[PATCH v5 0/8] Add support for H6 PWM

[PATCH v5 0/8] Add support for H6 PWM

[Clément Péron]

Hi,

This is a rework of Jernej's previous work[1] taking account all the
previous remarks.

Bindings is still strict but probe in the driver are now optionnals.

If someone could confirm that the PWM is not broken, as my board
doesn't output it.

I didn't add the acked-tags as there are big changes.

Thanks,
Clément

Jernej's cover:
Allwinner H6 SoC has PWM core which is basically the same as that found
in A20, it's just depends on additional bus clock and reset line.

This series adds support for it and extends PWM driver functionality in
a way that it's now possible to bypass whole core and output PWM source
clock directly as a PWM signal. This functionality is needed by AC200
chip, which is bundled in same physical package as H6 SoC, to serve as a
clock source of 24 MHz. AC200 clock input pin is bonded internally to
the second PWM channel.

I would be grateful if anyone can test this patch series for any kind of
regression on other SoCs.

[1]: https://patchwork.kernel.org/cover/11061737/

Changes in v5:
 - Move bypass calculation to pwm_calculate
 - Split mod_clock fallback from bus_clk probe    
 - Update comment
 - Move my SoB after acked-by/reviewed-by

Changes in v4:
 - item description in correct order and add a blank line
 - use %pe for printing PTR_ERR
 - don't print error when it's an EPROBE_DEFER
 - change output clock bypass formula to match PWM policy

Changes in v3:
 - Documentation update to allow one clock without name
 - Change reset optional to shared
 - If reset probe failed return an error
 - Remove old clock probe
 - Update bypass enabled formula

Changes in v2:
 - Remove allOf in Documentation
 - Add H6 example in Documentation
 - Change clock name from "pwm" to "mod"
 - Change reset quirk to optional probe
 - Change bus_clock quirk to optional probe
 - Add limitation comment about mod_clk_output
 - Add quirk for mod_clk_output
 - Change bypass formula

Clément Péron (2):
  pwm: sun4i: Prefer "mod" clock to unamed
  [DO NOT MERGE] arm64: allwinner: h6: enable Beelink GS1 PWM

Jernej Skrabec (6):
  dt-bindings: pwm: allwinner: Add H6 PWM description
  pwm: sun4i: Add an optional probe for reset line
  pwm: sun4i: Add an optional probe for bus clock
  pwm: sun4i: Add support to output source clock directly
  pwm: sun4i: Add support for H6 PWM
  arm64: dts: allwinner: h6: Add PWM node

 .../bindings/pwm/allwinner,sun4i-a10-pwm.yaml |  48 +++++
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   |   4 +
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |  10 +
 drivers/pwm/pwm-sun4i.c                       | 185 +++++++++++++++---
 4 files changed, 215 insertions(+), 32 deletions(-)

-- 
2.20.1

[PATCH v5 1/8] dt-bindings: pwm: allwinner: Add H6 PWM description

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 PWM block is basically the same as A20 PWM, except that it also has
bus clock and reset line which needs to be handled accordingly.

Expand Allwinner PWM binding with H6 PWM specifics.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 .../bindings/pwm/allwinner,sun4i-a10-pwm.yaml | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml b/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml
index 0ac52f83a58c..1bae446febbb 100644
--- a/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml
+++ b/Documentation/devicetree/bindings/pwm/allwinner,sun4i-a10-pwm.yaml
@@ -30,13 +30,51 @@ properties:
       - items:
           - const: allwinner,sun50i-h5-pwm
           - const: allwinner,sun5i-a13-pwm
+      - const: allwinner,sun50i-h6-pwm
 
   reg:
     maxItems: 1
 
   clocks:
+    minItems: 1
+    maxItems: 2
+    items:
+      - description: Module Clock
+      - description: Bus Clock
+
+  # Even though it only applies to subschemas under the conditionals,
+  # not listing them here will trigger a warning because of the
+  # additionalsProperties set to false.
+  clock-names: true
+
+  resets:
     maxItems: 1
 
