[PATCH AUTOSEL 4.9 01/29] ARM: dts: bcm283x: Fix hdmi hpd gpio pull

[PATCH AUTOSEL 4.9 01/29] ARM: dts: bcm283x: Fix hdmi hpd gpio pull

[Sasha Levin]

From: Helen Koike <helen.koike@collabora.com>

[ Upstream commit 544e784188f1dd7c797c70b213385e67d92005b6 ]

Raspberry pi board model B revison 2 have the hot plug detector gpio
active high (and not low as it was in the dts).

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Fixes: 49ac67e0c39c ("ARM: bcm2835: Add VC4 to the device tree.")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 84df85ea6296..7efde03daadd 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -26,5 +26,5 @@
 };
 
 &hdmi {
-	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
-- 
2.19.1

[PATCH AUTOSEL 4.9 02/29] s390: limit brk randomization to 32MB

[Sasha Levin]

From: Martin Schwidefsky <schwidefsky@de.ibm.com>

[ Upstream commit cd479eccd2e057116d504852814402a1e68ead80 ]

For a 64-bit process the randomization of the program break is quite
large with 1GB. That is as big as the randomization of the anonymous
mapping base, for a test case started with '/lib/ld64.so.1 <exec>'
it can happen that the heap is placed after the stack. To avoid
this limit the program break randomization to 32MB for 64-bit and
keep 8MB for 31-bit.

Reported-by: Stefan Liebler <stli@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/s390/include/asm/elf.h | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/arch/s390/include/asm/elf.h b/arch/s390/include/asm/elf.h
index 8d665f1b29f8..f0fe566a9910 100644
--- a/arch/s390/include/asm/elf.h
+++ b/arch/s390/include/asm/elf.h
@@ -215,11 +215,14 @@ do {								\
 
 /*
  * Cache aliasing on the latest machines calls for a mapping granularity
- * of 512KB. For 64-bit processes use a 512KB alignment and a randomization
- * of up to 1GB. For 31-bit processes the virtual address space is limited,
- * use no alignment and limit the randomization to 8MB.
+ * of 512KB for the anonymous mapping base. For 64-bit processes use a
+ * 512KB alignment and a randomization of up to 1GB. For 31-bit processes
+ * the virtual address space is limited, use no alignment and limit the
+ * randomization to 8MB.
+ * For the additional randomization of the program break use 32MB for
+ * 64-bit and 8MB for 31-bit.
  */
-#define BRK_RND_MASK	(is_compat_task() ? 0x7ffUL : 0x3ffffUL)
+#define BRK_RND_MASK	(is_compat_task() ? 0x7ffUL : 0x1fffUL)
 #define MMAP_RND_MASK	(is_compat_task() ? 0x7ffUL : 0x3ff80UL)
 #define MMAP_ALIGN_MASK	(is_compat_task() ? 0 : 0x7fUL)
 #define STACK_RND_MASK	MMAP_RND_MASK
-- 
2.19.1

[PATCH AUTOSEL 4.9 03/29] qlcnic: Avoid potential NULL pointer dereference

[Sasha Levin]

From: Aditya Pakki <pakki001@umn.edu>

[ Upstream commit 5bf7295fe34a5251b1d241b9736af4697b590670 ]

netdev_alloc_skb can fail and return a NULL pointer which is
dereferenced without a check. The patch avoids such a scenario.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
index 0a2318cad34d..63ebc491057b 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
@@ -1038,6 +1038,8 @@ int qlcnic_do_lb_test(struct qlcnic_adapter *adapter, u8 mode)
 
 	for (i = 0; i < QLCNIC_NUM_ILB_PKT; i++) {
 		skb = netdev_alloc_skb(adapter->netdev, QLCNIC_ILB_PKT_SIZE);
+		if (!skb)
+			break;
 		qlcnic_create_loopback_buff(skb->data, adapter->mac_addr);
 		skb_put(skb, QLCNIC_ILB_PKT_SIZE);
 		adapter->ahw->diag_cnt = 0;
-- 
2.19.1

[PATCH AUTOSEL 4.9 04/29] netfilter: nft_set_rbtree: check for inactive element after flag mismatch

[Sasha Levin]

From: Pablo Neira Ayuso <pablo@netfilter.org>

[ Upstream commit 05b7639da55f5555b9866a1f4b7e8995232a6323 ]

Otherwise, we hit bogus ENOENT when removing elements.

Fixes: e701001e7cbe ("netfilter: nft_rbtree: allow adjacent intervals with dynamic updates")
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/netfilter/nft_set_rbtree.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/net/netfilter/nft_set_rbtree.c b/net/netfilter/nft_set_rbtree.c
index 93820e0d8814..4ee8acded0a4 100644
--- a/net/netfilter/nft_set_rbtree.c
+++ b/net/netfilter/nft_set_rbtree.c
@@ -191,10 +191,6 @@ static void *nft_rbtree_deactivate(const struct net *net,
 		else if (d > 0)
 			parent = parent->rb_right;
 		else {
-			if (!nft_set_elem_active(&rbe->ext, genmask)) {
-				parent = parent->rb_left;
-				continue;
-			}
 			if (nft_rbtree_interval_end(rbe) &&
 			    !nft_rbtree_interval_end(this)) {
 				parent = parent->rb_left;
@@ -203,6 +199,9 @@ static void *nft_rbtree_deactivate(const struct net *net,
 				   nft_rbtree_interval_end(this)) {
 				parent = parent->rb_right;
 				continue;
+			} else if (!nft_set_elem_active(&rbe->ext, genmask)) {
+				parent = parent->rb_left;
+				continue;
 			}
 			nft_set_elem_change_active(net, set, &rbe->ext);
 			return rbe;
-- 
2.19.1

[PATCH AUTOSEL 4.9 05/29] netfilter: bridge: set skb transport_header before entering NF_INET_PRE_ROUTING

[Sasha Levin]

From: Xin Long <lucien.xin@gmail.com>

[ Upstream commit e166e4fdaced850bee3d5ee12a5740258fb30587 ]

Since Commit 21d1196a35f5 ("ipv4: set transport header earlier"),
skb->transport_header has been always set before entering INET
netfilter. This patch is to set skb->transport_header for bridge
before entering INET netfilter by bridge-nf-call-iptables.

