[PATCH v2 0/2] DMA support for AT91 USART in SPI mode

[PATCH v2 0/2] DMA support for AT91 USART in SPI mode

[Radu Pirea]

Hi,

This is the version two of the patches with DMA support for
spi-at91-usart driver. 

Changes in v2:
- specified in bindings order of dmas and dma-names
- changed DMA_FROM_DEVICE to DMA_DEV_TO_MEM and DMA_TO_DEVICE to
DMA_MEM_TO_DEV when dmaengine_prep_slave_sg is called

Changes in v1:
- added DMA support


Radu Pirea (2):
  dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode
  spi: at91-usart: add DMA support

 .../devicetree/bindings/mfd/atmel-usart.txt   |  20 +-
 drivers/spi/spi-at91-usart.c                  | 221 +++++++++++++++++-
 2 files changed, 234 insertions(+), 7 deletions(-)

-- 
2.21.0

[PATCH v2 1/2] dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode

[Radu Pirea]

The bindings for DMA are now common for both drivers of the USART
IP.

The node given as an example for USART in SPI mode has been updated in
order to include DMA bindings.

Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
---
 .../devicetree/bindings/mfd/atmel-usart.txt   | 20 ++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
index 7f0cd72f47d2..699fd3c9ace8 100644
--- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -17,17 +17,24 @@ Required properties for USART in SPI mode:
 - cs-gpios: chipselects (internal cs not supported)
 - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
 
+Optional properties in serial and SPI mode:
+- dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		The order of DMA channels is fixed. The first DMA channel must be TX
+		associated channel and the second one must be RX associated channel.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "tx" for TX channel.
+		     "rx" for RX channel.
+		     The order of dma-names is also fixed. The first name must be "tx"
+		     and the second one must be "rx" as in the examples below.
+
 Optional properties in serial mode:
 - atmel,use-dma-rx: use of PDC or DMA for receiving data
 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
   It will use specified PIO instead of the peripheral function pin for the USART feature.
   If unsure, don't specify this property.
-- add dma bindings for dma transfer:
-	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
-		memory peripheral interface and USART DMA channel ID, FIFO configuration.
-		Refer to dma.txt and atmel-dma.txt for details.
-	- dma-names: "rx" for RX channel, "tx" for TX channel.
 - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
   capable USARTs.
 - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
@@ -81,5 +88,8 @@ Example:
 		interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 		clocks = <&usart0_clk>;
 		clock-names = "usart";
+		dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
+		       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+		dma-names = "tx", "rx";
 		cs-gpios = <&pioB 3 0>;
 	};
-- 
2.21.0

[PATCH v2 2/2] spi: at91-usart: add DMA support

[Radu Pirea]

This patch adds support for DMA. Transfers are done with dma only if
they are longer than 16 bytes in order to achieve a better performance.
DMA setup introduces a little overhead and for transfers shorter than 16
bytes there is no performance improvement.

Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
---
 drivers/spi/spi-at91-usart.c | 221 ++++++++++++++++++++++++++++++++++-
 1 file changed, 219 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-at91-usart.c b/drivers/spi/spi-at91-usart.c
index a694d702e574..f3583bdd475b 100644
--- a/drivers/spi/spi-at91-usart.c
+++ b/drivers/spi/spi-at91-usart.c
@@ -8,9 +8,12 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-direction.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_platform.h>
 #include <linux/of_gpio.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
@@ -59,6 +62,8 @@
 
 #define US_INIT \
 	(US_MR_SPI_MASTER | US_MR_CHRL | US_MR_CLKO | US_MR_WRDBT)
+#define US_DMA_MIN_BYTES       16
+#define US_DMA_TIMEOUT         (msecs_to_jiffies(1000))
 
 /* Register access macros */
 #define at91_usart_spi_readl(port, reg) \
@@ -72,14 +77,19 @@
 	writeb_relaxed((value), (port)->regs + US_##reg)
 
 struct at91_usart_spi {
+	struct platform_device  *mpdev;
 	struct spi_transfer	*current_transfer;
 	void __iomem		*regs;
 	struct device		*dev;
 	struct clk		*clk;
 