+  if:
+    properties:
+      compatible:
+        contains:
+          const: allwinner,sun50i-h6-pwm
+
+  then:
+    properties:
+      clocks:
+        maxItems: 2
+
+      clock-names:
+        items:
+          - const: mod
+          - const: bus
+
+    required:
+      - clock-names
+      - resets
+
+  else:
+    properties:
+      clocks:
+        maxItems: 1
+
 required:
   - "#pwm-cells"
   - compatible
@@ -54,4 +92,14 @@ examples:
         #pwm-cells = <3>;
     };
 
+  - |
+    pwm@300a000 {
+      compatible = "allwinner,sun50i-h6-pwm";
+      reg = <0x0300a000 0x400>;
+      clocks = <&osc24M>, <&ccu CLK_BUS_PWM>;
+      clock-names = "mod", "bus";
+      resets = <&ccu RST_BUS_PWM>;
+      #pwm-cells = <3>;
+    };
+
 ...
-- 
2.20.1

[PATCH v5 2/8] pwm: sun4i: Add an optional probe for reset line

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 PWM core needs deasserted reset line in order to work.

Add an optional probe for it.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/pwm/pwm-sun4i.c | 33 +++++++++++++++++++++++++++++++--
 1 file changed, 31 insertions(+), 2 deletions(-)

diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
index 581d23287333..c17935805690 100644
--- a/drivers/pwm/pwm-sun4i.c
+++ b/drivers/pwm/pwm-sun4i.c
@@ -16,6 +16,7 @@
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pwm.h>
+#include <linux/reset.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
 #include <linux/time.h>
@@ -78,6 +79,7 @@ struct sun4i_pwm_data {
 struct sun4i_pwm_chip {
 	struct pwm_chip chip;
 	struct clk *clk;
+	struct reset_control *rst;
 	void __iomem *base;
 	spinlock_t ctrl_lock;
 	const struct sun4i_pwm_data *data;
@@ -364,6 +366,21 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	if (IS_ERR(pwm->clk))
 		return PTR_ERR(pwm->clk);
 
+	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
+	if (IS_ERR(pwm->rst)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get reset failed %pe\n",
+				pwm->rst);
+		return PTR_ERR(pwm->rst);
+	}
+
+	/* Deassert reset */
+	ret = reset_control_deassert(pwm->rst);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot deassert reset control\n");
+		return ret;
+	}
+
 	pwm->chip.dev = &pdev->dev;
 	pwm->chip.ops = &sun4i_pwm_ops;
 	pwm->chip.base = -1;
@@ -376,19 +393,31 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	ret = pwmchip_add(&pwm->chip);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "failed to add PWM chip: %d\n", ret);
-		return ret;
+		goto err_pwm_add;
 	}
 
 	platform_set_drvdata(pdev, pwm);
 
 	return 0;
+
+err_pwm_add:
+	reset_control_assert(pwm->rst);
+
+	return ret;
 }
 
 static int sun4i_pwm_remove(struct platform_device *pdev)
 {
 	struct sun4i_pwm_chip *pwm = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = pwmchip_remove(&pwm->chip);
+	if (ret)
+		return ret;
+
+	reset_control_assert(pwm->rst);
 
-	return pwmchip_remove(&pwm->chip);
+	return 0;
 }
 
 static struct platform_driver sun4i_pwm_driver = {
-- 
2.20.1

[PATCH v5 3/8] pwm: sun4i: Prefer "mod" clock to unnamed

[Clément Péron]

New device tree bindings called the source clock of the module
"mod" when several clocks are defined.

Try to get a clock called "mod" if nothing is found try to get
an unnamed clock.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/pwm/pwm-sun4i.c | 29 +++++++++++++++++++++++++++--
 1 file changed, 27 insertions(+), 2 deletions(-)

diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
index c17935805690..bbb1ed194c0e 100644
--- a/drivers/pwm/pwm-sun4i.c
+++ b/drivers/pwm/pwm-sun4i.c
@@ -362,9 +362,34 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	if (IS_ERR(pwm->base))
 		return PTR_ERR(pwm->base);
 
