* [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller
2019-05-02 12:32 [PATCH v3 0/5] ARM: rskrza1: Add RZ/A1 IRQC and input switches Geert Uytterhoeven
@ 2019-05-02 12:32 ` Geert Uytterhoeven
2019-05-07 13:51 ` Simon Horman
` (2 more replies)
2019-05-02 12:32 ` [PATCH v3 2/5] irqchip: Add Renesas RZ/A1 Interrupt Controller driver Geert Uytterhoeven
` (3 subsequent siblings)
4 siblings, 3 replies; 15+ messages in thread
From: Geert Uytterhoeven @ 2019-05-02 12:32 UTC (permalink / raw)
To: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Simon Horman, Magnus Damm, Chris Brandt
Cc: devicetree, linux-renesas-soc, linux-kernel, Geert Uytterhoeven
Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v3:
- Use interrupt-map (+ #address-cells and interrupt-map-mask) instead
of renesas,gic-spi-base,
v2:
- Add "renesas,gic-spi-base",
- Document RZ/A2M.
---
.../renesas,rza1-irqc.txt | 43 +++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt
diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt
new file mode 100644
index 0000000000000000..727b7e4cd6e01110
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt
@@ -0,0 +1,43 @@
+DT bindings for the Renesas RZ/A1 Interrupt Controller
+
+The RZ/A1 Interrupt Controller is a front-end for the GIC found on Renesas
+RZ/A1 and RZ/A2 SoCs:
+ - IRQ sense select for 8 external interrupts, 1:1-mapped to 8 GIC SPI
+ interrupts,
+ - NMI edge select.
+
+Required properties:
+ - compatible: Must be "renesas,<soctype>-irqc", and "renesas,rza1-irqc" as
+ fallback.
+ Examples with soctypes are:
+ - "renesas,r7s72100-irqc" (RZ/A1H)
+ - "renesas,r7s9210-irqc" (RZ/A2M)
+ - #interrupt-cells: Must be 2 (an interrupt index and flags, as defined
+ in interrupts.txt in this directory)
+ - #address-cells: Must be zero
+ - interrupt-controller: Marks the device as an interrupt controller
+ - reg: Base address and length of the memory resource used by the interrupt
+ controller
+ - interrupt-map: Specifies the mapping from external interrupts to GIC
+ interrupts
+ - interrupt-map-mask: Must be <7 0>
+
+Example:
+
+ irqc: interrupt-controller@fcfef800 {
+ compatible = "renesas,r7s72100-irqc", "renesas,rza1-irqc";
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0xfcfef800 0x6>;
+ interrupt-map =
+ <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-map-mask = <7 0>;
+ };
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller
2019-05-02 12:32 ` [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller Geert Uytterhoeven
@ 2019-05-07 13:51 ` Simon Horman
2019-05-13 12:17 ` Simon Horman
2019-05-13 17:20 ` Rob Herring
2019-12-11 15:32 ` Geert Uytterhoeven
2 siblings, 1 reply; 15+ messages in thread
From: Simon Horman @ 2019-05-07 13:51 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel
On Thu, May 02, 2019 at 02:32:16PM +0200, Geert Uytterhoeven wrote:
> Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller
2019-05-07 13:51 ` Simon Horman
@ 2019-05-13 12:17 ` Simon Horman
0 siblings, 0 replies; 15+ messages in thread
From: Simon Horman @ 2019-05-13 12:17 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel
On Tue, May 07, 2019 at 03:51:44PM +0200, Simon Horman wrote:
> On Thu, May 02, 2019 at 02:32:16PM +0200, Geert Uytterhoeven wrote:
> > Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
> >
> > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
>
> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
FWIIW, Acceptance/Approval of this patch is blocking me
applying the soc and dt patches of this series.
