OFFSET);
tmp &= ~BIT(IE_M_TX_UNDERRUN_SHIFT);
writel(tmp, iproc_i2c->base + IE_OFFSET);
}
-
- /* load data into TX FIFO */
- writel(val, iproc_i2c->base + M_TX_OFFSET);
}
- /* update number of transferred bytes */
- iproc_i2c->tx_bytes += tx_bytes;
+
+ /* load data into TX FIFO */
+ writel(val, iproc_i2c->base + M_TX_OFFSET);
}
- if (status & BIT(IS_M_RX_THLD_SHIFT)) {
- struct i2c_msg *msg = iproc_i2c->msg;
- u32 bytes_left;
+ /* update number of transferred bytes */
+ iproc_i2c->tx_bytes += tx_bytes;
+}
- bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
- bytes_left = msg->len - iproc_i2c->rx_bytes;
- if (bytes_left == 0) {
+static void bcm_iproc_i2c_read(struct bcm_iproc_i2c_dev *iproc_i2c)
+{
+ struct i2c_msg *msg = iproc_i2c->msg;
+ u32 bytes_left, val;
+
+ bcm_iproc_i2c_read_valid_bytes(iproc_i2c);
+ bytes_left = msg->len - iproc_i2c->rx_bytes;
+ if (bytes_left == 0) {
+ if (iproc_i2c->irq) {
/* finished reading all data, disable rx thld event */
- tmp = readl(iproc_i2c->base + IE_OFFSET);
- tmp &= ~BIT(IS_M_RX_THLD_SHIFT);
- writel(tmp, iproc_i2c->base + IE_OFFSET);
- } else if (bytes_left < iproc_i2c->thld_bytes) {
- /* set bytes left as threshold */
- tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
- tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
- tmp |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
- writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
- iproc_i2c->thld_bytes = bytes_left;
+ val = readl(iproc_i2c->base + IE_OFFSET);
+ val &= ~BIT(IS_M_RX_THLD_SHIFT);
+ writel(val, iproc_i2c->base + IE_OFFSET);
}
- /*
- * bytes_left >= iproc_i2c->thld_bytes,
- * hence no need to change the THRESHOLD SET.
- * It will remain as iproc_i2c->thld_bytes itself
- */
+ } else if (bytes_left < iproc_i2c->thld_bytes) {
+ /* set bytes left as threshold */
+ val = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ val &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
+ val |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
+ writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c->thld_bytes = bytes_left;
}
+ /*
+ * bytes_left >= iproc_i2c->thld_bytes,
+ * hence no need to change the THRESHOLD SET.
+ * It will remain as iproc_i2c->thld_bytes itself
+ */
+}
+static void bcm_iproc_i2c_process_m_event(struct bcm_iproc_i2c_dev *iproc_i2c,
+ u32 status)
+{
+ /* TX FIFO is empty and we have more data to send */
+ if (status & BIT(IS_M_TX_UNDERRUN_SHIFT))
+ bcm_iproc_i2c_send(iproc_i2c);
+
+ /* RX FIFO threshold is reached and data needs to be read out */
+ if (status & BIT(IS_M_RX_THLD_SHIFT))
+ bcm_iproc_i2c_read(iproc_i2c);
+
+ /* transfer is done */
if (status & BIT(IS_M_START_BUSY_SHIFT)) {
iproc_i2c->xfer_is_done = 1;
- complete(&iproc_i2c->done);
+ if (iproc_i2c->irq)
+ complete(&iproc_i2c->done);
+ }
+}
+
+static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
+{
+ struct bcm_iproc_i2c_dev *iproc_i2c = data;
+ u32 status = readl(iproc_i2c->base + IS_OFFSET);
+ bool ret;
+ u32 sl_status = status & ISR_MASK_SLAVE;
+
+ if (sl_status) {
+ ret = bcm_iproc_i2c_slave_isr(iproc_i2c, sl_status);
+ if (ret)
+ return IRQ_HANDLED;
+ else
+ return IRQ_NONE;
}
+ status &= ISR_MASK;
+ if (!status)
+ return IRQ_NONE;
+
+ /* process all master based events */
+ bcm_iproc_i2c_process_m_event(iproc_i2c, status);
writel(status, iproc_i2c->base + IS_OFFSET);
return IRQ_HANDLED;
@@ -560,14 +580,71 @@ static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
}
}
+static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
+ struct i2c_msg *msg,
+ u32 cmd)
+{
+ unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
+ u32 val, status;
+ int ret;
+
+ writel(cmd, iproc_i2c->base + M_CMD_OFFSET);
+
+ if (iproc_i2c->irq) {
+ time_left = wait_for_completion_timeout(&iproc_i2c->done,
+ time_left);
+ /* disable all interrupts */
+ writel(0, iproc_i2c->base + IE_OFFSET);
+ /* read it back to flush the write */
+ readl(iproc_i2c->base + IE_OFFSET);
+ /* make sure the interrupt handler isn't running */
+ synchronize_irq(iproc_i2c->irq);
+
+ } else { /* polling mode */
+ unsigned long timeout = jiffies + time_left;
+
+ do {
+ status = readl(iproc_i2c->base + IS_OFFSET) & ISR_MASK;
+ bcm_iproc_i2c_process_m_event(iproc_i2c, status);
+ writel(status, iproc_i2c->base + IS_OFFSET);
+
+ if (time_after(jiffies, timeout)) {
+ time_left = 0;
+ break;
+ }
+
+ cpu_relax();
+ cond_resched();
+ } while (!iproc_i2c->xfer_is_done);
+ }
+
+ if (!time_left && !iproc_i2c->xfer_is_done) {
+ dev_err(iproc_i2c->device, "transaction timed out\n");
+
+ /* flush both TX/RX FIFOs */