It also fixes an issue that sctp_error() couldn't compute a right
csum due to unset skb->transport_header.

Fixes: e6d8b64b34aa ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 net/bridge/br_netfilter_hooks.c | 1 +
 net/bridge/br_netfilter_ipv6.c  | 2 ++
 2 files changed, 3 insertions(+)

diff --git a/net/bridge/br_netfilter_hooks.c b/net/bridge/br_netfilter_hooks.c
index 38865deab3ac..0c96773d1829 100644
--- a/net/bridge/br_netfilter_hooks.c
+++ b/net/bridge/br_netfilter_hooks.c
@@ -512,6 +512,7 @@ static unsigned int br_nf_pre_routing(void *priv,
 	nf_bridge->ipv4_daddr = ip_hdr(skb)->daddr;
 
 	skb->protocol = htons(ETH_P_IP);
+	skb->transport_header = skb->network_header + ip_hdr(skb)->ihl * 4;
 
 	NF_HOOK(NFPROTO_IPV4, NF_INET_PRE_ROUTING, state->net, state->sk, skb,
 		skb->dev, NULL,
diff --git a/net/bridge/br_netfilter_ipv6.c b/net/bridge/br_netfilter_ipv6.c
index a1b57cb07f1e..8c08dd07419f 100644
--- a/net/bridge/br_netfilter_ipv6.c
+++ b/net/bridge/br_netfilter_ipv6.c
@@ -235,6 +235,8 @@ unsigned int br_nf_pre_routing_ipv6(void *priv,
 	nf_bridge->ipv6_daddr = ipv6_hdr(skb)->daddr;
 
 	skb->protocol = htons(ETH_P_IPV6);
+	skb->transport_header = skb->network_header + sizeof(struct ipv6hdr);
+
 	NF_HOOK(NFPROTO_IPV6, NF_INET_PRE_ROUTING, state->net, state->sk, skb,
 		skb->dev, NULL,
 		br_nf_pre_routing_finish_ipv6);
-- 
2.19.1

[PATCH AUTOSEL 4.9 06/29] sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()

[Sasha Levin]

From: Mao Wenan <maowenan@huawei.com>

[ Upstream commit ac0cdb3d990108df795b676cd0d0e65ac34b2273 ]

Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.

Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/tty/serial/sc16is7xx.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index ea6b62cece88..82451bb6622b 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1482,7 +1482,7 @@ static int __init sc16is7xx_init(void)
 	ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver);
 	if (ret < 0) {
 		pr_err("failed to init sc16is7xx i2c --> %d\n", ret);
-		return ret;
+		goto err_i2c;
 	}
 #endif
 
@@ -1490,10 +1490,18 @@ static int __init sc16is7xx_init(void)
 	ret = spi_register_driver(&sc16is7xx_spi_uart_driver);
 	if (ret < 0) {
 		pr_err("failed to init sc16is7xx spi --> %d\n", ret);
-		return ret;
+		goto err_spi;
 	}
 #endif
 	return ret;
+
+err_spi:
+#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
+	i2c_del_driver(&sc16is7xx_i2c_uart_driver);
+#endif
+err_i2c:
+	uart_unregister_driver(&sc16is7xx_uart);
+	return ret;
 }
 module_init(sc16is7xx_init);
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 07/29] serial: ar933x_uart: Fix build failure with disabled console

[Sasha Levin]

From: Petr Štetiar <ynezz@true.cz>

[ Upstream commit 72ff51d8dd262d1fef25baedc2ac35116435be47 ]

Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:

 ar933x_uart.c: In function 'ar933x_uart_console_write':
 ar933x_uart.c:550:14: error: 'struct uart_port' has no
                               member named 'sysrq'

So this patch moves all the code related to console handling behind
series of CONFIG_SERIAL_AR933X_CONSOLE ifdefs.

1. https://bugs.openwrt.org/index.php?do=details&task_id=2152

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrey Batyiev <batyiev@gmail.com>
Reported-by: Andrey Batyiev <batyiev@gmail.com>
Tested-by: Andrey Batyiev <batyiev@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/tty/serial/ar933x_uart.c | 24 ++++++++----------------
 1 file changed, 8 insertions(+), 16 deletions(-)

diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index 73137f4aac20..d4462512605b 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -52,11 +52,6 @@ struct ar933x_uart_port {
 	struct clk		*clk;
 };
 
-static inline bool ar933x_uart_console_enabled(void)
-{
-	return IS_ENABLED(CONFIG_SERIAL_AR933X_CONSOLE);
-}
-
 static inline unsigned int ar933x_uart_read(struct ar933x_uart_port *up,
 					    int offset)
 {
@@ -511,6 +506,7 @@ static struct uart_ops ar933x_uart_ops = {
 	.verify_port	= ar933x_uart_verify_port,
 };
 
+#ifdef CONFIG_SERIAL_AR933X_CONSOLE
 static struct ar933x_uart_port *
 ar933x_console_ports[CONFIG_SERIAL_AR933X_NR_UARTS];
 
@@ -607,14 +603,7 @@ static struct console ar933x_uart_console = {
 	.index		= -1,
 	.data		= &ar933x_uart_driver,
 };
-
-static void ar933x_uart_add_console_port(struct ar933x_uart_port *up)
-{
-	if (!ar933x_uart_console_enabled())
-		return;
-
-	ar933x_console_ports[up->port.line] = up;
-}
+#endif /* CONFIG_SERIAL_AR933X_CONSOLE */
 
 static struct uart_driver ar933x_uart_driver = {
 	.owner		= THIS_MODULE,
@@ -703,7 +692,9 @@ static int ar933x_uart_probe(struct platform_device *pdev)
 	baud = ar933x_uart_get_baud(port->uartclk, 0, AR933X_UART_MAX_STEP);
 	up->max_baud = min_t(unsigned int, baud, AR933X_UART_MAX_BAUD);
 