-	pwm->clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(pwm->clk))
+	/*
+	 * All hardware variants need a source clock that is divided and
+	 * then feeds the counter that defines the output wave form. In the
+	 * device tree this clock is either unnamed or called "mod".
+	 * Some variants (e.g. H6) need another clock to access the
+	 * hardware registers; this is called "bus".
+	 * So we request "mod" first (and ignore the corner case that a
+	 * parent provides a "mod" clock while the right one would be the
+	 * unnamed one of the PWM device) and if this is not found we fall
+	 * back to the first clock of the PWM.
+	 */
+	pwm->clk = devm_clk_get_optional(&pdev->dev, "mod");
+	if (IS_ERR(pwm->clk)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get clock failed %pe\n",
+				pwm->clk);
 		return PTR_ERR(pwm->clk);
+	}
+
+	if (!pwm->clk) {
+		pwm->clk = devm_clk_get(&pdev->dev, NULL);
+		if (IS_ERR(pwm->clk)) {
+			if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "get clock failed %pe\n",
+					pwm->clk);
+			return PTR_ERR(pwm->clk);
+		}
+	}
 
 	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
 	if (IS_ERR(pwm->rst)) {
-- 
2.20.1

[PATCH v5 4/8] pwm: sun4i: Add an optional probe for bus clock

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

H6 PWM core needs bus clock to be enabled in order to work.

Add an optional probe for it and a fallback for previous
bindings without name on module clock.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/pwm/pwm-sun4i.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
index bbb1ed194c0e..93f4d44e9fa8 100644
--- a/drivers/pwm/pwm-sun4i.c
+++ b/drivers/pwm/pwm-sun4i.c
@@ -78,6 +78,7 @@ struct sun4i_pwm_data {
 
 struct sun4i_pwm_chip {
 	struct pwm_chip chip;
+	struct clk *bus_clk;
 	struct clk *clk;
 	struct reset_control *rst;
 	void __iomem *base;
@@ -391,6 +392,14 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 		}
 	}
 
+	pwm->bus_clk = devm_clk_get_optional(&pdev->dev, "bus");
+	if (IS_ERR(pwm->bus_clk)) {
+		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "get bus_clock failed %pe\n",
+				pwm->bus_clk);
+		return PTR_ERR(pwm->bus_clk);
+	}
+
 	pwm->rst = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
 	if (IS_ERR(pwm->rst)) {
 		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
@@ -406,6 +415,16 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	/*
+	 * We're keeping the bus clock on for the sake of simplicity.
+	 * Actually it only needs to be on for hardware register accesses.
+	 */
+	ret = clk_prepare_enable(pwm->bus_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot prepare and enable bus_clk\n");
+		goto err_bus;
+	}
+
 	pwm->chip.dev = &pdev->dev;
 	pwm->chip.ops = &sun4i_pwm_ops;
 	pwm->chip.base = -1;
@@ -426,6 +445,8 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
 	return 0;
 
 err_pwm_add:
+	clk_disable_unprepare(pwm->bus_clk);
+err_bus:
 	reset_control_assert(pwm->rst);
 
 	return ret;
@@ -440,6 +461,7 @@ static int sun4i_pwm_remove(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	clk_disable_unprepare(pwm->bus_clk);
 	reset_control_assert(pwm->rst);
 
 	return 0;
-- 
2.20.1

[PATCH v5 5/8] pwm: sun4i: Add support to output source clock directly

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

PWM core has an option to bypass whole logic and output unchanged source
clock as PWM output. This is achieved by enabling bypass bit.

Note that when bypass is enabled, no other setting has any meaning, not
even enable bit.

This mode of operation is needed to achieve high enough frequency to
serve as clock source for AC200 chip which is integrated into same
package as H6 SoC.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/pwm/pwm-sun4i.c | 92 ++++++++++++++++++++++++++++-------------
 1 file changed, 64 insertions(+), 28 deletions(-)

diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
index 93f4d44e9fa8..b64250b7e2be 100644
--- a/drivers/pwm/pwm-sun4i.c
+++ b/drivers/pwm/pwm-sun4i.c
@@ -3,6 +3,10 @@
  * Driver for Allwinner sun4i Pulse Width Modulation Controller
  *
  * Copyright (C) 2014 Alexandre Belloni <alexandre.belloni@free-electrons.com>
+ *
+ * Limitations:
+ * - When outputing the source clock directly, the PWM logic will be bypassed
+ *   and the currently running period is not guaranteed to be completed
  */
 