+ val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
+ writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ return -ETIMEDOUT;
+ }
+
+ ret = bcm_iproc_i2c_check_status(iproc_i2c, msg);
+ if (ret) {
+ /* flush both TX/RX FIFOs */
+ val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
+ writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ return ret;
+ }
+
+ return 0;
+}
+
static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
struct i2c_msg *msg)
{
- int ret, i;
+ int i;
u8 addr;
u32 val, tmp, val_intr_en;
unsigned int tx_bytes;
- unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MSEC);
/* check if bus is busy */
if (!!(readl(iproc_i2c->base + M_CMD_OFFSET) &
@@ -602,7 +679,9 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
}
/* mark as incomplete before starting the transaction */
- reinit_completion(&iproc_i2c->done);
+ if (iproc_i2c->irq)
+ reinit_completion(&iproc_i2c->done);
+
iproc_i2c->xfer_is_done = 0;
/*
@@ -647,39 +726,11 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
} else {
val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT);
}
- writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
- writel(val, iproc_i2c->base + M_CMD_OFFSET);
- time_left = wait_for_completion_timeout(&iproc_i2c->done, time_left);
+ if (iproc_i2c->irq)
+ writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
- /* disable all interrupts */
- writel(0, iproc_i2c->base + IE_OFFSET);
- /* read it back to flush the write */
- readl(iproc_i2c->base + IE_OFFSET);
-
- /* make sure the interrupt handler isn't running */
- synchronize_irq(iproc_i2c->irq);
-
- if (!time_left && !iproc_i2c->xfer_is_done) {
- dev_err(iproc_i2c->device, "transaction timed out\n");
-
- /* flush FIFOs */
- val = (1 << M_FIFO_RX_FLUSH_SHIFT) |
- (1 << M_FIFO_TX_FLUSH_SHIFT);
- writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
- return -ETIMEDOUT;
- }
-
- ret = bcm_iproc_i2c_check_status(iproc_i2c, msg);
- if (ret) {
- /* flush both TX/RX FIFOs */
- val = (1 << M_FIFO_RX_FLUSH_SHIFT) |
- (1 << M_FIFO_TX_FLUSH_SHIFT);
- writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
- return ret;
- }
-
- return 0;
+ return bcm_iproc_i2c_xfer_wait(iproc_i2c, msg, val);
}
static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
@@ -781,17 +832,20 @@ static int bcm_iproc_i2c_probe(struct platform_device *pdev)
return ret;
irq = platform_get_irq(pdev, 0);
- if (irq <= 0) {
- dev_err(iproc_i2c->device, "no irq resource\n");
- return irq;
- }
- iproc_i2c->irq = irq;
+ if (irq > 0) {
+ ret = devm_request_irq(iproc_i2c->device, irq,
+ bcm_iproc_i2c_isr, 0, pdev->name,
+ iproc_i2c);
+ if (ret < 0) {
+ dev_err(iproc_i2c->device,
+ "unable to request irq %i\n", irq);
+ return ret;
+ }
- ret = devm_request_irq(iproc_i2c->device, irq, bcm_iproc_i2c_isr, 0,
- pdev->name, iproc_i2c);
- if (ret < 0) {
- dev_err(iproc_i2c->device, "unable to request irq %i\n", irq);
- return ret;
+ iproc_i2c->irq = irq;
+ } else {
+ dev_warn(iproc_i2c->device,
+ "no irq resource, falling back to poll mode\n");
}
bcm_iproc_i2c_enable_disable(iproc_i2c, true);
@@ -811,10 +865,15 @@ static int bcm_iproc_i2c_remove(struct platform_device *pdev)
{
struct bcm_iproc_i2c_dev *iproc_i2c = platform_get_drvdata(pdev);
- /* make sure there's no pending interrupt when we remove the adapter */
- writel(0, iproc_i2c->base + IE_OFFSET);
- readl(iproc_i2c->base + IE_OFFSET);
- synchronize_irq(iproc_i2c->irq);
+ if (iproc_i2c->irq) {
+ /*
+ * Make sure there's no pending interrupt when we remove the
+ * adapter
+ */
+ writel(0, iproc_i2c->base + IE_OFFSET);
+ readl(iproc_i2c->base + IE_OFFSET);
+ synchronize_irq(iproc_i2c->irq);
+ }
i2c_del_adapter(&iproc_i2c->adapter);
bcm_iproc_i2c_enable_disable(iproc_i2c, false);
@@ -828,10 +887,15 @@ static int bcm_iproc_i2c_suspend(struct device *dev)
{
struct bcm_iproc_i2c_dev *iproc_i2c = dev_get_drvdata(dev);
- /* make sure there's no pending interrupt when we go into suspend */
- writel(0, iproc_i2c->base + IE_OFFSET);
- readl(iproc_i2c->base + IE_OFFSET);
- synchronize_irq(iproc_i2c->irq);
+ if (iproc_i2c->irq) {
+ /*
+ * Make sure there's no pending interrupt when we go into
+ * suspend
+ */
+ writel(0, iproc_i2c->base + IE_OFFSET);
+ readl(iproc_i2c->base + IE_OFFSET);
+ synchronize_irq(iproc_i2c->irq);
+ }
/* now disable the controller */
bcm_iproc_i2c_enable_disable(iproc_i2c, false);
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v4 5/8] i2c: iproc: use wrapper for read/write access
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
` (3 preceding siblings ...)