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller
2019-05-02 12:32 ` [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller Geert Uytterhoeven
2019-05-07 13:51 ` Simon Horman
@ 2019-05-13 17:20 ` Rob Herring
2019-12-11 15:32 ` Geert Uytterhoeven
2 siblings, 0 replies; 15+ messages in thread
From: Rob Herring @ 2019-05-13 17:20 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Mark Rutland,
Simon Horman, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel, Geert Uytterhoeven
On Thu, 2 May 2019 14:32:16 +0200, Geert Uytterhoeven wrote:
> Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> ---
> v3:
> - Use interrupt-map (+ #address-cells and interrupt-map-mask) instead
> of renesas,gic-spi-base,
>
> v2:
> - Add "renesas,gic-spi-base",
> - Document RZ/A2M.
> ---
> .../renesas,rza1-irqc.txt | 43 +++++++++++++++++++
> 1 file changed, 43 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller
2019-05-02 12:32 ` [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller Geert Uytterhoeven
2019-05-07 13:51 ` Simon Horman
2019-05-13 17:20 ` Rob Herring
@ 2019-12-11 15:32 ` Geert Uytterhoeven
2 siblings, 0 replies; 15+ messages in thread
From: Geert Uytterhoeven @ 2019-12-11 15:32 UTC (permalink / raw)
To: Rob Herring
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Mark Rutland,
Simon Horman, Magnus Damm, Chris Brandt,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux-Renesas, Linux Kernel Mailing List, Geert Uytterhoeven
Hi Rob,
On Thu, May 2, 2019 at 2:32 PM Geert Uytterhoeven
<geert+renesas@glider.be> wrote:
> Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt
> @@ -0,0 +1,43 @@
> +DT bindings for the Renesas RZ/A1 Interrupt Controller
> +
> +The RZ/A1 Interrupt Controller is a front-end for the GIC found on Renesas
> +RZ/A1 and RZ/A2 SoCs:
> + - IRQ sense select for 8 external interrupts, 1:1-mapped to 8 GIC SPI
> + interrupts,
> + - NMI edge select.
> +
> +Required properties:
> + - compatible: Must be "renesas,<soctype>-irqc", and "renesas,rza1-irqc" as
> + fallback.
> + Examples with soctypes are:
> + - "renesas,r7s72100-irqc" (RZ/A1H)
> + - "renesas,r7s9210-irqc" (RZ/A2M)
> + - #interrupt-cells: Must be 2 (an interrupt index and flags, as defined
> + in interrupts.txt in this directory)
> + - #address-cells: Must be zero
> + - interrupt-controller: Marks the device as an interrupt controller
> + - reg: Base address and length of the memory resource used by the interrupt
> + controller
> + - interrupt-map: Specifies the mapping from external interrupts to GIC
> + interrupts
> + - interrupt-map-mask: Must be <7 0>
> +
> +Example:
> +
> + irqc: interrupt-controller@fcfef800 {
> + compatible = "renesas,r7s72100-irqc", "renesas,rza1-irqc";
> + #interrupt-cells = <2>;
> + #address-cells = <0>;
> + interrupt-controller;
> + reg = <0xfcfef800 0x6>;
> + interrupt-map =
> + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-map-mask = <7 0>;
> + };
"make dtbs_check" does not like this example:
arch/arm/boot/dts/r7s72100-rskrza1.dt.yaml:
interrupt-controller@fcfef800: {'compatible':
['renesas,r7s72100-irqc', 'renesas,rza1-irqc'], '#interrupt-cells':
[[2]], '#address-cells': [[0]], 'interrupt-controller': True, 'reg':
[[4244568064, 6]], 'interrupt-map': [[0, 0, 3, 0, 0, 4], [1, 0, 3, 0,
1, 4], [2, 0, 3, 0, 2, 4], [3, 0, 3, 0, 3, 4], [4, 0, 3, 0, 4, 4], [5,
0, 3, 0, 5, 4], [6, 0, 3, 0, 6, 4], [7, 0, 3, 0, 7, 4]],
'interrupt-map-mask': [[7, 0]], 'phandle': [[27]], '$nodename':
['interrupt-controller@fcfef800']} is valid under each of {'required':
['interrupt-map']}, {'required': ['interrupt-controller']}
{'oneOf': [{'required': ['interrupt-controller']},
{'required': ['interrupt-map']}]}
as it considers interrupt-controller and interrupt-map mutually-exclusive.