-	ar933x_uart_add_console_port(up);
+#ifdef CONFIG_SERIAL_AR933X_CONSOLE
+	ar933x_console_ports[up->port.line] = up;
+#endif
 
 	ret = uart_add_one_port(&ar933x_uart_driver, &up->port);
 	if (ret)
@@ -752,8 +743,9 @@ static int __init ar933x_uart_init(void)
 {
 	int ret;
 
-	if (ar933x_uart_console_enabled())
-		ar933x_uart_driver.cons = &ar933x_uart_console;
+#ifdef CONFIG_SERIAL_AR933X_CONSOLE
+	ar933x_uart_driver.cons = &ar933x_uart_console;
+#endif
 
 	ret = uart_register_driver(&ar933x_uart_driver);
 	if (ret)
-- 
2.19.1

[PATCH AUTOSEL 4.9 08/29] usb: gadget: net2280: Fix overrun of OUT messages

[Sasha Levin]

From: Guido Kiener <guido@kiener-muenchen.de>

[ Upstream commit 9d6a54c1430647355a5e23434881b2ca3d192b48 ]

The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.

The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.

With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met.  This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/gadget/udc/net2280.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index 7a8c36642293..57b88f4f49c5 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -870,9 +870,6 @@ static void start_queue(struct net2280_ep *ep, u32 dmactl, u32 td_dma)
 	(void) readl(&ep->dev->pci->pcimstctl);
 
 	writel(BIT(DMA_START), &dma->dmastat);
-
-	if (!ep->is_in)
-		stop_out_naking(ep);
 }
 
 static void start_dma(struct net2280_ep *ep, struct net2280_request *req)
@@ -911,6 +908,7 @@ static void start_dma(struct net2280_ep *ep, struct net2280_request *req)
 			writel(BIT(DMA_START), &dma->dmastat);
 			return;
 		}
+		stop_out_naking(ep);
 	}
 
 	tmp = dmactl_default;
-- 
2.19.1

[PATCH AUTOSEL 4.9 09/29] usb: gadget: net2280: Fix net2280_dequeue()

[Sasha Levin]

From: Guido Kiener <guido@kiener-muenchen.de>

[ Upstream commit f1d3fba17cd4eeea20397f1324b7b9c69a6a935c ]

When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/gadget/udc/net2280.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/gadget/udc/net2280.c b/drivers/usb/gadget/udc/net2280.c
index 57b88f4f49c5..dfaed8e8cc52 100644
--- a/drivers/usb/gadget/udc/net2280.c
+++ b/drivers/usb/gadget/udc/net2280.c
@@ -1277,9 +1277,9 @@ static int net2280_dequeue(struct usb_ep *_ep, struct usb_request *_req)
 			break;
 	}
 	if (&req->req != _req) {
+		ep->stopped = stopped;
 		spin_unlock_irqrestore(&ep->dev->lock, flags);
-		dev_err(&ep->dev->pdev->dev, "%s: Request mismatch\n",
-								__func__);
+		ep_dbg(ep->dev, "%s: Request mismatch\n", __func__);
 		return -EINVAL;
 	}
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 10/29] usb: gadget: net2272: Fix net2272_dequeue()

[Sasha Levin]

From: Guido Kiener <guido@kiener-muenchen.de>

[ Upstream commit 091dacc3cc10979ab0422f0a9f7fcc27eee97e69 ]

Restore the status of ep->stopped in function net2272_dequeue().

When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.

This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/gadget/udc/net2272.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/usb/gadget/udc/net2272.c b/drivers/usb/gadget/udc/net2272.c
index 40396a265a3f..f57d293a1791 100644
--- a/drivers/usb/gadget/udc/net2272.c
+++ b/drivers/usb/gadget/udc/net2272.c
@@ -958,6 +958,7 @@ net2272_dequeue(struct usb_ep *_ep, struct usb_request *_req)
 			break;
 	}
 	if (&req->req != _req) {
+		ep->stopped = stopped;
 		spin_unlock_irqrestore(&ep->dev->lock, flags);
 		return -EINVAL;
 	}
-- 
2.19.1

[PATCH AUTOSEL 4.9 11/29] ARM: dts: pfla02: increase phy reset duration

[Sasha Levin]

From: Marco Felsch <m.felsch@pengutronix.de>

[ Upstream commit 032f85c9360fb1a08385c584c2c4ed114b33c260 ]

Increase the reset duration to ensure correct phy functionality. The
reset duration is taken from barebox commit 52fdd510de ("ARM: dts:
pfla02: use long enough reset for ethernet phy"):

  Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
  small percentage of modules have 'transmission timeouts' errors like

  barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
  warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
  eth0: 1000Mbps full duplex link detected
  eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout
  T eth0: transmission timeout

Cc: Stefan Christ <s.christ@phytec.de>
Cc: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 3180f956668e ("ARM: dts: Phytec imx6q pfla02 and pbab01 support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
index e0280cac2484..fed72a5f3ffa 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -90,6 +90,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	phy-reset-duration = <10>; /* in msecs */
 	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
 	phy-supply = <&vdd_eth_io_reg>;
 	status = "disabled";
-- 
2.19.1

[PATCH AUTOSEL 4.9 12/29] net: ks8851: Dequeue RX packets explicitly

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 536d3680fd2dab5c39857d62a3e084198fc74ff9 ]

The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").

However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management:  On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.

The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.

Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.

The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index 1edc973df4c4..247a3377b951 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -547,9 +547,8 @@ static void ks8851_rx_pkts(struct ks8851_net *ks)
 		/* set dma read address */
 		ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00);
 
-		/* start the packet dma process, and set auto-dequeue rx */
-		ks8851_wrreg16(ks, KS_RXQCR,
-			       ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE);
+		/* start DMA access */
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
 
 		if (rxlen > 4) {
 			unsigned int rxalign;
@@ -580,7 +579,8 @@ static void ks8851_rx_pkts(struct ks8851_net *ks)
 			}
 		}
 
-		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+		/* end DMA access and dequeue packet */
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_RRXEF);
 	}
 }
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 13/29] net: ks8851: Reassert reset pin if chip ID check fails

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 761cfa979a0c177d6c2d93ef5585cd79ae49a7d5 ]

Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.

