* [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts
@ 2019-05-15 8:49 Yinbo Zhu
2019-07-30 10:02 ` Yinbo Zhu
2019-08-03 7:00 ` Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Yinbo Zhu @ 2019-05-15 8:49 UTC (permalink / raw)
To: Shawn Guo, Li Yang, Rob Herring
Cc: yinbo.zhu, xiaobo.xie, Mark Rutland, linux-arm-kernel,
devicetree, linux-kernel, linux-mmc, yangbo.lu, jiafei.pan,
Ashish Kumar
From: Ashish Kumar <Ashish.Kumar@nxp.com>
This patch is to add esdhc node and enable SD UHS-I,
eMMC HS200 for ls1028ardb/ls1028aqds board.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
---
Change in v3:
replace "esdhc@" with "mmc@"
arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 8 ++++++
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 13 ++++++++++
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 27 +++++++++++++++++++++
3 files changed, 48 insertions(+), 0 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
index 14c79f4..180e5d2 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -42,6 +42,14 @@
status = "okay";
};
+&esdhc {
+ status = "okay";
+};
+
+&esdhc1 {
+ status = "okay";
+};
+
&i2c0 {
status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
index f86b054..1bfaf42 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -30,6 +30,19 @@
};
};
+&esdhc {
+ status = "okay";
+ sd-uhs-sdr104;
+ sd-uhs-sdr50;
+ sd-uhs-sdr25;
+ sd-uhs-sdr12;
+ };
+
+&esdhc1 {
+ status = "okay";
+ mmc-hs200-1_8v;
+ };
+
&i2c0 {
status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index 2896bbc..462833c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -274,6 +274,33 @@
status = "disabled";
};
+ esdhc: mmc@2140000 {
+ compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
+ reg = <0x0 0x2140000 0x0 0x10000>;
+ interrupts = <0 28 0x4>; /* Level high type */
+ clock-frequency = <0>; /* fixed up by bootloader */
+ clocks = <&clockgen 2 1>;
+ voltage-ranges = <1800 1800 3300 3300>;
+ sdhci,auto-cmd12;
+ little-endian;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ esdhc1: mmc@2150000 {
+ compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
+ reg = <0x0 0x2150000 0x0 0x10000>;
+ interrupts = <0 63 0x4>; /* Level high type */
+ clock-frequency = <0>; /* fixed up by bootloader */
+ clocks = <&clockgen 2 1>;
+ voltage-ranges = <1800 1800 3300 3300>;
+ sdhci,auto-cmd12;
+ broken-cd;
+ little-endian;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
sata: sata@3200000 {
compatible = "fsl,ls1028a-ahci";
reg = <0x0 0x3200000 0x0 0x10000>,
--
1.7.1
^ permalink raw reply related [flat|nested] 3+ messages in thread* RE: [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts
2019-05-15 8:49 [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts Yinbo Zhu
@ 2019-07-30 10:02 ` Yinbo Zhu
2019-08-03 7:00 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Yinbo Zhu @ 2019-07-30 10:02 UTC (permalink / raw)
To: Shawn Guo, Leo Li, Rob Herring
Cc: Xiaobo Xie, Mark Rutland, linux-arm-kernel, devicetree,
linux-kernel, linux-mmc, Y.b. Lu, Jiafei Pan, Ashish Kumar,
Yinbo Zhu
Hi,
I just check mmc upstream code, that patch still not upstream.
Please help merge it to upstream tree.
Thanks
Regards,
Yinbo Zhu
> -----Original Message-----
> From: Yinbo Zhu [mailto:yinbo.zhu@nxp.com]
> Sent: 2019年5月15日 16:49
> To: Shawn Guo <shawnguo@kernel.org>; Leo Li <leoyang.li@nxp.com>; Rob
> Herring <robh+dt@kernel.org>
> Cc: Yinbo Zhu <yinbo.zhu@nxp.com>; Xiaobo Xie <xiaobo.xie@nxp.com>; Mark
> Rutland <mark.rutland@arm.com>; linux-arm-kernel@lists.infradead.org;
> devicetree@vger.kernel.org; linux-kernel@vger.kernel.org;
> linux-mmc@vger.kernel.org; Y.b. Lu <yangbo.lu@nxp.com>; Jiafei Pan
> <jiafei.pan@nxp.com>; Ashish Kumar <ashish.kumar@nxp.com>
> Subject: [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts
>
> From: Ashish Kumar <Ashish.Kumar@nxp.com>
>
> This patch is to add esdhc node and enable SD UHS-I, eMMC HS200 for
> ls1028ardb/ls1028aqds board.
>
> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
> ---
> Change in v3:
> replace "esdhc@" with "mmc@"
>
> arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 8 ++++++
> arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 13 ++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 27
> +++++++++++++++++++++
> 3 files changed, 48 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> index 14c79f4..180e5d2 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> @@ -42,6 +42,14 @@
> status = "okay";
> };
>
> +&esdhc {
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + status = "okay";
> +};
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> index f86b054..1bfaf42 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> @@ -30,6 +30,19 @@
> };
> };
>
> +&esdhc {
> + status = "okay";
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + };
> +
> +&esdhc1 {
> + status = "okay";
> + mmc-hs200-1_8v;
> + };
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> index 2896bbc..462833c 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -274,6 +274,33 @@
> status = "disabled";
> };
>
> + esdhc: mmc@2140000 {
> + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
> + reg = <0x0 0x2140000 0x0 0x10000>;
> + interrupts = <0 28 0x4>; /* Level high type */
> + clock-frequency = <0>; /* fixed up by bootloader */
> + clocks = <&clockgen 2 1>;
> + voltage-ranges = <1800 1800 3300 3300>;
> + sdhci,auto-cmd12;
> + little-endian;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> + esdhc1: mmc@2150000 {
> + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
> + reg = <0x0 0x2150000 0x0 0x10000>;
> + interrupts = <0 63 0x4>; /* Level high type */
> + clock-frequency = <0>; /* fixed up by bootloader */
> + clocks = <&clockgen 2 1>;
> + voltage-ranges = <1800 1800 3300 3300>;
> + sdhci,auto-cmd12;
> + broken-cd;
> + little-endian;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> sata: sata@3200000 {
> compatible = "fsl,ls1028a-ahci";
> reg = <0x0 0x3200000 0x0 0x10000>,
> --
> 1.7.1
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts
2019-05-15 8:49 [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts Yinbo Zhu
2019-07-30 10:02 ` Yinbo Zhu
@ 2019-08-03 7:00 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2019-08-03 7:00 UTC (permalink / raw)
To: Yinbo Zhu
Cc: Li Yang, Rob Herring, xiaobo.xie, Mark Rutland, linux-arm-kernel,
devicetree, linux-kernel, linux-mmc, yangbo.lu, jiafei.pan,
Ashish Kumar
On Wed, May 15, 2019 at 04:49:25PM +0800, Yinbo Zhu wrote:
> From: Ashish Kumar <Ashish.Kumar@nxp.com>
>
> This patch is to add esdhc node and enable SD UHS-I,
> eMMC HS200 for ls1028ardb/ls1028aqds board.
>
> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
> ---
> Change in v3:
> replace "esdhc@" with "mmc@"
>
> arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 8 ++++++
> arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 13 ++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 27 +++++++++++++++++++++
> 3 files changed, 48 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> index 14c79f4..180e5d2 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> @@ -42,6 +42,14 @@
> status = "okay";
> };
>
> +&esdhc {
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + status = "okay";
> +};
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> index f86b054..1bfaf42 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> @@ -30,6 +30,19 @@
> };
> };
>
> +&esdhc {
> + status = "okay";
We usually put 'status' at end of property list.
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + };
Please follow the indent style of closing parentheses in the file.
> +
> +&esdhc1 {
> + status = "okay";
> + mmc-hs200-1_8v;
> + };
Ditto
> +
> &i2c0 {
> status = "okay";
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> index 2896bbc..462833c 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -274,6 +274,33 @@
> status = "disabled";
> };
>
> + esdhc: mmc@2140000 {
Please sort the nodes in unit-address. From what I see, it should go
before device serial@21c0500.
> + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
> + reg = <0x0 0x2140000 0x0 0x10000>;
> + interrupts = <0 28 0x4>; /* Level high type */
Use IRQ_TYPE_LEVEL_HIGH, then you can drop the comment.
Shawn
> + clock-frequency = <0>; /* fixed up by bootloader */
> + clocks = <&clockgen 2 1>;
> + voltage-ranges = <1800 1800 3300 3300>;
> + sdhci,auto-cmd12;
> + little-endian;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> + esdhc1: mmc@2150000 {
> + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc";
> + reg = <0x0 0x2150000 0x0 0x10000>;
> + interrupts = <0 63 0x4>; /* Level high type */
> + clock-frequency = <0>; /* fixed up by bootloader */
> + clocks = <&clockgen 2 1>;
> + voltage-ranges = <1800 1800 3300 3300>;
> + sdhci,auto-cmd12;
> + broken-cd;
> + little-endian;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> sata: sata@3200000 {
> compatible = "fsl,ls1028a-ahci";
> reg = <0x0 0x3200000 0x0 0x10000>,
> --
> 1.7.1
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-08-03 7:00 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-15 8:49 [PATCH v3] arm64: dts: ls1028a: Add esdhc node in dts Yinbo Zhu
2019-07-30 10:02 ` Yinbo Zhu
2019-08-03 7:00 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).