From: Jonathan Cameron <jic23@kernel.org>
To: Stefan Popa <stefan.popa@analog.com>
Cc: <robh+dt@kernel.org>, <Michael.Hennerich@analog.com>,
<knaack.h@gmx.de>, <lars@metafoo.de>, <pmeerw@pmeerw.net>,
<gregkh@linuxfoundation.org>, <linux-kernel@vger.kernel.org>,
<linux-iio@vger.kernel.org>, <devicetree@vger.kernel.org>
Subject: Re: [PATCH v3 7/7] iio: imu: adis16480: Add docs for ADIS16480 IMU
Date: Sun, 3 Mar 2019 12:54:29 +0000 [thread overview]
Message-ID: <20190303125429.3f2c7d70@archlinux> (raw)
In-Reply-To: <1551284068-4882-8-git-send-email-stefan.popa@analog.com>
On Wed, 27 Feb 2019 18:14:28 +0200
Stefan Popa <stefan.popa@analog.com> wrote:
> Document support for ADIS16480 Inertial Measurement Unit.
>
> Signed-off-by: Stefan Popa <stefan.popa@analog.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
Applied.
Thanks,
Jonathan
> ---
> .../devicetree/bindings/iio/imu/adi,adis16480.txt | 49 ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 50 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt
> new file mode 100644
> index 0000000..39ab016
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16480.txt
> @@ -0,0 +1,49 @@
> +
> +Analog Devices ADIS16480 and similar IMUs
> +
> +Required properties for the ADIS16480:
> +
> +- compatible: Must be one of
> + * "adi,adis16375"
> + * "adi,adis16480"
> + * "adi,adis16485"
> + * "adi,adis16488"
> + * "adi,adis16495-1"
> + * "adi,adis16495-2"
> + * "adi,adis16495-3"
> + * "adi,adis16497-1"
> + * "adi,adis16497-2"
> + * "adi,adis16497-3"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpol: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- interrupts: interrupt mapping for IRQ, accepted values are:
> + * IRQF_TRIGGER_RISING
> + * IRQF_TRIGGER_FALLING
> +
> +Optional properties:
> +
> +- interrupt-names: Data ready line selection. Valid values are:
> + * DIO1
> + * DIO2
> + * DIO3
> + * DIO4
> + If this field is left empty, DIO1 is assigned as default data ready
> + signal.
> +- reset-gpios: must be the device tree identifier of the RESET pin. As the line
> + is active low, it should be marked GPIO_ACTIVE_LOW.
> +
> +Example:
> +
> + imu@0 {
> + compatible = "adi,adis16495-1";
> + reg = <0>;
> + spi-max-frequency = <3200000>;
> + spi-cpol;
> + spi-cpha;
> + interrupts = <25 IRQF_TRIGGER_FALLING>;
> + interrupt-parent = <&gpio>;
> + interrupt-names = "DIO2";
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index e4091ac..beecd1e 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -942,6 +942,7 @@ F: drivers/dma/dma-axi-dmac.c
> ANALOG DEVICES INC IIO DRIVERS
> M: Lars-Peter Clausen <lars@metafoo.de>
> M: Michael Hennerich <Michael.Hennerich@analog.com>
> +M: Stefan Popa <stefan.popa@analog.com>
> W: http://wiki.analog.com/
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
prev parent reply other threads:[~2019-03-03 12:54 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-27 16:14 [PATCH v3 0/7] iio: imu: adis16480: Add support for ADIS1649x family of devices Stefan Popa
2019-02-27 16:14 ` [PATCH v3 1/7] iio: imu: adis16480: Add support for configurable drdy indicator Stefan Popa
2019-03-03 12:46 ` Jonathan Cameron
2019-02-27 16:14 ` [PATCH v3 2/7] iio: imu: adis16480: Add OF device ID table Stefan Popa
2019-03-03 12:46 ` Jonathan Cameron
2019-02-27 16:14 ` [PATCH v3 3/7] iio: imu: adis16480: Treat temperature scale in a generic way Stefan Popa
2019-03-03 12:47 ` Jonathan Cameron
2019-02-27 16:14 ` [PATCH v3 4/7] iio: imu: adis16480: Calculate the sampling frequency " Stefan Popa
2019-03-03 12:51 ` Jonathan Cameron
2019-02-27 16:14 ` [PATCH v3 5/7] iio: imu: adis16480: Deal with filter freq " Stefan Popa
2019-03-03 12:52 ` Jonathan Cameron
2019-02-27 16:14 ` [PATCH v3 6/7] iio: imu: adis16480: Add support for ADIS1649x family of devices Stefan Popa
2019-03-03 12:53 ` Jonathan Cameron
2019-02-27 16:14 ` [PATCH v3 7/7] iio: imu: adis16480: Add docs for ADIS16480 IMU Stefan Popa
2019-03-03 12:54 ` Jonathan Cameron [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190303125429.3f2c7d70@archlinux \
--to=jic23@kernel.org \
--cc=Michael.Hennerich@analog.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=pmeerw@pmeerw.net \
--cc=robh+dt@kernel.org \
--cc=stefan.popa@analog.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).