+	struct completion	xfer_completion;
+
 	/*used in interrupt to protect data reading*/
 	spinlock_t		lock;
 
+	phys_addr_t		phybase;
+
 	int			irq;
 	unsigned int		current_tx_remaining_bytes;
 	unsigned int		current_rx_remaining_bytes;
@@ -88,8 +98,182 @@ struct at91_usart_spi {
 	u32			status;
 
 	bool			xfer_failed;
+	bool			use_dma;
 };
 
+static void dma_callback(void *data)
+{
+	struct spi_controller   *ctlr = data;
+	struct at91_usart_spi   *aus = spi_master_get_devdata(ctlr);
+
+	at91_usart_spi_writel(aus, IER, US_IR_RXRDY);
+	aus->current_rx_remaining_bytes = 0;
+	complete(&aus->xfer_completion);
+}
+
+static bool at91_usart_spi_can_dma(struct spi_controller *ctrl,
+				   struct spi_device *spi,
+				   struct spi_transfer *xfer)
+{
+	struct at91_usart_spi *aus = spi_master_get_devdata(ctrl);
+
+	return aus->use_dma && xfer->len >= US_DMA_MIN_BYTES;
+}
+
+static int at91_usart_spi_configure_dma(struct spi_controller *ctlr,
+					struct at91_usart_spi *aus)
+{
+	struct dma_slave_config slave_config;
+	struct device *dev = &aus->mpdev->dev;
+	phys_addr_t phybase = aus->phybase;
+	dma_cap_mask_t mask;
+	int err = 0;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+
+	ctlr->dma_tx = dma_request_slave_channel_reason(dev, "tx");
+	if (IS_ERR_OR_NULL(ctlr->dma_tx)) {
+		if (IS_ERR(ctlr->dma_tx)) {
+			err = PTR_ERR(ctlr->dma_tx);
+			goto at91_usart_spi_error_clear;
+		}
+
+		dev_dbg(dev,
+			"DMA TX channel not available, SPI unable to use DMA\n");
+		err = -EBUSY;
+		goto at91_usart_spi_error_clear;
+	}
+
+	ctlr->dma_rx = dma_request_slave_channel_reason(dev, "rx");
+	if (IS_ERR_OR_NULL(ctlr->dma_rx)) {
+		if (IS_ERR(ctlr->dma_rx)) {
+			err = PTR_ERR(ctlr->dma_rx);
+			goto at91_usart_spi_error;
+		}
+
+		dev_dbg(dev,
+			"DMA RX channel not available, SPI unable to use DMA\n");
+		err = -EBUSY;
+		goto at91_usart_spi_error;
+	}
+
+	slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	slave_config.dst_addr = (dma_addr_t)phybase + US_THR;
+	slave_config.src_addr = (dma_addr_t)phybase + US_RHR;
+	slave_config.src_maxburst = 1;
+	slave_config.dst_maxburst = 1;
+	slave_config.device_fc = false;
+
+	slave_config.direction = DMA_DEV_TO_MEM;
+	if (dmaengine_slave_config(ctlr->dma_rx, &slave_config)) {
+		dev_err(&ctlr->dev,
+			"failed to configure rx dma channel\n");
+		err = -EINVAL;
+		goto at91_usart_spi_error;
+	}
+
+	slave_config.direction = DMA_MEM_TO_DEV;
+	if (dmaengine_slave_config(ctlr->dma_tx, &slave_config)) {
+		dev_err(&ctlr->dev,
+			"failed to configure tx dma channel\n");
+		err = -EINVAL;
+		goto at91_usart_spi_error;
+	}
+
+	aus->use_dma = true;
+	return 0;
+
+at91_usart_spi_error:
+	if (!IS_ERR_OR_NULL(ctlr->dma_tx))
+		dma_release_channel(ctlr->dma_tx);