This comes from
dt-schema/meta-schemas/interrupts.yaml:
dependencies:
interrupt-map: ['#interrupt-cells', 'interrupt-map-mask']
'#interrupt-cells':
oneOf:
- required:
- interrupt-controller
- required:
- interrupt-map
and/or dt-schema/schemas/interrupt-controller.yaml:
dependencies:
interrupt-controller: ['#interrupt-cells']
interrupt-map: ['#interrupt-cells', 'interrupt-map-mask']
"#interrupt-cells":
oneOf:
- required:
- interrupt-controller
- required:
- interrupt-map
Removing the "interrupt-controller" property fixes the warning, but
impacts the logic in of_irq_parse_raw().
Is there something wrong with the base schema?
Or perhaps this will just be be fixed by converting renesas,rza1-irqc.txt
to yaml?
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v3 2/5] irqchip: Add Renesas RZ/A1 Interrupt Controller driver
2019-05-02 12:32 [PATCH v3 0/5] ARM: rskrza1: Add RZ/A1 IRQC and input switches Geert Uytterhoeven
2019-05-02 12:32 ` [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller Geert Uytterhoeven
@ 2019-05-02 12:32 ` Geert Uytterhoeven
2019-05-07 13:53 ` Simon Horman
2019-05-02 12:32 ` [PATCH v3 3/5] soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M Geert Uytterhoeven
` (2 subsequent siblings)
4 siblings, 1 reply; 15+ messages in thread
From: Geert Uytterhoeven @ 2019-05-02 12:32 UTC (permalink / raw)
To: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Simon Horman, Magnus Damm, Chris Brandt
Cc: devicetree, linux-renesas-soc, linux-kernel, Geert Uytterhoeven
Add a driver for the Renesas RZ/A1 Interrupt Controller.
This supports using up to 8 external interrupts on RZ/A1, with
configurable sense select.
NMI edge select is not yet supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
---
For simplicity, interrupt-map-mask is not parsed, but ignored.
I also considered extracting the parsing code in of_irq_parse_raw() in a
new public helper function:
int of_irq_parse_map(struct device_node **ipar, u32 *addrsize,
u32 *intsize, const __be32 **match_array,
struct of_phandle_args *out_irq);
However, that API is a bit ugly due to many output parameters
(of_irq_parse_raw() needs to iterate the interrupt hierarchy).
In addition, it's less efficient for irq-renesas-rza1.c, as the
interrupt-map must be parsed 8 times.
v3:
- Add Tested-by,
- Replace renesas,gic-spi-base in DT by interrupt-map in DT,
v2:
- Use u16 for register values,
- Use relaxed I/O accessors,
- Use "rza1-irqc" as irq_chip class name,
- Replace gic_spi_base in OF match data by renesas,gic-spi-base in DT.
---
drivers/irqchip/Kconfig | 4 +
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-renesas-rza1.c | 283 +++++++++++++++++++++++++++++
3 files changed, 288 insertions(+)
create mode 100644 drivers/irqchip/irq-renesas-rza1.c
diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index 8c1c67f9a4bb5bf6..db07db4c48486649 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -224,6 +224,10 @@ config RENESAS_IRQC
select GENERIC_IRQ_CHIP
select IRQ_DOMAIN
+config RENESAS_RZA1_IRQC
+ bool
+ select IRQ_DOMAIN_HIERARCHY
+
config ST_IRQCHIP