 #include <linux/bitops.h>
@@ -73,6 +77,7 @@ static const u32 prescaler_table[] = {
 
 struct sun4i_pwm_data {
 	bool has_prescaler_bypass;
+	bool has_direct_mod_clk_output;
 	unsigned int npwm;
 };
 
@@ -118,6 +123,20 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 	val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
+	/*
+	 * PWM chapter in H6 manual has a diagram which explains that if bypass
+	 * bit is set, no other setting has any meaning. Even more, experiment
+	 * proved that also enable bit is ignored in this case.
+	 */
+	if ((val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) &&
+	    sun4i_pwm->data->has_direct_mod_clk_output) {
+		state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, clk_rate);
+		state->duty_cycle = DIV_ROUND_UP_ULL(state->period, 2);
+		state->polarity = PWM_POLARITY_NORMAL;
+		state->enabled = true;
+		return;
+	}
+
 	if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
 	    sun4i_pwm->data->has_prescaler_bypass)
 		prescaler = 1;
@@ -149,13 +168,23 @@ static void sun4i_pwm_get_state(struct pwm_chip *chip,
 
 static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm,
 			       const struct pwm_state *state,
-			       u32 *dty, u32 *prd, unsigned int *prsclr)
+			       u32 *dty, u32 *prd, unsigned int *prsclr,
+			       bool *bypass)
 {
 	u64 clk_rate, div = 0;
 	unsigned int pval, prescaler = 0;
 
 	clk_rate = clk_get_rate(sun4i_pwm->clk);
 
+	*bypass = state->enabled &&
+		  (state->period * clk_rate >= NSEC_PER_SEC) &&
+		  (state->period * clk_rate < 2 * NSEC_PER_SEC) &&
+		  (state->duty_cycle * clk_rate * 2 >= NSEC_PER_SEC);
+
+	/* Skip calculation of other parameters if we bypass them */
+	if (*bypass && sun4i_pwm->data->has_direct_mod_clk_output)
+		return 0;
+
 	if (sun4i_pwm->data->has_prescaler_bypass) {
 		/* First, test without any prescaler when available */
 		prescaler = PWM_PRESCAL_MASK;
@@ -202,10 +231,11 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 {
 	struct sun4i_pwm_chip *sun4i_pwm = to_sun4i_pwm_chip(chip);
 	struct pwm_state cstate;
-	u32 ctrl;
+	u32 ctrl, period, duty, val;
 	int ret;
-	unsigned int delay_us;
+	unsigned int delay_us, prescaler;
 	unsigned long now;
+	bool bypass;
 
 	pwm_get_state(pwm, &cstate);
 
@@ -220,43 +250,48 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 	spin_lock(&sun4i_pwm->ctrl_lock);
 	ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
 
-	if ((cstate.period != state->period) ||
-	    (cstate.duty_cycle != state->duty_cycle)) {
-		u32 period, duty, val;
-		unsigned int prescaler;
+	ret = sun4i_pwm_calculate(sun4i_pwm, state, &duty, &period, &prescaler,
+				  &bypass);
+	if (ret) {
+		dev_err(chip->dev, "period exceeds the maximum value\n");
+		spin_unlock(&sun4i_pwm->ctrl_lock);
+		if (!cstate.enabled)
+			clk_disable_unprepare(sun4i_pwm->clk);
+		return ret;
+	}
 
-		ret = sun4i_pwm_calculate(sun4i_pwm, state,
-					  &duty, &period, &prescaler);
-		if (ret) {
-			dev_err(chip->dev, "period exceeds the maximum value\n");
-			spin_unlock(&sun4i_pwm->ctrl_lock);
-			if (!cstate.enabled)
-				clk_disable_unprepare(sun4i_pwm->clk);
-			return ret;
+	if (sun4i_pwm->data->has_direct_mod_clk_output) {
+		if (bypass) {
+			ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
+			/* We can skip apply of other parameters */
+			goto bypass_mode;
+		} else {
+			ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
 		}
+	}
 