+	if (!IS_ERR_OR_NULL(ctlr->dma_rx))
+		dma_release_channel(ctlr->dma_rx);
+	ctlr->dma_tx = NULL;
+	ctlr->dma_rx = NULL;
+
+at91_usart_spi_error_clear:
+	return err;
+}
+
+static void at91_usart_spi_release_dma(struct spi_controller *ctlr)
+{
+	if (ctlr->dma_rx)
+		dma_release_channel(ctlr->dma_rx);
+	if (ctlr->dma_tx)
+		dma_release_channel(ctlr->dma_tx);
+}
+
+static void at91_usart_spi_stop_dma(struct spi_controller *ctlr)
+{
+	if (ctlr->dma_rx)
+		dmaengine_terminate_all(ctlr->dma_rx);
+	if (ctlr->dma_tx)
+		dmaengine_terminate_all(ctlr->dma_tx);
+}
+
+static int at91_usart_spi_dma_transfer(struct spi_controller *ctlr,
+				       struct spi_transfer *xfer)
+{
+	struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+	struct dma_chan	 *rxchan = ctlr->dma_rx;
+	struct dma_chan *txchan = ctlr->dma_tx;
+	struct dma_async_tx_descriptor *rxdesc;
+	struct dma_async_tx_descriptor *txdesc;
+	dma_cookie_t cookie;
+
+	/* Disable RX interrupt */
+	at91_usart_spi_writel(aus, IDR, US_IR_RXRDY);
+
+	rxdesc = dmaengine_prep_slave_sg(rxchan,
+					 xfer->rx_sg.sgl,
+					 xfer->rx_sg.nents,
+					 DMA_DEV_TO_MEM,
+					 DMA_PREP_INTERRUPT |
+					 DMA_CTRL_ACK);
+	if (!rxdesc)
+		goto at91_usart_spi_err_dma;
+
+	txdesc = dmaengine_prep_slave_sg(txchan,
+					 xfer->tx_sg.sgl,
+					 xfer->tx_sg.nents,
+					 DMA_MEM_TO_DEV,
+					 DMA_PREP_INTERRUPT |
+					 DMA_CTRL_ACK);
+	if (!txdesc)
+		goto at91_usart_spi_err_dma;
+
+	rxdesc->callback = dma_callback;
+	rxdesc->callback_param = ctlr;
+
+	cookie = rxdesc->tx_submit(rxdesc);
+	if (dma_submit_error(cookie))
+		goto at91_usart_spi_err_dma;
+
+	cookie = txdesc->tx_submit(txdesc);
+	if (dma_submit_error(cookie))
+		goto at91_usart_spi_err_dma;
+
+	rxchan->device->device_issue_pending(rxchan);
+	txchan->device->device_issue_pending(txchan);
+
+	return 0;
+
+at91_usart_spi_err_dma:
+	/* Enable RX interrupt if something fails and fallback to PIO */
+	at91_usart_spi_writel(aus, IER, US_IR_RXRDY);
+	at91_usart_spi_stop_dma(ctlr);
+
+	return -ENOMEM;
+}
+
+static unsigned long at91_usart_spi_dma_timeout(struct at91_usart_spi *aus)
+{
+	return wait_for_completion_timeout(&aus->xfer_completion,
+					   US_DMA_TIMEOUT);
+}
+
 static inline u32 at91_usart_spi_tx_ready(struct at91_usart_spi *aus)
 {
 	return aus->status & US_IR_TXRDY;
@@ -222,6 +406,8 @@ static int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
 				       struct spi_transfer *xfer)
 {
 	struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+	unsigned long dma_timeout = 0;
+	int ret = 0;
 
 	at91_usart_spi_set_xfer_speed(aus, xfer);
 	aus->xfer_failed = false;
@@ -231,8 +417,25 @@ static int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
 
