[PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[Rasmus Villemoes]

There have been several attempts in the past few years to allow
building the QUICC engine drivers for platforms other than PPC32. This
is yet another attempt.

v5 can be found here: https://lore.kernel.org/lkml/20191118112324.22725-1-linux@rasmusvillemoes.dk/

Changes in v6:

- add various R-b, A-b tags

- add a patch (48/49) fixing a build issue on ARM with CONFIG_SMP=y

I added that patch last in the series, apart from the "allow to build
on ARM" Kconfig change, to preserve the enumeration of the other
patches from v5.

1-5 are about replacing in_be32 etc. in the core QE code (drivers/soc/fsl/qe).

6-8 handle miscellaneous other ppcisms.

9-21 deal with qe_ic: Simplifying the driver significantly by removing
unused code, and removing the platform-specific initialization from
arch/powerpc/.

22-25 deal with raw access to devicetree properties in native endianness.

26-34 makes drivers/tty/serial/ucc_uart.c (CONFIG_SERIAL_QE) ready to build on non-ppc.

35-46 deal with IS_ERR_VALUE() and some other things found while
digging around that part of the code.

47 adds a PPC32 dependency to UCC_GETH - it has some of the same
issues that have been fixed in the ucc_uart and ucc_hdlc cases. Nobody
has requested that I allow that driver to be built for arm{,64} and
reportedly, the hardware has only ever shipped on PPC SOCs. So instead
of growing this series even bigger, I kept that addition. It's trivial
to remove if somebody cares enough to fix the build errors/warnings
and actually has a platform to test the result on.

48 fixes a build issue on ARM reported by the kbuild bot.

Finally patch 49 lifts the PPC32 restriction from QUICC_ENGINE. At the
request of Li Yang, it doesn't remove the PPC32 dependency but instead
changes it to PPC|| ARM || ARM64 (or COMPILE_TEST), i.e. listing
the platforms that may have a QE.

The series has been built and booted on both an mpc8309-based platform
(ppc) as well as an ls1021a-based platform (arm). The core QE code is
exercised on both, while I could only test the ucc_uart on arm, since
the uarts are not wired up on our mpc8309 board. Qiang Zhao reports
that the ucc_hdlc driver does indeed work on a ls1043ardb (arm64)
board.

Rasmus Villemoes (49):
  soc: fsl: qe: remove space-before-tab
  soc: fsl: qe: drop volatile qualifier of struct qe_ic::regs
  soc: fsl: qe: rename qe_(clr/set/clrset)bit* helpers
  soc: fsl: qe: introduce qe_io{read,write}* wrappers
  soc: fsl: qe: avoid ppc-specific io accessors
  soc: fsl: qe: replace spin_event_timeout by readx_poll_timeout_atomic
  soc: fsl: qe: qe.c: guard use of pvr_version_is() with CONFIG_PPC32
  soc: fsl: qe: drop unneeded #includes
  soc: fsl: qe: drop assign-only high_active in qe_ic_init
  soc: fsl: qe: remove pointless sysfs registration in qe_ic.c
  soc: fsl: qe: use qe_ic_cascade_{low,high}_mpic also on 83xx
  soc: fsl: qe: move calls of qe_ic_init out of arch/powerpc/
  powerpc/83xx: remove mpc83xx_ipic_and_qe_init_IRQ
  powerpc/85xx: remove mostly pointless mpc85xx_qe_init()
  soc: fsl: qe: move qe_ic_cascade_* functions to qe_ic.c
  soc: fsl: qe: rename qe_ic_cascade_low_mpic -> qe_ic_cascade_low
  soc: fsl: qe: remove unused qe_ic_set_* functions
  soc: fsl: qe: don't use NO_IRQ in qe_ic.c
  soc: fsl: qe: make qe_ic_get_{low,high}_irq static
  soc: fsl: qe: simplify qe_ic_init()
  soc: fsl: qe: merge qe_ic.h headers into qe_ic.c
  soc: fsl: qe: qe.c: use of_property_read_* helpers
  soc: fsl: qe: qe_io.c: don't open-code of_parse_phandle()
  soc: fsl: qe: qe_io.c: access device tree property using be32_to_cpu
  soc: fsl: qe: qe_io.c: use of_property_read_u32() in par_io_init()
  soc: fsl: move cpm.h from powerpc/include/asm to include/soc/fsl
  soc/fsl/qe/qe.h: update include path for cpm.h
  serial: ucc_uart: explicitly include soc/fsl/cpm.h
  serial: ucc_uart: replace ppc-specific IO accessors
  serial: ucc_uart: factor out soft_uart initialization
  serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
  serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
  serial: ucc_uart: limit brg-frequency workaround to PPC32
  serial: ucc_uart: access __be32 field using be32_to_cpu
  soc: fsl: qe: change return type of cpm_muram_alloc() to s32
  soc: fsl: qe: make cpm_muram_free() return void
  soc: fsl: qe: make cpm_muram_free() ignore a negative offset
  soc: fsl: qe: drop broken lazy call of cpm_muram_init()
  soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error
    path
  soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
  soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
  soc: fsl: qe: drop pointless check in qe_sdma_init()
  soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
  net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
  net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
  net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
  net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
  soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
  soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE

 arch/powerpc/include/asm/cpm.h                | 172 +-------
 arch/powerpc/platforms/83xx/km83xx.c          |   3 +-
 arch/powerpc/platforms/83xx/misc.c            |  23 --
 arch/powerpc/platforms/83xx/mpc832x_mds.c     |   3 +-
 arch/powerpc/platforms/83xx/mpc832x_rdb.c     |   3 +-
 arch/powerpc/platforms/83xx/mpc836x_mds.c     |   3 +-
 arch/powerpc/platforms/83xx/mpc836x_rdk.c     |   3 +-
 arch/powerpc/platforms/83xx/mpc83xx.h         |   7 -
 arch/powerpc/platforms/85xx/common.c          |  23 --
 arch/powerpc/platforms/85xx/corenet_generic.c |  12 -
 arch/powerpc/platforms/85xx/mpc85xx.h         |   2 -
 arch/powerpc/platforms/85xx/mpc85xx_mds.c     |  28 --
 arch/powerpc/platforms/85xx/mpc85xx_rdb.c     |  18 -
 arch/powerpc/platforms/85xx/twr_p102x.c       |  16 -
 drivers/net/ethernet/freescale/Kconfig        |   2 +-
 drivers/net/wan/fsl_ucc_hdlc.c                |  23 +-
 drivers/net/wan/fsl_ucc_hdlc.h                |   2 +-
 drivers/soc/fsl/qe/Kconfig                    |   3 +-
 drivers/soc/fsl/qe/gpio.c                     |  34 +-
 drivers/soc/fsl/qe/qe.c                       | 104 ++---
 drivers/soc/fsl/qe/qe_common.c                |  50 +--
 drivers/soc/fsl/qe/qe_ic.c                    | 285 ++++++-------
 drivers/soc/fsl/qe/qe_ic.h                    |  99 -----
 drivers/soc/fsl/qe/qe_io.c                    |  70 ++--
 drivers/soc/fsl/qe/qe_tdm.c                   |   8 +-
 drivers/soc/fsl/qe/ucc.c                      |  27 +-
 drivers/soc/fsl/qe/ucc_fast.c                 |  86 ++--
 drivers/soc/fsl/qe/ucc_slow.c                 |  60 ++-
 drivers/soc/fsl/qe/usb.c                      |   2 +-
 drivers/tty/serial/ucc_uart.c                 | 385 +++++++++---------
 include/soc/fsl/cpm.h                         | 171 ++++++++
 include/soc/fsl/qe/qe.h                       |  59 ++-
 include/soc/fsl/qe/qe_ic.h                    | 135 ------
 include/soc/fsl/qe/ucc_fast.h                 |   4 +-
 include/soc/fsl/qe/ucc_slow.h                 |   6 +-
 35 files changed, 775 insertions(+), 1156 deletions(-)
 delete mode 100644 drivers/soc/fsl/qe/qe_ic.h
 create mode 100644 include/soc/fsl/cpm.h
 delete mode 100644 include/soc/fsl/qe/qe_ic.h

-- 
2.23.0

[PATCH v6 01/49] soc: fsl: qe: remove space-before-tab

[Rasmus Villemoes]

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index 417df7e19281..2a0e6e642776 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -378,8 +378,8 @@ static int qe_sdma_init(void)
 	}
 
 	out_be32(&sdma->sdebcr, (u32) sdma_buf_offset & QE_SDEBCR_BA_MASK);
- 	out_be32(&sdma->sdmr, (QE_SDMR_GLB_1_MSK |
- 					(0x1 << QE_SDMR_CEN_SHIFT)));
+	out_be32(&sdma->sdmr, (QE_SDMR_GLB_1_MSK |
+		 (0x1 << QE_SDMR_CEN_SHIFT)));
 
 	return 0;
 }
-- 
2.23.0

[PATCH v6 02/49] soc: fsl: qe: drop volatile qualifier of struct qe_ic::regs

[Rasmus Villemoes]

The actual io accessors (e.g. in_be32) implicitly add a volatile
qualifier to their address argument. Remove volatile from the struct
definition and the qe_ic_(read/write) helpers, in preparation for
switching from the ppc-specific io accessors to generic ones.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 4 ++--
 drivers/soc/fsl/qe/qe_ic.h | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 9bac546998d3..791adcd121d1 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -171,12 +171,12 @@ static struct qe_ic_info qe_ic_info[] = {
 		},
 };
 
-static inline u32 qe_ic_read(volatile __be32  __iomem * base, unsigned int reg)
+static inline u32 qe_ic_read(__be32  __iomem *base, unsigned int reg)
 {
 	return in_be32(base + (reg >> 2));
 }
 
-static inline void qe_ic_write(volatile __be32  __iomem * base, unsigned int reg,
+static inline void qe_ic_write(__be32  __iomem *base, unsigned int reg,
 			       u32 value)
 {
 	out_be32(base + (reg >> 2), value);
diff --git a/drivers/soc/fsl/qe/qe_ic.h b/drivers/soc/fsl/qe/qe_ic.h
index 08c695672a03..9420378d9b6b 100644
--- a/drivers/soc/fsl/qe/qe_ic.h
+++ b/drivers/soc/fsl/qe/qe_ic.h
@@ -72,7 +72,7 @@
 
 struct qe_ic {
 	/* Control registers offset */
-	volatile u32 __iomem *regs;
+	u32 __iomem *regs;
 
 	/* The remapper for this QEIC */
 	struct irq_domain *irqhost;
-- 
2.23.0

[PATCH v6 03/49] soc: fsl: qe: rename qe_(clr/set/clrset)bit* helpers

[Rasmus Villemoes]

Make it clear that these operate on big-endian registers (i.e. use the
iowrite*be primitives) before we introduce more uses of them and allow
the QE drivers to be built for platforms other than ppc32.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/net/wan/fsl_ucc_hdlc.c |  4 ++--
 drivers/soc/fsl/qe/ucc.c       | 10 +++++-----
 include/soc/fsl/qe/qe.h        | 18 +++++++++---------
 3 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/drivers/net/wan/fsl_ucc_hdlc.c b/drivers/net/wan/fsl_ucc_hdlc.c
index ca0f3be2b6bf..ce6af7d5380f 100644
--- a/drivers/net/wan/fsl_ucc_hdlc.c
+++ b/drivers/net/wan/fsl_ucc_hdlc.c
@@ -623,8 +623,8 @@ static int ucc_hdlc_poll(struct napi_struct *napi, int budget)
 
 	if (howmany < budget) {
 		napi_complete_done(napi, howmany);
-		qe_setbits32(priv->uccf->p_uccm,
-			     (UCCE_HDLC_RX_EVENTS | UCCE_HDLC_TX_EVENTS) << 16);
+		qe_setbits_be32(priv->uccf->p_uccm,
+				(UCCE_HDLC_RX_EVENTS | UCCE_HDLC_TX_EVENTS) << 16);
 	}
 
 	return howmany;
diff --git a/drivers/soc/fsl/qe/ucc.c b/drivers/soc/fsl/qe/ucc.c
index 024d239ac1e1..ae9f2cf560cb 100644
--- a/drivers/soc/fsl/qe/ucc.c
+++ b/drivers/soc/fsl/qe/ucc.c
@@ -540,8 +540,8 @@ int ucc_set_tdm_rxtx_clk(u32 tdm_num, enum qe_clock clock,
 	cmxs1cr = (tdm_num < 4) ? &qe_mux_reg->cmxsi1cr_l :
 				  &qe_mux_reg->cmxsi1cr_h;
 
-	qe_clrsetbits32(cmxs1cr, QE_CMXUCR_TX_CLK_SRC_MASK << shift,
-			clock_bits << shift);
+	qe_clrsetbits_be32(cmxs1cr, QE_CMXUCR_TX_CLK_SRC_MASK << shift,
+			   clock_bits << shift);
 
 	return 0;
 }
@@ -650,9 +650,9 @@ int ucc_set_tdm_rxtx_sync(u32 tdm_num, enum qe_clock clock,
 
 	shift = ucc_get_tdm_sync_shift(mode, tdm_num);
 
-	qe_clrsetbits32(&qe_mux_reg->cmxsi1syr,
-			QE_CMXUCR_TX_CLK_SRC_MASK << shift,
-			source << shift);
+	qe_clrsetbits_be32(&qe_mux_reg->cmxsi1syr,
+			   QE_CMXUCR_TX_CLK_SRC_MASK << shift,
+			   source << shift);
 
 	return 0;
 }
diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
index c1036d16ed03..a1aa4eb28f0c 100644
--- a/include/soc/fsl/qe/qe.h
+++ b/include/soc/fsl/qe/qe.h
@@ -241,20 +241,20 @@ static inline int qe_alive_during_sleep(void)
 #define qe_muram_offset cpm_muram_offset
 #define qe_muram_dma cpm_muram_dma
 
-#define qe_setbits32(_addr, _v) iowrite32be(ioread32be(_addr) |  (_v), (_addr))
-#define qe_clrbits32(_addr, _v) iowrite32be(ioread32be(_addr) & ~(_v), (_addr))
+#define qe_setbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) |  (_v), (_addr))
+#define qe_clrbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) & ~(_v), (_addr))
 
-#define qe_setbits16(_addr, _v) iowrite16be(ioread16be(_addr) |  (_v), (_addr))
-#define qe_clrbits16(_addr, _v) iowrite16be(ioread16be(_addr) & ~(_v), (_addr))
+#define qe_setbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) |  (_v), (_addr))
+#define qe_clrbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) & ~(_v), (_addr))
 
-#define qe_setbits8(_addr, _v) iowrite8(ioread8(_addr) |  (_v), (_addr))
-#define qe_clrbits8(_addr, _v) iowrite8(ioread8(_addr) & ~(_v), (_addr))
+#define qe_setbits_8(_addr, _v) iowrite8(ioread8(_addr) |  (_v), (_addr))
+#define qe_clrbits_8(_addr, _v) iowrite8(ioread8(_addr) & ~(_v), (_addr))
 
-#define qe_clrsetbits32(addr, clear, set) \
+#define qe_clrsetbits_be32(addr, clear, set) \
 	iowrite32be((ioread32be(addr) & ~(clear)) | (set), (addr))
-#define qe_clrsetbits16(addr, clear, set) \
+#define qe_clrsetbits_be16(addr, clear, set) \
 	iowrite16be((ioread16be(addr) & ~(clear)) | (set), (addr))
-#define qe_clrsetbits8(addr, clear, set) \
+#define qe_clrsetbits_8(addr, clear, set) \
 	iowrite8((ioread8(addr) & ~(clear)) | (set), (addr))
 
 /* Structure that defines QE firmware binary files.
-- 
2.23.0

[PATCH v6 04/49] soc: fsl: qe: introduce qe_io{read,write}* wrappers

[Rasmus Villemoes]

The QUICC engine drivers use the powerpc-specific out_be32() etc. In
order to allow those drivers to build for other architectures, those
must be replaced by iowrite32be(). However, on powerpc, out_be32() is
a simple inline function while iowrite32be() is out-of-line. So in
order not to introduce a performance regression on powerpc when making
the drivers work on other architectures, introduce qe_io* helpers.

Also define the qe_{clr,set,clrset}bits* helpers in terms of these new
macros.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 include/soc/fsl/qe/qe.h | 34 +++++++++++++++++++++++++---------
 1 file changed, 25 insertions(+), 9 deletions(-)

diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
index a1aa4eb28f0c..9cac04c692fd 100644
--- a/include/soc/fsl/qe/qe.h
+++ b/include/soc/fsl/qe/qe.h
@@ -241,21 +241,37 @@ static inline int qe_alive_during_sleep(void)
 #define qe_muram_offset cpm_muram_offset
 #define qe_muram_dma cpm_muram_dma
 
-#define qe_setbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) |  (_v), (_addr))
-#define qe_clrbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) & ~(_v), (_addr))
+#ifdef CONFIG_PPC32
+#define qe_iowrite8(val, addr)     out_8(addr, val)
+#define qe_iowrite16be(val, addr)  out_be16(addr, val)
+#define qe_iowrite32be(val, addr)  out_be32(addr, val)
+#define qe_ioread8(addr)           in_8(addr)
+#define qe_ioread16be(addr)        in_be16(addr)
+#define qe_ioread32be(addr)        in_be32(addr)
+#else
+#define qe_iowrite8(val, addr)     iowrite8(val, addr)
+#define qe_iowrite16be(val, addr)  iowrite16be(val, addr)
+#define qe_iowrite32be(val, addr)  iowrite32be(val, addr)
+#define qe_ioread8(addr)           ioread8(addr)
+#define qe_ioread16be(addr)        ioread16be(addr)
+#define qe_ioread32be(addr)        ioread32be(addr)
+#endif
+
+#define qe_setbits_be32(_addr, _v) qe_iowrite32be(qe_ioread32be(_addr) |  (_v), (_addr))
+#define qe_clrbits_be32(_addr, _v) qe_iowrite32be(qe_ioread32be(_addr) & ~(_v), (_addr))
 
-#define qe_setbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) |  (_v), (_addr))
-#define qe_clrbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) & ~(_v), (_addr))
+#define qe_setbits_be16(_addr, _v) qe_iowrite16be(qe_ioread16be(_addr) |  (_v), (_addr))
+#define qe_clrbits_be16(_addr, _v) qe_iowrite16be(qe_ioread16be(_addr) & ~(_v), (_addr))
 
-#define qe_setbits_8(_addr, _v) iowrite8(ioread8(_addr) |  (_v), (_addr))
-#define qe_clrbits_8(_addr, _v) iowrite8(ioread8(_addr) & ~(_v), (_addr))
+#define qe_setbits_8(_addr, _v) qe_iowrite8(qe_ioread8(_addr) |  (_v), (_addr))
+#define qe_clrbits_8(_addr, _v) qe_iowrite8(qe_ioread8(_addr) & ~(_v), (_addr))
 
 #define qe_clrsetbits_be32(addr, clear, set) \
-	iowrite32be((ioread32be(addr) & ~(clear)) | (set), (addr))
+	qe_iowrite32be((qe_ioread32be(addr) & ~(clear)) | (set), (addr))
 #define qe_clrsetbits_be16(addr, clear, set) \
-	iowrite16be((ioread16be(addr) & ~(clear)) | (set), (addr))
+	qe_iowrite16be((qe_ioread16be(addr) & ~(clear)) | (set), (addr))
 #define qe_clrsetbits_8(addr, clear, set) \
-	iowrite8((ioread8(addr) & ~(clear)) | (set), (addr))
+	qe_iowrite8((qe_ioread8(addr) & ~(clear)) | (set), (addr))
 
 /* Structure that defines QE firmware binary files.
  *
-- 
2.23.0

Re: [PATCH v6 04/49] soc: fsl: qe: introduce qe_io{read,write}* wrappers

[Christophe Leroy]

Hi Rasmus,

Le 28/11/2019 à 15:55, Rasmus Villemoes a écrit :
> The QUICC engine drivers use the powerpc-specific out_be32() etc. In
> order to allow those drivers to build for other architectures, those
> must be replaced by iowrite32be(). However, on powerpc, out_be32() is
> a simple inline function while iowrite32be() is out-of-line. So in
> order not to introduce a performance regression on powerpc when making
> the drivers work on other architectures, introduce qe_io* helpers.
> 
> Also define the qe_{clr,set,clrset}bits* helpers in terms of these new
> macros.

Since commit https://github.com/linuxppc/linux/commit/894fa235eb4ca0bfa692dbe4932c2f940cdc8c1e 
ioread/iowrite wrappers are also inlined on PPC32, so this commit can now be reverted.

Christophe

> 
> Reviewed-by: Timur Tabi <timur@kernel.org>
> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
> ---
>   include/soc/fsl/qe/qe.h | 34 +++++++++++++++++++++++++---------
>   1 file changed, 25 insertions(+), 9 deletions(-)
> 
> diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
> index a1aa4eb28f0c..9cac04c692fd 100644
> --- a/include/soc/fsl/qe/qe.h
> +++ b/include/soc/fsl/qe/qe.h
> @@ -241,21 +241,37 @@ static inline int qe_alive_during_sleep(void)
>   #define qe_muram_offset cpm_muram_offset
>   #define qe_muram_dma cpm_muram_dma
>   
> -#define qe_setbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) |  (_v), (_addr))
> -#define qe_clrbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) & ~(_v), (_addr))
> +#ifdef CONFIG_PPC32
> +#define qe_iowrite8(val, addr)     out_8(addr, val)
> +#define qe_iowrite16be(val, addr)  out_be16(addr, val)
> +#define qe_iowrite32be(val, addr)  out_be32(addr, val)
> +#define qe_ioread8(addr)           in_8(addr)
> +#define qe_ioread16be(addr)        in_be16(addr)
> +#define qe_ioread32be(addr)        in_be32(addr)
> +#else
> +#define qe_iowrite8(val, addr)     iowrite8(val, addr)
> +#define qe_iowrite16be(val, addr)  iowrite16be(val, addr)
> +#define qe_iowrite32be(val, addr)  iowrite32be(val, addr)
> +#define qe_ioread8(addr)           ioread8(addr)
> +#define qe_ioread16be(addr)        ioread16be(addr)
> +#define qe_ioread32be(addr)        ioread32be(addr)
> +#endif
> +
> +#define qe_setbits_be32(_addr, _v) qe_iowrite32be(qe_ioread32be(_addr) |  (_v), (_addr))
> +#define qe_clrbits_be32(_addr, _v) qe_iowrite32be(qe_ioread32be(_addr) & ~(_v), (_addr))
>   
> -#define qe_setbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) |  (_v), (_addr))
> -#define qe_clrbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) & ~(_v), (_addr))
> +#define qe_setbits_be16(_addr, _v) qe_iowrite16be(qe_ioread16be(_addr) |  (_v), (_addr))
> +#define qe_clrbits_be16(_addr, _v) qe_iowrite16be(qe_ioread16be(_addr) & ~(_v), (_addr))
>   
> -#define qe_setbits_8(_addr, _v) iowrite8(ioread8(_addr) |  (_v), (_addr))
> -#define qe_clrbits_8(_addr, _v) iowrite8(ioread8(_addr) & ~(_v), (_addr))
> +#define qe_setbits_8(_addr, _v) qe_iowrite8(qe_ioread8(_addr) |  (_v), (_addr))
> +#define qe_clrbits_8(_addr, _v) qe_iowrite8(qe_ioread8(_addr) & ~(_v), (_addr))
>   
>   #define qe_clrsetbits_be32(addr, clear, set) \
> -	iowrite32be((ioread32be(addr) & ~(clear)) | (set), (addr))
> +	qe_iowrite32be((qe_ioread32be(addr) & ~(clear)) | (set), (addr))
>   #define qe_clrsetbits_be16(addr, clear, set) \
> -	iowrite16be((ioread16be(addr) & ~(clear)) | (set), (addr))
> +	qe_iowrite16be((qe_ioread16be(addr) & ~(clear)) | (set), (addr))
>   #define qe_clrsetbits_8(addr, clear, set) \
> -	iowrite8((ioread8(addr) & ~(clear)) | (set), (addr))
> +	qe_iowrite8((qe_ioread8(addr) & ~(clear)) | (set), (addr))
>   
>   /* Structure that defines QE firmware binary files.
>    *
> 

Re: [PATCH v6 04/49] soc: fsl: qe: introduce qe_io{read,write}* wrappers

[Li Yang]

On Tue, Jan 19, 2021 at 11:35 AM Christophe Leroy
<christophe.leroy@csgroup.eu> wrote:
>
> Hi Rasmus,
>
> Le 28/11/2019 à 15:55, Rasmus Villemoes a écrit :
> > The QUICC engine drivers use the powerpc-specific out_be32() etc. In
> > order to allow those drivers to build for other architectures, those
> > must be replaced by iowrite32be(). However, on powerpc, out_be32() is
> > a simple inline function while iowrite32be() is out-of-line. So in
> > order not to introduce a performance regression on powerpc when making
> > the drivers work on other architectures, introduce qe_io* helpers.
> >
> > Also define the qe_{clr,set,clrset}bits* helpers in terms of these new
> > macros.
>
> Since commit https://github.com/linuxppc/linux/commit/894fa235eb4ca0bfa692dbe4932c2f940cdc8c1e
> ioread/iowrite wrappers are also inlined on PPC32, so this commit can now be reverted.