However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index 247a3377b951..a8c5641ff955 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -1567,9 +1567,9 @@ static int ks8851_probe(struct spi_device *spi)
 	free_irq(ndev->irq, ks);
 
 err_irq:
+err_id:
 	if (gpio_is_valid(gpio))
 		gpio_set_value(gpio, 0);
-err_id:
 	regulator_disable(ks->vdd_reg);
 err_reg:
 	regulator_disable(ks->vdd_io);
-- 
2.19.1

[PATCH AUTOSEL 4.9 14/29] net: ks8851: Delay requesting IRQ until opened

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit d268f31552794abf5b6aa5af31021643411f25f5 ]

The ks8851 driver currently requests the IRQ before registering the
net_device.  Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present.  Most other drivers delay
requesting the IRQ until the net_device is opened.  Do the same.

The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 24 +++++++++++-------------
 1 file changed, 11 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index a8c5641ff955..ff6cab4f6343 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -797,6 +797,15 @@ static void ks8851_tx_work(struct work_struct *work)
 static int ks8851_net_open(struct net_device *dev)
 {
 	struct ks8851_net *ks = netdev_priv(dev);
+	int ret;
+
+	ret = request_threaded_irq(dev->irq, NULL, ks8851_irq,
+				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				   dev->name, ks);
+	if (ret < 0) {
+		netdev_err(dev, "failed to get irq\n");
+		return ret;
+	}
 
 	/* lock the card, even if we may not actually be doing anything
 	 * else at the moment */
@@ -911,6 +920,8 @@ static int ks8851_net_stop(struct net_device *dev)
 		dev_kfree_skb(txb);
 	}
 
+	free_irq(dev->irq, ks);
+
 	return 0;
 }
 
@@ -1542,14 +1553,6 @@ static int ks8851_probe(struct spi_device *spi)
 	ks8851_read_selftest(ks);
 	ks8851_init_mac(ks);
 
-	ret = request_threaded_irq(spi->irq, NULL, ks8851_irq,
-				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				   ndev->name, ks);
-	if (ret < 0) {
-		dev_err(&spi->dev, "failed to get irq\n");
-		goto err_irq;
-	}
-
 	ret = register_netdev(ndev);
 	if (ret) {
 		dev_err(&spi->dev, "failed to register network device\n");
@@ -1562,11 +1565,7 @@ static int ks8851_probe(struct spi_device *spi)
 
 	return 0;
 
-
 err_netdev:
-	free_irq(ndev->irq, ks);
-
-err_irq:
 err_id:
 	if (gpio_is_valid(gpio))
 		gpio_set_value(gpio, 0);
@@ -1587,7 +1586,6 @@ static int ks8851_remove(struct spi_device *spi)
 		dev_info(&spi->dev, "remove\n");
 
 	unregister_netdev(priv->netdev);
-	free_irq(spi->irq, priv);
 	if (gpio_is_valid(priv->gpio))
 		gpio_set_value(priv->gpio, 0);
 	regulator_disable(priv->vdd_reg);
-- 
2.19.1

[PATCH AUTOSEL 4.9 15/29] net: ks8851: Set initial carrier state to down

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit 9624bafa5f6418b9ca5b3f66d1f6a6a2e8bf6d4c ]

The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.

The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.

The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c
index ff6cab4f6343..7377dca6eb57 100644
--- a/drivers/net/ethernet/micrel/ks8851.c
+++ b/drivers/net/ethernet/micrel/ks8851.c
@@ -870,6 +870,7 @@ static int ks8851_net_open(struct net_device *dev)
 	netif_dbg(ks, ifup, ks->netdev, "network device up\n");
 
 	mutex_unlock(&ks->lock);
+	mii_check_link(&ks->mii);
 	return 0;
 }
 
@@ -1527,6 +1528,7 @@ static int ks8851_probe(struct spi_device *spi)
 
 	spi_set_drvdata(spi, ks);
 
+	netif_carrier_off(ks->netdev);
 	ndev->if_port = IF_PORT_100BASET;
 	ndev->netdev_ops = &ks8851_netdev_ops;
 	ndev->irq = spi->irq;
-- 
2.19.1

[PATCH AUTOSEL 4.9 16/29] staging: rtl8712: uninitialized memory in read_bbreg_hdl()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 22c971db7dd4b0ad8dd88e99c407f7a1f4231a2e ]

Colin King reported a bug in read_bbreg_hdl():

	memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);

The problem is that "val" is uninitialized.

This code is obviously not useful, but so far as I can tell
"pcmd->cmdcode" is never GEN_CMD_CODE(_Read_BBREG) so it's not harmful
either.  For now the easiest fix is to just call r8712_free_cmd_obj()
and return.

Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/staging/rtl8712/rtl8712_cmd.c | 10 +---------
 drivers/staging/rtl8712/rtl8712_cmd.h |  2 +-
 2 files changed, 2 insertions(+), 10 deletions(-)

diff --git a/drivers/staging/rtl8712/rtl8712_cmd.c b/drivers/staging/rtl8712/rtl8712_cmd.c
index 9f61583af150..41b667c8385c 100644
--- a/drivers/staging/rtl8712/rtl8712_cmd.c
+++ b/drivers/staging/rtl8712/rtl8712_cmd.c
@@ -158,17 +158,9 @@ static u8 write_macreg_hdl(struct _adapter *padapter, u8 *pbuf)
 
 static u8 read_bbreg_hdl(struct _adapter *padapter, u8 *pbuf)
 {
-	u32 val;
-	void (*pcmd_callback)(struct _adapter *dev, struct cmd_obj	*pcmd);
 	struct cmd_obj *pcmd  = (struct cmd_obj *)pbuf;
 