 	while ((aus->current_tx_remaining_bytes ||
 		aus->current_rx_remaining_bytes) && !aus->xfer_failed) {
-		at91_usart_spi_read_status(aus);
-		at91_usart_spi_tx(aus);
+		reinit_completion(&aus->xfer_completion);
+		if (at91_usart_spi_can_dma(ctlr, spi, xfer) &&
+		    !ret) {
+			ret = at91_usart_spi_dma_transfer(ctlr, xfer);
+			if (ret)
+				continue;
+
+			dma_timeout = at91_usart_spi_dma_timeout(aus);
+
+			if (WARN_ON(dma_timeout == 0)) {
+				dev_err(&spi->dev, "DMA transfer timeout\n");
+				return -EIO;
+			}
+			aus->current_tx_remaining_bytes = 0;
+		} else {
+			at91_usart_spi_read_status(aus);
+			at91_usart_spi_tx(aus);
+		}
+
 		cpu_relax();
 	}
 
@@ -351,6 +554,7 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	controller->transfer_one = at91_usart_spi_transfer_one;
 	controller->prepare_message = at91_usart_spi_prepare_message;
 	controller->unprepare_message = at91_usart_spi_unprepare_message;
+	controller->can_dma = at91_usart_spi_can_dma;
 	controller->cleanup = at91_usart_spi_cleanup;
 	controller->max_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
 						US_MIN_CLK_DIV);
@@ -382,7 +586,17 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	aus->spi_clk = clk_get_rate(clk);
 	at91_usart_spi_init(aus);
 
+	aus->phybase = regs->start;
+
+	aus->mpdev = to_platform_device(pdev->dev.parent);
+
+	ret = at91_usart_spi_configure_dma(controller, aus);
+	if (ret)
+		goto at91_usart_fail_dma;
+
 	spin_lock_init(&aus->lock);
+	init_completion(&aus->xfer_completion);
+
 	ret = devm_spi_register_master(&pdev->dev, controller);
 	if (ret)
 		goto at91_usart_fail_register_master;
@@ -395,6 +609,8 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	return 0;
 
 at91_usart_fail_register_master:
+	at91_usart_spi_release_dma(controller);
+at91_usart_fail_dma:
 	clk_disable_unprepare(clk);
 at91_usart_spi_probe_fail:
 	spi_master_put(controller);
@@ -459,6 +675,7 @@ static int at91_usart_spi_remove(struct platform_device *pdev)
 	struct spi_controller *ctlr = platform_get_drvdata(pdev);
 	struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
 
+	at91_usart_spi_release_dma(ctlr);
 	clk_disable_unprepare(aus->clk);
 
 	return 0;
-- 
2.21.0

Applied "dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode" to the spi tree

[Mark Brown]

The patch

   dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From f7b99e5948e6be8b850eecbb2de1986d26a76b36 Mon Sep 17 00:00:00 2001
From: Radu Pirea <radu_nicolae.pirea@upb.ro>
Date: Sun, 5 May 2019 21:06:45 +0300
Subject: [PATCH] dt-bindings: mfd: atmel-usart: add DMA bindings for USART in
 SPI mode

The bindings for DMA are now common for both drivers of the USART
IP.

The node given as an example for USART in SPI mode has been updated in
order to include DMA bindings.

Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 .../devicetree/bindings/mfd/atmel-usart.txt   | 20 ++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
index 7f0cd72f47d2..699fd3c9ace8 100644
--- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -17,17 +17,24 @@ Required properties for USART in SPI mode:
 - cs-gpios: chipselects (internal cs not supported)
 - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
 
+Optional properties in serial and SPI mode:
+- dma bindings for dma transfer:
+	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+		memory peripheral interface and USART DMA channel ID, FIFO configuration.
+		The order of DMA channels is fixed. The first DMA channel must be TX
+		associated channel and the second one must be RX associated channel.
+		Refer to dma.txt and atmel-dma.txt for details.
+	- dma-names: "tx" for TX channel.
+		     "rx" for RX channel.
+		     The order of dma-names is also fixed. The first name must be "tx"
+		     and the second one must be "rx" as in the examples below.
+
 Optional properties in serial mode:
 - atmel,use-dma-rx: use of PDC or DMA for receiving data
 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
   It will use specified PIO instead of the peripheral function pin for the USART feature.
   If unsure, don't specify this property.
-- add dma bindings for dma transfer:
-	- dmas: DMA specifier, consisting of a phandle to DMA controller node,
-		memory peripheral interface and USART DMA channel ID, FIFO configuration.
-		Refer to dma.txt and atmel-dma.txt for details.
-	- dma-names: "rx" for RX channel, "tx" for TX channel.
 - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
   capable USARTs.
 - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
@@ -81,5 +88,8 @@ Example:
 		interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 		clocks = <&usart0_clk>;
 		clock-names = "usart";
+		dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
+		       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+		dma-names = "tx", "rx";
 		cs-gpios = <&pioB 3 0>;
 	};
-- 
2.20.1

Applied "spi: at91-usart: add DMA support" to the spi tree

[Mark Brown]

The patch

   spi: at91-usart: add DMA support

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-5.3

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

From c3fdefc2d79e38d20e955d2d3ad48261d99c2936 Mon Sep 17 00:00:00 2001
From: Radu Pirea <radu_nicolae.pirea@upb.ro>
Date: Sun, 5 May 2019 21:06:46 +0300
Subject: [PATCH] spi: at91-usart: add DMA support

This patch adds support for DMA. Transfers are done with dma only if
they are longer than 16 bytes in order to achieve a better performance.
DMA setup introduces a little overhead and for transfers shorter than 16
bytes there is no performance improvement.

Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/spi/spi-at91-usart.c | 221 ++++++++++++++++++++++++++++++++++-
 1 file changed, 219 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-at91-usart.c b/drivers/spi/spi-at91-usart.c
index f763e14bdf12..a40bb2ef89dc 100644
--- a/drivers/spi/spi-at91-usart.c
+++ b/drivers/spi/spi-at91-usart.c
@@ -8,9 +8,12 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-direction.h>
 #include <linux/interrupt.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_platform.h>
 #include <linux/of_gpio.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
@@ -59,6 +62,8 @@
 
 #define US_INIT \
 	(US_MR_SPI_MASTER | US_MR_CHRL | US_MR_CLKO | US_MR_WRDBT)
+#define US_DMA_MIN_BYTES       16
+#define US_DMA_TIMEOUT         (msecs_to_jiffies(1000))
 
 /* Register access macros */
 #define at91_usart_spi_readl(port, reg) \
@@ -72,14 +77,19 @@
 	writeb_relaxed((value), (port)->regs + US_##reg)
 
 struct at91_usart_spi {
+	struct platform_device  *mpdev;
 	struct spi_transfer	*current_transfer;
 	void __iomem		*regs;
 	struct device		*dev;
 	struct clk		*clk;
 
+	struct completion	xfer_completion;
+
 	/*used in interrupt to protect data reading*/
 	spinlock_t		lock;
 
+	phys_addr_t		phybase;
+
 	int			irq;
 	unsigned int		current_tx_remaining_bytes;
 	unsigned int		current_rx_remaining_bytes;
@@ -88,8 +98,182 @@ struct at91_usart_spi {
 	u32			status;
 
 	bool			xfer_failed;
+	bool			use_dma;
 };
 