Yes.  That will be great.

>
> Christophe
>
> >
> > Reviewed-by: Timur Tabi <timur@kernel.org>
> > Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
> > ---
> >   include/soc/fsl/qe/qe.h | 34 +++++++++++++++++++++++++---------
> >   1 file changed, 25 insertions(+), 9 deletions(-)
> >
> > diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
> > index a1aa4eb28f0c..9cac04c692fd 100644
> > --- a/include/soc/fsl/qe/qe.h
> > +++ b/include/soc/fsl/qe/qe.h
> > @@ -241,21 +241,37 @@ static inline int qe_alive_during_sleep(void)
> >   #define qe_muram_offset cpm_muram_offset
> >   #define qe_muram_dma cpm_muram_dma
> >
> > -#define qe_setbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) |  (_v), (_addr))
> > -#define qe_clrbits_be32(_addr, _v) iowrite32be(ioread32be(_addr) & ~(_v), (_addr))
> > +#ifdef CONFIG_PPC32
> > +#define qe_iowrite8(val, addr)     out_8(addr, val)
> > +#define qe_iowrite16be(val, addr)  out_be16(addr, val)
> > +#define qe_iowrite32be(val, addr)  out_be32(addr, val)
> > +#define qe_ioread8(addr)           in_8(addr)
> > +#define qe_ioread16be(addr)        in_be16(addr)
> > +#define qe_ioread32be(addr)        in_be32(addr)
> > +#else
> > +#define qe_iowrite8(val, addr)     iowrite8(val, addr)
> > +#define qe_iowrite16be(val, addr)  iowrite16be(val, addr)
> > +#define qe_iowrite32be(val, addr)  iowrite32be(val, addr)
> > +#define qe_ioread8(addr)           ioread8(addr)
> > +#define qe_ioread16be(addr)        ioread16be(addr)
> > +#define qe_ioread32be(addr)        ioread32be(addr)
> > +#endif
> > +
> > +#define qe_setbits_be32(_addr, _v) qe_iowrite32be(qe_ioread32be(_addr) |  (_v), (_addr))
> > +#define qe_clrbits_be32(_addr, _v) qe_iowrite32be(qe_ioread32be(_addr) & ~(_v), (_addr))
> >
> > -#define qe_setbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) |  (_v), (_addr))
> > -#define qe_clrbits_be16(_addr, _v) iowrite16be(ioread16be(_addr) & ~(_v), (_addr))
> > +#define qe_setbits_be16(_addr, _v) qe_iowrite16be(qe_ioread16be(_addr) |  (_v), (_addr))
> > +#define qe_clrbits_be16(_addr, _v) qe_iowrite16be(qe_ioread16be(_addr) & ~(_v), (_addr))
> >
> > -#define qe_setbits_8(_addr, _v) iowrite8(ioread8(_addr) |  (_v), (_addr))
> > -#define qe_clrbits_8(_addr, _v) iowrite8(ioread8(_addr) & ~(_v), (_addr))
> > +#define qe_setbits_8(_addr, _v) qe_iowrite8(qe_ioread8(_addr) |  (_v), (_addr))
> > +#define qe_clrbits_8(_addr, _v) qe_iowrite8(qe_ioread8(_addr) & ~(_v), (_addr))
> >
> >   #define qe_clrsetbits_be32(addr, clear, set) \
> > -     iowrite32be((ioread32be(addr) & ~(clear)) | (set), (addr))
> > +     qe_iowrite32be((qe_ioread32be(addr) & ~(clear)) | (set), (addr))
> >   #define qe_clrsetbits_be16(addr, clear, set) \
> > -     iowrite16be((ioread16be(addr) & ~(clear)) | (set), (addr))
> > +     qe_iowrite16be((qe_ioread16be(addr) & ~(clear)) | (set), (addr))
> >   #define qe_clrsetbits_8(addr, clear, set) \
> > -     iowrite8((ioread8(addr) & ~(clear)) | (set), (addr))
> > +     qe_iowrite8((qe_ioread8(addr) & ~(clear)) | (set), (addr))
> >
> >   /* Structure that defines QE firmware binary files.
> >    *
> >

[PATCH v6 05/49] soc: fsl: qe: avoid ppc-specific io accessors

[Rasmus Villemoes]

In preparation for allowing to build QE support for architectures
other than PPC, replace the ppc-specific io accessors by the qe_io*
macros. Done via

$ spatch --sp-file io.cocci --in-place drivers/soc/fsl/qe/

where io.cocci is

@@
expression addr, val;
@@
- out_be32(addr, val)
+ qe_iowrite32be(val, addr)

@@
expression addr;
@@
- in_be32(addr)
+ qe_ioread32be(addr)

@@
expression addr, val;
@@
- out_be16(addr, val)
+ qe_iowrite16be(val, addr)

@@
expression addr;
@@
- in_be16(addr)
+ qe_ioread16be(addr)

@@
expression addr, val;
@@
- out_8(addr, val)
+ qe_iowrite8(val, addr)

@@
expression addr;
@@
- in_8(addr)
+ qe_ioread8(addr)

@@
expression addr, clr, set;
@@
- clrsetbits_be32(addr, clr, set)
+ qe_clrsetbits_be32(addr, clr, set)

@@
expression addr, clr, set;
@@
- clrsetbits_be16(addr, clr, set)
+ qe_clrsetbits_be16(addr, clr, set)

@@
expression addr, clr, set;
@@
- clrsetbits_8(addr, clr, set)
+ qe_clrsetbits_8(addr, clr, set)

@@
expression addr, set;
@@
- setbits32(addr, set)
+ qe_setbits_be32(addr, set)

@@
expression addr, set;
@@
- setbits16(addr, set)
+ qe_setbits_be16(addr, set)

@@
expression addr, set;
@@
- setbits8(addr, set)
+ qe_setbits_8(addr, set)

@@
expression addr, clr;
@@
- clrbits32(addr, clr)
+ qe_clrbits_be32(addr, clr)

@@
expression addr, clr;
@@
- clrbits16(addr, clr)
+ qe_clrbits_be16(addr, clr)

@@
expression addr, clr;
@@
- clrbits8(addr, clr)
+ qe_clrbits_8(addr, clr)

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/gpio.c     | 34 +++++++++--------
 drivers/soc/fsl/qe/qe.c       | 38 ++++++++++---------
 drivers/soc/fsl/qe/qe_ic.c    |  5 ++-
 drivers/soc/fsl/qe/qe_io.c    | 40 +++++++++-----------
 drivers/soc/fsl/qe/qe_tdm.c   |  8 ++--
 drivers/soc/fsl/qe/ucc.c      | 16 ++++----
 drivers/soc/fsl/qe/ucc_fast.c | 71 ++++++++++++++++++-----------------
 drivers/soc/fsl/qe/ucc_slow.c | 38 +++++++++----------
 drivers/soc/fsl/qe/usb.c      |  2 +-
 9 files changed, 129 insertions(+), 123 deletions(-)

diff --git a/drivers/soc/fsl/qe/gpio.c b/drivers/soc/fsl/qe/gpio.c
index f0c29ed8f0ff..12bdfd9cbe7c 100644
--- a/drivers/soc/fsl/qe/gpio.c
+++ b/drivers/soc/fsl/qe/gpio.c
@@ -41,13 +41,13 @@ static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 		container_of(mm_gc, struct qe_gpio_chip, mm_gc);
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 
-	qe_gc->cpdata = in_be32(&regs->cpdata);
+	qe_gc->cpdata = qe_ioread32be(&regs->cpdata);
 	qe_gc->saved_regs.cpdata = qe_gc->cpdata;
-	qe_gc->saved_regs.cpdir1 = in_be32(&regs->cpdir1);
-	qe_gc->saved_regs.cpdir2 = in_be32(&regs->cpdir2);
-	qe_gc->saved_regs.cppar1 = in_be32(&regs->cppar1);
-	qe_gc->saved_regs.cppar2 = in_be32(&regs->cppar2);
-	qe_gc->saved_regs.cpodr = in_be32(&regs->cpodr);
+	qe_gc->saved_regs.cpdir1 = qe_ioread32be(&regs->cpdir1);
+	qe_gc->saved_regs.cpdir2 = qe_ioread32be(&regs->cpdir2);
+	qe_gc->saved_regs.cppar1 = qe_ioread32be(&regs->cppar1);
+	qe_gc->saved_regs.cppar2 = qe_ioread32be(&regs->cppar2);
+	qe_gc->saved_regs.cpodr = qe_ioread32be(&regs->cpodr);
 }
 
 static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
@@ -56,7 +56,7 @@ static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 	u32 pin_mask = 1 << (QE_PIO_PINS - 1 - gpio);
 
-	return !!(in_be32(&regs->cpdata) & pin_mask);
+	return !!(qe_ioread32be(&regs->cpdata) & pin_mask);
 }
 
 static void qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
@@ -74,7 +74,7 @@ static void qe_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
 	else
 		qe_gc->cpdata &= ~pin_mask;
 
-	out_be32(&regs->cpdata, qe_gc->cpdata);
+	qe_iowrite32be(qe_gc->cpdata, &regs->cpdata);
 
 	spin_unlock_irqrestore(&qe_gc->lock, flags);
 }
@@ -101,7 +101,7 @@ static void qe_gpio_set_multiple(struct gpio_chip *gc,
 		}
 	}
 
-	out_be32(&regs->cpdata, qe_gc->cpdata);
+	qe_iowrite32be(qe_gc->cpdata, &regs->cpdata);
 
 	spin_unlock_irqrestore(&qe_gc->lock, flags);
 }
@@ -255,11 +255,15 @@ void qe_pin_set_dedicated(struct qe_pin *qe_pin)
 	spin_lock_irqsave(&qe_gc->lock, flags);
 
 	if (second_reg) {
-		clrsetbits_be32(&regs->cpdir2, mask2, sregs->cpdir2 & mask2);
-		clrsetbits_be32(&regs->cppar2, mask2, sregs->cppar2 & mask2);
+		qe_clrsetbits_be32(&regs->cpdir2, mask2,
+				   sregs->cpdir2 & mask2);
+		qe_clrsetbits_be32(&regs->cppar2, mask2,
+				   sregs->cppar2 & mask2);
 	} else {
-		clrsetbits_be32(&regs->cpdir1, mask2, sregs->cpdir1 & mask2);
-		clrsetbits_be32(&regs->cppar1, mask2, sregs->cppar1 & mask2);
+		qe_clrsetbits_be32(&regs->cpdir1, mask2,
+				   sregs->cpdir1 & mask2);
+		qe_clrsetbits_be32(&regs->cppar1, mask2,
+				   sregs->cppar1 & mask2);
 	}
 
 	if (sregs->cpdata & mask1)
@@ -267,8 +271,8 @@ void qe_pin_set_dedicated(struct qe_pin *qe_pin)
 	else
 		qe_gc->cpdata &= ~mask1;
 
-	out_be32(&regs->cpdata, qe_gc->cpdata);
-	clrsetbits_be32(&regs->cpodr, mask1, sregs->cpodr & mask1);
+	qe_iowrite32be(qe_gc->cpdata, &regs->cpdata);
+	qe_clrsetbits_be32(&regs->cpodr, mask1, sregs->cpodr & mask1);
 
 	spin_unlock_irqrestore(&qe_gc->lock, flags);
 }
diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index 2a0e6e642776..456bd7416876 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -112,7 +112,7 @@ int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input)
 
 	spin_lock_irqsave(&qe_lock, flags);
 	if (cmd == QE_RESET) {
-		out_be32(&qe_immr->cp.cecr, (u32) (cmd | QE_CR_FLG));
+		qe_iowrite32be((u32)(cmd | QE_CR_FLG), &qe_immr->cp.cecr);
 	} else {
 		if (cmd == QE_ASSIGN_PAGE) {
 			/* Here device is the SNUM, not sub-block */
@@ -129,15 +129,14 @@ int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input)
 				mcn_shift = QE_CR_MCN_NORMAL_SHIFT;
 		}
 
-		out_be32(&qe_immr->cp.cecdr, cmd_input);
-		out_be32(&qe_immr->cp.cecr,
-			 (cmd | QE_CR_FLG | ((u32) device << dev_shift) | (u32)
-			  mcn_protocol << mcn_shift));
+		qe_iowrite32be(cmd_input, &qe_immr->cp.cecdr);
+		qe_iowrite32be((cmd | QE_CR_FLG | ((u32)device << dev_shift) | (u32)mcn_protocol << mcn_shift),
+			       &qe_immr->cp.cecr);
 	}
 
 	/* wait for the QE_CR_FLG to clear */
-	ret = spin_event_timeout((in_be32(&qe_immr->cp.cecr) & QE_CR_FLG) == 0,
-			   100, 0);
+	ret = spin_event_timeout((qe_ioread32be(&qe_immr->cp.cecr) & QE_CR_FLG) == 0,
+				 100, 0);
 	/* On timeout (e.g. failure), the expression will be false (ret == 0),
 	   otherwise it will be true (ret == 1). */
 	spin_unlock_irqrestore(&qe_lock, flags);
@@ -230,7 +229,7 @@ int qe_setbrg(enum qe_clock brg, unsigned int rate, unsigned int multiplier)
 	tempval = ((divisor - 1) << QE_BRGC_DIVISOR_SHIFT) |
 		QE_BRGC_ENABLE | div16;
 
-	out_be32(&qe_immr->brg.brgc[brg - QE_BRG1], tempval);
+	qe_iowrite32be(tempval, &qe_immr->brg.brgc[brg - QE_BRG1]);
 
 	return 0;
 }
@@ -377,9 +376,10 @@ static int qe_sdma_init(void)
 			return -ENOMEM;
 	}
 
-	out_be32(&sdma->sdebcr, (u32) sdma_buf_offset & QE_SDEBCR_BA_MASK);
-	out_be32(&sdma->sdmr, (QE_SDMR_GLB_1_MSK |
-		 (0x1 << QE_SDMR_CEN_SHIFT)));
+	qe_iowrite32be((u32)sdma_buf_offset & QE_SDEBCR_BA_MASK,
+		       &sdma->sdebcr);
+	qe_iowrite32be((QE_SDMR_GLB_1_MSK | (0x1 << QE_SDMR_CEN_SHIFT)),
+		       &sdma->sdmr);
 
 	return 0;
 }
@@ -417,14 +417,14 @@ static void qe_upload_microcode(const void *base,
 			"uploading microcode '%s'\n", ucode->id);
 
 	/* Use auto-increment */
-	out_be32(&qe_immr->iram.iadd, be32_to_cpu(ucode->iram_offset) |
-		QE_IRAM_IADD_AIE | QE_IRAM_IADD_BADDR);
+	qe_iowrite32be(be32_to_cpu(ucode->iram_offset) | QE_IRAM_IADD_AIE | QE_IRAM_IADD_BADDR,
+		       &qe_immr->iram.iadd);
 
 	for (i = 0; i < be32_to_cpu(ucode->count); i++)
-		out_be32(&qe_immr->iram.idata, be32_to_cpu(code[i]));
+		qe_iowrite32be(be32_to_cpu(code[i]), &qe_immr->iram.idata);
 	
 	/* Set I-RAM Ready Register */
-	out_be32(&qe_immr->iram.iready, be32_to_cpu(QE_IRAM_READY));
+	qe_iowrite32be(be32_to_cpu(QE_IRAM_READY), &qe_immr->iram.iready);
 }
 
 /*
@@ -509,7 +509,7 @@ int qe_upload_firmware(const struct qe_firmware *firmware)
 	 * If the microcode calls for it, split the I-RAM.
 	 */
 	if (!firmware->split)
-		setbits16(&qe_immr->cp.cercr, QE_CP_CERCR_CIR);
+		qe_setbits_be16(&qe_immr->cp.cercr, QE_CP_CERCR_CIR);
 
 	if (firmware->soc.model)
 		printk(KERN_INFO
@@ -543,11 +543,13 @@ int qe_upload_firmware(const struct qe_firmware *firmware)
 			u32 trap = be32_to_cpu(ucode->traps[j]);
 
 			if (trap)
-				out_be32(&qe_immr->rsp[i].tibcr[j], trap);
+				qe_iowrite32be(trap,
+					       &qe_immr->rsp[i].tibcr[j]);
 		}
 
 		/* Enable traps */
-		out_be32(&qe_immr->rsp[i].eccr, be32_to_cpu(ucode->eccr));
+		qe_iowrite32be(be32_to_cpu(ucode->eccr),
+			       &qe_immr->rsp[i].eccr);
 	}
 
 	qe_firmware_uploaded = 1;
diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 791adcd121d1..8c874372416b 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -24,6 +24,7 @@
 #include <linux/spinlock.h>
 #include <asm/irq.h>
 #include <asm/io.h>
+#include <soc/fsl/qe/qe.h>
 #include <soc/fsl/qe/qe_ic.h>
 
 #include "qe_ic.h"
@@ -173,13 +174,13 @@ static struct qe_ic_info qe_ic_info[] = {
 
 static inline u32 qe_ic_read(__be32  __iomem *base, unsigned int reg)
 {
-	return in_be32(base + (reg >> 2));
+	return qe_ioread32be(base + (reg >> 2));
 }
 
 static inline void qe_ic_write(__be32  __iomem *base, unsigned int reg,
 			       u32 value)
 {
-	out_be32(base + (reg >> 2), value);
+	qe_iowrite32be(value, base + (reg >> 2));
 }
 
 static inline struct qe_ic *qe_ic_from_irq(unsigned int virq)
diff --git a/drivers/soc/fsl/qe/qe_io.c b/drivers/soc/fsl/qe/qe_io.c
index 3657e296a8a2..5e3471ac09dd 100644
--- a/drivers/soc/fsl/qe/qe_io.c
+++ b/drivers/soc/fsl/qe/qe_io.c
@@ -57,16 +57,16 @@ void __par_io_config_pin(struct qe_pio_regs __iomem *par_io, u8 pin, int dir,
 	pin_mask1bit = (u32) (1 << (QE_PIO_PINS - (pin + 1)));
 
 	/* Set open drain, if required */
-	tmp_val = in_be32(&par_io->cpodr);
+	tmp_val = qe_ioread32be(&par_io->cpodr);
 	if (open_drain)
-		out_be32(&par_io->cpodr, pin_mask1bit | tmp_val);
+		qe_iowrite32be(pin_mask1bit | tmp_val, &par_io->cpodr);
 	else
-		out_be32(&par_io->cpodr, ~pin_mask1bit & tmp_val);
+		qe_iowrite32be(~pin_mask1bit & tmp_val, &par_io->cpodr);
 
 	/* define direction */
 	tmp_val = (pin > (QE_PIO_PINS / 2) - 1) ?
-		in_be32(&par_io->cpdir2) :
-		in_be32(&par_io->cpdir1);
+		qe_ioread32be(&par_io->cpdir2) :
+		qe_ioread32be(&par_io->cpdir1);
 
 	/* get all bits mask for 2 bit per port */
 	pin_mask2bits = (u32) (0x3 << (QE_PIO_PINS -
@@ -78,34 +78,30 @@ void __par_io_config_pin(struct qe_pio_regs __iomem *par_io, u8 pin, int dir,
 
 	/* clear and set 2 bits mask */
 	if (pin > (QE_PIO_PINS / 2) - 1) {
-		out_be32(&par_io->cpdir2,
-			 ~pin_mask2bits & tmp_val);
+		qe_iowrite32be(~pin_mask2bits & tmp_val, &par_io->cpdir2);
 		tmp_val &= ~pin_mask2bits;
-		out_be32(&par_io->cpdir2, new_mask2bits | tmp_val);
+		qe_iowrite32be(new_mask2bits | tmp_val, &par_io->cpdir2);
 	} else {
-		out_be32(&par_io->cpdir1,
-			 ~pin_mask2bits & tmp_val);
+		qe_iowrite32be(~pin_mask2bits & tmp_val, &par_io->cpdir1);
 		tmp_val &= ~pin_mask2bits;
-		out_be32(&par_io->cpdir1, new_mask2bits | tmp_val);
+		qe_iowrite32be(new_mask2bits | tmp_val, &par_io->cpdir1);
 	}
 	/* define pin assignment */
 	tmp_val = (pin > (QE_PIO_PINS / 2) - 1) ?
-		in_be32(&par_io->cppar2) :
-		in_be32(&par_io->cppar1);
+		qe_ioread32be(&par_io->cppar2) :
+		qe_ioread32be(&par_io->cppar1);
 
 	new_mask2bits = (u32) (assignment << (QE_PIO_PINS -
 			(pin % (QE_PIO_PINS / 2) + 1) * 2));
 	/* clear and set 2 bits mask */
 	if (pin > (QE_PIO_PINS / 2) - 1) {
-		out_be32(&par_io->cppar2,
-			 ~pin_mask2bits & tmp_val);
+		qe_iowrite32be(~pin_mask2bits & tmp_val, &par_io->cppar2);
 		tmp_val &= ~pin_mask2bits;
-		out_be32(&par_io->cppar2, new_mask2bits | tmp_val);
+		qe_iowrite32be(new_mask2bits | tmp_val, &par_io->cppar2);
 	} else {
-		out_be32(&par_io->cppar1,
-			 ~pin_mask2bits & tmp_val);
+		qe_iowrite32be(~pin_mask2bits & tmp_val, &par_io->cppar1);
 		tmp_val &= ~pin_mask2bits;
-		out_be32(&par_io->cppar1, new_mask2bits | tmp_val);
+		qe_iowrite32be(new_mask2bits | tmp_val, &par_io->cppar1);
 	}
 }
 EXPORT_SYMBOL(__par_io_config_pin);
@@ -133,12 +129,12 @@ int par_io_data_set(u8 port, u8 pin, u8 val)
 	/* calculate pin location */
 	pin_mask = (u32) (1 << (QE_PIO_PINS - 1 - pin));
 
-	tmp_val = in_be32(&par_io[port].cpdata);
+	tmp_val = qe_ioread32be(&par_io[port].cpdata);
 
 	if (val == 0)		/* clear */
-		out_be32(&par_io[port].cpdata, ~pin_mask & tmp_val);
+		qe_iowrite32be(~pin_mask & tmp_val, &par_io[port].cpdata);
 	else			/* set */
-		out_be32(&par_io[port].cpdata, pin_mask | tmp_val);
+		qe_iowrite32be(pin_mask | tmp_val, &par_io[port].cpdata);
 
 	return 0;
 }
diff --git a/drivers/soc/fsl/qe/qe_tdm.c b/drivers/soc/fsl/qe/qe_tdm.c
index e37ebc3be661..7d7d78d3ee50 100644
--- a/drivers/soc/fsl/qe/qe_tdm.c
+++ b/drivers/soc/fsl/qe/qe_tdm.c
@@ -169,10 +169,10 @@ void ucc_tdm_init(struct ucc_tdm *utdm, struct ucc_tdm_info *ut_info)
 				    &siram[siram_entry_id * 32 + 0x200 +  i]);
 	}
 
-	setbits16(&siram[(siram_entry_id * 32) + (utdm->num_of_ts - 1)],
-		  SIR_LAST);
-	setbits16(&siram[(siram_entry_id * 32) + 0x200 + (utdm->num_of_ts - 1)],
-		  SIR_LAST);
+	qe_setbits_be16(&siram[(siram_entry_id * 32) + (utdm->num_of_ts - 1)],
+			SIR_LAST);
+	qe_setbits_be16(&siram[(siram_entry_id * 32) + 0x200 + (utdm->num_of_ts - 1)],
+			SIR_LAST);
 
