* [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Anvo-Systems @ 2019-08-12 16:59 Krzysztof Kozlowski 2019-08-12 16:59 ` [PATCH v5 2/3] dt-bindings: eeprom: at25: Add Anvo ANV32E61W Krzysztof Kozlowski 2019-08-12 16:59 ` [PATCH v5 3/3] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards Krzysztof Kozlowski 0 siblings, 2 replies; 4+ messages in thread From: Krzysztof Kozlowski @ 2019-08-12 16:59 UTC (permalink / raw) To: Schrempf Frieder, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel Cc: Krzysztof Kozlowski Add vendor prefix for Anvo-Systems Dresden GmbH. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> --- Changes since v4: None Changes since v3: 1. Add Rob's tag, 2. Remove Admatec (not needed anymore). Changes since v2: 1. Use admatecde vendor prefix. 2. Add Anvo-Systems Dresden GmbH. Changes since v1: New patch --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 6992bbbbffab..519889f5aec8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -81,6 +81,8 @@ patternProperties: description: Analogix Semiconductor, Inc. "^andestech,.*": description: Andes Technology Corporation + "^anvo,.*": + description: Anvo-Systems Dresden GmbH "^apm,.*": description: Applied Micro Circuits Corporation (APM) "^aptina,.*": -- 2.17.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v5 2/3] dt-bindings: eeprom: at25: Add Anvo ANV32E61W 2019-08-12 16:59 [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Anvo-Systems Krzysztof Kozlowski @ 2019-08-12 16:59 ` Krzysztof Kozlowski 2019-08-12 16:59 ` [PATCH v5 3/3] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards Krzysztof Kozlowski 1 sibling, 0 replies; 4+ messages in thread From: Krzysztof Kozlowski @ 2019-08-12 16:59 UTC (permalink / raw) To: Schrempf Frieder, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel Cc: Krzysztof Kozlowski Document the compatible for ANV32E61W 64kb Serial SPI non-volatile SRAM. Although it is a SRAM device, it can be accessed through EEPROM interface. At least until there is no proper SRAM driver support for it. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Fabio Estevam <festevam@gmail.com> --- Changes since v4: 1. Update commit msg. --- Documentation/devicetree/bindings/eeprom/at25.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt index b3bde97dc199..42577dd113dd 100644 --- a/Documentation/devicetree/bindings/eeprom/at25.txt +++ b/Documentation/devicetree/bindings/eeprom/at25.txt @@ -3,6 +3,7 @@ EEPROMs (SPI) compatible with Atmel at25. Required properties: - compatible : Should be "<vendor>,<type>", and generic value "atmel,at25". Example "<vendor>,<type>" values: + "anvo,anv32e61w" "microchip,25lc040" "st,m95m02" "st,m95256" -- 2.17.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v5 3/3] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards 2019-08-12 16:59 [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Anvo-Systems Krzysztof Kozlowski 2019-08-12 16:59 ` [PATCH v5 2/3] dt-bindings: eeprom: at25: Add Anvo ANV32E61W Krzysztof Kozlowski @ 2019-08-12 16:59 ` Krzysztof Kozlowski 2019-08-19 11:41 ` Shawn Guo 1 sibling, 1 reply; 4+ messages in thread From: Krzysztof Kozlowski @ 2019-08-12 16:59 UTC (permalink / raw) To: Schrempf Frieder, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel Cc: Krzysztof Kozlowski Add support for i.MX6UL modules from Kontron Electronics GmbH (before acquisition: Exceet Electronics) and evalkit boards based on it: 1. N6310 SOM: i.MX6 UL System-on-Module, a 25x25 mm solderable module (LGA pads and pin castellations) with 256 MB RAM, 1 MB NOR-Flash, 256 MB NAND and other interfaces, 2. N6310 S: evalkit, w/wo eMMC, without display, 3. N6310 S 43: evalkit with 4.3" display, The work is based on Exceet/Kontron source code (GPLv2) with numerous changes: 1. Reorganize files, 2. Rename Exceet -> Kontron, 3. Rename models/compatibles to match newest Kontron product naming, 4. Fix coding style errors and adjust to device tree coding guidelines, 5. Fix DTC warnings, 6. Extend compatibles so eval boards inherit the SoM compatible, 7. Use defines instead of GPIO and interrupt flag values, 8. Use proper vendor compatible for Macronix SPI NOR, 9. Replace deprecated bindings with proper ones, 10. Sort nodes alphabetically, 11. Remove Admatec display nodes (not yet supported). Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> --- Changes since v4: None Changes since v3, after Shawn's review: 1. Split bindings update to patch 2/3, 2. Remove unsupported displays from (Admatec), 3. Remove N6310 S 50 board (same as N6310 S 43 since there is no Admatec display), 4. Order iomux nodes by name, minor cleanup, 5. Use wakeup-source instead of enable-sdio-wakeup, 6. Add review tags. Changes since v2, after Fabio's review: 1. Add "imx6ul" compatible to board name (that's what I understood from review), 2. Add vendor/device prefix to eeprom and document the compatible, 3. Use "admatecde" as vendor compatible to avoid confusion with Admatec AG in Switzerland (also making LCD panels), 4. Use generic names for nodes, 5. Use IRQ_TYPE_LEVEL_LOW, 6. Move iomux to the end of files, 7. Remove regulators node (include regulators in top level), 8. Remove cpu clock-frequency, 9. Other minor fixes pointed by Fabio. Changes since v1, after Frieder's review: 1. Remove unneeded license notes, 2. Add Kontron copyright (2018), 3. Rename the files/models/compatibles to new naming - N6310, 4. Remove unneeded CPU operating points override, 5. Switch regulator nodes into simple children nodes without addresses (so not simple bus), 6. Use proper vendor compatible for Macronix SPI NOR. --- .../devicetree/bindings/arm/fsl.yaml | 3 + arch/arm/boot/dts/Makefile | 2 + .../boot/dts/imx6ul-kontron-n6310-s-43.dts | 102 +++++ arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts | 420 ++++++++++++++++++ .../boot/dts/imx6ul-kontron-n6310-som.dtsi | 134 ++++++ 5 files changed, 661 insertions(+) create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 7294ac36f4c0..d07b3c06d7cf 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -161,6 +161,9 @@ properties: items: - enum: - fsl,imx6ul-14x14-evk # i.MX6 UltraLite 14x14 EVK Board + - kontron,imx6ul-n6310-som # Kontron N6310 SOM + - kontron,imx6ul-n6310-s # Kontron N6310 S Board + - kontron,imx6ul-n6310-s-43 # Kontron N6310 S 43 Board - const: fsl,imx6ul - description: i.MX6ULL based Boards diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 9159fa2cea90..747eef501f95 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -569,6 +569,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-geam.dtb \ imx6ul-isiot-emmc.dtb \ imx6ul-isiot-nand.dtb \ + imx6ul-kontron-n6310-s.dtb \ + imx6ul-kontron-n6310-s-43.dtb \ imx6ul-liteboard.dtb \ imx6ul-opos6uldev.dtb \ imx6ul-pico-hobbit.dtb \ diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts new file mode 100644 index 000000000000..5bad29683cc3 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts @@ -0,0 +1,102 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org> + */ + +#include "imx6ul-kontron-n6310-s.dts" + +/ { + model = "Kontron N6310 S 43"; + compatible = "kontron,imx6ul-n6310-s-43", "kontron,imx6ul-n6310-s", + "kontron,imx6ul-n6310-som", "fsl,imx6ul"; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm7 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + status = "okay"; + }; +}; + +&i2c4 { + touchscreen@5d { + compatible = "goodix,gt928"; + reg = <0x5d>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cap_touch>; + interrupt-parent = <&gpio5>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; + irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>; + /* Leave status disabled because of missing display panel node */ +}; + +&pwm7 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm7>; + status = "okay"; +}; + +&iomuxc { + pinctrl_cap_touch: captouchgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* Touch Interrupt */ + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* Touch Reset */ + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Touch Wake */ + >; + }; + + pinctrl_lcdif_ctrl: lcdifctrlgrp { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79 + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79 + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79 + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79 + MX6UL_PAD_LCD_RESET__LCDIF_RESET 0x79 + >; + }; + + pinctrl_lcdif_dat: lcdifdatgrp { + fsl,pins = < + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79 + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79 + >; + }; + + pinctrl_pwm7: pwm7grp { + fsl,pins = < + MX6UL_PAD_CSI_VSYNC__PWM7_OUT 0x110b0 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts new file mode 100644 index 000000000000..0205fd56d975 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts @@ -0,0 +1,420 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org> + */ + +/dts-v1/; + +#include "imx6ul-kontron-n6310-som.dtsi" + +/ { + model = "Kontron N6310 S"; + compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som", + "fsl,imx6ul"; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led1 { + label = "debug-led1"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led2 { + label = "debug-led2"; + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led3 { + label = "debug-led3"; + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&pwm8 0 5000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vref_adc: regulator-vref-adc { + compatible = "regulator-fixed"; + regulator-name = "vref-adc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + num-channels = <3>; + vref-supply = <®_vref_adc>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + eeprom@0 { + compatible = "anvo,anv32e61w", "atmel,at25"; + reg = <0>; + spi-max-frequency = <20000000>; + spi-cpha; + spi-cpol; + pagesize = <1>; + size = <8192>; + address-width = <16>; + }; +}; + +&fec1 { + pinctrl-0 = <&pinctrl_enet1>; + /delete-node/ mdio; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>; + phy-mode = "rmii"; + phy-handle = <ðphy2>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; +}; + +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm8>; + status = "okay"; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + rs485-rx-during-tx; + rs485-rts-active-low; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_3v3>; + voltage-ranges = <3300 3300>; + no-1-8-v; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + non-removable; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_3v3>; + voltage-ranges = <3300 3300>; + no-1-8-v; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; + + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0 + >; + }; + + /* FRAM */ + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1 + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */ + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009 + >; + }; + + pinctrl_enet2_mdio: enet2mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_gpio: gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */ + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */ + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */ + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */ + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0 + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0 + >; + }; + + pinctrl_pwm8: pwm8grp { + fsl,pins = < + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1 + /* + * mux unused RTS to make sure it doesn't cause + * any interrupts when it is undefined + */ + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1 + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1 + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usbotg1: usbotg1 { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi new file mode 100644 index 000000000000..a896b2348dd2 --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi @@ -0,0 +1,134 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org> + */ + +#include "imx6ul.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Kontron N6310 SOM"; + compatible = "kontron,imx6ul-n6310-som", "fsl,imx6ul"; + + memory@80000000 { + reg = <0x80000000 0x10000000>; + device_type = "memory"; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + spi-flash@0 { + compatible = "mxicy,mx25v8035f", "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&fec2 { + phy-mode = "rmii"; + status = "disabled"; +}; + +&qspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + spi-max-frequency = <108000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + reg = <0>; + + partition@0 { + label = "ubi1"; + reg = <0x00000000 0x08000000>; + }; + + partition@8000000 { + label = "ubi2"; + reg = <0x08000000 0x08000000>; + }; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reset_out>; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1 + MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009 + >; + }; + + pinctrl_enet1_mdio: enet1mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 + >; + }; + + pinctrl_reset_out: rstoutgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0 + >; + }; +}; -- 2.17.1 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v5 3/3] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards 2019-08-12 16:59 ` [PATCH v5 3/3] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards Krzysztof Kozlowski @ 2019-08-19 11:41 ` Shawn Guo 0 siblings, 0 replies; 4+ messages in thread From: Shawn Guo @ 2019-08-19 11:41 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Schrempf Frieder, Rob Herring, Mark Rutland, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel On Mon, Aug 12, 2019 at 06:59:09PM +0200, Krzysztof Kozlowski wrote: > Add support for i.MX6UL modules from Kontron Electronics GmbH (before > acquisition: Exceet Electronics) and evalkit boards based on it: > > 1. N6310 SOM: i.MX6 UL System-on-Module, a 25x25 mm solderable module > (LGA pads and pin castellations) with 256 MB RAM, 1 MB NOR-Flash, > 256 MB NAND and other interfaces, > 2. N6310 S: evalkit, w/wo eMMC, without display, > 3. N6310 S 43: evalkit with 4.3" display, > > The work is based on Exceet/Kontron source code (GPLv2) with numerous > changes: > 1. Reorganize files, > 2. Rename Exceet -> Kontron, > 3. Rename models/compatibles to match newest Kontron product naming, > 4. Fix coding style errors and adjust to device tree coding guidelines, > 5. Fix DTC warnings, > 6. Extend compatibles so eval boards inherit the SoM compatible, > 7. Use defines instead of GPIO and interrupt flag values, > 8. Use proper vendor compatible for Macronix SPI NOR, > 9. Replace deprecated bindings with proper ones, > 10. Sort nodes alphabetically, > 11. Remove Admatec display nodes (not yet supported). > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> > Reviewed-by: Rob Herring <robh@kernel.org> > Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> > Reviewed-by: Fabio Estevam <festevam@gmail.com> > > --- > > Changes since v4: > None > > Changes since v3, after Shawn's review: > 1. Split bindings update to patch 2/3, > 2. Remove unsupported displays from (Admatec), > 3. Remove N6310 S 50 board (same as N6310 S 43 since there is no Admatec > display), > 4. Order iomux nodes by name, minor cleanup, > 5. Use wakeup-source instead of enable-sdio-wakeup, > 6. Add review tags. > > Changes since v2, after Fabio's review: > 1. Add "imx6ul" compatible to board name (that's what I understood from > review), > 2. Add vendor/device prefix to eeprom and document the compatible, > 3. Use "admatecde" as vendor compatible to avoid confusion with Admatec > AG in Switzerland (also making LCD panels), > 4. Use generic names for nodes, > 5. Use IRQ_TYPE_LEVEL_LOW, > 6. Move iomux to the end of files, > 7. Remove regulators node (include regulators in top level), > 8. Remove cpu clock-frequency, > 9. Other minor fixes pointed by Fabio. > > Changes since v1, after Frieder's review: > 1. Remove unneeded license notes, > 2. Add Kontron copyright (2018), > 3. Rename the files/models/compatibles to new naming - N6310, > 4. Remove unneeded CPU operating points override, > 5. Switch regulator nodes into simple children nodes without addresses > (so not simple bus), > 6. Use proper vendor compatible for Macronix SPI NOR. > --- > .../devicetree/bindings/arm/fsl.yaml | 3 + Sorry that I did not make it clear, but this needs to be a separate patch as well. Shawn > arch/arm/boot/dts/Makefile | 2 + > .../boot/dts/imx6ul-kontron-n6310-s-43.dts | 102 +++++ > arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts | 420 ++++++++++++++++++ > .../boot/dts/imx6ul-kontron-n6310-som.dtsi | 134 ++++++ > 5 files changed, 661 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts > create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts > create mode 100644 arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi > > diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml > index 7294ac36f4c0..d07b3c06d7cf 100644 > --- a/Documentation/devicetree/bindings/arm/fsl.yaml > +++ b/Documentation/devicetree/bindings/arm/fsl.yaml > @@ -161,6 +161,9 @@ properties: > items: > - enum: > - fsl,imx6ul-14x14-evk # i.MX6 UltraLite 14x14 EVK Board > + - kontron,imx6ul-n6310-som # Kontron N6310 SOM > + - kontron,imx6ul-n6310-s # Kontron N6310 S Board > + - kontron,imx6ul-n6310-s-43 # Kontron N6310 S 43 Board > - const: fsl,imx6ul > > - description: i.MX6ULL based Boards > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 9159fa2cea90..747eef501f95 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -569,6 +569,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ > imx6ul-geam.dtb \ > imx6ul-isiot-emmc.dtb \ > imx6ul-isiot-nand.dtb \ > + imx6ul-kontron-n6310-s.dtb \ > + imx6ul-kontron-n6310-s-43.dtb \ > imx6ul-liteboard.dtb \ > imx6ul-opos6uldev.dtb \ > imx6ul-pico-hobbit.dtb \ > diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts > new file mode 100644 > index 000000000000..5bad29683cc3 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts > @@ -0,0 +1,102 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2017 exceet electronics GmbH > + * Copyright (C) 2018 Kontron Electronics GmbH > + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org> > + */ > + > +#include "imx6ul-kontron-n6310-s.dts" > + > +/ { > + model = "Kontron N6310 S 43"; > + compatible = "kontron,imx6ul-n6310-s-43", "kontron,imx6ul-n6310-s", > + "kontron,imx6ul-n6310-som", "fsl,imx6ul"; > + > + backlight { > + compatible = "pwm-backlight"; > + pwms = <&pwm7 0 5000000>; > + brightness-levels = <0 4 8 16 32 64 128 255>; > + default-brightness-level = <6>; > + status = "okay"; > + }; > +}; > + > +&i2c4 { > + touchscreen@5d { > + compatible = "goodix,gt928"; > + reg = <0x5d>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_cap_touch>; > + interrupt-parent = <&gpio5>; > + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; > + reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; > + irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +&lcdif { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>; > + /* Leave status disabled because of missing display panel node */ > +}; > + > +&pwm7 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm7>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_cap_touch: captouchgrp { > + fsl,pins = < > + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* Touch Interrupt */ > + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* Touch Reset */ > + MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Touch Wake */ > + >; > + }; > + > + pinctrl_lcdif_ctrl: lcdifctrlgrp { > + fsl,pins = < > + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79 > + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79 > + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79 > + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79 > + MX6UL_PAD_LCD_RESET__LCDIF_RESET 0x79 > + >; > + }; > + > + pinctrl_lcdif_dat: lcdifdatgrp { > + fsl,pins = < > + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79 > + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79 > + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79 > + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79 > + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79 > + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79 > + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79 > + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79 > + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79 > + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79 > + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79 > + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79 > + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79 > + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79 > + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79 > + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79 > + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79 > + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79 > + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79 > + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79 > + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79 > + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79 > + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79 > + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79 > + >; > + }; > + > + pinctrl_pwm7: pwm7grp { > + fsl,pins = < > + MX6UL_PAD_CSI_VSYNC__PWM7_OUT 0x110b0 > + >; > + }; > +}; > diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts > new file mode 100644 > index 000000000000..0205fd56d975 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts > @@ -0,0 +1,420 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2017 exceet electronics GmbH > + * Copyright (C) 2018 Kontron Electronics GmbH > + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org> > + */ > + > +/dts-v1/; > + > +#include "imx6ul-kontron-n6310-som.dtsi" > + > +/ { > + model = "Kontron N6310 S"; > + compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som", > + "fsl,imx6ul"; > + > + gpio-leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_leds>; > + > + led1 { > + label = "debug-led1"; > + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + linux,default-trigger = "heartbeat"; > + }; > + > + led2 { > + label = "debug-led2"; > + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + led3 { > + label = "debug-led3"; > + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + }; > + > + pwm-beeper { > + compatible = "pwm-beeper"; > + pwms = <&pwm8 0 5000>; > + }; > + > + reg_3v3: regulator-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + reg_usb_otg1_vbus: regulator-usb-otg1-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_vref_adc: regulator-vref-adc { > + compatible = "regulator-fixed"; > + regulator-name = "vref-adc"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > +}; > + > +&adc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_adc1>; > + num-channels = <3>; > + vref-supply = <®_vref_adc>; > + status = "okay"; > +}; > + > +&can2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_flexcan2>; > + status = "okay"; > +}; > + > +&ecspi1 { > + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi1>; > + status = "okay"; > + > + eeprom@0 { > + compatible = "anvo,anv32e61w", "atmel,at25"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + spi-cpha; > + spi-cpol; > + pagesize = <1>; > + size = <8192>; > + address-width = <16>; > + }; > +}; > + > +&fec1 { > + pinctrl-0 = <&pinctrl_enet1>; > + /delete-node/ mdio; > +}; > + > +&fec2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>; > + phy-mode = "rmii"; > + phy-handle = <ðphy2>; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy1: ethernet-phy@1 { > + reg = <1>; > + micrel,led-mode = <0>; > + clocks = <&clks IMX6UL_CLK_ENET_REF>; > + clock-names = "rmii-ref"; > + }; > + > + ethphy2: ethernet-phy@2 { > + reg = <2>; > + micrel,led-mode = <0>; > + clocks = <&clks IMX6UL_CLK_ENET2_REF>; > + clock-names = "rmii-ref"; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > +}; > + > +&i2c4 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c4>; > + status = "okay"; > + > + rtc@32 { > + compatible = "epson,rx8900"; > + reg = <0x32>; > + }; > +}; > + > +&pwm8 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pwm8>; > + status = "okay"; > +}; > + > +&snvs_poweroff { > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + linux,rs485-enabled-at-boot-time; > + rs485-rx-during-tx; > + rs485-rts-active-low; > + uart-has-rtscts; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + fsl,uart-has-rtscts; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4>; > + status = "okay"; > +}; > + > +&usbotg1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg1>; > + dr_mode = "otg"; > + srp-disable; > + hnp-disable; > + adp-disable; > + vbus-supply = <®_usb_otg1_vbus>; > + status = "okay"; > +}; > + > +&usbotg2 { > + dr_mode = "host"; > + disable-over-current; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; > + keep-power-in-suspend; > + wakeup-source; > + vmmc-supply = <®_3v3>; > + voltage-ranges = <3300 3300>; > + no-1-8-v; > + status = "okay"; > +}; > + > +&usdhc2 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc2>; > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; > + non-removable; > + keep-power-in-suspend; > + wakeup-source; > + vmmc-supply = <®_3v3>; > + voltage-ranges = <3300 3300>; > + no-1-8-v; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog>; > + fsl,ext-reset-output; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; > + > + pinctrl_adc1: adc1grp { > + fsl,pins = < > + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 > + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 > + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0 > + >; > + }; > + > + /* FRAM */ > + pinctrl_ecspi1: ecspi1grp { > + fsl,pins = < > + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1 > + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1 > + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1 > + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */ > + >; > + }; > + > + pinctrl_enet2: enet2grp { > + fsl,pins = < > + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 > + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 > + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 > + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 > + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 > + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 > + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 > + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009 > + >; > + }; > + > + pinctrl_enet2_mdio: enet2mdiogrp { > + fsl,pins = < > + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 > + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 > + >; > + }; > + > + pinctrl_flexcan2: flexcan2grp{ > + fsl,pins = < > + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 > + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 > + >; > + }; > + > + pinctrl_gpio: gpiogrp { > + fsl,pins = < > + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */ > + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */ > + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */ > + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */ > + >; > + }; > + > + pinctrl_gpio_leds: gpioledsgrp { > + fsl,pins = < > + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */ > + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */ > + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */ > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 > + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 > + >; > + }; > + > + pinctrl_i2c4: i2c4grp { > + fsl,pins = < > + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0 > + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0 > + >; > + }; > + > + pinctrl_pwm8: pwm8grp { > + fsl,pins = < > + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0 > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 > + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1 > + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1 > + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1 > + /* > + * mux unused RTS to make sure it doesn't cause > + * any interrupts when it is undefined > + */ > + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1 > + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1 > + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1 > + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1 > + >; > + }; > + > + pinctrl_uart4: uart4grp { > + fsl,pins = < > + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1 > + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1 > + >; > + }; > + > + pinctrl_usbotg1: usbotg1 { > + fsl,pins = < > + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0 > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 > + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 > + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 > + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 > + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 > + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 > + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */ > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 > + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 > + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 > + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 > + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 > + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 > + >; > + }; > + > + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { > + fsl,pins = < > + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 > + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 > + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 > + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 > + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 > + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 > + >; > + }; > + > + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { > + fsl,pins = < > + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 > + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 > + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 > + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 > + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 > + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 > + >; > + }; > + > + pinctrl_wdog: wdoggrp { > + fsl,pins = < > + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 > + >; > + }; > +}; > diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi > new file mode 100644 > index 000000000000..a896b2348dd2 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi > @@ -0,0 +1,134 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2017 exceet electronics GmbH > + * Copyright (C) 2018 Kontron Electronics GmbH > + * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org> > + */ > + > +#include "imx6ul.dtsi" > +#include <dt-bindings/gpio/gpio.h> > + > +/ { > + model = "Kontron N6310 SOM"; > + compatible = "kontron,imx6ul-n6310-som", "fsl,imx6ul"; > + > + memory@80000000 { > + reg = <0x80000000 0x10000000>; > + device_type = "memory"; > + }; > +}; > + > +&ecspi2 { > + cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi2>; > + status = "okay"; > + > + spi-flash@0 { > + compatible = "mxicy,mx25v8035f", "jedec,spi-nor"; > + spi-max-frequency = <50000000>; > + reg = <0>; > + }; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>; > + phy-mode = "rmii"; > + phy-handle = <ðphy1>; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy1: ethernet-phy@1 { > + reg = <1>; > + micrel,led-mode = <0>; > + clocks = <&clks IMX6UL_CLK_ENET_REF>; > + clock-names = "rmii-ref"; > + }; > + }; > +}; > + > +&fec2 { > + phy-mode = "rmii"; > + status = "disabled"; > +}; > + > +&qspi { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_qspi>; > + status = "okay"; > + > + spi-flash@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "spi-nand"; > + spi-max-frequency = <108000000>; > + spi-tx-bus-width = <4>; > + spi-rx-bus-width = <4>; > + reg = <0>; > + > + partition@0 { > + label = "ubi1"; > + reg = <0x00000000 0x08000000>; > + }; > + > + partition@8000000 { > + label = "ubi2"; > + reg = <0x08000000 0x08000000>; > + }; > + }; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reset_out>; > + > + pinctrl_ecspi2: ecspi2grp { > + fsl,pins = < > + MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1 > + MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1 > + MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1 > + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1 > + >; > + }; > + > + pinctrl_enet1: enet1grp { > + fsl,pins = < > + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 > + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 > + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 > + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 > + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 > + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 > + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 > + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009 > + >; > + }; > + > + pinctrl_enet1_mdio: enet1mdiogrp { > + fsl,pins = < > + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 > + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 > + >; > + }; > + > + pinctrl_qspi: qspigrp { > + fsl,pins = < > + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 > + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 > + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 > + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 > + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 > + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 > + >; > + }; > + > + pinctrl_reset_out: rstoutgrp { > + fsl,pins = < > + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0 > + >; > + }; > +}; > -- > 2.17.1 > ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2019-08-19 11:41 UTC | newest] Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-08-12 16:59 [PATCH v5 1/3] dt-bindings: vendor-prefixes: Add Anvo-Systems Krzysztof Kozlowski 2019-08-12 16:59 ` [PATCH v5 2/3] dt-bindings: eeprom: at25: Add Anvo ANV32E61W Krzysztof Kozlowski 2019-08-12 16:59 ` [PATCH v5 3/3] ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards Krzysztof Kozlowski 2019-08-19 11:41 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).