+static void dma_callback(void *data)
+{
+	struct spi_controller   *ctlr = data;
+	struct at91_usart_spi   *aus = spi_master_get_devdata(ctlr);
+
+	at91_usart_spi_writel(aus, IER, US_IR_RXRDY);
+	aus->current_rx_remaining_bytes = 0;
+	complete(&aus->xfer_completion);
+}
+
+static bool at91_usart_spi_can_dma(struct spi_controller *ctrl,
+				   struct spi_device *spi,
+				   struct spi_transfer *xfer)
+{
+	struct at91_usart_spi *aus = spi_master_get_devdata(ctrl);
+
+	return aus->use_dma && xfer->len >= US_DMA_MIN_BYTES;
+}
+
+static int at91_usart_spi_configure_dma(struct spi_controller *ctlr,
+					struct at91_usart_spi *aus)
+{
+	struct dma_slave_config slave_config;
+	struct device *dev = &aus->mpdev->dev;
+	phys_addr_t phybase = aus->phybase;
+	dma_cap_mask_t mask;
+	int err = 0;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+
+	ctlr->dma_tx = dma_request_slave_channel_reason(dev, "tx");
+	if (IS_ERR_OR_NULL(ctlr->dma_tx)) {
+		if (IS_ERR(ctlr->dma_tx)) {
+			err = PTR_ERR(ctlr->dma_tx);
+			goto at91_usart_spi_error_clear;
+		}
+
+		dev_dbg(dev,
+			"DMA TX channel not available, SPI unable to use DMA\n");
+		err = -EBUSY;
+		goto at91_usart_spi_error_clear;
+	}
+
+	ctlr->dma_rx = dma_request_slave_channel_reason(dev, "rx");
+	if (IS_ERR_OR_NULL(ctlr->dma_rx)) {
+		if (IS_ERR(ctlr->dma_rx)) {
+			err = PTR_ERR(ctlr->dma_rx);
+			goto at91_usart_spi_error;
+		}
+
+		dev_dbg(dev,
+			"DMA RX channel not available, SPI unable to use DMA\n");
+		err = -EBUSY;
+		goto at91_usart_spi_error;
+	}
+
+	slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	slave_config.dst_addr = (dma_addr_t)phybase + US_THR;
+	slave_config.src_addr = (dma_addr_t)phybase + US_RHR;
+	slave_config.src_maxburst = 1;
+	slave_config.dst_maxburst = 1;
+	slave_config.device_fc = false;
+
+	slave_config.direction = DMA_DEV_TO_MEM;
+	if (dmaengine_slave_config(ctlr->dma_rx, &slave_config)) {
+		dev_err(&ctlr->dev,
+			"failed to configure rx dma channel\n");
+		err = -EINVAL;
+		goto at91_usart_spi_error;
+	}
+
+	slave_config.direction = DMA_MEM_TO_DEV;
+	if (dmaengine_slave_config(ctlr->dma_tx, &slave_config)) {
+		dev_err(&ctlr->dev,
+			"failed to configure tx dma channel\n");
+		err = -EINVAL;
+		goto at91_usart_spi_error;
+	}
+
+	aus->use_dma = true;
+	return 0;
+
+at91_usart_spi_error:
+	if (!IS_ERR_OR_NULL(ctlr->dma_tx))
+		dma_release_channel(ctlr->dma_tx);
+	if (!IS_ERR_OR_NULL(ctlr->dma_rx))
+		dma_release_channel(ctlr->dma_rx);
+	ctlr->dma_tx = NULL;
+	ctlr->dma_rx = NULL;
+
+at91_usart_spi_error_clear:
+	return err;
+}
+
+static void at91_usart_spi_release_dma(struct spi_controller *ctlr)
+{
+	if (ctlr->dma_rx)
+		dma_release_channel(ctlr->dma_rx);
+	if (ctlr->dma_tx)
+		dma_release_channel(ctlr->dma_tx);
+}
+
+static void at91_usart_spi_stop_dma(struct spi_controller *ctlr)
+{
+	if (ctlr->dma_rx)
+		dmaengine_terminate_all(ctlr->dma_rx);
+	if (ctlr->dma_tx)
+		dmaengine_terminate_all(ctlr->dma_tx);
+}
+
+static int at91_usart_spi_dma_transfer(struct spi_controller *ctlr,
+				       struct spi_transfer *xfer)
+{
+	struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+	struct dma_chan	 *rxchan = ctlr->dma_rx;
+	struct dma_chan *txchan = ctlr->dma_tx;
+	struct dma_async_tx_descriptor *rxdesc;
+	struct dma_async_tx_descriptor *txdesc;
+	dma_cookie_t cookie;
+
+	/* Disable RX interrupt */
+	at91_usart_spi_writel(aus, IDR, US_IR_RXRDY);
+
+	rxdesc = dmaengine_prep_slave_sg(rxchan,
+					 xfer->rx_sg.sgl,
+					 xfer->rx_sg.nents,
+					 DMA_DEV_TO_MEM,
+					 DMA_PREP_INTERRUPT |
+					 DMA_CTRL_ACK);
+	if (!rxdesc)
+		goto at91_usart_spi_err_dma;
+
+	txdesc = dmaengine_prep_slave_sg(txchan,
+					 xfer->tx_sg.sgl,
+					 xfer->tx_sg.nents,
+					 DMA_MEM_TO_DEV,
+					 DMA_PREP_INTERRUPT |
+					 DMA_CTRL_ACK);
+	if (!txdesc)
+		goto at91_usart_spi_err_dma;
+
+	rxdesc->callback = dma_callback;
+	rxdesc->callback_param = ctlr;
+
+	cookie = rxdesc->tx_submit(rxdesc);
+	if (dma_submit_error(cookie))
+		goto at91_usart_spi_err_dma;
+
+	cookie = txdesc->tx_submit(txdesc);
+	if (dma_submit_error(cookie))
+		goto at91_usart_spi_err_dma;
+
+	rxchan->device->device_issue_pending(rxchan);
+	txchan->device->device_issue_pending(txchan);
+
+	return 0;
+
+at91_usart_spi_err_dma:
+	/* Enable RX interrupt if something fails and fallback to PIO */
+	at91_usart_spi_writel(aus, IER, US_IR_RXRDY);
+	at91_usart_spi_stop_dma(ctlr);
+
+	return -ENOMEM;
+}
+
+static unsigned long at91_usart_spi_dma_timeout(struct at91_usart_spi *aus)
+{
+	return wait_for_completion_timeout(&aus->xfer_completion,
+					   US_DMA_TIMEOUT);
+}
+
 static inline u32 at91_usart_spi_tx_ready(struct at91_usart_spi *aus)
 {
 	return aus->status & US_IR_TXRDY;
@@ -216,6 +400,8 @@ static int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
 				       struct spi_transfer *xfer)
 {
 	struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+	unsigned long dma_timeout = 0;
+	int ret = 0;
 