-	if (pcmd->rsp && pcmd->rspsz > 0)
-		memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);
-	pcmd_callback = cmd_callback[pcmd->cmdcode].callback;
-	if (!pcmd_callback)
-		r8712_free_cmd_obj(pcmd);
-	else
-		pcmd_callback(padapter, pcmd);
+	r8712_free_cmd_obj(pcmd);
 	return H2C_SUCCESS;
 }
 
diff --git a/drivers/staging/rtl8712/rtl8712_cmd.h b/drivers/staging/rtl8712/rtl8712_cmd.h
index 67e9e910aef9..d10a59d4a550 100644
--- a/drivers/staging/rtl8712/rtl8712_cmd.h
+++ b/drivers/staging/rtl8712/rtl8712_cmd.h
@@ -152,7 +152,7 @@ enum rtl8712_h2c_cmd {
 static struct _cmd_callback	cmd_callback[] = {
 	{GEN_CMD_CODE(_Read_MACREG), NULL}, /*0*/
 	{GEN_CMD_CODE(_Write_MACREG), NULL},
-	{GEN_CMD_CODE(_Read_BBREG), &r8712_getbbrfreg_cmdrsp_callback},
+	{GEN_CMD_CODE(_Read_BBREG), NULL},
 	{GEN_CMD_CODE(_Write_BBREG), NULL},
 	{GEN_CMD_CODE(_Read_RFREG), &r8712_getbbrfreg_cmdrsp_callback},
 	{GEN_CMD_CODE(_Write_RFREG), NULL}, /*5*/
-- 
2.19.1

[PATCH AUTOSEL 4.9 17/29] NFS: Fix a typo in nfs_init_timeout_values()

[Sasha Levin]

From: Trond Myklebust <trond.myklebust@hammerspace.com>

[ Upstream commit 5a698243930c441afccec04e4d5dc8febfd2b775 ]

Specifying a retrans=0 mount parameter to a NFS/TCP mount, is
inadvertently causing the NFS client to rewrite any specified
timeout parameter to the default of 60 seconds.

Fixes: a956beda19a6 ("NFS: Allow the mount option retrans=0")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 fs/nfs/client.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/nfs/client.c b/fs/nfs/client.c
index ebecfb8fba06..28d8a57a9908 100644
--- a/fs/nfs/client.c
+++ b/fs/nfs/client.c
@@ -440,7 +440,7 @@ void nfs_init_timeout_values(struct rpc_timeout *to, int proto,
 	case XPRT_TRANSPORT_RDMA:
 		if (retrans == NFS_UNSPEC_RETRANS)
 			to->to_retries = NFS_DEF_TCP_RETRANS;
-		if (timeo == NFS_UNSPEC_TIMEO || to->to_retries == 0)
+		if (timeo == NFS_UNSPEC_TIMEO || to->to_initval == 0)
 			to->to_initval = NFS_DEF_TCP_TIMEO * HZ / 10;
 		if (to->to_initval > NFS_MAX_TCP_TIMEOUT)
 			to->to_initval = NFS_MAX_TCP_TIMEOUT;
-- 
2.19.1

[PATCH AUTOSEL 4.9 18/29] net: xilinx: fix possible object reference leak

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit fa3a419d2f674b431d38748cb58fb7da17ee8949 ]

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index c688d68c39aa..a8afc92cbfca 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -1548,12 +1548,14 @@ static int axienet_probe(struct platform_device *pdev)
 	ret = of_address_to_resource(np, 0, &dmares);
 	if (ret) {
 		dev_err(&pdev->dev, "unable to get DMA resource\n");
+		of_node_put(np);
 		goto free_netdev;
 	}
 	lp->dma_regs = devm_ioremap_resource(&pdev->dev, &dmares);
 	if (IS_ERR(lp->dma_regs)) {
 		dev_err(&pdev->dev, "could not map DMA regs\n");
 		ret = PTR_ERR(lp->dma_regs);
+		of_node_put(np);
 		goto free_netdev;
 	}
 	lp->rx_irq = irq_of_parse_and_map(np, 1);
-- 
2.19.1

[PATCH AUTOSEL 4.9 19/29] net: ibm: fix possible object reference leak

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit be693df3cf9dd113ff1d2c0d8150199efdba37f6 ]

The call to ehea_get_eth_dn returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Douglas Miller <dougmill@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/ibm/ehea/ehea_main.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/ibm/ehea/ehea_main.c b/drivers/net/ethernet/ibm/ehea/ehea_main.c
index bd719e25dd76..2dd17e01e3a7 100644
--- a/drivers/net/ethernet/ibm/ehea/ehea_main.c
+++ b/drivers/net/ethernet/ibm/ehea/ehea_main.c
@@ -3184,6 +3184,7 @@ static ssize_t ehea_probe_port(struct device *dev,
 
 	if (ehea_add_adapter_mr(adapter)) {
 		pr_err("creating MR failed\n");
+		of_node_put(eth_dn);
 		return -EIO;
 	}
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 20/29] net: ethernet: ti: fix possible object reference leak

[Sasha Levin]

From: Wen Yang <wen.yang99@zte.com.cn>

[ Upstream commit 75eac7b5f68b0a0671e795ac636457ee27cc11d8 ]

The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.

Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/net/ethernet/ti/netcp_ethss.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/ti/netcp_ethss.c b/drivers/net/ethernet/ti/netcp_ethss.c
index d543298d6750..ff24524e7f46 100644
--- a/drivers/net/ethernet/ti/netcp_ethss.c
+++ b/drivers/net/ethernet/ti/netcp_ethss.c
@@ -3122,12 +3122,16 @@ static int gbe_probe(struct netcp_device *netcp_device, struct device *dev,
 
 	ret = netcp_txpipe_init(&gbe_dev->tx_pipe, netcp_device,
 				gbe_dev->dma_chan_name, gbe_dev->tx_queue_id);
-	if (ret)
+	if (ret) {
+		of_node_put(interfaces);
 		return ret;
+	}
 
 	ret = netcp_txpipe_open(&gbe_dev->tx_pipe);
-	if (ret)
+	if (ret) {
+		of_node_put(interfaces);
 		return ret;
+	}
 
 	/* Create network interfaces */
 	INIT_LIST_HEAD(&gbe_dev->gbe_intf_head);
-- 
2.19.1

[PATCH AUTOSEL 4.9 21/29] scsi: qla4xxx: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit fba1bdd2a9a93f3e2181ec1936a3c2f6b37e7ed6 ]