-		if (PWM_REG_PRESCAL(ctrl, pwm->hwpwm) != prescaler) {
-			/* Prescaler changed, the clock has to be gated */
-			ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
-			sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
-
-			ctrl &= ~BIT_CH(PWM_PRESCAL_MASK, pwm->hwpwm);
-			ctrl |= BIT_CH(prescaler, pwm->hwpwm);
-		}
+	if (PWM_REG_PRESCAL(ctrl, pwm->hwpwm) != prescaler) {
+		/* Prescaler changed, the clock has to be gated */
+		ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
+		sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
 
-		val = (duty & PWM_DTY_MASK) | PWM_PRD(period);
-		sun4i_pwm_writel(sun4i_pwm, val, PWM_CH_PRD(pwm->hwpwm));
-		sun4i_pwm->next_period[pwm->hwpwm] = jiffies +
-			usecs_to_jiffies(cstate.period / 1000 + 1);
-		sun4i_pwm->needs_delay[pwm->hwpwm] = true;
+		ctrl &= ~BIT_CH(PWM_PRESCAL_MASK, pwm->hwpwm);
+		ctrl |= BIT_CH(prescaler, pwm->hwpwm);
 	}
 
+	val = (duty & PWM_DTY_MASK) | PWM_PRD(period);
+	sun4i_pwm_writel(sun4i_pwm, val, PWM_CH_PRD(pwm->hwpwm));
+	sun4i_pwm->next_period[pwm->hwpwm] = jiffies +
+		usecs_to_jiffies(cstate.period / 1000 + 1);
+	sun4i_pwm->needs_delay[pwm->hwpwm] = true;
+
 	if (state->polarity != PWM_POLARITY_NORMAL)
 		ctrl &= ~BIT_CH(PWM_ACT_STATE, pwm->hwpwm);
 	else
 		ctrl |= BIT_CH(PWM_ACT_STATE, pwm->hwpwm);
 
 	ctrl |= BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
+
 	if (state->enabled) {
 		ctrl |= BIT_CH(PWM_EN, pwm->hwpwm);
 	} else if (!sun4i_pwm->needs_delay[pwm->hwpwm]) {
@@ -264,6 +299,7 @@ static int sun4i_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
 		ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
 	}
 
+bypass_mode:
 	sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
 
 	spin_unlock(&sun4i_pwm->ctrl_lock);
-- 
2.20.1

[PATCH v5 6/8] pwm: sun4i: Add support for H6 PWM

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

Now that sun4i PWM driver supports deasserting reset line and enabling
bus clock, support for H6 PWM can be added.

Note that while H6 PWM has two channels, only first one is wired to
output pin. Second channel is used as a clock source to companion AC200
chip which is bundled into same package.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 drivers/pwm/pwm-sun4i.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
index b64250b7e2be..8d6699659db7 100644
--- a/drivers/pwm/pwm-sun4i.c
+++ b/drivers/pwm/pwm-sun4i.c
@@ -358,6 +358,12 @@ static const struct sun4i_pwm_data sun4i_pwm_single_bypass = {
 	.npwm = 1,
 };
 
+static const struct sun4i_pwm_data sun50i_h6_pwm_data = {
+	.has_prescaler_bypass = true,
+	.has_direct_mod_clk_output = true,
+	.npwm = 2,
+};
+
 static const struct of_device_id sun4i_pwm_dt_ids[] = {
 	{
 		.compatible = "allwinner,sun4i-a10-pwm",
@@ -374,6 +380,9 @@ static const struct of_device_id sun4i_pwm_dt_ids[] = {
 	}, {
 		.compatible = "allwinner,sun8i-h3-pwm",
 		.data = &sun4i_pwm_single_bypass,
+	}, {
+		.compatible = "allwinner,sun50i-h6-pwm",
+		.data = &sun50i_h6_pwm_data,
 	}, {
 		/* sentinel */
 	},
-- 
2.20.1

[PATCH v5 7/8] arm64: dts: allwinner: h6: Add PWM node

[Clément Péron]

From: Jernej Skrabec <jernej.skrabec@siol.net>

Allwinner H6 PWM is similar to that in A20 except that it has additional
bus clock and reset line.