 	at91_usart_spi_set_xfer_speed(aus, xfer);
 	aus->xfer_failed = false;
@@ -225,8 +411,25 @@ static int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
 
 	while ((aus->current_tx_remaining_bytes ||
 		aus->current_rx_remaining_bytes) && !aus->xfer_failed) {
-		at91_usart_spi_read_status(aus);
-		at91_usart_spi_tx(aus);
+		reinit_completion(&aus->xfer_completion);
+		if (at91_usart_spi_can_dma(ctlr, spi, xfer) &&
+		    !ret) {
+			ret = at91_usart_spi_dma_transfer(ctlr, xfer);
+			if (ret)
+				continue;
+
+			dma_timeout = at91_usart_spi_dma_timeout(aus);
+
+			if (WARN_ON(dma_timeout == 0)) {
+				dev_err(&spi->dev, "DMA transfer timeout\n");
+				return -EIO;
+			}
+			aus->current_tx_remaining_bytes = 0;
+		} else {
+			at91_usart_spi_read_status(aus);
+			at91_usart_spi_tx(aus);
+		}
+
 		cpu_relax();
 	}
 
@@ -345,6 +548,7 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	controller->transfer_one = at91_usart_spi_transfer_one;
 	controller->prepare_message = at91_usart_spi_prepare_message;
 	controller->unprepare_message = at91_usart_spi_unprepare_message;
+	controller->can_dma = at91_usart_spi_can_dma;
 	controller->cleanup = at91_usart_spi_cleanup;
 	controller->max_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
 						US_MIN_CLK_DIV);
@@ -376,7 +580,17 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	aus->spi_clk = clk_get_rate(clk);
 	at91_usart_spi_init(aus);
 