2019-02-04 23:15 ` [PATCH v4 4/8] i2c: iproc: add polling support Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-04 23:15 ` [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string Ray Jui
` (2 subsequent siblings)
7 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui
From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Use the following wrapper for read/write access of iProc i2c registers:
u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 offset)
void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c, u32 offset,
u32 val)
This preps the driver for support of indirect register access required
by certain SoCs with this iProc I2C block integrated
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
drivers/i2c/busses/i2c-bcm-iproc.c | 145 ++++++++++++++++-------------
1 file changed, 79 insertions(+), 66 deletions(-)
diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index 073e5a8888ad..5b9cbd7a3776 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -212,6 +212,18 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave);
static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
bool enable);
+static inline u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
+ u32 offset)
+{
+ return readl(iproc_i2c->base + offset);
+}
+
+static inline void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
+ u32 offset, u32 val)
+{
+ writel(val, iproc_i2c->base + offset);
+}
+
static void bcm_iproc_i2c_slave_init(
struct bcm_iproc_i2c_dev *iproc_i2c, bool need_reset)
{
@@ -219,37 +231,37 @@ static void bcm_iproc_i2c_slave_init(
if (need_reset) {
/* put controller in reset */
- val = readl(iproc_i2c->base + CFG_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
val |= BIT(CFG_RESET_SHIFT);
- writel(val, iproc_i2c->base + CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
/* wait 100 usec per spec */
udelay(100);
/* bring controller out of reset */
val &= ~(BIT(CFG_RESET_SHIFT));
- writel(val, iproc_i2c->base + CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
}
/* flush TX/RX FIFOs */
val = (BIT(S_FIFO_RX_FLUSH_SHIFT) | BIT(S_FIFO_TX_FLUSH_SHIFT));
- writel(val, iproc_i2c->base + S_FIFO_CTRL_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, S_FIFO_CTRL_OFFSET, val);
/* RANDOM SLAVE STRETCH time - 20ms*/
- val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
val &= ~(TIM_RAND_SLAVE_STRETCH_MASK << TIM_RAND_SLAVE_STRETCH_SHIFT);
val |= (SLAVE_CLOCK_STRETCH_TIME << TIM_RAND_SLAVE_STRETCH_SHIFT);
- writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
/* Configure the slave address */
- val = readl(iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET);
val |= BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
val &= ~(S_CFG_NIC_SMB_ADDR3_MASK << S_CFG_NIC_SMB_ADDR3_SHIFT);
val |= (iproc_i2c->slave->addr << S_CFG_NIC_SMB_ADDR3_SHIFT);
- writel(val, iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET, val);
/* clear all pending slave interrupts */
- writel(ISR_MASK_SLAVE, iproc_i2c->base + IS_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, ISR_MASK_SLAVE);
/* Enable interrupt register for any READ event */
val = BIT(IE_S_RD_EVENT_SHIFT);
@@ -257,7 +269,7 @@ static void bcm_iproc_i2c_slave_init(
val |= BIT(IE_S_RX_EVENT_SHIFT);
/* Enable interrupt register for the Slave BUSY command */
val |= BIT(IE_S_START_BUSY_SHIFT);
- writel(val, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
iproc_i2c->xfer_dir = I2C_SLAVE_DIR_NONE;
}
@@ -267,7 +279,7 @@ static void bcm_iproc_i2c_check_slave_status(
{
u32 val;
- val = readl(iproc_i2c->base + S_CMD_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, S_CMD_OFFSET);
val = (val >> S_CMD_STATUS_SHIFT) & S_CMD_STATUS_MASK;
if (val == S_CMD_STATUS_TIMEOUT) {
@@ -290,7 +302,7 @@ static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
/* Start of transaction. check address and populate the direction */
if (iproc_i2c->xfer_dir == I2C_SLAVE_DIR_NONE) {
- tmp = readl(iproc_i2c->base + S_RX_OFFSET);
+ tmp = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
rd_status = (tmp >> S_RX_STATUS_SHIFT) & S_RX_STATUS_MASK;
/* This condition checks whether the request is a new request */
if (((rd_status == I2C_SLAVE_RX_START) &&
@@ -316,16 +328,16 @@ static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
(iproc_i2c->xfer_dir == I2C_SLAVE_DIR_WRITE)) {
i2c_slave_event(iproc_i2c->slave,
I2C_SLAVE_READ_PROCESSED, &value);
- writel(value, iproc_i2c->base + S_TX_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, S_TX_OFFSET, value);
val = BIT(S_CMD_START_BUSY_SHIFT);
- writel(val, iproc_i2c->base + S_CMD_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, S_CMD_OFFSET, val);
}
/* write request from master */
if ((status & BIT(IS_S_RX_EVENT_SHIFT)) &&
(iproc_i2c->xfer_dir == I2C_SLAVE_DIR_READ)) {
- val = readl(iproc_i2c->base + S_RX_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, S_RX_OFFSET);
/* Its a write request by Master to Slave.