In case iscsi_lookup_endpoint fails, the fix returns -EINVAL to avoid NULL
pointer dereference.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/scsi/qla4xxx/ql4_os.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c
index f9f899ec9427..c158967b59d7 100644
--- a/drivers/scsi/qla4xxx/ql4_os.c
+++ b/drivers/scsi/qla4xxx/ql4_os.c
@@ -3207,6 +3207,8 @@ static int qla4xxx_conn_bind(struct iscsi_cls_session *cls_session,
 	if (iscsi_conn_bind(cls_session, cls_conn, is_leading))
 		return -EINVAL;
 	ep = iscsi_lookup_endpoint(transport_fd);
+	if (!ep)
+		return -EINVAL;
 	conn = cls_conn->dd_data;
 	qla_conn = conn->dd_data;
 	qla_conn->qla_ep = ep->dd_data;
-- 
2.19.1

[PATCH AUTOSEL 4.9 22/29] usb: u132-hcd: fix resource leak

[Sasha Levin]

From: Mukesh Ojha <mojha@codeaurora.org>

[ Upstream commit f276e002793cdb820862e8ea8f76769d56bba575 ]

if platform_driver_register fails, cleanup the allocated resource
gracefully.

Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/usb/host/u132-hcd.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c
index 43618976d68a..3efb7b0e8269 100644
--- a/drivers/usb/host/u132-hcd.c
+++ b/drivers/usb/host/u132-hcd.c
@@ -3208,6 +3208,9 @@ static int __init u132_hcd_init(void)
 	printk(KERN_INFO "driver %s\n", hcd_name);
 	workqueue = create_singlethread_workqueue("u132");
 	retval = platform_driver_register(&u132_platform_driver);
+	if (retval)
+		destroy_workqueue(workqueue);
+
 	return retval;
 }
 
-- 
2.19.1

[PATCH AUTOSEL 4.9 23/29] tty: fix NULL pointer issue when tty_port ops is not set

[Sasha Levin]

From: Fabien Dessenne <fabien.dessenne@st.com>

[ Upstream commit f4e68d58cf2b20a581759bbc7228052534652673 ]

Unlike 'client_ops' which is initialized to 'default_client_ops', the
port operations 'ops' may be left to NULL.
Check the 'ops' value before checking the 'ops->x' value.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/tty/tty_port.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c
index 7f2f20b74d1d..06ba9dbbd610 100644
--- a/drivers/tty/tty_port.c
+++ b/drivers/tty/tty_port.c
@@ -213,7 +213,7 @@ static void tty_port_shutdown(struct tty_port *port, struct tty_struct *tty)
 		if (tty && C_HUPCL(tty))
 			tty_port_lower_dtr_rts(port);
 
-		if (port->ops->shutdown)
+		if (port->ops && port->ops->shutdown)
 			port->ops->shutdown(port);
 	}
 out:
@@ -293,7 +293,7 @@ EXPORT_SYMBOL_GPL(tty_port_tty_wakeup);
 
 int tty_port_carrier_raised(struct tty_port *port)
 {
-	if (port->ops->carrier_raised == NULL)
+	if (!port->ops || !port->ops->carrier_raised)
 		return 1;
 	return port->ops->carrier_raised(port);
 }
@@ -310,7 +310,7 @@ EXPORT_SYMBOL(tty_port_carrier_raised);
 
 void tty_port_raise_dtr_rts(struct tty_port *port)
 {
-	if (port->ops->dtr_rts)
+	if (port->ops && port->ops->dtr_rts)
 		port->ops->dtr_rts(port, 1);
 }
 EXPORT_SYMBOL(tty_port_raise_dtr_rts);
@@ -326,7 +326,7 @@ EXPORT_SYMBOL(tty_port_raise_dtr_rts);
 
 void tty_port_lower_dtr_rts(struct tty_port *port)
 {
-	if (port->ops->dtr_rts)
+	if (port->ops && port->ops->dtr_rts)
 		port->ops->dtr_rts(port, 0);
 }
 EXPORT_SYMBOL(tty_port_lower_dtr_rts);
@@ -582,7 +582,7 @@ int tty_port_open(struct tty_port *port, struct tty_struct *tty,
 
 	if (!tty_port_initialized(port)) {
 		clear_bit(TTY_IO_ERROR, &tty->flags);
-		if (port->ops->activate) {
+		if (port->ops && port->ops->activate) {
 			int retval = port->ops->activate(port, tty);
 			if (retval) {
 				mutex_unlock(&port->mutex);
-- 
2.19.1

[PATCH AUTOSEL 4.9 24/29] ceph: fix use-after-free on symlink traversal

[Sasha Levin]

From: Al Viro <viro@zeniv.linux.org.uk>

[ Upstream commit daf5cc27eed99afdea8d96e71b89ba41f5406ef6 ]

free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 fs/ceph/inode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/ceph/inode.c b/fs/ceph/inode.c
index 30d9d9e7057d..7a4052501866 100644
--- a/fs/ceph/inode.c
+++ b/fs/ceph/inode.c
@@ -523,6 +523,7 @@ static void ceph_i_callback(struct rcu_head *head)
 	struct inode *inode = container_of(head, struct inode, i_rcu);
 	struct ceph_inode_info *ci = ceph_inode(inode);
 
+	kfree(ci->i_symlink);
 	kmem_cache_free(ceph_inode_cachep, ci);
 }
 
@@ -554,7 +555,6 @@ void ceph_destroy_inode(struct inode *inode)
 		ceph_put_snap_realm(mdsc, realm);
 	}
 
-	kfree(ci->i_symlink);
 	while ((n = rb_first(&ci->i_fragtree)) != NULL) {
 		frag = rb_entry(n, struct ceph_inode_frag, node);
 		rb_erase(n, &ci->i_fragtree);
-- 
2.19.1

[PATCH AUTOSEL 4.9 25/29] scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCN

[Sasha Levin]

From: Steffen Maier <maier@linux.ibm.com>

[ Upstream commit c8206579175c34a2546de8a74262456278a7795a ]

If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away.  It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.

The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.

