[PATCH AUTOSEL 4.19 001/158] wil6210: fix potential out-of-bounds read

[PATCH AUTOSEL 4.19 001/158] wil6210: fix potential out-of-bounds read

[Sasha Levin]

From: "Gustavo A. R. Silva" <gustavo@embeddedor.com>

[ Upstream commit bfabdd6997323adbedccb13a3fed1967fb8cf8f5 ]

Notice that *rc* can evaluate to up to 5, include/linux/netdevice.h:

enum gro_result {
        GRO_MERGED,
        GRO_MERGED_FREE,
        GRO_HELD,
        GRO_NORMAL,
        GRO_DROP,
        GRO_CONSUMED,
};
typedef enum gro_result gro_result_t;

In case *rc* evaluates to 5, we end up having an out-of-bounds read
at drivers/net/wireless/ath/wil6210/txrx.c:821:

	wil_dbg_txrx(wil, "Rx complete %d bytes => %s\n",
		     len, gro_res_str[rc]);

Fix this by adding element "GRO_CONSUMED" to array gro_res_str.

Addresses-Coverity-ID: 1444666 ("Out-of-bounds read")
Fixes: 194b482b5055 ("wil6210: Debug print GRO Rx result")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/wil6210/txrx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index 75c8aa297107..1b1b58e0129a 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -736,6 +736,7 @@ void wil_netif_rx_any(struct sk_buff *skb, struct net_device *ndev)
 		[GRO_HELD]		= "GRO_HELD",
 		[GRO_NORMAL]		= "GRO_NORMAL",
 		[GRO_DROP]		= "GRO_DROP",
+		[GRO_CONSUMED]		= "GRO_CONSUMED",
 	};
 
 	wil->txrx_ops.get_netif_rx_params(skb, &cid, &security);
-- 
2.20.1

[PATCH AUTOSEL 4.19 002/158] ath10k: Do not send probe response template for mesh

[Sasha Levin]

From: Surabhi Vishnoi <svishnoi@codeaurora.org>

[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]

Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.

To avoid this failure, skip sending probe response template to
firmware for mesh point.

Tested HW: WCN3990/QCA6174/QCA9984

Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index f3b1cfacfe9d..1419f9d1505f 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -1624,6 +1624,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
 	if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
 		return 0;
 
+	 /* For mesh, probe response and beacon share the same template */
+	if (ieee80211_vif_is_mesh(vif))
+		return 0;
+
 	prb = ieee80211_proberesp_get(hw, vif);
 	if (!prb) {
 		ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
-- 
2.20.1

[PATCH AUTOSEL 4.19 003/158] ath9k: Check for errors when reading SREV register

[Sasha Levin]

From: Tim Schumacher <timschumi@gmx.de>

[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]

Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Failed to read SREV register
    ath: phy2: Could not read hardware revision
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.

Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index bb319f22761f..b4f7ee423d40 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -252,8 +252,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,
 /* Chip Revisions */
 /******************/
 
-static void ath9k_hw_read_revisions(struct ath_hw *ah)
+static bool ath9k_hw_read_revisions(struct ath_hw *ah)
 {
+	u32 srev;
 	u32 val;
 
 	if (ah->get_mac_revision)
@@ -269,25 +270,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 			val = REG_READ(ah, AR_SREV);
 			ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
 		}
-		return;
+		return true;
 	case AR9300_DEVID_AR9340:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9340;
-		return;
+		return true;
 	case AR9300_DEVID_QCA955X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9550;
-		return;
+		return true;
 	case AR9300_DEVID_AR953X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9531;
-		return;
+		return true;
 	case AR9300_DEVID_QCA956X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9561;
-		return;
+		return true;
 	}
 
-	val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+	srev = REG_READ(ah, AR_SREV);
+
+	if (srev == -EIO) {
+		ath_err(ath9k_hw_common(ah),
+			"Failed to read SREV register");
+		return false;
+	}
+
+	val = srev & AR_SREV_ID;
 
 	if (val == 0xFF) {
-		val = REG_READ(ah, AR_SREV);
+		val = srev;
 		ah->hw_version.macVersion =
 			(val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
 		ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
@@ -306,6 +315,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 		if (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE)
 			ah->is_pciexpress = true;
 	}
+
+	return true;
 }
 
 /************************************/
@@ -559,7 +570,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)
 	struct ath_common *common = ath9k_hw_common(ah);
 	int r = 0;
 
-	ath9k_hw_read_revisions(ah);
+	if (!ath9k_hw_read_revisions(ah)) {
+		ath_err(common, "Could not read hardware revisions");
+		return -EOPNOTSUPP;
+	}
 
 	switch (ah->hw_version.macVersion) {
 	case AR_SREV_VERSION_5416_PCI:
-- 
2.20.1

[PATCH AUTOSEL 4.19 004/158] ath6kl: add some bounds checking

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ]

The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements.  We need to add a couple bounds
checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes: bdcd81707973 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath6kl/wmi.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath6kl/wmi.c b/drivers/net/wireless/ath/ath6kl/wmi.c
index 777acc564ac9..bc7916f2add0 100644
--- a/drivers/net/wireless/ath/ath6kl/wmi.c
+++ b/drivers/net/wireless/ath/ath6kl/wmi.c
@@ -1178,6 +1178,10 @@ static int ath6kl_wmi_pstream_timeout_event_rx(struct wmi *wmi, u8 *datap,
 		return -EINVAL;
 
 	ev = (struct wmi_pstream_timeout_event *) datap;
+	if (ev->traffic_class >= WMM_NUM_AC) {
+		ath6kl_err("invalid traffic class: %d\n", ev->traffic_class);
+		return -EINVAL;
+	}
 
 	/*
 	 * When the pstream (fat pipe == AC) timesout, it means there were
@@ -1519,6 +1523,10 @@ static int ath6kl_wmi_cac_event_rx(struct wmi *wmi, u8 *datap, int len,
 		return -EINVAL;
 
 	reply = (struct wmi_cac_event *) datap;
+	if (reply->ac >= WMM_NUM_AC) {
+		ath6kl_err("invalid AC: %d\n", reply->ac);
+		return -EINVAL;
+	}
 
 	if ((reply->cac_indication == CAC_INDICATION_ADMISSION_RESP) &&
 	    (reply->status_code != IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED)) {
@@ -2635,7 +2643,7 @@ int ath6kl_wmi_delete_pstream_cmd(struct wmi *wmi, u8 if_idx, u8 traffic_class,
 	u16 active_tsids = 0;
 	int ret;
 
-	if (traffic_class > 3) {
+	if (traffic_class >= WMM_NUM_AC) {
 		ath6kl_err("invalid traffic class: %d\n", traffic_class);
 		return -EINVAL;
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.19 005/158] ath10k: add peer id check in ath10k_peer_find_by_id

[Sasha Levin]

From: Wen Gong <wgong@codeaurora.org>

[ Upstream commit 49ed34b835e231aa941257394716bc689bc98d9f ]

For some SDIO chip, the peer id is 65535 for MPDU with error status,
then test_bit will trigger buffer overflow for peer's memory, if kasan
enabled, it will report error.

Reason is when station is in disconnecting status, firmware do not delete
the peer info since it not disconnected completely, meanwhile some AP will
still send data packet to station, then hardware will receive the packet
and send to firmware, firmware's logic will report peer id of 65535 for
MPDU with error status.

Add check for overflow the size of peer's peer_ids will avoid the buffer
overflow access.

Call trace of kasan:
dump_backtrace+0x0/0x2ec
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x250/0x26c
__asan_report_load8_noabort+0x20/0x2c
ath10k_peer_find_by_id+0x180/0x1e4 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x100c/0x2fd4 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x34 [ath10k_core]
ath10k_sdio_irq_handler+0xcc8/0x1678 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x370
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x508/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/txrx.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/txrx.c b/drivers/net/wireless/ath/ath10k/txrx.c
index cda164f6e9f6..6f62ddc0494c 100644
--- a/drivers/net/wireless/ath/ath10k/txrx.c
+++ b/drivers/net/wireless/ath/ath10k/txrx.c
@@ -156,6 +156,9 @@ struct ath10k_peer *ath10k_peer_find_by_id(struct ath10k *ar, int peer_id)
 {
 	struct ath10k_peer *peer;
 
+	if (peer_id >= BITS_PER_TYPE(peer->peer_ids))
+		return NULL;
+
 	lockdep_assert_held(&ar->data_lock);
 
 	list_for_each_entry(peer, &ar->peers, list)
-- 
2.20.1

[PATCH AUTOSEL 4.19 006/158] x86/tsc: Use CPUID.0x16 to calculate missing crystal frequency

[Sasha Levin]

From: Daniel Drake <drake@endlessm.com>

[ Upstream commit 604dc9170f2435d27da5039a3efd757dceadc684 ]

native_calibrate_tsc() had a data mapping Intel CPU families
and crystal clock speed, but hardcoded tables are not ideal, and this
approach was already problematic at least in the Skylake X case, as
seen in commit:

  b51120309348 ("x86/tsc: Fix erroneous TSC rate on Skylake Xeon")

By examining CPUID data from http://instlatx64.atw.hu/ and units
in the lab, we have found that 3 different scenarios need to be dealt
with, and we can eliminate most of the hardcoded data using an approach a
little more advanced than before:

 1. ApolloLake, GeminiLake, CannonLake (and presumably all new chipsets
    from this point) report the crystal frequency directly via CPUID.0x15.
    That's definitive data that we can rely upon.

 2. Skylake, Kabylake and all variants of those two chipsets report a
    crystal frequency of zero, however we can calculate the crystal clock
    speed by condidering data from CPUID.0x16.

    This method correctly distinguishes between the two crystal clock
    frequencies present on different Skylake X variants that caused
    headaches before.

    As the calculations do not quite match the previously-hardcoded values
    in some cases (e.g. 23913043Hz instead of 24MHz), TSC refinement is
    enabled on all platforms where we had to calculate the crystal
    frequency in this way.

 3. Denverton (GOLDMONT_X) reports a crystal frequency of zero and does
    not support CPUID.0x16, so we leave this entry hardcoded.

Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: len.brown@intel.com
Cc: linux@endlessm.com
Cc: rafael.j.wysocki@intel.com
Link: http://lkml.kernel.org/r/20190509055417.13152-1-drake@endlessm.com
Link: https://lkml.kernel.org/r/20190419083533.32388-1-drake@endlessm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/tsc.c | 47 +++++++++++++++++++++++++------------------
 1 file changed, 27 insertions(+), 20 deletions(-)

diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c
index 03b7529333a6..58a4ac0d20a8 100644
--- a/arch/x86/kernel/tsc.c
+++ b/arch/x86/kernel/tsc.c
@@ -628,31 +628,38 @@ unsigned long native_calibrate_tsc(void)
 
 	crystal_khz = ecx_hz / 1000;
 
-	if (crystal_khz == 0) {
-		switch (boot_cpu_data.x86_model) {
-		case INTEL_FAM6_SKYLAKE_MOBILE:
-		case INTEL_FAM6_SKYLAKE_DESKTOP:
-		case INTEL_FAM6_KABYLAKE_MOBILE:
-		case INTEL_FAM6_KABYLAKE_DESKTOP:
-			crystal_khz = 24000;	/* 24.0 MHz */
-			break;
-		case INTEL_FAM6_ATOM_GOLDMONT_X:
-			crystal_khz = 25000;	/* 25.0 MHz */
-			break;
-		case INTEL_FAM6_ATOM_GOLDMONT:
-			crystal_khz = 19200;	/* 19.2 MHz */
-			break;
-		}
-	}
+	/*
+	 * Denverton SoCs don't report crystal clock, and also don't support
+	 * CPUID.0x16 for the calculation below, so hardcode the 25MHz crystal
+	 * clock.
+	 */
+	if (crystal_khz == 0 &&
+			boot_cpu_data.x86_model == INTEL_FAM6_ATOM_GOLDMONT_X)
+		crystal_khz = 25000;
 
-	if (crystal_khz == 0)
-		return 0;
 	/*
-	 * TSC frequency determined by CPUID is a "hardware reported"
+	 * TSC frequency reported directly by CPUID is a "hardware reported"
 	 * frequency and is the most accurate one so far we have. This
 	 * is considered a known frequency.
 	 */
-	setup_force_cpu_cap(X86_FEATURE_TSC_KNOWN_FREQ);
+	if (crystal_khz != 0)
+		setup_force_cpu_cap(X86_FEATURE_TSC_KNOWN_FREQ);
+
+	/*
+	 * Some Intel SoCs like Skylake and Kabylake don't report the crystal
+	 * clock, but we can easily calculate it to a high degree of accuracy
+	 * by considering the crystal ratio and the CPU speed.
+	 */
+	if (crystal_khz == 0 && boot_cpu_data.cpuid_level >= 0x16) {
+		unsigned int eax_base_mhz, ebx, ecx, edx;
+
+		cpuid(0x16, &eax_base_mhz, &ebx, &ecx, &edx);
+		crystal_khz = eax_base_mhz * 1000 *
+			eax_denominator / ebx_numerator;
+	}
+
+	if (crystal_khz == 0)
+		return 0;
 
 	/*
 	 * For Atom SoCs TSC is the only reliable clocksource.
-- 
2.20.1

[PATCH AUTOSEL 4.19 007/158] wil6210: fix spurious interrupts in 3-msi

[Sasha Levin]

From: Maya Erez <merez@codeaurora.org>

[ Upstream commit e10b0eddd5235aa5aef4e40b970e34e735611a80 ]

Interrupt is set in ICM (ICR & ~IMV) rising trigger.
As the driver masks the IRQ after clearing it, there can
be a race where an additional spurious interrupt is triggered
when the driver unmask the IRQ.
This can happen in case HW triggers an interrupt after the clear
and before the mask.

To prevent the second spurious interrupt the driver needs to mask the
IRQ before reading and clearing it.

Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/wil6210/interrupt.c | 65 ++++++++++++--------
 1 file changed, 40 insertions(+), 25 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/interrupt.c b/drivers/net/wireless/ath/wil6210/interrupt.c
index 5d287a8e1b45..0655cd884514 100644
--- a/drivers/net/wireless/ath/wil6210/interrupt.c
+++ b/drivers/net/wireless/ath/wil6210/interrupt.c
@@ -296,21 +296,24 @@ void wil_configure_interrupt_moderation(struct wil6210_priv *wil)
 static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_DMA_EP_RX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_rx(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_DMA_EP_RX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_rx(isr);
 	wil_dbg_irq(wil, "ISR RX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err_ratelimited(wil, "spurious IRQ: RX\n");
+		wil6210_unmask_irq_rx(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_rx(wil);
-
 	/* RX_DONE and RX_HTRSH interrupts are the same if interrupt
 	 * moderation is not used. Interrupt moderation may cause RX
 	 * buffer overflow while RX_DONE is delayed. The required
@@ -355,21 +358,24 @@ static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
 static irqreturn_t wil6210_irq_rx_edma(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_INT_GEN_RX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_rx_edma(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_INT_GEN_RX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_rx(isr);
 	wil_dbg_irq(wil, "ISR RX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err(wil, "spurious IRQ: RX\n");
+		wil6210_unmask_irq_rx_edma(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_rx_edma(wil);
-
 	if (likely(isr & BIT_RX_STATUS_IRQ)) {
 		wil_dbg_irq(wil, "RX status ring\n");
 		isr &= ~BIT_RX_STATUS_IRQ;
@@ -403,21 +409,24 @@ static irqreturn_t wil6210_irq_rx_edma(int irq, void *cookie)
 static irqreturn_t wil6210_irq_tx_edma(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_INT_GEN_TX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_tx_edma(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_INT_GEN_TX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_tx(isr);
 	wil_dbg_irq(wil, "ISR TX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err(wil, "spurious IRQ: TX\n");
+		wil6210_unmask_irq_tx_edma(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_tx_edma(wil);
-
 	if (likely(isr & BIT_TX_STATUS_IRQ)) {
 		wil_dbg_irq(wil, "TX status ring\n");
 		isr &= ~BIT_TX_STATUS_IRQ;
@@ -446,21 +455,24 @@ static irqreturn_t wil6210_irq_tx_edma(int irq, void *cookie)
 static irqreturn_t wil6210_irq_tx(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_DMA_EP_TX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_tx(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_DMA_EP_TX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_tx(isr);
 	wil_dbg_irq(wil, "ISR TX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err_ratelimited(wil, "spurious IRQ: TX\n");
+		wil6210_unmask_irq_tx(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_tx(wil);
-
 	if (likely(isr & BIT_DMA_EP_TX_ICR_TX_DONE)) {
 		wil_dbg_irq(wil, "TX done\n");
 		isr &= ~BIT_DMA_EP_TX_ICR_TX_DONE;
@@ -532,20 +544,23 @@ static bool wil_validate_mbox_regs(struct wil6210_priv *wil)
 static irqreturn_t wil6210_irq_misc(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_DMA_EP_MISC_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
+
+	wil6210_mask_irq_misc(wil, false);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_DMA_EP_MISC_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
 
 	trace_wil6210_irq_misc(isr);
 	wil_dbg_irq(wil, "ISR MISC 0x%08x\n", isr);
 
 	if (!isr) {
 		wil_err(wil, "spurious IRQ: MISC\n");
+		wil6210_unmask_irq_misc(wil, false);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_misc(wil, false);
-
 	if (isr & ISR_MISC_FW_ERROR) {
 		u32 fw_assert_code = wil_r(wil, wil->rgf_fw_assert_code_addr);
 		u32 ucode_assert_code =
-- 
2.20.1

[PATCH AUTOSEL 4.19 008/158] ath: DFS JP domain W56 fixed pulse type 3 RADAR detection

[Sasha Levin]

From: Anilkumar Kolli <akolli@codeaurora.org>

[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]

Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.

Tested ath10k hw and fw:
	* QCA9888(10.4-3.5.1-00052)
	* QCA4019(10.4-3.2.1.1-00017)
	* QCA9984(10.4-3.6-00104)
	* QCA988X(10.2.4-1.0-00041)

Tested ath9k hw: AR9300

Tested-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/dfs_pattern_detector.c b/drivers/net/wireless/ath/dfs_pattern_detector.c
index d52b31b45df7..a274eb0d1968 100644
--- a/drivers/net/wireless/ath/dfs_pattern_detector.c
+++ b/drivers/net/wireless/ath/dfs_pattern_detector.c
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {
 	JP_PATTERN(0, 0, 1, 1428, 1428, 1, 18, 29, false),
 	JP_PATTERN(1, 2, 3, 3846, 3846, 1, 18, 29, false),
 	JP_PATTERN(2, 0, 1, 1388, 1388, 1, 18, 50, false),
-	JP_PATTERN(3, 1, 2, 4000, 4000, 1, 18, 50, false),
+	JP_PATTERN(3, 0, 4, 4000, 4000, 1, 18, 50, false),
 	JP_PATTERN(4, 0, 5, 150, 230, 1, 23, 50, false),
 	JP_PATTERN(5, 6, 10, 200, 500, 1, 16, 50, false),
 	JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
-- 
2.20.1

[PATCH AUTOSEL 4.19 009/158] regmap: debugfs: Fix memory leak in regmap_debugfs_init

[Sasha Levin]

From: Daniel Baluta <daniel.baluta@nxp.com>

[ Upstream commit 2899872b627e99b7586fe3b6c9f861da1b4d5072 ]

As detected by kmemleak running on i.MX6ULL board:

nreferenced object 0xd8366600 (size 64):
  comm "swapper/0", pid 1, jiffies 4294937370 (age 933.220s)
  hex dump (first 32 bytes):
    64 75 6d 6d 79 2d 69 6f 6d 75 78 63 2d 67 70 72  dummy-iomuxc-gpr
    40 32 30 65 34 30 30 30 00 e3 f3 ab fe d1 1b dd  @20e4000........
  backtrace:
    [<b0402aec>] kasprintf+0x2c/0x54
    [<a6fbad2c>] regmap_debugfs_init+0x7c/0x31c
    [<9c8d91fa>] __regmap_init+0xb5c/0xcf4
    [<5b1c3d2a>] of_syscon_register+0x164/0x2c4
    [<596a5d80>] syscon_node_to_regmap+0x64/0x90
    [<49bd597b>] imx6ul_init_machine+0x34/0xa0
    [<250a4dac>] customize_machine+0x1c/0x30
    [<2d19fdaf>] do_one_initcall+0x7c/0x398
    [<e6084469>] kernel_init_freeable+0x328/0x448
    [<168c9101>] kernel_init+0x8/0x114
    [<913268aa>] ret_from_fork+0x14/0x20
    [<ce7b131a>] 0x0

Root cause is that map->debugfs_name is allocated using kasprintf
and then the pointer is lost by assigning it other memory address.

Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/base/regmap/regmap-debugfs.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/base/regmap/regmap-debugfs.c b/drivers/base/regmap/regmap-debugfs.c
index 87b562e49a43..c9687c8b2347 100644
--- a/drivers/base/regmap/regmap-debugfs.c
+++ b/drivers/base/regmap/regmap-debugfs.c
@@ -575,6 +575,8 @@ void regmap_debugfs_init(struct regmap *map, const char *name)
 	}
 
 	if (!strcmp(name, "dummy")) {
+		kfree(map->debugfs_name);
+
 		map->debugfs_name = kasprintf(GFP_KERNEL, "dummy%d",
 						dummy_index);
 		name = map->debugfs_name;
-- 
2.20.1

[PATCH AUTOSEL 4.19 010/158] batman-adv: fix for leaked TVLV handler.

[Sasha Levin]

From: Jeremy Sowden <jeremy@azazel.net>

[ Upstream commit 17f78dd1bd624a4dd78ed5db3284a63ee807fcc3 ]

A handler for BATADV_TVLV_ROAM was being registered when the
translation-table was initialized, but not unregistered when the
translation-table was freed.  Unregister it.

Fixes: 122edaa05940 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
Reported-by: syzbot+d454a826e670502484b8@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/batman-adv/translation-table.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/net/batman-adv/translation-table.c b/net/batman-adv/translation-table.c
index 359ec1a6e822..9fa5389ea244 100644
--- a/net/batman-adv/translation-table.c
+++ b/net/batman-adv/translation-table.c
@@ -3821,6 +3821,8 @@ static void batadv_tt_purge(struct work_struct *work)
  */
 void batadv_tt_free(struct batadv_priv *bat_priv)
 {
+	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_ROAM, 1);
+
 	batadv_tvlv_container_unregister(bat_priv, BATADV_TVLV_TT, 1);
 	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_TT, 1);
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 011/158] media: dvb: usb: fix use after free in dvb_usb_device_exit

[Sasha Levin]

From: Oliver Neukum <oneukum@suse.com>

[ Upstream commit 6cf97230cd5f36b7665099083272595c55d72be7 ]

dvb_usb_device_exit() frees and uses the device name in that order.
Fix by storing the name in a buffer before freeing it.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+26ec41e9f788b3eba396@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/dvb-usb/dvb-usb-init.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/media/usb/dvb-usb/dvb-usb-init.c b/drivers/media/usb/dvb-usb/dvb-usb-init.c
index 40ca4eafb137..39ac22486bcd 100644
--- a/drivers/media/usb/dvb-usb/dvb-usb-init.c
+++ b/drivers/media/usb/dvb-usb/dvb-usb-init.c
@@ -287,12 +287,15 @@ EXPORT_SYMBOL(dvb_usb_device_init);
 void dvb_usb_device_exit(struct usb_interface *intf)
 {
 	struct dvb_usb_device *d = usb_get_intfdata(intf);
-	const char *name = "generic DVB-USB module";
+	const char *default_name = "generic DVB-USB module";
+	char name[40];
 
 	usb_set_intfdata(intf, NULL);
 	if (d != NULL && d->desc != NULL) {
-		name = d->desc->name;
+		strscpy(name, d->desc->name, sizeof(name));
 		dvb_usb_exit(d);
+	} else {
+		strscpy(name, default_name, sizeof(name));
 	}
 	info("%s successfully deinitialized and disconnected.", name);
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 012/158] media: spi: IR LED: add missing of table registration

[Sasha Levin]

From: Daniel Gomez <dagmcr@gmail.com>

[ Upstream commit 24e4cf770371df6ad49ed873f21618d9878f64c8 ]

MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.

Before this patch:
modinfo drivers/media/rc/ir-spi.ko  | grep alias

After this patch:
modinfo drivers/media/rc/ir-spi.ko  | grep alias
alias:          of:N*T*Cir-spi-ledC*
alias:          of:N*T*Cir-spi-led

Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/rc/ir-spi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/rc/ir-spi.c b/drivers/media/rc/ir-spi.c
index 66334e8d63ba..c58f2d38a458 100644
--- a/drivers/media/rc/ir-spi.c
+++ b/drivers/media/rc/ir-spi.c
@@ -161,6 +161,7 @@ static const struct of_device_id ir_spi_of_match[] = {
 	{ .compatible = "ir-spi-led" },
 	{},
 };
+MODULE_DEVICE_TABLE(of, ir_spi_of_match);
 
 static struct spi_driver ir_spi_driver = {
 	.probe = ir_spi_probe,
-- 
2.20.1

[PATCH AUTOSEL 4.19 013/158] crypto: talitos - fix skcipher failure due to wrong output IV

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit 3e03e792865ae48b8cfc69a0b4d65f02f467389f ]

Selftests report the following:

[    2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[    3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    3.043185] 00000000: fe dc ba 98 76 54 32 10
[    3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    3.073818] 00000000: 7d 33 88 93 0f 93 b2 42

This above dumps show that the actual output IV is indeed the input IV.
This is due to the IV not being copied back into the request.

This patch fixes that.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/crypto/talitos.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c
index c5859d3cb825..9cc5309a3fbf 100644
--- a/drivers/crypto/talitos.c
+++ b/drivers/crypto/talitos.c
@@ -1571,11 +1571,15 @@ static void ablkcipher_done(struct device *dev,
 			    int err)
 {
 	struct ablkcipher_request *areq = context;
+	struct crypto_ablkcipher *cipher = crypto_ablkcipher_reqtfm(areq);
+	struct talitos_ctx *ctx = crypto_ablkcipher_ctx(cipher);
+	unsigned int ivsize = crypto_ablkcipher_ivsize(cipher);
 	struct talitos_edesc *edesc;
 
 	edesc = container_of(desc, struct talitos_edesc, desc);
 
 	common_nonsnoop_unmap(dev, edesc, areq);
+	memcpy(areq->info, ctx->iv, ivsize);
 
 	kfree(edesc);
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 014/158] media: ov7740: avoid invalid framesize setting

[Sasha Levin]

From: Akinobu Mita <akinobu.mita@gmail.com>

[ Upstream commit 6e4ab830ac6d6a0d7cd7f87dc5d6536369bf24a8 ]

If the requested framesize by VIDIOC_SUBDEV_S_FMT is larger than supported
framesizes, it causes an out of bounds array access and the resulting
framesize is unexpected.

Avoid out of bounds array access and select the default framesize.

Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/ov7740.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/media/i2c/ov7740.c b/drivers/media/i2c/ov7740.c
index f5a1ee90a6c5..8a6a7a5929aa 100644
--- a/drivers/media/i2c/ov7740.c
+++ b/drivers/media/i2c/ov7740.c
@@ -761,7 +761,11 @@ static int ov7740_try_fmt_internal(struct v4l2_subdev *sd,
 
 		fsize++;
 	}
-
+	if (i >= ARRAY_SIZE(ov7740_framesizes)) {
+		fsize = &ov7740_framesizes[0];
+		fmt->width = fsize->width;
+		fmt->height = fsize->height;
+	}
 	if (ret_frmsize != NULL)
 		*ret_frmsize = fsize;
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 015/158] media: marvell-ccic: fix DMA s/g desc number calculation

[Sasha Levin]

From: Lubomir Rintel <lkundrak@v3.sk>

[ Upstream commit 0c7aa32966dab0b8a7424e1b34c7f206817953ec ]

The commit d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().

We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.

Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.

[mchehab+samsung@kernel.org: fix a checkpatch warning]

Fixes: d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/marvell-ccic/mcam-core.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/media/platform/marvell-ccic/mcam-core.c b/drivers/media/platform/marvell-ccic/mcam-core.c
index dfdbd4354b74..eeee15ff007d 100644
--- a/drivers/media/platform/marvell-ccic/mcam-core.c
+++ b/drivers/media/platform/marvell-ccic/mcam-core.c
@@ -200,7 +200,6 @@ struct mcam_vb_buffer {
 	struct list_head queue;
 	struct mcam_dma_desc *dma_desc;	/* Descriptor virtual address */
 	dma_addr_t dma_desc_pa;		/* Descriptor physical address */
-	int dma_desc_nent;		/* Number of mapped descriptors */
 };
 
 static inline struct mcam_vb_buffer *vb_to_mvb(struct vb2_v4l2_buffer *vb)
@@ -608,9 +607,11 @@ static void mcam_dma_contig_done(struct mcam_camera *cam, int frame)
 static void mcam_sg_next_buffer(struct mcam_camera *cam)
 {
 	struct mcam_vb_buffer *buf;
+	struct sg_table *sg_table;
 
 	buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, queue);
 	list_del_init(&buf->queue);
+	sg_table = vb2_dma_sg_plane_desc(&buf->vb_buf.vb2_buf, 0);
 	/*
 	 * Very Bad Not Good Things happen if you don't clear
 	 * C1_DESC_ENA before making any descriptor changes.
@@ -618,7 +619,7 @@ static void mcam_sg_next_buffer(struct mcam_camera *cam)
 	mcam_reg_clear_bit(cam, REG_CTRL1, C1_DESC_ENA);
 	mcam_reg_write(cam, REG_DMA_DESC_Y, buf->dma_desc_pa);
 	mcam_reg_write(cam, REG_DESC_LEN_Y,
-			buf->dma_desc_nent*sizeof(struct mcam_dma_desc));
+			sg_table->nents * sizeof(struct mcam_dma_desc));
 	mcam_reg_write(cam, REG_DESC_LEN_U, 0);
 	mcam_reg_write(cam, REG_DESC_LEN_V, 0);
 	mcam_reg_set_bit(cam, REG_CTRL1, C1_DESC_ENA);
-- 
2.20.1

[PATCH AUTOSEL 4.19 007/158] wil6210: fix spurious interrupts in 3-msi

[Sasha Levin]

From: Maya Erez <merez@codeaurora.org>

[ Upstream commit e10b0eddd5235aa5aef4e40b970e34e735611a80 ]

Interrupt is set in ICM (ICR & ~IMV) rising trigger.
As the driver masks the IRQ after clearing it, there can
be a race where an additional spurious interrupt is triggered
when the driver unmask the IRQ.
This can happen in case HW triggers an interrupt after the clear
and before the mask.

To prevent the second spurious interrupt the driver needs to mask the
IRQ before reading and clearing it.

Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/wil6210/interrupt.c | 65 ++++++++++++--------
 1 file changed, 40 insertions(+), 25 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/interrupt.c b/drivers/net/wireless/ath/wil6210/interrupt.c
index 5d287a8e1b45..0655cd884514 100644
--- a/drivers/net/wireless/ath/wil6210/interrupt.c
+++ b/drivers/net/wireless/ath/wil6210/interrupt.c
@@ -296,21 +296,24 @@ void wil_configure_interrupt_moderation(struct wil6210_priv *wil)
 static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_DMA_EP_RX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_rx(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_DMA_EP_RX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_rx(isr);
 	wil_dbg_irq(wil, "ISR RX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err_ratelimited(wil, "spurious IRQ: RX\n");
+		wil6210_unmask_irq_rx(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_rx(wil);
-
 	/* RX_DONE and RX_HTRSH interrupts are the same if interrupt
 	 * moderation is not used. Interrupt moderation may cause RX
 	 * buffer overflow while RX_DONE is delayed. The required
@@ -355,21 +358,24 @@ static irqreturn_t wil6210_irq_rx(int irq, void *cookie)
 static irqreturn_t wil6210_irq_rx_edma(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_INT_GEN_RX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_rx_edma(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_INT_GEN_RX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_rx(isr);
 	wil_dbg_irq(wil, "ISR RX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err(wil, "spurious IRQ: RX\n");
+		wil6210_unmask_irq_rx_edma(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_rx_edma(wil);
-
 	if (likely(isr & BIT_RX_STATUS_IRQ)) {
 		wil_dbg_irq(wil, "RX status ring\n");
 		isr &= ~BIT_RX_STATUS_IRQ;
@@ -403,21 +409,24 @@ static irqreturn_t wil6210_irq_rx_edma(int irq, void *cookie)
 static irqreturn_t wil6210_irq_tx_edma(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_INT_GEN_TX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_tx_edma(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_INT_GEN_TX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_tx(isr);
 	wil_dbg_irq(wil, "ISR TX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err(wil, "spurious IRQ: TX\n");
+		wil6210_unmask_irq_tx_edma(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_tx_edma(wil);
-
 	if (likely(isr & BIT_TX_STATUS_IRQ)) {
 		wil_dbg_irq(wil, "TX status ring\n");
 		isr &= ~BIT_TX_STATUS_IRQ;
@@ -446,21 +455,24 @@ static irqreturn_t wil6210_irq_tx_edma(int irq, void *cookie)
 static irqreturn_t wil6210_irq_tx(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_DMA_EP_TX_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
 	bool need_unmask = true;
 
+	wil6210_mask_irq_tx(wil);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_DMA_EP_TX_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
+
 	trace_wil6210_irq_tx(isr);
 	wil_dbg_irq(wil, "ISR TX 0x%08x\n", isr);
 
 	if (unlikely(!isr)) {
 		wil_err_ratelimited(wil, "spurious IRQ: TX\n");
+		wil6210_unmask_irq_tx(wil);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_tx(wil);
-
 	if (likely(isr & BIT_DMA_EP_TX_ICR_TX_DONE)) {
 		wil_dbg_irq(wil, "TX done\n");
 		isr &= ~BIT_DMA_EP_TX_ICR_TX_DONE;
@@ -532,20 +544,23 @@ static bool wil_validate_mbox_regs(struct wil6210_priv *wil)
 static irqreturn_t wil6210_irq_misc(int irq, void *cookie)
 {
 	struct wil6210_priv *wil = cookie;
-	u32 isr = wil_ioread32_and_clear(wil->csr +
-					 HOSTADDR(RGF_DMA_EP_MISC_ICR) +
-					 offsetof(struct RGF_ICR, ICR));
+	u32 isr;
+
+	wil6210_mask_irq_misc(wil, false);
+
+	isr = wil_ioread32_and_clear(wil->csr +
+				     HOSTADDR(RGF_DMA_EP_MISC_ICR) +
+				     offsetof(struct RGF_ICR, ICR));
 
 	trace_wil6210_irq_misc(isr);
 	wil_dbg_irq(wil, "ISR MISC 0x%08x\n", isr);
 
 	if (!isr) {
 		wil_err(wil, "spurious IRQ: MISC\n");
+		wil6210_unmask_irq_misc(wil, false);
 		return IRQ_NONE;
 	}
 
-	wil6210_mask_irq_misc(wil, false);
-
 	if (isr & ISR_MISC_FW_ERROR) {
 		u32 fw_assert_code = wil_r(wil, wil->rgf_fw_assert_code_addr);
 		u32 ucode_assert_code =
-- 
2.20.1