* We read data present in receive FIFO
*/
@@ -348,7 +360,7 @@ static bool bcm_iproc_i2c_slave_isr(struct bcm_iproc_i2c_dev *iproc_i2c,
}
/* clear interrupt status */
- writel(status, iproc_i2c->base + IS_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
bcm_iproc_i2c_check_slave_status(iproc_i2c);
return true;
@@ -360,14 +372,13 @@ static void bcm_iproc_i2c_read_valid_bytes(struct bcm_iproc_i2c_dev *iproc_i2c)
/* Read valid data from RX FIFO */
while (iproc_i2c->rx_bytes < msg->len) {
- if (!((readl(iproc_i2c->base +
- M_FIFO_CTRL_OFFSET) >>
- M_FIFO_RX_CNT_SHIFT) &
- M_FIFO_RX_CNT_MASK))
+ if (!((iproc_i2c_rd_reg(iproc_i2c,
+ M_FIFO_CTRL_OFFSET) >>
+ M_FIFO_RX_CNT_SHIFT) & M_FIFO_RX_CNT_MASK))
break;
msg->buf[iproc_i2c->rx_bytes] =
- (readl(iproc_i2c->base + M_RX_OFFSET) >>
+ (iproc_i2c_rd_reg(iproc_i2c, M_RX_OFFSET) >>
M_RX_DATA_SHIFT) & M_RX_DATA_MASK;
iproc_i2c->rx_bytes++;
}
@@ -399,14 +410,15 @@ static void bcm_iproc_i2c_send(struct bcm_iproc_i2c_dev *iproc_i2c)
* Since this is the last byte, we should now
* disable TX FIFO underrun interrupt
*/
- tmp = readl(iproc_i2c->base + IE_OFFSET);
+ tmp = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
tmp &= ~BIT(IE_M_TX_UNDERRUN_SHIFT);
- writel(tmp, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET,
+ tmp);
}
}
/* load data into TX FIFO */
- writel(val, iproc_i2c->base + M_TX_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
}
/* update number of transferred bytes */
@@ -423,16 +435,16 @@ static void bcm_iproc_i2c_read(struct bcm_iproc_i2c_dev *iproc_i2c)
if (bytes_left == 0) {
if (iproc_i2c->irq) {
/* finished reading all data, disable rx thld event */
- val = readl(iproc_i2c->base + IE_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
val &= ~BIT(IS_M_RX_THLD_SHIFT);
- writel(val, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
}
} else if (bytes_left < iproc_i2c->thld_bytes) {
/* set bytes left as threshold */
- val = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET);
val &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
val |= (bytes_left << M_FIFO_RX_THLD_SHIFT);
- writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
iproc_i2c->thld_bytes = bytes_left;
}
/*
@@ -464,7 +476,7 @@ static void bcm_iproc_i2c_process_m_event(struct bcm_iproc_i2c_dev *iproc_i2c,
static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
{
struct bcm_iproc_i2c_dev *iproc_i2c = data;
- u32 status = readl(iproc_i2c->base + IS_OFFSET);
+ u32 status = iproc_i2c_rd_reg(iproc_i2c, IS_OFFSET);
bool ret;
u32 sl_status = status & ISR_MASK_SLAVE;
@@ -482,7 +494,7 @@ static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data)
/* process all master based events */
bcm_iproc_i2c_process_m_event(iproc_i2c, status);
- writel(status, iproc_i2c->base + IS_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
return IRQ_HANDLED;
}
@@ -492,29 +504,29 @@ static int bcm_iproc_i2c_init(struct bcm_iproc_i2c_dev *iproc_i2c)
u32 val;
/* put controller in reset */
- val = readl(iproc_i2c->base + CFG_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
val |= BIT(CFG_RESET_SHIFT);
val &= ~(BIT(CFG_EN_SHIFT));
- writel(val, iproc_i2c->base + CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
/* wait 100 usec per spec */
udelay(100);
/* bring controller out of reset */
val &= ~(BIT(CFG_RESET_SHIFT));
- writel(val, iproc_i2c->base + CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
/* flush TX/RX FIFOs and set RX FIFO threshold to zero */
val = (BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT));
- writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
/* disable all interrupts */
- val = readl(iproc_i2c->base + IE_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
val &= ~(IE_M_ALL_INTERRUPT_MASK <<
IE_M_ALL_INTERRUPT_SHIFT);
- writel(val, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val);
/* clear all pending interrupts */
- writel(0xffffffff, iproc_i2c->base + IS_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, 0xffffffff);
return 0;
}
@@ -524,12 +536,12 @@ static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
{
u32 val;
- val = readl(iproc_i2c->base + CFG_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, CFG_OFFSET);
if (enable)
val |= BIT(CFG_EN_SHIFT);
else
val &= ~BIT(CFG_EN_SHIFT);
- writel(val, iproc_i2c->base + CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, CFG_OFFSET, val);
}
static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
@@ -537,7 +549,7 @@ static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c,
{
u32 val;
- val = readl(iproc_i2c->base + M_CMD_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, M_CMD_OFFSET);
val = (val >> M_CMD_STATUS_SHIFT) & M_CMD_STATUS_MASK;
switch (val) {
@@ -588,15 +600,15 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 val, status;
int ret;
- writel(cmd, iproc_i2c->base + M_CMD_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_CMD_OFFSET, cmd);
if (iproc_i2c->irq) {
time_left = wait_for_completion_timeout(&iproc_i2c->done,
time_left);
/* disable all interrupts */
- writel(0, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
/* read it back to flush the write */
- readl(iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
/* make sure the interrupt handler isn't running */
synchronize_irq(iproc_i2c->irq);
@@ -604,9 +616,10 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
unsigned long timeout = jiffies + time_left;
do {
- status = readl(iproc_i2c->base + IS_OFFSET) & ISR_MASK;
+ status = iproc_i2c_rd_reg(iproc_i2c,
+ IS_OFFSET) & ISR_MASK;
bcm_iproc_i2c_process_m_event(iproc_i2c, status);
- writel(status, iproc_i2c->base + IS_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IS_OFFSET, status);
if (time_after(jiffies, timeout)) {
time_left = 0;
@@ -623,7 +636,7 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
/* flush both TX/RX FIFOs */
val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
- writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
return -ETIMEDOUT;
}
@@ -631,7 +644,7 @@ static int bcm_iproc_i2c_xfer_wait(struct bcm_iproc_i2c_dev *iproc_i2c,
if (ret) {
/* flush both TX/RX FIFOs */
val = BIT(M_FIFO_RX_FLUSH_SHIFT) | BIT(M_FIFO_TX_FLUSH_SHIFT);
- writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, val);
return ret;
}
@@ -647,8 +660,8 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
unsigned int tx_bytes;
/* check if bus is busy */
- if (!!(readl(iproc_i2c->base + M_CMD_OFFSET) &
- BIT(M_CMD_START_BUSY_SHIFT))) {
+ if (!!(iproc_i2c_rd_reg(iproc_i2c,
+ M_CMD_OFFSET) & BIT(M_CMD_START_BUSY_SHIFT))) {
dev_warn(iproc_i2c->device, "bus is busy\n");
return -EBUSY;
}
@@ -657,7 +670,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
/* format and load slave address into the TX FIFO */
addr = i2c_8bit_addr_from_msg(msg);
- writel(addr, iproc_i2c->base + M_TX_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, addr);
/*
* For a write transaction, load data into the TX FIFO. Only allow
@@ -673,7 +686,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
if (i == msg->len - 1)
val |= 1 << M_TX_WR_STATUS_SHIFT;
- writel(val, iproc_i2c->base + M_TX_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_TX_OFFSET, val);
}
iproc_i2c->tx_bytes = tx_bytes;
}
@@ -713,10 +726,10 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
iproc_i2c->thld_bytes = msg->len;
/* set threshold value */
- tmp = readl(iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ tmp = iproc_i2c_rd_reg(iproc_i2c, M_FIFO_CTRL_OFFSET);
tmp &= ~(M_FIFO_RX_THLD_MASK << M_FIFO_RX_THLD_SHIFT);
tmp |= iproc_i2c->thld_bytes << M_FIFO_RX_THLD_SHIFT;
- writel(tmp, iproc_i2c->base + M_FIFO_CTRL_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, M_FIFO_CTRL_OFFSET, tmp);
/* enable the RX threshold interrupt */
val_intr_en |= BIT(IE_M_RX_THLD_SHIFT);
@@ -728,7 +741,7 @@ static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c,
}
if (iproc_i2c->irq)
- writel(val_intr_en, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, val_intr_en);
return bcm_iproc_i2c_xfer_wait(iproc_i2c, msg, val);
}
@@ -792,10 +805,10 @@ static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c)
}
iproc_i2c->bus_speed = bus_speed;
- val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
val |= (bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT;
- writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
dev_info(iproc_i2c->device, "bus set to %u Hz\n", bus_speed);
@@ -870,8 +883,8 @@ static int bcm_iproc_i2c_remove(struct platform_device *pdev)
* Make sure there's no pending interrupt when we remove the
* adapter
*/
- writel(0, iproc_i2c->base + IE_OFFSET);
- readl(iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
+ iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
synchronize_irq(iproc_i2c->irq);
}
@@ -892,8 +905,8 @@ static int bcm_iproc_i2c_suspend(struct device *dev)
* Make sure there's no pending interrupt when we go into
* suspend
*/
- writel(0, iproc_i2c->base + IE_OFFSET);
- readl(iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, 0);
+ iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
synchronize_irq(iproc_i2c->irq);
}
@@ -918,10 +931,10 @@ static int bcm_iproc_i2c_resume(struct device *dev)
return ret;
/* configure to the desired bus speed */
- val = readl(iproc_i2c->base + TIM_CFG_OFFSET);
+ val = iproc_i2c_rd_reg(iproc_i2c, TIM_CFG_OFFSET);
val &= ~(1 << TIM_CFG_MODE_400_SHIFT);
val |= (iproc_i2c->bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT;
- writel(val, iproc_i2c->base + TIM_CFG_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, TIM_CFG_OFFSET, val);
bcm_iproc_i2c_enable_disable(iproc_i2c, true);
@@ -965,15 +978,15 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)
iproc_i2c->slave = NULL;
/* disable all slave interrupts */
- tmp = readl(iproc_i2c->base + IE_OFFSET);
+ tmp = iproc_i2c_rd_reg(iproc_i2c, IE_OFFSET);
tmp &= ~(IE_S_ALL_INTERRUPT_MASK <<
IE_S_ALL_INTERRUPT_SHIFT);
- writel(tmp, iproc_i2c->base + IE_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, IE_OFFSET, tmp);
/* Erase the slave address programmed */
- tmp = readl(iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+ tmp = iproc_i2c_rd_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET);
tmp &= ~BIT(S_CFG_EN_NIC_SMB_ADDR3_SHIFT);
- writel(tmp, iproc_i2c->base + S_CFG_SMBUS_ADDR_OFFSET);
+ iproc_i2c_wr_reg(iproc_i2c, S_CFG_SMBUS_ADDR_OFFSET, tmp);
return 0;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
` (4 preceding siblings ...)
2019-02-04 23:15 ` [PATCH v4 5/8] i2c: iproc: use wrapper for read/write access Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-13 21:18 ` Rob Herring
2019-02-04 23:15 ` [PATCH v4 7/8] i2c: iproc: add NIC I2C support Ray Jui
2019-02-04 23:15 ` [PATCH v4 8/8] arm64: dts: Stingray: Add NIC i2c device node Ray Jui
7 siblings, 1 reply; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui
From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Update iProc I2C binding document to add new compatible string
"brcm,iproc-nic-i2c". Optional property "brcm,ape-hsls-addr-mask" is
also added that allows configuration of the host view into the APE's
address for "brcm,iproc-nic-i2c"
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
index d3a3620b1f06..02e82d20239e 100644
--- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
@@ -3,7 +3,7 @@ Broadcom iProc I2C controller
Required properties:
- compatible:
- Must be "brcm,iproc-i2c"
+ Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
- reg:
Define the base and range of the I/O address space that contain the iProc
@@ -24,6 +24,9 @@ Optional properties:
Should contain the I2C interrupt. If unspecified, driver will fall back to
polling mode
+- brcm,ape-hsls-addr-mask:
+ Required for "brcm,iproc-nic-i2c". Host view of address mask into the
+ 'APE' co-processor
Example:
i2c0: i2c@18008000 {
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* Re: [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
2019-02-04 23:15 ` [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string Ray Jui
@ 2019-02-13 21:18 ` Rob Herring
2019-02-13 22:09 ` Ray Jui
0 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2019-02-13 21:18 UTC (permalink / raw)
To: Ray Jui
Cc: Wolfram Sang, Mark Rutland, linux-i2c, devicetree,
linux-arm-kernel, linux-kernel, bcm-kernel-feedback-list,
Rayagonda Kokatanur
On Mon, Feb 04, 2019 at 03:15:52PM -0800, Ray Jui wrote:
> From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>
> Update iProc I2C binding document to add new compatible string
> "brcm,iproc-nic-i2c". Optional property "brcm,ape-hsls-addr-mask" is
> also added that allows configuration of the host view into the APE's
> address for "brcm,iproc-nic-i2c"
>
> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
> ---
> Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt | 5 ++++-
> 1 file changed, 4 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> index d3a3620b1f06..02e82d20239e 100644
> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> @@ -3,7 +3,7 @@ Broadcom iProc I2C controller
> Required properties:
>
> - compatible:
> - Must be "brcm,iproc-i2c"
> + Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
>
> - reg:
> Define the base and range of the I/O address space that contain the iProc
> @@ -24,6 +24,9 @@ Optional properties:
> Should contain the I2C interrupt. If unspecified, driver will fall back to
> polling mode
>
> +- brcm,ape-hsls-addr-mask:
> + Required for "brcm,iproc-nic-i2c". Host view of address mask into the
> + 'APE' co-processor
What's the data type and size? What are valid values?
>
> Example:
> i2c0: i2c@18008000 {
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
2019-02-13 21:18 ` Rob Herring
@ 2019-02-13 22:09 ` Ray Jui
2019-02-14 14:02 ` Rob Herring
0 siblings, 1 reply; 17+ messages in thread
From: Ray Jui @ 2019-02-13 22:09 UTC (permalink / raw)
To: Rob Herring
Cc: Wolfram Sang, Mark Rutland, linux-i2c, devicetree,
linux-arm-kernel, linux-kernel, bcm-kernel-feedback-list,
Rayagonda Kokatanur
On 2/13/2019 1:18 PM, Rob Herring wrote:
> On Mon, Feb 04, 2019 at 03:15:52PM -0800, Ray Jui wrote:
>> From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>>
>> Update iProc I2C binding document to add new compatible string
>> "brcm,iproc-nic-i2c". Optional property "brcm,ape-hsls-addr-mask" is
>> also added that allows configuration of the host view into the APE's
>> address for "brcm,iproc-nic-i2c"
>>
>> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
>> ---
>> Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt | 5 ++++-
>> 1 file changed, 4 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>> index d3a3620b1f06..02e82d20239e 100644
>> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>> @@ -3,7 +3,7 @@ Broadcom iProc I2C controller
>> Required properties:
>>
>> - compatible:
>> - Must be "brcm,iproc-i2c"
>> + Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
>>
>> - reg:
>> Define the base and range of the I/O address space that contain the iProc
>> @@ -24,6 +24,9 @@ Optional properties:
>> Should contain the I2C interrupt. If unspecified, driver will fall back to
>> polling mode
>>
>> +- brcm,ape-hsls-addr-mask:
>> + Required for "brcm,iproc-nic-i2c". Host view of address mask into the
>> + 'APE' co-processor
>
> What's the data type and size? What are valid values?
It's an unsigned u32 mask value. An example of a valid value is for
example 0x03400000. Do you want any of these added to the paragraph above?
>
>>
>> Example:
>> i2c0: i2c@18008000 {
>> --
>> 2.17.1
>>
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
2019-02-13 22:09 ` Ray Jui
@ 2019-02-14 14:02 ` Rob Herring
2019-02-14 17:36 ` Ray Jui
0 siblings, 1 reply; 17+ messages in thread
From: Rob Herring @ 2019-02-14 14:02 UTC (permalink / raw)
To: Ray Jui
Cc: Wolfram Sang, Mark Rutland, Linux I2C, devicetree,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
linux-kernel, maintainer:BROADCOM BCM7XXX ARM ARCHITECTURE,
Rayagonda Kokatanur
On Wed, Feb 13, 2019 at 4:09 PM Ray Jui <ray.jui@broadcom.com> wrote:
>
>
>
> On 2/13/2019 1:18 PM, Rob Herring wrote:
> > On Mon, Feb 04, 2019 at 03:15:52PM -0800, Ray Jui wrote:
> >> From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
> >>
> >> Update iProc I2C binding document to add new compatible string
> >> "brcm,iproc-nic-i2c". Optional property "brcm,ape-hsls-addr-mask" is
> >> also added that allows configuration of the host view into the APE's
> >> address for "brcm,iproc-nic-i2c"
> >>
> >> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
> >> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
> >> ---
> >> Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt | 5 ++++-
> >> 1 file changed, 4 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> >> index d3a3620b1f06..02e82d20239e 100644
> >> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> >> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
> >> @@ -3,7 +3,7 @@ Broadcom iProc I2C controller
> >> Required properties:
> >>
> >> - compatible:
> >> - Must be "brcm,iproc-i2c"
> >> + Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
> >>
> >> - reg:
> >> Define the base and range of the I/O address space that contain the iProc
> >> @@ -24,6 +24,9 @@ Optional properties:
> >> Should contain the I2C interrupt. If unspecified, driver will fall back to
> >> polling mode
> >>
> >> +- brcm,ape-hsls-addr-mask:
> >> + Required for "brcm,iproc-nic-i2c". Host view of address mask into the
> >> + 'APE' co-processor
> >
> > What's the data type and size? What are valid values?
>
> It's an unsigned u32 mask value. An example of a valid value is for
> example 0x03400000. Do you want any of these added to the paragraph above?
Yes. Bindings should define constraints.
Rob
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string
2019-02-14 14:02 ` Rob Herring
@ 2019-02-14 17:36 ` Ray Jui
0 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-14 17:36 UTC (permalink / raw)
To: Rob Herring
Cc: Wolfram Sang, Mark Rutland, Linux I2C, devicetree,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
linux-kernel, maintainer:BROADCOM BCM7XXX ARM ARCHITECTURE,
Rayagonda Kokatanur
On 2/14/2019 6:02 AM, Rob Herring wrote:
> On Wed, Feb 13, 2019 at 4:09 PM Ray Jui <ray.jui@broadcom.com> wrote:
>>
>>
>>
>> On 2/13/2019 1:18 PM, Rob Herring wrote:
>>> On Mon, Feb 04, 2019 at 03:15:52PM -0800, Ray Jui wrote:
>>>> From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>>>>
>>>> Update iProc I2C binding document to add new compatible string
>>>> "brcm,iproc-nic-i2c". Optional property "brcm,ape-hsls-addr-mask" is
>>>> also added that allows configuration of the host view into the APE's
>>>> address for "brcm,iproc-nic-i2c"
>>>>
>>>> Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
>>>> Signed-off-by: Ray Jui <ray.jui@broadcom.com>
>>>> ---
>>>> Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt | 5 ++++-
>>>> 1 file changed, 4 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>>>> index d3a3620b1f06..02e82d20239e 100644
>>>> --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>>>> +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
>>>> @@ -3,7 +3,7 @@ Broadcom iProc I2C controller
>>>> Required properties:
>>>>
>>>> - compatible:
>>>> - Must be "brcm,iproc-i2c"
>>>> + Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
>>>>
>>>> - reg:
>>>> Define the base and range of the I/O address space that contain the iProc
>>>> @@ -24,6 +24,9 @@ Optional properties:
>>>> Should contain the I2C interrupt. If unspecified, driver will fall back to
>>>> polling mode
>>>>
>>>> +- brcm,ape-hsls-addr-mask:
>>>> + Required for "brcm,iproc-nic-i2c". Host view of address mask into the
>>>> + 'APE' co-processor
>>>
>>> What's the data type and size? What are valid values?
>>
>> It's an unsigned u32 mask value. An example of a valid value is for
>> example 0x03400000. Do you want any of these added to the paragraph above?
>
> Yes. Bindings should define constraints.
Okay will do! Thanks.
>
> Rob
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v4 7/8] i2c: iproc: add NIC I2C support
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
` (5 preceding siblings ...)
2019-02-04 23:15 ` [PATCH v4 6/8] dt-bindings: i2c: iproc: add "brcm,iproc-nic-i2c" compatible string Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
2019-02-04 23:15 ` [PATCH v4 8/8] arm64: dts: Stingray: Add NIC i2c device node Ray Jui
7 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui
From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Add NIC I2C support to the iProc I2C driver. Access to the NIC I2C base
registers requires going through the IDM wrapper to map into the NIC's
address space
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
drivers/i2c/busses/i2c-bcm-iproc.c | 79 ++++++++++++++++++++++++++++--
1 file changed, 75 insertions(+), 4 deletions(-)
diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c
index 5b9cbd7a3776..9598e1d0048e 100644
--- a/drivers/i2c/busses/i2c-bcm-iproc.c
+++ b/drivers/i2c/busses/i2c-bcm-iproc.c
@@ -17,9 +17,11 @@
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
+#define IDM_CTRL_DIRECT_OFFSET 0x00
#define CFG_OFFSET 0x00
#define CFG_RESET_SHIFT 31
#define CFG_EN_SHIFT 30
@@ -174,11 +176,26 @@ enum bus_speed_index {
I2C_SPD_400K,
};
+enum bcm_iproc_i2c_type {
+ IPROC_I2C,
+ IPROC_I2C_NIC
+};
+
struct bcm_iproc_i2c_dev {
struct device *device;
+ enum bcm_iproc_i2c_type type;
int irq;
void __iomem *base;
+ void __iomem *idm_base;
+
+ u32 ape_addr_mask;
+
+ /* lock for indirect access through IDM */
+ spinlock_t idm_lock;
+
+ /* indicates no slave mode support */
+ bool no_slave;
struct i2c_adapter adapter;
unsigned int bus_speed;
@@ -215,13 +232,33 @@ static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c,
static inline u32 iproc_i2c_rd_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 offset)
{
- return readl(iproc_i2c->base + offset);
+ u32 val;
+
+ if (iproc_i2c->idm_base) {
+ spin_lock(&iproc_i2c->idm_lock);
+ writel(iproc_i2c->ape_addr_mask,
+ iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
+ val = readl(iproc_i2c->base + offset);
+ spin_unlock(&iproc_i2c->idm_lock);
+ } else {
+ val = readl(iproc_i2c->base + offset);
+ }
+
+ return val;
}
static inline void iproc_i2c_wr_reg(struct bcm_iproc_i2c_dev *iproc_i2c,
u32 offset, u32 val)
{
- writel(val, iproc_i2c->base + offset);
+ if (iproc_i2c->idm_base) {
+ spin_lock(&iproc_i2c->idm_lock);
+ writel(iproc_i2c->ape_addr_mask,
+ iproc_i2c->idm_base + IDM_CTRL_DIRECT_OFFSET);
+ writel(val, iproc_i2c->base + offset);
+ spin_unlock(&iproc_i2c->idm_lock);
+ } else {
+ writel(val, iproc_i2c->base + offset);
+ }
}
static void bcm_iproc_i2c_slave_init(
@@ -766,7 +803,13 @@ static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter,
static uint32_t bcm_iproc_i2c_functionality(struct i2c_adapter *adap)
{
- return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SLAVE;
+ struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(adap);
+ u32 val = I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+
+ if (!iproc_i2c->no_slave)
+ val |= I2C_FUNC_SLAVE;
+
+ return val;
}
static const struct i2c_algorithm bcm_iproc_algo = {
@@ -829,6 +872,8 @@ static int bcm_iproc_i2c_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, iproc_i2c);
iproc_i2c->device = &pdev->dev;
+ iproc_i2c->type =
+ (enum bcm_iproc_i2c_type) of_device_get_match_data(&pdev->dev);
init_completion(&iproc_i2c->done);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -836,6 +881,26 @@ static int bcm_iproc_i2c_probe(struct platform_device *pdev)
if (IS_ERR(iproc_i2c->base))
return PTR_ERR(iproc_i2c->base);
+ if (iproc_i2c->type == IPROC_I2C_NIC) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ iproc_i2c->idm_base = devm_ioremap_resource(iproc_i2c->device,
+ res);
+ if (IS_ERR(iproc_i2c->idm_base))
+ return PTR_ERR(iproc_i2c->idm_base);
+
+ ret = of_property_read_u32(iproc_i2c->device->of_node,
+ "brcm,ape-hsls-addr-mask",
+ &iproc_i2c->ape_addr_mask);
+ if (ret < 0) {
+ dev_err(iproc_i2c->device,
+ "'brcm,ape-hsls-addr-mask' missing\n");
+ return -EINVAL;
+ }
+
+ spin_lock_init(&iproc_i2c->idm_lock);
+ iproc_i2c->no_slave = true;
+ }
+
ret = bcm_iproc_i2c_init(iproc_i2c);
if (ret)
return ret;
@@ -992,7 +1057,13 @@ static int bcm_iproc_i2c_unreg_slave(struct i2c_client *slave)
}
static const struct of_device_id bcm_iproc_i2c_of_match[] = {
- { .compatible = "brcm,iproc-i2c" },
+ {
+ .compatible = "brcm,iproc-i2c",
+ .data = (int *)IPROC_I2C,
+ }, {
+ .compatible = "brcm,iproc-nic-i2c",
+ .data = (int *)IPROC_I2C_NIC,
+ },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, bcm_iproc_i2c_of_match);
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v4 8/8] arm64: dts: Stingray: Add NIC i2c device node
2019-02-04 23:15 [PATCH v4 0/8] iProc I2C slave mode and NIC mode Ray Jui
` (6 preceding siblings ...)
2019-02-04 23:15 ` [PATCH v4 7/8] i2c: iproc: add NIC I2C support Ray Jui
@ 2019-02-04 23:15 ` Ray Jui
7 siblings, 0 replies; 17+ messages in thread
From: Ray Jui @ 2019-02-04 23:15 UTC (permalink / raw)
To: Wolfram Sang, Rob Herring, Mark Rutland
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-kernel,
bcm-kernel-feedback-list, Rayagonda Kokatanur, Ray Jui
From: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Add NIC i2c device node.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
---
.../boot/dts/broadcom/stingray/stingray.dtsi | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index cfeaa855bd05..67e53768a84a 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -612,4 +612,22 @@
status = "disabled";
};
};
+
+ nic-hsls {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x7fffffff>;
+
+ nic_i2c0: i2c@60826100 {
+ compatible = "brcm,iproc-nic-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x60826100 0x100>,
+ <0x60e00408 0x1000>;
+ brcm,ape-hsls-addr-mask = <0x03400000>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+ };
};
--
2.17.1
^ permalink raw reply related [flat|nested] 17+ messages in thread