bool
select REGMAP
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index f8c66e958a64deaa..ce37fba74effad8c 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_JCORE_AIC) += irq-jcore-aic.o
obj-$(CONFIG_RDA_INTC) += irq-rda-intc.o
obj-$(CONFIG_RENESAS_INTC_IRQPIN) += irq-renesas-intc-irqpin.o
obj-$(CONFIG_RENESAS_IRQC) += irq-renesas-irqc.o
+obj-$(CONFIG_RENESAS_RZA1_IRQC) += irq-renesas-rza1.o
obj-$(CONFIG_VERSATILE_FPGA_IRQ) += irq-versatile-fpga.o
obj-$(CONFIG_ARCH_NSPIRE) += irq-zevio.o
obj-$(CONFIG_ARCH_VT8500) += irq-vt8500.o
diff --git a/drivers/irqchip/irq-renesas-rza1.c b/drivers/irqchip/irq-renesas-rza1.c
new file mode 100644
index 0000000000000000..b1f19b210190184f
--- /dev/null
+++ b/drivers/irqchip/irq-renesas-rza1.c
@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Renesas RZ/A1 IRQC Driver
+ *
+ * Copyright (C) 2019 Glider bvba
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#define IRQC_NUM_IRQ 8
+
+#define ICR0 0 /* Interrupt Control Register 0 */
+
+#define ICR0_NMIL BIT(15) /* NMI Input Level (0=low, 1=high) */
+#define ICR0_NMIE BIT(8) /* Edge Select (0=falling, 1=rising) */
+#define ICR0_NMIF BIT(1) /* NMI Interrupt Request */
+
+#define ICR1 2 /* Interrupt Control Register 1 */
+
+#define ICR1_IRQS(n, sense) ((sense) << ((n) * 2)) /* IRQ Sense Select */
+#define ICR1_IRQS_LEVEL_LOW 0
+#define ICR1_IRQS_EDGE_FALLING 1
+#define ICR1_IRQS_EDGE_RISING 2
+#define ICR1_IRQS_EDGE_BOTH 3
+#define ICR1_IRQS_MASK(n) ICR1_IRQS((n), 3)
+
+#define IRQRR 4 /* IRQ Interrupt Request Register */
+
+
+struct rza1_irqc_priv {
+ struct device *dev;
+ void __iomem *base;
+ struct irq_chip chip;
+ struct irq_domain *irq_domain;
+ struct of_phandle_args map[IRQC_NUM_IRQ];
+};
+
+static struct rza1_irqc_priv *irq_data_to_priv(struct irq_data *data)
+{
+ return data->domain->host_data;
+}
+
+static void rza1_irqc_eoi(struct irq_data *d)
+{
+ struct rza1_irqc_priv *priv = irq_data_to_priv(d);
+ u16 bit = BIT(irqd_to_hwirq(d));
+ u16 tmp;
+
+ tmp = readw_relaxed(priv->base + IRQRR);
+ if (tmp & bit)
+ writew_relaxed(GENMASK(IRQC_NUM_IRQ - 1, 0) & ~bit,
+ priv->base + IRQRR);
+
+ irq_chip_eoi_parent(d);
+}
+
+static int rza1_irqc_set_type(struct irq_data *d, unsigned int type)
+{
+ struct rza1_irqc_priv *priv = irq_data_to_priv(d);
+ unsigned int hw_irq = irqd_to_hwirq(d);
+ u16 sense, tmp;
+
+ switch (type & IRQ_TYPE_SENSE_MASK) {
+ case IRQ_TYPE_LEVEL_LOW:
+ sense = ICR1_IRQS_LEVEL_LOW;
+ break;
+
+ case IRQ_TYPE_EDGE_FALLING:
+ sense = ICR1_IRQS_EDGE_FALLING;
+ break;
+
+ case IRQ_TYPE_EDGE_RISING:
+ sense = ICR1_IRQS_EDGE_RISING;
+ break;
+
+ case IRQ_TYPE_EDGE_BOTH:
+ sense = ICR1_IRQS_EDGE_BOTH;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ tmp = readw_relaxed(priv->base + ICR1);
+ tmp &= ~ICR1_IRQS_MASK(hw_irq);
+ tmp |= ICR1_IRQS(hw_irq, sense);
+ writew_relaxed(tmp, priv->base + ICR1);
+ return 0;
+}
+
+static int rza1_irqc_alloc(struct irq_domain *domain, unsigned int virq,
+ unsigned int nr_irqs, void *arg)
+{
+ struct rza1_irqc_priv *priv = domain->host_data;
+ struct irq_fwspec *fwspec = arg;
+ unsigned int hwirq = fwspec->param[0];
+ struct irq_fwspec spec;
+ unsigned int i;
+ int ret;
+
+ ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq, &priv->chip,
+ priv);
+ if (ret)
+ return ret;
+
+ spec.fwnode = &priv->dev->of_node->fwnode;
+ spec.param_count = priv->map[hwirq].args_count;
+ for (i = 0; i < spec.param_count; i++)
+ spec.param[i] = priv->map[hwirq].args[i];
+
+ return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, &spec);
+}
+
+static int rza1_irqc_translate(struct irq_domain *domain,
+ struct irq_fwspec *fwspec, unsigned long *hwirq,
+ unsigned int *type)
+{
+ if (fwspec->param_count != 2 || fwspec->param[0] >= IRQC_NUM_IRQ)
+ return -EINVAL;
+
+ *hwirq = fwspec->param[0];
+ *type = fwspec->param[1];
+ return 0;
+}
+
+static const struct irq_domain_ops rza1_irqc_domain_ops = {
+ .alloc = rza1_irqc_alloc,
+ .translate = rza1_irqc_translate,
+};
+
+static int rza1_irqc_parse_map(struct rza1_irqc_priv *priv,
+ struct device_node *gic_node)
+{
+ unsigned int imaplen, i, j, ret;
+ struct device *dev = priv->dev;
+ struct device_node *ipar;
+ const __be32 *imap;
+ u32 intsize;
+
+ imap = of_get_property(dev->of_node, "interrupt-map", &imaplen);
+ if (!imap)
+ return -EINVAL;
+
+ for (i = 0; i < IRQC_NUM_IRQ; i++) {
+ if (imaplen < 3)
+ return -EINVAL;
+
+ /* Check interrupt number, ignore sense */
+ if (be32_to_cpup(imap) != i)
+ return -EINVAL;
+
+ ipar = of_find_node_by_phandle(be32_to_cpup(imap + 2));
+ if (ipar != gic_node) {
+ of_node_put(ipar);
+ return -EINVAL;
+ }
+
+ imap += 3;
+ imaplen -= 3;
+
+ ret = of_property_read_u32(ipar, "#interrupt-cells", &intsize);
+ of_node_put(ipar);
+ if (ret)
+ return ret;
+
+ if (imaplen < intsize)
+ return -EINVAL;
+
+ priv->map[i].args_count = intsize;
+ for (j = 0; j < intsize; j++)
+ priv->map[i].args[j] = be32_to_cpup(imap++);
+
+ imaplen -= intsize;
+ }
+
+ return 0;
+}
+
+static int rza1_irqc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct irq_domain *parent = NULL;
+ struct device_node *gic_node;
+ struct rza1_irqc_priv *priv;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, priv);
+ priv->dev = dev;
+
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ gic_node = of_irq_find_parent(np);
+ if (gic_node) {
+ parent = irq_find_host(gic_node);
+ of_node_put(gic_node);
+ }
+
+ if (!parent) {
+ dev_err(dev, "cannot find parent domain\n");
+ return -ENODEV;
+ }
+
+ ret = rza1_irqc_parse_map(priv, gic_node);
+ if (ret) {
+ dev_err(dev, "cannot parse %s: %d\n", "interrupt-map", ret);
+ return ret;
+ }
+
+ priv->chip.name = "rza1-irqc",
+ priv->chip.irq_mask = irq_chip_mask_parent,
+ priv->chip.irq_unmask = irq_chip_unmask_parent,
+ priv->chip.irq_eoi = rza1_irqc_eoi,
+ priv->chip.irq_retrigger = irq_chip_retrigger_hierarchy,
+ priv->chip.irq_set_type = rza1_irqc_set_type,
+ priv->chip.flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE;
+
+ priv->irq_domain = irq_domain_add_hierarchy(parent, 0, IRQC_NUM_IRQ,
+ np, &rza1_irqc_domain_ops,
+ priv);
+ if (!priv->irq_domain) {
+ dev_err(dev, "cannot initialize irq domain\n");
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int rza1_irqc_remove(struct platform_device *pdev)
+{
+ struct rza1_irqc_priv *priv = platform_get_drvdata(pdev);
+
+ irq_domain_remove(priv->irq_domain);
+ return 0;
+}
+
+static const struct of_device_id rza1_irqc_dt_ids[] = {
+ { .compatible = "renesas,rza1-irqc" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, rza1_irqc_dt_ids);
+
+static struct platform_driver rza1_irqc_device_driver = {
+ .probe = rza1_irqc_probe,
+ .remove = rza1_irqc_remove,
+ .driver = {
+ .name = "renesas_rza1_irqc",
+ .of_match_table = rza1_irqc_dt_ids,
+ }
+};
+
+static int __init rza1_irqc_init(void)
+{
+ return platform_driver_register(&rza1_irqc_device_driver);
+}
+postcore_initcall(rza1_irqc_init);
+
+static void __exit rza1_irqc_exit(void)
+{
+ platform_driver_unregister(&rza1_irqc_device_driver);
+}
+module_exit(rza1_irqc_exit);
+
+MODULE_AUTHOR("Geert Uytterhoeven <geert+renesas@glider.be>");
+MODULE_DESCRIPTION("Renesas RZ/A1 IRQC Driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v3 2/5] irqchip: Add Renesas RZ/A1 Interrupt Controller driver
2019-05-02 12:32 ` [PATCH v3 2/5] irqchip: Add Renesas RZ/A1 Interrupt Controller driver Geert Uytterhoeven
@ 2019-05-07 13:53 ` Simon Horman
0 siblings, 0 replies; 15+ messages in thread
From: Simon Horman @ 2019-05-07 13:53 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel
On Thu, May 02, 2019 at 02:32:17PM +0200, Geert Uytterhoeven wrote:
> Add a driver for the Renesas RZ/A1 Interrupt Controller.
>
> This supports using up to 8 external interrupts on RZ/A1, with
> configurable sense select.
>
> NMI edge select is not yet supported.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Tested-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v3 3/5] soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
2019-05-02 12:32 [PATCH v3 0/5] ARM: rskrza1: Add RZ/A1 IRQC and input switches Geert Uytterhoeven
2019-05-02 12:32 ` [PATCH v3 1/5] dt-bindings: interrupt-controller: Add Renesas RZ/A1 Interrupt Controller Geert Uytterhoeven
2019-05-02 12:32 ` [PATCH v3 2/5] irqchip: Add Renesas RZ/A1 Interrupt Controller driver Geert Uytterhoeven
@ 2019-05-02 12:32 ` Geert Uytterhoeven
2019-06-06 8:37 ` Simon Horman
2019-05-02 12:32 ` [PATCH v3 4/5] ARM: dts: r7s72100: Add IRQC device node Geert Uytterhoeven
2019-05-02 12:32 ` [PATCH v3 5/5] ARM: dts: rskrza1: Add input switches Geert Uytterhoeven
4 siblings, 1 reply; 15+ messages in thread
From: Geert Uytterhoeven @ 2019-05-02 12:32 UTC (permalink / raw)
To: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Simon Horman, Magnus Damm, Chris Brandt
Cc: devicetree, linux-renesas-soc, linux-kernel, Geert Uytterhoeven
Auto-enable support for the RZ/A1 Interrupt Controller when configuring
a kernel which supports RZ/A1H or RZ/A2M SoCs.
Keep selects sorted while at it.
This is similar to how interrupt controllers for other Renesas SoCs are
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
---
v3:
- No changes,
v2:
- Add Reviewed-by,
- Add RZ/A2M,
- Sort RZ/A1H selects.
---
drivers/soc/renesas/Kconfig | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/soc/renesas/Kconfig b/drivers/soc/renesas/Kconfig
index 68bfca6f20ddf8a7..2bbf49e5d441808b 100644
--- a/drivers/soc/renesas/Kconfig
+++ b/drivers/soc/renesas/Kconfig
@@ -57,14 +57,16 @@ config ARCH_R7S72100
bool "RZ/A1H (R7S72100)"
select PM
select PM_GENERIC_DOMAINS
- select SYS_SUPPORTS_SH_MTU2
select RENESAS_OSTM
+ select RENESAS_RZA1_IRQC
+ select SYS_SUPPORTS_SH_MTU2
config ARCH_R7S9210
bool "RZ/A2 (R7S9210)"
select PM
select PM_GENERIC_DOMAINS
select RENESAS_OSTM
+ select RENESAS_RZA1_IRQC
config ARCH_R8A73A4
bool "R-Mobile APE6 (R8A73A40)"
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v3 3/5] soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M
2019-05-02 12:32 ` [PATCH v3 3/5] soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M Geert Uytterhoeven
@ 2019-06-06 8:37 ` Simon Horman
0 siblings, 0 replies; 15+ messages in thread
From: Simon Horman @ 2019-06-06 8:37 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel
On Thu, May 02, 2019 at 02:32:18PM +0200, Geert Uytterhoeven wrote:
> Auto-enable support for the RZ/A1 Interrupt Controller when configuring
> a kernel which supports RZ/A1H or RZ/A2M SoCs.
> Keep selects sorted while at it.
>
> This is similar to how interrupt controllers for other Renesas SoCs are
> enabled.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Thanks, applied for v5.3.
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v3 4/5] ARM: dts: r7s72100: Add IRQC device node
2019-05-02 12:32 [PATCH v3 0/5] ARM: rskrza1: Add RZ/A1 IRQC and input switches Geert Uytterhoeven
` (2 preceding siblings ...)
2019-05-02 12:32 ` [PATCH v3 3/5] soc: renesas: Enable RZ/A1 IRQC on RZ/A1H and RZ/A2M Geert Uytterhoeven
@ 2019-05-02 12:32 ` Geert Uytterhoeven
2019-05-20 11:27 ` Simon Horman
2019-05-02 12:32 ` [PATCH v3 5/5] ARM: dts: rskrza1: Add input switches Geert Uytterhoeven
4 siblings, 1 reply; 15+ messages in thread
From: Geert Uytterhoeven @ 2019-05-02 12:32 UTC (permalink / raw)
To: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Simon Horman, Magnus Damm, Chris Brandt
Cc: devicetree, linux-renesas-soc, linux-kernel, Geert Uytterhoeven
Enable support for the IRQC on RZ/A1H, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
---
v3:
- Use interrupt-map (+ #address-cells and interrupt-map-mask) instead
of renesas,gic-spi-base,
v2:
- Add Reviewed-by,
- Add "renesas,gic-spi-base".
---
arch/arm/boot/dts/r7s72100.dtsi | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index 2211f88ede2ad351..d03dcd919d6f5cfb 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -670,6 +670,25 @@
status = "disabled";
};
+ irqc: interrupt-controller@fcfef800 {
+ compatible = "renesas,r7s72100-irqc",
+ "renesas,rza1-irqc";
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0xfcfef800 0x6>;
+ interrupt-map =
+ <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+ <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+ <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+ <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+ <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-map-mask = <7 0>;
+ };
+
mtu2: timer@fcff0000 {
compatible = "renesas,mtu2-r7s72100", "renesas,mtu2";
reg = <0xfcff0000 0x400>;
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v3 4/5] ARM: dts: r7s72100: Add IRQC device node
2019-05-02 12:32 ` [PATCH v3 4/5] ARM: dts: r7s72100: Add IRQC device node Geert Uytterhoeven
@ 2019-05-20 11:27 ` Simon Horman
0 siblings, 0 replies; 15+ messages in thread
From: Simon Horman @ 2019-05-20 11:27 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel
On Thu, May 02, 2019 at 02:32:19PM +0200, Geert Uytterhoeven wrote:
> Enable support for the IRQC on RZ/A1H, which is a small front-end to the
> GIC. This allows to use up to 8 external interrupts with configurable
> sense select.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
> Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Thanks Geert,
I have applied this for inclusion in v5.3
^ permalink raw reply [flat|nested] 15+ messages in thread
* [PATCH v3 5/5] ARM: dts: rskrza1: Add input switches
2019-05-02 12:32 [PATCH v3 0/5] ARM: rskrza1: Add RZ/A1 IRQC and input switches Geert Uytterhoeven
` (3 preceding siblings ...)
2019-05-02 12:32 ` [PATCH v3 4/5] ARM: dts: r7s72100: Add IRQC device node Geert Uytterhoeven
@ 2019-05-02 12:32 ` Geert Uytterhoeven
2019-05-20 11:29 ` Simon Horman
4 siblings, 1 reply; 15+ messages in thread
From: Geert Uytterhoeven @ 2019-05-02 12:32 UTC (permalink / raw)
To: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Simon Horman, Magnus Damm, Chris Brandt
Cc: devicetree, linux-renesas-soc, linux-kernel, Geert Uytterhoeven
Add support for input switches SW1-3 on the Renesas RZ/A1 RSK+RZA1
development board.
Note that this uses the IRQ interrupts, as the RZ/A1 GPIO controller
does not include interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
v3:
- No changes,
v2:
- No changes,
v1:
- Use rza1-irqc instead of gic.
v0:
- Sent as an RFC in a reply to another thread.
---
arch/arm/boot/dts/r7s72100-rskrza1.dts | 38 ++++++++++++++++++++++++++
1 file changed, 38 insertions(+)
diff --git a/arch/arm/boot/dts/r7s72100-rskrza1.dts b/arch/arm/boot/dts/r7s72100-rskrza1.dts
index ff24301dc1be54de..99acfe4fe11aaed9 100644
--- a/arch/arm/boot/dts/r7s72100-rskrza1.dts
+++ b/arch/arm/boot/dts/r7s72100-rskrza1.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "r7s72100.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/r7s72100-pinctrl.h>
/ {
@@ -28,6 +29,37 @@
reg = <0x08000000 0x02000000>;
};
+ keyboard {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&keyboard_pins>;
+
+ key-1 {
+ interrupt-parent = <&irqc>;
+ interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_1>;
+ label = "SW1";
+ wakeup-source;
+ };
+
+ key-2 {
+ interrupt-parent = <&irqc>;
+ interrupts = <2 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_2>;
+ label = "SW2";
+ wakeup-source;
+ };
+
+ key-3 {
+ interrupt-parent = <&irqc>;
+ interrupts = <5 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_3>;
+ label = "SW3";
+ wakeup-source;
+ };
+ };
+
lbsc {
#address-cells = <1>;
#size-cells = <1>;
@@ -101,6 +133,12 @@
<RZA1_PINMUX(1, 7, 1)>; /* RIIC3SDA */
};
+ keyboard_pins: keyboard {
+ pinmux = <RZA1_PINMUX(1, 9, 3)>, /* IRQ3 */
+ <RZA1_PINMUX(1, 8, 3)>, /* IRQ2 */
+ <RZA1_PINMUX(1, 11, 3)>; /* IRQ5 */
+ };
+
/* Serial Console */
scif2_pins: serial2 {
pinmux = <RZA1_PINMUX(3, 0, 6)>, /* TxD2 */
--
2.17.1
^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [PATCH v3 5/5] ARM: dts: rskrza1: Add input switches
2019-05-02 12:32 ` [PATCH v3 5/5] ARM: dts: rskrza1: Add input switches Geert Uytterhoeven
@ 2019-05-20 11:29 ` Simon Horman
0 siblings, 0 replies; 15+ messages in thread
From: Simon Horman @ 2019-05-20 11:29 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Thomas Gleixner, Jason Cooper, Marc Zyngier, Rob Herring,
Mark Rutland, Magnus Damm, Chris Brandt, devicetree,
linux-renesas-soc, linux-kernel
On Thu, May 02, 2019 at 02:32:20PM +0200, Geert Uytterhoeven wrote:
> Add support for input switches SW1-3 on the Renesas RZ/A1 RSK+RZA1
> development board.
>
> Note that this uses the IRQ interrupts, as the RZ/A1 GPIO controller
> does not include interrupt support.
>
> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Thanks Geert,
I have applied this for inclusion in v5.3
^ permalink raw reply [flat|nested] 15+ messages in thread