+	aus->phybase = regs->start;
+
+	aus->mpdev = to_platform_device(pdev->dev.parent);
+
+	ret = at91_usart_spi_configure_dma(controller, aus);
+	if (ret)
+		goto at91_usart_fail_dma;
+
 	spin_lock_init(&aus->lock);
+	init_completion(&aus->xfer_completion);
+
 	ret = devm_spi_register_master(&pdev->dev, controller);
 	if (ret)
 		goto at91_usart_fail_register_master;
@@ -389,6 +603,8 @@ static int at91_usart_spi_probe(struct platform_device *pdev)
 	return 0;
 
 at91_usart_fail_register_master:
+	at91_usart_spi_release_dma(controller);
+at91_usart_fail_dma:
 	clk_disable_unprepare(clk);
 at91_usart_spi_probe_fail:
 	spi_master_put(controller);
@@ -453,6 +669,7 @@ static int at91_usart_spi_remove(struct platform_device *pdev)
 	struct spi_controller *ctlr = platform_get_drvdata(pdev);
 	struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
 
+	at91_usart_spi_release_dma(ctlr);
 	clk_disable_unprepare(aus->clk);
 
 	return 0;
-- 
2.20.1

Re: Applied "dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode" to the spi tree

[Lee Jones]

On Wed, 08 May 2019, Mark Brown wrote:

> The patch
> 
>    dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode
> 
> has been applied to the spi tree at
> 
>    https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-5.3
> 
> All being well this means that it will be integrated into the linux-next
> tree (usually sometime in the next 24 hours) and sent to Linus during
> the next merge window (or sooner if it is a bug fix), however if
> problems are discovered then the patch may be dropped or reverted.  
> 
> You may get further e-mails resulting from automated or manual testing
> and review of the tree, please engage with people reporting problems and
> send followup patches addressing any issues that are reported if needed.
> 
> If any updates are required or you are submitting further changes they
> should be sent as incremental updates against current git, existing
> patches will not be replaced.
> 
> Please add any relevant lists and maintainers to the CCs when replying
> to this mail.
> 
> Thanks,
> Mark
> 
> From f7b99e5948e6be8b850eecbb2de1986d26a76b36 Mon Sep 17 00:00:00 2001
> From: Radu Pirea <radu_nicolae.pirea@upb.ro>
> Date: Sun, 5 May 2019 21:06:45 +0300
> Subject: [PATCH] dt-bindings: mfd: atmel-usart: add DMA bindings for USART in
>  SPI mode
> 
> The bindings for DMA are now common for both drivers of the USART
> IP.
> 
> The node given as an example for USART in SPI mode has been updated in
> order to include DMA bindings.
> 
> Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
> Signed-off-by: Mark Brown <broonie@kernel.org>
> ---
>  .../devicetree/bindings/mfd/atmel-usart.txt   | 20 ++++++++++++++-----

Interesting!

-- 
Lee Jones [李琼斯]
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

Re: Applied "dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode" to the spi tree

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 302 bytes --]

On Wed, May 08, 2019 at 11:51:05AM +0100, Lee Jones wrote:
> > Signed-off-by: Mark Brown <broonie@kernel.org>
> > ---
> >  .../devicetree/bindings/mfd/atmel-usart.txt   | 20 ++++++++++++++-----

> Interesting!

For some reason the bindings for the SPI function got put in the MFD
directory, dunno why.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: Applied "dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode" to the spi tree

[Geert Uytterhoeven]

Hi Mark,

On Sun, May 12, 2019 at 7:05 PM Mark Brown <broonie@kernel.org> wrote:
> On Wed, May 08, 2019 at 11:51:05AM +0100, Lee Jones wrote:
> > > Signed-off-by: Mark Brown <broonie@kernel.org>
> > > ---
> > >  .../devicetree/bindings/mfd/atmel-usart.txt   | 20 ++++++++++++++-----
>
> > Interesting!
>
> For some reason the bindings for the SPI function got put in the MFD
> directory, dunno why.

Because this is a block that can do either SPI or USART, hence MFD?

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds