[PATCH V2 net-next 0/4] net: ethernet: stmmac: cleanup clock and optimization

[PATCH V2 net-next 0/4] net: ethernet: stmmac: cleanup clock and optimization

[Christophe Roullier]

Some improvements: 
 - manage syscfg as optional clock, 
 - update slew rate of ETH_MDIO pin, 
 - Enable gating of the MAC TX clock during TX low-power mode

V2: Update with D.Miller remark

Christophe Roullier (4):
  net: ethernet: stmmac: Add support for syscfg clock
  ARM: dts: stm32: remove syscfg clock on stm32mp157c ethernet
  ARM: dts: stm32: adjust slew rate for Ethernet
  ARM: dts: stm32: Enable gating of the MAC TX clock during TX low-power
    mode on stm32mp157c

 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi     |  9 ++++--
 arch/arm/boot/dts/stm32mp157c.dtsi            |  7 ++--
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 32 ++++++++++++-------
 3 files changed, 31 insertions(+), 17 deletions(-)

-- 
2.17.1

[PATCH V2 net-next 1/4] net: ethernet: stmmac: Add support for syscfg clock

[Christophe Roullier]

Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 32 ++++++++++++-------
 1 file changed, 21 insertions(+), 11 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
index 4ef041bdf6a1..df7e9e913041 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
@@ -152,19 +152,24 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
 	int ret = 0;
 
 	if (prepare) {
-		ret = clk_prepare_enable(dwmac->syscfg_clk);
-		if (ret)
-			return ret;
-
+		if (dwmac->syscfg_clk) {
+			ret = clk_prepare_enable(dwmac->syscfg_clk);
+			if (ret)
+				return ret;
+		}
 		if (dwmac->clk_eth_ck) {
 			ret = clk_prepare_enable(dwmac->clk_eth_ck);
 			if (ret) {
-				clk_disable_unprepare(dwmac->syscfg_clk);
+				if (dwmac->syscfg_clk)
+					clk_disable_unprepare
+						(dwmac->syscfg_clk);
 				return ret;
 			}
 		}
 	} else {
-		clk_disable_unprepare(dwmac->syscfg_clk);
+		if (dwmac->syscfg_clk)
+			clk_disable_unprepare(dwmac->syscfg_clk);
+
 		if (dwmac->clk_eth_ck)
 			clk_disable_unprepare(dwmac->clk_eth_ck);
 	}
@@ -296,7 +301,7 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
 {
 	struct platform_device *pdev = to_platform_device(dev);
 	struct device_node *np = dev->of_node;
-	int err = 0;
+	int err;
 
 	/* Gigabit Ethernet 125MHz clock selection. */
 	dwmac->eth_clk_sel_reg = of_property_read_bool(np, "st,eth-clk-sel");
@@ -320,13 +325,17 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
 		return PTR_ERR(dwmac->clk_ethstp);
 	}
 
-	/*  Clock for sysconfig */
+	/*  Optional Clock for sysconfig */
 	dwmac->syscfg_clk = devm_clk_get(dev, "syscfg-clk");
 	if (IS_ERR(dwmac->syscfg_clk)) {
-		dev_err(dev, "No syscfg clock provided...\n");
-		return PTR_ERR(dwmac->syscfg_clk);
+		err = PTR_ERR(dwmac->syscfg_clk);
+		if (err != -ENOENT)
+			return err;
+		dwmac->syscfg_clk = NULL;
 	}
 
+	err = 0;
+
 	/* Get IRQ information early to have an ability to ask for deferred
 	 * probe if needed before we went too far with resource allocation.
 	 */
@@ -436,7 +445,8 @@ static int stm32mp1_suspend(struct stm32_dwmac *dwmac)
 		return ret;
 
 	clk_disable_unprepare(dwmac->clk_tx);
-	clk_disable_unprepare(dwmac->syscfg_clk);
+	if (dwmac->syscfg_clk)
+		clk_disable_unprepare(dwmac->syscfg_clk);
 	if (dwmac->clk_eth_ck)
 		clk_disable_unprepare(dwmac->clk_eth_ck);
 
-- 
2.17.1

[PATCH V2 net-next 2/4] ARM: dts: stm32: remove syscfg clock on stm32mp157c ethernet

[Christophe Roullier]

Syscfg is now activated automatically when syscfg registers are used

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
 arch/arm/boot/dts/stm32mp157c.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index 9b11654a0a39..f13c2348d130 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -1326,13 +1326,11 @@
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",
-				      "ethstp",
-				      "syscfg-clk";
+				      "ethstp";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
-				 <&rcc ETHSTP>,
-				 <&rcc SYSCFG>;
+				 <&rcc ETHSTP>;
 			st,syscon = <&syscfg 0x4>;
 			snps,mixed-burst;
 			snps,pbl = <2>;
-- 
2.17.1

[PATCH V2 net-next 3/4] ARM: dts: stm32: adjust slew rate for Ethernet

[Christophe Roullier]

ETH_MDIO slew-rate should be set to "0" instead of "2"

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
 arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 0a3a7d66737b..9a8f0d4c9ea3 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -217,13 +217,18 @@
 						 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
 						 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
 						 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
-						 <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */
 						 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
 					bias-disable;
 					drive-push-pull;
-					slew-rate = <3>;
+					slew-rate = <2>;
 				};
 				pins2 {
+					pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins3 {
 					pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
 						 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
 						 <STM32_PINMUX('B', 0, AF11)>, /* ETH_RGMII_RXD2 */
-- 
2.17.1

[PATCH V2 net-next 4/4] ARM: dts: stm32: Enable gating of the MAC TX clock during TX low-power mode on stm32mp157c

[Christophe Roullier]

When there is no activity on ethernet phy link, the ETH_GTX_CLK is cut

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
 arch/arm/boot/dts/stm32mp157c.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index f13c2348d130..8df2986dd452 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -1334,6 +1334,7 @@
 			st,syscon = <&syscfg 0x4>;
 			snps,mixed-burst;
 			snps,pbl = <2>;
+			snps,en-tx-lpi-clockgating;
 			snps,axi-config = <&stmmac_axi_config_0>;
 			snps,tso;
 			status = "disabled";
-- 
2.17.1

Re: [PATCH V2 net-next 1/4] net: ethernet: stmmac: Add support for syscfg clock

[Andrew Lunn]

On Tue, Nov 05, 2019 at 01:45:02PM +0100, Christophe Roullier wrote:
> Add optional support for syscfg clock in dwmac-stm32.c
> Now Syscfg clock is activated automatically when syscfg
> registers are used
> 
> Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
> ---
>  .../net/ethernet/stmicro/stmmac/dwmac-stm32.c | 32 ++++++++++++-------
>  1 file changed, 21 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
> index 4ef041bdf6a1..df7e9e913041 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
> @@ -152,19 +152,24 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
>  	int ret = 0;
>  
>  	if (prepare) {
> -		ret = clk_prepare_enable(dwmac->syscfg_clk);
> -		if (ret)
> -			return ret;
> -
> +		if (dwmac->syscfg_clk) {
> +			ret = clk_prepare_enable(dwmac->syscfg_clk);
> +			if (ret)
> +				return ret;
> +		}

Hi Christophe

All the clk_ API functions are happy to take a NULL point and then do
nothing. So you don't need these changes. 

> -	/*  Clock for sysconfig */
> +	/*  Optional Clock for sysconfig */
>  	dwmac->syscfg_clk = devm_clk_get(dev, "syscfg-clk");
>  	if (IS_ERR(dwmac->syscfg_clk)) {
> -		dev_err(dev, "No syscfg clock provided...\n");
> -		return PTR_ERR(dwmac->syscfg_clk);
> +		err = PTR_ERR(dwmac->syscfg_clk);
> +		if (err != -ENOENT)
> +			return err;
> +		dwmac->syscfg_clk = NULL;
>  	}
>  
> +	err = 0;
> +

That should be all you need. Just set dwmac->syscfg_clk to NULL and
the rest should work.

    Andrew