 	/* Set SIxMR register */
 	sixmr = SIMR_SAD(siram_entry_id);
diff --git a/drivers/soc/fsl/qe/ucc.c b/drivers/soc/fsl/qe/ucc.c
index ae9f2cf560cb..da3d7e2dd837 100644
--- a/drivers/soc/fsl/qe/ucc.c
+++ b/drivers/soc/fsl/qe/ucc.c
@@ -35,8 +35,8 @@ int ucc_set_qe_mux_mii_mng(unsigned int ucc_num)
 		return -EINVAL;
 
 	spin_lock_irqsave(&cmxgcr_lock, flags);
-	clrsetbits_be32(&qe_immr->qmx.cmxgcr, QE_CMXGCR_MII_ENET_MNG,
-		ucc_num << QE_CMXGCR_MII_ENET_MNG_SHIFT);
+	qe_clrsetbits_be32(&qe_immr->qmx.cmxgcr, QE_CMXGCR_MII_ENET_MNG,
+			   ucc_num << QE_CMXGCR_MII_ENET_MNG_SHIFT);
 	spin_unlock_irqrestore(&cmxgcr_lock, flags);
 
 	return 0;
@@ -80,8 +80,8 @@ int ucc_set_type(unsigned int ucc_num, enum ucc_speed_type speed)
 		return -EINVAL;
 	}
 
-	clrsetbits_8(guemr, UCC_GUEMR_MODE_MASK,
-		UCC_GUEMR_SET_RESERVED3 | speed);
+	qe_clrsetbits_8(guemr, UCC_GUEMR_MODE_MASK,
+			UCC_GUEMR_SET_RESERVED3 | speed);
 
 	return 0;
 }
@@ -109,9 +109,9 @@ int ucc_mux_set_grant_tsa_bkpt(unsigned int ucc_num, int set, u32 mask)
 	get_cmxucr_reg(ucc_num, &cmxucr, &reg_num, &shift);
 
 	if (set)
-		setbits32(cmxucr, mask << shift);
+		qe_setbits_be32(cmxucr, mask << shift);
 	else
-		clrbits32(cmxucr, mask << shift);
+		qe_clrbits_be32(cmxucr, mask << shift);
 
 	return 0;
 }
@@ -207,8 +207,8 @@ int ucc_set_qe_mux_rxtx(unsigned int ucc_num, enum qe_clock clock,
 	if (mode == COMM_DIR_RX)
 		shift += 4;
 
-	clrsetbits_be32(cmxucr, QE_CMXUCR_TX_CLK_SRC_MASK << shift,
-		clock_bits << shift);
+	qe_clrsetbits_be32(cmxucr, QE_CMXUCR_TX_CLK_SRC_MASK << shift,
+			   clock_bits << shift);
 
 	return 0;
 }
diff --git a/drivers/soc/fsl/qe/ucc_fast.c b/drivers/soc/fsl/qe/ucc_fast.c
index af4d80e38521..ca0452497a20 100644
--- a/drivers/soc/fsl/qe/ucc_fast.c
+++ b/drivers/soc/fsl/qe/ucc_fast.c
@@ -29,41 +29,42 @@ void ucc_fast_dump_regs(struct ucc_fast_private * uccf)
 	printk(KERN_INFO "Base address: 0x%p\n", uccf->uf_regs);
 
 	printk(KERN_INFO "gumr  : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->gumr, in_be32(&uccf->uf_regs->gumr));
+		  &uccf->uf_regs->gumr, qe_ioread32be(&uccf->uf_regs->gumr));
 	printk(KERN_INFO "upsmr : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->upsmr, in_be32(&uccf->uf_regs->upsmr));
+		  &uccf->uf_regs->upsmr, qe_ioread32be(&uccf->uf_regs->upsmr));
 	printk(KERN_INFO "utodr : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->utodr, in_be16(&uccf->uf_regs->utodr));
+		  &uccf->uf_regs->utodr, qe_ioread16be(&uccf->uf_regs->utodr));
 	printk(KERN_INFO "udsr  : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->udsr, in_be16(&uccf->uf_regs->udsr));
+		  &uccf->uf_regs->udsr, qe_ioread16be(&uccf->uf_regs->udsr));
 	printk(KERN_INFO "ucce  : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->ucce, in_be32(&uccf->uf_regs->ucce));
+		  &uccf->uf_regs->ucce, qe_ioread32be(&uccf->uf_regs->ucce));
 	printk(KERN_INFO "uccm  : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->uccm, in_be32(&uccf->uf_regs->uccm));
+		  &uccf->uf_regs->uccm, qe_ioread32be(&uccf->uf_regs->uccm));
 	printk(KERN_INFO "uccs  : addr=0x%p, val=0x%02x\n",
-		  &uccf->uf_regs->uccs, in_8(&uccf->uf_regs->uccs));
+		  &uccf->uf_regs->uccs, qe_ioread8(&uccf->uf_regs->uccs));
 	printk(KERN_INFO "urfb  : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->urfb, in_be32(&uccf->uf_regs->urfb));
+		  &uccf->uf_regs->urfb, qe_ioread32be(&uccf->uf_regs->urfb));
 	printk(KERN_INFO "urfs  : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->urfs, in_be16(&uccf->uf_regs->urfs));
+		  &uccf->uf_regs->urfs, qe_ioread16be(&uccf->uf_regs->urfs));
 	printk(KERN_INFO "urfet : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->urfet, in_be16(&uccf->uf_regs->urfet));
+		  &uccf->uf_regs->urfet, qe_ioread16be(&uccf->uf_regs->urfet));
 	printk(KERN_INFO "urfset: addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->urfset, in_be16(&uccf->uf_regs->urfset));
+		  &uccf->uf_regs->urfset,
+		  qe_ioread16be(&uccf->uf_regs->urfset));
 	printk(KERN_INFO "utfb  : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->utfb, in_be32(&uccf->uf_regs->utfb));
+		  &uccf->uf_regs->utfb, qe_ioread32be(&uccf->uf_regs->utfb));
 	printk(KERN_INFO "utfs  : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->utfs, in_be16(&uccf->uf_regs->utfs));
+		  &uccf->uf_regs->utfs, qe_ioread16be(&uccf->uf_regs->utfs));
 	printk(KERN_INFO "utfet : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->utfet, in_be16(&uccf->uf_regs->utfet));
+		  &uccf->uf_regs->utfet, qe_ioread16be(&uccf->uf_regs->utfet));
 	printk(KERN_INFO "utftt : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->utftt, in_be16(&uccf->uf_regs->utftt));
+		  &uccf->uf_regs->utftt, qe_ioread16be(&uccf->uf_regs->utftt));
 	printk(KERN_INFO "utpt  : addr=0x%p, val=0x%04x\n",
-		  &uccf->uf_regs->utpt, in_be16(&uccf->uf_regs->utpt));
+		  &uccf->uf_regs->utpt, qe_ioread16be(&uccf->uf_regs->utpt));
 	printk(KERN_INFO "urtry : addr=0x%p, val=0x%08x\n",
-		  &uccf->uf_regs->urtry, in_be32(&uccf->uf_regs->urtry));
+		  &uccf->uf_regs->urtry, qe_ioread32be(&uccf->uf_regs->urtry));
 	printk(KERN_INFO "guemr : addr=0x%p, val=0x%02x\n",
-		  &uccf->uf_regs->guemr, in_8(&uccf->uf_regs->guemr));
+		  &uccf->uf_regs->guemr, qe_ioread8(&uccf->uf_regs->guemr));
 }
 EXPORT_SYMBOL(ucc_fast_dump_regs);
 
@@ -85,7 +86,7 @@ EXPORT_SYMBOL(ucc_fast_get_qe_cr_subblock);
 
 void ucc_fast_transmit_on_demand(struct ucc_fast_private * uccf)
 {
-	out_be16(&uccf->uf_regs->utodr, UCC_FAST_TOD);
+	qe_iowrite16be(UCC_FAST_TOD, &uccf->uf_regs->utodr);
 }
 EXPORT_SYMBOL(ucc_fast_transmit_on_demand);
 
@@ -97,7 +98,7 @@ void ucc_fast_enable(struct ucc_fast_private * uccf, enum comm_dir mode)
 	uf_regs = uccf->uf_regs;
 
 	/* Enable reception and/or transmission on this UCC. */
-	gumr = in_be32(&uf_regs->gumr);
+	gumr = qe_ioread32be(&uf_regs->gumr);
 	if (mode & COMM_DIR_TX) {
 		gumr |= UCC_FAST_GUMR_ENT;
 		uccf->enabled_tx = 1;
@@ -106,7 +107,7 @@ void ucc_fast_enable(struct ucc_fast_private * uccf, enum comm_dir mode)
 		gumr |= UCC_FAST_GUMR_ENR;
 		uccf->enabled_rx = 1;
 	}
-	out_be32(&uf_regs->gumr, gumr);
+	qe_iowrite32be(gumr, &uf_regs->gumr);
 }
 EXPORT_SYMBOL(ucc_fast_enable);
 
@@ -118,7 +119,7 @@ void ucc_fast_disable(struct ucc_fast_private * uccf, enum comm_dir mode)
 	uf_regs = uccf->uf_regs;
 
 	/* Disable reception and/or transmission on this UCC. */
-	gumr = in_be32(&uf_regs->gumr);
+	gumr = qe_ioread32be(&uf_regs->gumr);
 	if (mode & COMM_DIR_TX) {
 		gumr &= ~UCC_FAST_GUMR_ENT;
 		uccf->enabled_tx = 0;
@@ -127,7 +128,7 @@ void ucc_fast_disable(struct ucc_fast_private * uccf, enum comm_dir mode)
 		gumr &= ~UCC_FAST_GUMR_ENR;
 		uccf->enabled_rx = 0;
 	}
-	out_be32(&uf_regs->gumr, gumr);
+	qe_iowrite32be(gumr, &uf_regs->gumr);
 }
 EXPORT_SYMBOL(ucc_fast_disable);
 
@@ -259,7 +260,7 @@ int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** ucc
 	gumr |= uf_info->tenc;
 	gumr |= uf_info->tcrc;
 	gumr |= uf_info->mode;
-	out_be32(&uf_regs->gumr, gumr);
+	qe_iowrite32be(gumr, &uf_regs->gumr);
 
 	/* Allocate memory for Tx Virtual Fifo */
 	uccf->ucc_fast_tx_virtual_fifo_base_offset =
@@ -286,15 +287,17 @@ int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** ucc
 	}
 
 	/* Set Virtual Fifo registers */
-	out_be16(&uf_regs->urfs, uf_info->urfs);
-	out_be16(&uf_regs->urfet, uf_info->urfet);
-	out_be16(&uf_regs->urfset, uf_info->urfset);
-	out_be16(&uf_regs->utfs, uf_info->utfs);
-	out_be16(&uf_regs->utfet, uf_info->utfet);
-	out_be16(&uf_regs->utftt, uf_info->utftt);
+	qe_iowrite16be(uf_info->urfs, &uf_regs->urfs);
+	qe_iowrite16be(uf_info->urfet, &uf_regs->urfet);
+	qe_iowrite16be(uf_info->urfset, &uf_regs->urfset);
+	qe_iowrite16be(uf_info->utfs, &uf_regs->utfs);
+	qe_iowrite16be(uf_info->utfet, &uf_regs->utfet);
+	qe_iowrite16be(uf_info->utftt, &uf_regs->utftt);
 	/* utfb, urfb are offsets from MURAM base */
-	out_be32(&uf_regs->utfb, uccf->ucc_fast_tx_virtual_fifo_base_offset);
-	out_be32(&uf_regs->urfb, uccf->ucc_fast_rx_virtual_fifo_base_offset);
+	qe_iowrite32be(uccf->ucc_fast_tx_virtual_fifo_base_offset,
+		       &uf_regs->utfb);
+	qe_iowrite32be(uccf->ucc_fast_rx_virtual_fifo_base_offset,
+		       &uf_regs->urfb);
 
 	/* Mux clocking */
 	/* Grant Support */
@@ -362,14 +365,14 @@ int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** ucc
 	}
 
 	/* Set interrupt mask register at UCC level. */
-	out_be32(&uf_regs->uccm, uf_info->uccm_mask);
+	qe_iowrite32be(uf_info->uccm_mask, &uf_regs->uccm);
 
 	/* First, clear anything pending at UCC level,
 	 * otherwise, old garbage may come through
 	 * as soon as the dam is opened. */
 
 	/* Writing '1' clears */
-	out_be32(&uf_regs->ucce, 0xffffffff);
+	qe_iowrite32be(0xffffffff, &uf_regs->ucce);
 
 	*uccf_ret = uccf;
 	return 0;
diff --git a/drivers/soc/fsl/qe/ucc_slow.c b/drivers/soc/fsl/qe/ucc_slow.c
index 34f0ec3a63b5..9b55fd0f50c6 100644
--- a/drivers/soc/fsl/qe/ucc_slow.c
+++ b/drivers/soc/fsl/qe/ucc_slow.c
@@ -78,7 +78,7 @@ void ucc_slow_enable(struct ucc_slow_private * uccs, enum comm_dir mode)
 	us_regs = uccs->us_regs;
 
 	/* Enable reception and/or transmission on this UCC. */
-	gumr_l = in_be32(&us_regs->gumr_l);
+	gumr_l = qe_ioread32be(&us_regs->gumr_l);
 	if (mode & COMM_DIR_TX) {
 		gumr_l |= UCC_SLOW_GUMR_L_ENT;
 		uccs->enabled_tx = 1;
@@ -87,7 +87,7 @@ void ucc_slow_enable(struct ucc_slow_private * uccs, enum comm_dir mode)
 		gumr_l |= UCC_SLOW_GUMR_L_ENR;
 		uccs->enabled_rx = 1;
 	}
-	out_be32(&us_regs->gumr_l, gumr_l);
+	qe_iowrite32be(gumr_l, &us_regs->gumr_l);
 }
 EXPORT_SYMBOL(ucc_slow_enable);
 
@@ -99,7 +99,7 @@ void ucc_slow_disable(struct ucc_slow_private * uccs, enum comm_dir mode)
 	us_regs = uccs->us_regs;
 
 	/* Disable reception and/or transmission on this UCC. */
-	gumr_l = in_be32(&us_regs->gumr_l);
+	gumr_l = qe_ioread32be(&us_regs->gumr_l);
 	if (mode & COMM_DIR_TX) {
 		gumr_l &= ~UCC_SLOW_GUMR_L_ENT;
 		uccs->enabled_tx = 0;
@@ -108,7 +108,7 @@ void ucc_slow_disable(struct ucc_slow_private * uccs, enum comm_dir mode)
 		gumr_l &= ~UCC_SLOW_GUMR_L_ENR;
 		uccs->enabled_rx = 0;
 	}
-	out_be32(&us_regs->gumr_l, gumr_l);
+	qe_iowrite32be(gumr_l, &us_regs->gumr_l);
 }
 EXPORT_SYMBOL(ucc_slow_disable);
 
@@ -198,7 +198,7 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 		return ret;
 	}
 
-	out_be16(&uccs->us_pram->mrblr, us_info->max_rx_buf_length);
+	qe_iowrite16be(us_info->max_rx_buf_length, &uccs->us_pram->mrblr);
 
 	INIT_LIST_HEAD(&uccs->confQ);
 
@@ -228,27 +228,27 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 	bd = uccs->confBd = uccs->tx_bd = qe_muram_addr(uccs->tx_base_offset);
 	for (i = 0; i < us_info->tx_bd_ring_len - 1; i++) {
 		/* clear bd buffer */
-		out_be32(&bd->buf, 0);
+		qe_iowrite32be(0, &bd->buf);
 		/* set bd status and length */
-		out_be32((u32 *) bd, 0);
+		qe_iowrite32be(0, (u32 *)bd);
 		bd++;
 	}
 	/* for last BD set Wrap bit */
-	out_be32(&bd->buf, 0);
-	out_be32((u32 *) bd, cpu_to_be32(T_W));
+	qe_iowrite32be(0, &bd->buf);
+	qe_iowrite32be(cpu_to_be32(T_W), (u32 *)bd);
 
 	/* Init Rx bds */
 	bd = uccs->rx_bd = qe_muram_addr(uccs->rx_base_offset);
 	for (i = 0; i < us_info->rx_bd_ring_len - 1; i++) {
 		/* set bd status and length */
-		out_be32((u32*)bd, 0);
+		qe_iowrite32be(0, (u32 *)bd);
 		/* clear bd buffer */
-		out_be32(&bd->buf, 0);
+		qe_iowrite32be(0, &bd->buf);
 		bd++;
 	}
 	/* for last BD set Wrap bit */
-	out_be32((u32*)bd, cpu_to_be32(R_W));
-	out_be32(&bd->buf, 0);
+	qe_iowrite32be(cpu_to_be32(R_W), (u32 *)bd);
+	qe_iowrite32be(0, &bd->buf);
 
 	/* Set GUMR (For more details see the hardware spec.). */
 	/* gumr_h */
@@ -269,7 +269,7 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 		gumr |= UCC_SLOW_GUMR_H_TXSY;
 	if (us_info->rtsm)
 		gumr |= UCC_SLOW_GUMR_H_RTSM;
-	out_be32(&us_regs->gumr_h, gumr);
+	qe_iowrite32be(gumr, &us_regs->gumr_h);
 
 	/* gumr_l */
 	gumr = us_info->tdcr | us_info->rdcr | us_info->tenc | us_info->renc |
@@ -282,7 +282,7 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 		gumr |= UCC_SLOW_GUMR_L_TINV;
 	if (us_info->tend)
 		gumr |= UCC_SLOW_GUMR_L_TEND;
-	out_be32(&us_regs->gumr_l, gumr);
+	qe_iowrite32be(gumr, &us_regs->gumr_l);
 
 	/* Function code registers */
 
@@ -292,8 +292,8 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 	uccs->us_pram->rbmr = UCC_BMR_BO_BE;
 
 	/* rbase, tbase are offsets from MURAM base */
-	out_be16(&uccs->us_pram->rbase, uccs->rx_base_offset);
-	out_be16(&uccs->us_pram->tbase, uccs->tx_base_offset);
+	qe_iowrite16be(uccs->rx_base_offset, &uccs->us_pram->rbase);
+	qe_iowrite16be(uccs->tx_base_offset, &uccs->us_pram->tbase);
 
 	/* Mux clocking */
 	/* Grant Support */
@@ -323,14 +323,14 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 	}
 
 	/* Set interrupt mask register at UCC level. */
-	out_be16(&us_regs->uccm, us_info->uccm_mask);
+	qe_iowrite16be(us_info->uccm_mask, &us_regs->uccm);
 
 	/* First, clear anything pending at UCC level,
 	 * otherwise, old garbage may come through
 	 * as soon as the dam is opened. */
 
 	/* Writing '1' clears */
-	out_be16(&us_regs->ucce, 0xffff);
+	qe_iowrite16be(0xffff, &us_regs->ucce);
 
 	/* Issue QE Init command */
 	if (us_info->init_tx && us_info->init_rx)
diff --git a/drivers/soc/fsl/qe/usb.c b/drivers/soc/fsl/qe/usb.c
index 32d8269fa692..890f236ea697 100644
--- a/drivers/soc/fsl/qe/usb.c
+++ b/drivers/soc/fsl/qe/usb.c
@@ -43,7 +43,7 @@ int qe_usb_clock_set(enum qe_clock clk, int rate)
 
 	spin_lock_irqsave(&cmxgcr_lock, flags);
 
-	clrsetbits_be32(&mux->cmxgcr, QE_CMXGCR_USBCS, val);
+	qe_clrsetbits_be32(&mux->cmxgcr, QE_CMXGCR_USBCS, val);
 
 	spin_unlock_irqrestore(&cmxgcr_lock, flags);
 
-- 
2.23.0

[PATCH v6 06/49] soc: fsl: qe: replace spin_event_timeout by readx_poll_timeout_atomic

[Rasmus Villemoes]

In preparation for allowing QE to be built for architectures other
than ppc, use the generic readx_poll_timeout_atomic() helper from
iopoll.h rather than the ppc-only spin_event_timeout().

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c | 13 +++++++------
 1 file changed, 7 insertions(+), 6 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index 456bd7416876..85737e6f5b62 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -22,6 +22,7 @@
 #include <linux/module.h>
 #include <linux/delay.h>
 #include <linux/ioport.h>
+#include <linux/iopoll.h>
 #include <linux/crc32.h>
 #include <linux/mod_devicetable.h>
 #include <linux/of_platform.h>
@@ -108,7 +109,8 @@ int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input)
 {
 	unsigned long flags;
 	u8 mcn_shift = 0, dev_shift = 0;
-	u32 ret;
+	u32 val;
+	int ret;
 
 	spin_lock_irqsave(&qe_lock, flags);
 	if (cmd == QE_RESET) {
@@ -135,13 +137,12 @@ int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input)
 	}
 
 	/* wait for the QE_CR_FLG to clear */
-	ret = spin_event_timeout((qe_ioread32be(&qe_immr->cp.cecr) & QE_CR_FLG) == 0,
-				 100, 0);
-	/* On timeout (e.g. failure), the expression will be false (ret == 0),
-	   otherwise it will be true (ret == 1). */
+	ret = readx_poll_timeout_atomic(qe_ioread32be, &qe_immr->cp.cecr, val,
+					(val & QE_CR_FLG) == 0, 0, 100);
+	/* On timeout, ret is -ETIMEDOUT, otherwise it will be 0. */
 	spin_unlock_irqrestore(&qe_lock, flags);
 
-	return ret == 1;
+	return ret == 0;
 }
 EXPORT_SYMBOL(qe_issue_cmd);
 
-- 
2.23.0

[PATCH v6 07/49] soc: fsl: qe: qe.c: guard use of pvr_version_is() with CONFIG_PPC32

[Rasmus Villemoes]

Commit e5c5c8d23fef (soc/fsl/qe: only apply QE_General4 workaround on
affected SoCs) introduced use of pvr_version_is(), saying

    The QE_General4 workaround is only valid for the MPC832x and MPC836x
    SoCs. The other SoCs that embed a QUICC engine are not affected by this
    hardware bug and thus can use the computed divisors (this was
    successfully tested on the T1040).