Note that first PWM channel is connected to output pin and second
channel is used internally, as a clock source to AC200 co-packaged chip.
This means that any combination of these two channels can be used and
thus it doesn't make sense to add pinctrl nodes at this point.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 29824081b43b..6d4bde488f15 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -245,6 +245,16 @@
 			status = "disabled";
 		};
 
+		pwm: pwm@300a000 {
+			compatible = "allwinner,sun50i-h6-pwm";
+			reg = <0x0300a000 0x400>;
+			clocks = <&osc24M>, <&ccu CLK_BUS_PWM>;
+			clock-names = "mod", "bus";
+			resets = <&ccu RST_BUS_PWM>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		pio: pinctrl@300b000 {
 			compatible = "allwinner,sun50i-h6-pinctrl";
 			reg = <0x0300b000 0x400>;
-- 
2.20.1

[PATCH v5 8/8] [DO NOT MERGE] arm64: allwinner: h6: enable Beelink GS1 PWM

[Clément Péron]

Signed-off-by: Clément Péron <peron.clem@gmail.com>
---
 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
index f335f7482a73..cf684bc7374d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
@@ -136,6 +136,10 @@
 	vcc-pg-supply = <&reg_aldo1>;
 };
 
+&pwm {
+	status = "okay";
+};
+
 &r_i2c {
 	status = "okay";
 
-- 
2.20.1

Re: [PATCH v5 3/8] pwm: sun4i: Prefer "mod" clock to unnamed

[Uwe Kleine-König]

On Mon, Nov 18, 2019 at 10:37:22AM +0100, Clément Péron wrote:
> New device tree bindings called the source clock of the module
> "mod" when several clocks are defined.
> 
> Try to get a clock called "mod" if nothing is found try to get
> an unnamed clock.
> 
> Signed-off-by: Clément Péron <peron.clem@gmail.com>
> ---
>  drivers/pwm/pwm-sun4i.c | 29 +++++++++++++++++++++++++++--
>  1 file changed, 27 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
> index c17935805690..bbb1ed194c0e 100644
> --- a/drivers/pwm/pwm-sun4i.c
> +++ b/drivers/pwm/pwm-sun4i.c
> @@ -362,9 +362,34 @@ static int sun4i_pwm_probe(struct platform_device *pdev)
>  	if (IS_ERR(pwm->base))
>  		return PTR_ERR(pwm->base);
>  
> -	pwm->clk = devm_clk_get(&pdev->dev, NULL);
> -	if (IS_ERR(pwm->clk))
> +	/*
> +	 * All hardware variants need a source clock that is divided and
> +	 * then feeds the counter that defines the output wave form. In the
> +	 * device tree this clock is either unnamed or called "mod".
> +	 * Some variants (e.g. H6) need another clock to access the
> +	 * hardware registers; this is called "bus".
> +	 * So we request "mod" first (and ignore the corner case that a
> +	 * parent provides a "mod" clock while the right one would be the
> +	 * unnamed one of the PWM device) and if this is not found we fall
> +	 * back to the first clock of the PWM.
> +	 */
> +	pwm->clk = devm_clk_get_optional(&pdev->dev, "mod");
> +	if (IS_ERR(pwm->clk)) {
> +		if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
> +			dev_err(&pdev->dev, "get clock failed %pe\n",
> +				pwm->clk);

I think the line break isn't needed here. Unless I'm mistaken the final
; will end in column 80 which is fine.

>  		return PTR_ERR(pwm->clk);
> +	}
> +
> +	if (!pwm->clk) {
> +		pwm->clk = devm_clk_get(&pdev->dev, NULL);
> +		if (IS_ERR(pwm->clk)) {
> +			if (PTR_ERR(pwm->rst) != -EPROBE_DEFER)
> +				dev_err(&pdev->dev, "get clock failed %pe\n",
> +					pwm->clk);

A different error message than above would be nice to be able to
distinguish the two cases.

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

Re: [PATCH v5 4/8] pwm: sun4i: Add an optional probe for bus clock

[Uwe Kleine-König]

On Mon, Nov 18, 2019 at 10:37:23AM +0100, Clément Péron wrote:
> From: Jernej Skrabec <jernej.skrabec@siol.net>
> 
> H6 PWM core needs bus clock to be enabled in order to work.
> 
> Add an optional probe for it and a fallback for previous
> bindings without name on module clock.

This paragraph doesn't belong in this patch's description.

The code changes look fine to me.

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |