[PATCH AUTOSEL 4.14 001/105] wil6210: fix potential out-of-bounds read

[PATCH AUTOSEL 4.14 001/105] wil6210: fix potential out-of-bounds read

[Sasha Levin]

From: "Gustavo A. R. Silva" <gustavo@embeddedor.com>

[ Upstream commit bfabdd6997323adbedccb13a3fed1967fb8cf8f5 ]

Notice that *rc* can evaluate to up to 5, include/linux/netdevice.h:

enum gro_result {
        GRO_MERGED,
        GRO_MERGED_FREE,
        GRO_HELD,
        GRO_NORMAL,
        GRO_DROP,
        GRO_CONSUMED,
};
typedef enum gro_result gro_result_t;

In case *rc* evaluates to 5, we end up having an out-of-bounds read
at drivers/net/wireless/ath/wil6210/txrx.c:821:

	wil_dbg_txrx(wil, "Rx complete %d bytes => %s\n",
		     len, gro_res_str[rc]);

Fix this by adding element "GRO_CONSUMED" to array gro_res_str.

Addresses-Coverity-ID: 1444666 ("Out-of-bounds read")
Fixes: 194b482b5055 ("wil6210: Debug print GRO Rx result")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/wil6210/txrx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index 389c718cd257..16750056b8b5 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -732,6 +732,7 @@ void wil_netif_rx_any(struct sk_buff *skb, struct net_device *ndev)
 		[GRO_HELD]		= "GRO_HELD",
 		[GRO_NORMAL]		= "GRO_NORMAL",
 		[GRO_DROP]		= "GRO_DROP",
+		[GRO_CONSUMED]		= "GRO_CONSUMED",
 	};
 
 	if (ndev->features & NETIF_F_RXHASH)
-- 
2.20.1

[PATCH AUTOSEL 4.14 002/105] ath10k: Do not send probe response template for mesh

[Sasha Levin]

From: Surabhi Vishnoi <svishnoi@codeaurora.org>

[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]

Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.

To avoid this failure, skip sending probe response template to
firmware for mesh point.

Tested HW: WCN3990/QCA6174/QCA9984

Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index cdcfb175ad9b..58a3c42c4aed 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -1611,6 +1611,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
 	if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
 		return 0;
 
+	 /* For mesh, probe response and beacon share the same template */
+	if (ieee80211_vif_is_mesh(vif))
+		return 0;
+
 	prb = ieee80211_proberesp_get(hw, vif);
 	if (!prb) {
 		ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
-- 
2.20.1

[PATCH AUTOSEL 4.14 003/105] ath9k: Check for errors when reading SREV register

[Sasha Levin]

From: Tim Schumacher <timschumi@gmx.de>

[ Upstream commit 2f90c7e5d09437a4d8d5546feaae9f1cf48cfbe1 ]

Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.

    ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
    ath: phy2: Failed to read SREV register
    ath: phy2: Could not read hardware revision
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath: phy2: Unable to initialize hardware; initialization status: -95
    ath9k_htc: Failed to initialize the device

This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.

Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/hw.c | 32 +++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index a7f506eb7b36..406b52f114f0 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -250,8 +250,9 @@ void ath9k_hw_get_channel_centers(struct ath_hw *ah,
 /* Chip Revisions */
 /******************/
 
-static void ath9k_hw_read_revisions(struct ath_hw *ah)
+static bool ath9k_hw_read_revisions(struct ath_hw *ah)
 {
+	u32 srev;
 	u32 val;
 
 	if (ah->get_mac_revision)
@@ -267,25 +268,33 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 			val = REG_READ(ah, AR_SREV);
 			ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
 		}
-		return;
+		return true;
 	case AR9300_DEVID_AR9340:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9340;
-		return;
+		return true;
 	case AR9300_DEVID_QCA955X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9550;
-		return;
+		return true;
 	case AR9300_DEVID_AR953X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9531;
-		return;
+		return true;
 	case AR9300_DEVID_QCA956X:
 		ah->hw_version.macVersion = AR_SREV_VERSION_9561;
-		return;
+		return true;
 	}
 
-	val = REG_READ(ah, AR_SREV) & AR_SREV_ID;
+	srev = REG_READ(ah, AR_SREV);
+
+	if (srev == -EIO) {
+		ath_err(ath9k_hw_common(ah),
+			"Failed to read SREV register");
+		return false;
+	}
+
+	val = srev & AR_SREV_ID;
 
 	if (val == 0xFF) {
-		val = REG_READ(ah, AR_SREV);
+		val = srev;
 		ah->hw_version.macVersion =
 			(val & AR_SREV_VERSION2) >> AR_SREV_TYPE2_S;
 		ah->hw_version.macRev = MS(val, AR_SREV_REVISION2);
@@ -304,6 +313,8 @@ static void ath9k_hw_read_revisions(struct ath_hw *ah)
 		if (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE)
 			ah->is_pciexpress = true;
 	}
+
+	return true;
 }
 
 /************************************/
@@ -557,7 +568,10 @@ static int __ath9k_hw_init(struct ath_hw *ah)
 	struct ath_common *common = ath9k_hw_common(ah);
 	int r = 0;
 
-	ath9k_hw_read_revisions(ah);
+	if (!ath9k_hw_read_revisions(ah)) {
+		ath_err(common, "Could not read hardware revisions");
+		return -EOPNOTSUPP;
+	}
 
 	switch (ah->hw_version.macVersion) {
 	case AR_SREV_VERSION_5416_PCI:
-- 
2.20.1

[PATCH AUTOSEL 4.14 004/105] ath6kl: add some bounds checking

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 5d6751eaff672ea77642e74e92e6c0ac7f9709ab ]

The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements.  We need to add a couple bounds
checks to prevent array overflows.

I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.

Fixes: bdcd81707973 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath6kl/wmi.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath6kl/wmi.c b/drivers/net/wireless/ath/ath6kl/wmi.c
index bfc20b45b806..d79c2bccf582 100644
--- a/drivers/net/wireless/ath/ath6kl/wmi.c
+++ b/drivers/net/wireless/ath/ath6kl/wmi.c
@@ -1178,6 +1178,10 @@ static int ath6kl_wmi_pstream_timeout_event_rx(struct wmi *wmi, u8 *datap,
 		return -EINVAL;
 
 	ev = (struct wmi_pstream_timeout_event *) datap;
+	if (ev->traffic_class >= WMM_NUM_AC) {
+		ath6kl_err("invalid traffic class: %d\n", ev->traffic_class);
+		return -EINVAL;
+	}
 
 	/*
 	 * When the pstream (fat pipe == AC) timesout, it means there were
@@ -1519,6 +1523,10 @@ static int ath6kl_wmi_cac_event_rx(struct wmi *wmi, u8 *datap, int len,
 		return -EINVAL;
 
 	reply = (struct wmi_cac_event *) datap;
+	if (reply->ac >= WMM_NUM_AC) {
+		ath6kl_err("invalid AC: %d\n", reply->ac);
+		return -EINVAL;
+	}
 
 	if ((reply->cac_indication == CAC_INDICATION_ADMISSION_RESP) &&
 	    (reply->status_code != IEEE80211_TSPEC_STATUS_ADMISS_ACCEPTED)) {
@@ -2635,7 +2643,7 @@ int ath6kl_wmi_delete_pstream_cmd(struct wmi *wmi, u8 if_idx, u8 traffic_class,
 	u16 active_tsids = 0;
 	int ret;
 
-	if (traffic_class > 3) {
+	if (traffic_class >= WMM_NUM_AC) {
 		ath6kl_err("invalid traffic class: %d\n", traffic_class);
 		return -EINVAL;
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.14 005/105] x86/tsc: Use CPUID.0x16 to calculate missing crystal frequency

[Sasha Levin]

From: Daniel Drake <drake@endlessm.com>

[ Upstream commit 604dc9170f2435d27da5039a3efd757dceadc684 ]

native_calibrate_tsc() had a data mapping Intel CPU families
and crystal clock speed, but hardcoded tables are not ideal, and this
approach was already problematic at least in the Skylake X case, as
seen in commit:

  b51120309348 ("x86/tsc: Fix erroneous TSC rate on Skylake Xeon")

By examining CPUID data from http://instlatx64.atw.hu/ and units
in the lab, we have found that 3 different scenarios need to be dealt
with, and we can eliminate most of the hardcoded data using an approach a
little more advanced than before:

 1. ApolloLake, GeminiLake, CannonLake (and presumably all new chipsets
    from this point) report the crystal frequency directly via CPUID.0x15.
    That's definitive data that we can rely upon.

 2. Skylake, Kabylake and all variants of those two chipsets report a
    crystal frequency of zero, however we can calculate the crystal clock
    speed by condidering data from CPUID.0x16.

    This method correctly distinguishes between the two crystal clock
    frequencies present on different Skylake X variants that caused
    headaches before.

    As the calculations do not quite match the previously-hardcoded values
    in some cases (e.g. 23913043Hz instead of 24MHz), TSC refinement is
    enabled on all platforms where we had to calculate the crystal
    frequency in this way.

 3. Denverton (GOLDMONT_X) reports a crystal frequency of zero and does
    not support CPUID.0x16, so we leave this entry hardcoded.

Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: len.brown@intel.com
Cc: linux@endlessm.com
Cc: rafael.j.wysocki@intel.com
Link: http://lkml.kernel.org/r/20190509055417.13152-1-drake@endlessm.com
Link: https://lkml.kernel.org/r/20190419083533.32388-1-drake@endlessm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/tsc.c | 47 +++++++++++++++++++++++++------------------
 1 file changed, 27 insertions(+), 20 deletions(-)

diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c
index 5d681fe6d352..e501bd7f39fc 100644
--- a/arch/x86/kernel/tsc.c
+++ b/arch/x86/kernel/tsc.c
@@ -612,31 +612,38 @@ unsigned long native_calibrate_tsc(void)
 
 	crystal_khz = ecx_hz / 1000;
 
-	if (crystal_khz == 0) {
-		switch (boot_cpu_data.x86_model) {
-		case INTEL_FAM6_SKYLAKE_MOBILE:
-		case INTEL_FAM6_SKYLAKE_DESKTOP:
-		case INTEL_FAM6_KABYLAKE_MOBILE:
-		case INTEL_FAM6_KABYLAKE_DESKTOP:
-			crystal_khz = 24000;	/* 24.0 MHz */
-			break;
-		case INTEL_FAM6_ATOM_GOLDMONT_X:
-			crystal_khz = 25000;	/* 25.0 MHz */
-			break;
-		case INTEL_FAM6_ATOM_GOLDMONT:
-			crystal_khz = 19200;	/* 19.2 MHz */
-			break;
-		}
-	}
+	/*
+	 * Denverton SoCs don't report crystal clock, and also don't support
+	 * CPUID.0x16 for the calculation below, so hardcode the 25MHz crystal
+	 * clock.
+	 */
+	if (crystal_khz == 0 &&
+			boot_cpu_data.x86_model == INTEL_FAM6_ATOM_GOLDMONT_X)
+		crystal_khz = 25000;
 
-	if (crystal_khz == 0)
-		return 0;
 	/*
-	 * TSC frequency determined by CPUID is a "hardware reported"
+	 * TSC frequency reported directly by CPUID is a "hardware reported"
 	 * frequency and is the most accurate one so far we have. This
 	 * is considered a known frequency.
 	 */
-	setup_force_cpu_cap(X86_FEATURE_TSC_KNOWN_FREQ);
+	if (crystal_khz != 0)
+		setup_force_cpu_cap(X86_FEATURE_TSC_KNOWN_FREQ);
+
+	/*
+	 * Some Intel SoCs like Skylake and Kabylake don't report the crystal
+	 * clock, but we can easily calculate it to a high degree of accuracy
+	 * by considering the crystal ratio and the CPU speed.
+	 */
+	if (crystal_khz == 0 && boot_cpu_data.cpuid_level >= 0x16) {
+		unsigned int eax_base_mhz, ebx, ecx, edx;
+
+		cpuid(0x16, &eax_base_mhz, &ebx, &ecx, &edx);
+		crystal_khz = eax_base_mhz * 1000 *
+			eax_denominator / ebx_numerator;
+	}
+
+	if (crystal_khz == 0)
+		return 0;
 
 	/*
 	 * For Atom SoCs TSC is the only reliable clocksource.
-- 
2.20.1

[PATCH AUTOSEL 4.14 006/105] ath: DFS JP domain W56 fixed pulse type 3 RADAR detection

[Sasha Levin]

From: Anilkumar Kolli <akolli@codeaurora.org>

[ Upstream commit d8792393a783158cbb2c39939cb897dc5e5299b6 ]

Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.

Tested ath10k hw and fw:
	* QCA9888(10.4-3.5.1-00052)
	* QCA4019(10.4-3.2.1.1-00017)
	* QCA9984(10.4-3.6-00104)
	* QCA988X(10.2.4-1.0-00041)

Tested ath9k hw: AR9300

Tested-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/dfs_pattern_detector.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/dfs_pattern_detector.c b/drivers/net/wireless/ath/dfs_pattern_detector.c
index 4100ffd42a43..78146607f16e 100644
--- a/drivers/net/wireless/ath/dfs_pattern_detector.c
+++ b/drivers/net/wireless/ath/dfs_pattern_detector.c
@@ -111,7 +111,7 @@ static const struct radar_detector_specs jp_radar_ref_types[] = {
 	JP_PATTERN(0, 0, 1, 1428, 1428, 1, 18, 29, false),
 	JP_PATTERN(1, 2, 3, 3846, 3846, 1, 18, 29, false),
 	JP_PATTERN(2, 0, 1, 1388, 1388, 1, 18, 50, false),
-	JP_PATTERN(3, 1, 2, 4000, 4000, 1, 18, 50, false),
+	JP_PATTERN(3, 0, 4, 4000, 4000, 1, 18, 50, false),
 	JP_PATTERN(4, 0, 5, 150, 230, 1, 23, 50, false),
 	JP_PATTERN(5, 6, 10, 200, 500, 1, 16, 50, false),
 	JP_PATTERN(6, 11, 20, 200, 500, 1, 12, 50, false),
-- 
2.20.1

[PATCH AUTOSEL 4.14 007/105] batman-adv: fix for leaked TVLV handler.

[Sasha Levin]

From: Jeremy Sowden <jeremy@azazel.net>

[ Upstream commit 17f78dd1bd624a4dd78ed5db3284a63ee807fcc3 ]

A handler for BATADV_TVLV_ROAM was being registered when the
translation-table was initialized, but not unregistered when the
translation-table was freed.  Unregister it.

Fixes: 122edaa05940 ("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")
Reported-by: syzbot+d454a826e670502484b8@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/batman-adv/translation-table.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/net/batman-adv/translation-table.c b/net/batman-adv/translation-table.c
index 020a8adc4cce..2c2670b85fa9 100644
--- a/net/batman-adv/translation-table.c
+++ b/net/batman-adv/translation-table.c
@@ -3750,6 +3750,8 @@ static void batadv_tt_purge(struct work_struct *work)
 
 void batadv_tt_free(struct batadv_priv *bat_priv)
 {
+	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_ROAM, 1);
+
 	batadv_tvlv_container_unregister(bat_priv, BATADV_TVLV_TT, 1);
 	batadv_tvlv_handler_unregister(bat_priv, BATADV_TVLV_TT, 1);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 008/105] media: dvb: usb: fix use after free in dvb_usb_device_exit

[Sasha Levin]

From: Oliver Neukum <oneukum@suse.com>

[ Upstream commit 6cf97230cd5f36b7665099083272595c55d72be7 ]

dvb_usb_device_exit() frees and uses the device name in that order.
Fix by storing the name in a buffer before freeing it.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+26ec41e9f788b3eba396@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/dvb-usb/dvb-usb-init.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/media/usb/dvb-usb/dvb-usb-init.c b/drivers/media/usb/dvb-usb/dvb-usb-init.c
index 84308569e7dc..b3413404f91a 100644
--- a/drivers/media/usb/dvb-usb/dvb-usb-init.c
+++ b/drivers/media/usb/dvb-usb/dvb-usb-init.c
@@ -287,12 +287,15 @@ EXPORT_SYMBOL(dvb_usb_device_init);
 void dvb_usb_device_exit(struct usb_interface *intf)
 {
 	struct dvb_usb_device *d = usb_get_intfdata(intf);
-	const char *name = "generic DVB-USB module";
+	const char *default_name = "generic DVB-USB module";
+	char name[40];
 
 	usb_set_intfdata(intf, NULL);
 	if (d != NULL && d->desc != NULL) {
-		name = d->desc->name;
+		strscpy(name, d->desc->name, sizeof(name));
 		dvb_usb_exit(d);
+	} else {
+		strscpy(name, default_name, sizeof(name));
 	}
 	info("%s successfully deinitialized and disconnected.", name);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 009/105] media: spi: IR LED: add missing of table registration

[Sasha Levin]

From: Daniel Gomez <dagmcr@gmail.com>

[ Upstream commit 24e4cf770371df6ad49ed873f21618d9878f64c8 ]

MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.

Before this patch:
modinfo drivers/media/rc/ir-spi.ko  | grep alias

After this patch:
modinfo drivers/media/rc/ir-spi.ko  | grep alias
alias:          of:N*T*Cir-spi-ledC*
alias:          of:N*T*Cir-spi-led

Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/rc/ir-spi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/rc/ir-spi.c b/drivers/media/rc/ir-spi.c
index 29ed0638cb74..cbe585f95715 100644
--- a/drivers/media/rc/ir-spi.c
+++ b/drivers/media/rc/ir-spi.c
@@ -186,6 +186,7 @@ static const struct of_device_id ir_spi_of_match[] = {
 	{ .compatible = "ir-spi-led" },
 	{},
 };
+MODULE_DEVICE_TABLE(of, ir_spi_of_match);
 
 static struct spi_driver ir_spi_driver = {
 	.probe = ir_spi_probe,
-- 
2.20.1

[PATCH AUTOSEL 4.14 010/105] crypto: talitos - fix skcipher failure due to wrong output IV

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit 3e03e792865ae48b8cfc69a0b4d65f02f467389f ]

Selftests report the following:

[    2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[    3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    3.043185] 00000000: fe dc ba 98 76 54 32 10
[    3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[    3.073818] 00000000: 7d 33 88 93 0f 93 b2 42

This above dumps show that the actual output IV is indeed the input IV.
This is due to the IV not being copied back into the request.

This patch fixes that.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/crypto/talitos.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c
index 4388f4e3840c..33fcedeb5f9f 100644
--- a/drivers/crypto/talitos.c
+++ b/drivers/crypto/talitos.c
@@ -1544,11 +1544,15 @@ static void ablkcipher_done(struct device *dev,
 			    int err)
 {
 	struct ablkcipher_request *areq = context;
+	struct crypto_ablkcipher *cipher = crypto_ablkcipher_reqtfm(areq);
+	struct talitos_ctx *ctx = crypto_ablkcipher_ctx(cipher);
+	unsigned int ivsize = crypto_ablkcipher_ivsize(cipher);
 	struct talitos_edesc *edesc;
 
 	edesc = container_of(desc, struct talitos_edesc, desc);
 
 	common_nonsnoop_unmap(dev, edesc, areq);
+	memcpy(areq->info, ctx->iv, ivsize);
 
 	kfree(edesc);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 011/105] media: marvell-ccic: fix DMA s/g desc number calculation

[Sasha Levin]

From: Lubomir Rintel <lkundrak@v3.sk>

[ Upstream commit 0c7aa32966dab0b8a7424e1b34c7f206817953ec ]

The commit d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().

We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.

Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.

[mchehab+samsung@kernel.org: fix a checkpatch warning]

Fixes: d790b7eda953 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/marvell-ccic/mcam-core.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/media/platform/marvell-ccic/mcam-core.c b/drivers/media/platform/marvell-ccic/mcam-core.c
index 7b7250b1cff8..4ecb94860aa4 100644
--- a/drivers/media/platform/marvell-ccic/mcam-core.c
+++ b/drivers/media/platform/marvell-ccic/mcam-core.c
@@ -200,7 +200,6 @@ struct mcam_vb_buffer {
 	struct list_head queue;
 	struct mcam_dma_desc *dma_desc;	/* Descriptor virtual address */
 	dma_addr_t dma_desc_pa;		/* Descriptor physical address */
-	int dma_desc_nent;		/* Number of mapped descriptors */
 };
 
 static inline struct mcam_vb_buffer *vb_to_mvb(struct vb2_v4l2_buffer *vb)
@@ -608,9 +607,11 @@ static void mcam_dma_contig_done(struct mcam_camera *cam, int frame)
 static void mcam_sg_next_buffer(struct mcam_camera *cam)
 {
 	struct mcam_vb_buffer *buf;
+	struct sg_table *sg_table;
 
 	buf = list_first_entry(&cam->buffers, struct mcam_vb_buffer, queue);
 	list_del_init(&buf->queue);
+	sg_table = vb2_dma_sg_plane_desc(&buf->vb_buf.vb2_buf, 0);
 	/*
 	 * Very Bad Not Good Things happen if you don't clear
 	 * C1_DESC_ENA before making any descriptor changes.
@@ -618,7 +619,7 @@ static void mcam_sg_next_buffer(struct mcam_camera *cam)
 	mcam_reg_clear_bit(cam, REG_CTRL1, C1_DESC_ENA);
 	mcam_reg_write(cam, REG_DMA_DESC_Y, buf->dma_desc_pa);
 	mcam_reg_write(cam, REG_DESC_LEN_Y,
-			buf->dma_desc_nent*sizeof(struct mcam_dma_desc));
+			sg_table->nents * sizeof(struct mcam_dma_desc));
 	mcam_reg_write(cam, REG_DESC_LEN_U, 0);
 	mcam_reg_write(cam, REG_DESC_LEN_V, 0);
 	mcam_reg_set_bit(cam, REG_CTRL1, C1_DESC_ENA);
-- 
2.20.1

[PATCH AUTOSEL 4.14 012/105] media: vpss: fix a potential NULL pointer dereference

[Sasha Levin]

From: Kangjie Lu <kjlu@umn.edu>

[ Upstream commit e08f0761234def47961d3252eac09ccedfe4c6a0 ]

In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereference.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/davinci/vpss.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/media/platform/davinci/vpss.c b/drivers/media/platform/davinci/vpss.c
index f2d27b932999..2ee4cd9e6d80 100644
--- a/drivers/media/platform/davinci/vpss.c
+++ b/drivers/media/platform/davinci/vpss.c
@@ -518,6 +518,11 @@ static int __init vpss_init(void)
 		return -EBUSY;
 
 	oper_cfg.vpss_regs_base2 = ioremap(VPSS_CLK_CTRL, 4);
+	if (unlikely(!oper_cfg.vpss_regs_base2)) {
+		release_mem_region(VPSS_CLK_CTRL, 4);
+		return -ENOMEM;
+	}
+
 	writel(VPSS_CLK_CTRL_VENCCLKEN |
 		     VPSS_CLK_CTRL_DACCLKEN, oper_cfg.vpss_regs_base2);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 013/105] media: media_device_enum_links32: clean a reserved field

[Sasha Levin]

From: Jungo Lin <jungo.lin@mediatek.com>

[ Upstream commit f49308878d7202e07d8761238e01bd0e5fce2750 ]

In v4l2-compliance utility, test MEDIA_IOC_ENUM_ENTITIES
will check whether reserved field of media_links_enum filled
with zero.

However, for 32 bit program, the reserved field is missing
copy from kernel space to user space in media_device_enum_links32
function.

This patch adds the cleaning a reserved field logic in
media_device_enum_links32 function.

Signed-off-by: Jungo Lin <jungo.lin@mediatek.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/media-device.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/media/media-device.c b/drivers/media/media-device.c
index 62b2c5d9bdfb..a6d56154fac7 100644
--- a/drivers/media/media-device.c
+++ b/drivers/media/media-device.c
@@ -470,6 +470,7 @@ static long media_device_enum_links32(struct media_device *mdev,
 {
 	struct media_links_enum links;
 	compat_uptr_t pads_ptr, links_ptr;
+	int ret;
 
 	memset(&links, 0, sizeof(links));
 
@@ -481,7 +482,13 @@ static long media_device_enum_links32(struct media_device *mdev,
 	links.pads = compat_ptr(pads_ptr);
 	links.links = compat_ptr(links_ptr);
 
-	return media_device_enum_links(mdev, &links);
+	ret = media_device_enum_links(mdev, &links);
+	if (ret)
+		return ret;
+
+	memset(ulinks->reserved, 0, sizeof(ulinks->reserved));
+
+	return 0;
 }
 
 #define MEDIA_IOC_ENUM_LINKS32		_IOWR('|', 0x02, struct media_links_enum32)
-- 
2.20.1

[PATCH AUTOSEL 4.14 014/105] net: stmmac: dwmac1000: Clear unused address entries

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 9463c445590091202659cdfdd44b236acadfbd84 ]

In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.

Found out while running stmmac selftests.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
index 540d21786a43..08dd6a06ac58 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
@@ -217,6 +217,12 @@ static void dwmac1000_set_filter(struct mac_device_info *hw,
 					    GMAC_ADDR_LOW(reg));
 			reg++;
 		}
+
+		while (reg <= perfect_addr_number) {
+			writel(0, ioaddr + GMAC_ADDR_HIGH(reg));
+			writel(0, ioaddr + GMAC_ADDR_LOW(reg));
+			reg++;
+		}
 	}
 
 #ifdef FRAME_FILTER_DEBUG
-- 
2.20.1

[PATCH AUTOSEL 4.14 015/105] net: stmmac: dwmac4/5: Clear unused address entries

[Sasha Levin]

From: Jose Abreu <Jose.Abreu@synopsys.com>

[ Upstream commit 0620ec6c62a5a07625b65f699adc5d1b90394ee6 ]

In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.

Found out while running stmmac selftests.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
index 55ae14a6bb8c..ed5fcd4994f2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
@@ -443,14 +443,20 @@ static void dwmac4_set_filter(struct mac_device_info *hw,
 		 * are required
 		 */
 		value |= GMAC_PACKET_FILTER_PR;
-	} else if (!netdev_uc_empty(dev)) {
-		int reg = 1;
+	} else {
 		struct netdev_hw_addr *ha;
+		int reg = 1;
 
 		netdev_for_each_uc_addr(ha, dev) {
 			dwmac4_set_umac_addr(hw, ha->addr, reg);
 			reg++;
 		}
+
+		while (reg <= GMAC_MAX_PERFECT_ADDRESSES) {
+			writel(0, ioaddr + GMAC_ADDR_HIGH(reg));
+			writel(0, ioaddr + GMAC_ADDR_LOW(reg));
+			reg++;
+		}
 	}
 
 	writel(value, ioaddr + GMAC_PACKET_FILTER);
-- 
2.20.1

[PATCH AUTOSEL 4.14 016/105] qed: Set the doorbell address correctly

[Sasha Levin]

From: Michal Kalderon <michal.kalderon@marvell.com>

[ Upstream commit 8366d520019f366fabd6c7a13032bdcd837e18d4 ]

In 100g mode the doorbell bar is united for both engines. Set
the correct offset in the hwfn so that the doorbell returned
for RoCE is in the affined hwfn.

Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Denis Bolotin <denis.bolotin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/qlogic/qed/qed_dev.c  | 29 ++++++++++++++--------
 drivers/net/ethernet/qlogic/qed/qed_rdma.c |  2 +-
 2 files changed, 19 insertions(+), 12 deletions(-)

diff --git a/drivers/net/ethernet/qlogic/qed/qed_dev.c b/drivers/net/ethernet/qlogic/qed/qed_dev.c
index 410528e7d927..c4e8bf0773fe 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_dev.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_dev.c
@@ -2947,6 +2947,7 @@ static int qed_get_dev_info(struct qed_hwfn *p_hwfn, struct qed_ptt *p_ptt)
 static int qed_hw_prepare_single(struct qed_hwfn *p_hwfn,
 				 void __iomem *p_regview,
 				 void __iomem *p_doorbells,
+				 u64 db_phys_addr,
 				 enum qed_pci_personality personality)
 {
 	int rc = 0;
@@ -2954,6 +2955,7 @@ static int qed_hw_prepare_single(struct qed_hwfn *p_hwfn,
 	/* Split PCI bars evenly between hwfns */
 	p_hwfn->regview = p_regview;
 	p_hwfn->doorbells = p_doorbells;
+	p_hwfn->db_phys_addr = db_phys_addr;
 
 	if (IS_VF(p_hwfn->cdev))
 		return qed_vf_hw_prepare(p_hwfn);
@@ -3036,7 +3038,9 @@ int qed_hw_prepare(struct qed_dev *cdev,
 	/* Initialize the first hwfn - will learn number of hwfns */
 	rc = qed_hw_prepare_single(p_hwfn,
 				   cdev->regview,
-				   cdev->doorbells, personality);
+				   cdev->doorbells,
+				   cdev->db_phys_addr,
+				   personality);
 	if (rc)
 		return rc;
 
@@ -3045,22 +3049,25 @@ int qed_hw_prepare(struct qed_dev *cdev,
 	/* Initialize the rest of the hwfns */
 	if (cdev->num_hwfns > 1) {
 		void __iomem *p_regview, *p_doorbell;
-		u8 __iomem *addr;
+		u64 db_phys_addr;
+		u32 offset;
 
 		/* adjust bar offset for second engine */
-		addr = cdev->regview +
-		       qed_hw_bar_size(p_hwfn, p_hwfn->p_main_ptt,
-				       BAR_ID_0) / 2;
-		p_regview = addr;
+		offset = qed_hw_bar_size(p_hwfn, p_hwfn->p_main_ptt,
+					 BAR_ID_0) / 2;
+		p_regview = cdev->regview + offset;
 
-		addr = cdev->doorbells +
-		       qed_hw_bar_size(p_hwfn, p_hwfn->p_main_ptt,
-				       BAR_ID_1) / 2;
-		p_doorbell = addr;
+		offset = qed_hw_bar_size(p_hwfn, p_hwfn->p_main_ptt,
+					 BAR_ID_1) / 2;
+
+		p_doorbell = cdev->doorbells + offset;
+
+		db_phys_addr = cdev->db_phys_addr + offset;
 
 		/* prepare second hw function */
 		rc = qed_hw_prepare_single(&cdev->hwfns[1], p_regview,
-					   p_doorbell, personality);
+					   p_doorbell, db_phys_addr,
+					   personality);
 
 		/* in case of error, need to free the previously
 		 * initiliazed hwfn 0.
diff --git a/drivers/net/ethernet/qlogic/qed/qed_rdma.c b/drivers/net/ethernet/qlogic/qed/qed_rdma.c
index 1b6554866138..1e13dea66989 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_rdma.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_rdma.c
@@ -753,7 +753,7 @@ static int qed_rdma_add_user(void *rdma_cxt,
 				     dpi_start_offset +
 				     ((out_params->dpi) * p_hwfn->dpi_size));
 
-	out_params->dpi_phys_addr = p_hwfn->cdev->db_phys_addr +
+	out_params->dpi_phys_addr = p_hwfn->db_phys_addr +
 				    dpi_start_offset +
 				    ((out_params->dpi) * p_hwfn->dpi_size);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 017/105] signal/pid_namespace: Fix reboot_pid_ns to use send_sig not force_sig

[Sasha Levin]

From: "Eric W. Biederman" <ebiederm@xmission.com>

[ Upstream commit f9070dc94542093fd516ae4ccea17ef46a4362c5 ]

The locking in force_sig_info is not prepared to deal with a task that
exits or execs (as sighand may change).  The is not a locking problem
in force_sig as force_sig is only built to handle synchronous
exceptions.

Further the function force_sig_info changes the signal state if the
signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the
delivery of the signal.  The signal SIGKILL can not be ignored and can
not be blocked and SIGNAL_UNKILLABLE won't prevent it from being
delivered.

So using force_sig rather than send_sig for SIGKILL is confusing
and pointless.

Because it won't impact the sending of the signal and and because
using force_sig is wrong, replace force_sig with send_sig.

Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Fixes: cf3f89214ef6 ("pidns: add reboot_pid_ns() to handle the reboot syscall")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/pid_namespace.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/pid_namespace.c b/kernel/pid_namespace.c
index 4918314893bc..22091c88b3bb 100644
--- a/kernel/pid_namespace.c
+++ b/kernel/pid_namespace.c
@@ -351,7 +351,7 @@ int reboot_pid_ns(struct pid_namespace *pid_ns, int cmd)
 	}
 
 	read_lock(&tasklist_lock);
-	force_sig(SIGKILL, pid_ns->child_reaper);
+	send_sig(SIGKILL, pid_ns->child_reaper, 1);
 	read_unlock(&tasklist_lock);
 
 	do_exit(0);
-- 
2.20.1

[PATCH AUTOSEL 4.14 018/105] signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig

[Sasha Levin]

From: "Eric W. Biederman" <ebiederm@xmission.com>

[ Upstream commit 72abe3bcf0911d69b46c1e8bdb5612675e0ac42c ]

The locking in force_sig_info is not prepared to deal with a task that
exits or execs (as sighand may change).  The is not a locking problem
in force_sig as force_sig is only built to handle synchronous
exceptions.

Further the function force_sig_info changes the signal state if the
signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the
delivery of the signal.  The signal SIGKILL can not be ignored and can
not be blocked and SIGNAL_UNKILLABLE won't prevent it from being
delivered.

So using force_sig rather than send_sig for SIGKILL is confusing
and pointless.

Because it won't impact the sending of the signal and and because
using force_sig is wrong, replace force_sig with send_sig.

Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Jeff Layton <jlayton@primarydata.com>
Cc: Steve French <smfrench@gmail.com>
Fixes: a5c3e1c725af ("Revert "cifs: No need to send SIGKILL to demux_thread during umount"")
Fixes: e7ddee9037e7 ("cifs: disable sharing session and tcon and add new TCP sharing code")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/cifs/connect.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/cifs/connect.c b/fs/cifs/connect.c
index 33cd844579ae..ebc5714fea95 100644
--- a/fs/cifs/connect.c
+++ b/fs/cifs/connect.c
@@ -2320,7 +2320,7 @@ cifs_put_tcp_session(struct TCP_Server_Info *server, int from_reconnect)
 
 	task = xchg(&server->tsk, NULL);
 	if (task)
-		force_sig(SIGKILL, task);
+		send_sig(SIGKILL, task, 1);
 }
 
 static struct TCP_Server_Info *
-- 
2.20.1

[PATCH AUTOSEL 4.14 019/105] af_key: fix leaks in key_pol_get_resp and dump_sp.

[Sasha Levin]

From: Jeremy Sowden <jeremy@azazel.net>

[ Upstream commit 7c80eb1c7e2b8420477fbc998971d62a648035d9 ]

In both functions, if pfkey_xfrm_policy2msg failed we leaked the newly
allocated sk_buff.  Free it on error.

Fixes: 55569ce256ce ("Fix conversion between IPSEC_MODE_xxx and XFRM_MODE_xxx.")
Reported-by: syzbot+4f0529365f7f2208d9f0@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/key/af_key.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/net/key/af_key.c b/net/key/af_key.c
index b095551a5773..ac38b47e9f86 100644
--- a/net/key/af_key.c
+++ b/net/key/af_key.c
@@ -2438,8 +2438,10 @@ static int key_pol_get_resp(struct sock *sk, struct xfrm_policy *xp, const struc
 		goto out;
 	}
 	err = pfkey_xfrm_policy2msg(out_skb, xp, dir);
-	if (err < 0)
+	if (err < 0) {
+		kfree_skb(out_skb);
 		goto out;
+	}
 
 	out_hdr = (struct sadb_msg *) out_skb->data;
 	out_hdr->sadb_msg_version = hdr->sadb_msg_version;
@@ -2690,8 +2692,10 @@ static int dump_sp(struct xfrm_policy *xp, int dir, int count, void *ptr)
 		return PTR_ERR(out_skb);
 
 	err = pfkey_xfrm_policy2msg(out_skb, xp, dir);
-	if (err < 0)
+	if (err < 0) {
+		kfree_skb(out_skb);
 		return err;
+	}
 
 	out_hdr = (struct sadb_msg *) out_skb->data;
 	out_hdr->sadb_msg_version = pfk->dump.msg_version;
-- 
2.20.1

[PATCH AUTOSEL 4.14 020/105] xfrm: Fix xfrm sel prefix length validation

[Sasha Levin]

From: Anirudh Gupta <anirudhrudr@gmail.com>

[ Upstream commit b38ff4075a80b4da5cb2202d7965332ca0efb213 ]

Family of src/dst can be different from family of selector src/dst.
Use xfrm selector family to validate address prefix length,
while verifying new sa from userspace.

Validated patch with this command:
ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \
reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \
0x1111016400000000000000000000000044440001 128 \
sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5

Fixes: 07bf7908950a ("xfrm: Validate address prefix lengths in the xfrm selector.")
Signed-off-by: Anirudh Gupta <anirudh.gupta@sophos.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/xfrm/xfrm_user.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/net/xfrm/xfrm_user.c b/net/xfrm/xfrm_user.c
index 919b8406028c..b25b68ae7c74 100644
--- a/net/xfrm/xfrm_user.c
+++ b/net/xfrm/xfrm_user.c
@@ -150,6 +150,22 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
 
 	err = -EINVAL;
 	switch (p->family) {
+	case AF_INET:
+		break;
+
+	case AF_INET6:
+#if IS_ENABLED(CONFIG_IPV6)
+		break;
+#else
+		err = -EAFNOSUPPORT;
+		goto out;
+#endif
+
+	default:
+		goto out;
+	}
+
+	switch (p->sel.family) {
 	case AF_INET:
 		if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
 			goto out;
-- 
2.20.1

[PATCH AUTOSEL 4.14 021/105] fscrypt: clean up some BUG_ON()s in block encryption/decryption

[Sasha Levin]

From: Eric Biggers <ebiggers@google.com>

[ Upstream commit eeacfdc68a104967162dfcba60f53f6f5b62a334 ]

Replace some BUG_ON()s with WARN_ON_ONCE() and returning an error code,
and move the check for len divisible by FS_CRYPTO_BLOCK_SIZE into
fscrypt_crypt_block() so that it's done for both encryption and
decryption, not just encryption.

Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/crypto/crypto.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/fs/crypto/crypto.c b/fs/crypto/crypto.c
index daf2683f0655..f862ad19c714 100644
--- a/fs/crypto/crypto.c
+++ b/fs/crypto/crypto.c
@@ -157,7 +157,10 @@ int fscrypt_do_page_crypto(const struct inode *inode, fscrypt_direction_t rw,
 	struct crypto_skcipher *tfm = ci->ci_ctfm;
 	int res = 0;
 
-	BUG_ON(len == 0);
+	if (WARN_ON_ONCE(len <= 0))
+		return -EINVAL;
+	if (WARN_ON_ONCE(len % FS_CRYPTO_BLOCK_SIZE != 0))
+		return -EINVAL;
 
 	BUILD_BUG_ON(sizeof(iv) != FS_IV_SIZE);
 	BUILD_BUG_ON(AES_BLOCK_SIZE != FS_IV_SIZE);
@@ -257,8 +260,6 @@ struct page *fscrypt_encrypt_page(const struct inode *inode,
 	struct page *ciphertext_page = page;
 	int err;
 
-	BUG_ON(len % FS_CRYPTO_BLOCK_SIZE != 0);
-
 	if (inode->i_sb->s_cop->flags & FS_CFLG_OWN_PAGES) {
 		/* with inplace-encryption we just encrypt the page */
 		err = fscrypt_do_page_crypto(inode, FS_ENCRYPT, lblk_num, page,
@@ -270,7 +271,8 @@ struct page *fscrypt_encrypt_page(const struct inode *inode,
 		return ciphertext_page;
 	}
 
-	BUG_ON(!PageLocked(page));
+	if (WARN_ON_ONCE(!PageLocked(page)))
+		return ERR_PTR(-EINVAL);
 
 	ctx = fscrypt_get_ctx(inode, gfp_flags);
 	if (IS_ERR(ctx))
@@ -318,8 +320,9 @@ EXPORT_SYMBOL(fscrypt_encrypt_page);
 int fscrypt_decrypt_page(const struct inode *inode, struct page *page,
 			unsigned int len, unsigned int offs, u64 lblk_num)
 {
-	if (!(inode->i_sb->s_cop->flags & FS_CFLG_OWN_PAGES))
-		BUG_ON(!PageLocked(page));
+	if (WARN_ON_ONCE(!PageLocked(page) &&
+			 !(inode->i_sb->s_cop->flags & FS_CFLG_OWN_PAGES)))
+		return -EINVAL;
 
 	return fscrypt_do_page_crypto(inode, FS_DECRYPT, lblk_num, page, page,
 				      len, offs, GFP_NOFS);
-- 
2.20.1

[PATCH AUTOSEL 4.14 022/105] Revert "e1000e: fix cyclic resets at link up with active tx"

[Sasha Levin]

From: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>

[ Upstream commit caff422ea81e144842bc44bab408d85ac449377b ]

This reverts commit 0f9e980bf5ee1a97e2e401c846b2af989eb21c61.

That change cased false-positive warning about hardware hang:

e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
e1000e 0000:00:1f.6 eth0: Detected Hardware Unit Hang:
   TDH                  <0>
   TDT                  <1>
   next_to_use          <1>
   next_to_clean        <0>
buffer_info[next_to_clean]:
   time_stamp           <fffba7a7>
   next_to_watch        <0>
   jiffies              <fffbb140>
   next_to_watch.status <0>
MAC Status             <40080080>
PHY Status             <7949>
PHY 1000BASE-T Status  <0>
PHY Extended Status    <3000>
PCI Status             <10>
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx

Besides warning everything works fine.
Original issue will be fixed property in following patch.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203175
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 3c214a47c1c4..5c364321d3c6 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -5306,13 +5306,8 @@ static void e1000_watchdog_task(struct work_struct *work)
 			/* 8000ES2LAN requires a Rx packet buffer work-around
 			 * on link down event; reset the controller to flush
 			 * the Rx packet buffer.
-			 *
-			 * If the link is lost the controller stops DMA, but
-			 * if there is queued Tx work it cannot be done.  So
-			 * reset the controller to flush the Tx packet buffers.
 			 */
-			if ((adapter->flags & FLAG_RX_NEEDS_RESTART) ||
-			    e1000_desc_unused(tx_ring) + 1 < tx_ring->count)
+			if (adapter->flags & FLAG_RX_NEEDS_RESTART)
 				adapter->flags |= FLAG_RESTART_NOW;
 			else
 				pm_schedule_suspend(netdev->dev.parent,
@@ -5335,6 +5330,14 @@ static void e1000_watchdog_task(struct work_struct *work)
 	adapter->gotc_old = adapter->stats.gotc;
 	spin_unlock(&adapter->stats64_lock);
 
+	/* If the link is lost the controller stops DMA, but
+	 * if there is queued Tx work it cannot be done.  So
+	 * reset the controller to flush the Tx packet buffers.
+	 */
+	if (!netif_carrier_ok(netdev) &&
+	    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count))
+		adapter->flags |= FLAG_RESTART_NOW;
+
 	/* If reset is necessary, do it outside of interrupt context. */
 	if (adapter->flags & FLAG_RESTART_NOW) {
 		schedule_work(&adapter->reset_task);
-- 
2.20.1

[PATCH AUTOSEL 4.14 023/105] e1000e: start network tx queue only when link is up

[Sasha Levin]

From: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>

[ Upstream commit d17ba0f616a08f597d9348c372d89b8c0405ccf3 ]

Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.

This patch wakes Tx queue only when NIC is ready to send packets.

This is proper fix for problem addressed by commit 0f9e980bf5ee
("e1000e: fix cyclic resets at link up with active tx").

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/e1000e/netdev.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 5c364321d3c6..1ad345796e80 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4228,7 +4228,7 @@ void e1000e_up(struct e1000_adapter *adapter)
 		e1000_configure_msix(adapter);
 	e1000_irq_enable(adapter);
 
-	netif_start_queue(adapter->netdev);
+	/* Tx queue started by watchdog timer when link is up */
 
 	e1000e_trigger_lsc(adapter);
 }
@@ -4604,6 +4604,7 @@ int e1000e_open(struct net_device *netdev)
 	pm_runtime_get_sync(&pdev->dev);
 
 	netif_carrier_off(netdev);
+	netif_stop_queue(netdev);
 
 	/* allocate transmit descriptors */
 	err = e1000e_setup_tx_resources(adapter->tx_ring);
@@ -4664,7 +4665,6 @@ int e1000e_open(struct net_device *netdev)
 	e1000_irq_enable(adapter);
 
 	adapter->tx_hang_recheck = false;
-	netif_start_queue(netdev);
 
 	hw->mac.get_link_status = true;
 	pm_runtime_put(&pdev->dev);
@@ -5286,6 +5286,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			if (phy->ops.cfg_on_link_up)
 				phy->ops.cfg_on_link_up(hw);
 
+			netif_wake_queue(netdev);
 			netif_carrier_on(netdev);
 
 			if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -5299,6 +5300,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			/* Link status message must follow this format */
 			pr_info("%s NIC Link is Down\n", adapter->netdev->name);
 			netif_carrier_off(netdev);
+			netif_stop_queue(netdev);
 			if (!test_bit(__E1000_DOWN, &adapter->state))
 				mod_timer(&adapter->phy_info_timer,
 					  round_jiffies(jiffies + 2 * HZ));
-- 
2.20.1

[PATCH AUTOSEL 4.14 024/105] media: mc-device.c: don't memset __user pointer contents

[Sasha Levin]

From: Hans Verkuil <hverkuil@xs4all.nl>

[ Upstream commit 518fa4e0e0da97ea2e17c95ab57647ce748a96e2 ]

You can't memset the contents of a __user pointer. Instead, call copy_to_user to
copy links.reserved (which is zeroed) to the user memory.

This fixes this sparse warning:

SPARSE:drivers/media/mc/mc-device.c drivers/media/mc/mc-device.c:521:16:  warning: incorrect type in argument 1 (different address spaces)

Fixes: f49308878d720 ("media: media_device_enum_links32: clean a reserved field")

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/media-device.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/media/media-device.c b/drivers/media/media-device.c
index a6d56154fac7..4eb51a618fe1 100644
--- a/drivers/media/media-device.c
+++ b/drivers/media/media-device.c
@@ -486,8 +486,9 @@ static long media_device_enum_links32(struct media_device *mdev,
 	if (ret)
 		return ret;
 
-	memset(ulinks->reserved, 0, sizeof(ulinks->reserved));
-
+	if (copy_to_user(ulinks->reserved, links.reserved,
+			 sizeof(ulinks->reserved)))
+		return -EFAULT;
 	return 0;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 025/105] media: staging: media: davinci_vpfe: - Fix for memory leak if decoder initialization fails.

[Sasha Levin]

From: Shailendra Verma <shailendra.v@samsung.com>

[ Upstream commit 6995a659101bd4effa41cebb067f9dc18d77520d ]

Fix to avoid possible memory leak if the decoder initialization
got failed.Free the allocated memory for file handle object
before return in case decoder initialization fails.

Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/staging/media/davinci_vpfe/vpfe_video.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/staging/media/davinci_vpfe/vpfe_video.c b/drivers/staging/media/davinci_vpfe/vpfe_video.c
index 155e8c758e4b..346e60d230f3 100644
--- a/drivers/staging/media/davinci_vpfe/vpfe_video.c
+++ b/drivers/staging/media/davinci_vpfe/vpfe_video.c
@@ -422,6 +422,9 @@ static int vpfe_open(struct file *file)
 	/* If decoder is not initialized. initialize it */
 	if (!video->initialized && vpfe_update_pipe_state(video)) {
 		mutex_unlock(&video->lock);
+		v4l2_fh_del(&handle->vfh);
+		v4l2_fh_exit(&handle->vfh);
+		kfree(handle);
 		return -ENODEV;
 	}
 	/* Increment device users counter */
-- 
2.20.1

[PATCH AUTOSEL 4.14 026/105] net: phy: Check against net_device being NULL

[Sasha Levin]

From: Ioana Ciornei <ioana.ciornei@nxp.com>

[ Upstream commit 82c76aca81187b3d28a6fb3062f6916450ce955e ]

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/phy/phy_device.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index c433be573e0d..ed7e3c70b511 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -729,6 +729,9 @@ int phy_connect_direct(struct net_device *dev, struct phy_device *phydev,
 {
 	int rc;
 
+	if (!dev)
+		return -EINVAL;
+
 	rc = phy_attach_direct(dev, phydev, phydev->dev_flags, interface);
 	if (rc)
 		return rc;
@@ -1067,6 +1070,9 @@ struct phy_device *phy_attach(struct net_device *dev, const char *bus_id,
 	struct device *d;
 	int rc;
 
+	if (!dev)
+		return ERR_PTR(-EINVAL);
+
 	/* Search the list of PHY devices on the mdio bus for the
 	 * PHY with the requested name
 	 */
-- 
2.20.1

[PATCH AUTOSEL 4.14 027/105] crypto: talitos - properly handle split ICV.

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit eae55a586c3c8b50982bad3c3426e9c9dd7a0075 ]

The driver assumes that the ICV is as a single piece in the last
element of the scatterlist. This assumption is wrong.

This patch ensures that the ICV is properly handled regardless of
the scatterlist layout.

Fixes: 9c4a79653b35 ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/crypto/talitos.c | 26 +++++++++++++++-----------
 1 file changed, 15 insertions(+), 11 deletions(-)

diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c
index 33fcedeb5f9f..ec9473ddfbb3 100644
--- a/drivers/crypto/talitos.c
+++ b/drivers/crypto/talitos.c
@@ -984,7 +984,6 @@ static void ipsec_esp_encrypt_done(struct device *dev,
 	struct crypto_aead *authenc = crypto_aead_reqtfm(areq);
 	unsigned int authsize = crypto_aead_authsize(authenc);
 	struct talitos_edesc *edesc;
-	struct scatterlist *sg;
 	void *icvdata;
 
 	edesc = container_of(desc, struct talitos_edesc, desc);
@@ -998,9 +997,8 @@ static void ipsec_esp_encrypt_done(struct device *dev,
 		else
 			icvdata = &edesc->link_tbl[edesc->src_nents +
 						   edesc->dst_nents + 2];
-		sg = sg_last(areq->dst, edesc->dst_nents);
-		memcpy((char *)sg_virt(sg) + sg->length - authsize,
-		       icvdata, authsize);
+		sg_pcopy_from_buffer(areq->dst, edesc->dst_nents ? : 1, icvdata,
+				     authsize, areq->assoclen + areq->cryptlen);
 	}
 
 	kfree(edesc);
@@ -1016,7 +1014,6 @@ static void ipsec_esp_decrypt_swauth_done(struct device *dev,
 	struct crypto_aead *authenc = crypto_aead_reqtfm(req);
 	unsigned int authsize = crypto_aead_authsize(authenc);
 	struct talitos_edesc *edesc;
-	struct scatterlist *sg;
 	char *oicv, *icv;
 	struct talitos_private *priv = dev_get_drvdata(dev);
 	bool is_sec1 = has_ftr_sec1(priv);
@@ -1026,9 +1023,18 @@ static void ipsec_esp_decrypt_swauth_done(struct device *dev,
 	ipsec_esp_unmap(dev, edesc, req);
 
 	if (!err) {
+		char icvdata[SHA512_DIGEST_SIZE];
+		int nents = edesc->dst_nents ? : 1;
+		unsigned int len = req->assoclen + req->cryptlen;
+
 		/* auth check */
-		sg = sg_last(req->dst, edesc->dst_nents ? : 1);
-		icv = (char *)sg_virt(sg) + sg->length - authsize;
+		if (nents > 1) {
+			sg_pcopy_to_buffer(req->dst, nents, icvdata, authsize,
+					   len - authsize);
+			icv = icvdata;
+		} else {
+			icv = (char *)sg_virt(req->dst) + len - authsize;
+		}
 
 		if (edesc->dma_len) {
 			if (is_sec1)
@@ -1458,7 +1464,6 @@ static int aead_decrypt(struct aead_request *req)
 	struct talitos_ctx *ctx = crypto_aead_ctx(authenc);
 	struct talitos_private *priv = dev_get_drvdata(ctx->dev);
 	struct talitos_edesc *edesc;
-	struct scatterlist *sg;
 	void *icvdata;
 
 	req->cryptlen -= authsize;
@@ -1493,9 +1498,8 @@ static int aead_decrypt(struct aead_request *req)
 	else
 		icvdata = &edesc->link_tbl[0];
 
-	sg = sg_last(req->src, edesc->src_nents ? : 1);
-
-	memcpy(icvdata, (char *)sg_virt(sg) + sg->length - authsize, authsize);
+	sg_pcopy_to_buffer(req->src, edesc->src_nents ? : 1, icvdata, authsize,
+			   req->assoclen + req->cryptlen - authsize);
 
 	return ipsec_esp(edesc, req, ipsec_esp_decrypt_swauth_done);
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 028/105] crypto: talitos - Align SEC1 accesses to 32 bits boundaries.

[Sasha Levin]

From: Christophe Leroy <christophe.leroy@c-s.fr>

[ Upstream commit c9cca7034b34a2d82e9a03b757de2485c294851c ]

The MPC885 reference manual states:

SEC Lite-initiated 8xx writes can occur only on 32-bit-word boundaries, but
reads can occur on any byte boundary. Writing back a header read from a
non-32-bit-word boundary will yield unpredictable results.

In order to ensure that, cra_alignmask is set to 3 for SEC1.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9c4a79653b35 ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/crypto/talitos.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/crypto/talitos.c b/drivers/crypto/talitos.c
index ec9473ddfbb3..9f79ad57a5a5 100644
--- a/drivers/crypto/talitos.c
+++ b/drivers/crypto/talitos.c
@@ -3119,7 +3119,10 @@ static struct talitos_crypto_alg *talitos_alg_alloc(struct device *dev,
 		alg->cra_priority = t_alg->algt.priority;
 	else
 		alg->cra_priority = TALITOS_CRA_PRIORITY;
-	alg->cra_alignmask = 0;
+	if (has_ftr_sec1(priv))
+		alg->cra_alignmask = 3;
+	else
+		alg->cra_alignmask = 0;
 	alg->cra_ctxsize = sizeof(struct talitos_ctx);
 	alg->cra_flags |= CRYPTO_ALG_KERN_DRIVER_ONLY;
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 029/105] tua6100: Avoid build warnings.

[Sasha Levin]

From: "David S. Miller" <davem@davemloft.net>

[ Upstream commit 621ccc6cc5f8d6730b740d31d4818227866c93c9 ]

Rename _P to _P_VAL and _R to _R_VAL to avoid global
namespace conflicts:

drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’:
drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined
 #define _P 32

In file included from ./include/acpi/platform/aclinux.h:54,
                 from ./include/acpi/platform/acenv.h:152,
                 from ./include/acpi/acpi.h:22,
                 from ./include/linux/acpi.h:34,
                 from ./include/linux/i2c.h:17,
                 from drivers/media/dvb-frontends/tua6100.h:30,
                 from drivers/media/dvb-frontends/tua6100.c:32:
./include/linux/ctype.h:14: note: this is the location of the previous definition
 #define _P 0x10 /* punct */

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/dvb-frontends/tua6100.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/media/dvb-frontends/tua6100.c b/drivers/media/dvb-frontends/tua6100.c
index 18e6d4c5be21..859fa14b319c 100644
--- a/drivers/media/dvb-frontends/tua6100.c
+++ b/drivers/media/dvb-frontends/tua6100.c
@@ -75,8 +75,8 @@ static int tua6100_set_params(struct dvb_frontend *fe)
 	struct i2c_msg msg1 = { .addr = priv->i2c_address, .flags = 0, .buf = reg1, .len = 4 };
 	struct i2c_msg msg2 = { .addr = priv->i2c_address, .flags = 0, .buf = reg2, .len = 3 };
 
-#define _R 4
-#define _P 32
+#define _R_VAL 4
+#define _P_VAL 32
 #define _ri 4000000
 
 	// setup register 0
@@ -91,14 +91,14 @@ static int tua6100_set_params(struct dvb_frontend *fe)
 	else
 		reg1[1] = 0x0c;
 
-	if (_P == 64)
+	if (_P_VAL == 64)
 		reg1[1] |= 0x40;
 	if (c->frequency >= 1525000)
 		reg1[1] |= 0x80;
 
 	// register 2
-	reg2[1] = (_R >> 8) & 0x03;
-	reg2[2] = _R;
+	reg2[1] = (_R_VAL >> 8) & 0x03;
+	reg2[2] = _R_VAL;
 	if (c->frequency < 1455000)
 		reg2[1] |= 0x1c;
 	else if (c->frequency < 1630000)
@@ -110,18 +110,18 @@ static int tua6100_set_params(struct dvb_frontend *fe)
 	 * The N divisor ratio (note: c->frequency is in kHz, but we
 	 * need it in Hz)
 	 */
-	prediv = (c->frequency * _R) / (_ri / 1000);
-	div = prediv / _P;
+	prediv = (c->frequency * _R_VAL) / (_ri / 1000);
+	div = prediv / _P_VAL;
 	reg1[1] |= (div >> 9) & 0x03;
 	reg1[2] = div >> 1;
 	reg1[3] = (div << 7);
-	priv->frequency = ((div * _P) * (_ri / 1000)) / _R;
+	priv->frequency = ((div * _P_VAL) * (_ri / 1000)) / _R_VAL;
 
 	// Finally, calculate and store the value for A
-	reg1[3] |= (prediv - (div*_P)) & 0x7f;
+	reg1[3] |= (prediv - (div*_P_VAL)) & 0x7f;
 
-#undef _R
-#undef _P
+#undef _R_VAL
+#undef _P_VAL
 #undef _ri
 
 	if (fe->ops.i2c_gate_ctrl)
-- 
2.20.1

[PATCH AUTOSEL 4.14 030/105] locking/lockdep: Fix merging of hlocks with non-zero references

[Sasha Levin]

From: Imre Deak <imre.deak@intel.com>

[ Upstream commit d9349850e188b8b59e5322fda17ff389a1c0cd7d ]

The sequence

	static DEFINE_WW_CLASS(test_ww_class);

	struct ww_acquire_ctx ww_ctx;
	struct ww_mutex ww_lock_a;
	struct ww_mutex ww_lock_b;
	struct ww_mutex ww_lock_c;
	struct mutex lock_c;

	ww_acquire_init(&ww_ctx, &test_ww_class);

	ww_mutex_init(&ww_lock_a, &test_ww_class);
	ww_mutex_init(&ww_lock_b, &test_ww_class);
	ww_mutex_init(&ww_lock_c, &test_ww_class);

	mutex_init(&lock_c);

	ww_mutex_lock(&ww_lock_a, &ww_ctx);

	mutex_lock(&lock_c);

	ww_mutex_lock(&ww_lock_b, &ww_ctx);
	ww_mutex_lock(&ww_lock_c, &ww_ctx);

	mutex_unlock(&lock_c);	(*)

	ww_mutex_unlock(&ww_lock_c);
	ww_mutex_unlock(&ww_lock_b);
	ww_mutex_unlock(&ww_lock_a);

	ww_acquire_fini(&ww_ctx); (**)

will trigger the following error in __lock_release() when calling
mutex_release() at **:

	DEBUG_LOCKS_WARN_ON(depth <= 0)

The problem is that the hlock merging happening at * updates the
references for test_ww_class incorrectly to 3 whereas it should've
updated it to 4 (representing all the instances for ww_ctx and
ww_lock_[abc]).

Fix this by updating the references during merging correctly taking into
account that we can have non-zero references (both for the hlock that we
merge into another hlock or for the hlock we are merging into).

Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: =?UTF-8?q?Ville=20Syrj=C3=A4l=C3=A4?= <ville.syrjala@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/20190524201509.9199-2-imre.deak@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/locking/lockdep.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/kernel/locking/lockdep.c b/kernel/locking/lockdep.c
index bf694c709b96..565005a3b8f0 100644
--- a/kernel/locking/lockdep.c
+++ b/kernel/locking/lockdep.c
@@ -3402,17 +3402,17 @@ static int __lock_acquire(struct lockdep_map *lock, unsigned int subclass,
 	if (depth && !cross_lock(lock)) {
 		hlock = curr->held_locks + depth - 1;
 		if (hlock->class_idx == class_idx && nest_lock) {
-			if (hlock->references) {
-				/*
-				 * Check: unsigned int references:12, overflow.
-				 */
-				if (DEBUG_LOCKS_WARN_ON(hlock->references == (1 << 12)-1))
-					return 0;
+			if (!references)
+				references++;
 
+			if (!hlock->references)
 				hlock->references++;
-			} else {
-				hlock->references = 2;
-			}
+
+			hlock->references += references;
+
+			/* Overflow */
+			if (DEBUG_LOCKS_WARN_ON(hlock->references < references))
+				return 0;
 
 			return 1;
 		}
-- 
2.20.1

[PATCH AUTOSEL 4.14 031/105] media: wl128x: Fix some error handling in fm_v4l2_init_video_device()

[Sasha Levin]

From: Kefeng Wang <wangkefeng.wang@huawei.com>

[ Upstream commit 69fbb3f47327d959830c94bf31893972b8c8f700 ]

X-Originating-IP: [10.175.113.25]
X-CFilter-Loop: Reflected
The fm_v4l2_init_video_device() forget to unregister v4l2/video device
in the error path, it could lead to UAF issue, eg,

  BUG: KASAN: use-after-free in atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline]
  BUG: KASAN: use-after-free in atomic_long_read include/asm-generic/atomic-long.h:28 [inline]
  BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206
  Read of size 8 at addr ffff8881e84a7c70 by task v4l_id/3659

  CPU: 1 PID: 3659 Comm: v4l_id Not tainted 5.1.0 #8
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
  Call Trace:
   __dump_stack lib/dump_stack.c:77 [inline]
   dump_stack+0xa9/0x10e lib/dump_stack.c:113
   print_address_description+0x65/0x270 mm/kasan/report.c:187
   kasan_report+0x149/0x18d mm/kasan/report.c:317
   atomic64_read include/asm-generic/atomic-instrumented.h:836 [inline]
   atomic_long_read include/asm-generic/atomic-long.h:28 [inline]
   __mutex_unlock_slowpath+0x92/0x690 kernel/locking/mutex.c:1206
   fm_v4l2_fops_open+0xac/0x120 [fm_drv]
   v4l2_open+0x191/0x390 [videodev]
   chrdev_open+0x20d/0x570 fs/char_dev.c:417
   do_dentry_open+0x700/0xf30 fs/open.c:777
   do_last fs/namei.c:3416 [inline]
   path_openat+0x7c4/0x2a90 fs/namei.c:3532
   do_filp_open+0x1a5/0x2b0 fs/namei.c:3563
   do_sys_open+0x302/0x490 fs/open.c:1069
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7f8180c17c8e
  ...
  Allocated by task 3642:
   set_track mm/kasan/common.c:87 [inline]
   __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:497
   fm_drv_init+0x13/0x1000 [fm_drv]
   do_one_initcall+0xbc/0x47d init/main.c:901
   do_init_module+0x1b5/0x547 kernel/module.c:3456
   load_module+0x6405/0x8c10 kernel/module.c:3804
   __do_sys_finit_module+0x162/0x190 kernel/module.c:3898
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

  Freed by task 3642:
   set_track mm/kasan/common.c:87 [inline]
   __kasan_slab_free+0x130/0x180 mm/kasan/common.c:459
   slab_free_hook mm/slub.c:1429 [inline]
   slab_free_freelist_hook mm/slub.c:1456 [inline]
   slab_free mm/slub.c:3003 [inline]
   kfree+0xe1/0x270 mm/slub.c:3958
   fm_drv_init+0x1e6/0x1000 [fm_drv]
   do_one_initcall+0xbc/0x47d init/main.c:901
   do_init_module+0x1b5/0x547 kernel/module.c:3456
   load_module+0x6405/0x8c10 kernel/module.c:3804
   __do_sys_finit_module+0x162/0x190 kernel/module.c:3898
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe

Add relevant unregister functions to fix it.

Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/radio/wl128x/fmdrv_v4l2.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/media/radio/wl128x/fmdrv_v4l2.c b/drivers/media/radio/wl128x/fmdrv_v4l2.c
index fc5a7abc83d2..77778c86e04d 100644
--- a/drivers/media/radio/wl128x/fmdrv_v4l2.c
+++ b/drivers/media/radio/wl128x/fmdrv_v4l2.c
@@ -549,6 +549,7 @@ int fm_v4l2_init_video_device(struct fmdev *fmdev, int radio_nr)
 
 	/* Register with V4L2 subsystem as RADIO device */
 	if (video_register_device(&gradio_dev, VFL_TYPE_RADIO, radio_nr)) {
+		v4l2_device_unregister(&fmdev->v4l2_dev);
 		fmerr("Could not register video device\n");
 		return -ENOMEM;
 	}
@@ -562,6 +563,8 @@ int fm_v4l2_init_video_device(struct fmdev *fmdev, int radio_nr)
 	if (ret < 0) {
 		fmerr("(fmdev): Can't init ctrl handler\n");
 		v4l2_ctrl_handler_free(&fmdev->ctrl_handler);
+		video_unregister_device(fmdev->radio_dev);
+		v4l2_device_unregister(&fmdev->v4l2_dev);
 		return -EBUSY;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 032/105] cpupower : frequency-set -r option misses the last cpu in related cpu list

[Sasha Levin]

From: Abhishek Goel <huntbag@linux.vnet.ibm.com>

[ Upstream commit 04507c0a9385cc8280f794a36bfff567c8cc1042 ]

To set frequency on specific cpus using cpupower, following syntax can
be used :
cpupower -c #i frequency-set -f #f -r

While setting frequency using cpupower frequency-set command, if we use
'-r' option, it is expected to set frequency for all cpus related to
cpu #i. But it is observed to be missing the last cpu in related cpu
list. This patch fixes the problem.

Signed-off-by: Abhishek Goel <huntbag@linux.vnet.ibm.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/power/cpupower/utils/cpufreq-set.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/tools/power/cpupower/utils/cpufreq-set.c b/tools/power/cpupower/utils/cpufreq-set.c
index 1eef0aed6423..08a405593a79 100644
--- a/tools/power/cpupower/utils/cpufreq-set.c
+++ b/tools/power/cpupower/utils/cpufreq-set.c
@@ -306,6 +306,8 @@ int cmd_freq_set(int argc, char **argv)
 				bitmask_setbit(cpus_chosen, cpus->cpu);
 				cpus = cpus->next;
 			}
+			/* Set the last cpu in related cpus list */
+			bitmask_setbit(cpus_chosen, cpus->cpu);
 			cpufreq_put_related_cpus(cpus);
 		}
 	}
-- 
2.20.1

[PATCH AUTOSEL 4.14 033/105] net: stmmac: dwmac4: fix flow control issue

[Sasha Levin]

From: Biao Huang <biao.huang@mediatek.com>

[ Upstream commit ee326fd01e79dfa42014d55931260b68b9fa3273 ]

Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.

Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
index ed5fcd4994f2..8445af580cb6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
@@ -474,8 +474,9 @@ static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,
 	if (fc & FLOW_RX) {
 		pr_debug("\tReceive Flow-Control ON\n");
 		flow |= GMAC_RX_FLOW_CTRL_RFE;
-		writel(flow, ioaddr + GMAC_RX_FLOW_CTRL);
 	}
+	writel(flow, ioaddr + GMAC_RX_FLOW_CTRL);
+
 	if (fc & FLOW_TX) {
 		pr_debug("\tTransmit Flow-Control ON\n");
 
@@ -483,7 +484,7 @@ static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,
 			pr_debug("\tduplex mode: PAUSE %d\n", pause_time);
 
 		for (queue = 0; queue < tx_cnt; queue++) {
-			flow |= GMAC_TX_FLOW_CTRL_TFE;
+			flow = GMAC_TX_FLOW_CTRL_TFE;
 
 			if (duplex)
 				flow |=
@@ -491,6 +492,9 @@ static void dwmac4_flow_ctrl(struct mac_device_info *hw, unsigned int duplex,
 
 			writel(flow, ioaddr + GMAC_QX_TX_FLOW_CTRL(queue));
 		}
+	} else {
+		for (queue = 0; queue < tx_cnt; queue++)
+			writel(0, ioaddr + GMAC_QX_TX_FLOW_CTRL(queue));
 	}
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 034/105] net: fec: Do not use netdev messages too early

[Sasha Levin]

From: Fabio Estevam <festevam@gmail.com>

[ Upstream commit a19a0582363b9a5f8ba812f34f1b8df394898780 ]

When a valid MAC address is not found the current messages
are shown:

fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa

Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:

fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa

Tested on a imx6dl-pico-pi board.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/freescale/fec_main.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 98cd53d380f7..0ae6532b02e0 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1690,10 +1690,10 @@ static void fec_get_mac(struct net_device *ndev)
 	 */
 	if (!is_valid_ether_addr(iap)) {
 		/* Report it and use a random ethernet address instead */
-		netdev_err(ndev, "Invalid MAC address: %pM\n", iap);
+		dev_err(&fep->pdev->dev, "Invalid MAC address: %pM\n", iap);
 		eth_hw_addr_random(ndev);
-		netdev_info(ndev, "Using random MAC address: %pM\n",
-			    ndev->dev_addr);
+		dev_info(&fep->pdev->dev, "Using random MAC address: %pM\n",
+			 ndev->dev_addr);
 		return;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 035/105] net: axienet: Fix race condition causing TX hang

[Sasha Levin]

From: Robert Hancock <hancock@sedsystems.ca>

[ Upstream commit 7de44285c1f69ccfbe8be1d6a16fcd956681fee6 ]

It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.

To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.

Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/ethernet/xilinx/xilinx_axienet_main.c | 20 ++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index d46dc8cd1670..b481cb174b23 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -614,6 +614,10 @@ static void axienet_start_xmit_done(struct net_device *ndev)
 
 	ndev->stats.tx_packets += packets;
 	ndev->stats.tx_bytes += size;
+
+	/* Matches barrier in axienet_start_xmit */
+	smp_mb();
+
 	netif_wake_queue(ndev);
 }
 
@@ -668,9 +672,19 @@ static int axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
 	cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
 
 	if (axienet_check_tx_bd_space(lp, num_frag)) {
-		if (!netif_queue_stopped(ndev))
-			netif_stop_queue(ndev);
-		return NETDEV_TX_BUSY;
+		if (netif_queue_stopped(ndev))
+			return NETDEV_TX_BUSY;
+
+		netif_stop_queue(ndev);
+
+		/* Matches barrier in axienet_start_xmit_done */
+		smp_mb();
+
+		/* Space might have just been freed - check again */
+		if (axienet_check_tx_bd_space(lp, num_frag))
+			return NETDEV_TX_BUSY;
+
+		netif_wake_queue(ndev);
 	}
 
 	if (skb->ip_summed == CHECKSUM_PARTIAL) {
-- 
2.20.1

[PATCH AUTOSEL 4.14 036/105] s390/qdio: handle PENDING state for QEBSM devices

[Sasha Levin]

From: Julian Wiedmann <jwi@linux.ibm.com>

[ Upstream commit 04310324c6f482921c071444833e70fe861b73d9 ]

When a CQ-enabled device uses QEBSM for SBAL state inspection,
get_buf_states() can return the PENDING state for an Output Queue.
get_outbound_buffer_frontier() isn't prepared for this, and any PENDING
buffer will permanently stall all further completion processing on this
Queue.

This isn't a concern for non-QEBSM devices, as get_buf_states() for such
devices will manually turn PENDING buffers into EMPTY ones.

Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/s390/cio/qdio_main.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/s390/cio/qdio_main.c b/drivers/s390/cio/qdio_main.c
index c7afdbded26b..ab8dd81fbc2b 100644
--- a/drivers/s390/cio/qdio_main.c
+++ b/drivers/s390/cio/qdio_main.c
@@ -759,6 +759,7 @@ static int get_outbound_buffer_frontier(struct qdio_q *q)
 
 	switch (state) {
 	case SLSB_P_OUTPUT_EMPTY:
+	case SLSB_P_OUTPUT_PENDING:
 		/* the adapter got it */
 		DBF_DEV_EVENT(DBF_INFO, q->irq_ptr,
 			"out empty:%1d %02x", q->nr, count);
-- 
2.20.1

[PATCH AUTOSEL 4.14 037/105] RAS/CEC: Fix pfn insertion

[Sasha Levin]

From: Borislav Petkov <bp@suse.de>

[ Upstream commit 6d8e294bf5f0e85c34e8b14b064e2965f53f38b0 ]

When inserting random PFNs for debugging the CEC through
(debugfs)/ras/cec/pfn, depending on the return value of pfn_set(),
multiple values get inserted per a single write.

That is because simple_attr_write() interprets a retval of 0 as
success and claims the whole input. However, pfn_set() returns the
cec_add_elem() value, which, if > 0 and smaller than the whole input
length, makes glibc continue issuing the write syscall until there's
input left:

  pfn_set
  simple_attr_write
  debugfs_attr_write
  full_proxy_write
  vfs_write
  ksys_write
  do_syscall_64
  entry_SYSCALL_64_after_hwframe

leading to those repeated calls.

Return 0 to fix that.

Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/ras/cec.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/ras/cec.c b/drivers/ras/cec.c
index c7205cdcc11a..97cf40a522be 100644
--- a/drivers/ras/cec.c
+++ b/drivers/ras/cec.c
@@ -373,7 +373,9 @@ static int pfn_set(void *data, u64 val)
 {
 	*(u64 *)data = val;
 
-	return cec_add_elem(val);
+	cec_add_elem(val);
+
+	return 0;
 }
 
 DEFINE_DEBUGFS_ATTRIBUTE(pfn_ops, u64_get, pfn_set, "0x%llx\n");
-- 
2.20.1

[PATCH AUTOSEL 4.14 038/105] net: sfp: add mutex to prevent concurrent state checks

[Sasha Levin]

From: Robert Hancock <hancock@sedsystems.ca>

[ Upstream commit 2158e856f56bb762ef90f3ec244d41a519826f75 ]

sfp_check_state can potentially be called by both a threaded IRQ handler
and delayed work. If it is concurrently called, it could result in
incorrect state management. Add a st_mutex to protect the state - this
lock gets taken outside of code that checks and handle state changes, and
the existing sm_mutex nests inside of it.

Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/phy/sfp.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c
index 2dcb25aa0452..9cef89fe410d 100644
--- a/drivers/net/phy/sfp.c
+++ b/drivers/net/phy/sfp.c
@@ -115,10 +115,11 @@ struct sfp {
 	struct gpio_desc *gpio[GPIO_MAX];
 
 	bool attached;
+	struct mutex st_mutex;			/* Protects state */
 	unsigned int state;
 	struct delayed_work poll;
 	struct delayed_work timeout;
-	struct mutex sm_mutex;
+	struct mutex sm_mutex;			/* Protects state machine */
 	unsigned char sm_mod_state;
 	unsigned char sm_dev_state;
 	unsigned short sm_state;
@@ -738,6 +739,7 @@ static void sfp_check_state(struct sfp *sfp)
 {
 	unsigned int state, i, changed;
 
+	mutex_lock(&sfp->st_mutex);
 	state = sfp_get_state(sfp);
 	changed = state ^ sfp->state;
 	changed &= SFP_F_PRESENT | SFP_F_LOS | SFP_F_TX_FAULT;
@@ -763,6 +765,7 @@ static void sfp_check_state(struct sfp *sfp)
 		sfp_sm_event(sfp, state & SFP_F_LOS ?
 				SFP_E_LOS_HIGH : SFP_E_LOS_LOW);
 	rtnl_unlock();
+	mutex_unlock(&sfp->st_mutex);
 }
 
 static irqreturn_t sfp_irq(int irq, void *data)
@@ -793,6 +796,7 @@ static struct sfp *sfp_alloc(struct device *dev)
 	sfp->dev = dev;
 
 	mutex_init(&sfp->sm_mutex);
+	mutex_init(&sfp->st_mutex);
 	INIT_DELAYED_WORK(&sfp->poll, sfp_poll);
 	INIT_DELAYED_WORK(&sfp->timeout, sfp_timeout);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 039/105] ipset: Fix memory accounting for hash types on resize

[Sasha Levin]

From: Stefano Brivio <sbrivio@redhat.com>

[ Upstream commit 11921796f4799ca9c61c4b22cc54d84aa69f8a35 ]

If a fresh array block is allocated during resize, the current in-memory
set size should be increased by the size of the block, not replaced by it.

Before the fix, adding entries to a hash set type, leading to a table
resize, caused an inconsistent memory size to be reported. This becomes
more obvious when swapping sets with similar sizes:

  # cat hash_ip_size.sh
  #!/bin/sh
  FAIL_RETRIES=10

  tries=0
  while [ ${tries} -lt ${FAIL_RETRIES} ]; do
  	ipset create t1 hash:ip
  	for i in `seq 1 4345`; do
  		ipset add t1 1.2.$((i / 255)).$((i % 255))
  	done
  	t1_init="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"

  	ipset create t2 hash:ip
  	for i in `seq 1 4360`; do
  		ipset add t2 1.2.$((i / 255)).$((i % 255))
  	done
  	t2_init="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"

  	ipset swap t1 t2
  	t1_swap="$(ipset list t1|sed -n 's/Size in memory: \(.*\)/\1/p')"
  	t2_swap="$(ipset list t2|sed -n 's/Size in memory: \(.*\)/\1/p')"

  	ipset destroy t1
  	ipset destroy t2
  	tries=$((tries + 1))

  	if [ ${t1_init} -lt 10000 ] || [ ${t2_init} -lt 10000 ]; then
  		echo "FAIL after ${tries} tries:"
  		echo "T1 size ${t1_init}, after swap ${t1_swap}"
  		echo "T2 size ${t2_init}, after swap ${t2_swap}"
  		exit 1
  	fi
  done
  echo "PASS"
  # echo -n 'func hash_ip4_resize +p' > /sys/kernel/debug/dynamic_debug/control
  # ./hash_ip_size.sh
  [ 2035.018673] attempt to resize set t1 from 10 to 11, t 00000000fe6551fa
  [ 2035.078583] set t1 resized from 10 (00000000fe6551fa) to 11 (00000000172a0163)
  [ 2035.080353] Table destroy by resize 00000000fe6551fa
  FAIL after 4 tries:
  T1 size 9064, after swap 71128
  T2 size 71128, after swap 9064

Reported-by: NOYB <JunkYardMail1@Frontier.com>
Fixes: 9e41f26a505c ("netfilter: ipset: Count non-static extension memory for userspace")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/ipset/ip_set_hash_gen.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netfilter/ipset/ip_set_hash_gen.h b/net/netfilter/ipset/ip_set_hash_gen.h
index dfd268166e42..42d9cd22447e 100644
--- a/net/netfilter/ipset/ip_set_hash_gen.h
+++ b/net/netfilter/ipset/ip_set_hash_gen.h
@@ -624,7 +624,7 @@ mtype_resize(struct ip_set *set, bool retried)
 					goto cleanup;
 				}
 				m->size = AHASH_INIT_SIZE;
-				extsize = ext_size(AHASH_INIT_SIZE, dsize);
+				extsize += ext_size(AHASH_INIT_SIZE, dsize);
 				RCU_INIT_POINTER(hbucket(t, key), m);
 			} else if (m->pos >= m->size) {
 				struct hbucket *ht;
-- 
2.20.1

[PATCH AUTOSEL 4.14 040/105] perf cs-etm: Properly set the value of 'old' and 'head' in snapshot mode

[Sasha Levin]

From: Mathieu Poirier <mathieu.poirier@linaro.org>

[ Upstream commit e45c48a9a4d20ebc7b639a62c3ef8f4b08007027 ]

This patch adds the necessary intelligence to properly compute the value
of 'old' and 'head' when operating in snapshot mode.  That way we can
get the latest information in the AUX buffer and be compatible with the
generic AUX ring buffer mechanic.

Tester notes:

> Leo, have you had the chance to test/review this one? Suzuki?

Sure.  I applied this patch on the perf/core branch (with latest
commit 3e4fbf36c1e3 'perf augmented_raw_syscalls: Move reading
filename to the loop') and passed testing with below steps:

  # perf record -e cs_etm/@tmc_etr0/ -S -m,64 --per-thread ./sort &
  [1] 19097
  Bubble sorting array of 30000 elements

  # kill -USR2 19097
  # kill -USR2 19097
  # kill -USR2 19097
  [ perf record: Woken up 4 times to write data ]
  [ perf record: Captured and wrote 0.753 MB perf.data ]

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20190605161633.12245-1-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/perf/arch/arm/util/cs-etm.c | 127 +++++++++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 4 deletions(-)

diff --git a/tools/perf/arch/arm/util/cs-etm.c b/tools/perf/arch/arm/util/cs-etm.c
index fbfc055d3f4d..aec62e822bab 100644
--- a/tools/perf/arch/arm/util/cs-etm.c
+++ b/tools/perf/arch/arm/util/cs-etm.c
@@ -43,6 +43,8 @@ struct cs_etm_recording {
 	struct auxtrace_record	itr;
 	struct perf_pmu		*cs_etm_pmu;
 	struct perf_evlist	*evlist;
+	int			wrapped_cnt;
+	bool			*wrapped;
 	bool			snapshot_mode;
 	size_t			snapshot_size;
 };
@@ -485,16 +487,131 @@ static int cs_etm_info_fill(struct auxtrace_record *itr,
 	return 0;
 }
 
-static int cs_etm_find_snapshot(struct auxtrace_record *itr __maybe_unused,
+static int cs_etm_alloc_wrapped_array(struct cs_etm_recording *ptr, int idx)
+{
+	bool *wrapped;
+	int cnt = ptr->wrapped_cnt;
+
+	/* Make @ptr->wrapped as big as @idx */
+	while (cnt <= idx)
+		cnt++;
+
+	/*
+	 * Free'ed in cs_etm_recording_free().  Using realloc() to avoid
+	 * cross compilation problems where the host's system supports
+	 * reallocarray() but not the target.
+	 */
+	wrapped = realloc(ptr->wrapped, cnt * sizeof(bool));
+	if (!wrapped)
+		return -ENOMEM;
+
+	wrapped[cnt - 1] = false;
+	ptr->wrapped_cnt = cnt;
+	ptr->wrapped = wrapped;
+
+	return 0;
+}
+
+static bool cs_etm_buffer_has_wrapped(unsigned char *buffer,
+				      size_t buffer_size, u64 head)
+{
+	u64 i, watermark;
+	u64 *buf = (u64 *)buffer;
+	size_t buf_size = buffer_size;
+
+	/*
+	 * We want to look the very last 512 byte (chosen arbitrarily) in
+	 * the ring buffer.
+	 */
+	watermark = buf_size - 512;
+
+	/*
+	 * @head is continuously increasing - if its value is equal or greater
+	 * than the size of the ring buffer, it has wrapped around.
+	 */
+	if (head >= buffer_size)
+		return true;
+
+	/*
+	 * The value of @head is somewhere within the size of the ring buffer.
+	 * This can be that there hasn't been enough data to fill the ring
+	 * buffer yet or the trace time was so long that @head has numerically
+	 * wrapped around.  To find we need to check if we have data at the very
+	 * end of the ring buffer.  We can reliably do this because mmap'ed
+	 * pages are zeroed out and there is a fresh mapping with every new
+	 * session.
+	 */
+
+	/* @head is less than 512 byte from the end of the ring buffer */
+	if (head > watermark)
+		watermark = head;
+
+	/*
+	 * Speed things up by using 64 bit transactions (see "u64 *buf" above)
+	 */
+	watermark >>= 3;
+	buf_size >>= 3;
+
+	/*
+	 * If we find trace data at the end of the ring buffer, @head has
+	 * been there and has numerically wrapped around at least once.
+	 */
+	for (i = watermark; i < buf_size; i++)
+		if (buf[i])
+			return true;
+
+	return false;
+}
+
+static int cs_etm_find_snapshot(struct auxtrace_record *itr,
 				int idx, struct auxtrace_mmap *mm,
-				unsigned char *data __maybe_unused,
+				unsigned char *data,
 				u64 *head, u64 *old)
 {
+	int err;
+	bool wrapped;
+	struct cs_etm_recording *ptr =
+			container_of(itr, struct cs_etm_recording, itr);
+
+	/*
+	 * Allocate memory to keep track of wrapping if this is the first
+	 * time we deal with this *mm.
+	 */
+	if (idx >= ptr->wrapped_cnt) {
+		err = cs_etm_alloc_wrapped_array(ptr, idx);
+		if (err)
+			return err;
+	}
+
+	/*
+	 * Check to see if *head has wrapped around.  If it hasn't only the
+	 * amount of data between *head and *old is snapshot'ed to avoid
+	 * bloating the perf.data file with zeros.  But as soon as *head has
+	 * wrapped around the entire size of the AUX ring buffer it taken.
+	 */
+	wrapped = ptr->wrapped[idx];
+	if (!wrapped && cs_etm_buffer_has_wrapped(data, mm->len, *head)) {
+		wrapped = true;
+		ptr->wrapped[idx] = true;
+	}
+
 	pr_debug3("%s: mmap index %d old head %zu new head %zu size %zu\n",
 		  __func__, idx, (size_t)*old, (size_t)*head, mm->len);
 
-	*old = *head;
-	*head += mm->len;
+	/* No wrap has occurred, we can just use *head and *old. */
+	if (!wrapped)
+		return 0;
+
+	/*
+	 * *head has wrapped around - adjust *head and *old to pickup the
+	 * entire content of the AUX buffer.
+	 */
+	if (*head >= mm->len) {
+		*old = *head - mm->len;
+	} else {
+		*head += mm->len;
+		*old = *head - mm->len;
+	}
 
 	return 0;
 }
@@ -535,6 +652,8 @@ static void cs_etm_recording_free(struct auxtrace_record *itr)
 {
 	struct cs_etm_recording *ptr =
 			container_of(itr, struct cs_etm_recording, itr);
+
+	zfree(&ptr->wrapped);
 	free(ptr);
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 041/105] perf test 6: Fix missing kvm module load for s390

[Sasha Levin]

From: Thomas Richter <tmricht@linux.ibm.com>

[ Upstream commit 53fe307dfd309e425b171f6272d64296a54f4dff ]

Command

   # perf test -Fv 6

fails with error

   running test 100 'kvm-s390:kvm_s390_create_vm' failed to parse
    event 'kvm-s390:kvm_s390_create_vm', err -1, str 'unknown tracepoint'
    event syntax error: 'kvm-s390:kvm_s390_create_vm'
                         \___ unknown tracepoint

when the kvm module is not loaded or not built in.

Fix this by adding a valid function which tests if the module
is loaded. Loaded modules (or builtin KVM support) have a
directory named
  /sys/kernel/debug/tracing/events/kvm-s390
for this tracepoint.

Check for existence of this directory.

Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20190604053504.43073-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/perf/tests/parse-events.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/tools/perf/tests/parse-events.c b/tools/perf/tests/parse-events.c
index f0679613bd18..424b82a7d078 100644
--- a/tools/perf/tests/parse-events.c
+++ b/tools/perf/tests/parse-events.c
@@ -19,6 +19,32 @@
 #define PERF_TP_SAMPLE_TYPE (PERF_SAMPLE_RAW | PERF_SAMPLE_TIME | \
 			     PERF_SAMPLE_CPU | PERF_SAMPLE_PERIOD)
 
+#if defined(__s390x__)
+/* Return true if kvm module is available and loaded. Test this
+ * and retun success when trace point kvm_s390_create_vm
+ * exists. Otherwise this test always fails.
+ */
+static bool kvm_s390_create_vm_valid(void)
+{
+	char *eventfile;
+	bool rc = false;
+
+	eventfile = get_events_file("kvm-s390");
+
+	if (eventfile) {
+		DIR *mydir = opendir(eventfile);
+
+		if (mydir) {
+			rc = true;
+			closedir(mydir);
+		}
+		put_events_file(eventfile);
+	}
+
+	return rc;
+}
+#endif
+
 static int test__checkevent_tracepoint(struct perf_evlist *evlist)
 {
 	struct perf_evsel *evsel = perf_evlist__first(evlist);
@@ -1600,6 +1626,7 @@ static struct evlist_test test__events[] = {
 	{
 		.name  = "kvm-s390:kvm_s390_create_vm",
 		.check = test__checkevent_tracepoint,
+		.valid = kvm_s390_create_vm_valid,
 		.id    = 100,
 	},
 #endif
-- 
2.20.1

[PATCH AUTOSEL 4.14 042/105] media: fdp1: Support M3N and E3 platforms

[Sasha Levin]

From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

[ Upstream commit 4e8c120de9268fc26f583268b9d22e7d37c4595f ]

New Gen3 R-Car platforms incorporate the FDP1 with an updated version
register. No code change is required to support these targets, but they
will currently report an error stating that the device can not be
identified.

Update the driver to match against the new device types.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/rcar_fdp1.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/media/platform/rcar_fdp1.c b/drivers/media/platform/rcar_fdp1.c
index 3245bc45f4a0..a889332d5d30 100644
--- a/drivers/media/platform/rcar_fdp1.c
+++ b/drivers/media/platform/rcar_fdp1.c
@@ -261,6 +261,8 @@ MODULE_PARM_DESC(debug, "activate debug info");
 #define FD1_IP_H3_ES1			0x02010101
 #define FD1_IP_M3W			0x02010202
 #define FD1_IP_H3			0x02010203
+#define FD1_IP_M3N			0x02010204
+#define FD1_IP_E3			0x02010205
 
 /* LUTs */
 #define FD1_LUT_DIF_ADJ			0x1000
@@ -2369,6 +2371,12 @@ static int fdp1_probe(struct platform_device *pdev)
 	case FD1_IP_H3:
 		dprintk(fdp1, "FDP1 Version R-Car H3\n");
 		break;
+	case FD1_IP_M3N:
+		dprintk(fdp1, "FDP1 Version R-Car M3N\n");
+		break;
+	case FD1_IP_E3:
+		dprintk(fdp1, "FDP1 Version R-Car E3\n");
+		break;
 	default:
 		dev_err(fdp1->dev, "FDP1 Unidentifiable (0x%08x)\n",
 				hw_version);
-- 
2.20.1

[PATCH AUTOSEL 4.14 043/105] iommu: Fix a leak in iommu_insert_resv_region

[Sasha Levin]

From: Eric Auger <eric.auger@redhat.com>

[ Upstream commit ad0834dedaa15c3a176f783c0373f836e44b4700 ]

In case we expand an existing region, we unlink
this latter and insert the larger one. In
that case we should free the original region after
the insertion. Also we can immediately return.

Fixes: 6c65fb318e8b ("iommu: iommu_get_group_resv_regions")

Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/iommu/iommu.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/iommu/iommu.c b/drivers/iommu/iommu.c
index 3de5c0bcb5cc..1620a6f49989 100644
--- a/drivers/iommu/iommu.c
+++ b/drivers/iommu/iommu.c
@@ -205,18 +205,21 @@ static int iommu_insert_resv_region(struct iommu_resv_region *new,
 			pos = pos->next;
 		} else if ((start >= a) && (end <= b)) {
 			if (new->type == type)
-				goto done;
+				return 0;
 			else
 				pos = pos->next;
 		} else {
 			if (new->type == type) {
 				phys_addr_t new_start = min(a, start);
 				phys_addr_t new_end = max(b, end);
+				int ret;
 
 				list_del(&entry->list);
 				entry->start = new_start;
 				entry->length = new_end - new_start + 1;
-				iommu_insert_resv_region(entry, regions);
+				ret = iommu_insert_resv_region(entry, regions);
+				kfree(entry);
+				return ret;
 			} else {
 				pos = pos->next;
 			}
@@ -229,7 +232,6 @@ static int iommu_insert_resv_region(struct iommu_resv_region *new,
 		return -ENOMEM;
 
 	list_add_tail(&region->list, pos);
-done:
 	return 0;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 044/105] gpio: omap: fix lack of irqstatus_raw0 for OMAP4

[Sasha Levin]

From: Russell King <rmk+kernel@armlinux.org.uk>

[ Upstream commit 64ea3e9094a1f13b96c33244a3fb3a0f45690bd2 ]

Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.

This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.

Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-omap.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 83c6843db50c..abe54659b1f4 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -1604,6 +1604,8 @@ static struct omap_gpio_reg_offs omap4_gpio_regs = {
 	.clr_dataout =		OMAP4_GPIO_CLEARDATAOUT,
 	.irqstatus =		OMAP4_GPIO_IRQSTATUS0,
 	.irqstatus2 =		OMAP4_GPIO_IRQSTATUS1,
+	.irqstatus_raw0 =	OMAP4_GPIO_IRQSTATUSRAW0,
+	.irqstatus_raw1 =	OMAP4_GPIO_IRQSTATUSRAW1,
 	.irqenable =		OMAP4_GPIO_IRQSTATUSSET0,
 	.irqenable2 =		OMAP4_GPIO_IRQSTATUSSET1,
 	.set_irqenable =	OMAP4_GPIO_IRQSTATUSSET0,
-- 
2.20.1

[PATCH AUTOSEL 4.14 045/105] gpio: omap: ensure irq is enabled before wakeup

[Sasha Levin]

From: Russell King <rmk+kernel@armlinux.org.uk>

[ Upstream commit c859e0d479b3b4f6132fc12637c51e01492f31f6 ]

Documentation states:

  NOTE: There must be a correlation between the wake-up enable and
  interrupt-enable registers. If a GPIO pin has a wake-up configured
  on it, it must also have the corresponding interrupt enabled (on
  one of the two interrupt lines).

Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt.  This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.

If we do any clearing, clear between the interrupt enable/disable and
trigger setting.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpio-omap.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index abe54659b1f4..47e537a91dd8 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -790,9 +790,9 @@ static void omap_gpio_irq_shutdown(struct irq_data *d)
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
 	bank->irq_usage &= ~(BIT(offset));
-	omap_set_gpio_irqenable(bank, offset, 0);
-	omap_clear_gpio_irqstatus(bank, offset);
 	omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
+	omap_clear_gpio_irqstatus(bank, offset);
+	omap_set_gpio_irqenable(bank, offset, 0);
 	if (!LINE_USED(bank->mod_usage, offset))
 		omap_clear_gpio_debounce(bank, offset);
 	omap_disable_gpio_module(bank, offset);
@@ -834,8 +834,8 @@ static void omap_gpio_mask_irq(struct irq_data *d)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
-	omap_set_gpio_irqenable(bank, offset, 0);
 	omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE);
+	omap_set_gpio_irqenable(bank, offset, 0);
 	raw_spin_unlock_irqrestore(&bank->lock, flags);
 }
 
@@ -847,9 +847,6 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
 	unsigned long flags;
 
 	raw_spin_lock_irqsave(&bank->lock, flags);
-	if (trigger)
-		omap_set_gpio_triggering(bank, offset, trigger);
-
 	omap_set_gpio_irqenable(bank, offset, 1);
 
 	/*
@@ -857,9 +854,13 @@ static void omap_gpio_unmask_irq(struct irq_data *d)
 	 * is cleared, thus after the handler has run. OMAP4 needs this done
 	 * after enabing the interrupt to clear the wakeup status.
 	 */
-	if (bank->level_mask & BIT(offset))
+	if (bank->regs->leveldetect0 && bank->regs->wkup_en &&
+	    trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
 		omap_clear_gpio_irqstatus(bank, offset);
 
+	if (trigger)
+		omap_set_gpio_triggering(bank, offset, trigger);
+
 	raw_spin_unlock_irqrestore(&bank->lock, flags);
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 046/105] regmap: fix bulk writes on paged registers

[Sasha Levin]

From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

[ Upstream commit db057679de3e9e6a03c1bcd5aee09b0d25fd9f5b ]

On buses like SlimBus and SoundWire which does not support
gather_writes yet in regmap, A bulk write on paged register
would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl()
gets reset to 0 once page register is written successfully and the
code below checks for 'ret' value to be -ENOTSUPP before linearising
the write buffer to send to bus->write().

Fix this by resetting the 'ret' value to -ENOTSUPP in cases where
gather_writes() is not supported or single register write is
not possible.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/base/regmap/regmap.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/base/regmap/regmap.c b/drivers/base/regmap/regmap.c
index 8fd08023c0f5..013d0a2b3ba0 100644
--- a/drivers/base/regmap/regmap.c
+++ b/drivers/base/regmap/regmap.c
@@ -1509,6 +1509,8 @@ int _regmap_raw_write(struct regmap *map, unsigned int reg,
 					     map->format.reg_bytes +
 					     map->format.pad_bytes,
 					     val, val_len);
+	else
+		ret = -ENOTSUPP;
 
 	/* If that didn't work fall back on linearising by hand. */
 	if (ret == -ENOTSUPP) {
-- 
2.20.1

[PATCH AUTOSEL 4.14 047/105] bpf: silence warning messages in core

[Sasha Levin]

From: Valdis Klētnieks <valdis.kletnieks@vt.edu>

[ Upstream commit aee450cbe482a8c2f6fa5b05b178ef8b8ff107ca ]

Compiling kernel/bpf/core.c with W=1 causes a flood of warnings:

kernel/bpf/core.c:1198:65: warning: initialized field overwritten [-Woverride-init]
 1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
      |                                                                 ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
 1087 |  INSN_3(ALU, ADD,  X),   \
      |  ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
 1202 |   BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
      |   ^~~~~~~~~~~~
kernel/bpf/core.c:1198:65: note: (near initialization for 'public_insntable[12]')
 1198 | #define BPF_INSN_3_TBL(x, y, z) [BPF_##x | BPF_##y | BPF_##z] = true
      |                                                                 ^~~~
kernel/bpf/core.c:1087:2: note: in expansion of macro 'BPF_INSN_3_TBL'
 1087 |  INSN_3(ALU, ADD,  X),   \
      |  ^~~~~~
kernel/bpf/core.c:1202:3: note: in expansion of macro 'BPF_INSN_MAP'
 1202 |   BPF_INSN_MAP(BPF_INSN_2_TBL, BPF_INSN_3_TBL),
      |   ^~~~~~~~~~~~

98 copies of the above.

The attached patch silences the warnings, because we *know* we're overwriting
the default initializer. That leaves bpf/core.c with only 6 other warnings,
which become more visible in comparison.

Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/bpf/Makefile | 1 +
 1 file changed, 1 insertion(+)

diff --git a/kernel/bpf/Makefile b/kernel/bpf/Makefile
index af3ab6164ff5..be282c135a66 100644
--- a/kernel/bpf/Makefile
+++ b/kernel/bpf/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 obj-y := core.o
+CFLAGS_core.o += $(call cc-disable-warning, override-init)
 
 obj-$(CONFIG_BPF_SYSCALL) += syscall.o verifier.o inode.o helpers.o tnum.o
 obj-$(CONFIG_BPF_SYSCALL) += hashtab.o arraymap.o percpu_freelist.o bpf_lru_list.o lpm_trie.o map_in_map.o
-- 
2.20.1

[PATCH AUTOSEL 4.14 048/105] rcu: Force inlining of rcu_read_lock()

[Sasha Levin]

From: Waiman Long <longman@redhat.com>

[ Upstream commit 6da9f775175e516fc7229ceaa9b54f8f56aa7924 ]

When debugging options are turned on, the rcu_read_lock() function
might not be inlined. This results in lockdep's print_lock() function
printing "rcu_read_lock+0x0/0x70" instead of rcu_read_lock()'s caller.
For example:

[   10.579995] =============================
[   10.584033] WARNING: suspicious RCU usage
[   10.588074] 4.18.0.memcg_v2+ #1 Not tainted
[   10.593162] -----------------------------
[   10.597203] include/linux/rcupdate.h:281 Illegal context switch in
RCU read-side critical section!
[   10.606220]
[   10.606220] other info that might help us debug this:
[   10.606220]
[   10.614280]
[   10.614280] rcu_scheduler_active = 2, debug_locks = 1
[   10.620853] 3 locks held by systemd/1:
[   10.624632]  #0: (____ptrval____) (&type->i_mutex_dir_key#5){.+.+}, at: lookup_slow+0x42/0x70
[   10.633232]  #1: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70
[   10.640954]  #2: (____ptrval____) (rcu_read_lock){....}, at: rcu_read_lock+0x0/0x70

These "rcu_read_lock+0x0/0x70" strings are not providing any useful
information.  This commit therefore forces inlining of the rcu_read_lock()
function so that rcu_read_lock()'s caller is instead shown.

Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/linux/rcupdate.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/rcupdate.h b/include/linux/rcupdate.h
index f960c85cd9ec..8d570190e9b4 100644
--- a/include/linux/rcupdate.h
+++ b/include/linux/rcupdate.h
@@ -622,7 +622,7 @@ static inline void rcu_preempt_sleep_check(void) { }
  * read-side critical sections may be preempted and they may also block, but
  * only when acquiring spinlocks that are subject to priority inheritance.
  */
-static inline void rcu_read_lock(void)
+static __always_inline void rcu_read_lock(void)
 {
 	__rcu_read_lock();
 	__acquire(RCU);
-- 
2.20.1

[PATCH AUTOSEL 4.14 049/105] x86/cpufeatures: Add FDP_EXCPTN_ONLY and ZERO_FCS_FDS

[Sasha Levin]

From: Aaron Lewis <aaronlewis@google.com>

[ Upstream commit cbb99c0f588737ec98c333558922ce47e9a95827 ]

Add the CPUID enumeration for Intel's de-feature bits to accommodate
passing these de-features through to kvm guests.

These de-features are (from SDM vol 1, section 8.1.8):
 - X86_FEATURE_FDP_EXCPTN_ONLY: If CPUID.(EAX=07H,ECX=0H):EBX[bit 6] = 1, the
   data pointer (FDP) is updated only for the x87 non-control instructions that
   incur unmasked x87 exceptions.
 - X86_FEATURE_ZERO_FCS_FDS: If CPUID.(EAX=07H,ECX=0H):EBX[bit 13] = 1, the
   processor deprecates FCS and FDS; it saves each as 0000H.

Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: marcorr@google.com
Cc: Peter Feiner <pfeiner@google.com>
Cc: pshier@google.com
Cc: Robert Hoo <robert.hu@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Lendacky <Thomas.Lendacky@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190605220252.103406-1-aaronlewis@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/include/asm/cpufeatures.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/x86/include/asm/cpufeatures.h b/arch/x86/include/asm/cpufeatures.h
index 48ef9ed8226d..4cb8315c521f 100644
--- a/arch/x86/include/asm/cpufeatures.h
+++ b/arch/x86/include/asm/cpufeatures.h
@@ -239,12 +239,14 @@
 #define X86_FEATURE_BMI1		( 9*32+ 3) /* 1st group bit manipulation extensions */
 #define X86_FEATURE_HLE			( 9*32+ 4) /* Hardware Lock Elision */
 #define X86_FEATURE_AVX2		( 9*32+ 5) /* AVX2 instructions */
+#define X86_FEATURE_FDP_EXCPTN_ONLY	( 9*32+ 6) /* "" FPU data pointer updated only on x87 exceptions */
 #define X86_FEATURE_SMEP		( 9*32+ 7) /* Supervisor Mode Execution Protection */
 #define X86_FEATURE_BMI2		( 9*32+ 8) /* 2nd group bit manipulation extensions */
 #define X86_FEATURE_ERMS		( 9*32+ 9) /* Enhanced REP MOVSB/STOSB instructions */
 #define X86_FEATURE_INVPCID		( 9*32+10) /* Invalidate Processor Context ID */
 #define X86_FEATURE_RTM			( 9*32+11) /* Restricted Transactional Memory */
 #define X86_FEATURE_CQM			( 9*32+12) /* Cache QoS Monitoring */
+#define X86_FEATURE_ZERO_FCS_FDS	( 9*32+13) /* "" Zero out FPU CS and FPU DS */
 #define X86_FEATURE_MPX			( 9*32+14) /* Memory Protection Extension */
 #define X86_FEATURE_RDT_A		( 9*32+15) /* Resource Director Technology Allocation */
 #define X86_FEATURE_AVX512F		( 9*32+16) /* AVX-512 Foundation */
-- 
2.20.1

[PATCH AUTOSEL 4.14 050/105] blkcg, writeback: dead memcgs shouldn't contribute to writeback ownership arbitration

[Sasha Levin]

From: Tejun Heo <tj@kernel.org>

[ Upstream commit 6631142229005e1b1c311a09efe9fb3cfdac8559 ]

wbc_account_io() collects information on cgroup ownership of writeback
pages to determine which cgroup should own the inode.  Pages can stay
associated with dead memcgs but we want to avoid attributing IOs to
dead blkcgs as much as possible as the association is likely to be
stale.  However, currently, pages associated with dead memcgs
contribute to the accounting delaying and/or confusing the
arbitration.

Fix it by ignoring pages associated with dead memcgs.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/fs-writeback.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/fs/fs-writeback.c b/fs/fs-writeback.c
index 4d561ee08d05..9e8fde348d61 100644
--- a/fs/fs-writeback.c
+++ b/fs/fs-writeback.c
@@ -721,6 +721,7 @@ void wbc_detach_inode(struct writeback_control *wbc)
 void wbc_account_io(struct writeback_control *wbc, struct page *page,
 		    size_t bytes)
 {
+	struct cgroup_subsys_state *css;
 	int id;
 
 	/*
@@ -732,7 +733,12 @@ void wbc_account_io(struct writeback_control *wbc, struct page *page,
 	if (!wbc->wb)
 		return;
 
-	id = mem_cgroup_css_from_page(page)->id;
+	css = mem_cgroup_css_from_page(page);
+	/* dead cgroups shouldn't contribute to inode ownership arbitration */
+	if (!(css->flags & CSS_ONLINE))
+		return;
+
+	id = css->id;
 
 	if (id == wbc->wb_id) {
 		wbc->wb_bytes += bytes;
-- 
2.20.1

[PATCH AUTOSEL 4.14 051/105] xfrm: fix sa selector validation

[Sasha Levin]

From: Nicolas Dichtel <nicolas.dichtel@6wind.com>

[ Upstream commit b8d6d0079757cbd1b69724cfd1c08e2171c68cee ]

After commit b38ff4075a80, the following command does not work anymore:
$ ip xfrm state add src 10.125.0.2 dst 10.125.0.1 proto esp spi 34 reqid 1 \
  mode tunnel enc 'cbc(aes)' 0xb0abdba8b782ad9d364ec81e3a7d82a1 auth-trunc \
  'hmac(sha1)' 0xe26609ebd00acb6a4d51fca13e49ea78a72c73e6 96 flag align4

In fact, the selector is not mandatory, allow the user to provide an empty
selector.

Fixes: b38ff4075a80 ("xfrm: Fix xfrm sel prefix length validation")
CC: Anirudh Gupta <anirudh.gupta@sophos.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/xfrm/xfrm_user.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/net/xfrm/xfrm_user.c b/net/xfrm/xfrm_user.c
index b25b68ae7c74..150c58dc8a7b 100644
--- a/net/xfrm/xfrm_user.c
+++ b/net/xfrm/xfrm_user.c
@@ -166,6 +166,9 @@ static int verify_newsa_info(struct xfrm_usersa_info *p,
 	}
 
 	switch (p->sel.family) {
+	case AF_UNSPEC:
+		break;
+
 	case AF_INET:
 		if (p->sel.prefixlen_d > 32 || p->sel.prefixlen_s > 32)
 			goto out;
-- 
2.20.1

[PATCH AUTOSEL 4.14 052/105] sched/core: Add __sched tag for io_schedule()

[Sasha Levin]

From: Gao Xiang <gaoxiang25@huawei.com>

[ Upstream commit e3b929b0a184edb35531153c5afcaebb09014f9d ]

Non-inline io_schedule() was introduced in:

  commit 10ab56434f2f ("sched/core: Separate out io_schedule_prepare() and io_schedule_finish()")

Keep in line with io_schedule_timeout(), otherwise "/proc/<pid>/wchan" will
report io_schedule() rather than its callers when waiting for IO.

Reported-by: Jilong Kou <koujilong@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miao Xie <miaoxie@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 10ab56434f2f ("sched/core: Separate out io_schedule_prepare() and io_schedule_finish()")
Link: https://lkml.kernel.org/r/20190603091338.2695-1-gaoxiang25@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/sched/core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/sched/core.c b/kernel/sched/core.c
index b3ff73d6a4c2..ff128e281d1c 100644
--- a/kernel/sched/core.c
+++ b/kernel/sched/core.c
@@ -5026,7 +5026,7 @@ long __sched io_schedule_timeout(long timeout)
 }
 EXPORT_SYMBOL(io_schedule_timeout);
 
-void io_schedule(void)
+void __sched io_schedule(void)
 {
 	int token;
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 053/105] sched/fair: Fix "runnable_avg_yN_inv" not used warnings

[Sasha Levin]

From: Qian Cai <cai@lca.pw>

[ Upstream commit 509466b7d480bc5d22e90b9fbe6122ae0e2fbe39 ]

runnable_avg_yN_inv[] is only used in kernel/sched/pelt.c but was
included in several other places because they need other macros all
came from kernel/sched/sched-pelt.h which was generated by
Documentation/scheduler/sched-pelt. As the result, it causes compilation
a lot of warnings,

  kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
  kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
  kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
  ...

Silence it by appending the __maybe_unused attribute for it, so all
generated variables and macros can still be kept in the same file.

Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1559596304-31581-1-git-send-email-cai@lca.pw
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 Documentation/scheduler/sched-pelt.c | 3 ++-
 kernel/sched/sched-pelt.h            | 2 +-
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/scheduler/sched-pelt.c b/Documentation/scheduler/sched-pelt.c
index e4219139386a..7238b355919c 100644
--- a/Documentation/scheduler/sched-pelt.c
+++ b/Documentation/scheduler/sched-pelt.c
@@ -20,7 +20,8 @@ void calc_runnable_avg_yN_inv(void)
 	int i;
 	unsigned int x;
 
-	printf("static const u32 runnable_avg_yN_inv[] = {");
+	/* To silence -Wunused-but-set-variable warnings. */
+	printf("static const u32 runnable_avg_yN_inv[] __maybe_unused = {");
 	for (i = 0; i < HALFLIFE; i++) {
 		x = ((1UL<<32)-1)*pow(y, i);
 
diff --git a/kernel/sched/sched-pelt.h b/kernel/sched/sched-pelt.h
index a26473674fb7..c529706bed11 100644
--- a/kernel/sched/sched-pelt.h
+++ b/kernel/sched/sched-pelt.h
@@ -1,7 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0 */
 /* Generated by Documentation/scheduler/sched-pelt; do not modify. */
 
-static const u32 runnable_avg_yN_inv[] = {
+static const u32 runnable_avg_yN_inv[] __maybe_unused = {
 	0xffffffff, 0xfa83b2da, 0xf5257d14, 0xefe4b99a, 0xeac0c6e6, 0xe5b906e6,
 	0xe0ccdeeb, 0xdbfbb796, 0xd744fcc9, 0xd2a81d91, 0xce248c14, 0xc9b9bd85,
 	0xc5672a10, 0xc12c4cc9, 0xbd08a39e, 0xb8fbaf46, 0xb504f333, 0xb123f581,
-- 
2.20.1

[PATCH AUTOSEL 4.14 054/105] x86/atomic: Fix smp_mb__{before,after}_atomic()

[Sasha Levin]

From: Peter Zijlstra <peterz@infradead.org>

[ Upstream commit 69d927bba39517d0980462efc051875b7f4db185 ]

Recent probing at the Linux Kernel Memory Model uncovered a
'surprise'. Strongly ordered architectures where the atomic RmW
primitive implies full memory ordering and
smp_mb__{before,after}_atomic() are a simple barrier() (such as x86)
fail for:

	*x = 1;
	atomic_inc(u);
	smp_mb__after_atomic();
	r0 = *y;

Because, while the atomic_inc() implies memory order, it
(surprisingly) does not provide a compiler barrier. This then allows
the compiler to re-order like so:

	atomic_inc(u);
	*x = 1;
	smp_mb__after_atomic();
	r0 = *y;

Which the CPU is then allowed to re-order (under TSO rules) like:

	atomic_inc(u);
	r0 = *y;
	*x = 1;

And this very much was not intended. Therefore strengthen the atomic
RmW ops to include a compiler barrier.

NOTE: atomic_{or,and,xor} and the bitops already had the compiler
barrier.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 Documentation/atomic_t.txt         | 3 +++
 arch/x86/include/asm/atomic.h      | 8 ++++----
 arch/x86/include/asm/atomic64_64.h | 8 ++++----
 arch/x86/include/asm/barrier.h     | 4 ++--
 4 files changed, 13 insertions(+), 10 deletions(-)

diff --git a/Documentation/atomic_t.txt b/Documentation/atomic_t.txt
index 913396ac5824..ed0d814df7e0 100644
--- a/Documentation/atomic_t.txt
+++ b/Documentation/atomic_t.txt
@@ -177,6 +177,9 @@ These helper barriers exist because architectures have varying implicit
 ordering on their SMP atomic primitives. For example our TSO architectures
 provide full ordered atomics and these barriers are no-ops.
 
+NOTE: when the atomic RmW ops are fully ordered, they should also imply a
+compiler barrier.
+
 Thus:
 
   atomic_fetch_add();
diff --git a/arch/x86/include/asm/atomic.h b/arch/x86/include/asm/atomic.h
index 72759f131cc5..d09dd91dd0b6 100644
--- a/arch/x86/include/asm/atomic.h
+++ b/arch/x86/include/asm/atomic.h
@@ -50,7 +50,7 @@ static __always_inline void atomic_add(int i, atomic_t *v)
 {
 	asm volatile(LOCK_PREFIX "addl %1,%0"
 		     : "+m" (v->counter)
-		     : "ir" (i));
+		     : "ir" (i) : "memory");
 }
 
 /**
@@ -64,7 +64,7 @@ static __always_inline void atomic_sub(int i, atomic_t *v)
 {
 	asm volatile(LOCK_PREFIX "subl %1,%0"
 		     : "+m" (v->counter)
-		     : "ir" (i));
+		     : "ir" (i) : "memory");
 }
 
 /**
@@ -90,7 +90,7 @@ static __always_inline bool atomic_sub_and_test(int i, atomic_t *v)
 static __always_inline void atomic_inc(atomic_t *v)
 {
 	asm volatile(LOCK_PREFIX "incl %0"
-		     : "+m" (v->counter));
+		     : "+m" (v->counter) :: "memory");
 }
 
 /**
@@ -102,7 +102,7 @@ static __always_inline void atomic_inc(atomic_t *v)
 static __always_inline void atomic_dec(atomic_t *v)
 {
 	asm volatile(LOCK_PREFIX "decl %0"
-		     : "+m" (v->counter));
+		     : "+m" (v->counter) :: "memory");
 }
 
 /**
diff --git a/arch/x86/include/asm/atomic64_64.h b/arch/x86/include/asm/atomic64_64.h
index 738495caf05f..e6fad6bbb2ee 100644
--- a/arch/x86/include/asm/atomic64_64.h
+++ b/arch/x86/include/asm/atomic64_64.h
@@ -45,7 +45,7 @@ static __always_inline void atomic64_add(long i, atomic64_t *v)
 {
 	asm volatile(LOCK_PREFIX "addq %1,%0"
 		     : "=m" (v->counter)
-		     : "er" (i), "m" (v->counter));
+		     : "er" (i), "m" (v->counter) : "memory");
 }
 
 /**
@@ -59,7 +59,7 @@ static inline void atomic64_sub(long i, atomic64_t *v)
 {
 	asm volatile(LOCK_PREFIX "subq %1,%0"
 		     : "=m" (v->counter)
-		     : "er" (i), "m" (v->counter));
+		     : "er" (i), "m" (v->counter) : "memory");
 }
 
 /**
@@ -86,7 +86,7 @@ static __always_inline void atomic64_inc(atomic64_t *v)
 {
 	asm volatile(LOCK_PREFIX "incq %0"
 		     : "=m" (v->counter)
-		     : "m" (v->counter));
+		     : "m" (v->counter) : "memory");
 }
 
 /**
@@ -99,7 +99,7 @@ static __always_inline void atomic64_dec(atomic64_t *v)
 {
 	asm volatile(LOCK_PREFIX "decq %0"
 		     : "=m" (v->counter)
-		     : "m" (v->counter));
+		     : "m" (v->counter) : "memory");
 }
 
 /**
diff --git a/arch/x86/include/asm/barrier.h b/arch/x86/include/asm/barrier.h
index a04f0c242a28..bc88797cfa61 100644
--- a/arch/x86/include/asm/barrier.h
+++ b/arch/x86/include/asm/barrier.h
@@ -106,8 +106,8 @@ do {									\
 #endif
 
 /* Atomic operations are already serializing on x86 */
-#define __smp_mb__before_atomic()	barrier()
-#define __smp_mb__after_atomic()	barrier()
+#define __smp_mb__before_atomic()	do { } while (0)
+#define __smp_mb__after_atomic()	do { } while (0)
 
 #include <asm-generic/barrier.h>
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 055/105] perf evsel: Make perf_evsel__name() accept a NULL argument

[Sasha Levin]

From: Arnaldo Carvalho de Melo <acme@redhat.com>

[ Upstream commit fdbdd7e8580eac9bdafa532746c865644d125e34 ]

In which case it simply returns "unknown", like when it can't figure out
the evsel->name value.

This makes this code more robust and fixes a problem in 'perf trace'
where a NULL evsel was being passed to a routine that only used the
evsel for printing its name when a invalid syscall id was passed.

Reported-by: Leo Yan <leo.yan@linaro.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-f30ztaasku3z935cn3ak3h53@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/perf/util/evsel.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/tools/perf/util/evsel.c b/tools/perf/util/evsel.c
index 0cf6f537f980..3ab81e8e079e 100644
--- a/tools/perf/util/evsel.c
+++ b/tools/perf/util/evsel.c
@@ -587,6 +587,9 @@ const char *perf_evsel__name(struct perf_evsel *evsel)
 {
 	char bf[128];
 
+	if (!evsel)
+		goto out_unknown;
+
 	if (evsel->name)
 		return evsel->name;
 
@@ -623,7 +626,10 @@ const char *perf_evsel__name(struct perf_evsel *evsel)
 
 	evsel->name = strdup(bf);
 
-	return evsel->name ?: "unknown";
+	if (evsel->name)
+		return evsel->name;
+out_unknown:
+	return "unknown";
 }
 
 const char *perf_evsel__group_name(struct perf_evsel *evsel)
-- 
2.20.1

[PATCH AUTOSEL 4.14 056/105] vhost_net: disable zerocopy by default

[Sasha Levin]

From: Jason Wang <jasowang@redhat.com>

[ Upstream commit 098eadce3c622c07b328d0a43dda379b38cf7c5e ]

Vhost_net was known to suffer from HOL[1] issues which is not easy to
fix. Several downstream disable the feature by default. What's more,
the datapath was split and datacopy path got the support of batching
and XDP support recently which makes it faster than zerocopy part for
small packets transmission.

It looks to me that disable zerocopy by default is more
appropriate. It cold be enabled by default again in the future if we
fix the above issues.

[1] https://patchwork.kernel.org/patch/3787671/

Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/vhost/net.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/vhost/net.c b/drivers/vhost/net.c
index b40e8ded49c6..4d11152e60c1 100644
--- a/drivers/vhost/net.c
+++ b/drivers/vhost/net.c
@@ -35,7 +35,7 @@
 
 #include "vhost.h"
 
-static int experimental_zcopytx = 1;
+static int experimental_zcopytx = 0;
 module_param(experimental_zcopytx, int, 0444);
 MODULE_PARM_DESC(experimental_zcopytx, "Enable Zero Copy TX;"
 		                       " 1 -Enable; 0 - Disable");
-- 
2.20.1

[PATCH AUTOSEL 4.14 057/105] ipoib: correcly show a VF hardware address

[Sasha Levin]

From: Denis Kirjanov <kda@linux-powerpc.org>

[ Upstream commit 64d701c608fea362881e823b666327f5d28d7ffd ]

in the case of IPoIB with SRIOV enabled hardware
ip link show command incorrecly prints
0 instead of a VF hardware address.

Before:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
    link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state disable,
trust off, query_rss off
...
After:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
    link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    vf 0     link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff, spoof
checking off, link-state disable, trust off, query_rss off

v1->v2: just copy an address without modifing ifla_vf_mac
v2->v3: update the changelog

Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/infiniband/ulp/ipoib/ipoib_main.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/infiniband/ulp/ipoib/ipoib_main.c b/drivers/infiniband/ulp/ipoib/ipoib_main.c
index e6ff16b27acd..1a93d3d58c8a 100644
--- a/drivers/infiniband/ulp/ipoib/ipoib_main.c
+++ b/drivers/infiniband/ulp/ipoib/ipoib_main.c
@@ -1833,6 +1833,7 @@ static int ipoib_get_vf_config(struct net_device *dev, int vf,
 		return err;
 
 	ivf->vf = vf;
+	memcpy(ivf->mac, dev->dev_addr, dev->addr_len);
 
 	return 0;
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 058/105] EDAC/sysfs: Fix memory leak when creating a csrow object

[Sasha Levin]

From: Pan Bian <bianpan2016@163.com>

[ Upstream commit 585fb3d93d32dbe89e718b85009f9c322cc554cd ]

In edac_create_csrow_object(), the reference to the object is not
released when adding the device to the device hierarchy fails
(device_add()). This may result in a memory leak.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/1555554438-103953-1-git-send-email-bianpan2016@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/edac/edac_mc_sysfs.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/edac/edac_mc_sysfs.c b/drivers/edac/edac_mc_sysfs.c
index 79c13301bf41..148c4649b155 100644
--- a/drivers/edac/edac_mc_sysfs.c
+++ b/drivers/edac/edac_mc_sysfs.c
@@ -426,6 +426,8 @@ static inline int nr_pages_per_csrow(struct csrow_info *csrow)
 static int edac_create_csrow_object(struct mem_ctl_info *mci,
 				    struct csrow_info *csrow, int index)
 {
+	int err;
+
 	csrow->dev.type = &csrow_attr_type;
 	csrow->dev.bus = mci->bus;
 	csrow->dev.groups = csrow_dev_groups;
@@ -438,7 +440,11 @@ static int edac_create_csrow_object(struct mem_ctl_info *mci,
 	edac_dbg(0, "creating (virtual) csrow node %s\n",
 		 dev_name(&csrow->dev));
 
-	return device_add(&csrow->dev);
+	err = device_add(&csrow->dev);
+	if (err)
+		put_device(&csrow->dev);
+
+	return err;
 }
 
 /* Create a CSROW object under specifed edac_mc_device */
-- 
2.20.1

[PATCH AUTOSEL 4.14 059/105] ipsec: select crypto ciphers for xfrm_algo

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 597179b0ba550bd83fab1a9d57c42a9343c58514 ]

kernelci.org reports failed builds on arc because of what looks
like an old missed 'select' statement:

net/xfrm/xfrm_algo.o: In function `xfrm_probe_algs':
xfrm_algo.c:(.text+0x1e8): undefined reference to `crypto_has_ahash'

I don't see this in randconfig builds on other architectures, but
it's fairly clear we want to select the hash code for it, like we
do for all its other users. As Herbert points out, CRYPTO_BLKCIPHER
is also required even though it has not popped up in build tests.

Fixes: 17bc19702221 ("ipsec: Use skcipher and ahash when probing algorithms")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/xfrm/Kconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/net/xfrm/Kconfig b/net/xfrm/Kconfig
index 286ed25c1a69..2e747ae7dc89 100644
--- a/net/xfrm/Kconfig
+++ b/net/xfrm/Kconfig
@@ -14,6 +14,8 @@ config XFRM_ALGO
 	tristate
 	select XFRM
 	select CRYPTO
+	select CRYPTO_HASH
+	select CRYPTO_BLKCIPHER
 
 config XFRM_USER
 	tristate "Transformation user configuration interface"
-- 
2.20.1

[PATCH AUTOSEL 4.14 060/105] ipvs: defer hook registration to avoid leaks

[Sasha Levin]

From: Julian Anastasov <ja@ssi.bg>

[ Upstream commit cf47a0b882a4e5f6b34c7949d7b293e9287f1972 ]

syzkaller reports for memory leak when registering hooks [1]

As we moved the nf_unregister_net_hooks() call into
__ip_vs_dev_cleanup(), defer the nf_register_net_hooks()
call, so that hooks are allocated and freed from same
pernet_operations (ipvs_core_dev_ops).

[1]
BUG: memory leak
unreferenced object 0xffff88810acd8a80 (size 96):
 comm "syz-executor073", pid 7254, jiffies 4294950560 (age 22.250s)
 hex dump (first 32 bytes):
   02 00 00 00 00 00 00 00 50 8b bb 82 ff ff ff ff  ........P.......
   00 00 00 00 00 00 00 00 00 77 bb 82 ff ff ff ff  .........w......
 backtrace:
   [<0000000013db61f1>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
   [<0000000013db61f1>] slab_post_alloc_hook mm/slab.h:439 [inline]
   [<0000000013db61f1>] slab_alloc_node mm/slab.c:3269 [inline]
   [<0000000013db61f1>] kmem_cache_alloc_node_trace+0x15b/0x2a0 mm/slab.c:3597
   [<000000001a27307d>] __do_kmalloc_node mm/slab.c:3619 [inline]
   [<000000001a27307d>] __kmalloc_node+0x38/0x50 mm/slab.c:3627
   [<0000000025054add>] kmalloc_node include/linux/slab.h:590 [inline]
   [<0000000025054add>] kvmalloc_node+0x4a/0xd0 mm/util.c:431
   [<0000000050d1bc00>] kvmalloc include/linux/mm.h:637 [inline]
   [<0000000050d1bc00>] kvzalloc include/linux/mm.h:645 [inline]
   [<0000000050d1bc00>] allocate_hook_entries_size+0x3b/0x60 net/netfilter/core.c:61
   [<00000000e8abe142>] nf_hook_entries_grow+0xae/0x270 net/netfilter/core.c:128
   [<000000004b94797c>] __nf_register_net_hook+0x9a/0x170 net/netfilter/core.c:337
   [<00000000d1545cbc>] nf_register_net_hook+0x34/0xc0 net/netfilter/core.c:464
   [<00000000876c9b55>] nf_register_net_hooks+0x53/0xc0 net/netfilter/core.c:480
   [<000000002ea868e0>] __ip_vs_init+0xe8/0x170 net/netfilter/ipvs/ip_vs_core.c:2280
   [<000000002eb2d451>] ops_init+0x4c/0x140 net/core/net_namespace.c:130
   [<000000000284ec48>] setup_net+0xde/0x230 net/core/net_namespace.c:316
   [<00000000a70600fa>] copy_net_ns+0xf0/0x1e0 net/core/net_namespace.c:439
   [<00000000ff26c15e>] create_new_namespaces+0x141/0x2a0 kernel/nsproxy.c:107
   [<00000000b103dc79>] copy_namespaces+0xa1/0xe0 kernel/nsproxy.c:165
   [<000000007cc008a2>] copy_process.part.0+0x11fd/0x2150 kernel/fork.c:2035
   [<00000000c344af7c>] copy_process kernel/fork.c:1800 [inline]
   [<00000000c344af7c>] _do_fork+0x121/0x4f0 kernel/fork.c:2369

Reported-by: syzbot+722da59ccb264bc19910@syzkaller.appspotmail.com
Fixes: 719c7d563c17 ("ipvs: Fix use-after-free in ip_vs_in")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/netfilter/ipvs/ip_vs_core.c | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/net/netfilter/ipvs/ip_vs_core.c b/net/netfilter/ipvs/ip_vs_core.c
index ee97ce176b9a..2156571455db 100644
--- a/net/netfilter/ipvs/ip_vs_core.c
+++ b/net/netfilter/ipvs/ip_vs_core.c
@@ -2206,7 +2206,6 @@ static const struct nf_hook_ops ip_vs_ops[] = {
 static int __net_init __ip_vs_init(struct net *net)
 {
 	struct netns_ipvs *ipvs;
-	int ret;
 
 	ipvs = net_generic(net, ip_vs_net_id);
 	if (ipvs == NULL)
@@ -2238,17 +2237,11 @@ static int __net_init __ip_vs_init(struct net *net)
 	if (ip_vs_sync_net_init(ipvs) < 0)
 		goto sync_fail;
 
-	ret = nf_register_net_hooks(net, ip_vs_ops, ARRAY_SIZE(ip_vs_ops));
-	if (ret < 0)
-		goto hook_fail;
-
 	return 0;
 /*
  * Error handling
  */
 
-hook_fail:
-	ip_vs_sync_net_cleanup(ipvs);
 sync_fail:
 	ip_vs_conn_net_cleanup(ipvs);
 conn_fail:
@@ -2278,6 +2271,19 @@ static void __net_exit __ip_vs_cleanup(struct net *net)
 	net->ipvs = NULL;
 }
 
+static int __net_init __ip_vs_dev_init(struct net *net)
+{
+	int ret;
+
+	ret = nf_register_net_hooks(net, ip_vs_ops, ARRAY_SIZE(ip_vs_ops));
+	if (ret < 0)
+		goto hook_fail;
+	return 0;
+
+hook_fail:
+	return ret;
+}
+
 static void __net_exit __ip_vs_dev_cleanup(struct net *net)
 {
 	struct netns_ipvs *ipvs = net_ipvs(net);
@@ -2297,6 +2303,7 @@ static struct pernet_operations ipvs_core_ops = {
 };
 
 static struct pernet_operations ipvs_core_dev_ops = {
+	.init = __ip_vs_dev_init,
 	.exit = __ip_vs_dev_cleanup,
 };
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 061/105] media: s5p-mfc: Make additional clocks optional

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit e08efef8fe7db87206314c19b341612c719f891a ]

Since the beginning the second clock ('special', 'sclk') was optional and
it is not available on some variants of Exynos SoCs (i.e. Exynos5420 with
v7 of MFC hardware).

However commit 1bce6fb3edf1 ("[media] s5p-mfc: Rework clock handling")
made handling of all specified clocks mandatory. This patch restores
original behavior of the driver and fixes its operation on
Exynos5420 SoCs.

Fixes: 1bce6fb3edf1 ("[media] s5p-mfc: Rework clock handling")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/s5p-mfc/s5p_mfc_pm.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/media/platform/s5p-mfc/s5p_mfc_pm.c b/drivers/media/platform/s5p-mfc/s5p_mfc_pm.c
index eb85cedc5ef3..5e080f32b0e8 100644
--- a/drivers/media/platform/s5p-mfc/s5p_mfc_pm.c
+++ b/drivers/media/platform/s5p-mfc/s5p_mfc_pm.c
@@ -38,6 +38,11 @@ int s5p_mfc_init_pm(struct s5p_mfc_dev *dev)
 	for (i = 0; i < pm->num_clocks; i++) {
 		pm->clocks[i] = devm_clk_get(pm->device, pm->clk_names[i]);
 		if (IS_ERR(pm->clocks[i])) {
+			/* additional clocks are optional */
+			if (i && PTR_ERR(pm->clocks[i]) == -ENOENT) {
+				pm->clocks[i] = NULL;
+				continue;
+			}
 			mfc_err("Failed to get clock: %s\n",
 				pm->clk_names[i]);
 			return PTR_ERR(pm->clocks[i]);
-- 
2.20.1

[PATCH AUTOSEL 4.14 062/105] media: i2c: fix warning same module names

[Sasha Levin]

From: Anders Roxell <anders.roxell@linaro.org>

[ Upstream commit b2ce5617dad254230551feda3599f2cc68e53ad8 ]

When building with CONFIG_VIDEO_ADV7511 and CONFIG_DRM_I2C_ADV7511
enabled as loadable modules, we see the following warning:

  drivers/gpu/drm/bridge/adv7511/adv7511.ko
  drivers/media/i2c/adv7511.ko

Rework so that the file is named adv7511-v4l2.c.

Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/Makefile                      | 2 +-
 drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} | 5 +++++
 2 files changed, 6 insertions(+), 1 deletion(-)
 rename drivers/media/i2c/{adv7511.c => adv7511-v4l2.c} (99%)

diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index f104650d6000..0f5c5a3cdca3 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -33,7 +33,7 @@ obj-$(CONFIG_VIDEO_ADV748X) += adv748x/
 obj-$(CONFIG_VIDEO_ADV7604) += adv7604.o
 obj-$(CONFIG_VIDEO_ADV7842) += adv7842.o
 obj-$(CONFIG_VIDEO_AD9389B) += ad9389b.o
-obj-$(CONFIG_VIDEO_ADV7511) += adv7511.o
+obj-$(CONFIG_VIDEO_ADV7511) += adv7511-v4l2.o
 obj-$(CONFIG_VIDEO_VPX3220) += vpx3220.o
 obj-$(CONFIG_VIDEO_VS6624)  += vs6624.o
 obj-$(CONFIG_VIDEO_BT819) += bt819.o
diff --git a/drivers/media/i2c/adv7511.c b/drivers/media/i2c/adv7511-v4l2.c
similarity index 99%
rename from drivers/media/i2c/adv7511.c
rename to drivers/media/i2c/adv7511-v4l2.c
index 80c20404334a..ef1144668809 100644
--- a/drivers/media/i2c/adv7511.c
+++ b/drivers/media/i2c/adv7511-v4l2.c
@@ -17,6 +17,11 @@
  * SOFTWARE.
  */
 
+/*
+ * This file is named adv7511-v4l2.c so it doesn't conflict with the Analog
+ * Device ADV7511 (config fragment CONFIG_DRM_I2C_ADV7511).
+ */
+
 
 #include <linux/kernel.h>
 #include <linux/module.h>
-- 
2.20.1

[PATCH AUTOSEL 4.14 063/105] ntp: Limit TAI-UTC offset

[Sasha Levin]

From: Miroslav Lichvar <mlichvar@redhat.com>

[ Upstream commit d897a4ab11dc8a9fda50d2eccc081a96a6385998 ]

Don't allow the TAI-UTC offset of the system clock to be set by adjtimex()
to a value larger than 100000 seconds.

This prevents an overflow in the conversion to int, prevents the CLOCK_TAI
clock from getting too far ahead of the CLOCK_REALTIME clock, and it is
still large enough to allow leap seconds to be inserted at the maximum rate
currently supported by the kernel (once per day) for the next ~270 years,
however unlikely it is that someone can survive a catastrophic event which
slowed down the rotation of the Earth so much.

Reported-by: Weikang shi <swkhack@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190618154713.20929-1-mlichvar@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/time/ntp.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/kernel/time/ntp.c b/kernel/time/ntp.c
index 4bb9b66338be..9288532f73c8 100644
--- a/kernel/time/ntp.c
+++ b/kernel/time/ntp.c
@@ -43,6 +43,7 @@ static u64			tick_length_base;
 #define MAX_TICKADJ		500LL		/* usecs */
 #define MAX_TICKADJ_SCALED \
 	(((MAX_TICKADJ * NSEC_PER_USEC) << NTP_SCALE_SHIFT) / NTP_INTERVAL_FREQ)
+#define MAX_TAI_OFFSET		100000
 
 /*
  * phase-lock loop variables
@@ -640,7 +641,8 @@ static inline void process_adjtimex_modes(struct timex *txc,
 		time_constant = max(time_constant, 0l);
 	}
 
-	if (txc->modes & ADJ_TAI && txc->constant >= 0)
+	if (txc->modes & ADJ_TAI &&
+			txc->constant >= 0 && txc->constant <= MAX_TAI_OFFSET)
 		*time_tai = txc->constant;
 
 	if (txc->modes & ADJ_OFFSET)
-- 
2.20.1

[PATCH AUTOSEL 4.14 064/105] timer_list: Guard procfs specific code

[Sasha Levin]

From: Nathan Huckleberry <nhuck@google.com>

[ Upstream commit a9314773a91a1d3b36270085246a6715a326ff00 ]

With CONFIG_PROC_FS=n the following warning is emitted:

kernel/time/timer_list.c:361:36: warning: unused variable
'timer_list_sops' [-Wunused-const-variable]
   static const struct seq_operations timer_list_sops = {

Add #ifdef guard around procfs specific code.

Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: john.stultz@linaro.org
Cc: sboyd@kernel.org
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/534
Link: https://lkml.kernel.org/r/20190614181604.112297-1-nhuck@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/time/timer_list.c | 36 +++++++++++++++++++-----------------
 1 file changed, 19 insertions(+), 17 deletions(-)

diff --git a/kernel/time/timer_list.c b/kernel/time/timer_list.c
index 0ed768b56c60..7e9f149d34ea 100644
--- a/kernel/time/timer_list.c
+++ b/kernel/time/timer_list.c
@@ -289,23 +289,6 @@ static inline void timer_list_header(struct seq_file *m, u64 now)
 	SEQ_printf(m, "\n");
 }
 
-static int timer_list_show(struct seq_file *m, void *v)
-{
-	struct timer_list_iter *iter = v;
-
-	if (iter->cpu == -1 && !iter->second_pass)
-		timer_list_header(m, iter->now);
-	else if (!iter->second_pass)
-		print_cpu(m, iter->cpu, iter->now);
-#ifdef CONFIG_GENERIC_CLOCKEVENTS
-	else if (iter->cpu == -1 && iter->second_pass)
-		timer_list_show_tickdevices_header(m);
-	else
-		print_tickdevice(m, tick_get_device(iter->cpu), iter->cpu);
-#endif
-	return 0;
-}
-
 void sysrq_timer_list_show(void)
 {
 	u64 now = ktime_to_ns(ktime_get());
@@ -324,6 +307,24 @@ void sysrq_timer_list_show(void)
 	return;
 }
 
+#ifdef CONFIG_PROC_FS
+static int timer_list_show(struct seq_file *m, void *v)
+{
+	struct timer_list_iter *iter = v;
+
+	if (iter->cpu == -1 && !iter->second_pass)
+		timer_list_header(m, iter->now);
+	else if (!iter->second_pass)
+		print_cpu(m, iter->cpu, iter->now);
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+	else if (iter->cpu == -1 && iter->second_pass)
+		timer_list_show_tickdevices_header(m);
+	else
+		print_tickdevice(m, tick_get_device(iter->cpu), iter->cpu);
+#endif
+	return 0;
+}
+
 static void *move_iter(struct timer_list_iter *iter, loff_t offset)
 {
 	for (; offset; offset--) {
@@ -395,3 +396,4 @@ static int __init init_timer_list_procfs(void)
 	return 0;
 }
 __initcall(init_timer_list_procfs);
+#endif
-- 
2.20.1

[PATCH AUTOSEL 4.14 065/105] acpi/arm64: ignore 5.1 FADTs that are reported as 5.0

[Sasha Levin]

From: Ard Biesheuvel <ard.biesheuvel@linaro.org>

[ Upstream commit 2af22f3ec3ca452f1e79b967f634708ff01ced8a ]

Some Qualcomm Snapdragon based laptops built to run Microsoft Windows
are clearly ACPI 5.1 based, given that that is the first ACPI revision
that supports ARM, and introduced the FADT 'arm_boot_flags' field,
which has a non-zero field on those systems.

So in these cases, infer from the ARM boot flags that the FADT must be
5.1 or later, and treat it as 5.1.

Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/kernel/acpi.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/kernel/acpi.c b/arch/arm64/kernel/acpi.c
index b3162715ed78..285f0b4851fc 100644
--- a/arch/arm64/kernel/acpi.c
+++ b/arch/arm64/kernel/acpi.c
@@ -157,10 +157,14 @@ static int __init acpi_fadt_sanity_check(void)
 	 */
 	if (table->revision < 5 ||
 	   (table->revision == 5 && fadt->minor_revision < 1)) {
-		pr_err("Unsupported FADT revision %d.%d, should be 5.1+\n",
+		pr_err(FW_BUG "Unsupported FADT revision %d.%d, should be 5.1+\n",
 		       table->revision, fadt->minor_revision);
-		ret = -EINVAL;
-		goto out;
+
+		if (!fadt->arm_boot_flags) {
+			ret = -EINVAL;
+			goto out;
+		}
+		pr_err("FADT has ARM boot flags set, assuming 5.1\n");
 	}
 
 	if (!(fadt->flags & ACPI_FADT_HW_REDUCED)) {
-- 
2.20.1

[PATCH AUTOSEL 4.14 066/105] media: coda: fix mpeg2 sequence number handling

[Sasha Levin]

From: Philipp Zabel <p.zabel@pengutronix.de>

[ Upstream commit 56d159a4ec6d8da7313aac6fcbb95d8fffe689ba ]

Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/coda/coda-bit.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/media/platform/coda/coda-bit.c b/drivers/media/platform/coda/coda-bit.c
index 6eee55430d46..43eb5d51cf23 100644
--- a/drivers/media/platform/coda/coda-bit.c
+++ b/drivers/media/platform/coda/coda-bit.c
@@ -1679,6 +1679,7 @@ static int __coda_start_decoding(struct coda_ctx *ctx)
 		v4l2_err(&dev->v4l2_dev, "CODA_COMMAND_SEQ_INIT timeout\n");
 		return ret;
 	}
+	ctx->sequence_offset = ~0U;
 	ctx->initialized = 1;
 
 	/* Update kfifo out pointer from coda bitstream read pointer */
@@ -2095,7 +2096,9 @@ static void coda_finish_decode(struct coda_ctx *ctx)
 		v4l2_err(&dev->v4l2_dev,
 			 "decoded frame index out of range: %d\n", decoded_idx);
 	} else {
-		val = coda_read(dev, CODA_RET_DEC_PIC_FRAME_NUM) - 1;
+		val = coda_read(dev, CODA_RET_DEC_PIC_FRAME_NUM);
+		if (ctx->sequence_offset == -1)
+			ctx->sequence_offset = val;
 		val -= ctx->sequence_offset;
 		spin_lock_irqsave(&ctx->buffer_meta_lock, flags);
 		if (!list_empty(&ctx->buffer_meta_list)) {
-- 
2.20.1

[PATCH AUTOSEL 4.14 067/105] media: coda: fix last buffer handling in V4L2_ENC_CMD_STOP

[Sasha Levin]

From: Marco Felsch <m.felsch@pengutronix.de>

[ Upstream commit f3775f89852d167990b0d718587774cf00d22ac2 ]

coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.

In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.

Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/coda/coda-common.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/media/platform/coda/coda-common.c b/drivers/media/platform/coda/coda-common.c
index 2e1472fadc2c..5b87c488ee11 100644
--- a/drivers/media/platform/coda/coda-common.c
+++ b/drivers/media/platform/coda/coda-common.c
@@ -932,6 +932,8 @@ static int coda_encoder_cmd(struct file *file, void *fh,
 	/* Set the stream-end flag on this context */
 	ctx->bit_stream_param |= CODA_BIT_STREAM_END_FLAG;
 
+	flush_work(&ctx->pic_run_work);
+
 	/* If there is no buffer in flight, wake up */
 	if (!ctx->streamon_out || ctx->qsequence == ctx->osequence) {
 		dst_vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx,
-- 
2.20.1

[PATCH AUTOSEL 4.14 068/105] media: coda: increment sequence offset for the last returned frame

[Sasha Levin]

From: Philipp Zabel <p.zabel@pengutronix.de>

[ Upstream commit b3b7d96817cdb8b6fc353867705275dce8f41ccc ]

If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/coda/coda-bit.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/media/platform/coda/coda-bit.c b/drivers/media/platform/coda/coda-bit.c
index 43eb5d51cf23..f0f2175265a9 100644
--- a/drivers/media/platform/coda/coda-bit.c
+++ b/drivers/media/platform/coda/coda-bit.c
@@ -2091,6 +2091,9 @@ static void coda_finish_decode(struct coda_ctx *ctx)
 		else if (ctx->display_idx < 0)
 			ctx->hold = true;
 	} else if (decoded_idx == -2) {
+		if (ctx->display_idx >= 0 &&
+		    ctx->display_idx < ctx->num_internal_frames)
+			ctx->sequence_offset++;
 		/* no frame was decoded, we still return remaining buffers */
 	} else if (decoded_idx < 0 || decoded_idx >= ctx->num_internal_frames) {
 		v4l2_err(&dev->v4l2_dev,
-- 
2.20.1

[PATCH AUTOSEL 4.14 069/105] media: vimc: cap: check v4l2_fill_pixfmt return value

[Sasha Levin]

From: André Almeida <andrealmeid@collabora.com>

[ Upstream commit 77ae46e11df5c96bb4582633851f838f5d954df4 ]

v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is
invalid or if the user is trying to use a multiplanar format with the
singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such
value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns
an error value if vimc_cap_try_fmt_vid_cap() has failed.

Signed-off-by: André Almeida <andrealmeid@collabora.com>
Suggested-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/vimc/vimc-capture.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/media/platform/vimc/vimc-capture.c b/drivers/media/platform/vimc/vimc-capture.c
index a078ad18909a..091921ed09dd 100644
--- a/drivers/media/platform/vimc/vimc-capture.c
+++ b/drivers/media/platform/vimc/vimc-capture.c
@@ -131,12 +131,15 @@ static int vimc_cap_s_fmt_vid_cap(struct file *file, void *priv,
 				  struct v4l2_format *f)
 {
 	struct vimc_cap_device *vcap = video_drvdata(file);
+	int ret;
 
 	/* Do not change the format while stream is on */
 	if (vb2_is_busy(&vcap->queue))
 		return -EBUSY;
 
-	vimc_cap_try_fmt_vid_cap(file, priv, f);
+	ret = vimc_cap_try_fmt_vid_cap(file, priv, f);
+	if (ret)
+		return ret;
 
 	dev_dbg(vcap->dev, "%s: format update: "
 		"old:%dx%d (0x%x, %d, %d, %d, %d) "
-- 
2.20.1

[PATCH AUTOSEL 4.14 070/105] media: hdpvr: fix locking and a missing msleep

[Sasha Levin]

From: Hans Verkuil <hverkuil@xs4all.nl>

[ Upstream commit 6bc5a4a1927556ff9adce1aa95ea408c95453225 ]

This driver has three locking issues:

- The wait_event_interruptible() condition calls hdpvr_get_next_buffer(dev)
  which uses a mutex, which is not allowed. Rewrite with list_empty_careful()
  that doesn't need locking.

- In hdpvr_read() the call to hdpvr_stop_streaming() didn't lock io_mutex,
  but it should have since stop_streaming expects that.

- In hdpvr_device_release() io_mutex was locked when calling flush_work(),
  but there it shouldn't take that mutex since the work done by flush_work()
  also wants to lock that mutex.

There are also two other changes (suggested by Keith):

- msecs_to_jiffies(4000); (a NOP) should have been msleep(4000).
- Change v4l2_dbg to v4l2_info to always log if streaming had to be restarted.

Reported-by: Keith Pyle <kpyle@austin.rr.com>
Suggested-by: Keith Pyle <kpyle@austin.rr.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/hdpvr/hdpvr-video.c | 17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)

diff --git a/drivers/media/usb/hdpvr/hdpvr-video.c b/drivers/media/usb/hdpvr/hdpvr-video.c
index 7fb036d6a86e..991f820a4530 100644
--- a/drivers/media/usb/hdpvr/hdpvr-video.c
+++ b/drivers/media/usb/hdpvr/hdpvr-video.c
@@ -439,7 +439,7 @@ static ssize_t hdpvr_read(struct file *file, char __user *buffer, size_t count,
 	/* wait for the first buffer */
 	if (!(file->f_flags & O_NONBLOCK)) {
 		if (wait_event_interruptible(dev->wait_data,
-					     hdpvr_get_next_buffer(dev)))
+					     !list_empty_careful(&dev->rec_buff_list)))
 			return -ERESTARTSYS;
 	}
 
@@ -465,10 +465,17 @@ static ssize_t hdpvr_read(struct file *file, char __user *buffer, size_t count,
 				goto err;
 			}
 			if (!err) {
-				v4l2_dbg(MSG_INFO, hdpvr_debug, &dev->v4l2_dev,
-					"timeout: restart streaming\n");
+				v4l2_info(&dev->v4l2_dev,
+					  "timeout: restart streaming\n");
+				mutex_lock(&dev->io_mutex);
 				hdpvr_stop_streaming(dev);
-				msecs_to_jiffies(4000);
+				mutex_unlock(&dev->io_mutex);
+				/*
+				 * The FW needs about 4 seconds after streaming
+				 * stopped before it is ready to restart
+				 * streaming.
+				 */
+				msleep(4000);
 				err = hdpvr_start_streaming(dev);
 				if (err) {
 					ret = err;
@@ -1133,9 +1140,7 @@ static void hdpvr_device_release(struct video_device *vdev)
 	struct hdpvr_device *dev = video_get_drvdata(vdev);
 
 	hdpvr_delete(dev);
-	mutex_lock(&dev->io_mutex);
 	flush_work(&dev->worker);
-	mutex_unlock(&dev->io_mutex);
 
 	v4l2_device_unregister(&dev->v4l2_dev);
 	v4l2_ctrl_handler_free(&dev->hdl);
-- 
2.20.1

[PATCH AUTOSEL 4.14 071/105] rtlwifi: rtl8192cu: fix error handle when usb probe failed

[Sasha Levin]

From: Ping-Ke Shih <pkshih@realtek.com>

[ Upstream commit 6c0ed66f1a5b84e2a812c7c2d6571a5621bf3396 ]

rtl_usb_probe() must do error handle rtl_deinit_core() only if
rtl_init_core() is done, otherwise goto error_out2.

| usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
| rtl_usb: reg 0xf0, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0
| rtl8192cu: Chip version 0x10
| rtl_usb: reg 0xa, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x0
| rtl_usb: Too few input end points found
| INFO: trying to register non-static key.
| the code is fine but needs lockdep annotation.
| turning off the locking correctness validator.
| CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
| Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
| Google 01/01/2011
| Workqueue: usb_hub_wq hub_event
| Call Trace:
|   __dump_stack lib/dump_stack.c:77 [inline]
|   dump_stack+0xe8/0x16e lib/dump_stack.c:113
|   assign_lock_key kernel/locking/lockdep.c:786 [inline]
|   register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
|   __lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
|   lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
|   __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
|   _raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
|   rtl_c2hcmd_launcher+0xd1/0x390
| drivers/net/wireless/realtek/rtlwifi/base.c:2344
|   rtl_deinit_core+0x25/0x2d0 drivers/net/wireless/realtek/rtlwifi/base.c:574
|   rtl_usb_probe.cold+0x861/0xa70
| drivers/net/wireless/realtek/rtlwifi/usb.c:1093
|   usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
|   really_probe+0x2da/0xb10 drivers/base/dd.c:509
|   driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
|   __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
|   bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
|   __device_attach+0x223/0x3a0 drivers/base/dd.c:844
|   bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
|   device_add+0xad2/0x16e0 drivers/base/core.c:2106
|   usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
|   generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
|   usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
|   really_probe+0x2da/0xb10 drivers/base/dd.c:509
|   driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
|   __device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
|   bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
|   __device_attach+0x223/0x3a0 drivers/base/dd.c:844
|   bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
|   device_add+0xad2/0x16e0 drivers/base/core.c:2106
|   usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
|   hub_port_connect drivers/usb/core/hub.c:5089 [inline]
|   hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
|   port_event drivers/usb/core/hub.c:5350 [inline]
|   hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
|   process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
|   worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
|   kthread+0x313/0x420 kernel/kthread.c:253
|   ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352

Reported-by: syzbot+1fcc5ef45175fc774231@syzkaller.appspotmail.com
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/realtek/rtlwifi/usb.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/realtek/rtlwifi/usb.c b/drivers/net/wireless/realtek/rtlwifi/usb.c
index 820c42ff5384..2401c8bdb211 100644
--- a/drivers/net/wireless/realtek/rtlwifi/usb.c
+++ b/drivers/net/wireless/realtek/rtlwifi/usb.c
@@ -1099,13 +1099,13 @@ int rtl_usb_probe(struct usb_interface *intf,
 	rtlpriv->cfg->ops->read_eeprom_info(hw);
 	err = _rtl_usb_init(hw);
 	if (err)
-		goto error_out;
+		goto error_out2;
 	rtl_usb_init_sw(hw);
 	/* Init mac80211 sw */
 	err = rtl_init_core(hw);
 	if (err) {
 		pr_err("Can't allocate sw for mac80211\n");
-		goto error_out;
+		goto error_out2;
 	}
 	if (rtlpriv->cfg->ops->init_sw_vars(hw)) {
 		pr_err("Can't init_sw_vars\n");
@@ -1126,6 +1126,7 @@ int rtl_usb_probe(struct usb_interface *intf,
 
 error_out:
 	rtl_deinit_core(hw);
+error_out2:
 	_rtl_usb_io_handler_release(hw);
 	usb_put_dev(udev);
 	complete(&rtlpriv->firmware_loading_complete);
-- 
2.20.1

[PATCH AUTOSEL 4.14 072/105] mt7601u: do not schedule rx_tasklet when the device has been disconnected

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 4079e8ccabc3b6d1b503f2376123cb515d14921f ]

Do not schedule rx_tasklet when the usb dongle is disconnected.
Moreover do not grub rx_lock in mt7601u_kill_rx since usb_poison_urb
can run concurrently with urb completion and we can unlink urbs from rx
ring in any order.
This patch fixes the common kernel warning reported when
the device is removed.

[   24.921354] usb 3-14: USB disconnect, device number 7
[   24.921593] ------------[ cut here ]------------
[   24.921594] RX urb mismatch
[   24.921675] WARNING: CPU: 4 PID: 163 at drivers/net/wireless/mediatek/mt7601u/dma.c:200 mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921769] CPU: 4 PID: 163 Comm: kworker/4:2 Tainted: G           OE     4.19.31-041931-generic #201903231635
[   24.921770] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P1.30 05/23/2014
[   24.921782] Workqueue: usb_hub_wq hub_event
[   24.921797] RIP: 0010:mt7601u_complete_rx+0xcb/0xd0 [mt7601u]
[   24.921800] RSP: 0018:ffff9bd9cfd03d08 EFLAGS: 00010086
[   24.921802] RAX: 0000000000000000 RBX: ffff9bd9bf043540 RCX: 0000000000000006
[   24.921803] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9bd9cfd16420
[   24.921804] RBP: ffff9bd9cfd03d28 R08: 0000000000000002 R09: 00000000000003a8
[   24.921805] R10: 0000002f485fca34 R11: 0000000000000000 R12: ffff9bd9bf043c1c
[   24.921806] R13: ffff9bd9c62fa3c0 R14: 0000000000000082 R15: 0000000000000000
[   24.921807] FS:  0000000000000000(0000) GS:ffff9bd9cfd00000(0000) knlGS:0000000000000000
[   24.921808] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   24.921808] CR2: 00007fb2648b0000 CR3: 0000000142c0a004 CR4: 00000000001606e0
[   24.921809] Call Trace:
[   24.921812]  <IRQ>
[   24.921819]  __usb_hcd_giveback_urb+0x8b/0x140
[   24.921821]  usb_hcd_giveback_urb+0xca/0xe0
[   24.921828]  xhci_giveback_urb_in_irq.isra.42+0x82/0xf0
[   24.921834]  handle_cmd_completion+0xe02/0x10d0
[   24.921837]  xhci_irq+0x274/0x4a0
[   24.921838]  xhci_msi_irq+0x11/0x20
[   24.921851]  __handle_irq_event_percpu+0x44/0x190
[   24.921856]  handle_irq_event_percpu+0x32/0x80
[   24.921861]  handle_irq_event+0x3b/0x5a
[   24.921867]  handle_edge_irq+0x80/0x190
[   24.921874]  handle_irq+0x20/0x30
[   24.921889]  do_IRQ+0x4e/0xe0
[   24.921891]  common_interrupt+0xf/0xf
[   24.921892]  </IRQ>
[   24.921900] RIP: 0010:usb_hcd_flush_endpoint+0x78/0x180
[   24.921354] usb 3-14: USB disconnect, device number 7

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 33 +++++++++++----------
 1 file changed, 18 insertions(+), 15 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index 7f3e3983b781..bc36712cfffc 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -193,10 +193,23 @@ static void mt7601u_complete_rx(struct urb *urb)
 	struct mt7601u_rx_queue *q = &dev->rx_q;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
+	/* do no schedule rx tasklet if urb has been unlinked
+	 * or the device has been removed
+	 */
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "rx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: RX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->rx_lock, flags);
 	if (WARN_ONCE(q->e[q->end].urb != urb, "RX urb mismatch"))
 		goto out;
 
@@ -363,19 +376,9 @@ int mt7601u_dma_enqueue_tx(struct mt7601u_dev *dev, struct sk_buff *skb,
 static void mt7601u_kill_rx(struct mt7601u_dev *dev)
 {
 	int i;
-	unsigned long flags;
 
-	spin_lock_irqsave(&dev->rx_lock, flags);
-
-	for (i = 0; i < dev->rx_q.entries; i++) {
-		int next = dev->rx_q.end;
-
-		spin_unlock_irqrestore(&dev->rx_lock, flags);
-		usb_poison_urb(dev->rx_q.e[next].urb);
-		spin_lock_irqsave(&dev->rx_lock, flags);
-	}
-
-	spin_unlock_irqrestore(&dev->rx_lock, flags);
+	for (i = 0; i < dev->rx_q.entries; i++)
+		usb_poison_urb(dev->rx_q.e[i].urb);
 }
 
 static int mt7601u_submit_rx_buf(struct mt7601u_dev *dev,
-- 
2.20.1

[PATCH AUTOSEL 4.14 073/105] x86/build: Add 'set -e' to mkcapflags.sh to delete broken capflags.c

[Sasha Levin]

From: Masahiro Yamada <yamada.masahiro@socionext.com>

[ Upstream commit bc53d3d777f81385c1bb08b07bd1c06450ecc2c1 ]

Without 'set -e', shell scripts continue running even after any
error occurs. The missed 'set -e' is a typical bug in shell scripting.

For example, when a disk space shortage occurs while this script is
running, it actually ends up with generating a truncated capflags.c.

Yet, mkcapflags.sh continues running and exits with 0. So, the build
system assumes it has succeeded.

It will not be re-generated in the next invocation of Make since its
timestamp is newer than that of any of the source files.

Add 'set -e' so that any error in this script is caught and propagated
to the build system.

Since 9c2af1c7377a ("kbuild: add .DELETE_ON_ERROR special target"),
make automatically deletes the target on any failure. So, the broken
capflags.c will be deleted automatically.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190625072622.17679-1-yamada.masahiro@socionext.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/cpu/mkcapflags.sh | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/x86/kernel/cpu/mkcapflags.sh b/arch/x86/kernel/cpu/mkcapflags.sh
index d0dfb892c72f..aed45b8895d5 100644
--- a/arch/x86/kernel/cpu/mkcapflags.sh
+++ b/arch/x86/kernel/cpu/mkcapflags.sh
@@ -4,6 +4,8 @@
 # Generate the x86_cap/bug_flags[] arrays from include/asm/cpufeatures.h
 #
 
+set -e
+
 IN=$1
 OUT=$2
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 074/105] mt7601u: fix possible memory leak when the device is disconnected

[Sasha Levin]

From: Lorenzo Bianconi <lorenzo@kernel.org>

[ Upstream commit 23377c200b2eb48a60d0f228b2a2e75ed6ee6060 ]

When the device is disconnected while passing traffic it is possible
to receive out of order urbs causing a memory leak since the skb linked
to the current tx urb is not removed. Fix the issue deallocating the skb
cleaning up the tx ring. Moreover this patch fixes the following kernel
warning

[   57.480771] usb 1-1: USB disconnect, device number 2
[   57.483451] ------------[ cut here ]------------
[   57.483462] TX urb mismatch
[   57.483481] WARNING: CPU: 1 PID: 32 at drivers/net/wireless/mediatek/mt7601u/dma.c:245 mt7601u_complete_tx+0x165/00
[   57.483483] Modules linked in:
[   57.483496] CPU: 1 PID: 32 Comm: kworker/1:1 Not tainted 5.2.0-rc1+ #72
[   57.483498] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.12.0-2.fc30 04/01/2014
[   57.483502] Workqueue: usb_hub_wq hub_event
[   57.483507] RIP: 0010:mt7601u_complete_tx+0x165/0x1e0
[   57.483510] Code: 8b b5 10 04 00 00 8b 8d 14 04 00 00 eb 8b 80 3d b1 cb e1 00 00 75 9e 48 c7 c7 a4 ea 05 82 c6 05 f
[   57.483513] RSP: 0000:ffffc900000a0d28 EFLAGS: 00010092
[   57.483516] RAX: 000000000000000f RBX: ffff88802c0a62c0 RCX: ffffc900000a0c2c
[   57.483518] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff810a8371
[   57.483520] RBP: ffff88803ced6858 R08: 0000000000000000 R09: 0000000000000001
[   57.483540] R10: 0000000000000002 R11: 0000000000000000 R12: 0000000000000046
[   57.483542] R13: ffff88802c0a6c88 R14: ffff88803baab540 R15: ffff88803a0cc078
[   57.483548] FS:  0000000000000000(0000) GS:ffff88803eb00000(0000) knlGS:0000000000000000
[   57.483550] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   57.483552] CR2: 000055e7f6780100 CR3: 0000000028c86000 CR4: 00000000000006a0
[   57.483554] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   57.483556] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   57.483559] Call Trace:
[   57.483561]  <IRQ>
[   57.483565]  __usb_hcd_giveback_urb+0x77/0xe0
[   57.483570]  xhci_giveback_urb_in_irq.isra.0+0x8b/0x140
[   57.483574]  handle_cmd_completion+0xf5b/0x12c0
[   57.483577]  xhci_irq+0x1f6/0x1810
[   57.483581]  ? lockdep_hardirqs_on+0x9e/0x180
[   57.483584]  ? _raw_spin_unlock_irq+0x24/0x30
[   57.483588]  __handle_irq_event_percpu+0x3a/0x260
[   57.483592]  handle_irq_event_percpu+0x1c/0x60
[   57.483595]  handle_irq_event+0x2f/0x4c
[   57.483599]  handle_edge_irq+0x7e/0x1a0
[   57.483603]  handle_irq+0x17/0x20
[   57.483607]  do_IRQ+0x54/0x110
[   57.483610]  common_interrupt+0xf/0xf
[   57.483612]  </IRQ>

Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt7601u/dma.c | 21 ++++++++++++++++-----
 drivers/net/wireless/mediatek/mt7601u/tx.c  |  4 ++--
 2 files changed, 18 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt7601u/dma.c b/drivers/net/wireless/mediatek/mt7601u/dma.c
index bc36712cfffc..47cebb2ec05c 100644
--- a/drivers/net/wireless/mediatek/mt7601u/dma.c
+++ b/drivers/net/wireless/mediatek/mt7601u/dma.c
@@ -241,14 +241,25 @@ static void mt7601u_complete_tx(struct urb *urb)
 	struct sk_buff *skb;
 	unsigned long flags;
 
-	spin_lock_irqsave(&dev->tx_lock, flags);
+	switch (urb->status) {
+	case -ECONNRESET:
+	case -ESHUTDOWN:
+	case -ENOENT:
+		return;
+	default:
+		dev_err_ratelimited(dev->dev, "tx urb failed: %d\n",
+				    urb->status);
+		/* fall through */
+	case 0:
+		break;
+	}
 
-	if (mt7601u_urb_has_error(urb))
-		dev_err(dev->dev, "Error: TX urb failed:%d\n", urb->status);
+	spin_lock_irqsave(&dev->tx_lock, flags);
 	if (WARN_ONCE(q->e[q->start].urb != urb, "TX urb mismatch"))
 		goto out;
 
 	skb = q->e[q->start].skb;
+	q->e[q->start].skb = NULL;
 	trace_mt_tx_dma_done(dev, skb);
 
 	__skb_queue_tail(&dev->tx_skb_done, skb);
@@ -448,10 +459,10 @@ static void mt7601u_free_tx_queue(struct mt7601u_tx_queue *q)
 {
 	int i;
 
-	WARN_ON(q->used);
-
 	for (i = 0; i < q->entries; i++)  {
 		usb_poison_urb(q->e[i].urb);
+		if (q->e[i].skb)
+			mt7601u_tx_status(q->dev, q->e[i].skb);
 		usb_free_urb(q->e[i].urb);
 	}
 }
diff --git a/drivers/net/wireless/mediatek/mt7601u/tx.c b/drivers/net/wireless/mediatek/mt7601u/tx.c
index 3600e911a63e..4d81c45722fb 100644
--- a/drivers/net/wireless/mediatek/mt7601u/tx.c
+++ b/drivers/net/wireless/mediatek/mt7601u/tx.c
@@ -117,9 +117,9 @@ void mt7601u_tx_status(struct mt7601u_dev *dev, struct sk_buff *skb)
 	info->status.rates[0].idx = -1;
 	info->flags |= IEEE80211_TX_STAT_ACK;
 
-	spin_lock(&dev->mac_lock);
+	spin_lock_bh(&dev->mac_lock);
 	ieee80211_tx_status(dev->hw, skb);
-	spin_unlock(&dev->mac_lock);
+	spin_unlock_bh(&dev->mac_lock);
 }
 
 static int mt7601u_skb_rooms(struct mt7601u_dev *dev, struct sk_buff *skb)
-- 
2.20.1

[PATCH AUTOSEL 4.14 075/105] ipvs: fix tinfo memory leak in start_sync_thread

[Sasha Levin]

From: Julian Anastasov <ja@ssi.bg>

[ Upstream commit 5db7c8b9f9fc2aeec671ae3ca6375752c162e0e7 ]

syzkaller reports for memory leak in start_sync_thread [1]

As Eric points out, kthread may start and stop before the
threadfn function is called, so there is no chance the
data (tinfo in our case) to be released in thread.

Fix this by releasing tinfo in the controlling code instead.

[1]
BUG: memory leak
unreferenced object 0xffff8881206bf700 (size 32):
 comm "syz-executor761", pid 7268, jiffies 4294943441 (age 20.470s)
 hex dump (first 32 bytes):
   00 40 7c 09 81 88 ff ff 80 45 b8 21 81 88 ff ff  .@|......E.!....
   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
 backtrace:
   [<0000000057619e23>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline]
   [<0000000057619e23>] slab_post_alloc_hook mm/slab.h:439 [inline]
   [<0000000057619e23>] slab_alloc mm/slab.c:3326 [inline]
   [<0000000057619e23>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553
   [<0000000086ce5479>] kmalloc include/linux/slab.h:547 [inline]
   [<0000000086ce5479>] start_sync_thread+0x5d2/0xe10 net/netfilter/ipvs/ip_vs_sync.c:1862
   [<000000001a9229cc>] do_ip_vs_set_ctl+0x4c5/0x780 net/netfilter/ipvs/ip_vs_ctl.c:2402
   [<00000000ece457c8>] nf_sockopt net/netfilter/nf_sockopt.c:106 [inline]
   [<00000000ece457c8>] nf_setsockopt+0x4c/0x80 net/netfilter/nf_sockopt.c:115
   [<00000000942f62d4>] ip_setsockopt net/ipv4/ip_sockglue.c:1258 [inline]
   [<00000000942f62d4>] ip_setsockopt+0x9b/0xb0 net/ipv4/ip_sockglue.c:1238
   [<00000000a56a8ffd>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616
   [<00000000fa895401>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130
   [<0000000095eef4cf>] __sys_setsockopt+0x98/0x120 net/socket.c:2078
   [<000000009747cf88>] __do_sys_setsockopt net/socket.c:2089 [inline]
   [<000000009747cf88>] __se_sys_setsockopt net/socket.c:2086 [inline]
   [<000000009747cf88>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086
   [<00000000ded8ba80>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301
   [<00000000893b4ac8>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

Reported-by: syzbot+7e2e50c8adfccd2e5041@syzkaller.appspotmail.com
Suggested-by: Eric Biggers <ebiggers@kernel.org>
Fixes: 998e7a76804b ("ipvs: Use kthread_run() instead of doing a double-fork via kernel_thread()")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/net/ip_vs.h             |   6 +-
 net/netfilter/ipvs/ip_vs_ctl.c  |   4 -
 net/netfilter/ipvs/ip_vs_sync.c | 134 +++++++++++++++++---------------
 3 files changed, 76 insertions(+), 68 deletions(-)

diff --git a/include/net/ip_vs.h b/include/net/ip_vs.h
index 5d08c1950e7d..82bc9f0e8a76 100644
--- a/include/net/ip_vs.h
+++ b/include/net/ip_vs.h
@@ -812,11 +812,12 @@ struct ipvs_master_sync_state {
 	struct ip_vs_sync_buff	*sync_buff;
 	unsigned long		sync_queue_len;
 	unsigned int		sync_queue_delay;
-	struct task_struct	*master_thread;
 	struct delayed_work	master_wakeup_work;
 	struct netns_ipvs	*ipvs;
 };
 
+struct ip_vs_sync_thread_data;
+
 /* How much time to keep dests in trash */
 #define IP_VS_DEST_TRASH_PERIOD		(120 * HZ)
 
@@ -947,7 +948,8 @@ struct netns_ipvs {
 	spinlock_t		sync_lock;
 	struct ipvs_master_sync_state *ms;
 	spinlock_t		sync_buff_lock;
-	struct task_struct	**backup_threads;
+	struct ip_vs_sync_thread_data *master_tinfo;
+	struct ip_vs_sync_thread_data *backup_tinfo;
 	int			threads_mask;
 	volatile int		sync_state;
 	struct mutex		sync_mutex;
diff --git a/net/netfilter/ipvs/ip_vs_ctl.c b/net/netfilter/ipvs/ip_vs_ctl.c
index 6d7608b88f66..4648dccebf59 100644
--- a/net/netfilter/ipvs/ip_vs_ctl.c
+++ b/net/netfilter/ipvs/ip_vs_ctl.c
@@ -2414,9 +2414,7 @@ do_ip_vs_set_ctl(struct sock *sk, int cmd, void __user *user, unsigned int len)
 			cfg.syncid = dm->syncid;
 			ret = start_sync_thread(ipvs, &cfg, dm->state);
 		} else {
-			mutex_lock(&ipvs->sync_mutex);
 			ret = stop_sync_thread(ipvs, dm->state);
-			mutex_unlock(&ipvs->sync_mutex);
 		}
 		goto out_dec;
 	}
@@ -3524,10 +3522,8 @@ static int ip_vs_genl_del_daemon(struct netns_ipvs *ipvs, struct nlattr **attrs)
 	if (!attrs[IPVS_DAEMON_ATTR_STATE])
 		return -EINVAL;
 
-	mutex_lock(&ipvs->sync_mutex);
 	ret = stop_sync_thread(ipvs,
 			       nla_get_u32(attrs[IPVS_DAEMON_ATTR_STATE]));
-	mutex_unlock(&ipvs->sync_mutex);
 	return ret;
 }
 
diff --git a/net/netfilter/ipvs/ip_vs_sync.c b/net/netfilter/ipvs/ip_vs_sync.c
index 5e07f7a6794e..b578ebb3d7ef 100644
--- a/net/netfilter/ipvs/ip_vs_sync.c
+++ b/net/netfilter/ipvs/ip_vs_sync.c
@@ -195,6 +195,7 @@ union ip_vs_sync_conn {
 #define IPVS_OPT_F_PARAM	(1 << (IPVS_OPT_PARAM-1))
 
 struct ip_vs_sync_thread_data {
+	struct task_struct *task;
 	struct netns_ipvs *ipvs;
 	struct socket *sock;
 	char *buf;
@@ -374,8 +375,11 @@ static inline void sb_queue_tail(struct netns_ipvs *ipvs,
 					      max(IPVS_SYNC_SEND_DELAY, 1));
 		ms->sync_queue_len++;
 		list_add_tail(&sb->list, &ms->sync_queue);
-		if ((++ms->sync_queue_delay) == IPVS_SYNC_WAKEUP_RATE)
-			wake_up_process(ms->master_thread);
+		if ((++ms->sync_queue_delay) == IPVS_SYNC_WAKEUP_RATE) {
+			int id = (int)(ms - ipvs->ms);
+
+			wake_up_process(ipvs->master_tinfo[id].task);
+		}
 	} else
 		ip_vs_sync_buff_release(sb);
 	spin_unlock(&ipvs->sync_lock);
@@ -1645,8 +1649,10 @@ static void master_wakeup_work_handler(struct work_struct *work)
 	spin_lock_bh(&ipvs->sync_lock);
 	if (ms->sync_queue_len &&
 	    ms->sync_queue_delay < IPVS_SYNC_WAKEUP_RATE) {
+		int id = (int)(ms - ipvs->ms);
+
 		ms->sync_queue_delay = IPVS_SYNC_WAKEUP_RATE;
-		wake_up_process(ms->master_thread);
+		wake_up_process(ipvs->master_tinfo[id].task);
 	}
 	spin_unlock_bh(&ipvs->sync_lock);
 }
@@ -1712,10 +1718,6 @@ static int sync_thread_master(void *data)
 	if (sb)
 		ip_vs_sync_buff_release(sb);
 
-	/* release the sending multicast socket */
-	sock_release(tinfo->sock);
-	kfree(tinfo);
-
 	return 0;
 }
 
@@ -1749,11 +1751,6 @@ static int sync_thread_backup(void *data)
 		}
 	}
 
-	/* release the sending multicast socket */
-	sock_release(tinfo->sock);
-	kfree(tinfo->buf);
-	kfree(tinfo);
-
 	return 0;
 }
 
@@ -1761,8 +1758,8 @@ static int sync_thread_backup(void *data)
 int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
 		      int state)
 {
-	struct ip_vs_sync_thread_data *tinfo = NULL;
-	struct task_struct **array = NULL, *task;
+	struct ip_vs_sync_thread_data *ti = NULL, *tinfo;
+	struct task_struct *task;
 	struct net_device *dev;
 	char *name;
 	int (*threadfn)(void *data);
@@ -1831,7 +1828,7 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
 		threadfn = sync_thread_master;
 	} else if (state == IP_VS_STATE_BACKUP) {
 		result = -EEXIST;
-		if (ipvs->backup_threads)
+		if (ipvs->backup_tinfo)
 			goto out_early;
 
 		ipvs->bcfg = *c;
@@ -1858,28 +1855,22 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
 					  master_wakeup_work_handler);
 			ms->ipvs = ipvs;
 		}
-	} else {
-		array = kcalloc(count, sizeof(struct task_struct *),
-				GFP_KERNEL);
-		result = -ENOMEM;
-		if (!array)
-			goto out;
 	}
+	result = -ENOMEM;
+	ti = kcalloc(count, sizeof(struct ip_vs_sync_thread_data),
+		     GFP_KERNEL);
+	if (!ti)
+		goto out;
 
 	for (id = 0; id < count; id++) {
-		result = -ENOMEM;
-		tinfo = kmalloc(sizeof(*tinfo), GFP_KERNEL);
-		if (!tinfo)
-			goto out;
+		tinfo = &ti[id];
 		tinfo->ipvs = ipvs;
-		tinfo->sock = NULL;
 		if (state == IP_VS_STATE_BACKUP) {
+			result = -ENOMEM;
 			tinfo->buf = kmalloc(ipvs->bcfg.sync_maxlen,
 					     GFP_KERNEL);
 			if (!tinfo->buf)
 				goto out;
-		} else {
-			tinfo->buf = NULL;
 		}
 		tinfo->id = id;
 		if (state == IP_VS_STATE_MASTER)
@@ -1894,17 +1885,15 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
 			result = PTR_ERR(task);
 			goto out;
 		}
-		tinfo = NULL;
-		if (state == IP_VS_STATE_MASTER)
-			ipvs->ms[id].master_thread = task;
-		else
-			array[id] = task;
+		tinfo->task = task;
 	}
 
 	/* mark as active */
 
-	if (state == IP_VS_STATE_BACKUP)
-		ipvs->backup_threads = array;
+	if (state == IP_VS_STATE_MASTER)
+		ipvs->master_tinfo = ti;
+	else
+		ipvs->backup_tinfo = ti;
 	spin_lock_bh(&ipvs->sync_buff_lock);
 	ipvs->sync_state |= state;
 	spin_unlock_bh(&ipvs->sync_buff_lock);
@@ -1919,29 +1908,31 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
 
 out:
 	/* We do not need RTNL lock anymore, release it here so that
-	 * sock_release below and in the kthreads can use rtnl_lock
-	 * to leave the mcast group.
+	 * sock_release below can use rtnl_lock to leave the mcast group.
 	 */
 	rtnl_unlock();
-	count = id;
-	while (count-- > 0) {
-		if (state == IP_VS_STATE_MASTER)
-			kthread_stop(ipvs->ms[count].master_thread);
-		else
-			kthread_stop(array[count]);
+	id = min(id, count - 1);
+	if (ti) {
+		for (tinfo = ti + id; tinfo >= ti; tinfo--) {
+			if (tinfo->task)
+				kthread_stop(tinfo->task);
+		}
 	}
 	if (!(ipvs->sync_state & IP_VS_STATE_MASTER)) {
 		kfree(ipvs->ms);
 		ipvs->ms = NULL;
 	}
 	mutex_unlock(&ipvs->sync_mutex);
-	if (tinfo) {
-		if (tinfo->sock)
-			sock_release(tinfo->sock);
-		kfree(tinfo->buf);
-		kfree(tinfo);
+
+	/* No more mutexes, release socks */
+	if (ti) {
+		for (tinfo = ti + id; tinfo >= ti; tinfo--) {
+			if (tinfo->sock)
+				sock_release(tinfo->sock);
+			kfree(tinfo->buf);
+		}
+		kfree(ti);
 	}
-	kfree(array);
 	return result;
 
 out_early:
@@ -1953,15 +1944,18 @@ int start_sync_thread(struct netns_ipvs *ipvs, struct ipvs_sync_daemon_cfg *c,
 
 int stop_sync_thread(struct netns_ipvs *ipvs, int state)
 {
-	struct task_struct **array;
+	struct ip_vs_sync_thread_data *ti, *tinfo;
 	int id;
 	int retc = -EINVAL;
 
 	IP_VS_DBG(7, "%s(): pid %d\n", __func__, task_pid_nr(current));
 
+	mutex_lock(&ipvs->sync_mutex);
 	if (state == IP_VS_STATE_MASTER) {
+		retc = -ESRCH;
 		if (!ipvs->ms)
-			return -ESRCH;
+			goto err;
+		ti = ipvs->master_tinfo;
 
 		/*
 		 * The lock synchronizes with sb_queue_tail(), so that we don't
@@ -1980,38 +1974,56 @@ int stop_sync_thread(struct netns_ipvs *ipvs, int state)
 			struct ipvs_master_sync_state *ms = &ipvs->ms[id];
 			int ret;
 
+			tinfo = &ti[id];
 			pr_info("stopping master sync thread %d ...\n",
-				task_pid_nr(ms->master_thread));
+				task_pid_nr(tinfo->task));
 			cancel_delayed_work_sync(&ms->master_wakeup_work);
-			ret = kthread_stop(ms->master_thread);
+			ret = kthread_stop(tinfo->task);
 			if (retc >= 0)
 				retc = ret;
 		}
 		kfree(ipvs->ms);
 		ipvs->ms = NULL;
+		ipvs->master_tinfo = NULL;
 	} else if (state == IP_VS_STATE_BACKUP) {
-		if (!ipvs->backup_threads)
-			return -ESRCH;
+		retc = -ESRCH;
+		if (!ipvs->backup_tinfo)
+			goto err;
+		ti = ipvs->backup_tinfo;
 
 		ipvs->sync_state &= ~IP_VS_STATE_BACKUP;
-		array = ipvs->backup_threads;
 		retc = 0;
 		for (id = ipvs->threads_mask; id >= 0; id--) {
 			int ret;
 
+			tinfo = &ti[id];
 			pr_info("stopping backup sync thread %d ...\n",
-				task_pid_nr(array[id]));
-			ret = kthread_stop(array[id]);
+				task_pid_nr(tinfo->task));
+			ret = kthread_stop(tinfo->task);
 			if (retc >= 0)
 				retc = ret;
 		}
-		kfree(array);
-		ipvs->backup_threads = NULL;
+		ipvs->backup_tinfo = NULL;
+	} else {
+		goto err;
 	}
+	id = ipvs->threads_mask;
+	mutex_unlock(&ipvs->sync_mutex);
+
+	/* No more mutexes, release socks */
+	for (tinfo = ti + id; tinfo >= ti; tinfo--) {
+		if (tinfo->sock)
+			sock_release(tinfo->sock);
+		kfree(tinfo->buf);
+	}
+	kfree(ti);
 
 	/* decrease the module use count */
 	ip_vs_use_count_dec();
+	return retc;
 
+err:
+	mutex_unlock(&ipvs->sync_mutex);
 	return retc;
 }
 
@@ -2030,7 +2042,6 @@ void ip_vs_sync_net_cleanup(struct netns_ipvs *ipvs)
 {
 	int retc;
 
-	mutex_lock(&ipvs->sync_mutex);
 	retc = stop_sync_thread(ipvs, IP_VS_STATE_MASTER);
 	if (retc && retc != -ESRCH)
 		pr_err("Failed to stop Master Daemon\n");
@@ -2038,5 +2049,4 @@ void ip_vs_sync_net_cleanup(struct netns_ipvs *ipvs)
 	retc = stop_sync_thread(ipvs, IP_VS_STATE_BACKUP);
 	if (retc && retc != -ESRCH)
 		pr_err("Failed to stop Backup Daemon\n");
-	mutex_unlock(&ipvs->sync_mutex);
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 076/105] ath10k: add missing error handling

[Sasha Levin]

From: Claire Chang <tientzu@chromium.org>

[ Upstream commit 4b553f3ca4cbde67399aa3a756c37eb92145b8a1 ]

In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.

Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28

Fixes: d96db25d2025 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/sdio.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index da9dbf3ddaa5..c6440d28ab48 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -610,6 +610,10 @@ static int ath10k_sdio_mbox_rx_alloc(struct ath10k *ar,
 						    full_len,
 						    last_in_bundle,
 						    last_in_bundle);
+		if (ret) {
+			ath10k_warn(ar, "alloc_rx_pkt error %d\n", ret);
+			goto err;
+		}
 	}
 
 	ar_sdio->n_rx_pkts = i;
-- 
2.20.1

[PATCH AUTOSEL 4.14 077/105] ath10k: fix PCIE device wake up failed

[Sasha Levin]

From: Miaoqing Pan <miaoqing@codeaurora.org>

[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ]

Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"

The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake

Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.

But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.

Tested HW: QCA9984

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/hw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/hw.c b/drivers/net/wireless/ath/ath10k/hw.c
index a860691d635d..e96534cd3d8b 100644
--- a/drivers/net/wireless/ath/ath10k/hw.c
+++ b/drivers/net/wireless/ath/ath10k/hw.c
@@ -168,7 +168,7 @@ const struct ath10k_hw_values qca6174_values = {
 };
 
 const struct ath10k_hw_values qca99x0_values = {
-	.rtc_state_val_on		= 5,
+	.rtc_state_val_on		= 7,
 	.ce_count			= 12,
 	.msi_assign_ce_max		= 12,
 	.num_target_ce_config_wlan	= 10,
-- 
2.20.1

[PATCH AUTOSEL 4.14 078/105] perf tools: Increase MAX_NR_CPUS and MAX_CACHES

[Sasha Levin]

From: Kyle Meyer <kyle.meyer@hpe.com>

[ Upstream commit 9f94c7f947e919c343b30f080285af53d0fa9902 ]

Attempting to profile 1024 or more CPUs with perf causes two errors:

  perf record -a
  [ perf record: Woken up X times to write data ]
  way too many cpu caches..
  [ perf record: Captured and wrote X MB perf.data (X samples) ]

  perf report -C 1024
  Error: failed to set  cpu bitmap
  Requested CPU 1024 too large. Consider raising MAX_NR_CPUS

  Increasing MAX_NR_CPUS from 1024 to 2048 and redefining MAX_CACHES as
  MAX_NR_CPUS * 4 returns normal functionality to perf:

  perf record -a
  [ perf record: Woken up X times to write data ]
  [ perf record: Captured and wrote X MB perf.data (X samples) ]

  perf report -C 1024
  ...

Signed-off-by: Kyle Meyer <kyle.meyer@hpe.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20190620193630.154025-1-meyerk@stormcage.eag.rdlabs.hpecorp.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/perf/perf.h        | 2 +-
 tools/perf/util/header.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/tools/perf/perf.h b/tools/perf/perf.h
index 96f62dd7e3ed..d4ebd0956114 100644
--- a/tools/perf/perf.h
+++ b/tools/perf/perf.h
@@ -25,7 +25,7 @@ static inline unsigned long long rdclock(void)
 }
 
 #ifndef MAX_NR_CPUS
-#define MAX_NR_CPUS			1024
+#define MAX_NR_CPUS			2048
 #endif
 
 extern const char *input_name;
diff --git a/tools/perf/util/header.c b/tools/perf/util/header.c
index f11cead6a151..26437143c940 100644
--- a/tools/perf/util/header.c
+++ b/tools/perf/util/header.c
@@ -1122,7 +1122,7 @@ static int build_caches(struct cpu_cache_level caches[], u32 size, u32 *cntp)
 	return 0;
 }
 
-#define MAX_CACHES 2000
+#define MAX_CACHES (MAX_NR_CPUS * 4)
 
 static int write_cache(struct feat_fd *ff,
 		       struct perf_evlist *evlist __maybe_unused)
-- 
2.20.1

[PATCH AUTOSEL 4.14 079/105] libata: don't request sense data on !ZAC ATA devices

[Sasha Levin]

From: Tejun Heo <tj@kernel.org>

[ Upstream commit ca156e006add67e4beea7896be395160735e09b0 ]

ZAC support added sense data requesting on error for both ZAC and ATA
devices. This seems to cause erratic error handling behaviors on some
SSDs where the device reports sense data availability and then
delivers the wrong content making EH take the wrong actions.  The
failure mode was sporadic on a LITE-ON ssd and couldn't be reliably
reproduced.

There is no value in requesting sense data from non-ZAC ATA devices
while there's a significant risk of introducing EH misbehaviors which
are difficult to reproduce and fix.  Let's do the sense data dancing
only for ZAC devices.

Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Masato Suzuki <masato.suzuki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/ata/libata-eh.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 2651c81d1edf..c398be4b1797 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1535,7 +1535,7 @@ static int ata_eh_read_log_10h(struct ata_device *dev,
 	tf->hob_lbah = buf[10];
 	tf->nsect = buf[12];
 	tf->hob_nsect = buf[13];
-	if (ata_id_has_ncq_autosense(dev->id))
+	if (dev->class == ATA_DEV_ZAC && ata_id_has_ncq_autosense(dev->id))
 		tf->auxiliary = buf[14] << 16 | buf[15] << 8 | buf[16];
 
 	return 0;
@@ -1784,7 +1784,8 @@ void ata_eh_analyze_ncq_error(struct ata_link *link)
 	memcpy(&qc->result_tf, &tf, sizeof(tf));
 	qc->result_tf.flags = ATA_TFLAG_ISADDR | ATA_TFLAG_LBA | ATA_TFLAG_LBA48;
 	qc->err_mask |= AC_ERR_DEV | AC_ERR_NCQ;
-	if ((qc->result_tf.command & ATA_SENSE) || qc->result_tf.auxiliary) {
+	if (dev->class == ATA_DEV_ZAC &&
+	    ((qc->result_tf.command & ATA_SENSE) || qc->result_tf.auxiliary)) {
 		char sense_key, asc, ascq;
 
 		sense_key = (qc->result_tf.auxiliary >> 16) & 0xff;
@@ -1838,10 +1839,11 @@ static unsigned int ata_eh_analyze_tf(struct ata_queued_cmd *qc,
 	}
 
 	switch (qc->dev->class) {
-	case ATA_DEV_ATA:
 	case ATA_DEV_ZAC:
 		if (stat & ATA_SENSE)
 			ata_eh_request_sense(qc, qc->scsicmd);
+		/* fall through */
+	case ATA_DEV_ATA:
 		if (err & ATA_ICRC)
 			qc->err_mask |= AC_ERR_ATA_BUS;
 		if (err & (ATA_UNC | ATA_AMNF))
-- 
2.20.1

[PATCH AUTOSEL 4.14 080/105] clocksource/drivers/exynos_mct: Increase priority over ARM arch timer

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 6282edb72bed5324352522d732080d4c1b9dfed6 ]

Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT
(Multi Core Timer) and standard ARM Architected Timers.

There are use cases, where both timer interfaces are used simultanously.
One of such examples is using Exynos MCT for the main system timer and
ARM Architected Timers for the KVM and virtualized guests (KVM requires
arch timers).

Exynos Multi-Core Timer driver (exynos_mct) must be however started
before ARM Architected Timers (arch_timer), because they both share some
common hardware blocks (global system counter) and turning on MCT is
needed to get ARM Architected Timer working properly.

To ensure selecting Exynos MCT as the main system timer, increase MCT
timer rating. To ensure proper starting order of both timers during
suspend/resume cycle, increase MCT hotplug priority over ARM Archictected
Timers.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clocksource/exynos_mct.c | 4 ++--
 include/linux/cpuhotplug.h       | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/clocksource/exynos_mct.c b/drivers/clocksource/exynos_mct.c
index d55c30f6981d..aaf5bfa9bd9c 100644
--- a/drivers/clocksource/exynos_mct.c
+++ b/drivers/clocksource/exynos_mct.c
@@ -211,7 +211,7 @@ static void exynos4_frc_resume(struct clocksource *cs)
 
 static struct clocksource mct_frc = {
 	.name		= "mct-frc",
-	.rating		= 400,
+	.rating		= 450,	/* use value higher than ARM arch timer */
 	.read		= exynos4_frc_read,
 	.mask		= CLOCKSOURCE_MASK(32),
 	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
@@ -466,7 +466,7 @@ static int exynos4_mct_starting_cpu(unsigned int cpu)
 	evt->set_state_oneshot_stopped = set_state_shutdown;
 	evt->tick_resume = set_state_shutdown;
 	evt->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
-	evt->rating = 450;
+	evt->rating = 500;	/* use value higher than ARM arch timer */
 
 	exynos4_mct_write(TICK_BASE_CNT, mevt->base + MCT_L_TCNTB_OFFSET);
 
diff --git a/include/linux/cpuhotplug.h b/include/linux/cpuhotplug.h
index 6376e2dcb0b7..348ecf5553ba 100644
--- a/include/linux/cpuhotplug.h
+++ b/include/linux/cpuhotplug.h
@@ -115,10 +115,10 @@ enum cpuhp_state {
 	CPUHP_AP_PERF_ARM_ACPI_STARTING,
 	CPUHP_AP_PERF_ARM_STARTING,
 	CPUHP_AP_ARM_L2X0_STARTING,
+	CPUHP_AP_EXYNOS4_MCT_TIMER_STARTING,
 	CPUHP_AP_ARM_ARCH_TIMER_STARTING,
 	CPUHP_AP_ARM_GLOBAL_TIMER_STARTING,
 	CPUHP_AP_JCORE_TIMER_STARTING,
-	CPUHP_AP_EXYNOS4_MCT_TIMER_STARTING,
 	CPUHP_AP_ARM_TWD_STARTING,
 	CPUHP_AP_METAG_TIMER_STARTING,
 	CPUHP_AP_QCOM_TIMER_STARTING,
-- 
2.20.1

[PATCH AUTOSEL 4.14 081/105] rslib: Fix decoding of shortened codes

[Sasha Levin]

From: Ferdinand Blomqvist <ferdinand.blomqvist@gmail.com>

[ Upstream commit 2034a42d1747fc1e1eeef2c6f1789c4d0762cb9c ]

The decoding of shortenend codes is broken. It only works as expected if
there are no erasures.

When decoding with erasures, Lambda (the error and erasure locator
polynomial) is initialized from the given erasure positions. The pad
parameter is not accounted for by the initialisation code, and hence
Lambda is initialized from incorrect erasure positions.

The fix is to adjust the erasure positions by the supplied pad.

Signed-off-by: Ferdinand Blomqvist <ferdinand.blomqvist@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190620141039.9874-3-ferdinand.blomqvist@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 lib/reed_solomon/decode_rs.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/lib/reed_solomon/decode_rs.c b/lib/reed_solomon/decode_rs.c
index 0ec3f257ffdf..8eed0f9ac495 100644
--- a/lib/reed_solomon/decode_rs.c
+++ b/lib/reed_solomon/decode_rs.c
@@ -99,9 +99,9 @@
 	if (no_eras > 0) {
 		/* Init lambda to be the erasure locator polynomial */
 		lambda[1] = alpha_to[rs_modnn(rs,
-					      prim * (nn - 1 - eras_pos[0]))];
+					prim * (nn - 1 - (eras_pos[0] + pad)))];
 		for (i = 1; i < no_eras; i++) {
-			u = rs_modnn(rs, prim * (nn - 1 - eras_pos[i]));
+			u = rs_modnn(rs, prim * (nn - 1 - (eras_pos[i] + pad)));
 			for (j = i + 1; j > 0; j--) {
 				tmp = index_of[lambda[j - 1]];
 				if (tmp != nn) {
-- 
2.20.1

[PATCH AUTOSEL 4.14 082/105] rslib: Fix handling of of caller provided syndrome

[Sasha Levin]

From: Ferdinand Blomqvist <ferdinand.blomqvist@gmail.com>

[ Upstream commit ef4d6a8556b637ad27c8c2a2cff1dda3da38e9a9 ]

Check if the syndrome provided by the caller is zero, and act
accordingly.

Signed-off-by: Ferdinand Blomqvist <ferdinand.blomqvist@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190620141039.9874-6-ferdinand.blomqvist@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 lib/reed_solomon/decode_rs.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/lib/reed_solomon/decode_rs.c b/lib/reed_solomon/decode_rs.c
index 8eed0f9ac495..a5d313381539 100644
--- a/lib/reed_solomon/decode_rs.c
+++ b/lib/reed_solomon/decode_rs.c
@@ -42,8 +42,18 @@
 	BUG_ON(pad < 0 || pad >= nn);
 
 	/* Does the caller provide the syndrome ? */
-	if (s != NULL)
-		goto decode;
+	if (s != NULL) {
+		for (i = 0; i < nroots; i++) {
+			/* The syndrome is in index form,
+			 * so nn represents zero
+			 */
+			if (s[i] != nn)
+				goto decode;
+		}
+
+		/* syndrome is zero, no errors to correct  */
+		return 0;
+	}
 
 	/* form the syndromes; i.e., evaluate data(x) at roots of
 	 * g(x) */
-- 
2.20.1

[PATCH AUTOSEL 4.14 083/105] ixgbe: Check DDM existence in transceiver before access

[Sasha Levin]

From: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>

[ Upstream commit 655c91414579d7bb115a4f7898ee726fc18e0984 ]

Some transceivers may comply with SFF-8472 but not implement the Digital
Diagnostic Monitoring (DDM) interface described in it. The existence of
such area is specified by bit 6 of byte 92, set to 1 if implemented.

Currently, due to not checking this bit ixgbe fails trying to read SFP
module's eeprom with the follow message:

ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error

Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.

This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom
data was confirmed by Mellanox as correct and present in other Passive
DACs in from other manufacturers.

Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c | 3 ++-
 drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h     | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index c3e7a8191128..f7e68083200c 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -3237,7 +3237,8 @@ static int ixgbe_get_module_info(struct net_device *dev,
 		page_swap = true;
 	}
 
-	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap) {
+	if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap ||
+	    !(addr_mode & IXGBE_SFF_DDM_IMPLEMENTED)) {
 		/* We have a SFP, but it does not support SFF-8472 */
 		modinfo->type = ETH_MODULE_SFF_8079;
 		modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
index b0cac961df3b..94df1d99be95 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.h
@@ -70,6 +70,7 @@
 #define IXGBE_SFF_SOFT_RS_SELECT_10G		0x8
 #define IXGBE_SFF_SOFT_RS_SELECT_1G		0x0
 #define IXGBE_SFF_ADDRESSING_MODE		0x4
+#define IXGBE_SFF_DDM_IMPLEMENTED		0x40
 #define IXGBE_SFF_QSFP_DA_ACTIVE_CABLE		0x1
 #define IXGBE_SFF_QSFP_DA_PASSIVE_CABLE		0x8
 #define IXGBE_SFF_QSFP_CONNECTOR_NOT_SEPARABLE	0x23
-- 
2.20.1

[PATCH AUTOSEL 4.14 084/105] crypto: serpent - mark __serpent_setkey_sbox noinline

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 473971187d6727609951858c63bf12b0307ef015 ]

The same bug that gcc hit in the past is apparently now showing
up with clang, which decides to inline __serpent_setkey_sbox:

crypto/serpent_generic.c:268:5: error: stack frame size of 2112 bytes in function '__serpent_setkey' [-Werror,-Wframe-larger-than=]

Marking it 'noinline' reduces the stack usage from 2112 bytes to
192 and 96 bytes, respectively, and seems to generate more
useful object code.

Fixes: c871c10e4ea7 ("crypto: serpent - improve __serpent_setkey with UBSAN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 crypto/serpent_generic.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/crypto/serpent_generic.c b/crypto/serpent_generic.c
index 7c3382facc82..600bd288881d 100644
--- a/crypto/serpent_generic.c
+++ b/crypto/serpent_generic.c
@@ -229,7 +229,13 @@
 	x4 ^= x2;					\
 	})
 
-static void __serpent_setkey_sbox(u32 r0, u32 r1, u32 r2, u32 r3, u32 r4, u32 *k)
+/*
+ * both gcc and clang have misoptimized this function in the past,
+ * producing horrible object code from spilling temporary variables
+ * on the stack. Forcing this part out of line avoids that.
+ */
+static noinline void __serpent_setkey_sbox(u32 r0, u32 r1, u32 r2,
+					   u32 r3, u32 r4, u32 *k)
 {
 	k += 100;
 	S3(r3, r4, r0, r1, r2); store_and_load_keys(r1, r2, r4, r3, 28, 24);
-- 
2.20.1

[PATCH AUTOSEL 4.14 085/105] crypto: asymmetric_keys - select CRYPTO_HASH where needed

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 90acc0653d2bee203174e66d519fbaaa513502de ]

Build testing with some core crypto options disabled revealed
a few modules that are missing CRYPTO_HASH:

crypto/asymmetric_keys/x509_public_key.o: In function `x509_get_sig_params':
x509_public_key.c:(.text+0x4c7): undefined reference to `crypto_alloc_shash'
x509_public_key.c:(.text+0x5e5): undefined reference to `crypto_shash_digest'
crypto/asymmetric_keys/pkcs7_verify.o: In function `pkcs7_digest.isra.0':
pkcs7_verify.c:(.text+0xab): undefined reference to `crypto_alloc_shash'
pkcs7_verify.c:(.text+0x1b2): undefined reference to `crypto_shash_digest'
pkcs7_verify.c:(.text+0x3c1): undefined reference to `crypto_shash_update'
pkcs7_verify.c:(.text+0x411): undefined reference to `crypto_shash_finup'

This normally doesn't show up in randconfig tests because there is
a large number of other options that select CRYPTO_HASH.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 crypto/asymmetric_keys/Kconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/crypto/asymmetric_keys/Kconfig b/crypto/asymmetric_keys/Kconfig
index f3702e533ff4..d8a73d94bb30 100644
--- a/crypto/asymmetric_keys/Kconfig
+++ b/crypto/asymmetric_keys/Kconfig
@@ -15,6 +15,7 @@ config ASYMMETRIC_PUBLIC_KEY_SUBTYPE
 	select MPILIB
 	select CRYPTO_HASH_INFO
 	select CRYPTO_AKCIPHER
+	select CRYPTO_HASH
 	help
 	  This option provides support for asymmetric public key type handling.
 	  If signature generation and/or verification are to be used,
@@ -34,6 +35,7 @@ config X509_CERTIFICATE_PARSER
 config PKCS7_MESSAGE_PARSER
 	tristate "PKCS#7 message parser"
 	depends on X509_CERTIFICATE_PARSER
+	select CRYPTO_HASH
 	select ASN1
 	select OID_REGISTRY
 	help
@@ -56,6 +58,7 @@ config SIGNED_PE_FILE_VERIFICATION
 	bool "Support for PE file signature verification"
 	depends on PKCS7_MESSAGE_PARSER=y
 	depends on SYSTEM_DATA_VERIFICATION
+	select CRYPTO_HASH
 	select ASN1
 	select OID_REGISTRY
 	help
-- 
2.20.1

[PATCH AUTOSEL 4.14 086/105] PCI / ACPI: Use cached ACPI device state to get PCI device power state

[Sasha Levin]

From: Mika Westerberg <mika.westerberg@linux.intel.com>

[ Upstream commit 83a16e3f6d70da99896c7a2639c0b60fff13afb8 ]

The ACPI power state returned by acpi_device_get_power() may depend on
the configuration of ACPI power resources in the system which may change
any time after acpi_device_get_power() has returned, unless the
reference counters of the ACPI power resources in question are set to
prevent that from happening. Thus it is invalid to use acpi_device_get_power()
in acpi_pci_get_power_state() the way it is done now and the value of
the ->power.state field in the corresponding struct acpi_device objects
(which reflects the ACPI power resources reference counting, among other
things) should be used instead.

As an example where this becomes an issue is Intel Ice Lake where the
Thunderbolt controller (NHI), two PCIe root ports (RP0 and RP1) and xHCI
all share the same power resources. The following picture with power
resources marked with [] shows the topology:

  Host bridge
    |
    +- RP0 ---\
    +- RP1 ---|--+--> [TBT]
    +- NHI --/   |
    |            |
    |            v
    +- xHCI --> [D3C]

Here TBT and D3C are the shared ACPI power resources. ACPI _PR3() method
of the devices in question returns either TBT or D3C or both.

Say we runtime suspend first the root ports RP0 and RP1, then NHI. Now
since the TBT power resource is still on when the root ports are runtime
suspended their dev->current_state is set to D3hot. When NHI is runtime
suspended TBT is finally turned off but state of the root ports remain
to be D3hot. Now when the xHCI is runtime suspended D3C gets also turned
off. PCI core thus has power states of these devices cached in their
dev->current_state as follows:

  RP0 -> D3hot
  RP1 -> D3hot
  NHI -> D3cold
  xHCI -> D3cold

If the user now runs lspci for instance, the result is all 1's like in
the below output (00:07.0 is the first root port, RP0):

00:07.0 PCI bridge: Intel Corporation Device 8a1d (rev ff) (prog-if ff)
    !!! Unknown header type 7f
    Kernel driver in use: pcieport

In short the hardware state is not in sync with the software state
anymore. The exact same thing happens with the PME polling thread which
ends up bringing the root ports back into D0 after they are runtime
suspended.

For this reason, modify acpi_pci_get_power_state() so that it uses the
ACPI device power state that was cached by the ACPI core. This makes the
PCI device power state match the ACPI device power state regardless of
state of the shared power resources which may still be on at this point.

Link: https://lore.kernel.org/r/20190618161858.77834-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pci-acpi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
index a3cedf8de863..688e195e85b4 100644
--- a/drivers/pci/pci-acpi.c
+++ b/drivers/pci/pci-acpi.c
@@ -563,7 +563,8 @@ static pci_power_t acpi_pci_get_power_state(struct pci_dev *dev)
 	if (!adev || !acpi_device_power_manageable(adev))
 		return PCI_UNKNOWN;
 
-	if (acpi_device_get_power(adev, &state) || state == ACPI_STATE_UNKNOWN)
+	state = adev->power.state;
+	if (state == ACPI_STATE_UNKNOWN)
 		return PCI_UNKNOWN;
 
 	return state_conv[state];
-- 
2.20.1

Re: [PATCH AUTOSEL 4.14 086/105] PCI / ACPI: Use cached ACPI device state to get PCI device power state

[Rafael J. Wysocki]

On 7/15/2019 4:28 PM, Sasha Levin wrote:
> From: Mika Westerberg <mika.westerberg@linux.intel.com>
>
> [ Upstream commit 83a16e3f6d70da99896c7a2639c0b60fff13afb8 ]
>
> The ACPI power state returned by acpi_device_get_power() may depend on
> the configuration of ACPI power resources in the system which may change
> any time after acpi_device_get_power() has returned, unless the
> reference counters of the ACPI power resources in question are set to
> prevent that from happening. Thus it is invalid to use acpi_device_get_power()
> in acpi_pci_get_power_state() the way it is done now and the value of
> the ->power.state field in the corresponding struct acpi_device objects
> (which reflects the ACPI power resources reference counting, among other
> things) should be used instead.
>
> As an example where this becomes an issue is Intel Ice Lake where the
> Thunderbolt controller (NHI), two PCIe root ports (RP0 and RP1) and xHCI
> all share the same power resources. The following picture with power
> resources marked with [] shows the topology:
>
>    Host bridge
>      |
>      +- RP0 ---\
>      +- RP1 ---|--+--> [TBT]
>      +- NHI --/   |
>      |            |
>      |            v
>      +- xHCI --> [D3C]
>
> Here TBT and D3C are the shared ACPI power resources. ACPI _PR3() method
> of the devices in question returns either TBT or D3C or both.
>
> Say we runtime suspend first the root ports RP0 and RP1, then NHI. Now
> since the TBT power resource is still on when the root ports are runtime
> suspended their dev->current_state is set to D3hot. When NHI is runtime
> suspended TBT is finally turned off but state of the root ports remain
> to be D3hot. Now when the xHCI is runtime suspended D3C gets also turned
> off. PCI core thus has power states of these devices cached in their
> dev->current_state as follows:
>
>    RP0 -> D3hot
>    RP1 -> D3hot
>    NHI -> D3cold
>    xHCI -> D3cold
>
> If the user now runs lspci for instance, the result is all 1's like in
> the below output (00:07.0 is the first root port, RP0):
>
> 00:07.0 PCI bridge: Intel Corporation Device 8a1d (rev ff) (prog-if ff)
>      !!! Unknown header type 7f
>      Kernel driver in use: pcieport
>
> In short the hardware state is not in sync with the software state
> anymore. The exact same thing happens with the PME polling thread which
> ends up bringing the root ports back into D0 after they are runtime
> suspended.
>
> For this reason, modify acpi_pci_get_power_state() so that it uses the
> ACPI device power state that was cached by the ACPI core. This makes the
> PCI device power state match the ACPI device power state regardless of
> state of the shared power resources which may still be on at this point.
>
> Link: https://lore.kernel.org/r/20190618161858.77834-2-mika.westerberg@linux.intel.com
> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> Signed-off-by: Sasha Levin <sashal@kernel.org>
> ---
>   drivers/pci/pci-acpi.c | 3 ++-
>   1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
> index a3cedf8de863..688e195e85b4 100644
> --- a/drivers/pci/pci-acpi.c
> +++ b/drivers/pci/pci-acpi.c
> @@ -563,7 +563,8 @@ static pci_power_t acpi_pci_get_power_state(struct pci_dev *dev)
>   	if (!adev || !acpi_device_power_manageable(adev))
>   		return PCI_UNKNOWN;
>   
> -	if (acpi_device_get_power(adev, &state) || state == ACPI_STATE_UNKNOWN)
> +	state = adev->power.state;
> +	if (state == ACPI_STATE_UNKNOWN)
>   		return PCI_UNKNOWN;
>   
>   	return state_conv[state];

This requires additional changes to really work in all cases, please do 
not include it alone into -stable.

Re: [PATCH AUTOSEL 4.14 086/105] PCI / ACPI: Use cached ACPI device state to get PCI device power state

[Sasha Levin]

On Tue, Jul 16, 2019 at 11:22:44AM +0200, Rafael J. Wysocki wrote:
>On 7/15/2019 4:28 PM, Sasha Levin wrote:
>>From: Mika Westerberg <mika.westerberg@linux.intel.com>
>>
>>[ Upstream commit 83a16e3f6d70da99896c7a2639c0b60fff13afb8 ]
>>
>>The ACPI power state returned by acpi_device_get_power() may depend on
>>the configuration of ACPI power resources in the system which may change
>>any time after acpi_device_get_power() has returned, unless the
>>reference counters of the ACPI power resources in question are set to
>>prevent that from happening. Thus it is invalid to use acpi_device_get_power()
>>in acpi_pci_get_power_state() the way it is done now and the value of
>>the ->power.state field in the corresponding struct acpi_device objects
>>(which reflects the ACPI power resources reference counting, among other
>>things) should be used instead.
>>
>>As an example where this becomes an issue is Intel Ice Lake where the
>>Thunderbolt controller (NHI), two PCIe root ports (RP0 and RP1) and xHCI
>>all share the same power resources. The following picture with power
>>resources marked with [] shows the topology:
>>
>>   Host bridge
>>     |
>>     +- RP0 ---\
>>     +- RP1 ---|--+--> [TBT]
>>     +- NHI --/   |
>>     |            |
>>     |            v
>>     +- xHCI --> [D3C]
>>
>>Here TBT and D3C are the shared ACPI power resources. ACPI _PR3() method
>>of the devices in question returns either TBT or D3C or both.
>>
>>Say we runtime suspend first the root ports RP0 and RP1, then NHI. Now
>>since the TBT power resource is still on when the root ports are runtime
>>suspended their dev->current_state is set to D3hot. When NHI is runtime
>>suspended TBT is finally turned off but state of the root ports remain
>>to be D3hot. Now when the xHCI is runtime suspended D3C gets also turned
>>off. PCI core thus has power states of these devices cached in their
>>dev->current_state as follows:
>>
>>   RP0 -> D3hot
>>   RP1 -> D3hot
>>   NHI -> D3cold
>>   xHCI -> D3cold
>>
>>If the user now runs lspci for instance, the result is all 1's like in
>>the below output (00:07.0 is the first root port, RP0):
>>
>>00:07.0 PCI bridge: Intel Corporation Device 8a1d (rev ff) (prog-if ff)
>>     !!! Unknown header type 7f
>>     Kernel driver in use: pcieport
>>
>>In short the hardware state is not in sync with the software state
>>anymore. The exact same thing happens with the PME polling thread which
>>ends up bringing the root ports back into D0 after they are runtime
>>suspended.
>>
>>For this reason, modify acpi_pci_get_power_state() so that it uses the
>>ACPI device power state that was cached by the ACPI core. This makes the
>>PCI device power state match the ACPI device power state regardless of
>>state of the shared power resources which may still be on at this point.
>>
>>Link: https://lore.kernel.org/r/20190618161858.77834-2-mika.westerberg@linux.intel.com
>>Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
>>Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
>>Signed-off-by: Sasha Levin <sashal@kernel.org>
>>---
>>  drivers/pci/pci-acpi.c | 3 ++-
>>  1 file changed, 2 insertions(+), 1 deletion(-)
>>
>>diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
>>index a3cedf8de863..688e195e85b4 100644
>>--- a/drivers/pci/pci-acpi.c
>>+++ b/drivers/pci/pci-acpi.c
>>@@ -563,7 +563,8 @@ static pci_power_t acpi_pci_get_power_state(struct pci_dev *dev)
>>  	if (!adev || !acpi_device_power_manageable(adev))
>>  		return PCI_UNKNOWN;
>>-	if (acpi_device_get_power(adev, &state) || state == ACPI_STATE_UNKNOWN)
>>+	state = adev->power.state;
>>+	if (state == ACPI_STATE_UNKNOWN)
>>  		return PCI_UNKNOWN;
>>  	return state_conv[state];
>
>This requires additional changes to really work in all cases, please 
>do not include it alone into -stable.

I've dropped it, thanks!

--
Thanks,
Sasha

[PATCH AUTOSEL 4.14 087/105] EDAC: Fix global-out-of-bounds write when setting edac_mc_poll_msec

[Sasha Levin]

From: Eiichi Tsukata <devel@etsukata.com>

[ Upstream commit d8655e7630dafa88bc37f101640e39c736399771 ]

Commit 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2") assumes
edac_mc_poll_msec to be unsigned long, but the type of the variable still
remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds
write.

Reproducer:

  # echo 1001 > /sys/module/edac_core/parameters/edac_mc_poll_msec

KASAN report:

  BUG: KASAN: global-out-of-bounds in edac_set_poll_msec+0x140/0x150
  Write of size 8 at addr ffffffffb91b2d00 by task bash/1996

  CPU: 1 PID: 1996 Comm: bash Not tainted 5.2.0-rc6+ #23
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
  Call Trace:
   dump_stack+0xca/0x13e
   print_address_description.cold+0x5/0x246
   __kasan_report.cold+0x75/0x9a
   ? edac_set_poll_msec+0x140/0x150
   kasan_report+0xe/0x20
   edac_set_poll_msec+0x140/0x150
   ? dimmdev_location_show+0x30/0x30
   ? vfs_lock_file+0xe0/0xe0
   ? _raw_spin_lock+0x87/0xe0
   param_attr_store+0x1b5/0x310
   ? param_array_set+0x4f0/0x4f0
   module_attr_store+0x58/0x80
   ? module_attr_show+0x80/0x80
   sysfs_kf_write+0x13d/0x1a0
   kernfs_fop_write+0x2bc/0x460
   ? sysfs_kf_bin_read+0x270/0x270
   ? kernfs_notify+0x1f0/0x1f0
   __vfs_write+0x81/0x100
   vfs_write+0x1e1/0x560
   ksys_write+0x126/0x250
   ? __ia32_sys_read+0xb0/0xb0
   ? do_syscall_64+0x1f/0x390
   do_syscall_64+0xc1/0x390
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  RIP: 0033:0x7fa7caa5e970
  Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 04
  RSP: 002b:00007fff6acfdfe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
  RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa7caa5e970
  RDX: 0000000000000005 RSI: 0000000000e95c08 RDI: 0000000000000001
  RBP: 0000000000e95c08 R08: 00007fa7cad1e760 R09: 00007fa7cb36a700
  R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000005
  R13: 0000000000000001 R14: 00007fa7cad1d600 R15: 0000000000000005

  The buggy address belongs to the variable:
   edac_mc_poll_msec+0x0/0x40

  Memory state around the buggy address:
   ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
   ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
  >ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
                     ^
   ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
   ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Fix it by changing the type of edac_mc_poll_msec to unsigned int.
The reason why this patch adopts unsigned int rather than unsigned long
is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid
integer conversion bugs and unsigned int will be large enough for
edac_mc_poll_msec.

Reviewed-by: James Morse <james.morse@arm.com>
Fixes: 9da21b1509d8 ("EDAC: Poll timeout cannot be zero, p2")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/edac/edac_mc_sysfs.c | 16 ++++++++--------
 drivers/edac/edac_module.h   |  2 +-
 2 files changed, 9 insertions(+), 9 deletions(-)

diff --git a/drivers/edac/edac_mc_sysfs.c b/drivers/edac/edac_mc_sysfs.c
index 148c4649b155..a4acfa81dfe0 100644
--- a/drivers/edac/edac_mc_sysfs.c
+++ b/drivers/edac/edac_mc_sysfs.c
@@ -26,7 +26,7 @@
 static int edac_mc_log_ue = 1;
 static int edac_mc_log_ce = 1;
 static int edac_mc_panic_on_ue;
-static int edac_mc_poll_msec = 1000;
+static unsigned int edac_mc_poll_msec = 1000;
 
 /* Getter functions for above */
 int edac_mc_get_log_ue(void)
@@ -45,30 +45,30 @@ int edac_mc_get_panic_on_ue(void)
 }
 
 /* this is temporary */
-int edac_mc_get_poll_msec(void)
+unsigned int edac_mc_get_poll_msec(void)
 {
 	return edac_mc_poll_msec;
 }
 
 static int edac_set_poll_msec(const char *val, struct kernel_param *kp)
 {
-	unsigned long l;
+	unsigned int i;
 	int ret;
 
 	if (!val)
 		return -EINVAL;
 
-	ret = kstrtoul(val, 0, &l);
+	ret = kstrtouint(val, 0, &i);
 	if (ret)
 		return ret;
 
-	if (l < 1000)
+	if (i < 1000)
 		return -EINVAL;
 
-	*((unsigned long *)kp->arg) = l;
+	*((unsigned int *)kp->arg) = i;
 
 	/* notify edac_mc engine to reset the poll period */
-	edac_mc_reset_delay_period(l);
+	edac_mc_reset_delay_period(i);
 
 	return 0;
 }
@@ -82,7 +82,7 @@ MODULE_PARM_DESC(edac_mc_log_ue,
 module_param(edac_mc_log_ce, int, 0644);
 MODULE_PARM_DESC(edac_mc_log_ce,
 		 "Log correctable error to console: 0=off 1=on");
-module_param_call(edac_mc_poll_msec, edac_set_poll_msec, param_get_int,
+module_param_call(edac_mc_poll_msec, edac_set_poll_msec, param_get_uint,
 		  &edac_mc_poll_msec, 0644);
 MODULE_PARM_DESC(edac_mc_poll_msec, "Polling period in milliseconds");
 
diff --git a/drivers/edac/edac_module.h b/drivers/edac/edac_module.h
index dec88dcea036..c9f0e73872a6 100644
--- a/drivers/edac/edac_module.h
+++ b/drivers/edac/edac_module.h
@@ -36,7 +36,7 @@ extern int edac_mc_get_log_ue(void);
 extern int edac_mc_get_log_ce(void);
 extern int edac_mc_get_panic_on_ue(void);
 extern int edac_get_poll_msec(void);
-extern int edac_mc_get_poll_msec(void);
+extern unsigned int edac_mc_get_poll_msec(void);
 
 unsigned edac_dimm_info_location(struct dimm_info *dimm, char *buf,
 				 unsigned len);
-- 
2.20.1

[PATCH AUTOSEL 4.14 088/105] bcache: check c->gc_thread by IS_ERR_OR_NULL in cache_set_flush()

[Sasha Levin]

From: Coly Li <colyli@suse.de>

[ Upstream commit b387e9b58679c60f5b1e4313939bd4878204fc37 ]

When system memory is in heavy pressure, bch_gc_thread_start() from
run_cache_set() may fail due to out of memory. In such condition,
c->gc_thread is assigned to -ENOMEM, not NULL pointer. Then in following
failure code path bch_cache_set_error(), when cache_set_flush() gets
called, the code piece to stop c->gc_thread is broken,
         if (!IS_ERR_OR_NULL(c->gc_thread))
                 kthread_stop(c->gc_thread);

And KASAN catches such NULL pointer deference problem, with the warning
information:

[  561.207881] ==================================================================
[  561.207900] BUG: KASAN: null-ptr-deref in kthread_stop+0x3b/0x440
[  561.207904] Write of size 4 at addr 000000000000001c by task kworker/15:1/313

[  561.207913] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G        W         5.0.0-vanilla+ #3
[  561.207916] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019
[  561.207935] Workqueue: events cache_set_flush [bcache]
[  561.207940] Call Trace:
[  561.207948]  dump_stack+0x9a/0xeb
[  561.207955]  ? kthread_stop+0x3b/0x440
[  561.207960]  ? kthread_stop+0x3b/0x440
[  561.207965]  kasan_report+0x176/0x192
[  561.207973]  ? kthread_stop+0x3b/0x440
[  561.207981]  kthread_stop+0x3b/0x440
[  561.207995]  cache_set_flush+0xd4/0x6d0 [bcache]
[  561.208008]  process_one_work+0x856/0x1620
[  561.208015]  ? find_held_lock+0x39/0x1d0
[  561.208028]  ? drain_workqueue+0x380/0x380
[  561.208048]  worker_thread+0x87/0xb80
[  561.208058]  ? __kthread_parkme+0xb6/0x180
[  561.208067]  ? process_one_work+0x1620/0x1620
[  561.208072]  kthread+0x326/0x3e0
[  561.208079]  ? kthread_create_worker_on_cpu+0xc0/0xc0
[  561.208090]  ret_from_fork+0x3a/0x50
[  561.208110] ==================================================================
[  561.208113] Disabling lock debugging due to kernel taint
[  561.208115] irq event stamp: 11800231
[  561.208126] hardirqs last  enabled at (11800231): [<ffffffff83008538>] do_syscall_64+0x18/0x410
[  561.208127] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
[  561.208129] #PF error: [WRITE]
[  561.312253] hardirqs last disabled at (11800230): [<ffffffff830052ff>] trace_hardirqs_off_thunk+0x1a/0x1c
[  561.312259] softirqs last  enabled at (11799832): [<ffffffff850005c7>] __do_softirq+0x5c7/0x8c3
[  561.405975] PGD 0 P4D 0
[  561.442494] softirqs last disabled at (11799821): [<ffffffff831add2c>] irq_exit+0x1ac/0x1e0
[  561.791359] Oops: 0002 [#1] SMP KASAN NOPTI
[  561.791362] CPU: 15 PID: 313 Comm: kworker/15:1 Tainted: G    B   W         5.0.0-vanilla+ #3
[  561.791363] Hardware name: Lenovo ThinkSystem SR650 -[7X05CTO1WW]-/-[7X05CTO1WW]-, BIOS -[IVE136T-2.10]- 03/22/2019
[  561.791371] Workqueue: events cache_set_flush [bcache]
[  561.791374] RIP: 0010:kthread_stop+0x3b/0x440
[  561.791376] Code: 00 00 65 8b 05 26 d5 e0 7c 89 c0 48 0f a3 05 ec aa df 02 0f 82 dc 02 00 00 4c 8d 63 20 be 04 00 00 00 4c 89 e7 e8 65 c5 53 00 <f0> ff 43 20 48 8d 7b 24 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48
[  561.791377] RSP: 0018:ffff88872fc8fd10 EFLAGS: 00010286
[  561.838895] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838916] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838934] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838948] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838966] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838979] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  561.838996] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  563.067028] RAX: 0000000000000000 RBX: fffffffffffffffc RCX: ffffffff832dd314
[  563.067030] RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000297
[  563.067032] RBP: ffff88872fc8fe88 R08: fffffbfff0b8213d R09: fffffbfff0b8213d
[  563.067034] R10: 0000000000000001 R11: fffffbfff0b8213c R12: 000000000000001c
[  563.408618] R13: ffff88dc61cc0f68 R14: ffff888102b94900 R15: ffff88dc61cc0f68
[  563.408620] FS:  0000000000000000(0000) GS:ffff888f7dc00000(0000) knlGS:0000000000000000
[  563.408622] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  563.408623] CR2: 000000000000001c CR3: 0000000f48a1a004 CR4: 00000000007606e0
[  563.408625] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  563.408627] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  563.904795] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  563.915796] PKRU: 55555554
[  563.915797] Call Trace:
[  563.915807]  cache_set_flush+0xd4/0x6d0 [bcache]
[  563.915812]  process_one_work+0x856/0x1620
[  564.001226] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.033563]  ? find_held_lock+0x39/0x1d0
[  564.033567]  ? drain_workqueue+0x380/0x380
[  564.033574]  worker_thread+0x87/0xb80
[  564.062823] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.118042]  ? __kthread_parkme+0xb6/0x180
[  564.118046]  ? process_one_work+0x1620/0x1620
[  564.118048]  kthread+0x326/0x3e0
[  564.118050]  ? kthread_create_worker_on_cpu+0xc0/0xc0
[  564.167066] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.252441]  ret_from_fork+0x3a/0x50
[  564.252447] Modules linked in: msr rpcrdma sunrpc rdma_ucm ib_iser ib_umad rdma_cm ib_ipoib i40iw configfs iw_cm ib_cm libiscsi scsi_transport_iscsi mlx4_ib ib_uverbs mlx4_en ib_core nls_iso8859_1 nls_cp437 vfat fat intel_rapl skx_edac x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel ses raid0 aesni_intel cdc_ether enclosure usbnet ipmi_ssif joydev aes_x86_64 i40e scsi_transport_sas mii bcache md_mod crypto_simd mei_me ioatdma crc64 ptp cryptd pcspkr i2c_i801 mlx4_core glue_helper pps_core mei lpc_ich dca wmi ipmi_si ipmi_devintf nd_pmem dax_pmem nd_btt ipmi_msghandler device_dax pcc_cpufreq button hid_generic usbhid mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect xhci_pci sysimgblt fb_sys_fops xhci_hcd ttm megaraid_sas drm usbcore nfit libnvdimm sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua efivarfs
[  564.299390] bcache: bch_count_io_errors() nvme0n1: IO error on writing btree.
[  564.348360] CR2: 000000000000001c
[  564.348362] ---[ end trace b7f0e5cc7b2103b0 ]---

Therefore, it is not enough to only check whether c->gc_thread is NULL,
we should use IS_ERR_OR_NULL() to check both NULL pointer and error
value.

This patch changes the above buggy code piece in this way,
         if (!IS_ERR_OR_NULL(c->gc_thread))
                 kthread_stop(c->gc_thread);

Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/bcache/super.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/md/bcache/super.c b/drivers/md/bcache/super.c
index 85a5afe01d39..1a270e2262f5 100644
--- a/drivers/md/bcache/super.c
+++ b/drivers/md/bcache/super.c
@@ -1402,7 +1402,7 @@ static void cache_set_flush(struct closure *cl)
 	kobject_put(&c->internal);
 	kobject_del(&c->kobj);
 
-	if (c->gc_thread)
+	if (!IS_ERR_OR_NULL(c->gc_thread))
 		kthread_stop(c->gc_thread);
 
 	if (!IS_ERR_OR_NULL(c->root))
-- 
2.20.1

[PATCH AUTOSEL 4.14 089/105] net: hns3: fix a -Wformat-nonliteral compile warning

[Sasha Levin]

From: Yonglong Liu <liuyonglong@huawei.com>

[ Upstream commit 18d219b783da61a6cc77581f55fc4af2fa16bc36 ]

When setting -Wformat=2, there is a compiler warning like this:

hclge_main.c:xxx:x: warning: format not a string literal and no
format arguments [-Wformat-nonliteral]
strs[i].desc);
^~~~

This patch adds missing format parameter "%s" to snprintf() to
fix it.

Fixes: 46a3df9f9718 ("Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index 654aad6e748b..86523e8993cb 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -619,8 +619,7 @@ static u8 *hclge_comm_get_strings(u32 stringset,
 		return buff;
 
 	for (i = 0; i < size; i++) {
-		snprintf(buff, ETH_GSTRING_LEN,
-			 strs[i].desc);
+		snprintf(buff, ETH_GSTRING_LEN, "%s", strs[i].desc);
 		buff = buff + ETH_GSTRING_LEN;
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 090/105] net: hns3: add some error checking in hclge_tm module

[Sasha Levin]

From: Yunsheng Lin <linyunsheng@huawei.com>

[ Upstream commit 04f25edb48c441fc278ecc154c270f16966cbb90 ]

When hdev->tx_sch_mode is HCLGE_FLAG_VNET_BASE_SCH_MODE, the
hclge_tm_schd_mode_vnet_base_cfg calls hclge_tm_pri_schd_mode_cfg
with vport->vport_id as pri_id, which is used as index for
hdev->tm_info.tc_info, it will cause out of bound access issue
if vport_id is equal to or larger than HNAE3_MAX_TC.

Also hardware only support maximum speed of HCLGE_ETHER_MAX_RATE.

So this patch adds two checks for above cases.

Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c
index 73a75d7cc551..55228b91d80b 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c
@@ -57,7 +57,8 @@ static int hclge_shaper_para_calc(u32 ir, u8 shaper_level,
 	u32 tick;
 
 	/* Calc tick */
-	if (shaper_level >= HCLGE_SHAPER_LVL_CNT)
+	if (shaper_level >= HCLGE_SHAPER_LVL_CNT ||
+	    ir > HCLGE_ETHER_MAX_RATE)
 		return -EINVAL;
 
 	tick = tick_array[shaper_level];
@@ -893,6 +894,9 @@ static int hclge_tm_schd_mode_vnet_base_cfg(struct hclge_vport *vport)
 	int ret;
 	u8 i;
 
+	if (vport->vport_id >= HNAE3_MAX_TC)
+		return -EINVAL;
+
 	ret = hclge_tm_pri_schd_mode_cfg(hdev, vport->vport_id);
 	if (ret)
 		return ret;
-- 
2.20.1

[PATCH AUTOSEL 4.14 091/105] ath10k: destroy sdio workqueue while remove sdio module

[Sasha Levin]

From: Wen Gong <wgong@codeaurora.org>

[ Upstream commit 3ed39f8e747a7aafeec07bb244f2c3a1bdca5730 ]

The workqueue need to flush and destory while remove sdio module,
otherwise it will have thread which is not destory after remove
sdio modules.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/sdio.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index c6440d28ab48..0a1248ebccf5 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -2076,6 +2076,9 @@ static void ath10k_sdio_remove(struct sdio_func *func)
 	cancel_work_sync(&ar_sdio->wr_async_work);
 	ath10k_core_unregister(ar);
 	ath10k_core_destroy(ar);
+
+	flush_workqueue(ar_sdio->workqueue);
+	destroy_workqueue(ar_sdio->workqueue);
 }
 
 static const struct sdio_device_id ath10k_sdio_devices[] = {
-- 
2.20.1

[PATCH AUTOSEL 4.14 092/105] iwlwifi: mvm: Drop large non sta frames

[Sasha Levin]

From: Andrei Otcheretianski <andrei.otcheretianski@intel.com>

[ Upstream commit ac70499ee97231a418dc1a4d6c9dc102e8f64631 ]

In some buggy scenarios we could possible attempt to transmit frames larger
than maximum MSDU size. Since our devices don't know how to handle this,
it may result in asserts, hangs etc.
This can happen, for example, when we receive a large multicast frame
and try to transmit it back to the air in AP mode.
Since in a legal scenario this should never happen, drop such frames and
warn about it.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
index 62a6e293cf12..f0f2be432d20 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
@@ -621,6 +621,9 @@ int iwl_mvm_tx_skb_non_sta(struct iwl_mvm *mvm, struct sk_buff *skb)
 
 	memcpy(&info, skb->cb, sizeof(info));
 
+	if (WARN_ON_ONCE(skb->len > IEEE80211_MAX_DATA_LEN + hdrlen))
+		return -1;
+
 	if (WARN_ON_ONCE(info.flags & IEEE80211_TX_CTL_AMPDU))
 		return -1;
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 093/105] perf stat: Make metric event lookup more robust

[Sasha Levin]

From: Andi Kleen <ak@linux.intel.com>

[ Upstream commit 145c407c808352acd625be793396fd4f33c794f8 ]

After setting up metric groups through the event parser, the metricgroup
code looks them up again in the event list.

Make sure we only look up events that haven't been used by some other
metric. The data structures currently cannot handle more than one metric
per event. This avoids problems with multiple events partially
overlapping.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Link: http://lkml.kernel.org/r/20190624193711.35241-2-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/perf/util/stat-shadow.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/tools/perf/util/stat-shadow.c b/tools/perf/util/stat-shadow.c
index 37363869c9a1..eadc9a2aef16 100644
--- a/tools/perf/util/stat-shadow.c
+++ b/tools/perf/util/stat-shadow.c
@@ -271,7 +271,7 @@ static struct perf_evsel *perf_stat__find_event(struct perf_evlist *evsel_list,
 	struct perf_evsel *c2;
 
 	evlist__for_each_entry (evsel_list, c2) {
-		if (!strcasecmp(c2->name, name))
+		if (!strcasecmp(c2->name, name) && !c2->collect_stat)
 			return c2;
 	}
 	return NULL;
@@ -310,7 +310,8 @@ void perf_stat__collect_metric_expr(struct perf_evlist *evsel_list)
 			if (leader) {
 				/* Search in group */
 				for_each_group_member (oc, leader) {
-					if (!strcasecmp(oc->name, metric_names[i])) {
+					if (!strcasecmp(oc->name, metric_names[i]) &&
+						!oc->collect_stat) {
 						found = true;
 						break;
 					}
-- 
2.20.1

[PATCH AUTOSEL 4.14 094/105] net: usb: asix: init MAC address buffers

[Sasha Levin]

From: Phong Tran <tranmanphong@gmail.com>

[ Upstream commit 78226f6eaac80bf30256a33a4926c194ceefdf36 ]

This is for fixing bug KMSAN: uninit-value in ax88772_bind

Tested by
https://groups.google.com/d/msg/syzkaller-bugs/aFQurGotng4/eB_HlNhhCwAJ

Reported-by: syzbot+8a3fc6674bbc3978ed4e@syzkaller.appspotmail.com

syzbot found the following crash on:

HEAD commit:    f75e4cfe kmsan: use kmsan_handle_urb() in urb.c
git tree:       kmsan
console output: https://syzkaller.appspot.com/x/log.txt?x=136d720ea00000
kernel config:
https://syzkaller.appspot.com/x/.config?x=602468164ccdc30a
dashboard link:
https://syzkaller.appspot.com/bug?extid=8a3fc6674bbc3978ed4e
compiler:       clang version 9.0.0 (/home/glider/llvm/clang
06d00afa61eef8f7f501ebdb4e8612ea43ec2d78)
syz repro:
https://syzkaller.appspot.com/x/repro.syz?x=12788316a00000
C reproducer:   https://syzkaller.appspot.com/x/repro.c?x=120359aaa00000

==================================================================
BUG: KMSAN: uninit-value in is_valid_ether_addr
include/linux/etherdevice.h:200 [inline]
BUG: KMSAN: uninit-value in asix_set_netdev_dev_addr
drivers/net/usb/asix_devices.c:73 [inline]
BUG: KMSAN: uninit-value in ax88772_bind+0x93d/0x11e0
drivers/net/usb/asix_devices.c:724
CPU: 0 PID: 3348 Comm: kworker/0:2 Not tainted 5.1.0+ #1
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0x191/0x1f0 lib/dump_stack.c:113
  kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622
  __msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310
  is_valid_ether_addr include/linux/etherdevice.h:200 [inline]
  asix_set_netdev_dev_addr drivers/net/usb/asix_devices.c:73 [inline]
  ax88772_bind+0x93d/0x11e0 drivers/net/usb/asix_devices.c:724
  usbnet_probe+0x10f5/0x3940 drivers/net/usb/usbnet.c:1728
  usb_probe_interface+0xd66/0x1320 drivers/usb/core/driver.c:361
  really_probe+0xdae/0x1d80 drivers/base/dd.c:513
  driver_probe_device+0x1b3/0x4f0 drivers/base/dd.c:671
  __device_attach_driver+0x5b8/0x790 drivers/base/dd.c:778
  bus_for_each_drv+0x28e/0x3b0 drivers/base/bus.c:454
  __device_attach+0x454/0x730 drivers/base/dd.c:844
  device_initial_probe+0x4a/0x60 drivers/base/dd.c:891
  bus_probe_device+0x137/0x390 drivers/base/bus.c:514
  device_add+0x288d/0x30e0 drivers/base/core.c:2106
  usb_set_configuration+0x30dc/0x3750 drivers/usb/core/message.c:2027
  generic_probe+0xe7/0x280 drivers/usb/core/generic.c:210
  usb_probe_device+0x14c/0x200 drivers/usb/core/driver.c:266
  really_probe+0xdae/0x1d80 drivers/base/dd.c:513
  driver_probe_device+0x1b3/0x4f0 drivers/base/dd.c:671
  __device_attach_driver+0x5b8/0x790 drivers/base/dd.c:778
  bus_for_each_drv+0x28e/0x3b0 drivers/base/bus.c:454
  __device_attach+0x454/0x730 drivers/base/dd.c:844
  device_initial_probe+0x4a/0x60 drivers/base/dd.c:891
  bus_probe_device+0x137/0x390 drivers/base/bus.c:514
  device_add+0x288d/0x30e0 drivers/base/core.c:2106
  usb_new_device+0x23e5/0x2ff0 drivers/usb/core/hub.c:2534
  hub_port_connect drivers/usb/core/hub.c:5089 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
  port_event drivers/usb/core/hub.c:5350 [inline]
  hub_event+0x48d1/0x7290 drivers/usb/core/hub.c:5432
  process_one_work+0x1572/0x1f00 kernel/workqueue.c:2269
  process_scheduled_works kernel/workqueue.c:2331 [inline]
  worker_thread+0x189c/0x2460 kernel/workqueue.c:2417
  kthread+0x4b5/0x4f0 kernel/kthread.c:254
  ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:355

Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/asix_devices.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index d0c0ac0c3519..9b751d4bd327 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -238,7 +238,7 @@ static void asix_phy_reset(struct usbnet *dev, unsigned int reset_bits)
 static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	int ret = 0;
-	u8 buf[ETH_ALEN];
+	u8 buf[ETH_ALEN] = {0};
 	int i;
 	unsigned long gpio_bits = dev->driver_info->data;
 
@@ -689,7 +689,7 @@ static int asix_resume(struct usb_interface *intf)
 static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	int ret, i;
-	u8 buf[ETH_ALEN], chipcode = 0;
+	u8 buf[ETH_ALEN] = {0}, chipcode = 0;
 	u32 phyid;
 	struct asix_common_private *priv;
 
@@ -1065,7 +1065,7 @@ static const struct net_device_ops ax88178_netdev_ops = {
 static int ax88178_bind(struct usbnet *dev, struct usb_interface *intf)
 {
 	int ret;
-	u8 buf[ETH_ALEN];
+	u8 buf[ETH_ALEN] = {0};
 
 	usbnet_get_endpoints(dev,intf);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 095/105] gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 3285170f28a850638794cdfe712eb6d93e51e706 ]

Commit 372e722ea4dd4ca1 ("gpiolib: use descriptors internally") renamed
the functions to use a "gpiod" prefix, and commit 79a9becda8940deb
("gpiolib: export descriptor-based GPIO interface") introduced the "raw"
variants, but both changes forgot to update the comments.

Readd a similar reference to gpiod_set_value(), which was accidentally
removed by commit 1e77fc82110ac36f ("gpio: Add missing open drain/source
handling to gpiod_set_value_cansleep()").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190701142738.25219-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpio/gpiolib.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 21062cb6b85f..3db0a9b0d259 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -2480,7 +2480,7 @@ static int _gpiod_get_raw_value(const struct gpio_desc *desc)
 int gpiod_get_raw_value(const struct gpio_desc *desc)
 {
 	VALIDATE_DESC(desc);
-	/* Should be using gpio_get_value_cansleep() */
+	/* Should be using gpiod_get_raw_value_cansleep() */
 	WARN_ON(desc->gdev->chip->can_sleep);
 	return _gpiod_get_raw_value(desc);
 }
@@ -2501,7 +2501,7 @@ int gpiod_get_value(const struct gpio_desc *desc)
 	int value;
 
 	VALIDATE_DESC(desc);
-	/* Should be using gpio_get_value_cansleep() */
+	/* Should be using gpiod_get_value_cansleep() */
 	WARN_ON(desc->gdev->chip->can_sleep);
 
 	value = _gpiod_get_raw_value(desc);
@@ -2670,7 +2670,7 @@ void gpiod_set_array_value_complex(bool raw, bool can_sleep,
 void gpiod_set_raw_value(struct gpio_desc *desc, int value)
 {
 	VALIDATE_DESC_VOID(desc);
-	/* Should be using gpiod_set_value_cansleep() */
+	/* Should be using gpiod_set_raw_value_cansleep() */
 	WARN_ON(desc->gdev->chip->can_sleep);
 	_gpiod_set_raw_value(desc, value);
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 096/105] Bluetooth: hci_bcsp: Fix memory leak in rx_skb

[Sasha Levin]

From: Tomas Bortoli <tomasbortoli@gmail.com>

[ Upstream commit 4ce9146e0370fcd573f0372d9b4e5a211112567c ]

Syzkaller found that it is possible to provoke a memory leak by
never freeing rx_skb in struct bcsp_struct.

Fix by freeing in bcsp_close()

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+98162c885993b72f19c4@syzkaller.appspotmail.com
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/bluetooth/hci_bcsp.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/bluetooth/hci_bcsp.c b/drivers/bluetooth/hci_bcsp.c
index d880f4e33c75..57a7f4255ac0 100644
--- a/drivers/bluetooth/hci_bcsp.c
+++ b/drivers/bluetooth/hci_bcsp.c
@@ -757,6 +757,11 @@ static int bcsp_close(struct hci_uart *hu)
 	skb_queue_purge(&bcsp->rel);
 	skb_queue_purge(&bcsp->unrel);
 
+	if (bcsp->rx_skb) {
+		kfree_skb(bcsp->rx_skb);
+		bcsp->rx_skb = NULL;
+	}
+
 	kfree(bcsp);
 	return 0;
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 097/105] Bluetooth: 6lowpan: search for destination address in all peers

[Sasha Levin]

From: Josua Mayer <josua.mayer@jm0.eu>

[ Upstream commit b188b03270b7f8568fc714101ce82fbf5e811c5a ]

Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.

For one peer, no checks are performed to see if it is meant to receive
packets for a given address.

As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.

Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/6lowpan.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/net/bluetooth/6lowpan.c b/net/bluetooth/6lowpan.c
index 4e2576fc0c59..357475cceec6 100644
--- a/net/bluetooth/6lowpan.c
+++ b/net/bluetooth/6lowpan.c
@@ -187,10 +187,16 @@ static inline struct lowpan_peer *peer_lookup_dst(struct lowpan_btle_dev *dev,
 	}
 
 	if (!rt) {
-		nexthop = &lowpan_cb(skb)->gw;
-
-		if (ipv6_addr_any(nexthop))
-			return NULL;
+		if (ipv6_addr_any(&lowpan_cb(skb)->gw)) {
+			/* There is neither route nor gateway,
+			 * probably the destination is a direct peer.
+			 */
+			nexthop = daddr;
+		} else {
+			/* There is a known gateway
+			 */
+			nexthop = &lowpan_cb(skb)->gw;
+		}
 	} else {
 		nexthop = rt6_nexthop(rt, daddr);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 098/105] Bluetooth: Check state in l2cap_disconnect_rsp

[Sasha Levin]

From: Matias Karhumaa <matias.karhumaa@gmail.com>

[ Upstream commit 28261da8a26f4915aa257d12d506c6ba179d961f ]

Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.

Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.

Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8                #394 [hci1] 10.748949
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8                #395 [hci1] 10.749062
      Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #396 [hci1] 10.749073
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5    #397 [hci1] 10.752391
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5    #398 [hci1] 10.753394
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #399 [hci1] 10.756499
      L2CAP: Disconnection Request (0x06) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #400 [hci1] 10.756548
      L2CAP: Disconnection Response (0x07) ident 26 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12               #401 [hci1] 10.757459
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #402 [hci1] 10.759148
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o..   10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5    #403 [hci1] 10.759386
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12               #404 [hci1] 10.760397
      L2CAP: Connection Request (0x02) ident 27 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16               #405 [hci1] 10.760441
      L2CAP: Connection Response (0x03) ident 27 len 8
        Destination CID: 65
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27               #406 [hci1] 10.760449
      L2CAP: Configure Request (0x04) ident 19 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5    #407 [hci1] 10.761399
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16               #408 [hci1] 10.762942
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8            #22702 [hci0] 1664.411056
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Disconnect (DISC) (0x43)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x53 poll/final 1
         Length: 0
         FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8            #22703 [hci0] 1664.411136
      Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
      RFCOMM: Unnumbered Ack (UA) (0x63)
         Address: 0x03 cr 1 dlci 0x00
         Control: 0x73 poll/final 1
         Length: 0
         FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22704 [hci0] 1664.411143
      L2CAP: Disconnection Request (0x06) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22705 [hci0] 1664.414009
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22706 [hci0] 1664.415007
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22707 [hci0] 1664.418674
      L2CAP: Disconnection Request (0x06) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22708 [hci0] 1664.418762
      L2CAP: Disconnection Response (0x07) ident 17 len 4
        Destination CID: 65
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12           #22709 [hci0] 1664.421073
      L2CAP: Connection Request (0x02) ident 12 len 4
        PSM: 1 (0x0001)
        Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22710 [hci0] 1664.421371
      L2CAP: Disconnection Response (0x07) ident 11 len 4
        Destination CID: 65
        Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22711 [hci0] 1664.424082
        Num handles: 1
        Handle: 43
        Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5  #22712 [hci0] 1664.425040
        Num handles: 1
        Handle: 43
        Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12           #22713 [hci0] 1664.426103
      L2CAP: Connection Request (0x02) ident 18 len 4
        PSM: 3 (0x0003)
        Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16           #22714 [hci0] 1664.426186
      L2CAP: Connection Response (0x03) ident 18 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27           #22715 [hci0] 1664.426196
      L2CAP: Configure Request (0x04) ident 13 len 19
        Destination CID: 65
        Flags: 0x0000
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 1013
        Option: Retransmission and Flow Control (0x04) [mandatory]
          Mode: Basic (0x00)
          TX window size: 0
          Max transmit: 0
          Retransmission timeout: 0
          Monitor timeout: 0
          Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16           #22716 [hci0] 1664.428804
      L2CAP: Connection Response (0x03) ident 12 len 8
        Destination CID: 66
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
*snip*

Fix is to check that channel is in state BT_DISCONN before deleting the
channel.

This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.

Reported-by: Matti Kamunen <matti.kamunen@synopsys.com>
Reported-by: Ari Timonen <ari.timonen@synopsys.com>
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/l2cap_core.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index 0ee64f67300a..0c2219f483d7 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -4384,6 +4384,12 @@ static inline int l2cap_disconnect_rsp(struct l2cap_conn *conn,
 
 	l2cap_chan_lock(chan);
 
+	if (chan->state != BT_DISCONN) {
+		l2cap_chan_unlock(chan);
+		mutex_unlock(&conn->chan_lock);
+		return 0;
+	}
+
 	l2cap_chan_hold(chan);
 	l2cap_chan_del(chan, 0);
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 099/105] gtp: add missing gtp_encap_disable_sock() in gtp_encap_enable()

[Sasha Levin]

From: Taehee Yoo <ap420073@gmail.com>

[ Upstream commit e30155fd23c9c141cbe7d99b786e10a83a328837 ]

If an invalid role is sent from user space, gtp_encap_enable() will fail.
Then, it should call gtp_encap_disable_sock() but current code doesn't.
It makes memory leak.

Fixes: 91ed81f9abc7 ("gtp: support SGSN-side tunnels")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/gtp.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index f38e32a7ec9c..dba3869b61be 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -845,8 +845,13 @@ static int gtp_encap_enable(struct gtp_dev *gtp, struct nlattr *data[])
 
 	if (data[IFLA_GTP_ROLE]) {
 		role = nla_get_u32(data[IFLA_GTP_ROLE]);
-		if (role > GTP_ROLE_SGSN)
+		if (role > GTP_ROLE_SGSN) {
+			if (sk0)
+				gtp_encap_disable_sock(sk0);
+			if (sk1u)
+				gtp_encap_disable_sock(sk1u);
 			return -EINVAL;
+		}
 	}
 
 	gtp->sk0 = sk0;
-- 
2.20.1

[PATCH AUTOSEL 4.14 100/105] Bluetooth: validate BLE connection interval updates

[Sasha Levin]

From: csonsino <csonsino@gmail.com>

[ Upstream commit c49a8682fc5d298d44e8d911f4fa14690ea9485e ]

Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.

The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.

The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.

The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.

Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/bluetooth/hci_event.c  | 5 +++++
 net/bluetooth/l2cap_core.c | 9 ++++++++-
 2 files changed, 13 insertions(+), 1 deletion(-)

diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index 363dc85bbc5c..3d2f64a6d623 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -5089,6 +5089,11 @@ static void hci_le_remote_conn_param_req_evt(struct hci_dev *hdev,
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_UNKNOWN_CONN_ID);
 
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval)
+		return send_conn_param_neg_reply(hdev, handle,
+						 HCI_ERROR_INVALID_LL_PARAMS);
+
 	if (hci_check_conn_params(min, max, latency, timeout))
 		return send_conn_param_neg_reply(hdev, handle,
 						 HCI_ERROR_INVALID_LL_PARAMS);
diff --git a/net/bluetooth/l2cap_core.c b/net/bluetooth/l2cap_core.c
index 0c2219f483d7..4dc1db85a9c2 100644
--- a/net/bluetooth/l2cap_core.c
+++ b/net/bluetooth/l2cap_core.c
@@ -5287,7 +5287,14 @@ static inline int l2cap_conn_param_update_req(struct l2cap_conn *conn,
 
 	memset(&rsp, 0, sizeof(rsp));
 
-	err = hci_check_conn_params(min, max, latency, to_multiplier);
+	if (min < hcon->le_conn_min_interval ||
+	    max > hcon->le_conn_max_interval) {
+		BT_DBG("requested connection interval exceeds current bounds.");
+		err = -EINVAL;
+	} else {
+		err = hci_check_conn_params(min, max, latency, to_multiplier);
+	}
+
 	if (err)
 		rsp.result = cpu_to_le16(L2CAP_CONN_PARAM_REJECTED);
 	else
-- 
2.20.1

[PATCH AUTOSEL 4.14 101/105] gtp: fix suspicious RCU usage

[Sasha Levin]

From: Taehee Yoo <ap420073@gmail.com>

[ Upstream commit e198987e7dd7d3645a53875151cd6f8fc425b706 ]

gtp_encap_enable_socket() and gtp_encap_destroy() are not protected
by rcu_read_lock(). and it's not safe to write sk->sk_user_data.
This patch make these functions to use lock_sock() instead of
rcu_dereference_sk_user_data().

Test commands:
    gtp-link add gtp1

Splat looks like:
[   83.238315] =============================
[   83.239127] WARNING: suspicious RCU usage
[   83.239702] 5.2.0-rc6+ #49 Not tainted
[   83.240268] -----------------------------
[   83.241205] drivers/net/gtp.c:799 suspicious rcu_dereference_check() usage!
[   83.243828]
[   83.243828] other info that might help us debug this:
[   83.243828]
[   83.246325]
[   83.246325] rcu_scheduler_active = 2, debug_locks = 1
[   83.247314] 1 lock held by gtp-link/1008:
[   83.248523]  #0: 0000000017772c7f (rtnl_mutex){+.+.}, at: __rtnl_newlink+0x5f5/0x11b0
[   83.251503]
[   83.251503] stack backtrace:
[   83.252173] CPU: 0 PID: 1008 Comm: gtp-link Not tainted 5.2.0-rc6+ #49
[   83.253271] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[   83.254562] Call Trace:
[   83.254995]  dump_stack+0x7c/0xbb
[   83.255567]  gtp_encap_enable_socket+0x2df/0x360 [gtp]
[   83.256415]  ? gtp_find_dev+0x1a0/0x1a0 [gtp]
[   83.257161]  ? memset+0x1f/0x40
[   83.257843]  gtp_newlink+0x90/0xa21 [gtp]
[   83.258497]  ? __netlink_ns_capable+0xc3/0xf0
[   83.259260]  __rtnl_newlink+0xb9f/0x11b0
[   83.260022]  ? rtnl_link_unregister+0x230/0x230
[ ... ]

Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/gtp.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index dba3869b61be..2756edd84abc 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -293,12 +293,14 @@ static void gtp_encap_destroy(struct sock *sk)
 {
 	struct gtp_dev *gtp;
 
-	gtp = rcu_dereference_sk_user_data(sk);
+	lock_sock(sk);
+	gtp = sk->sk_user_data;
 	if (gtp) {
 		udp_sk(sk)->encap_type = 0;
 		rcu_assign_sk_user_data(sk, NULL);
 		sock_put(sk);
 	}
+	release_sock(sk);
 }
 
 static void gtp_encap_disable_sock(struct sock *sk)
@@ -798,7 +800,8 @@ static struct sock *gtp_encap_enable_socket(int fd, int type,
 		goto out_sock;
 	}
 
-	if (rcu_dereference_sk_user_data(sock->sk)) {
+	lock_sock(sock->sk);
+	if (sock->sk->sk_user_data) {
 		sk = ERR_PTR(-EBUSY);
 		goto out_sock;
 	}
@@ -814,6 +817,7 @@ static struct sock *gtp_encap_enable_socket(int fd, int type,
 	setup_udp_tunnel_sock(sock_net(sock->sk), sock, &tuncfg);
 
 out_sock:
+	release_sock(sock->sk);
 	sockfd_put(sock);
 	return sk;
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 102/105] gtp: fix Illegal context switch in RCU read-side critical section.

[Sasha Levin]

From: Taehee Yoo <ap420073@gmail.com>

[ Upstream commit 3f167e1921865b379a9becf03828e7202c7b4917 ]

ipv4_pdp_add() is called in RCU read-side critical section.
So GFP_KERNEL should not be used in the function.
This patch make ipv4_pdp_add() to use GFP_ATOMIC instead of GFP_KERNEL.

Test commands:
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 100 200 1.1.1.1 2.2.2.2

Splat looks like:
[  130.618881] =============================
[  130.626382] WARNING: suspicious RCU usage
[  130.626994] 5.2.0-rc6+ #50 Not tainted
[  130.627622] -----------------------------
[  130.628223] ./include/linux/rcupdate.h:266 Illegal context switch in RCU read-side critical section!
[  130.629684]
[  130.629684] other info that might help us debug this:
[  130.629684]
[  130.631022]
[  130.631022] rcu_scheduler_active = 2, debug_locks = 1
[  130.632136] 4 locks held by gtp-tunnel/1025:
[  130.632925]  #0: 000000002b93c8b7 (cb_lock){++++}, at: genl_rcv+0x15/0x40
[  130.634159]  #1: 00000000f17bc999 (genl_mutex){+.+.}, at: genl_rcv_msg+0xfb/0x130
[  130.635487]  #2: 00000000c644ed8e (rtnl_mutex){+.+.}, at: gtp_genl_new_pdp+0x18c/0x1150 [gtp]
[  130.636936]  #3: 0000000007a1cde7 (rcu_read_lock){....}, at: gtp_genl_new_pdp+0x187/0x1150 [gtp]
[  130.638348]
[  130.638348] stack backtrace:
[  130.639062] CPU: 1 PID: 1025 Comm: gtp-tunnel Not tainted 5.2.0-rc6+ #50
[  130.641318] Call Trace:
[  130.641707]  dump_stack+0x7c/0xbb
[  130.642252]  ___might_sleep+0x2c0/0x3b0
[  130.642862]  kmem_cache_alloc_trace+0x1cd/0x2b0
[  130.643591]  gtp_genl_new_pdp+0x6c5/0x1150 [gtp]
[  130.644371]  genl_family_rcv_msg+0x63a/0x1030
[  130.645074]  ? mutex_lock_io_nested+0x1090/0x1090
[  130.645845]  ? genl_unregister_family+0x630/0x630
[  130.646592]  ? debug_show_all_locks+0x2d0/0x2d0
[  130.647293]  ? check_flags.part.40+0x440/0x440
[  130.648099]  genl_rcv_msg+0xa3/0x130
[ ... ]

Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/gtp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index 2756edd84abc..c751f87c935e 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -956,7 +956,7 @@ static int ipv4_pdp_add(struct gtp_dev *gtp, struct sock *sk,
 
 	}
 
-	pctx = kmalloc(sizeof(struct pdp_ctx), GFP_KERNEL);
+	pctx = kmalloc(sizeof(*pctx), GFP_ATOMIC);
 	if (pctx == NULL)
 		return -ENOMEM;
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 103/105] gtp: fix use-after-free in gtp_encap_destroy()

[Sasha Levin]

From: Taehee Yoo <ap420073@gmail.com>

[ Upstream commit 1788b8569f5de27da09087fa3f6580d2aa04cc75 ]

gtp_encap_destroy() is called twice.
1. When interface is deleted.
2. When udp socket is destroyed.
either gtp->sk0 or gtp->sk1u could be freed by sock_put() in
gtp_encap_destroy(). so, when gtp_encap_destroy() is called again,
it would uses freed sk pointer.

patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to
null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected
by rtnl_lock. so, rtnl_lock() is added.

Test command:
   gtp-link add gtp1 &
   killall gtp-link
   ip link del gtp1

Splat looks like:
[   83.182767] BUG: KASAN: use-after-free in __lock_acquire+0x3a20/0x46a0
[   83.184128] Read of size 8 at addr ffff8880cc7d5360 by task ip/1008
[   83.185567] CPU: 1 PID: 1008 Comm: ip Not tainted 5.2.0-rc6+ #50
[   83.188469] Call Trace:
[ ... ]
[   83.200126]  lock_acquire+0x141/0x380
[   83.200575]  ? lock_sock_nested+0x3a/0xf0
[   83.201069]  _raw_spin_lock_bh+0x38/0x70
[   83.201551]  ? lock_sock_nested+0x3a/0xf0
[   83.202044]  lock_sock_nested+0x3a/0xf0
[   83.202520]  gtp_encap_destroy+0x18/0xe0 [gtp]
[   83.203065]  gtp_encap_disable.isra.14+0x13/0x50 [gtp]
[   83.203687]  gtp_dellink+0x56/0x170 [gtp]
[   83.204190]  rtnl_delete_link+0xb4/0x100
[ ... ]
[   83.236513] Allocated by task 976:
[   83.236925]  save_stack+0x19/0x80
[   83.237332]  __kasan_kmalloc.constprop.3+0xa0/0xd0
[   83.237894]  kmem_cache_alloc+0xd8/0x280
[   83.238360]  sk_prot_alloc.isra.42+0x50/0x200
[   83.238874]  sk_alloc+0x32/0x940
[   83.239264]  inet_create+0x283/0xc20
[   83.239684]  __sock_create+0x2dd/0x540
[   83.240136]  __sys_socket+0xca/0x1a0
[   83.240550]  __x64_sys_socket+0x6f/0xb0
[   83.240998]  do_syscall_64+0x9c/0x450
[   83.241466]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[   83.242061]
[   83.242249] Freed by task 0:
[   83.242616]  save_stack+0x19/0x80
[   83.243013]  __kasan_slab_free+0x111/0x150
[   83.243498]  kmem_cache_free+0x89/0x250
[   83.244444]  __sk_destruct+0x38f/0x5a0
[   83.245366]  rcu_core+0x7e9/0x1c20
[   83.245766]  __do_softirq+0x213/0x8fa

Fixes: 1e3a3abd8b28 ("gtp: make GTP sockets in gtp_newlink optional")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/gtp.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index c751f87c935e..53fd66534e3a 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -289,13 +289,17 @@ static int gtp1u_udp_encap_recv(struct gtp_dev *gtp, struct sk_buff *skb)
 	return gtp_rx(pctx, skb, hdrlen, gtp->role);
 }
 
-static void gtp_encap_destroy(struct sock *sk)
+static void __gtp_encap_destroy(struct sock *sk)
 {
 	struct gtp_dev *gtp;
 
 	lock_sock(sk);
 	gtp = sk->sk_user_data;
 	if (gtp) {
+		if (gtp->sk0 == sk)
+			gtp->sk0 = NULL;
+		else
+			gtp->sk1u = NULL;
 		udp_sk(sk)->encap_type = 0;
 		rcu_assign_sk_user_data(sk, NULL);
 		sock_put(sk);
@@ -303,12 +307,19 @@ static void gtp_encap_destroy(struct sock *sk)
 	release_sock(sk);
 }
 
+static void gtp_encap_destroy(struct sock *sk)
+{
+	rtnl_lock();
+	__gtp_encap_destroy(sk);
+	rtnl_unlock();
+}
+
 static void gtp_encap_disable_sock(struct sock *sk)
 {
 	if (!sk)
 		return;
 
-	gtp_encap_destroy(sk);
+	__gtp_encap_destroy(sk);
 }
 
 static void gtp_encap_disable(struct gtp_dev *gtp)
@@ -1045,6 +1056,7 @@ static int gtp_genl_new_pdp(struct sk_buff *skb, struct genl_info *info)
 		return -EINVAL;
 	}
 
+	rtnl_lock();
 	rcu_read_lock();
 
 	gtp = gtp_find_dev(sock_net(skb->sk), info->attrs);
@@ -1069,6 +1081,7 @@ static int gtp_genl_new_pdp(struct sk_buff *skb, struct genl_info *info)
 
 out_unlock:
 	rcu_read_unlock();
+	rtnl_unlock();
 	return err;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.14 104/105] gtp: fix use-after-free in gtp_newlink()

[Sasha Levin]

From: Taehee Yoo <ap420073@gmail.com>

[ Upstream commit a2bed90704c68d3763bf24decb1b781a45395de8 ]

Current gtp_newlink() could be called after unregister_pernet_subsys().
gtp_newlink() uses gtp_net but it can be destroyed by
unregister_pernet_subsys().
So unregister_pernet_subsys() should be called after
rtnl_link_unregister().

Test commands:
   #SHELL 1
   while :
   do
	   for i in {1..5}
	   do
		./gtp-link add gtp$i &
	   done
	   killall gtp-link
   done

   #SHELL 2
   while :
   do
	modprobe -rv gtp
   done

Splat looks like:
[  753.176631] BUG: KASAN: use-after-free in gtp_newlink+0x9b4/0xa5c [gtp]
[  753.177722] Read of size 8 at addr ffff8880d48f2458 by task gtp-link/7126
[  753.179082] CPU: 0 PID: 7126 Comm: gtp-link Tainted: G        W         5.2.0-rc6+ #50
[  753.185801] Call Trace:
[  753.186264]  dump_stack+0x7c/0xbb
[  753.186863]  ? gtp_newlink+0x9b4/0xa5c [gtp]
[  753.187583]  print_address_description+0xc7/0x240
[  753.188382]  ? gtp_newlink+0x9b4/0xa5c [gtp]
[  753.189097]  ? gtp_newlink+0x9b4/0xa5c [gtp]
[  753.189846]  __kasan_report+0x12a/0x16f
[  753.190542]  ? gtp_newlink+0x9b4/0xa5c [gtp]
[  753.191298]  kasan_report+0xe/0x20
[  753.191893]  gtp_newlink+0x9b4/0xa5c [gtp]
[  753.192580]  ? __netlink_ns_capable+0xc3/0xf0
[  753.193370]  __rtnl_newlink+0xb9f/0x11b0
[ ... ]
[  753.241201] Allocated by task 7186:
[  753.241844]  save_stack+0x19/0x80
[  753.242399]  __kasan_kmalloc.constprop.3+0xa0/0xd0
[  753.243192]  __kmalloc+0x13e/0x300
[  753.243764]  ops_init+0xd6/0x350
[  753.244314]  register_pernet_operations+0x249/0x6f0
[ ... ]
[  753.251770] Freed by task 7178:
[  753.252288]  save_stack+0x19/0x80
[  753.252833]  __kasan_slab_free+0x111/0x150
[  753.253962]  kfree+0xc7/0x280
[  753.254509]  ops_free_list.part.11+0x1c4/0x2d0
[  753.255241]  unregister_pernet_operations+0x262/0x390
[ ... ]
[  753.285883] list_add corruption. next->prev should be prev (ffff8880d48f2458), but was ffff8880d497d878. (next.
[  753.287241] ------------[ cut here ]------------
[  753.287794] kernel BUG at lib/list_debug.c:25!
[  753.288364] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[  753.289099] CPU: 0 PID: 7126 Comm: gtp-link Tainted: G    B   W         5.2.0-rc6+ #50
[  753.291036] RIP: 0010:__list_add_valid+0x74/0xd0
[  753.291589] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 89 d9 48b
[  753.293779] RSP: 0018:ffff8880cae8f398 EFLAGS: 00010286
[  753.294401] RAX: 0000000000000075 RBX: ffff8880d497d878 RCX: 0000000000000000
[  753.296260] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed10195d1e69
[  753.297070] RBP: ffff8880cd250ae0 R08: ffffed101b4bff21 R09: ffffed101b4bff21
[  753.297899] R10: 0000000000000001 R11: ffffed101b4bff20 R12: ffff8880d497d878
[  753.298703] R13: 0000000000000000 R14: ffff8880cd250ae0 R15: ffff8880d48f2458
[  753.299564] FS:  00007f5f79805740(0000) GS:ffff8880da400000(0000) knlGS:0000000000000000
[  753.300533] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  753.301231] CR2: 00007fe8c7ef4f10 CR3: 00000000b71a6006 CR4: 00000000000606f0
[  753.302183] Call Trace:
[  753.302530]  gtp_newlink+0x5f6/0xa5c [gtp]
[  753.303037]  ? __netlink_ns_capable+0xc3/0xf0
[  753.303576]  __rtnl_newlink+0xb9f/0x11b0
[  753.304092]  ? rtnl_link_unregister+0x230/0x230

Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/gtp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/gtp.c b/drivers/net/gtp.c
index 53fd66534e3a..5de4053774b8 100644
--- a/drivers/net/gtp.c
+++ b/drivers/net/gtp.c
@@ -1383,9 +1383,9 @@ late_initcall(gtp_init);
 
 static void __exit gtp_fini(void)
 {
-	unregister_pernet_subsys(&gtp_net_ops);
 	genl_unregister_family(&gtp_genl_family);
 	rtnl_link_unregister(&gtp_link_ops);
+	unregister_pernet_subsys(&gtp_net_ops);
 
 	pr_info("GTP module unloaded\n");
 }
-- 
2.20.1

[PATCH AUTOSEL 4.14 105/105] net: mvmdio: defer probe of orion-mdio if a clock is not ready

[Sasha Levin]

From: Josua Mayer <josua@solid-run.com>

[ Upstream commit 433a06d7d74e677c40b1148c70c48677ff62fb6b ]

Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.

Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/marvell/mvmdio.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvmdio.c b/drivers/net/ethernet/marvell/mvmdio.c
index 0495487f7b42..c8e3c1119313 100644
--- a/drivers/net/ethernet/marvell/mvmdio.c
+++ b/drivers/net/ethernet/marvell/mvmdio.c
@@ -321,6 +321,10 @@ static int orion_mdio_probe(struct platform_device *pdev)
 
 	for (i = 0; i < ARRAY_SIZE(dev->clk); i++) {
 		dev->clk[i] = of_clk_get(pdev->dev.of_node, i);
+		if (PTR_ERR(dev->clk[i]) == -EPROBE_DEFER) {
+			ret = -EPROBE_DEFER;
+			goto out_clk;
+		}
 		if (IS_ERR(dev->clk[i]))
 			break;
 		clk_prepare_enable(dev->clk[i]);
@@ -365,6 +369,7 @@ static int orion_mdio_probe(struct platform_device *pdev)
 	if (dev->err_interrupt > 0)
 		writel(0, dev->regs + MVMDIO_ERR_INT_MASK);
 
+out_clk:
 	for (i = 0; i < ARRAY_SIZE(dev->clk); i++) {
 		if (IS_ERR(dev->clk[i]))
 			break;
-- 
2.20.1