I'm reading the above as saying that the errata does not apply to the
ARM-based SOCs with QUICC engine. In any case, use of pvr_version_is()
must be guarded by CONFIG_PPC32 before we can remove the PPC32
dependency from CONFIG_QUICC_ENGINE, so introduce qe_general4_errata()
to keep the necessary #ifdeffery localized to a trivial helper.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index 85737e6f5b62..1d8aa62c7ddf 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -197,6 +197,14 @@ EXPORT_SYMBOL(qe_get_brg_clk);
 #define PVR_VER_836x	0x8083
 #define PVR_VER_832x	0x8084
 
+static bool qe_general4_errata(void)
+{
+#ifdef CONFIG_PPC32
+	return pvr_version_is(PVR_VER_836x) || pvr_version_is(PVR_VER_832x);
+#endif
+	return false;
+}
+
 /* Program the BRG to the given sampling rate and multiplier
  *
  * @brg: the BRG, QE_BRG1 - QE_BRG16
@@ -223,7 +231,7 @@ int qe_setbrg(enum qe_clock brg, unsigned int rate, unsigned int multiplier)
 	/* Errata QE_General4, which affects some MPC832x and MPC836x SOCs, says
 	   that the BRG divisor must be even if you're not using divide-by-16
 	   mode. */
-	if (pvr_version_is(PVR_VER_836x) || pvr_version_is(PVR_VER_832x))
+	if (qe_general4_errata())
 		if (!div16 && (divisor & 1) && (divisor > 3))
 			divisor++;
 
-- 
2.23.0

[PATCH v6 08/49] soc: fsl: qe: drop unneeded #includes

[Rasmus Villemoes]

These includes are not actually needed, and asm/rheap.h and
sysdev/fsl_soc.h are PPC-specific, hence prevent compiling QE for
other architectures.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c    | 5 -----
 drivers/soc/fsl/qe/qe_io.c | 2 --
 2 files changed, 7 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index 1d8aa62c7ddf..a4763282ea68 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -26,13 +26,8 @@
 #include <linux/crc32.h>
 #include <linux/mod_devicetable.h>
 #include <linux/of_platform.h>
-#include <asm/irq.h>
-#include <asm/page.h>
-#include <asm/pgtable.h>
 #include <soc/fsl/qe/immap_qe.h>
 #include <soc/fsl/qe/qe.h>
-#include <asm/prom.h>
-#include <asm/rheap.h>
 
 static void qe_snums_init(void);
 static int qe_sdma_init(void);
diff --git a/drivers/soc/fsl/qe/qe_io.c b/drivers/soc/fsl/qe/qe_io.c
index 5e3471ac09dd..f6b10f38b2f4 100644
--- a/drivers/soc/fsl/qe/qe_io.c
+++ b/drivers/soc/fsl/qe/qe_io.c
@@ -18,8 +18,6 @@
 
 #include <asm/io.h>
 #include <soc/fsl/qe/qe.h>
-#include <asm/prom.h>
-#include <sysdev/fsl_soc.h>
 
 #undef DEBUG
 
-- 
2.23.0

[PATCH v6 09/49] soc: fsl: qe: drop assign-only high_active in qe_ic_init

[Rasmus Villemoes]

high_active is only assigned to but never used. Remove it.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 8c874372416b..4b03060d8079 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -320,7 +320,7 @@ void __init qe_ic_init(struct device_node *node, unsigned int flags,
 {
 	struct qe_ic *qe_ic;
 	struct resource res;
-	u32 temp = 0, ret, high_active = 0;
+	u32 temp = 0, ret;
 
 	ret = of_address_to_resource(node, 0, &res);
 	if (ret)
@@ -366,10 +366,8 @@ void __init qe_ic_init(struct device_node *node, unsigned int flags,
 		temp |= CICR_GRTB;
 
 	/* choose destination signal for highest priority interrupt */
-	if (flags & QE_IC_HIGH_SIGNAL) {
+	if (flags & QE_IC_HIGH_SIGNAL)
 		temp |= (SIGNAL_HIGH << CICR_HPIT_SHIFT);
-		high_active = 1;
-	}
 
 	qe_ic_write(qe_ic->regs, QEIC_CICR, temp);
 
-- 
2.23.0

[PATCH v6 10/49] soc: fsl: qe: remove pointless sysfs registration in qe_ic.c

[Rasmus Villemoes]

There's no point in registering with sysfs when that doesn't actually
allow any interaction with the device or driver (no uevents, no sysfs
files that provide information or allow configuration, no nothing).

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 31 -------------------------------
 1 file changed, 31 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 4b03060d8079..f170926ce4d1 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -474,34 +474,3 @@ int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high)
 
 	return 0;
 }
-
-static struct bus_type qe_ic_subsys = {
-	.name = "qe_ic",
-	.dev_name = "qe_ic",
-};
-
-static struct device device_qe_ic = {
-	.id = 0,
-	.bus = &qe_ic_subsys,
-};
-
-static int __init init_qe_ic_sysfs(void)
-{
-	int rc;
-
-	printk(KERN_DEBUG "Registering qe_ic with sysfs...\n");
-
-	rc = subsys_system_register(&qe_ic_subsys, NULL);
-	if (rc) {
-		printk(KERN_ERR "Failed registering qe_ic sys class\n");
-		return -ENODEV;
-	}
-	rc = device_register(&device_qe_ic);
-	if (rc) {
-		printk(KERN_ERR "Failed registering qe_ic sys device\n");
-		return -ENODEV;
-	}
-	return 0;
-}
-
-subsys_initcall(init_qe_ic_sysfs);
-- 
2.23.0

[PATCH v6 11/49] soc: fsl: qe: use qe_ic_cascade_{low,high}_mpic also on 83xx

[Rasmus Villemoes]

The *_ipic and *_mpic handlers are almost identical - the only
difference is that the latter end with an unconditional
chip->irq_eoi() call. Since IPIC does not have ->irq_eoi, we can
reduce some code duplication by calling irq_eoi conditionally.

This is similar to what is already done in mpc8xxx_gpio_irq_cascade().

This leaves the functions slightly misnamed, but that will be fixed in
a subsequent patch.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 arch/powerpc/platforms/83xx/misc.c |  2 +-
 include/soc/fsl/qe/qe_ic.h         | 24 ++++--------------------
 2 files changed, 5 insertions(+), 21 deletions(-)

diff --git a/arch/powerpc/platforms/83xx/misc.c b/arch/powerpc/platforms/83xx/misc.c
index f46d7bf3b140..779791c0570f 100644
--- a/arch/powerpc/platforms/83xx/misc.c
+++ b/arch/powerpc/platforms/83xx/misc.c
@@ -100,7 +100,7 @@ void __init mpc83xx_qe_init_IRQ(void)
 		if (!np)
 			return;
 	}
-	qe_ic_init(np, 0, qe_ic_cascade_low_ipic, qe_ic_cascade_high_ipic);
+	qe_ic_init(np, 0, qe_ic_cascade_low_mpic, qe_ic_cascade_high_mpic);
 	of_node_put(np);
 }
 
diff --git a/include/soc/fsl/qe/qe_ic.h b/include/soc/fsl/qe/qe_ic.h
index 714a9b890d8d..bfaa233d8328 100644
--- a/include/soc/fsl/qe/qe_ic.h
+++ b/include/soc/fsl/qe/qe_ic.h
@@ -74,24 +74,6 @@ void qe_ic_set_highest_priority(unsigned int virq, int high);
 int qe_ic_set_priority(unsigned int virq, unsigned int priority);
 int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high);
 
-static inline void qe_ic_cascade_low_ipic(struct irq_desc *desc)
-{
-	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
-	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
-
-	if (cascade_irq != NO_IRQ)
-		generic_handle_irq(cascade_irq);
-}
-
-static inline void qe_ic_cascade_high_ipic(struct irq_desc *desc)
-{
-	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
-	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
-
-	if (cascade_irq != NO_IRQ)
-		generic_handle_irq(cascade_irq);
-}
-
 static inline void qe_ic_cascade_low_mpic(struct irq_desc *desc)
 {
 	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
@@ -101,7 +83,8 @@ static inline void qe_ic_cascade_low_mpic(struct irq_desc *desc)
 	if (cascade_irq != NO_IRQ)
 		generic_handle_irq(cascade_irq);
 
-	chip->irq_eoi(&desc->irq_data);
+	if (chip->irq_eoi)
+		chip->irq_eoi(&desc->irq_data);
 }
 
 static inline void qe_ic_cascade_high_mpic(struct irq_desc *desc)
@@ -113,7 +96,8 @@ static inline void qe_ic_cascade_high_mpic(struct irq_desc *desc)
 	if (cascade_irq != NO_IRQ)
 		generic_handle_irq(cascade_irq);
 
-	chip->irq_eoi(&desc->irq_data);
+	if (chip->irq_eoi)
+		chip->irq_eoi(&desc->irq_data);
 }
 
 static inline void qe_ic_cascade_muxed_mpic(struct irq_desc *desc)
-- 
2.23.0

[PATCH v6 12/49] soc: fsl: qe: move calls of qe_ic_init out of arch/powerpc/

[Rasmus Villemoes]

Having to call qe_ic_init() from platform-specific code makes it
awkward to allow building the QE drivers for ARM. It's also a needless
duplication of code, and slightly error-prone: Instead of the caller
needing to know the details of whether the QUICC Engine High and QUICC
Engine Low are actually the same interrupt (see e.g. the machine_is()
in mpc85xx_mds_qeic_init), just let the init function choose the
appropriate handlers after it has parsed the DT and figured it out. If
the two interrupts are distinct, use separate handlers, otherwise use
the handler which first checks the CHIVEC register (for the high
priority interrupts), then the CIVEC.

All existing callers pass 0 for flags, so continue to do that from the
new single caller. Later cleanups will remove that argument
from qe_ic_init and simplify the body, as well as make qe_ic_init into
a proper init function for an IRQCHIP_DECLARE, eliminating the need to
manually look up the fsl,qe-ic node.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 arch/powerpc/platforms/83xx/km83xx.c          |  1 -
 arch/powerpc/platforms/83xx/misc.c            | 16 ----------
 arch/powerpc/platforms/83xx/mpc832x_mds.c     |  1 -
 arch/powerpc/platforms/83xx/mpc832x_rdb.c     |  1 -
 arch/powerpc/platforms/83xx/mpc836x_mds.c     |  1 -
 arch/powerpc/platforms/83xx/mpc836x_rdk.c     |  1 -
 arch/powerpc/platforms/83xx/mpc83xx.h         |  2 --
 arch/powerpc/platforms/85xx/corenet_generic.c | 10 -------
 arch/powerpc/platforms/85xx/mpc85xx_mds.c     | 27 -----------------
 arch/powerpc/platforms/85xx/mpc85xx_rdb.c     | 17 -----------
 arch/powerpc/platforms/85xx/twr_p102x.c       | 15 ----------
 drivers/soc/fsl/qe/qe_ic.c                    | 29 +++++++++++++++++--
 include/soc/fsl/qe/qe_ic.h                    |  7 -----
 13 files changed, 26 insertions(+), 102 deletions(-)

diff --git a/arch/powerpc/platforms/83xx/km83xx.c b/arch/powerpc/platforms/83xx/km83xx.c
index 273145aed90a..5c6227f7bc37 100644
--- a/arch/powerpc/platforms/83xx/km83xx.c
+++ b/arch/powerpc/platforms/83xx/km83xx.c
@@ -34,7 +34,6 @@
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 
 #include "mpc83xx.h"
 
diff --git a/arch/powerpc/platforms/83xx/misc.c b/arch/powerpc/platforms/83xx/misc.c
index 779791c0570f..6935a5b9fbd1 100644
--- a/arch/powerpc/platforms/83xx/misc.c
+++ b/arch/powerpc/platforms/83xx/misc.c
@@ -14,7 +14,6 @@
 #include <asm/io.h>
 #include <asm/hw_irq.h>
 #include <asm/ipic.h>
-#include <soc/fsl/qe/qe_ic.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
 
@@ -90,24 +89,9 @@ void __init mpc83xx_ipic_init_IRQ(void)
 }
 
 #ifdef CONFIG_QUICC_ENGINE
-void __init mpc83xx_qe_init_IRQ(void)
-{
-	struct device_node *np;
-
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
-	if (!np) {
-		np = of_find_node_by_type(NULL, "qeic");
-		if (!np)
-			return;
-	}
-	qe_ic_init(np, 0, qe_ic_cascade_low_mpic, qe_ic_cascade_high_mpic);
-	of_node_put(np);
-}
-
 void __init mpc83xx_ipic_and_qe_init_IRQ(void)
 {
 	mpc83xx_ipic_init_IRQ();
-	mpc83xx_qe_init_IRQ();
 }
 #endif /* CONFIG_QUICC_ENGINE */
 
diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.c b/arch/powerpc/platforms/83xx/mpc832x_mds.c
index b428835e5919..1c73af104d19 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
@@ -33,7 +33,6 @@
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 
 #include "mpc83xx.h"
 
diff --git a/arch/powerpc/platforms/83xx/mpc832x_rdb.c b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
index 4588ce632484..87f68ca06255 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
@@ -22,7 +22,6 @@
 #include <asm/ipic.h>
 #include <asm/udbg.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
 
diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c
index 4a4efa906d35..5b484da9533e 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c
@@ -41,7 +41,6 @@
 #include <sysdev/fsl_pci.h>
 #include <sysdev/simple_gpio.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 
 #include "mpc83xx.h"
 
diff --git a/arch/powerpc/platforms/83xx/mpc836x_rdk.c b/arch/powerpc/platforms/83xx/mpc836x_rdk.c
index 9923059cb111..b7119e443920 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_rdk.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_rdk.c
@@ -17,7 +17,6 @@
 #include <asm/ipic.h>
 #include <asm/udbg.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
 
diff --git a/arch/powerpc/platforms/83xx/mpc83xx.h b/arch/powerpc/platforms/83xx/mpc83xx.h
index 459145623334..d343f6ce2599 100644
--- a/arch/powerpc/platforms/83xx/mpc83xx.h
+++ b/arch/powerpc/platforms/83xx/mpc83xx.h
@@ -73,10 +73,8 @@ extern int mpc834x_usb_cfg(void);
 extern int mpc831x_usb_cfg(void);
 extern void mpc83xx_ipic_init_IRQ(void);
 #ifdef CONFIG_QUICC_ENGINE
-extern void mpc83xx_qe_init_IRQ(void);
 extern void mpc83xx_ipic_and_qe_init_IRQ(void);
 #else
-static inline void __init mpc83xx_qe_init_IRQ(void) {}
 #define mpc83xx_ipic_and_qe_init_IRQ mpc83xx_ipic_init_IRQ
 #endif /* CONFIG_QUICC_ENGINE */
 
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 7ee2c6628f64..8c1bb3941642 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -24,7 +24,6 @@
 #include <asm/mpic.h>
 #include <asm/ehv_pic.h>
 #include <asm/swiotlb.h>
-#include <soc/fsl/qe/qe_ic.h>
 
 #include <linux/of_platform.h>
 #include <sysdev/fsl_soc.h>
@@ -38,8 +37,6 @@ void __init corenet_gen_pic_init(void)
 	unsigned int flags = MPIC_BIG_ENDIAN | MPIC_SINGLE_DEST_CPU |
 		MPIC_NO_RESET;
 
-	struct device_node *np;
-
 	if (ppc_md.get_irq == mpic_get_coreint_irq)
 		flags |= MPIC_ENABLE_COREINT;
 
@@ -47,13 +44,6 @@ void __init corenet_gen_pic_init(void)
 	BUG_ON(mpic == NULL);
 
 	mpic_init(mpic);
-
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
-	if (np) {
-		qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
-				qe_ic_cascade_high_mpic);
-		of_node_put(np);
-	}
 }
 
 /*
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 5ca254256c47..4bc49e5ec0b6 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -45,7 +45,6 @@
 #include <sysdev/fsl_pci.h>
 #include <sysdev/simple_gpio.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 #include <asm/mpic.h>
 #include <asm/swiotlb.h>
 #include "smp.h"
@@ -270,33 +269,8 @@ static void __init mpc85xx_mds_qe_init(void)
 	}
 }
 
-static void __init mpc85xx_mds_qeic_init(void)
-{
-	struct device_node *np;
-
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!of_device_is_available(np)) {
-		of_node_put(np);
-		return;
-	}
-
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
-	if (!np) {
-		np = of_find_node_by_type(NULL, "qeic");
-		if (!np)
-			return;
-	}
-
-	if (machine_is(p1021_mds))
-		qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
-				qe_ic_cascade_high_mpic);
-	else
-		qe_ic_init(np, 0, qe_ic_cascade_muxed_mpic, NULL);
-	of_node_put(np);
-}
 #else
 static void __init mpc85xx_mds_qe_init(void) { }
-static void __init mpc85xx_mds_qeic_init(void) { }
 #endif	/* CONFIG_QUICC_ENGINE */
 
 static void __init mpc85xx_mds_setup_arch(void)
@@ -371,7 +345,6 @@ static void __init mpc85xx_mds_pic_init(void)
 	BUG_ON(mpic == NULL);
 
 	mpic_init(mpic);
-	mpc85xx_mds_qeic_init();
 }
 
 static int __init mpc85xx_mds_probe(void)
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
index d3c540ee558f..14b5a61d49c1 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
@@ -23,7 +23,6 @@
 #include <asm/udbg.h>
 #include <asm/mpic.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
@@ -44,10 +43,6 @@ void __init mpc85xx_rdb_pic_init(void)
 {
 	struct mpic *mpic;
 
-#ifdef CONFIG_QUICC_ENGINE
-	struct device_node *np;
-#endif
-
 	if (of_machine_is_compatible("fsl,MPC85XXRDB-CAMP")) {
 		mpic = mpic_alloc(NULL, 0, MPIC_NO_RESET |
 			MPIC_BIG_ENDIAN |
@@ -62,18 +57,6 @@ void __init mpc85xx_rdb_pic_init(void)
 
 	BUG_ON(mpic == NULL);
 	mpic_init(mpic);
-
-#ifdef CONFIG_QUICC_ENGINE
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
-	if (np) {
-		qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
-				qe_ic_cascade_high_mpic);
-		of_node_put(np);
-
-	} else
-		pr_err("%s: Could not find qe-ic node\n", __func__);
-#endif
-
 }
 
 /*
diff --git a/arch/powerpc/platforms/85xx/twr_p102x.c b/arch/powerpc/platforms/85xx/twr_p102x.c
index 720b0c0f03ba..b099f5607120 100644
--- a/arch/powerpc/platforms/85xx/twr_p102x.c
+++ b/arch/powerpc/platforms/85xx/twr_p102x.c
@@ -19,7 +19,6 @@
 #include <asm/udbg.h>
 #include <asm/mpic.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
@@ -31,26 +30,12 @@ static void __init twr_p1025_pic_init(void)
 {
 	struct mpic *mpic;
 
-#ifdef CONFIG_QUICC_ENGINE
-	struct device_node *np;
-#endif
-
 	mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
 			MPIC_SINGLE_DEST_CPU,
 			0, 256, " OpenPIC  ");
 
 	BUG_ON(mpic == NULL);
 	mpic_init(mpic);
-
-#ifdef CONFIG_QUICC_ENGINE
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
-	if (np) {
-		qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
-				qe_ic_cascade_high_mpic);
-		of_node_put(np);
-	} else
-		pr_err("Could not find qe-ic node\n");
-#endif
 }
 
 /* ************************************************************************
diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index f170926ce4d1..a062efac398b 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -314,10 +314,10 @@ unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 	return irq_linear_revmap(qe_ic->irqhost, irq);
 }
 
-void __init qe_ic_init(struct device_node *node, unsigned int flags,
-		       void (*low_handler)(struct irq_desc *desc),
-		       void (*high_handler)(struct irq_desc *desc))
+static void __init qe_ic_init(struct device_node *node, unsigned int flags)
 {
+	void (*low_handler)(struct irq_desc *desc);
+	void (*high_handler)(struct irq_desc *desc);
 	struct qe_ic *qe_ic;
 	struct resource res;
 	u32 temp = 0, ret;
@@ -349,6 +349,13 @@ void __init qe_ic_init(struct device_node *node, unsigned int flags,
 		kfree(qe_ic);
 		return;
 	}
+	if (qe_ic->virq_high != qe_ic->virq_low) {
+		low_handler = qe_ic_cascade_low_mpic;
+		high_handler = qe_ic_cascade_high_mpic;
+	} else {
+		low_handler = qe_ic_cascade_muxed_mpic;
+		high_handler = NULL;
+	}
 
 	/* default priority scheme is grouped. If spread mode is    */
 	/* required, configure cicr accordingly.                    */
@@ -381,6 +388,22 @@ void __init qe_ic_init(struct device_node *node, unsigned int flags,
 	}
 }
 
+static int __init qe_ic_of_init(void)
+{
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
+	if (!np) {
+		np = of_find_node_by_type(NULL, "qeic");
+		if (!np)
+			return -ENODEV;
+	}
+	qe_ic_init(np, 0);
+	of_node_put(np);
+	return 0;
+}
+subsys_initcall(qe_ic_of_init);
+
 void qe_ic_set_highest_priority(unsigned int virq, int high)
 {
 	struct qe_ic *qe_ic = qe_ic_from_irq(virq);
diff --git a/include/soc/fsl/qe/qe_ic.h b/include/soc/fsl/qe/qe_ic.h
index bfaa233d8328..a47a0d26acbd 100644
--- a/include/soc/fsl/qe/qe_ic.h
+++ b/include/soc/fsl/qe/qe_ic.h
@@ -54,16 +54,9 @@ enum qe_ic_grp_id {
 };
 
 #ifdef CONFIG_QUICC_ENGINE
-void qe_ic_init(struct device_node *node, unsigned int flags,
-		void (*low_handler)(struct irq_desc *desc),
-		void (*high_handler)(struct irq_desc *desc));
 unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
 unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
 #else
-static inline void qe_ic_init(struct device_node *node, unsigned int flags,
-		void (*low_handler)(struct irq_desc *desc),
-		void (*high_handler)(struct irq_desc *desc))
-{}
 static inline unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
 { return 0; }
 static inline unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
-- 
2.23.0

[PATCH v6 13/49] powerpc/83xx: remove mpc83xx_ipic_and_qe_init_IRQ

[Rasmus Villemoes]

This is now exactly the same as mpc83xx_ipic_init_IRQ, so just use
that directly.

Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 arch/powerpc/platforms/83xx/km83xx.c      | 2 +-
 arch/powerpc/platforms/83xx/misc.c        | 7 -------
 arch/powerpc/platforms/83xx/mpc832x_mds.c | 2 +-
 arch/powerpc/platforms/83xx/mpc832x_rdb.c | 2 +-
 arch/powerpc/platforms/83xx/mpc836x_mds.c | 2 +-
 arch/powerpc/platforms/83xx/mpc836x_rdk.c | 2 +-
 arch/powerpc/platforms/83xx/mpc83xx.h     | 5 -----
 7 files changed, 5 insertions(+), 17 deletions(-)

diff --git a/arch/powerpc/platforms/83xx/km83xx.c b/arch/powerpc/platforms/83xx/km83xx.c
index 5c6227f7bc37..3d89569e9e71 100644
--- a/arch/powerpc/platforms/83xx/km83xx.c
+++ b/arch/powerpc/platforms/83xx/km83xx.c
@@ -177,7 +177,7 @@ define_machine(mpc83xx_km) {
 	.name		= "mpc83xx-km-platform",
 	.probe		= mpc83xx_km_probe,
 	.setup_arch	= mpc83xx_km_setup_arch,
-	.init_IRQ	= mpc83xx_ipic_and_qe_init_IRQ,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
 	.get_irq	= ipic_get_irq,
 	.restart	= mpc83xx_restart,
 	.time_init	= mpc83xx_time_init,
diff --git a/arch/powerpc/platforms/83xx/misc.c b/arch/powerpc/platforms/83xx/misc.c
index 6935a5b9fbd1..1d8306eb2958 100644
--- a/arch/powerpc/platforms/83xx/misc.c
+++ b/arch/powerpc/platforms/83xx/misc.c
@@ -88,13 +88,6 @@ void __init mpc83xx_ipic_init_IRQ(void)
 	ipic_set_default_priority();
 }
 
-#ifdef CONFIG_QUICC_ENGINE
-void __init mpc83xx_ipic_and_qe_init_IRQ(void)
-{
-	mpc83xx_ipic_init_IRQ();
-}
-#endif /* CONFIG_QUICC_ENGINE */
-
 static const struct of_device_id of_bus_ids[] __initconst = {
 	{ .type = "soc", },
 	{ .compatible = "soc", },
diff --git a/arch/powerpc/platforms/83xx/mpc832x_mds.c b/arch/powerpc/platforms/83xx/mpc832x_mds.c
index 1c73af104d19..6fa5402ebf20 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_mds.c
@@ -101,7 +101,7 @@ define_machine(mpc832x_mds) {
 	.name 		= "MPC832x MDS",
 	.probe 		= mpc832x_sys_probe,
 	.setup_arch 	= mpc832x_sys_setup_arch,
-	.init_IRQ	= mpc83xx_ipic_and_qe_init_IRQ,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
 	.get_irq 	= ipic_get_irq,
 	.restart 	= mpc83xx_restart,
 	.time_init 	= mpc83xx_time_init,
diff --git a/arch/powerpc/platforms/83xx/mpc832x_rdb.c b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
index 87f68ca06255..622c625d5ce4 100644
--- a/arch/powerpc/platforms/83xx/mpc832x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc832x_rdb.c
@@ -219,7 +219,7 @@ define_machine(mpc832x_rdb) {
 	.name		= "MPC832x RDB",
 	.probe		= mpc832x_rdb_probe,
 	.setup_arch	= mpc832x_rdb_setup_arch,
-	.init_IRQ	= mpc83xx_ipic_and_qe_init_IRQ,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
 	.get_irq	= ipic_get_irq,
 	.restart	= mpc83xx_restart,
 	.time_init	= mpc83xx_time_init,
diff --git a/arch/powerpc/platforms/83xx/mpc836x_mds.c b/arch/powerpc/platforms/83xx/mpc836x_mds.c
index 5b484da9533e..219a83ab6c00 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_mds.c
@@ -208,7 +208,7 @@ define_machine(mpc836x_mds) {
 	.name		= "MPC836x MDS",
 	.probe		= mpc836x_mds_probe,
 	.setup_arch	= mpc836x_mds_setup_arch,
-	.init_IRQ	= mpc83xx_ipic_and_qe_init_IRQ,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
 	.get_irq	= ipic_get_irq,
 	.restart	= mpc83xx_restart,
 	.time_init	= mpc83xx_time_init,
diff --git a/arch/powerpc/platforms/83xx/mpc836x_rdk.c b/arch/powerpc/platforms/83xx/mpc836x_rdk.c
index b7119e443920..b4aac2cde849 100644
--- a/arch/powerpc/platforms/83xx/mpc836x_rdk.c
+++ b/arch/powerpc/platforms/83xx/mpc836x_rdk.c
@@ -41,7 +41,7 @@ define_machine(mpc836x_rdk) {
 	.name		= "MPC836x RDK",
 	.probe		= mpc836x_rdk_probe,
 	.setup_arch	= mpc836x_rdk_setup_arch,
-	.init_IRQ	= mpc83xx_ipic_and_qe_init_IRQ,
+	.init_IRQ	= mpc83xx_ipic_init_IRQ,
 	.get_irq	= ipic_get_irq,
 	.restart	= mpc83xx_restart,
 	.time_init	= mpc83xx_time_init,
diff --git a/arch/powerpc/platforms/83xx/mpc83xx.h b/arch/powerpc/platforms/83xx/mpc83xx.h
index d343f6ce2599..f37d04332fc7 100644
--- a/arch/powerpc/platforms/83xx/mpc83xx.h
+++ b/arch/powerpc/platforms/83xx/mpc83xx.h
@@ -72,11 +72,6 @@ extern int mpc837x_usb_cfg(void);
 extern int mpc834x_usb_cfg(void);
 extern int mpc831x_usb_cfg(void);
 extern void mpc83xx_ipic_init_IRQ(void);
-#ifdef CONFIG_QUICC_ENGINE
-extern void mpc83xx_ipic_and_qe_init_IRQ(void);
-#else
-#define mpc83xx_ipic_and_qe_init_IRQ mpc83xx_ipic_init_IRQ
-#endif /* CONFIG_QUICC_ENGINE */
 
 #ifdef CONFIG_PCI
 extern void mpc83xx_setup_pci(void);
-- 
2.23.0

[PATCH v6 14/49] powerpc/85xx: remove mostly pointless mpc85xx_qe_init()

[Rasmus Villemoes]

Since commit 302c059f2e7b (QE: use subsys_initcall to init qe),
mpc85xx_qe_init() has done nothing apart from possibly emitting a
pr_err(). As part of reducing the amount of QE-related code in
arch/powerpc/ (and eventually support QE on other architectures),
remove this low-hanging fruit.

Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 arch/powerpc/platforms/85xx/common.c          | 23 -------------------
 arch/powerpc/platforms/85xx/corenet_generic.c |  2 --
 arch/powerpc/platforms/85xx/mpc85xx.h         |  2 --
 arch/powerpc/platforms/85xx/mpc85xx_mds.c     |  1 -
 arch/powerpc/platforms/85xx/mpc85xx_rdb.c     |  1 -
 arch/powerpc/platforms/85xx/twr_p102x.c       |  1 -
 6 files changed, 30 deletions(-)

diff --git a/arch/powerpc/platforms/85xx/common.c b/arch/powerpc/platforms/85xx/common.c
index fe0606439b5a..a554b6d87cf7 100644
--- a/arch/powerpc/platforms/85xx/common.c
+++ b/arch/powerpc/platforms/85xx/common.c
@@ -86,29 +86,6 @@ void __init mpc85xx_cpm2_pic_init(void)
 #endif
 
 #ifdef CONFIG_QUICC_ENGINE
-void __init mpc85xx_qe_init(void)
-{
-	struct device_node *np;
-
-	np = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!np) {
-		np = of_find_node_by_name(NULL, "qe");
-		if (!np) {
-			pr_err("%s: Could not find Quicc Engine node\n",
-					__func__);
-			return;
-		}
-	}
-
-	if (!of_device_is_available(np)) {
-		of_node_put(np);
-		return;
-	}
-
-	of_node_put(np);
-
-}
-
 void __init mpc85xx_qe_par_io_init(void)
 {
 	struct device_node *np;
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 8c1bb3941642..27ac38f7e1a9 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -56,8 +56,6 @@ void __init corenet_gen_setup_arch(void)
 	swiotlb_detect_4g();
 
 	pr_info("%s board\n", ppc_md.name);
-
-	mpc85xx_qe_init();
 }
 
 static const struct of_device_id of_device_ids[] = {
diff --git a/arch/powerpc/platforms/85xx/mpc85xx.h b/arch/powerpc/platforms/85xx/mpc85xx.h
index fa23f9b0592c..cb84c5c56c36 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx.h
+++ b/arch/powerpc/platforms/85xx/mpc85xx.h
@@ -10,10 +10,8 @@ static inline void __init mpc85xx_cpm2_pic_init(void) {}
 #endif /* CONFIG_CPM2 */
 
 #ifdef CONFIG_QUICC_ENGINE
-extern void mpc85xx_qe_init(void);
 extern void mpc85xx_qe_par_io_init(void);
 #else
-static inline void __init mpc85xx_qe_init(void) {}
 static inline void __init mpc85xx_qe_par_io_init(void) {}
 #endif
 
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 4bc49e5ec0b6..fb05b4d5bf1e 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -237,7 +237,6 @@ static void __init mpc85xx_mds_qe_init(void)
 {
 	struct device_node *np;
 
-	mpc85xx_qe_init();
 	mpc85xx_qe_par_io_init();
 	mpc85xx_mds_reset_ucc_phys();
 
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
index 14b5a61d49c1..80a80174768c 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_rdb.c
@@ -72,7 +72,6 @@ static void __init mpc85xx_rdb_setup_arch(void)
 	fsl_pci_assign_primary();
 
 #ifdef CONFIG_QUICC_ENGINE
-	mpc85xx_qe_init();
 	mpc85xx_qe_par_io_init();
 #if defined(CONFIG_UCC_GETH) || defined(CONFIG_SERIAL_QE)
 	if (machine_is(p1025_rdb)) {
diff --git a/arch/powerpc/platforms/85xx/twr_p102x.c b/arch/powerpc/platforms/85xx/twr_p102x.c
index b099f5607120..9abb1e9f73c4 100644
--- a/arch/powerpc/platforms/85xx/twr_p102x.c
+++ b/arch/powerpc/platforms/85xx/twr_p102x.c
@@ -57,7 +57,6 @@ static void __init twr_p1025_setup_arch(void)
 	fsl_pci_assign_primary();
 
 #ifdef CONFIG_QUICC_ENGINE
-	mpc85xx_qe_init();
 	mpc85xx_qe_par_io_init();
 
 #if IS_ENABLED(CONFIG_UCC_GETH) || IS_ENABLED(CONFIG_SERIAL_QE)
-- 
2.23.0

[PATCH v6 15/49] soc: fsl: qe: move qe_ic_cascade_* functions to qe_ic.c

[Rasmus Villemoes]

These functions are only ever called through a function pointer, and
therefore it makes no sense for them to be "static inline" - gcc has
no choice but to emit a copy in each translation unit that takes the
address of one of these. Since they are now only referenced from
qe_ic.c, just make them local to that file.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 42 ++++++++++++++++++++++++++++++++++++++
 include/soc/fsl/qe/qe_ic.h | 42 --------------------------------------
 2 files changed, 42 insertions(+), 42 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index a062efac398b..94ccbeeb1ad1 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -314,6 +314,48 @@ unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 	return irq_linear_revmap(qe_ic->irqhost, irq);
 }
 
+static void qe_ic_cascade_low_mpic(struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
+	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+
+	if (chip->irq_eoi)
+		chip->irq_eoi(&desc->irq_data);
+}
+
+static void qe_ic_cascade_high_mpic(struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
+	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+
+	if (chip->irq_eoi)
+		chip->irq_eoi(&desc->irq_data);
+}
+
+static void qe_ic_cascade_muxed_mpic(struct irq_desc *desc)
+{
+	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
+	unsigned int cascade_irq;
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+
+	cascade_irq = qe_ic_get_high_irq(qe_ic);
+	if (cascade_irq == NO_IRQ)
+		cascade_irq = qe_ic_get_low_irq(qe_ic);
+
+	if (cascade_irq != NO_IRQ)
+		generic_handle_irq(cascade_irq);
+
+	chip->irq_eoi(&desc->irq_data);
+}
+
 static void __init qe_ic_init(struct device_node *node, unsigned int flags)
 {
 	void (*low_handler)(struct irq_desc *desc);
diff --git a/include/soc/fsl/qe/qe_ic.h b/include/soc/fsl/qe/qe_ic.h
index a47a0d26acbd..43e4ce95c6a0 100644
--- a/include/soc/fsl/qe/qe_ic.h
+++ b/include/soc/fsl/qe/qe_ic.h
@@ -67,46 +67,4 @@ void qe_ic_set_highest_priority(unsigned int virq, int high);
 int qe_ic_set_priority(unsigned int virq, unsigned int priority);
 int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high);
 
-static inline void qe_ic_cascade_low_mpic(struct irq_desc *desc)
-{
-	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
-	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
-	struct irq_chip *chip = irq_desc_get_chip(desc);
-
-	if (cascade_irq != NO_IRQ)
-		generic_handle_irq(cascade_irq);
-
-	if (chip->irq_eoi)
-		chip->irq_eoi(&desc->irq_data);
-}
-
-static inline void qe_ic_cascade_high_mpic(struct irq_desc *desc)
-{
-	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
-	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
-	struct irq_chip *chip = irq_desc_get_chip(desc);
-
-	if (cascade_irq != NO_IRQ)
-		generic_handle_irq(cascade_irq);
-
-	if (chip->irq_eoi)
-		chip->irq_eoi(&desc->irq_data);
-}
-
-static inline void qe_ic_cascade_muxed_mpic(struct irq_desc *desc)
-{
-	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
-	unsigned int cascade_irq;
-	struct irq_chip *chip = irq_desc_get_chip(desc);
-
-	cascade_irq = qe_ic_get_high_irq(qe_ic);
-	if (cascade_irq == NO_IRQ)
-		cascade_irq = qe_ic_get_low_irq(qe_ic);
-
-	if (cascade_irq != NO_IRQ)
-		generic_handle_irq(cascade_irq);
-
-	chip->irq_eoi(&desc->irq_data);
-}
-
 #endif /* _ASM_POWERPC_QE_IC_H */
-- 
2.23.0

[PATCH v6 16/49] soc: fsl: qe: rename qe_ic_cascade_low_mpic -> qe_ic_cascade_low

[Rasmus Villemoes]

The qe_ic_cascade_{low,high}_mpic functions are now used as handlers
both when the interrupt parent is mpic as well as ipic, so remove the
_mpic suffix.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 94ccbeeb1ad1..de2ca2e3a648 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -314,7 +314,7 @@ unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 	return irq_linear_revmap(qe_ic->irqhost, irq);
 }
 
-static void qe_ic_cascade_low_mpic(struct irq_desc *desc)
+static void qe_ic_cascade_low(struct irq_desc *desc)
 {
 	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
 	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
@@ -327,7 +327,7 @@ static void qe_ic_cascade_low_mpic(struct irq_desc *desc)
 		chip->irq_eoi(&desc->irq_data);
 }
 
-static void qe_ic_cascade_high_mpic(struct irq_desc *desc)
+static void qe_ic_cascade_high(struct irq_desc *desc)
 {
 	struct qe_ic *qe_ic = irq_desc_get_handler_data(desc);
 	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
@@ -392,8 +392,8 @@ static void __init qe_ic_init(struct device_node *node, unsigned int flags)
 		return;
 	}
 	if (qe_ic->virq_high != qe_ic->virq_low) {
-		low_handler = qe_ic_cascade_low_mpic;
-		high_handler = qe_ic_cascade_high_mpic;
+		low_handler = qe_ic_cascade_low;
+		high_handler = qe_ic_cascade_high;
 	} else {
 		low_handler = qe_ic_cascade_muxed_mpic;
 		high_handler = NULL;
-- 
2.23.0

[PATCH v6 17/49] soc: fsl: qe: remove unused qe_ic_set_* functions

[Rasmus Villemoes]

There are no current callers of these functions, and they use the
ppc-specific virq_to_hw(). So removing them gets us one step closer to
building QE support for ARM.

If the functionality is ever actually needed, the code can be dug out
of git and then adapted to work on all architectures, but for future
reference please note that I believe qe_ic_set_priority is buggy: The
"priority < 4" should be "priority <= 4", and in the else branch 24
should be replaced by 28, at least if I'm reading the data sheet right.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 94 --------------------------------------
 include/soc/fsl/qe/qe_ic.h |  4 --
 2 files changed, 98 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index de2ca2e3a648..4839dcd5c5d3 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -445,97 +445,3 @@ static int __init qe_ic_of_init(void)
 	return 0;
 }
 subsys_initcall(qe_ic_of_init);
-
-void qe_ic_set_highest_priority(unsigned int virq, int high)
-{
-	struct qe_ic *qe_ic = qe_ic_from_irq(virq);
-	unsigned int src = virq_to_hw(virq);
-	u32 temp = 0;
-
-	temp = qe_ic_read(qe_ic->regs, QEIC_CICR);
-
-	temp &= ~CICR_HP_MASK;
-	temp |= src << CICR_HP_SHIFT;
-
-	temp &= ~CICR_HPIT_MASK;
-	temp |= (high ? SIGNAL_HIGH : SIGNAL_LOW) << CICR_HPIT_SHIFT;
-
-	qe_ic_write(qe_ic->regs, QEIC_CICR, temp);
-}
-
-/* Set Priority level within its group, from 1 to 8 */
-int qe_ic_set_priority(unsigned int virq, unsigned int priority)
-{
-	struct qe_ic *qe_ic = qe_ic_from_irq(virq);
-	unsigned int src = virq_to_hw(virq);
-	u32 temp;
-
-	if (priority > 8 || priority == 0)
-		return -EINVAL;
-	if (WARN_ONCE(src >= ARRAY_SIZE(qe_ic_info),
-		      "%s: Invalid hw irq number for QEIC\n", __func__))
-		return -EINVAL;
-	if (qe_ic_info[src].pri_reg == 0)
-		return -EINVAL;
-
-	temp = qe_ic_read(qe_ic->regs, qe_ic_info[src].pri_reg);
-
-	if (priority < 4) {
-		temp &= ~(0x7 << (32 - priority * 3));
-		temp |= qe_ic_info[src].pri_code << (32 - priority * 3);
-	} else {
-		temp &= ~(0x7 << (24 - priority * 3));
-		temp |= qe_ic_info[src].pri_code << (24 - priority * 3);
-	}
-
-	qe_ic_write(qe_ic->regs, qe_ic_info[src].pri_reg, temp);
-
-	return 0;
-}
-
-/* Set a QE priority to use high irq, only priority 1~2 can use high irq */
-int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high)
-{
-	struct qe_ic *qe_ic = qe_ic_from_irq(virq);
-	unsigned int src = virq_to_hw(virq);
-	u32 temp, control_reg = QEIC_CICNR, shift = 0;
-
-	if (priority > 2 || priority == 0)
-		return -EINVAL;
-	if (WARN_ONCE(src >= ARRAY_SIZE(qe_ic_info),
-		      "%s: Invalid hw irq number for QEIC\n", __func__))
-		return -EINVAL;
-
-	switch (qe_ic_info[src].pri_reg) {
-	case QEIC_CIPZCC:
-		shift = CICNR_ZCC1T_SHIFT;
-		break;
-	case QEIC_CIPWCC:
-		shift = CICNR_WCC1T_SHIFT;
-		break;
-	case QEIC_CIPYCC:
-		shift = CICNR_YCC1T_SHIFT;
-		break;
-	case QEIC_CIPXCC:
-		shift = CICNR_XCC1T_SHIFT;
-		break;
-	case QEIC_CIPRTA:
-		shift = CRICR_RTA1T_SHIFT;
-		control_reg = QEIC_CRICR;
-		break;
-	case QEIC_CIPRTB:
-		shift = CRICR_RTB1T_SHIFT;
-		control_reg = QEIC_CRICR;
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	shift += (2 - priority) * 2;
-	temp = qe_ic_read(qe_ic->regs, control_reg);
-	temp &= ~(SIGNAL_MASK << shift);
-	temp |= (high ? SIGNAL_HIGH : SIGNAL_LOW) << shift;
-	qe_ic_write(qe_ic->regs, control_reg, temp);
-
-	return 0;
-}
diff --git a/include/soc/fsl/qe/qe_ic.h b/include/soc/fsl/qe/qe_ic.h
index 43e4ce95c6a0..d47eb231519e 100644
--- a/include/soc/fsl/qe/qe_ic.h
+++ b/include/soc/fsl/qe/qe_ic.h
@@ -63,8 +63,4 @@ static inline unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 { return 0; }
 #endif /* CONFIG_QUICC_ENGINE */
 
-void qe_ic_set_highest_priority(unsigned int virq, int high);
-int qe_ic_set_priority(unsigned int virq, unsigned int priority);
-int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high);
-
 #endif /* _ASM_POWERPC_QE_IC_H */
-- 
2.23.0

[PATCH v6 18/49] soc: fsl: qe: don't use NO_IRQ in qe_ic.c

[Rasmus Villemoes]

This driver is currently PPC-only, and on powerpc, NO_IRQ is 0, so
this doesn't change functionality. However, not every architecture
defines NO_IRQ, and some define it as -1, so the detection of a failed
irq_of_parse_and_map() (which returns 0 on failure) would be wrong on
those. So to prepare for allowing this driver to build on other
architectures, drop all references to NO_IRQ.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 4839dcd5c5d3..8f74bc6efd5c 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -282,7 +282,7 @@ static const struct irq_domain_ops qe_ic_host_ops = {
 	.xlate = irq_domain_xlate_onetwocell,
 };
 
-/* Return an interrupt vector or NO_IRQ if no interrupt is pending. */
+/* Return an interrupt vector or 0 if no interrupt is pending. */
 unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
 {
 	int irq;
@@ -293,12 +293,12 @@ unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
 	irq = qe_ic_read(qe_ic->regs, QEIC_CIVEC) >> 26;
 
 	if (irq == 0)
-		return NO_IRQ;
+		return 0;
 
 	return irq_linear_revmap(qe_ic->irqhost, irq);
 }
 
-/* Return an interrupt vector or NO_IRQ if no interrupt is pending. */
+/* Return an interrupt vector or 0 if no interrupt is pending. */
 unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 {
 	int irq;
@@ -309,7 +309,7 @@ unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 	irq = qe_ic_read(qe_ic->regs, QEIC_CHIVEC) >> 26;
 
 	if (irq == 0)
-		return NO_IRQ;
+		return 0;
 
 	return irq_linear_revmap(qe_ic->irqhost, irq);
 }
@@ -320,7 +320,7 @@ static void qe_ic_cascade_low(struct irq_desc *desc)
 	unsigned int cascade_irq = qe_ic_get_low_irq(qe_ic);
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 
-	if (cascade_irq != NO_IRQ)
+	if (cascade_irq != 0)
 		generic_handle_irq(cascade_irq);
 
 	if (chip->irq_eoi)
@@ -333,7 +333,7 @@ static void qe_ic_cascade_high(struct irq_desc *desc)
 	unsigned int cascade_irq = qe_ic_get_high_irq(qe_ic);
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 
-	if (cascade_irq != NO_IRQ)
+	if (cascade_irq != 0)
 		generic_handle_irq(cascade_irq);
 
 	if (chip->irq_eoi)
@@ -347,10 +347,10 @@ static void qe_ic_cascade_muxed_mpic(struct irq_desc *desc)
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 
 	cascade_irq = qe_ic_get_high_irq(qe_ic);
-	if (cascade_irq == NO_IRQ)
+	if (cascade_irq == 0)
 		cascade_irq = qe_ic_get_low_irq(qe_ic);
 
-	if (cascade_irq != NO_IRQ)
+	if (cascade_irq != 0)
 		generic_handle_irq(cascade_irq);
 
 	chip->irq_eoi(&desc->irq_data);
@@ -386,7 +386,7 @@ static void __init qe_ic_init(struct device_node *node, unsigned int flags)
 	qe_ic->virq_high = irq_of_parse_and_map(node, 0);
 	qe_ic->virq_low = irq_of_parse_and_map(node, 1);
 
-	if (qe_ic->virq_low == NO_IRQ) {
+	if (!qe_ic->virq_low) {
 		printk(KERN_ERR "Failed to map QE_IC low IRQ\n");
 		kfree(qe_ic);
 		return;
@@ -423,8 +423,7 @@ static void __init qe_ic_init(struct device_node *node, unsigned int flags)
 	irq_set_handler_data(qe_ic->virq_low, qe_ic);
 	irq_set_chained_handler(qe_ic->virq_low, low_handler);
 
-	if (qe_ic->virq_high != NO_IRQ &&
-			qe_ic->virq_high != qe_ic->virq_low) {
+	if (qe_ic->virq_high && qe_ic->virq_high != qe_ic->virq_low) {
 		irq_set_handler_data(qe_ic->virq_high, qe_ic);
 		irq_set_chained_handler(qe_ic->virq_high, high_handler);
 	}
-- 
2.23.0

[PATCH v6 19/49] soc: fsl: qe: make qe_ic_get_{low,high}_irq static

[Rasmus Villemoes]

These are only called from within qe_ic.c, so make them static.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c |  4 ++--
 include/soc/fsl/qe/qe_ic.h | 10 ----------
 2 files changed, 2 insertions(+), 12 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 8f74bc6efd5c..23b457e884d8 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -283,7 +283,7 @@ static const struct irq_domain_ops qe_ic_host_ops = {
 };
 
 /* Return an interrupt vector or 0 if no interrupt is pending. */
-unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
+static unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
 {
 	int irq;
 
@@ -299,7 +299,7 @@ unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
 }
 
 /* Return an interrupt vector or 0 if no interrupt is pending. */
-unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
+static unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
 {
 	int irq;
 
diff --git a/include/soc/fsl/qe/qe_ic.h b/include/soc/fsl/qe/qe_ic.h
index d47eb231519e..70bb5a0f6535 100644
--- a/include/soc/fsl/qe/qe_ic.h
+++ b/include/soc/fsl/qe/qe_ic.h
@@ -53,14 +53,4 @@ enum qe_ic_grp_id {
 	QE_IC_GRP_RISCB		/* QE interrupt controller RISC group B */
 };
 
-#ifdef CONFIG_QUICC_ENGINE
-unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
-unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
-#else
-static inline unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
-{ return 0; }
-static inline unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
-{ return 0; }
-#endif /* CONFIG_QUICC_ENGINE */
-
 #endif /* _ASM_POWERPC_QE_IC_H */
-- 
2.23.0

[PATCH v6 20/49] soc: fsl: qe: simplify qe_ic_init()

[Rasmus Villemoes]

qe_ic_init() takes a flags parameter, but all callers (including the
sole remaining one) have always passed 0. So remove that parameter and
simplify the body accordingly. We still explicitly initialize the
Interrupt Configuration Register (CICR) to its reset value of
all-zeroes, just in case the bootloader has played funny games.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 27 ++++-----------------------
 1 file changed, 4 insertions(+), 23 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 23b457e884d8..4832884da5bb 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -356,13 +356,13 @@ static void qe_ic_cascade_muxed_mpic(struct irq_desc *desc)
 	chip->irq_eoi(&desc->irq_data);
 }
 
-static void __init qe_ic_init(struct device_node *node, unsigned int flags)
+static void __init qe_ic_init(struct device_node *node)
 {
 	void (*low_handler)(struct irq_desc *desc);
 	void (*high_handler)(struct irq_desc *desc);
 	struct qe_ic *qe_ic;
 	struct resource res;
-	u32 temp = 0, ret;
+	u32 ret;
 
 	ret = of_address_to_resource(node, 0, &res);
 	if (ret)
@@ -399,26 +399,7 @@ static void __init qe_ic_init(struct device_node *node, unsigned int flags)
 		high_handler = NULL;
 	}
 
-	/* default priority scheme is grouped. If spread mode is    */
-	/* required, configure cicr accordingly.                    */
-	if (flags & QE_IC_SPREADMODE_GRP_W)
-		temp |= CICR_GWCC;
-	if (flags & QE_IC_SPREADMODE_GRP_X)
-		temp |= CICR_GXCC;
-	if (flags & QE_IC_SPREADMODE_GRP_Y)
-		temp |= CICR_GYCC;
-	if (flags & QE_IC_SPREADMODE_GRP_Z)
-		temp |= CICR_GZCC;
-	if (flags & QE_IC_SPREADMODE_GRP_RISCA)
-		temp |= CICR_GRTA;
-	if (flags & QE_IC_SPREADMODE_GRP_RISCB)
-		temp |= CICR_GRTB;
-
-	/* choose destination signal for highest priority interrupt */
-	if (flags & QE_IC_HIGH_SIGNAL)
-		temp |= (SIGNAL_HIGH << CICR_HPIT_SHIFT);
-
-	qe_ic_write(qe_ic->regs, QEIC_CICR, temp);
+	qe_ic_write(qe_ic->regs, QEIC_CICR, 0);
 
 	irq_set_handler_data(qe_ic->virq_low, qe_ic);
 	irq_set_chained_handler(qe_ic->virq_low, low_handler);
@@ -439,7 +420,7 @@ static int __init qe_ic_of_init(void)
 		if (!np)
 			return -ENODEV;
 	}
-	qe_ic_init(np, 0);
+	qe_ic_init(np);
 	of_node_put(np);
 	return 0;
 }
-- 
2.23.0

[PATCH v6 21/49] soc: fsl: qe: merge qe_ic.h headers into qe_ic.c

[Rasmus Villemoes]

The public qe_ic.h header is no longer included by anything but
qe_ic.c. Merge both headers into qe_ic.c, and drop the unused
constants.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_ic.c | 52 +++++++++++++++++++-
 drivers/soc/fsl/qe/qe_ic.h | 99 --------------------------------------
 include/soc/fsl/qe/qe_ic.h | 56 ---------------------
 3 files changed, 50 insertions(+), 157 deletions(-)
 delete mode 100644 drivers/soc/fsl/qe/qe_ic.h
 delete mode 100644 include/soc/fsl/qe/qe_ic.h

diff --git a/drivers/soc/fsl/qe/qe_ic.c b/drivers/soc/fsl/qe/qe_ic.c
index 4832884da5bb..0dd5bdb04a14 100644
--- a/drivers/soc/fsl/qe/qe_ic.c
+++ b/drivers/soc/fsl/qe/qe_ic.c
@@ -15,6 +15,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/errno.h>
+#include <linux/irq.h>
 #include <linux/reboot.h>
 #include <linux/slab.h>
 #include <linux/stddef.h>
@@ -25,9 +26,56 @@
 #include <asm/irq.h>
 #include <asm/io.h>
 #include <soc/fsl/qe/qe.h>
-#include <soc/fsl/qe/qe_ic.h>
 
-#include "qe_ic.h"
+#define NR_QE_IC_INTS		64
+
+/* QE IC registers offset */
+#define QEIC_CICR		0x00
+#define QEIC_CIVEC		0x04
+#define QEIC_CIPXCC		0x10
+#define QEIC_CIPYCC		0x14
+#define QEIC_CIPWCC		0x18
+#define QEIC_CIPZCC		0x1c
+#define QEIC_CIMR		0x20
+#define QEIC_CRIMR		0x24
+#define QEIC_CIPRTA		0x30
+#define QEIC_CIPRTB		0x34
+#define QEIC_CHIVEC		0x60
+
+struct qe_ic {
+	/* Control registers offset */
+	u32 __iomem *regs;
+
+	/* The remapper for this QEIC */
+	struct irq_domain *irqhost;
+
+	/* The "linux" controller struct */
+	struct irq_chip hc_irq;
+
+	/* VIRQ numbers of QE high/low irqs */
+	unsigned int virq_high;
+	unsigned int virq_low;
+};
+
+/*
+ * QE interrupt controller internal structure
+ */
+struct qe_ic_info {
+	/* Location of this source at the QIMR register */
+	u32	mask;
+
+	/* Mask register offset */
+	u32	mask_reg;
+
+	/*
+	 * For grouped interrupts sources - the interrupt code as
+	 * appears at the group priority register
+	 */
+	u8	pri_code;
+
+	/* Group priority register offset */
+	u32	pri_reg;
+};
 
 static DEFINE_RAW_SPINLOCK(qe_ic_lock);
 
diff --git a/drivers/soc/fsl/qe/qe_ic.h b/drivers/soc/fsl/qe/qe_ic.h
deleted file mode 100644
index 9420378d9b6b..000000000000
--- a/drivers/soc/fsl/qe/qe_ic.h
+++ /dev/null
@@ -1,99 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * drivers/soc/fsl/qe/qe_ic.h
- *
- * QUICC ENGINE Interrupt Controller Header
- *
- * Copyright (C) 2006 Freescale Semiconductor, Inc. All rights reserved.
- *
- * Author: Li Yang <leoli@freescale.com>
- * Based on code from Shlomi Gridish <gridish@freescale.com>
- */
-#ifndef _POWERPC_SYSDEV_QE_IC_H
-#define _POWERPC_SYSDEV_QE_IC_H
-
-#include <soc/fsl/qe/qe_ic.h>
-
-#define NR_QE_IC_INTS		64
-
-/* QE IC registers offset */
-#define QEIC_CICR		0x00
-#define QEIC_CIVEC		0x04
-#define QEIC_CRIPNR		0x08
-#define QEIC_CIPNR		0x0c
-#define QEIC_CIPXCC		0x10
-#define QEIC_CIPYCC		0x14
-#define QEIC_CIPWCC		0x18
-#define QEIC_CIPZCC		0x1c
-#define QEIC_CIMR		0x20
-#define QEIC_CRIMR		0x24
-#define QEIC_CICNR		0x28
-#define QEIC_CIPRTA		0x30
-#define QEIC_CIPRTB		0x34
-#define QEIC_CRICR		0x3c
-#define QEIC_CHIVEC		0x60
-
-/* Interrupt priority registers */
-#define CIPCC_SHIFT_PRI0	29
-#define CIPCC_SHIFT_PRI1	26
-#define CIPCC_SHIFT_PRI2	23
-#define CIPCC_SHIFT_PRI3	20
-#define CIPCC_SHIFT_PRI4	13
-#define CIPCC_SHIFT_PRI5	10
-#define CIPCC_SHIFT_PRI6	7
-#define CIPCC_SHIFT_PRI7	4
-
-/* CICR priority modes */
-#define CICR_GWCC		0x00040000
-#define CICR_GXCC		0x00020000
-#define CICR_GYCC		0x00010000
-#define CICR_GZCC		0x00080000
-#define CICR_GRTA		0x00200000
-#define CICR_GRTB		0x00400000
-#define CICR_HPIT_SHIFT		8
-#define CICR_HPIT_MASK		0x00000300
-#define CICR_HP_SHIFT		24
-#define CICR_HP_MASK		0x3f000000
-
-/* CICNR */
-#define CICNR_WCC1T_SHIFT	20
-#define CICNR_ZCC1T_SHIFT	28
-#define CICNR_YCC1T_SHIFT	12
-#define CICNR_XCC1T_SHIFT	4
-
-/* CRICR */
-#define CRICR_RTA1T_SHIFT	20
-#define CRICR_RTB1T_SHIFT	28
-
-/* Signal indicator */
-#define SIGNAL_MASK		3
-#define SIGNAL_HIGH		2
-#define SIGNAL_LOW		0
-
-struct qe_ic {
-	/* Control registers offset */
-	u32 __iomem *regs;
-
-	/* The remapper for this QEIC */
-	struct irq_domain *irqhost;
-
-	/* The "linux" controller struct */
-	struct irq_chip hc_irq;
-
-	/* VIRQ numbers of QE high/low irqs */
-	unsigned int virq_high;
-	unsigned int virq_low;
-};
-
-/*
- * QE interrupt controller internal structure
- */
-struct qe_ic_info {
-	u32	mask;	  /* location of this source at the QIMR register. */
-	u32	mask_reg; /* Mask register offset */
-	u8	pri_code; /* for grouped interrupts sources - the interrupt
-			     code as appears at the group priority register */
-	u32	pri_reg;  /* Group priority register offset */
-};
-
-#endif /* _POWERPC_SYSDEV_QE_IC_H */
diff --git a/include/soc/fsl/qe/qe_ic.h b/include/soc/fsl/qe/qe_ic.h
deleted file mode 100644
index 70bb5a0f6535..000000000000
--- a/include/soc/fsl/qe/qe_ic.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc. All rights reserved.
- *
- * Authors: 	Shlomi Gridish <gridish@freescale.com>
- * 		Li Yang <leoli@freescale.com>
- *
- * Description:
- * QE IC external definitions and structure.
- */
-#ifndef _ASM_POWERPC_QE_IC_H
-#define _ASM_POWERPC_QE_IC_H
-
-#include <linux/irq.h>
-
-struct device_node;
-struct qe_ic;
-
-#define NUM_OF_QE_IC_GROUPS	6
-
-/* Flags when we init the QE IC */
-#define QE_IC_SPREADMODE_GRP_W			0x00000001
-#define QE_IC_SPREADMODE_GRP_X			0x00000002
-#define QE_IC_SPREADMODE_GRP_Y			0x00000004
-#define QE_IC_SPREADMODE_GRP_Z			0x00000008
-#define QE_IC_SPREADMODE_GRP_RISCA		0x00000010
-#define QE_IC_SPREADMODE_GRP_RISCB		0x00000020
-
-#define QE_IC_LOW_SIGNAL			0x00000100
-#define QE_IC_HIGH_SIGNAL			0x00000200
-
-#define QE_IC_GRP_W_PRI0_DEST_SIGNAL_HIGH	0x00001000
-#define QE_IC_GRP_W_PRI1_DEST_SIGNAL_HIGH	0x00002000
-#define QE_IC_GRP_X_PRI0_DEST_SIGNAL_HIGH	0x00004000
-#define QE_IC_GRP_X_PRI1_DEST_SIGNAL_HIGH	0x00008000
-#define QE_IC_GRP_Y_PRI0_DEST_SIGNAL_HIGH	0x00010000
-#define QE_IC_GRP_Y_PRI1_DEST_SIGNAL_HIGH	0x00020000
-#define QE_IC_GRP_Z_PRI0_DEST_SIGNAL_HIGH	0x00040000
-#define QE_IC_GRP_Z_PRI1_DEST_SIGNAL_HIGH	0x00080000
-#define QE_IC_GRP_RISCA_PRI0_DEST_SIGNAL_HIGH	0x00100000
-#define QE_IC_GRP_RISCA_PRI1_DEST_SIGNAL_HIGH	0x00200000
-#define QE_IC_GRP_RISCB_PRI0_DEST_SIGNAL_HIGH	0x00400000
-#define QE_IC_GRP_RISCB_PRI1_DEST_SIGNAL_HIGH	0x00800000
-#define QE_IC_GRP_W_DEST_SIGNAL_SHIFT		(12)
-
-/* QE interrupt sources groups */
-enum qe_ic_grp_id {
-	QE_IC_GRP_W = 0,	/* QE interrupt controller group W */
-	QE_IC_GRP_X,		/* QE interrupt controller group X */
-	QE_IC_GRP_Y,		/* QE interrupt controller group Y */
-	QE_IC_GRP_Z,		/* QE interrupt controller group Z */
-	QE_IC_GRP_RISCA,	/* QE interrupt controller RISC group A */
-	QE_IC_GRP_RISCB		/* QE interrupt controller RISC group B */
-};
-
-#endif /* _ASM_POWERPC_QE_IC_H */
-- 
2.23.0

[PATCH v6 22/49] soc: fsl: qe: qe.c: use of_property_read_* helpers

[Rasmus Villemoes]

Instead of manually doing of_get_property/of_find_property and reading
the value by assigning to a u32* or u64* and dereferencing, use the
of_property_read_* functions.

This make the code more readable, and more importantly, is required
for this to work correctly on little-endian platforms.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c | 33 ++++++++-------------------------
 1 file changed, 8 insertions(+), 25 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index a4763282ea68..ec511840db3c 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -159,8 +159,7 @@ static unsigned int brg_clk = 0;
 unsigned int qe_get_brg_clk(void)
 {
 	struct device_node *qe;
-	int size;
-	const u32 *prop;
+	u32 brg;
 	unsigned int mod;
 
 	if (brg_clk)
@@ -170,9 +169,8 @@ unsigned int qe_get_brg_clk(void)
 	if (!qe)
 		return brg_clk;
 
-	prop = of_get_property(qe, "brg-frequency", &size);
-	if (prop && size == sizeof(*prop))
-		brg_clk = *prop;
+	if (!of_property_read_u32(qe, "brg-frequency", &brg))
+		brg_clk = brg;
 
 	of_node_put(qe);
 
@@ -571,11 +569,9 @@ EXPORT_SYMBOL(qe_upload_firmware);
 struct qe_firmware_info *qe_get_firmware_info(void)
 {
 	static int initialized;
-	struct property *prop;
 	struct device_node *qe;
 	struct device_node *fw = NULL;
 	const char *sprop;
-	unsigned int i;
 
 	/*
 	 * If we haven't checked yet, and a driver hasn't uploaded a firmware
@@ -609,20 +605,11 @@ struct qe_firmware_info *qe_get_firmware_info(void)
 		strlcpy(qe_firmware_info.id, sprop,
 			sizeof(qe_firmware_info.id));
 
-	prop = of_find_property(fw, "extended-modes", NULL);
-	if (prop && (prop->length == sizeof(u64))) {
-		const u64 *iprop = prop->value;
-
-		qe_firmware_info.extended_modes = *iprop;
-	}
+	of_property_read_u64(fw, "extended-modes",
+			     &qe_firmware_info.extended_modes);
 
-	prop = of_find_property(fw, "virtual-traps", NULL);
-	if (prop && (prop->length == 32)) {
-		const u32 *iprop = prop->value;
-
-		for (i = 0; i < ARRAY_SIZE(qe_firmware_info.vtraps); i++)
-			qe_firmware_info.vtraps[i] = iprop[i];
-	}
+	of_property_read_u32_array(fw, "virtual-traps", qe_firmware_info.vtraps,
+				   ARRAY_SIZE(qe_firmware_info.vtraps));
 
 	of_node_put(fw);
 
@@ -633,17 +620,13 @@ EXPORT_SYMBOL(qe_get_firmware_info);
 unsigned int qe_get_num_of_risc(void)
 {
 	struct device_node *qe;
-	int size;
 	unsigned int num_of_risc = 0;
-	const u32 *prop;
 
 	qe = qe_get_device_node();
 	if (!qe)
 		return num_of_risc;
 
-	prop = of_get_property(qe, "fsl,qe-num-riscs", &size);
-	if (prop && size == sizeof(*prop))
-		num_of_risc = *prop;
+	of_property_read_u32(qe, "fsl,qe-num-riscs", &num_of_risc);
 
 	of_node_put(qe);
 
-- 
2.23.0

[PATCH v6 23/49] soc: fsl: qe: qe_io.c: don't open-code of_parse_phandle()

[Rasmus Villemoes]

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_io.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_io.c b/drivers/soc/fsl/qe/qe_io.c
index f6b10f38b2f4..99aeb01586bd 100644
--- a/drivers/soc/fsl/qe/qe_io.c
+++ b/drivers/soc/fsl/qe/qe_io.c
@@ -141,7 +141,6 @@ EXPORT_SYMBOL(par_io_data_set);
 int par_io_of_config(struct device_node *np)
 {
 	struct device_node *pio;
-	const phandle *ph;
 	int pio_map_len;
 	const unsigned int *pio_map;
 
@@ -150,14 +149,12 @@ int par_io_of_config(struct device_node *np)
 		return -1;
 	}
 
-	ph = of_get_property(np, "pio-handle", NULL);
-	if (ph == NULL) {
+	pio = of_parse_phandle(np, "pio-handle", 0);
+	if (pio == NULL) {
 		printk(KERN_ERR "pio-handle not available\n");
 		return -1;
 	}
 
-	pio = of_find_node_by_phandle(*ph);
-
 	pio_map = of_get_property(pio, "pio-map", &pio_map_len);
 	if (pio_map == NULL) {
 		printk(KERN_ERR "pio-map is not set!\n");
-- 
2.23.0

[PATCH v6 24/49] soc: fsl: qe: qe_io.c: access device tree property using be32_to_cpu

[Rasmus Villemoes]

We need to apply be32_to_cpu to make this work correctly on
little-endian hosts.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_io.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_io.c b/drivers/soc/fsl/qe/qe_io.c
index 99aeb01586bd..61dd8eb8c0fe 100644
--- a/drivers/soc/fsl/qe/qe_io.c
+++ b/drivers/soc/fsl/qe/qe_io.c
@@ -142,7 +142,7 @@ int par_io_of_config(struct device_node *np)
 {
 	struct device_node *pio;
 	int pio_map_len;
-	const unsigned int *pio_map;
+	const __be32 *pio_map;
 
 	if (par_io == NULL) {
 		printk(KERN_ERR "par_io not initialized\n");
@@ -167,9 +167,15 @@ int par_io_of_config(struct device_node *np)
 	}
 
 	while (pio_map_len > 0) {
-		par_io_config_pin((u8) pio_map[0], (u8) pio_map[1],
-				(int) pio_map[2], (int) pio_map[3],
-				(int) pio_map[4], (int) pio_map[5]);
+		u8 port        = be32_to_cpu(pio_map[0]);
+		u8 pin         = be32_to_cpu(pio_map[1]);
+		int dir        = be32_to_cpu(pio_map[2]);
+		int open_drain = be32_to_cpu(pio_map[3]);
+		int assignment = be32_to_cpu(pio_map[4]);
+		int has_irq    = be32_to_cpu(pio_map[5]);
+
+		par_io_config_pin(port, pin, dir, open_drain,
+				  assignment, has_irq);
 		pio_map += 6;
 		pio_map_len -= 6;
 	}
-- 
2.23.0

[PATCH v6 25/49] soc: fsl: qe: qe_io.c: use of_property_read_u32() in par_io_init()

[Rasmus Villemoes]

This is necessary for this to work on little-endian hosts.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_io.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_io.c b/drivers/soc/fsl/qe/qe_io.c
index 61dd8eb8c0fe..11ea08e97db7 100644
--- a/drivers/soc/fsl/qe/qe_io.c
+++ b/drivers/soc/fsl/qe/qe_io.c
@@ -28,7 +28,7 @@ int par_io_init(struct device_node *np)
 {
 	struct resource res;
 	int ret;
-	const u32 *num_ports;
+	u32 num_ports;
 
 	/* Map Parallel I/O ports registers */
 	ret = of_address_to_resource(np, 0, &res);
@@ -36,9 +36,8 @@ int par_io_init(struct device_node *np)
 		return ret;
 	par_io = ioremap(res.start, resource_size(&res));
 
-	num_ports = of_get_property(np, "num-ports", NULL);
-	if (num_ports)
-		num_par_io_ports = *num_ports;
+	if (!of_property_read_u32(np, "num-ports", &num_ports))
+		num_par_io_ports = num_ports;
 
 	return 0;
 }
-- 
2.23.0

[PATCH v6 26/49] soc: fsl: move cpm.h from powerpc/include/asm to include/soc/fsl

[Rasmus Villemoes]

Some drivers, e.g. ucc_uart, need definitions from cpm.h. In order to
allow building those drivers for non-ppc based SOCs, move the header
to include/soc/fsl. For now, leave a trivial wrapper at the old
location so drivers can be updated one by one.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 arch/powerpc/include/asm/cpm.h | 172 +--------------------------------
 include/soc/fsl/cpm.h          | 171 ++++++++++++++++++++++++++++++++
 2 files changed, 172 insertions(+), 171 deletions(-)
 create mode 100644 include/soc/fsl/cpm.h

diff --git a/arch/powerpc/include/asm/cpm.h b/arch/powerpc/include/asm/cpm.h
index 4c24ea8209bb..ce483b0f8a4d 100644
--- a/arch/powerpc/include/asm/cpm.h
+++ b/arch/powerpc/include/asm/cpm.h
@@ -1,171 +1 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __CPM_H
-#define __CPM_H
-
-#include <linux/compiler.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/of.h>
-#include <soc/fsl/qe/qe.h>
-
-/*
- * SPI Parameter RAM common to QE and CPM.
- */
-struct spi_pram {
-	__be16	rbase;	/* Rx Buffer descriptor base address */
-	__be16	tbase;	/* Tx Buffer descriptor base address */
-	u8	rfcr;	/* Rx function code */
-	u8	tfcr;	/* Tx function code */
-	__be16	mrblr;	/* Max receive buffer length */
-	__be32	rstate;	/* Internal */
-	__be32	rdp;	/* Internal */
-	__be16	rbptr;	/* Internal */
-	__be16	rbc;	/* Internal */
-	__be32	rxtmp;	/* Internal */
-	__be32	tstate;	/* Internal */
-	__be32	tdp;	/* Internal */
-	__be16	tbptr;	/* Internal */
-	__be16	tbc;	/* Internal */
-	__be32	txtmp;	/* Internal */
-	__be32	res;	/* Tx temp. */
-	__be16  rpbase;	/* Relocation pointer (CPM1 only) */
-	__be16	res1;	/* Reserved */
-};
-
-/*
- * USB Controller pram common to QE and CPM.
- */
-struct usb_ctlr {
-	u8	usb_usmod;
-	u8	usb_usadr;
-	u8	usb_uscom;
-	u8	res1[1];
-	__be16	usb_usep[4];
-	u8	res2[4];
-	__be16	usb_usber;
-	u8	res3[2];
-	__be16	usb_usbmr;
-	u8	res4[1];
-	u8	usb_usbs;
-	/* Fields down below are QE-only */
-	__be16	usb_ussft;
-	u8	res5[2];
-	__be16	usb_usfrn;
-	u8	res6[0x22];
-} __attribute__ ((packed));
-
-/*
- * Function code bits, usually generic to devices.
- */
-#ifdef CONFIG_CPM1
-#define CPMFCR_GBL	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
-#define CPMFCR_TC2	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
-#define CPMFCR_DTB	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
-#define CPMFCR_BDB	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
-#else
-#define CPMFCR_GBL	((u_char)0x20)	/* Set memory snooping */
-#define CPMFCR_TC2	((u_char)0x04)	/* Transfer code 2 value */
-#define CPMFCR_DTB	((u_char)0x02)	/* Use local bus for data when set */
-#define CPMFCR_BDB	((u_char)0x01)	/* Use local bus for BD when set */
-#endif
-#define CPMFCR_EB	((u_char)0x10)	/* Set big endian byte order */
-
-/* Opcodes common to CPM1 and CPM2
-*/
-#define CPM_CR_INIT_TRX		((ushort)0x0000)
-#define CPM_CR_INIT_RX		((ushort)0x0001)
-#define CPM_CR_INIT_TX		((ushort)0x0002)
-#define CPM_CR_HUNT_MODE	((ushort)0x0003)
-#define CPM_CR_STOP_TX		((ushort)0x0004)
-#define CPM_CR_GRA_STOP_TX	((ushort)0x0005)
-#define CPM_CR_RESTART_TX	((ushort)0x0006)
-#define CPM_CR_CLOSE_RX_BD	((ushort)0x0007)
-#define CPM_CR_SET_GADDR	((ushort)0x0008)
-#define CPM_CR_SET_TIMER	((ushort)0x0008)
-#define CPM_CR_STOP_IDMA	((ushort)0x000b)
-
-/* Buffer descriptors used by many of the CPM protocols. */
-typedef struct cpm_buf_desc {
-	ushort	cbd_sc;		/* Status and Control */
-	ushort	cbd_datlen;	/* Data length in buffer */
-	uint	cbd_bufaddr;	/* Buffer address in host memory */
-} cbd_t;
-
-/* Buffer descriptor control/status used by serial
- */
-
-#define BD_SC_EMPTY	(0x8000)	/* Receive is empty */
-#define BD_SC_READY	(0x8000)	/* Transmit is ready */
-#define BD_SC_WRAP	(0x2000)	/* Last buffer descriptor */
-#define BD_SC_INTRPT	(0x1000)	/* Interrupt on change */
-#define BD_SC_LAST	(0x0800)	/* Last buffer in frame */
-#define BD_SC_TC	(0x0400)	/* Transmit CRC */
-#define BD_SC_CM	(0x0200)	/* Continuous mode */
-#define BD_SC_ID	(0x0100)	/* Rec'd too many idles */
-#define BD_SC_P		(0x0100)	/* xmt preamble */
-#define BD_SC_BR	(0x0020)	/* Break received */
-#define BD_SC_FR	(0x0010)	/* Framing error */
-#define BD_SC_PR	(0x0008)	/* Parity error */
-#define BD_SC_NAK	(0x0004)	/* NAK - did not respond */
-#define BD_SC_OV	(0x0002)	/* Overrun */
-#define BD_SC_UN	(0x0002)	/* Underrun */
-#define BD_SC_CD	(0x0001)	/* */
-#define BD_SC_CL	(0x0001)	/* Collision */
-
-/* Buffer descriptor control/status used by Ethernet receive.
- * Common to SCC and FCC.
- */
-#define BD_ENET_RX_EMPTY	(0x8000)
-#define BD_ENET_RX_WRAP		(0x2000)
-#define BD_ENET_RX_INTR		(0x1000)
-#define BD_ENET_RX_LAST		(0x0800)
-#define BD_ENET_RX_FIRST	(0x0400)
-#define BD_ENET_RX_MISS		(0x0100)
-#define BD_ENET_RX_BC		(0x0080)	/* FCC Only */
-#define BD_ENET_RX_MC		(0x0040)	/* FCC Only */
-#define BD_ENET_RX_LG		(0x0020)
-#define BD_ENET_RX_NO		(0x0010)
-#define BD_ENET_RX_SH		(0x0008)
-#define BD_ENET_RX_CR		(0x0004)
-#define BD_ENET_RX_OV		(0x0002)
-#define BD_ENET_RX_CL		(0x0001)
-#define BD_ENET_RX_STATS	(0x01ff)	/* All status bits */
-
-/* Buffer descriptor control/status used by Ethernet transmit.
- * Common to SCC and FCC.
- */
-#define BD_ENET_TX_READY	(0x8000)
-#define BD_ENET_TX_PAD		(0x4000)
-#define BD_ENET_TX_WRAP		(0x2000)
-#define BD_ENET_TX_INTR		(0x1000)
-#define BD_ENET_TX_LAST		(0x0800)
-#define BD_ENET_TX_TC		(0x0400)
-#define BD_ENET_TX_DEF		(0x0200)
-#define BD_ENET_TX_HB		(0x0100)
-#define BD_ENET_TX_LC		(0x0080)
-#define BD_ENET_TX_RL		(0x0040)
-#define BD_ENET_TX_RCMASK	(0x003c)
-#define BD_ENET_TX_UN		(0x0002)
-#define BD_ENET_TX_CSL		(0x0001)
-#define BD_ENET_TX_STATS	(0x03ff)	/* All status bits */
-
-/* Buffer descriptor control/status used by Transparent mode SCC.
- */
-#define BD_SCC_TX_LAST		(0x0800)
-
-/* Buffer descriptor control/status used by I2C.
- */
-#define BD_I2C_START		(0x0400)
-
-#ifdef CONFIG_CPM
-int cpm_command(u32 command, u8 opcode);
-#else
-static inline int cpm_command(u32 command, u8 opcode)
-{
-	return -ENOSYS;
-}
-#endif /* CONFIG_CPM */
-
-int cpm2_gpiochip_add32(struct device *dev);
-
-#endif
+#include <soc/fsl/cpm.h>
diff --git a/include/soc/fsl/cpm.h b/include/soc/fsl/cpm.h
new file mode 100644
index 000000000000..4c24ea8209bb
--- /dev/null
+++ b/include/soc/fsl/cpm.h
@@ -0,0 +1,171 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __CPM_H
+#define __CPM_H
+
+#include <linux/compiler.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/of.h>
+#include <soc/fsl/qe/qe.h>
+
+/*
+ * SPI Parameter RAM common to QE and CPM.
+ */
+struct spi_pram {
+	__be16	rbase;	/* Rx Buffer descriptor base address */
+	__be16	tbase;	/* Tx Buffer descriptor base address */
+	u8	rfcr;	/* Rx function code */
+	u8	tfcr;	/* Tx function code */
+	__be16	mrblr;	/* Max receive buffer length */
+	__be32	rstate;	/* Internal */
+	__be32	rdp;	/* Internal */
+	__be16	rbptr;	/* Internal */
+	__be16	rbc;	/* Internal */
+	__be32	rxtmp;	/* Internal */
+	__be32	tstate;	/* Internal */
+	__be32	tdp;	/* Internal */
+	__be16	tbptr;	/* Internal */
+	__be16	tbc;	/* Internal */
+	__be32	txtmp;	/* Internal */
+	__be32	res;	/* Tx temp. */
+	__be16  rpbase;	/* Relocation pointer (CPM1 only) */
+	__be16	res1;	/* Reserved */
+};
+
+/*
+ * USB Controller pram common to QE and CPM.
+ */
+struct usb_ctlr {
+	u8	usb_usmod;
+	u8	usb_usadr;
+	u8	usb_uscom;
+	u8	res1[1];
+	__be16	usb_usep[4];
+	u8	res2[4];
+	__be16	usb_usber;
+	u8	res3[2];
+	__be16	usb_usbmr;
+	u8	res4[1];
+	u8	usb_usbs;
+	/* Fields down below are QE-only */
+	__be16	usb_ussft;
+	u8	res5[2];
+	__be16	usb_usfrn;
+	u8	res6[0x22];
+} __attribute__ ((packed));
+
+/*
+ * Function code bits, usually generic to devices.
+ */
+#ifdef CONFIG_CPM1
+#define CPMFCR_GBL	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
+#define CPMFCR_TC2	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
+#define CPMFCR_DTB	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
+#define CPMFCR_BDB	((u_char)0x00)	/* Flag doesn't exist in CPM1 */
+#else
+#define CPMFCR_GBL	((u_char)0x20)	/* Set memory snooping */
+#define CPMFCR_TC2	((u_char)0x04)	/* Transfer code 2 value */
+#define CPMFCR_DTB	((u_char)0x02)	/* Use local bus for data when set */
+#define CPMFCR_BDB	((u_char)0x01)	/* Use local bus for BD when set */
+#endif
+#define CPMFCR_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* Opcodes common to CPM1 and CPM2
+*/
+#define CPM_CR_INIT_TRX		((ushort)0x0000)
+#define CPM_CR_INIT_RX		((ushort)0x0001)
+#define CPM_CR_INIT_TX		((ushort)0x0002)
+#define CPM_CR_HUNT_MODE	((ushort)0x0003)
+#define CPM_CR_STOP_TX		((ushort)0x0004)
+#define CPM_CR_GRA_STOP_TX	((ushort)0x0005)
+#define CPM_CR_RESTART_TX	((ushort)0x0006)
+#define CPM_CR_CLOSE_RX_BD	((ushort)0x0007)
+#define CPM_CR_SET_GADDR	((ushort)0x0008)
+#define CPM_CR_SET_TIMER	((ushort)0x0008)
+#define CPM_CR_STOP_IDMA	((ushort)0x000b)
+
+/* Buffer descriptors used by many of the CPM protocols. */
+typedef struct cpm_buf_desc {
+	ushort	cbd_sc;		/* Status and Control */
+	ushort	cbd_datlen;	/* Data length in buffer */
+	uint	cbd_bufaddr;	/* Buffer address in host memory */
+} cbd_t;
+
+/* Buffer descriptor control/status used by serial
+ */
+
+#define BD_SC_EMPTY	(0x8000)	/* Receive is empty */
+#define BD_SC_READY	(0x8000)	/* Transmit is ready */
+#define BD_SC_WRAP	(0x2000)	/* Last buffer descriptor */
+#define BD_SC_INTRPT	(0x1000)	/* Interrupt on change */
+#define BD_SC_LAST	(0x0800)	/* Last buffer in frame */
+#define BD_SC_TC	(0x0400)	/* Transmit CRC */
+#define BD_SC_CM	(0x0200)	/* Continuous mode */
+#define BD_SC_ID	(0x0100)	/* Rec'd too many idles */
+#define BD_SC_P		(0x0100)	/* xmt preamble */
+#define BD_SC_BR	(0x0020)	/* Break received */
+#define BD_SC_FR	(0x0010)	/* Framing error */
+#define BD_SC_PR	(0x0008)	/* Parity error */
+#define BD_SC_NAK	(0x0004)	/* NAK - did not respond */
+#define BD_SC_OV	(0x0002)	/* Overrun */
+#define BD_SC_UN	(0x0002)	/* Underrun */
+#define BD_SC_CD	(0x0001)	/* */
+#define BD_SC_CL	(0x0001)	/* Collision */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_RX_EMPTY	(0x8000)
+#define BD_ENET_RX_WRAP		(0x2000)
+#define BD_ENET_RX_INTR		(0x1000)
+#define BD_ENET_RX_LAST		(0x0800)
+#define BD_ENET_RX_FIRST	(0x0400)
+#define BD_ENET_RX_MISS		(0x0100)
+#define BD_ENET_RX_BC		(0x0080)	/* FCC Only */
+#define BD_ENET_RX_MC		(0x0040)	/* FCC Only */
+#define BD_ENET_RX_LG		(0x0020)
+#define BD_ENET_RX_NO		(0x0010)
+#define BD_ENET_RX_SH		(0x0008)
+#define BD_ENET_RX_CR		(0x0004)
+#define BD_ENET_RX_OV		(0x0002)
+#define BD_ENET_RX_CL		(0x0001)
+#define BD_ENET_RX_STATS	(0x01ff)	/* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+ * Common to SCC and FCC.
+ */
+#define BD_ENET_TX_READY	(0x8000)
+#define BD_ENET_TX_PAD		(0x4000)
+#define BD_ENET_TX_WRAP		(0x2000)
+#define BD_ENET_TX_INTR		(0x1000)
+#define BD_ENET_TX_LAST		(0x0800)
+#define BD_ENET_TX_TC		(0x0400)
+#define BD_ENET_TX_DEF		(0x0200)
+#define BD_ENET_TX_HB		(0x0100)
+#define BD_ENET_TX_LC		(0x0080)
+#define BD_ENET_TX_RL		(0x0040)
+#define BD_ENET_TX_RCMASK	(0x003c)
+#define BD_ENET_TX_UN		(0x0002)
+#define BD_ENET_TX_CSL		(0x0001)
+#define BD_ENET_TX_STATS	(0x03ff)	/* All status bits */
+
+/* Buffer descriptor control/status used by Transparent mode SCC.
+ */
+#define BD_SCC_TX_LAST		(0x0800)
+
+/* Buffer descriptor control/status used by I2C.
+ */
+#define BD_I2C_START		(0x0400)
+
+#ifdef CONFIG_CPM
+int cpm_command(u32 command, u8 opcode);
+#else
+static inline int cpm_command(u32 command, u8 opcode)
+{
+	return -ENOSYS;
+}
+#endif /* CONFIG_CPM */
+
+int cpm2_gpiochip_add32(struct device *dev);
+
+#endif
-- 
2.23.0

[PATCH v6 27/49] soc/fsl/qe/qe.h: update include path for cpm.h

[Rasmus Villemoes]

asm/cpm.h under arch/powerpc is now just a wrapper for including
soc/fsl/cpm.h. In order to make the qe.h header usable on other
architectures, use the latter path directly.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 include/soc/fsl/qe/qe.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
index 9cac04c692fd..521fa3a177e0 100644
--- a/include/soc/fsl/qe/qe.h
+++ b/include/soc/fsl/qe/qe.h
@@ -17,7 +17,7 @@
 #include <linux/spinlock.h>
 #include <linux/errno.h>
 #include <linux/err.h>
-#include <asm/cpm.h>
+#include <soc/fsl/cpm.h>
 #include <soc/fsl/qe/immap_qe.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-- 
2.23.0

[PATCH v6 28/49] serial: ucc_uart: explicitly include soc/fsl/cpm.h

[Rasmus Villemoes]

This driver uses #defines from soc/fsl/cpm.h, so instead of relying on
some other header pulling that in, do that explicitly. This is
preparation for allowing this driver to build on ARM.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index a0555ae2b1ef..7e802616cba8 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -32,6 +32,7 @@
 #include <soc/fsl/qe/ucc_slow.h>
 
 #include <linux/firmware.h>
+#include <soc/fsl/cpm.h>
 #include <asm/reg.h>
 
 /*
-- 
2.23.0

[PATCH v6 29/49] serial: ucc_uart: replace ppc-specific IO accessors

[Rasmus Villemoes]

Some ARM-based SOCs (e.g. LS1021A) also have a QUICC engine. As
preparation for allowing this driver to build on ARM, replace the
ppc-specific in_be16() etc. by the qe_io* helpers. Done via
coccinelle.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 210 +++++++++++++++++-----------------
 1 file changed, 102 insertions(+), 108 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 7e802616cba8..8a378ee5d34f 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -258,11 +258,11 @@ static unsigned int qe_uart_tx_empty(struct uart_port *port)
 	struct qe_bd *bdp = qe_port->tx_bd_base;
 
 	while (1) {
-		if (in_be16(&bdp->status) & BD_SC_READY)
+		if (qe_ioread16be(&bdp->status) & BD_SC_READY)
 			/* This BD is not done, so return "not done" */
 			return 0;
 
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			/*
 			 * This BD is done and it's the last one, so return
 			 * "done"
@@ -308,7 +308,7 @@ static void qe_uart_stop_tx(struct uart_port *port)
 	struct uart_qe_port *qe_port =
 		container_of(port, struct uart_qe_port, port);
 
-	clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
+	qe_clrbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
 }
 
 /*
@@ -343,10 +343,10 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 		p = qe2cpu_addr(bdp->buf, qe_port);
 
 		*p++ = port->x_char;
-		out_be16(&bdp->length, 1);
-		setbits16(&bdp->status, BD_SC_READY);
+		qe_iowrite16be(1, &bdp->length);
+		qe_setbits_be16(&bdp->status, BD_SC_READY);
 		/* Get next BD. */
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			bdp = qe_port->tx_bd_base;
 		else
 			bdp++;
@@ -365,7 +365,7 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 	/* Pick next descriptor and fill from buffer */
 	bdp = qe_port->tx_cur;
 
-	while (!(in_be16(&bdp->status) & BD_SC_READY) &&
+	while (!(qe_ioread16be(&bdp->status) & BD_SC_READY) &&
 	       (xmit->tail != xmit->head)) {
 		count = 0;
 		p = qe2cpu_addr(bdp->buf, qe_port);
@@ -378,11 +378,11 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 				break;
 		}
 
-		out_be16(&bdp->length, count);
-		setbits16(&bdp->status, BD_SC_READY);
+		qe_iowrite16be(count, &bdp->length);
+		qe_setbits_be16(&bdp->status, BD_SC_READY);
 
 		/* Get next BD. */
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			bdp = qe_port->tx_bd_base;
 		else
 			bdp++;
@@ -415,12 +415,12 @@ static void qe_uart_start_tx(struct uart_port *port)
 		container_of(port, struct uart_qe_port, port);
 
 	/* If we currently are transmitting, then just return */
-	if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
+	if (qe_ioread16be(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
 		return;
 
 	/* Otherwise, pump the port and start transmission */
 	if (qe_uart_tx_pump(qe_port))
-		setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
+		qe_setbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
 }
 
 /*
@@ -431,7 +431,7 @@ static void qe_uart_stop_rx(struct uart_port *port)
 	struct uart_qe_port *qe_port =
 		container_of(port, struct uart_qe_port, port);
 
-	clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
+	qe_clrbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
 }
 
 /* Start or stop sending  break signal
@@ -470,14 +470,14 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port)
 	 */
 	bdp = qe_port->rx_cur;
 	while (1) {
-		status = in_be16(&bdp->status);
+		status = qe_ioread16be(&bdp->status);
 
 		/* If this one is empty, then we assume we've read them all */
 		if (status & BD_SC_EMPTY)
 			break;
 
 		/* get number of characters, and check space in RX buffer */
-		i = in_be16(&bdp->length);
+		i = qe_ioread16be(&bdp->length);
 
 		/* If we don't have enough room in RX buffer for the entire BD,
 		 * then we try later, which will be the next RX interrupt.
@@ -508,9 +508,10 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port)
 		}
 
 		/* This BD is ready to be used again. Clear status. get next */
-		clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR |
-			BD_SC_OV | BD_SC_ID, BD_SC_EMPTY);
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		qe_clrsetbits_be16(&bdp->status,
+				   BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV | BD_SC_ID,
+				   BD_SC_EMPTY);
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			bdp = qe_port->rx_bd_base;
 		else
 			bdp++;
@@ -569,8 +570,8 @@ static irqreturn_t qe_uart_int(int irq, void *data)
 	u16 events;
 
 	/* Clear the interrupts */
-	events = in_be16(&uccp->ucce);
-	out_be16(&uccp->ucce, events);
+	events = qe_ioread16be(&uccp->ucce);
+	qe_iowrite16be(events, &uccp->ucce);
 
 	if (events & UCC_UART_UCCE_BRKE)
 		uart_handle_break(&qe_port->port);
@@ -601,17 +602,17 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port)
 	bdp = qe_port->rx_bd_base;
 	qe_port->rx_cur = qe_port->rx_bd_base;
 	for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) {
-		out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT);
-		out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-		out_be16(&bdp->length, 0);
+		qe_iowrite16be(BD_SC_EMPTY | BD_SC_INTRPT, &bdp->status);
+		qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+		qe_iowrite16be(0, &bdp->length);
 		bd_virt += qe_port->rx_fifosize;
 		bdp++;
 	}
 
 	/* */
-	out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT);
-	out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-	out_be16(&bdp->length, 0);
+	qe_iowrite16be(BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT, &bdp->status);
+	qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+	qe_iowrite16be(0, &bdp->length);
 
 	/* Set the physical address of the host memory
 	 * buffers in the buffer descriptors, and the
@@ -622,21 +623,21 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port)
 	qe_port->tx_cur = qe_port->tx_bd_base;
 	bdp = qe_port->tx_bd_base;
 	for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) {
-		out_be16(&bdp->status, BD_SC_INTRPT);
-		out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-		out_be16(&bdp->length, 0);
+		qe_iowrite16be(BD_SC_INTRPT, &bdp->status);
+		qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+		qe_iowrite16be(0, &bdp->length);
 		bd_virt += qe_port->tx_fifosize;
 		bdp++;
 	}
 
 	/* Loopback requires the preamble bit to be set on the first TX BD */
 #ifdef LOOPBACK
-	setbits16(&qe_port->tx_cur->status, BD_SC_P);
+	qe_setbits_be16(&qe_port->tx_cur->status, BD_SC_P);
 #endif
 
-	out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT);
-	out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-	out_be16(&bdp->length, 0);
+	qe_iowrite16be(BD_SC_WRAP | BD_SC_INTRPT, &bdp->status);
+	qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+	qe_iowrite16be(0, &bdp->length);
 }
 
 /*
@@ -658,78 +659,74 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
 	ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
 
 	/* Program the UCC UART parameter RAM */
-	out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
-	out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
-	out_be16(&uccup->common.mrblr, qe_port->rx_fifosize);
-	out_be16(&uccup->maxidl, 0x10);
-	out_be16(&uccup->brkcr, 1);
-	out_be16(&uccup->parec, 0);
-	out_be16(&uccup->frmec, 0);
-	out_be16(&uccup->nosec, 0);
-	out_be16(&uccup->brkec, 0);
-	out_be16(&uccup->uaddr[0], 0);
-	out_be16(&uccup->uaddr[1], 0);
-	out_be16(&uccup->toseq, 0);
+	qe_iowrite8(UCC_BMR_GBL | UCC_BMR_BO_BE, &uccup->common.rbmr);
+	qe_iowrite8(UCC_BMR_GBL | UCC_BMR_BO_BE, &uccup->common.tbmr);
+	qe_iowrite16be(qe_port->rx_fifosize, &uccup->common.mrblr);
+	qe_iowrite16be(0x10, &uccup->maxidl);
+	qe_iowrite16be(1, &uccup->brkcr);
+	qe_iowrite16be(0, &uccup->parec);
+	qe_iowrite16be(0, &uccup->frmec);
+	qe_iowrite16be(0, &uccup->nosec);
+	qe_iowrite16be(0, &uccup->brkec);
+	qe_iowrite16be(0, &uccup->uaddr[0]);
+	qe_iowrite16be(0, &uccup->uaddr[1]);
+	qe_iowrite16be(0, &uccup->toseq);
 	for (i = 0; i < 8; i++)
-		out_be16(&uccup->cchars[i], 0xC000);
-	out_be16(&uccup->rccm, 0xc0ff);
+		qe_iowrite16be(0xC000, &uccup->cchars[i]);
+	qe_iowrite16be(0xc0ff, &uccup->rccm);
 
 	/* Configure the GUMR registers for UART */
 	if (soft_uart) {
 		/* Soft-UART requires a 1X multiplier for TX */
-		clrsetbits_be32(&uccp->gumr_l,
-			UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
-			UCC_SLOW_GUMR_L_RDCR_MASK,
-			UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 |
-			UCC_SLOW_GUMR_L_RDCR_16);
-
-		clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
-			UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
+		qe_clrsetbits_be32(&uccp->gumr_l,
+				   UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK,
+				   UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 | UCC_SLOW_GUMR_L_RDCR_16);
+
+		qe_clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
+				   UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
 	} else {
-		clrsetbits_be32(&uccp->gumr_l,
-			UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
-			UCC_SLOW_GUMR_L_RDCR_MASK,
-			UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 |
-			UCC_SLOW_GUMR_L_RDCR_16);
-
-		clrsetbits_be32(&uccp->gumr_h,
-			UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
-			UCC_SLOW_GUMR_H_RFW);
+		qe_clrsetbits_be32(&uccp->gumr_l,
+				   UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK,
+				   UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 | UCC_SLOW_GUMR_L_RDCR_16);
+
+		qe_clrsetbits_be32(&uccp->gumr_h,
+				   UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
+				   UCC_SLOW_GUMR_H_RFW);
 	}
 
 #ifdef LOOPBACK
-	clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
-		UCC_SLOW_GUMR_L_DIAG_LOOP);
-	clrsetbits_be32(&uccp->gumr_h,
-		UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
-		UCC_SLOW_GUMR_H_CDS);
+	qe_clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
+			   UCC_SLOW_GUMR_L_DIAG_LOOP);
+	qe_clrsetbits_be32(&uccp->gumr_h,
+			   UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
+			   UCC_SLOW_GUMR_H_CDS);
 #endif
 
 	/* Disable rx interrupts  and clear all pending events.  */
-	out_be16(&uccp->uccm, 0);
-	out_be16(&uccp->ucce, 0xffff);
-	out_be16(&uccp->udsr, 0x7e7e);
+	qe_iowrite16be(0, &uccp->uccm);
+	qe_iowrite16be(0xffff, &uccp->ucce);
+	qe_iowrite16be(0x7e7e, &uccp->udsr);
 
 	/* Initialize UPSMR */
-	out_be16(&uccp->upsmr, 0);
+	qe_iowrite16be(0, &uccp->upsmr);
 
 	if (soft_uart) {
-		out_be16(&uccup->supsmr, 0x30);
-		out_be16(&uccup->res92, 0);
-		out_be32(&uccup->rx_state, 0);
-		out_be32(&uccup->rx_cnt, 0);
-		out_8(&uccup->rx_bitmark, 0);
-		out_8(&uccup->rx_length, 10);
-		out_be32(&uccup->dump_ptr, 0x4000);
-		out_8(&uccup->rx_temp_dlst_qe, 0);
-		out_be32(&uccup->rx_frame_rem, 0);
-		out_8(&uccup->rx_frame_rem_size, 0);
+		qe_iowrite16be(0x30, &uccup->supsmr);
+		qe_iowrite16be(0, &uccup->res92);
+		qe_iowrite32be(0, &uccup->rx_state);
+		qe_iowrite32be(0, &uccup->rx_cnt);
+		qe_iowrite8(0, &uccup->rx_bitmark);
+		qe_iowrite8(10, &uccup->rx_length);
+		qe_iowrite32be(0x4000, &uccup->dump_ptr);
+		qe_iowrite8(0, &uccup->rx_temp_dlst_qe);
+		qe_iowrite32be(0, &uccup->rx_frame_rem);
+		qe_iowrite8(0, &uccup->rx_frame_rem_size);
 		/* Soft-UART requires TX to be 1X */
-		out_8(&uccup->tx_mode,
-			UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1);
-		out_be16(&uccup->tx_state, 0);
-		out_8(&uccup->resD4, 0);
-		out_be16(&uccup->resD5, 0);
+		qe_iowrite8(UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1,
+			    &uccup->tx_mode);
+		qe_iowrite16be(0, &uccup->tx_state);
+		qe_iowrite8(0, &uccup->resD4);
+		qe_iowrite16be(0, &uccup->resD5);
 