The call chain was:

  zfcp_fc_incoming_rscn
    for (i = 1; i < no_entries; i++)
      _zfcp_fc_incoming_rscn
        list_for_each_entry(port, &adapter->port_list, list)
          if (masked port->d_id match) zfcp_fc_test_link
          if (!port->d_id) zfcp_erp_port_reopen "fcrscn1"   <===

In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:

  zfcp_fc_incoming_rscn
    if (no_entries > 1)                                     <===
      list_for_each_entry(port, &adapter->port_list, list)  <===
        if (!port->d_id) zfcp_erp_port_reopen "fcrscn1"     <===
    for (i = 1; i < no_entries; i++)
      _zfcp_fc_incoming_rscn
        list_for_each_entry(port, &adapter->port_list, list)
          if (masked port->d_id match) zfcp_fc_test_link

Abbreviated example trace records before this code change:

Tag            : fcrscn1
WWPN           : 0x500507630310d327
ERP want       : 0x02
ERP need       : 0x02

Tag            : fcrscn1
WWPN           : 0x500507630310d327
ERP want       : 0x02
ERP need       : 0x00                 NOP => superfluous trace record

The last trace entry repeats if there are more than 2 RSCN elements.

Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/s390/scsi/zfcp_fc.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c
index 237688af179b..f7630cf581cd 100644
--- a/drivers/s390/scsi/zfcp_fc.c
+++ b/drivers/s390/scsi/zfcp_fc.c
@@ -238,10 +238,6 @@ static void _zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req, u32 range,
 	list_for_each_entry(port, &adapter->port_list, list) {
 		if ((port->d_id & range) == (ntoh24(page->rscn_fid) & range))
 			zfcp_fc_test_link(port);
-		if (!port->d_id)
-			zfcp_erp_port_reopen(port,
-					     ZFCP_STATUS_COMMON_ERP_FAILED,
-					     "fcrscn1");
 	}
 	read_unlock_irqrestore(&adapter->port_list_lock, flags);
 }
@@ -249,6 +245,7 @@ static void _zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req, u32 range,
 static void zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req)
 {
 	struct fsf_status_read_buffer *status_buffer = (void *)fsf_req->data;
+	struct zfcp_adapter *adapter = fsf_req->adapter;
 	struct fc_els_rscn *head;
 	struct fc_els_rscn_page *page;
 	u16 i;
@@ -261,6 +258,22 @@ static void zfcp_fc_incoming_rscn(struct zfcp_fsf_req *fsf_req)
 	/* see FC-FS */
 	no_entries = head->rscn_plen / sizeof(struct fc_els_rscn_page);
 
+	if (no_entries > 1) {
+		/* handle failed ports */
+		unsigned long flags;
+		struct zfcp_port *port;
+
+		read_lock_irqsave(&adapter->port_list_lock, flags);
+		list_for_each_entry(port, &adapter->port_list, list) {
+			if (port->d_id)
+				continue;
+			zfcp_erp_port_reopen(port,
+					     ZFCP_STATUS_COMMON_ERP_FAILED,
+					     "fcrscn1");
+		}
+		read_unlock_irqrestore(&adapter->port_list_lock, flags);
+	}
+
 	for (i = 1; i < no_entries; i++) {
 		/* skip head and start with 1st element */
 		page++;
-- 
2.19.1

[PATCH AUTOSEL 4.9 26/29] libata: fix using DMA buffers on stack

[Sasha Levin]

From: raymond pang <raymondpangxd@gmail.com>

[ Upstream commit dd08a8d9a66de4b54575c294a92630299f7e0fe7 ]

When CONFIG_VMAP_STACK=y, __pa() returns incorrect physical address for
a stack virtual address. Stack DMA buffers must be avoided.

Signed-off-by: raymond pang <raymondpangxd@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/ata/libata-zpodd.c | 34 ++++++++++++++++++++++++----------
 1 file changed, 24 insertions(+), 10 deletions(-)

diff --git a/drivers/ata/libata-zpodd.c b/drivers/ata/libata-zpodd.c
index 0ad96c647541..7017a81d53cf 100644
--- a/drivers/ata/libata-zpodd.c
+++ b/drivers/ata/libata-zpodd.c
@@ -51,38 +51,52 @@ static int eject_tray(struct ata_device *dev)
 /* Per the spec, only slot type and drawer type ODD can be supported */
 static enum odd_mech_type zpodd_get_mech_type(struct ata_device *dev)
 {
-	char buf[16];
+	char *buf;
 	unsigned int ret;
-	struct rm_feature_desc *desc = (void *)(buf + 8);
+	struct rm_feature_desc *desc;
 	struct ata_taskfile tf;
 	static const char cdb[] = {  GPCMD_GET_CONFIGURATION,
 			2,      /* only 1 feature descriptor requested */
 			0, 3,   /* 3, removable medium feature */
 			0, 0, 0,/* reserved */
-			0, sizeof(buf),
+			0, 16,
 			0, 0, 0,
 	};
 
+	buf = kzalloc(16, GFP_KERNEL);
+	if (!buf)
+		return ODD_MECH_TYPE_UNSUPPORTED;
+	desc = (void *)(buf + 8);
+
 	ata_tf_init(dev, &tf);
 	tf.flags = ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
 	tf.command = ATA_CMD_PACKET;
 	tf.protocol = ATAPI_PROT_PIO;
-	tf.lbam = sizeof(buf);
+	tf.lbam = 16;
 
 	ret = ata_exec_internal(dev, &tf, cdb, DMA_FROM_DEVICE,
-				buf, sizeof(buf), 0);
-	if (ret)
+				buf, 16, 0);
+	if (ret) {
+		kfree(buf);
 		return ODD_MECH_TYPE_UNSUPPORTED;
+	}
 
-	if (be16_to_cpu(desc->feature_code) != 3)
+	if (be16_to_cpu(desc->feature_code) != 3) {
+		kfree(buf);
 		return ODD_MECH_TYPE_UNSUPPORTED;
+	}
 
-	if (desc->mech_type == 0 && desc->load == 0 && desc->eject == 1)
+	if (desc->mech_type == 0 && desc->load == 0 && desc->eject == 1) {
+		kfree(buf);
 		return ODD_MECH_TYPE_SLOT;
-	else if (desc->mech_type == 1 && desc->load == 0 && desc->eject == 1)
+	} else if (desc->mech_type == 1 && desc->load == 0 &&
+		   desc->eject == 1) {
+		kfree(buf);
 		return ODD_MECH_TYPE_DRAWER;
-	else
+	} else {
+		kfree(buf);
 		return ODD_MECH_TYPE_UNSUPPORTED;
+	}
 }
 
 /* Test if ODD is zero power ready by sense code */
-- 
2.19.1

[PATCH AUTOSEL 4.9 27/29] gpio: of: Fix of_gpiochip_add() error path

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit f7299d441a4da8a5088e651ea55023525a793a13 ]

If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no
error handling is performed.  This lead to the need of callers to call
of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..."
if the failure happened before the call to of_node_get().

Fix this by adding proper error handling.

Note that calling gpiochip_remove_pin_ranges() multiple times causes no
harm: subsequent calls are a no-op.

Fixes: dfbd379ba9b7431e ("gpio: of: Return error if gpio hog configuration failed")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/gpio/gpiolib-of.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index aac84329c759..b863386be911 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -531,7 +531,13 @@ int of_gpiochip_add(struct gpio_chip *chip)
 
 	of_node_get(chip->of_node);
 
-	return of_gpiochip_scan_gpios(chip);
+	status = of_gpiochip_scan_gpios(chip);
+	if (status) {
+		of_node_put(chip->of_node);
+		gpiochip_remove_pin_ranges(chip);
+	}
+
+	return status;
 }
 
 void of_gpiochip_remove(struct gpio_chip *chip)
-- 
2.19.1

[PATCH AUTOSEL 4.9 28/29] kconfig/[mn]conf: handle backspace (^H) key

[Sasha Levin]

From: Changbin Du <changbin.du@gmail.com>

[ Upstream commit 9c38f1f044080392603c497ecca4d7d09876ff99 ]

Backspace is not working on some terminal emulators which do not send the
key code defined by terminfo. Terminals either send '^H' (8) or '^?' (127).
But currently only '^?' is handled. Let's also handle '^H' for those
terminals.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 scripts/kconfig/lxdialog/inputbox.c | 3 ++-
 scripts/kconfig/nconf.c             | 2 +-
 scripts/kconfig/nconf.gui.c         | 3 ++-
 3 files changed, 5 insertions(+), 3 deletions(-)

diff --git a/scripts/kconfig/lxdialog/inputbox.c b/scripts/kconfig/lxdialog/inputbox.c
index d58de1dc5360..510049a7bd1d 100644
--- a/scripts/kconfig/lxdialog/inputbox.c
+++ b/scripts/kconfig/lxdialog/inputbox.c
@@ -126,7 +126,8 @@ int dialog_inputbox(const char *title, const char *prompt, int height, int width
 			case KEY_DOWN:
 				break;
 			case KEY_BACKSPACE:
-			case 127:
+			case 8:   /* ^H */
+			case 127: /* ^? */
 				if (pos) {
 					wattrset(dialog, dlg.inputbox.atr);
 					if (input_x == 0) {
diff --git a/scripts/kconfig/nconf.c b/scripts/kconfig/nconf.c
index d42d534a66cd..f7049e288e93 100644
--- a/scripts/kconfig/nconf.c
+++ b/scripts/kconfig/nconf.c
@@ -1046,7 +1046,7 @@ static int do_match(int key, struct match_state *state, int *ans)
 		state->match_direction = FIND_NEXT_MATCH_UP;
 		*ans = get_mext_match(state->pattern,
 				state->match_direction);
-	} else if (key == KEY_BACKSPACE || key == 127) {
+	} else if (key == KEY_BACKSPACE || key == 8 || key == 127) {
 		state->pattern[strlen(state->pattern)-1] = '\0';
 		adj_match_dir(&state->match_direction);
 	} else
diff --git a/scripts/kconfig/nconf.gui.c b/scripts/kconfig/nconf.gui.c
index 4b2f44c20caf..9a65035cf787 100644
--- a/scripts/kconfig/nconf.gui.c
+++ b/scripts/kconfig/nconf.gui.c
@@ -439,7 +439,8 @@ int dialog_inputbox(WINDOW *main_window,
 		case KEY_F(F_EXIT):
 		case KEY_F(F_BACK):
 			break;
-		case 127:
+		case 8:   /* ^H */
+		case 127: /* ^? */
 		case KEY_BACKSPACE:
 			if (cursor_position > 0) {
 				memmove(&result[cursor_position-1],
-- 
2.19.1

[PATCH AUTOSEL 4.9 29/29] leds: pca9532: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit 0aab8e4df4702b31314a27ec4b0631dfad0fae0a ]

In case of_match_device cannot find a match, return -EINVAL to avoid
NULL pointer dereference.

Fixes: fa4191a609f2 ("leds: pca9532: Add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
---
 drivers/leds/leds-pca9532.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/leds/leds-pca9532.c b/drivers/leds/leds-pca9532.c
index 09a7cffbc46f..896b38f6f9c0 100644
--- a/drivers/leds/leds-pca9532.c
+++ b/drivers/leds/leds-pca9532.c
@@ -488,6 +488,7 @@ static int pca9532_probe(struct i2c_client *client,
 	const struct i2c_device_id *id)
 {
 	int devid;
+	const struct of_device_id *of_id;
 	struct pca9532_data *data = i2c_get_clientdata(client);
 	struct pca9532_platform_data *pca9532_pdata =
 			dev_get_platdata(&client->dev);
@@ -503,8 +504,11 @@ static int pca9532_probe(struct i2c_client *client,
 			dev_err(&client->dev, "no platform data\n");
 			return -EINVAL;
 		}
-		devid = (int)(uintptr_t)of_match_device(
-			of_pca9532_leds_match, &client->dev)->data;
+		of_id = of_match_device(of_pca9532_leds_match,
+				&client->dev);
+		if (unlikely(!of_id))
+			return -EINVAL;
+		devid = (int)(uintptr_t) of_id->data;
 	} else {
 		devid = id->driver_data;
 	}
-- 
2.19.1