[PATCH v2 0/5] phy: tegra: xusb: Add Tegra186 support

[PATCH v2 0/5] phy: tegra: xusb: Add Tegra186 support

[Thierry Reding]

From: Thierry Reding <treding@nvidia.com>

This series adds support for Tegra186 to the XUSB pad controller driver.
Patch 1 extends the device tree bindings with support for Tegra186 while
patches 2-4 are preparatory work for the final patch 5 that adds the
Tegra186 specific programming for the UPHY blocks.

Changes in v2:
- address review comments from Kishon
- added Reviewed-by tags from JC

Thierry

JC Kuo (2):
  phy: tegra: xusb: Skip single function lane programming
  phy: tegra: xusb: Add Tegra186 support

Thierry Reding (3):
  dt-bindings: phy: tegra: Add Tegra186 support
  phy: tegra: xusb: Parse dual-role mode property
  phy: tegra: xusb: Add support for power supplies

 .../phy/nvidia,tegra124-xusb-padctl.txt       |   9 +
 MAINTAINERS                                   |   5 +
 drivers/phy/tegra/Makefile                    |   1 +
 drivers/phy/tegra/xusb-tegra186.c             | 899 ++++++++++++++++++
 drivers/phy/tegra/xusb.c                      |  67 +-
 drivers/phy/tegra/xusb.h                      |  35 +
 6 files changed, 1014 insertions(+), 2 deletions(-)
 create mode 100644 drivers/phy/tegra/xusb-tegra186.c

-- 
2.20.1

[PATCH v2 1/5] dt-bindings: phy: tegra: Add Tegra186 support

[Thierry Reding]

From: Thierry Reding <treding@nvidia.com>

Extend the bindings to cover the set of features found in Tegra186. Note
that, technically, there are four more supplies connected to the XUSB
pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL), but
the power sequencing requirements of Tegra186 require these to be under
the control of the PMIC.

Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
 .../bindings/phy/nvidia,tegra124-xusb-padctl.txt         | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
index 3742c152c467..daedb15f322e 100644
--- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
+++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
@@ -36,11 +36,20 @@ Required properties:
   - Tegra124: "nvidia,tegra124-xusb-padctl"
   - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
   - Tegra210: "nvidia,tegra210-xusb-padctl"
+  - Tegra186: "nvidia,tegra186-xusb-padctl"
 - reg: Physical base address and length of the controller's registers.
 - resets: Must contain an entry for each entry in reset-names.
 - reset-names: Must include the following entries:
   - "padctl"
 
+For Tegra186:
+- avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY
+  power supply. Must supply 1.8 V.
+- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
+  3.3 V.
+- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
+- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
+
 
 Pad nodes:
 ==========
-- 
2.20.1

[PATCH v2 2/5] phy: tegra: xusb: Skip single function lane programming

[Thierry Reding]

From: JC Kuo <jckuo@nvidia.com>

Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
 drivers/phy/tegra/xusb.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/tegra/xusb.c b/drivers/phy/tegra/xusb.c
index 5b3b8863363e..e3bc60cfe6a1 100644
--- a/drivers/phy/tegra/xusb.c
+++ b/drivers/phy/tegra/xusb.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (c) 2014-2015, NVIDIA CORPORATION.  All rights reserved.
+ * Copyright (c) 2014-2016, NVIDIA CORPORATION.  All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -313,6 +313,10 @@ static void tegra_xusb_lane_program(struct tegra_xusb_lane *lane)
 	const struct tegra_xusb_lane_soc *soc = lane->soc;
 	u32 value;
 
+	/* skip single function lanes */
+	if (soc->num_funcs < 2)
+		return;
+
 	/* choose function */
 	value = padctl_readl(padctl, soc->offset);
 	value &= ~(soc->mask << soc->shift);
-- 
2.20.1

[PATCH v2 3/5] phy: tegra: xusb: Parse dual-role mode property

[Thierry Reding]

From: Thierry Reding <treding@nvidia.com>

The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.

Based on work by JC Kuo <jckuo@nvidia.com>.

Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
 drivers/phy/tegra/xusb.c | 21 +++++++++++++++++++++
 drivers/phy/tegra/xusb.h |  3 +++
 2 files changed, 24 insertions(+)

diff --git a/drivers/phy/tegra/xusb.c b/drivers/phy/tegra/xusb.c
index e3bc60cfe6a1..57a2d08ef6da 100644
--- a/drivers/phy/tegra/xusb.c
+++ b/drivers/phy/tegra/xusb.c
@@ -546,13 +546,34 @@ static void tegra_xusb_port_unregister(struct tegra_xusb_port *port)
 	device_unregister(&port->dev);
 }
 
+static const char *const modes[] = {
+	[USB_DR_MODE_UNKNOWN] = "",
+	[USB_DR_MODE_HOST] = "host",
+	[USB_DR_MODE_PERIPHERAL] = "peripheral",
+	[USB_DR_MODE_OTG] = "otg",
+};
+
 static int tegra_xusb_usb2_port_parse_dt(struct tegra_xusb_usb2_port *usb2)
 {
 	struct tegra_xusb_port *port = &usb2->base;
 	struct device_node *np = port->dev.of_node;
+	const char *mode;
 
 	usb2->internal = of_property_read_bool(np, "nvidia,internal");
 
+	if (!of_property_read_string(np, "mode", &mode)) {
+		int err = match_string(modes, ARRAY_SIZE(modes), mode);
+		if (err < 0) {
+			dev_err(&port->dev, "invalid value %s for \"mode\"\n",
+				mode);
+			usb2->mode = USB_DR_MODE_UNKNOWN;
+		} else {
+			usb2->mode = err;
+		}
+	} else {
+		usb2->mode = USB_DR_MODE_HOST;
+	}
+
 	usb2->supply = devm_regulator_get(&port->dev, "vbus");
 	return PTR_ERR_OR_ZERO(usb2->supply);
 }
diff --git a/drivers/phy/tegra/xusb.h b/drivers/phy/tegra/xusb.h
index b49dbc36efa3..bb60fc09c752 100644
--- a/drivers/phy/tegra/xusb.h
+++ b/drivers/phy/tegra/xusb.h
@@ -19,6 +19,8 @@
 #include <linux/mutex.h>
 #include <linux/workqueue.h>
 
+#include <linux/usb/otg.h>
+
 /* legacy entry points for backwards-compatibility */
 int tegra_xusb_padctl_legacy_probe(struct platform_device *pdev);
 int tegra_xusb_padctl_legacy_remove(struct platform_device *pdev);
@@ -271,6 +273,7 @@ struct tegra_xusb_usb2_port {
 	struct tegra_xusb_port base;
 
 	struct regulator *supply;
+	enum usb_dr_mode mode;
 	bool internal;
 };
 
-- 
2.20.1

[PATCH v2 4/5] phy: tegra: xusb: Add support for power supplies

[Thierry Reding]

From: Thierry Reding <treding@nvidia.com>

Support enabling various supplies needed to provide power to the PLLs
and logic used to drive the USB, PCI and SATA pads.

Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
 drivers/phy/tegra/xusb.c | 34 +++++++++++++++++++++++++++++++++-
 drivers/phy/tegra/xusb.h |  5 +++++
 2 files changed, 38 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/tegra/xusb.c b/drivers/phy/tegra/xusb.c
index 57a2d08ef6da..e510629f4f1c 100644
--- a/drivers/phy/tegra/xusb.c
+++ b/drivers/phy/tegra/xusb.c
@@ -864,6 +864,7 @@ static int tegra_xusb_padctl_probe(struct platform_device *pdev)
 	struct tegra_xusb_padctl *padctl;
 	const struct of_device_id *match;
 	struct resource *res;
+	unsigned int i;
 	int err;
 
 	/* for backwards compatibility with old device trees */
@@ -901,14 +902,38 @@ static int tegra_xusb_padctl_probe(struct platform_device *pdev)
 		goto remove;
 	}
 
+	padctl->supplies = devm_kcalloc(&pdev->dev, padctl->soc->num_supplies,
+					sizeof(*padctl->supplies), GFP_KERNEL);
+	if (!padctl->supplies) {
+		err = -ENOMEM;
+		goto remove;
+	}
+
+	for (i = 0; i < padctl->soc->num_supplies; i++)
+		padctl->supplies[i].supply = padctl->soc->supply_names[i];
+
+	err = devm_regulator_bulk_get(&pdev->dev, padctl->soc->num_supplies,
+				      padctl->supplies);
+	if (err < 0) {
+		dev_err(&pdev->dev, "failed to get regulators: %d\n", err);
+		goto remove;
+	}
+
 	err = reset_control_deassert(padctl->rst);
 	if (err < 0)
 		goto remove;
 
+	err = regulator_bulk_enable(padctl->soc->num_supplies,
+				    padctl->supplies);
+	if (err < 0) {
+		dev_err(&pdev->dev, "failed to enable supplies: %d\n", err);
+		goto reset;
+	}
+
 	err = tegra_xusb_setup_pads(padctl);
 	if (err < 0) {
 		dev_err(&pdev->dev, "failed to setup pads: %d\n", err);
-		goto reset;
+		goto power_down;
 	}
 
 	err = tegra_xusb_setup_ports(padctl);
@@ -921,6 +946,8 @@ static int tegra_xusb_padctl_probe(struct platform_device *pdev)
 
 remove_pads:
 	tegra_xusb_remove_pads(padctl);
+power_down:
+	regulator_bulk_disable(padctl->soc->num_supplies, padctl->supplies);
 reset:
 	reset_control_assert(padctl->rst);
 remove:
@@ -936,6 +963,11 @@ static int tegra_xusb_padctl_remove(struct platform_device *pdev)
 	tegra_xusb_remove_ports(padctl);
 	tegra_xusb_remove_pads(padctl);
 
+	err = regulator_bulk_disable(padctl->soc->num_supplies,
+				     padctl->supplies);
+	if (err < 0)
+		dev_err(&pdev->dev, "failed to disable supplies: %d\n", err);
+
 	err = reset_control_assert(padctl->rst);
 	if (err < 0)
 		dev_err(&pdev->dev, "failed to assert reset: %d\n", err);
diff --git a/drivers/phy/tegra/xusb.h b/drivers/phy/tegra/xusb.h
index bb60fc09c752..5d5d22f6cb41 100644
--- a/drivers/phy/tegra/xusb.h
+++ b/drivers/phy/tegra/xusb.h
@@ -370,6 +370,9 @@ struct tegra_xusb_padctl_soc {
 	} ports;
 
 	const struct tegra_xusb_padctl_ops *ops;
+
+	const char * const *supply_names;
+	unsigned int num_supplies;
 };
 
 struct tegra_xusb_padctl {
@@ -393,6 +396,8 @@ struct tegra_xusb_padctl {
 	unsigned int enable;
 
 	struct clk *clk;
+
+	struct regulator_bulk_data *supplies;
 };
 
 static inline void padctl_writel(struct tegra_xusb_padctl *padctl, u32 value,
-- 
2.20.1

[PATCH v2 5/5] phy: tegra: xusb: Add Tegra186 support

[Thierry Reding]

From: JC Kuo <jckuo@nvidia.com>

Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.

Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v2:
- use SPDX-License-Identifier and remove license text
- remove unnecessary parentheses
- use BIT() where appropriate

 MAINTAINERS                       |   5 +
 drivers/phy/tegra/Makefile        |   1 +
 drivers/phy/tegra/xusb-tegra186.c | 899 ++++++++++++++++++++++++++++++
 drivers/phy/tegra/xusb.c          |   6 +
 drivers/phy/tegra/xusb.h          |  27 +
 5 files changed, 938 insertions(+)
 create mode 100644 drivers/phy/tegra/xusb-tegra186.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 8b53eb3db271..183283ea7ea1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15274,6 +15274,11 @@ M:	Laxman Dewangan <ldewangan@nvidia.com>
 S:	Supported
 F:	drivers/spi/spi-tegra*
 
+TEGRA XUSB PADCTL DRIVER
+M:	JC Kuo <jckuo@nvidia.com>
+S:	Supported
+F:	drivers/phy/tegra/xusb*
+
 TEHUTI ETHERNET DRIVER
 M:	Andy Gospodarek <andy@greyhouse.net>
 L:	netdev@vger.kernel.org
diff --git a/drivers/phy/tegra/Makefile b/drivers/phy/tegra/Makefile
index 898589238fd9..a93cd9a499b2 100644
--- a/drivers/phy/tegra/Makefile
+++ b/drivers/phy/tegra/Makefile
@@ -4,3 +4,4 @@ phy-tegra-xusb-y += xusb.o
 phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_124_SOC) += xusb-tegra124.o
 phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_132_SOC) += xusb-tegra124.o
 phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_210_SOC) += xusb-tegra210.o
+phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_186_SOC) += xusb-tegra186.o
diff --git a/drivers/phy/tegra/xusb-tegra186.c b/drivers/phy/tegra/xusb-tegra186.c
new file mode 100644
index 000000000000..11ad6e4e4711
--- /dev/null
+++ b/drivers/phy/tegra/xusb-tegra186.c
@@ -0,0 +1,899 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2016-2019, NVIDIA CORPORATION.  All rights reserved.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/regulator/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+
+#include <soc/tegra/fuse.h>
+
+#include "xusb.h"
+
+/* FUSE USB_CALIB registers */
+#define HS_CURR_LEVEL_PADX_SHIFT(x)	((x) ? (11 + (x - 1) * 6) : 0)
+#define HS_CURR_LEVEL_PAD_MASK		0x3f
+#define HS_TERM_RANGE_ADJ_SHIFT		7
+#define HS_TERM_RANGE_ADJ_MASK		0xf
+#define HS_SQUELCH_SHIFT		29
+#define HS_SQUELCH_MASK			0x7
+
+#define RPD_CTRL_SHIFT			0
+#define RPD_CTRL_MASK			0x1f
+
+/* XUSB PADCTL registers */
+#define XUSB_PADCTL_USB2_PAD_MUX	0x4
+#define  USB2_PORT_SHIFT(x)		((x) * 2)
+#define  USB2_PORT_MASK			0x3
+#define   PORT_XUSB			1
+#define  HSIC_PORT_SHIFT(x)		((x) + 20)
+#define  HSIC_PORT_MASK			0x1
+#define   PORT_HSIC			0
+
+#define XUSB_PADCTL_USB2_PORT_CAP	0x8
+#define XUSB_PADCTL_SS_PORT_CAP		0xc
+#define  PORTX_CAP_SHIFT(x)		((x) * 4)
+#define  PORT_CAP_MASK			0x3
+#define   PORT_CAP_DISABLED		0x0
+#define   PORT_CAP_HOST			0x1
+#define   PORT_CAP_DEVICE		0x2
+#define   PORT_CAP_OTG			0x3
+
+#define XUSB_PADCTL_ELPG_PROGRAM		0x20
+#define  USB2_PORT_WAKE_INTERRUPT_ENABLE(x)		BIT(x)
+#define  USB2_PORT_WAKEUP_EVENT(x)			BIT((x) +  7)
+#define  SS_PORT_WAKE_INTERRUPT_ENABLE(x)		BIT((x) + 14)
+#define  SS_PORT_WAKEUP_EVENT(x)			BIT((x) + 21)
+#define  USB2_HSIC_PORT_WAKE_INTERRUPT_ENABLE(x)	BIT((x) + 28)
+#define  USB2_HSIC_PORT_WAKEUP_EVENT(x)			BIT((x) + 30)
+#define  ALL_WAKE_EVENTS						\
+	(USB2_PORT_WAKEUP_EVENT(0) | USB2_PORT_WAKEUP_EVENT(1) |	\
+	USB2_PORT_WAKEUP_EVENT(2) | SS_PORT_WAKEUP_EVENT(0) |		\
+	SS_PORT_WAKEUP_EVENT(1) | SS_PORT_WAKEUP_EVENT(2) |		\
+	USB2_HSIC_PORT_WAKEUP_EVENT(0))
+
+#define XUSB_PADCTL_ELPG_PROGRAM_1		0x24
+#define  SSPX_ELPG_CLAMP_EN(x)			BIT(0 + (x) * 3)
+#define  SSPX_ELPG_CLAMP_EN_EARLY(x)		BIT(1 + (x) * 3)
+#define  SSPX_ELPG_VCORE_DOWN(x)		BIT(2 + (x) * 3)
+
+#define XUSB_PADCTL_USB2_OTG_PADX_CTL0(x)	(0x88 + (x) * 0x40)
+#define  HS_CURR_LEVEL(x)			((x) & 0x3f)
+#define  TERM_SEL				BIT(25)
+#define  USB2_OTG_PD				BIT(26)
+#define  USB2_OTG_PD2				BIT(27)
+#define  USB2_OTG_PD2_OVRD_EN			BIT(28)
+#define  USB2_OTG_PD_ZI				BIT(29)
+
+#define XUSB_PADCTL_USB2_OTG_PADX_CTL1(x)	(0x8c + (x) * 0x40)
+#define  USB2_OTG_PD_DR				BIT(2)
+#define  TERM_RANGE_ADJ(x)			(((x) & 0xf) << 3)
+#define  RPD_CTRL(x)				(((x) & 0x1f) << 26)
+
+#define XUSB_PADCTL_USB2_BIAS_PAD_CTL0		0x284
+#define  BIAS_PAD_PD				BIT(11)
+#define  HS_SQUELCH_LEVEL(x)			(((x) & 0x7) << 0)
+
+#define XUSB_PADCTL_USB2_BIAS_PAD_CTL1		0x288
+#define  USB2_TRK_START_TIMER(x)		(((x) & 0x7f) << 12)
+#define  USB2_TRK_DONE_RESET_TIMER(x)		(((x) & 0x7f) << 19)
+#define  USB2_PD_TRK				BIT(26)
+
+#define XUSB_PADCTL_HSIC_PADX_CTL0(x)		(0x300 + (x) * 0x20)
+#define  HSIC_PD_TX_DATA0			BIT(1)
+#define  HSIC_PD_TX_STROBE			BIT(3)
+#define  HSIC_PD_RX_DATA0			BIT(4)
+#define  HSIC_PD_RX_STROBE			BIT(6)
+#define  HSIC_PD_ZI_DATA0			BIT(7)
+#define  HSIC_PD_ZI_STROBE			BIT(9)
+#define  HSIC_RPD_DATA0				BIT(13)
+#define  HSIC_RPD_STROBE			BIT(15)
+#define  HSIC_RPU_DATA0				BIT(16)
+#define  HSIC_RPU_STROBE			BIT(18)
+
+#define XUSB_PADCTL_HSIC_PAD_TRK_CTL0		0x340
+#define  HSIC_TRK_START_TIMER(x)		(((x) & 0x7f) << 5)
+#define  HSIC_TRK_DONE_RESET_TIMER(x)		(((x) & 0x7f) << 12)
+#define  HSIC_PD_TRK				BIT(19)
+
+#define USB2_VBUS_ID				0x360
+#define  VBUS_OVERRIDE				BIT(14)
+#define  ID_OVERRIDE(x)				(((x) & 0xf) << 18)
+#define  ID_OVERRIDE_FLOATING			ID_OVERRIDE(8)
+#define  ID_OVERRIDE_GROUNDED			ID_OVERRIDE(0)
+
+#define TEGRA186_LANE(_name, _offset, _shift, _mask, _type)		\
+	{								\
+		.name = _name,						\
+		.offset = _offset,					\
+		.shift = _shift,					\
+		.mask = _mask,						\
+		.num_funcs = ARRAY_SIZE(tegra186_##_type##_functions),	\
+		.funcs = tegra186_##_type##_functions,			\
+	}
+
+struct tegra_xusb_fuse_calibration {
+	u32 *hs_curr_level;
+	u32 hs_squelch;
+	u32 hs_term_range_adj;
+	u32 rpd_ctrl;
+};
+
+struct tegra186_xusb_padctl {
+	struct tegra_xusb_padctl base;
+
+	struct tegra_xusb_fuse_calibration calib;
+
+	/* UTMI bias and tracking */
+	struct clk *usb2_trk_clk;
+	unsigned int bias_pad_enable;
+};
+
+static inline struct tegra186_xusb_padctl *
+to_tegra186_xusb_padctl(struct tegra_xusb_padctl *padctl)
+{
+	return container_of(padctl, struct tegra186_xusb_padctl, base);
+}
+
+/* USB 2.0 UTMI PHY support */
+static struct tegra_xusb_lane *
+tegra186_usb2_lane_probe(struct tegra_xusb_pad *pad, struct device_node *np,
+			 unsigned int index)
+{
+	struct tegra_xusb_usb2_lane *usb2;
+	int err;
+
+	usb2 = kzalloc(sizeof(*usb2), GFP_KERNEL);
+	if (!usb2)
+		return ERR_PTR(-ENOMEM);
+
+	INIT_LIST_HEAD(&usb2->base.list);
+	usb2->base.soc = &pad->soc->lanes[index];
+	usb2->base.index = index;
+	usb2->base.pad = pad;
+	usb2->base.np = np;
+
+	err = tegra_xusb_lane_parse_dt(&usb2->base, np);
+	if (err < 0) {
+		kfree(usb2);
+		return ERR_PTR(err);
+	}
+
+	return &usb2->base;
+}
+
+static void tegra186_usb2_lane_remove(struct tegra_xusb_lane *lane)
+{
+	struct tegra_xusb_usb2_lane *usb2 = to_usb2_lane(lane);
+
+	kfree(usb2);
+}
+
+static const struct tegra_xusb_lane_ops tegra186_usb2_lane_ops = {
+	.probe = tegra186_usb2_lane_probe,
+	.remove = tegra186_usb2_lane_remove,
+};
+
+static void tegra186_utmi_bias_pad_power_on(struct tegra_xusb_padctl *padctl)
+{
+	struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
+	struct device *dev = padctl->dev;
+	u32 value;
+	int err;
+
+	mutex_lock(&padctl->lock);
+
+	if (priv->bias_pad_enable++ > 0) {
+		mutex_unlock(&padctl->lock);
+		return;
+	}
+
+	err = clk_prepare_enable(priv->usb2_trk_clk);
+	if (err < 0)
+		dev_warn(dev, "failed to enable USB2 trk clock: %d\n", err);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+	value &= ~USB2_TRK_START_TIMER(~0);
+	value |= USB2_TRK_START_TIMER(0x1e);
+	value &= ~USB2_TRK_DONE_RESET_TIMER(~0);
+	value |= USB2_TRK_DONE_RESET_TIMER(0xa);
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL0);
+	value &= ~BIAS_PAD_PD;
+	value &= ~HS_SQUELCH_LEVEL(~0);
+	value |= HS_SQUELCH_LEVEL(priv->calib.hs_squelch);
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL0);
+
+	udelay(1);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+	value &= ~USB2_PD_TRK;
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+
+	mutex_unlock(&padctl->lock);
+}
+
+static void tegra186_utmi_bias_pad_power_off(struct tegra_xusb_padctl *padctl)
+{
+	struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
+	u32 value;
+
+	mutex_lock(&padctl->lock);
+
+	if (WARN_ON(priv->bias_pad_enable == 0)) {
+		mutex_unlock(&padctl->lock);
+		return;
+	}
+
+	if (--priv->bias_pad_enable > 0) {
+		mutex_unlock(&padctl->lock);
+		return;
+	}
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+	value |= USB2_PD_TRK;
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
+
+	clk_disable_unprepare(priv->usb2_trk_clk);
+
+	mutex_unlock(&padctl->lock);
+}
+
+void tegra_phy_xusb_utmi_pad_power_on(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	struct tegra_xusb_usb2_port *port;
+	struct device *dev = padctl->dev;
+	unsigned int index = lane->index;
+	u32 value;
+
+	if (!phy)
+		return;
+
+	port = tegra_xusb_find_usb2_port(padctl, index);
+	if (!port) {
+		dev_err(dev, "no port found for USB2 lane %u\n", index);
+		return;
+	}
+
+	tegra186_utmi_bias_pad_power_on(padctl);
+
+	udelay(2);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
+	value &= ~USB2_OTG_PD;
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
+	value &= ~USB2_OTG_PD_DR;
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
+}
+
+void tegra_phy_xusb_utmi_pad_power_down(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	unsigned int index = lane->index;
+	u32 value;
+
+	if (!phy)
+		return;
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
+	value |= USB2_OTG_PD;
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
+	value |= USB2_OTG_PD_DR;
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
+
+	udelay(2);
+
+	tegra186_utmi_bias_pad_power_off(padctl);
+}
+
+static int tegra186_utmi_phy_power_on(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_usb2_lane *usb2 = to_usb2_lane(lane);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
+	struct tegra_xusb_usb2_port *port;
+	unsigned int index = lane->index;
+	struct device *dev = padctl->dev;
+	u32 value;
+
+	port = tegra_xusb_find_usb2_port(padctl, index);
+	if (!port) {
+		dev_err(dev, "no port found for USB2 lane %u\n", index);
+		return -ENODEV;
+	}
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_PAD_MUX);
+	value &= ~(USB2_PORT_MASK << USB2_PORT_SHIFT(index));
+	value |= (PORT_XUSB << USB2_PORT_SHIFT(index));
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_PAD_MUX);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_PORT_CAP);
+	value &= ~(PORT_CAP_MASK << PORTX_CAP_SHIFT(index));
+
+	if (port->mode == USB_DR_MODE_UNKNOWN)
+		value |= (PORT_CAP_DISABLED << PORTX_CAP_SHIFT(index));
+	else if (port->mode == USB_DR_MODE_PERIPHERAL)
+		value |= (PORT_CAP_DEVICE << PORTX_CAP_SHIFT(index));
+	else if (port->mode == USB_DR_MODE_HOST)
+		value |= (PORT_CAP_HOST << PORTX_CAP_SHIFT(index));
+	else if (port->mode == USB_DR_MODE_OTG)
+		value |= (PORT_CAP_OTG << PORTX_CAP_SHIFT(index));
+
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_PORT_CAP);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
+	value &= ~USB2_OTG_PD_ZI;
+	value |= TERM_SEL;
+	value &= ~HS_CURR_LEVEL(~0);
+
+	if (usb2->hs_curr_level_offset) {
+		int hs_current_level;
+
+		hs_current_level = (int)priv->calib.hs_curr_level[index] +
+						usb2->hs_curr_level_offset;
+
+		if (hs_current_level < 0)
+			hs_current_level = 0;
+		if (hs_current_level > 0x3f)
+			hs_current_level = 0x3f;
+
+		value |= HS_CURR_LEVEL(hs_current_level);
+	} else {
+		value |= HS_CURR_LEVEL(priv->calib.hs_curr_level[index]);
+	}
+
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
+
+	value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
+	value &= ~TERM_RANGE_ADJ(~0);
+	value |= TERM_RANGE_ADJ(priv->calib.hs_term_range_adj);
+	value &= ~RPD_CTRL(~0);
+	value |= RPD_CTRL(priv->calib.rpd_ctrl);
+	padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
+
+	/* TODO: pad power saving */
+	tegra_phy_xusb_utmi_pad_power_on(phy);
+	return 0;
+}
+
+static int tegra186_utmi_phy_power_off(struct phy *phy)
+{
+	/* TODO: pad power saving */
+	tegra_phy_xusb_utmi_pad_power_down(phy);
+
+	return 0;
+}
+
+static int tegra186_utmi_phy_init(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	struct tegra_xusb_usb2_port *port;
+	unsigned int index = lane->index;
+	struct device *dev = padctl->dev;
+	int err;
+
+	port = tegra_xusb_find_usb2_port(padctl, index);
+	if (!port) {
+		dev_err(dev, "no port found for USB2 lane %u\n", index);
+		return -ENODEV;
+	}
+
+	if (port->supply && port->mode == USB_DR_MODE_HOST) {
+		err = regulator_enable(port->supply);
+		if (err) {
+			dev_err(dev, "failed to enable port %u VBUS: %d\n",
+				index, err);
+			return err;
+		}
+	}
+
+	return 0;
+}
+
+static int tegra186_utmi_phy_exit(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	struct tegra_xusb_usb2_port *port;
+	unsigned int index = lane->index;
+	struct device *dev = padctl->dev;
+	int err;
+
+	port = tegra_xusb_find_usb2_port(padctl, index);
+	if (!port) {
+		dev_err(dev, "no port found for USB2 lane %u\n", index);
+		return -ENODEV;
+	}
+
+	if (port->supply && port->mode == USB_DR_MODE_HOST) {
+		err = regulator_disable(port->supply);
+		if (err) {
+			dev_err(dev, "failed to disable port %u VBUS: %d\n",
+				index, err);
+			return err;
+		}
+	}
+
+	return 0;
+}
+
+static const struct phy_ops utmi_phy_ops = {
+	.init = tegra186_utmi_phy_init,
+	.exit = tegra186_utmi_phy_exit,
+	.power_on = tegra186_utmi_phy_power_on,
+	.power_off = tegra186_utmi_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static struct tegra_xusb_pad *
+tegra186_usb2_pad_probe(struct tegra_xusb_padctl *padctl,
+			const struct tegra_xusb_pad_soc *soc,
+			struct device_node *np)
+{
+	struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
+	struct tegra_xusb_usb2_pad *usb2;
+	struct tegra_xusb_pad *pad;
+	int err;
+
+	usb2 = kzalloc(sizeof(*usb2), GFP_KERNEL);
+	if (!usb2)
+		return ERR_PTR(-ENOMEM);
+
+	pad = &usb2->base;
+	pad->ops = &tegra186_usb2_lane_ops;
+	pad->soc = soc;
+
+	err = tegra_xusb_pad_init(pad, padctl, np);
+	if (err < 0) {
+		kfree(usb2);
+		goto out;
+	}
+
+	priv->usb2_trk_clk = devm_clk_get(&pad->dev, "trk");
+	if (IS_ERR(usb2->clk)) {
+		err = PTR_ERR(usb2->clk);
+		dev_dbg(&pad->dev, "failed to get usb2 trk clock: %d\n", err);
+		goto unregister;
+	}
+
+	err = tegra_xusb_pad_register(pad, &utmi_phy_ops);
+	if (err < 0)
+		goto unregister;
+
+	dev_set_drvdata(&pad->dev, pad);
+
+	return pad;
+
+unregister:
+	device_unregister(&pad->dev);
+out:
+	return ERR_PTR(err);
+}
+
+static void tegra186_usb2_pad_remove(struct tegra_xusb_pad *pad)
+{
+	struct tegra_xusb_usb2_pad *usb2 = to_usb2_pad(pad);
+
+	kfree(usb2);
+}
+
+static const struct tegra_xusb_pad_ops tegra186_usb2_pad_ops = {
+	.probe = tegra186_usb2_pad_probe,
+	.remove = tegra186_usb2_pad_remove,
+};
+
+static const char * const tegra186_usb2_functions[] = {
+	"xusb",
+};
+
+static const struct tegra_xusb_lane_soc tegra186_usb2_lanes[] = {
+	TEGRA186_LANE("usb2-0", 0,  0, 0, usb2),
+	TEGRA186_LANE("usb2-1", 0,  0, 0, usb2),
+	TEGRA186_LANE("usb2-2", 0,  0, 0, usb2),
+};
+
+static const struct tegra_xusb_pad_soc tegra186_usb2_pad = {
+	.name = "usb2",
+	.num_lanes = ARRAY_SIZE(tegra186_usb2_lanes),
+	.lanes = tegra186_usb2_lanes,
+	.ops = &tegra186_usb2_pad_ops,
+};
+
+static int tegra186_usb2_port_enable(struct tegra_xusb_port *port)
+{
+	return 0;
+}
+
+static void tegra186_usb2_port_disable(struct tegra_xusb_port *port)
+{
+}
+
+static struct tegra_xusb_lane *
+tegra186_usb2_port_map(struct tegra_xusb_port *port)
+{
+	return tegra_xusb_find_lane(port->padctl, "usb2", port->index);
+}
+
+static const struct tegra_xusb_port_ops tegra186_usb2_port_ops = {
+	.enable = tegra186_usb2_port_enable,
+	.disable = tegra186_usb2_port_disable,
+	.map = tegra186_usb2_port_map,
+};
+
+/* SuperSpeed PHY support */
+static struct tegra_xusb_lane *
+tegra186_usb3_lane_probe(struct tegra_xusb_pad *pad, struct device_node *np,
+			 unsigned int index)
+{
+	struct tegra_xusb_usb3_lane *usb3;
+	int err;
+
+	usb3 = kzalloc(sizeof(*usb3), GFP_KERNEL);
+	if (!usb3)
+		return ERR_PTR(-ENOMEM);
+
+	INIT_LIST_HEAD(&usb3->base.list);
+	usb3->base.soc = &pad->soc->lanes[index];
+	usb3->base.index = index;
+	usb3->base.pad = pad;
+	usb3->base.np = np;
+
+	err = tegra_xusb_lane_parse_dt(&usb3->base, np);
+	if (err < 0) {
+		kfree(usb3);
+		return ERR_PTR(err);
+	}
+
+	return &usb3->base;
+}
+
+static void tegra186_usb3_lane_remove(struct tegra_xusb_lane *lane)
+{
+	struct tegra_xusb_usb3_lane *usb3 = to_usb3_lane(lane);
+
+	kfree(usb3);
+}
+
+static const struct tegra_xusb_lane_ops tegra186_usb3_lane_ops = {
+	.probe = tegra186_usb3_lane_probe,
+	.remove = tegra186_usb3_lane_remove,
+};
+static int tegra186_usb3_port_enable(struct tegra_xusb_port *port)
+{
+	return 0;
+}
+
+static void tegra186_usb3_port_disable(struct tegra_xusb_port *port)
+{
+}
+
+static struct tegra_xusb_lane *
+tegra186_usb3_port_map(struct tegra_xusb_port *port)
+{
+	return tegra_xusb_find_lane(port->padctl, "usb3", port->index);
+}
+
+static const struct tegra_xusb_port_ops tegra186_usb3_port_ops = {
+	.enable = tegra186_usb3_port_enable,
+	.disable = tegra186_usb3_port_disable,
+	.map = tegra186_usb3_port_map,
+};
+
+static int tegra186_usb3_phy_power_on(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	struct tegra_xusb_usb3_port *port;
+	struct tegra_xusb_usb2_port *usb2;
+	unsigned int index = lane->index;
+	struct device *dev = padctl->dev;
+	u32 value;
+
+	port = tegra_xusb_find_usb3_port(padctl, index);
+	if (!port) {
+		dev_err(dev, "no port found for USB3 lane %u\n", index);
+		return -ENODEV;
+	}
+
+	usb2 = tegra_xusb_find_usb2_port(padctl, port->port);
+	if (!usb2) {
+		dev_err(dev, "no companion port found for USB3 lane %u\n",
+			index);
+		return -ENODEV;
+	}
+
+	mutex_lock(&padctl->lock);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_SS_PORT_CAP);
+	value &= ~(PORT_CAP_MASK << PORTX_CAP_SHIFT(index));
+
+	if (usb2->mode == USB_DR_MODE_UNKNOWN)
+		value |= (PORT_CAP_DISABLED << PORTX_CAP_SHIFT(index));
+	else if (usb2->mode == USB_DR_MODE_PERIPHERAL)
+		value |= (PORT_CAP_DEVICE << PORTX_CAP_SHIFT(index));
+	else if (usb2->mode == USB_DR_MODE_HOST)
+		value |= (PORT_CAP_HOST << PORTX_CAP_SHIFT(index));
+	else if (usb2->mode == USB_DR_MODE_OTG)
+		value |= (PORT_CAP_OTG << PORTX_CAP_SHIFT(index));
+
+	padctl_writel(padctl, value, XUSB_PADCTL_SS_PORT_CAP);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
+	value &= ~SSPX_ELPG_VCORE_DOWN(index);
+	padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
+
+	usleep_range(100, 200);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
+	value &= ~SSPX_ELPG_CLAMP_EN_EARLY(index);
+	padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
+
+	usleep_range(100, 200);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
+	value &= ~SSPX_ELPG_CLAMP_EN(index);
+	padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
+
+	mutex_unlock(&padctl->lock);
+
+	return 0;
+}
+
+static int tegra186_usb3_phy_power_off(struct phy *phy)
+{
+	struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+	struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+	struct tegra_xusb_usb3_port *port;
+	unsigned int index = lane->index;
+	struct device *dev = padctl->dev;
+	u32 value;
+
+	port = tegra_xusb_find_usb3_port(padctl, index);
+	if (!port) {
+		dev_err(dev, "no port found for USB3 lane %u\n", index);
+		return -ENODEV;
+	}
+
+	mutex_lock(&padctl->lock);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
+	value |= SSPX_ELPG_CLAMP_EN_EARLY(index);
+	padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
+
+	usleep_range(100, 200);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
+	value |= SSPX_ELPG_CLAMP_EN(index);
+	padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
+
+	usleep_range(250, 350);
+
+	value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
+	value |= SSPX_ELPG_VCORE_DOWN(index);
+	padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
+
+	mutex_unlock(&padctl->lock);
+
+	return 0;
+}
+
+static int tegra186_usb3_phy_init(struct phy *phy)
+{
+	return 0;
+}
+
+static int tegra186_usb3_phy_exit(struct phy *phy)
+{
+	return 0;
+}
+
+static const struct phy_ops usb3_phy_ops = {
+	.init = tegra186_usb3_phy_init,
+	.exit = tegra186_usb3_phy_exit,
+	.power_on = tegra186_usb3_phy_power_on,
+	.power_off = tegra186_usb3_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static struct tegra_xusb_pad *
+tegra186_usb3_pad_probe(struct tegra_xusb_padctl *padctl,
+			const struct tegra_xusb_pad_soc *soc,
+			struct device_node *np)
+{
+	struct tegra_xusb_usb3_pad *usb3;
+	struct tegra_xusb_pad *pad;
+	int err;
+
+	usb3 = kzalloc(sizeof(*usb3), GFP_KERNEL);
+	if (!usb3)
+		return ERR_PTR(-ENOMEM);
+
+	pad = &usb3->base;
+	pad->ops = &tegra186_usb3_lane_ops;
+	pad->soc = soc;
+
+	err = tegra_xusb_pad_init(pad, padctl, np);
+	if (err < 0) {
+		kfree(usb3);
+		goto out;
+	}
+
+	err = tegra_xusb_pad_register(pad, &usb3_phy_ops);
+	if (err < 0)
+		goto unregister;
+
+	dev_set_drvdata(&pad->dev, pad);
+
+	return pad;
+
+unregister:
+	device_unregister(&pad->dev);
+out:
+	return ERR_PTR(err);
+}
+
+static void tegra186_usb3_pad_remove(struct tegra_xusb_pad *pad)
+{
+	struct tegra_xusb_usb2_pad *usb2 = to_usb2_pad(pad);
+
+	kfree(usb2);
+}
+
+static const struct tegra_xusb_pad_ops tegra186_usb3_pad_ops = {
+	.probe = tegra186_usb3_pad_probe,
+	.remove = tegra186_usb3_pad_remove,
+};
+
+static const char * const tegra186_usb3_functions[] = {
+	"xusb",
+};
+
+static const struct tegra_xusb_lane_soc tegra186_usb3_lanes[] = {
+	TEGRA186_LANE("usb3-0", 0,  0, 0, usb3),
+	TEGRA186_LANE("usb3-1", 0,  0, 0, usb3),
+	TEGRA186_LANE("usb3-2", 0,  0, 0, usb3),
+};
+
+static const struct tegra_xusb_pad_soc tegra186_usb3_pad = {
+	.name = "usb3",
+	.num_lanes = ARRAY_SIZE(tegra186_usb3_lanes),
+	.lanes = tegra186_usb3_lanes,
+	.ops = &tegra186_usb3_pad_ops,
+};
+
+static const struct tegra_xusb_pad_soc * const tegra186_pads[] = {
+	&tegra186_usb2_pad,
+	&tegra186_usb3_pad,
+#if 0 /* TODO implement */
+	&tegra186_hsic_pad,
+#endif
+};
+
+static int
+tegra186_xusb_read_fuse_calibration(struct tegra186_xusb_padctl *padctl)
+{
+	struct device *dev = padctl->base.dev;
+	unsigned int i, count;
+	u32 value, *level;
+	int err;
+
+	count = padctl->base.soc->ports.usb2.count;
+
+	level = devm_kcalloc(dev, count, sizeof(u32), GFP_KERNEL);
+	if (!level)
+		return -ENOMEM;
+
+	err = tegra_fuse_readl(TEGRA_FUSE_SKU_CALIB_0, &value);
+	if (err) {
+		dev_err(dev, "failed to read calibration fuse: %d\n", err);
+		return err;
+	}
+
+	dev_dbg(dev, "FUSE_USB_CALIB_0 %#x\n", value);
+
+	for (i = 0; i < count; i++)
+		level[i] = (value >> HS_CURR_LEVEL_PADX_SHIFT(i)) &
+				HS_CURR_LEVEL_PAD_MASK;
+
+	padctl->calib.hs_curr_level = level;
+
+	padctl->calib.hs_squelch = (value >> HS_SQUELCH_SHIFT) &
+					HS_SQUELCH_MASK;
+	padctl->calib.hs_term_range_adj = (value >> HS_TERM_RANGE_ADJ_SHIFT) &
+						HS_TERM_RANGE_ADJ_MASK;
+
+	err = tegra_fuse_readl(TEGRA_FUSE_USB_CALIB_EXT_0, &value);
+	if (err) {
+		dev_err(dev, "failed to read calibration fuse: %d\n", err);
+		return err;
+	}
+
+	dev_dbg(dev, "FUSE_USB_CALIB_EXT_0 %#x\n", value);
+
+	padctl->calib.rpd_ctrl = (value >> RPD_CTRL_SHIFT) & RPD_CTRL_MASK;
+
+	return 0;
+}
+
+static struct tegra_xusb_padctl *
+tegra186_xusb_padctl_probe(struct device *dev,
+			   const struct tegra_xusb_padctl_soc *soc)
+{
+	struct tegra186_xusb_padctl *priv;
+	int err;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return ERR_PTR(-ENOMEM);
+
+	priv->base.dev = dev;
+	priv->base.soc = soc;
+
+	err = tegra186_xusb_read_fuse_calibration(priv);
+	if (err < 0)
+		return ERR_PTR(err);
+
+	return &priv->base;
+}
+
+static void tegra186_xusb_padctl_remove(struct tegra_xusb_padctl *padctl)
+{
+}
+
+static const struct tegra_xusb_padctl_ops tegra186_xusb_padctl_ops = {
+	.probe = tegra186_xusb_padctl_probe,
+	.remove = tegra186_xusb_padctl_remove,
+};
+
+static const char * const tegra186_xusb_padctl_supply_names[] = {
+	"avdd-pll-erefeut",
+	"avdd-usb",
+	"vclamp-usb",
+	"vddio-hsic",
+};
+
+const struct tegra_xusb_padctl_soc tegra186_xusb_padctl_soc = {
+	.num_pads = ARRAY_SIZE(tegra186_pads),
+	.pads = tegra186_pads,
+	.ports = {
+		.usb2 = {
+			.ops = &tegra186_usb2_port_ops,
+			.count = 3,
+		},
+#if 0 /* TODO implement */
+		.hsic = {
+			.ops = &tegra186_hsic_port_ops,
+			.count = 1,
+		},
+#endif
+		.usb3 = {
+			.ops = &tegra186_usb3_port_ops,
+			.count = 3,
+		},
+	},
+	.ops = &tegra186_xusb_padctl_ops,
+	.supply_names = tegra186_xusb_padctl_supply_names,
+	.num_supplies = ARRAY_SIZE(tegra186_xusb_padctl_supply_names),
+};
+EXPORT_SYMBOL_GPL(tegra186_xusb_padctl_soc);
+
+MODULE_AUTHOR("JC Kuo <jckuo@nvidia.com>");
+MODULE_DESCRIPTION("NVIDIA Tegra186 XUSB Pad Controller driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/tegra/xusb.c b/drivers/phy/tegra/xusb.c
index e510629f4f1c..0417213ed68b 100644
--- a/drivers/phy/tegra/xusb.c
+++ b/drivers/phy/tegra/xusb.c
@@ -67,6 +67,12 @@ static const struct of_device_id tegra_xusb_padctl_of_match[] = {
 		.compatible = "nvidia,tegra210-xusb-padctl",
 		.data = &tegra210_xusb_padctl_soc,
 	},
+#endif
+#if defined(CONFIG_ARCH_TEGRA_186_SOC)
+	{
+		.compatible = "nvidia,tegra186-xusb-padctl",
+		.data = &tegra186_xusb_padctl_soc,
+	},
 #endif
 	{ }
 };
diff --git a/drivers/phy/tegra/xusb.h b/drivers/phy/tegra/xusb.h
index 5d5d22f6cb41..e0028b9fe702 100644
--- a/drivers/phy/tegra/xusb.h
+++ b/drivers/phy/tegra/xusb.h
@@ -56,10 +56,21 @@ struct tegra_xusb_lane {
 int tegra_xusb_lane_parse_dt(struct tegra_xusb_lane *lane,
 			     struct device_node *np);
 
+struct tegra_xusb_usb3_lane {
+	struct tegra_xusb_lane base;
+};
+
+static inline struct tegra_xusb_usb3_lane *
+to_usb3_lane(struct tegra_xusb_lane *lane)
+{
+	return container_of(lane, struct tegra_xusb_usb3_lane, base);
+}
+
 struct tegra_xusb_usb2_lane {
 	struct tegra_xusb_lane base;
 
 	u32 hs_curr_level_offset;
+	bool powered_on;
 };
 
 static inline struct tegra_xusb_usb2_lane *
@@ -170,6 +181,19 @@ int tegra_xusb_pad_register(struct tegra_xusb_pad *pad,
 			    const struct phy_ops *ops);
 void tegra_xusb_pad_unregister(struct tegra_xusb_pad *pad);
 
+struct tegra_xusb_usb3_pad {
+	struct tegra_xusb_pad base;
+
+	unsigned int enable;
+	struct mutex lock;
+};
+
+static inline struct tegra_xusb_usb3_pad *
+to_usb3_pad(struct tegra_xusb_pad *pad)
+{
+	return container_of(pad, struct tegra_xusb_usb3_pad, base);
+}
+
 struct tegra_xusb_usb2_pad {
 	struct tegra_xusb_pad base;
 
@@ -425,5 +449,8 @@ extern const struct tegra_xusb_padctl_soc tegra124_xusb_padctl_soc;
 #if defined(CONFIG_ARCH_TEGRA_210_SOC)
 extern const struct tegra_xusb_padctl_soc tegra210_xusb_padctl_soc;
 #endif
+#if defined(CONFIG_ARCH_TEGRA_186_SOC)
+extern const struct tegra_xusb_padctl_soc tegra186_xusb_padctl_soc;
+#endif
 
 #endif /* __PHY_TEGRA_XUSB_H */
-- 
2.20.1

Re: [PATCH v2 1/5] dt-bindings: phy: tegra: Add Tegra186 support

[Rob Herring]

On Thu, 21 Feb 2019 16:46:30 +0100, Thierry Reding wrote:
> From: Thierry Reding <treding@nvidia.com>
> 
> Extend the bindings to cover the set of features found in Tegra186. Note
> that, technically, there are four more supplies connected to the XUSB
> pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL), but
> the power sequencing requirements of Tegra186 require these to be under
> the control of the PMIC.
> 
> Reviewed-by: JC Kuo <jckuo@nvidia.com>
> Signed-off-by: Thierry Reding <treding@nvidia.com>
> ---
>  .../bindings/phy/nvidia,tegra124-xusb-padctl.txt         | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v2 0/5] phy: tegra: xusb: Add Tegra186 support

[Kishon Vijay Abraham I]

Hi Thierry,

On 21/02/19 9:16 PM, Thierry Reding wrote:
> From: Thierry Reding <treding@nvidia.com>
> 
> This series adds support for Tegra186 to the XUSB pad controller driver.
> Patch 1 extends the device tree bindings with support for Tegra186 while
> patches 2-4 are preparatory work for the final patch 5 that adds the
> Tegra186 specific programming for the UPHY blocks.
> 
> Changes in v2:
> - address review comments from Kishon
> - added Reviewed-by tags from JC

I've merged this series.
However I'd like to see if we can add the features of xusb.c to phy-core.c and
remove xusb.c. This will be useful if there are other PHY vendors with similar
design as Tegra.

Thanks
Kishon

> 
> Thierry
> 
> JC Kuo (2):
>   phy: tegra: xusb: Skip single function lane programming
>   phy: tegra: xusb: Add Tegra186 support
> 
> Thierry Reding (3):
>   dt-bindings: phy: tegra: Add Tegra186 support
>   phy: tegra: xusb: Parse dual-role mode property
>   phy: tegra: xusb: Add support for power supplies
> 
>  .../phy/nvidia,tegra124-xusb-padctl.txt       |   9 +
>  MAINTAINERS                                   |   5 +
>  drivers/phy/tegra/Makefile                    |   1 +
>  drivers/phy/tegra/xusb-tegra186.c             | 899 ++++++++++++++++++
>  drivers/phy/tegra/xusb.c                      |  67 +-
>  drivers/phy/tegra/xusb.h                      |  35 +
>  6 files changed, 1014 insertions(+), 2 deletions(-)
>  create mode 100644 drivers/phy/tegra/xusb-tegra186.c
>