 		/* Set UART mode.
 		 * Enable receive and transmit.
@@ -743,22 +740,19 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
 		 * ...
 		 * 6.Receiver must use 16x over sampling
 		 */
-		clrsetbits_be32(&uccp->gumr_l,
-			UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
-			UCC_SLOW_GUMR_L_RDCR_MASK,
-			UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 |
-			UCC_SLOW_GUMR_L_RDCR_16);
+		qe_clrsetbits_be32(&uccp->gumr_l,
+				   UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK,
+				   UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 | UCC_SLOW_GUMR_L_RDCR_16);
 
-		clrsetbits_be32(&uccp->gumr_h,
-			UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
-			UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX |
-			UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
+		qe_clrsetbits_be32(&uccp->gumr_h,
+				   UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
+				   UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
 
 #ifdef LOOPBACK
-		clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
-				UCC_SLOW_GUMR_L_DIAG_LOOP);
-		clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP |
-			  UCC_SLOW_GUMR_H_CDS);
+		qe_clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
+				   UCC_SLOW_GUMR_L_DIAG_LOOP);
+		qe_clrbits_be32(&uccp->gumr_h,
+				UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_CDS);
 #endif
 
 		cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
@@ -801,7 +795,7 @@ static int qe_uart_startup(struct uart_port *port)
 	}
 
 	/* Startup rx-int */
-	setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
+	qe_setbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
 	ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX);
 
 	return 0;
@@ -837,7 +831,7 @@ static void qe_uart_shutdown(struct uart_port *port)
 
 	/* Stop uarts */
 	ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
-	clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
+	qe_clrbits_be16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
 
 	/* Shut them really down and reinit buffer descriptors */
 	ucc_slow_graceful_stop_tx(qe_port->us_private);
@@ -857,9 +851,9 @@ static void qe_uart_set_termios(struct uart_port *port,
 	struct ucc_slow __iomem *uccp = qe_port->uccp;
 	unsigned int baud;
 	unsigned long flags;
-	u16 upsmr = in_be16(&uccp->upsmr);
+	u16 upsmr = qe_ioread16be(&uccp->upsmr);
 	struct ucc_uart_pram __iomem *uccup = qe_port->uccup;
-	u16 supsmr = in_be16(&uccup->supsmr);
+	u16 supsmr = qe_ioread16be(&uccup->supsmr);
 	u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */
 
 	/* Character length programmed into the mode register is the
@@ -957,10 +951,10 @@ static void qe_uart_set_termios(struct uart_port *port,
 	/* Update the per-port timeout. */
 	uart_update_timeout(port, termios->c_cflag, baud);
 
-	out_be16(&uccp->upsmr, upsmr);
+	qe_iowrite16be(upsmr, &uccp->upsmr);
 	if (soft_uart) {
-		out_be16(&uccup->supsmr, supsmr);
-		out_8(&uccup->rx_length, char_length);
+		qe_iowrite16be(supsmr, &uccup->supsmr);
+		qe_iowrite8(char_length, &uccup->rx_length);
 
 		/* Soft-UART requires a 1X multiplier for TX */
 		qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
-- 
2.23.0

[PATCH v6 30/49] serial: ucc_uart: factor out soft_uart initialization

[Rasmus Villemoes]

The "soft uart" mechanism is a workaround for a silicon bug which (as
far as I know) only affects some PPC-based SOCs.

The code that determines which microcode blob to request relies on
some powerpc-specific bits (e.g. the mfspr(SPRN_SVR) and hence also
the asm/reg.h header). This makes it a little awkward to allow this
driver to be built for non-PPC based SOCs with a QE, even if they are
not affected by that silicon bug and thus don't need any of the Soft
UART logic.

There's no way around guarding those bits with some ifdeffery, so to
keep that isolated, factor out the
do-we-need-soft-uart-and-if-so-handle-the-firmware to a separate
function, which we can then easily stub out for non-PPC.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 110 ++++++++++++++++++----------------
 1 file changed, 58 insertions(+), 52 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 8a378ee5d34f..f286e91714cb 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1183,70 +1183,76 @@ static void uart_firmware_cont(const struct firmware *fw, void *context)
 	release_firmware(fw);
 }
 
-static int ucc_uart_probe(struct platform_device *ofdev)
+static int soft_uart_init(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
-	const unsigned int *iprop;      /* Integer OF properties */
-	const char *sprop;      /* String OF properties */
-	struct uart_qe_port *qe_port = NULL;
-	struct resource res;
+	struct qe_firmware_info *qe_fw_info;
 	int ret;
 
-	/*
-	 * Determine if we need Soft-UART mode
-	 */
 	if (of_find_property(np, "soft-uart", NULL)) {
 		dev_dbg(&ofdev->dev, "using Soft-UART mode\n");
 		soft_uart = 1;
+	} else {
+		return 0;
 	}
 
-	/*
-	 * If we are using Soft-UART, determine if we need to upload the
-	 * firmware, too.
-	 */
-	if (soft_uart) {
-		struct qe_firmware_info *qe_fw_info;
-
-		qe_fw_info = qe_get_firmware_info();
-
-		/* Check if the firmware has been uploaded. */
-		if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
-			firmware_loaded = 1;
-		} else {
-			char filename[32];
-			unsigned int soc;
-			unsigned int rev_h;
-			unsigned int rev_l;
-
-			soc = soc_info(&rev_h, &rev_l);
-			if (!soc) {
-				dev_err(&ofdev->dev, "unknown CPU model\n");
-				return -ENXIO;
-			}
-			sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
-				soc, rev_h, rev_l);
-
-			dev_info(&ofdev->dev, "waiting for firmware %s\n",
-				filename);
+	qe_fw_info = qe_get_firmware_info();
 
-			/*
-			 * We call request_firmware_nowait instead of
-			 * request_firmware so that the driver can load and
-			 * initialize the ports without holding up the rest of
-			 * the kernel.  If hotplug support is enabled in the
-			 * kernel, then we use it.
-			 */
-			ret = request_firmware_nowait(THIS_MODULE,
-				FW_ACTION_HOTPLUG, filename, &ofdev->dev,
-				GFP_KERNEL, &ofdev->dev, uart_firmware_cont);
-			if (ret) {
-				dev_err(&ofdev->dev,
-					"could not load firmware %s\n",
-					filename);
-				return ret;
-			}
+	/* Check if the firmware has been uploaded. */
+	if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
+		firmware_loaded = 1;
+	} else {
+		char filename[32];
+		unsigned int soc;
+		unsigned int rev_h;
+		unsigned int rev_l;
+
+		soc = soc_info(&rev_h, &rev_l);
+		if (!soc) {
+			dev_err(&ofdev->dev, "unknown CPU model\n");
+			return -ENXIO;
+		}
+		sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
+			soc, rev_h, rev_l);
+
+		dev_info(&ofdev->dev, "waiting for firmware %s\n",
+			 filename);
+
+		/*
+		 * We call request_firmware_nowait instead of
+		 * request_firmware so that the driver can load and
+		 * initialize the ports without holding up the rest of
+		 * the kernel.  If hotplug support is enabled in the
+		 * kernel, then we use it.
+		 */
+		ret = request_firmware_nowait(THIS_MODULE,
+					      FW_ACTION_HOTPLUG, filename, &ofdev->dev,
+					      GFP_KERNEL, &ofdev->dev, uart_firmware_cont);
+		if (ret) {
+			dev_err(&ofdev->dev,
+				"could not load firmware %s\n",
+				filename);
+			return ret;
 		}
 	}
+	return 0;
+}
+
+static int ucc_uart_probe(struct platform_device *ofdev)
+{
+	struct device_node *np = ofdev->dev.of_node;
+	const unsigned int *iprop;      /* Integer OF properties */
+	const char *sprop;      /* String OF properties */
+	struct uart_qe_port *qe_port = NULL;
+	struct resource res;
+	int ret;
+
+	/*
+	 * Determine if we need Soft-UART mode
+	 */
+	ret = soft_uart_init(ofdev);
+	if (ret)
+		return ret;
 
 	qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL);
 	if (!qe_port) {
-- 
2.23.0

[PATCH v6 31/49] serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32

[Rasmus Villemoes]

The Soft UART hack is only needed for some PPC-based SOCs. To allow
building this driver for non-PPC, guard soft_uart_init() and its
helpers by CONFIG_PPC32, and use a no-op soft_uart_init() otherwise.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index f286e91714cb..313697842e24 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -33,7 +33,10 @@
 
 #include <linux/firmware.h>
 #include <soc/fsl/cpm.h>
-#include <asm/reg.h>
+
+#ifdef CONFIG_PPC32
+#include <asm/reg.h> /* mfspr, SPRN_SVR */
+#endif
 
 /*
  * The GUMR flag for Soft UART.  This would normally be defined in qe.h,
@@ -1096,6 +1099,8 @@ static const struct uart_ops qe_uart_pops = {
 	.verify_port    = qe_uart_verify_port,
 };
 
+
+#ifdef CONFIG_PPC32
 /*
  * Obtain the SOC model number and revision level
  *
@@ -1238,6 +1243,16 @@ static int soft_uart_init(struct platform_device *ofdev)
 	return 0;
 }
 
+#else /* !CONFIG_PPC32 */
+
+static int soft_uart_init(struct platform_device *ofdev)
+{
+	return 0;
+}
+
+#endif
+
+
 static int ucc_uart_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
-- 
2.23.0

[PATCH v6 32/49] serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()

[Rasmus Villemoes]

For this to work correctly on little-endian hosts, don't access the
device-tree properties directly in native endianness, but use the
of_property_read_u32() helper.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 36 +++++++++++++++--------------------
 1 file changed, 15 insertions(+), 21 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 313697842e24..c055abf4c919 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1256,10 +1256,10 @@ static int soft_uart_init(struct platform_device *ofdev)
 static int ucc_uart_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
-	const unsigned int *iprop;      /* Integer OF properties */
 	const char *sprop;      /* String OF properties */
 	struct uart_qe_port *qe_port = NULL;
 	struct resource res;
+	u32 val;
 	int ret;
 
 	/*
@@ -1290,23 +1290,20 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 
 	/* Get the UCC number (device ID) */
 	/* UCCs are numbered 1-7 */
-	iprop = of_get_property(np, "cell-index", NULL);
-	if (!iprop) {
-		iprop = of_get_property(np, "device-id", NULL);
-		if (!iprop) {
-			dev_err(&ofdev->dev, "UCC is unspecified in "
-				"device tree\n");
+	if (of_property_read_u32(np, "cell-index", &val)) {
+		if (of_property_read_u32(np, "device-id", &val)) {
+			dev_err(&ofdev->dev, "UCC is unspecified in device tree\n");
 			ret = -EINVAL;
 			goto out_free;
 		}
 	}
 
-	if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
-		dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop);
+	if (val < 1 || val > UCC_MAX_NUM) {
+		dev_err(&ofdev->dev, "no support for UCC%u\n", val);
 		ret = -ENODEV;
 		goto out_free;
 	}
-	qe_port->ucc_num = *iprop - 1;
+	qe_port->ucc_num = val - 1;
 
 	/*
 	 * In the future, we should not require the BRG to be specified in the
@@ -1350,13 +1347,12 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 	}
 
 	/* Get the port number, numbered 0-3 */
-	iprop = of_get_property(np, "port-number", NULL);
-	if (!iprop) {
+	if (of_property_read_u32(np, "port-number", &val)) {
 		dev_err(&ofdev->dev, "missing port-number in device tree\n");
 		ret = -EINVAL;
 		goto out_free;
 	}
-	qe_port->port.line = *iprop;
+	qe_port->port.line = val;
 	if (qe_port->port.line >= UCC_MAX_UART) {
 		dev_err(&ofdev->dev, "port-number must be 0-%u\n",
 			UCC_MAX_UART - 1);
@@ -1386,31 +1382,29 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 		}
 	}
 
-	iprop = of_get_property(np, "brg-frequency", NULL);
-	if (!iprop) {
+	if (of_property_read_u32(np, "brg-frequency", &val)) {
 		dev_err(&ofdev->dev,
 		       "missing brg-frequency in device tree\n");
 		ret = -EINVAL;
 		goto out_np;
 	}
 
-	if (*iprop)
-		qe_port->port.uartclk = *iprop;
+	if (val)
+		qe_port->port.uartclk = val;
 	else {
 		/*
 		 * Older versions of U-Boot do not initialize the brg-frequency
 		 * property, so in this case we assume the BRG frequency is
 		 * half the QE bus frequency.
 		 */
-		iprop = of_get_property(np, "bus-frequency", NULL);
-		if (!iprop) {
+		if (of_property_read_u32(np, "bus-frequency", &val)) {
 			dev_err(&ofdev->dev,
 				"missing QE bus-frequency in device tree\n");
 			ret = -EINVAL;
 			goto out_np;
 		}
-		if (*iprop)
-			qe_port->port.uartclk = *iprop / 2;
+		if (val)
+			qe_port->port.uartclk = val / 2;
 		else {
 			dev_err(&ofdev->dev,
 				"invalid QE bus-frequency in device tree\n");
-- 
2.23.0

[PATCH v6 33/49] serial: ucc_uart: limit brg-frequency workaround to PPC32

[Rasmus Villemoes]

According to Timur Tabi

    This bug in older U-Boots is definitely PowerPC-specific

So before allowing this driver to be built for platforms other than
PPC32, make sure that we don't accept malformed device trees on those
other platforms.

Suggested-by: Timur Tabi <timur@kernel.org>
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index c055abf4c919..9436b93d5cfa 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1392,6 +1392,13 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 	if (val)
 		qe_port->port.uartclk = val;
 	else {
+		if (!IS_ENABLED(CONFIG_PPC32)) {
+			dev_err(&ofdev->dev,
+				"invalid brg-frequency in device tree\n");
+			ret = -EINVAL;
+			goto out_np;
+		}
+
 		/*
 		 * Older versions of U-Boot do not initialize the brg-frequency
 		 * property, so in this case we assume the BRG frequency is
-- 
2.23.0

[PATCH v6 34/49] serial: ucc_uart: access __be32 field using be32_to_cpu

[Rasmus Villemoes]

The buf member of struct qe_bd is a __be32, so to make this work on
little-endian hosts, use be32_to_cpu when reading it.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 9436b93d5cfa..afc2a5d69202 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -343,7 +343,7 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 		/* Pick next descriptor and fill from buffer */
 		bdp = qe_port->tx_cur;
 
-		p = qe2cpu_addr(bdp->buf, qe_port);
+		p = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port);
 
 		*p++ = port->x_char;
 		qe_iowrite16be(1, &bdp->length);
@@ -371,7 +371,7 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 	while (!(qe_ioread16be(&bdp->status) & BD_SC_READY) &&
 	       (xmit->tail != xmit->head)) {
 		count = 0;
-		p = qe2cpu_addr(bdp->buf, qe_port);
+		p = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port);
 		while (count < qe_port->tx_fifosize) {
 			*p++ = xmit->buf[xmit->tail];
 			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
@@ -491,7 +491,7 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port)
 		}
 
 		/* get pointer */
-		cp = qe2cpu_addr(bdp->buf, qe_port);
+		cp = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port);
 
 		/* loop through the buffer */
 		while (i-- > 0) {
-- 
2.23.0

[PATCH v6 35/49] soc: fsl: qe: change return type of cpm_muram_alloc() to s32

[Rasmus Villemoes]

There are a number of problems with cpm_muram_alloc() and its
callers. Most callers assign the return value to some variable and
then use IS_ERR_VALUE to check for allocation failure. However, when
that variable is not sizeof(long), this leads to warnings - and it is
indeed broken to do e.g.

  u32 foo = cpm_muram_alloc();
  if (IS_ERR_VALUE(foo))

on a 64-bit platform, since the condition

  foo >= (unsigned long)-ENOMEM

is tautologically false. There are also callers that ignore the
possibility of error, and then there are those that check for error by
comparing the return value to 0...

One could fix that by changing all callers to store the return value
temporarily in an "unsigned long" and test that. However, use of
IS_ERR_VALUE() is error-prone and should be restricted to things which
are inherently long-sized (stuff in pt_regs etc.). Instead, let's aim
for changing to the standard kernel style

  int foo = cpm_muram_alloc();
  if (foo < 0)
    deal_with_it()
  some->where = foo;

Changing the return type from unsigned long to s32 (aka signed int)
doesn't change the value that gets stored into any of the callers'
variables except if the caller was storing the result in a u64 _and_
the allocation failed, so in itself this patch should be a no-op.

Another problem with cpm_muram_alloc() is that it can certainly
validly return 0 - and except if some cpm_muram_alloc_fixed() call
interferes, the very first cpm_muram_alloc() call will return just
that. But that shows that both ucc_slow_free() and ucc_fast_free() are
buggy, since they assume that a value of 0 means "that field was never
allocated". We'll later change cpm_muram_free() to accept (and ignore)
a negative offset, so callers can use a sentinel of -1 instead of 0
and just unconditionally call cpm_muram_free().

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_common.c | 29 ++++++++++++++++-------------
 include/soc/fsl/qe/qe.h        | 16 ++++++++--------
 2 files changed, 24 insertions(+), 21 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_common.c b/drivers/soc/fsl/qe/qe_common.c
index 83e85e61669f..84c90105e588 100644
--- a/drivers/soc/fsl/qe/qe_common.c
+++ b/drivers/soc/fsl/qe/qe_common.c
@@ -32,7 +32,7 @@ static phys_addr_t muram_pbase;
 
 struct muram_block {
 	struct list_head head;
-	unsigned long start;
+	s32 start;
 	int size;
 };
 
@@ -110,13 +110,14 @@ int cpm_muram_init(void)
  * @algo: algorithm for alloc.
  * @data: data for genalloc's algorithm.
  *
- * This function returns an offset into the muram area.
+ * This function returns a non-negative offset into the muram area, or
+ * a negative errno on failure.
  */
-static unsigned long cpm_muram_alloc_common(unsigned long size,
-		genpool_algo_t algo, void *data)
+static s32 cpm_muram_alloc_common(unsigned long size,
+				  genpool_algo_t algo, void *data)
 {
 	struct muram_block *entry;
-	unsigned long start;
+	s32 start;
 
 	if (!muram_pool && cpm_muram_init())
 		goto out2;
@@ -137,7 +138,7 @@ static unsigned long cpm_muram_alloc_common(unsigned long size,
 out1:
 	gen_pool_free(muram_pool, start, size);
 out2:
-	return (unsigned long)-ENOMEM;
+	return -ENOMEM;
 }
 
 /*
@@ -145,13 +146,14 @@ static unsigned long cpm_muram_alloc_common(unsigned long size,
  * @size: number of bytes to allocate
  * @align: requested alignment, in bytes
  *
- * This function returns an offset into the muram area.
+ * This function returns a non-negative offset into the muram area, or
+ * a negative errno on failure.
  * Use cpm_dpram_addr() to get the virtual address of the area.
  * Use cpm_muram_free() to free the allocation.
  */
-unsigned long cpm_muram_alloc(unsigned long size, unsigned long align)
+s32 cpm_muram_alloc(unsigned long size, unsigned long align)
 {
-	unsigned long start;
+	s32 start;
 	unsigned long flags;
 	struct genpool_data_align muram_pool_data;
 
@@ -168,7 +170,7 @@ EXPORT_SYMBOL(cpm_muram_alloc);
  * cpm_muram_free - free a chunk of multi-user ram
  * @offset: The beginning of the chunk as returned by cpm_muram_alloc().
  */
-int cpm_muram_free(unsigned long offset)
+int cpm_muram_free(s32 offset)
 {
 	unsigned long flags;
 	int size;
@@ -194,13 +196,14 @@ EXPORT_SYMBOL(cpm_muram_free);
  * cpm_muram_alloc_fixed - reserve a specific region of multi-user ram
  * @offset: offset of allocation start address
  * @size: number of bytes to allocate
- * This function returns an offset into the muram area
+ * This function returns @offset if the area was available, a negative
+ * errno otherwise.
  * Use cpm_dpram_addr() to get the virtual address of the area.
  * Use cpm_muram_free() to free the allocation.
  */
-unsigned long cpm_muram_alloc_fixed(unsigned long offset, unsigned long size)
+s32 cpm_muram_alloc_fixed(unsigned long offset, unsigned long size)
 {
-	unsigned long start;
+	s32 start;
 	unsigned long flags;
 	struct genpool_data_fixed muram_pool_data_fixed;
 
diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
index 521fa3a177e0..f589ae3f1216 100644
--- a/include/soc/fsl/qe/qe.h
+++ b/include/soc/fsl/qe/qe.h
@@ -98,26 +98,26 @@ static inline void qe_reset(void) {}
 int cpm_muram_init(void);
 
 #if defined(CONFIG_CPM) || defined(CONFIG_QUICC_ENGINE)
-unsigned long cpm_muram_alloc(unsigned long size, unsigned long align);
-int cpm_muram_free(unsigned long offset);
-unsigned long cpm_muram_alloc_fixed(unsigned long offset, unsigned long size);
+s32 cpm_muram_alloc(unsigned long size, unsigned long align);
+int cpm_muram_free(s32 offset);
+s32 cpm_muram_alloc_fixed(unsigned long offset, unsigned long size);
 void __iomem *cpm_muram_addr(unsigned long offset);
 unsigned long cpm_muram_offset(void __iomem *addr);
 dma_addr_t cpm_muram_dma(void __iomem *addr);
 #else
-static inline unsigned long cpm_muram_alloc(unsigned long size,
-					    unsigned long align)
+static inline s32 cpm_muram_alloc(unsigned long size,
+				  unsigned long align)
 {
 	return -ENOSYS;
 }
 
-static inline int cpm_muram_free(unsigned long offset)
+static inline int cpm_muram_free(s32 offset)
 {
 	return -ENOSYS;
 }
 
-static inline unsigned long cpm_muram_alloc_fixed(unsigned long offset,
-						  unsigned long size)
+static inline s32 cpm_muram_alloc_fixed(unsigned long offset,
+					unsigned long size)
 {
 	return -ENOSYS;
 }
-- 
2.23.0

[PATCH v6 36/49] soc: fsl: qe: make cpm_muram_free() return void

[Rasmus Villemoes]

Nobody uses the return value from cpm_muram_free, and functions that
free resources usually return void. One could imagine a use for a "how
much have I allocated" a la ksize(), but knowing how much one had
access to after the fact is useless.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_common.c | 3 +--
 include/soc/fsl/qe/qe.h        | 5 ++---
 2 files changed, 3 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_common.c b/drivers/soc/fsl/qe/qe_common.c
index 84c90105e588..962835488f66 100644
--- a/drivers/soc/fsl/qe/qe_common.c
+++ b/drivers/soc/fsl/qe/qe_common.c
@@ -170,7 +170,7 @@ EXPORT_SYMBOL(cpm_muram_alloc);
  * cpm_muram_free - free a chunk of multi-user ram
  * @offset: The beginning of the chunk as returned by cpm_muram_alloc().
  */
-int cpm_muram_free(s32 offset)
+void cpm_muram_free(s32 offset)
 {
 	unsigned long flags;
 	int size;
@@ -188,7 +188,6 @@ int cpm_muram_free(s32 offset)
 	}
 	gen_pool_free(muram_pool, offset + GENPOOL_OFFSET, size);
 	spin_unlock_irqrestore(&cpm_muram_lock, flags);
-	return size;
 }
 EXPORT_SYMBOL(cpm_muram_free);
 
diff --git a/include/soc/fsl/qe/qe.h b/include/soc/fsl/qe/qe.h
index f589ae3f1216..e282ac01ec08 100644
--- a/include/soc/fsl/qe/qe.h
+++ b/include/soc/fsl/qe/qe.h
@@ -99,7 +99,7 @@ int cpm_muram_init(void);
 
 #if defined(CONFIG_CPM) || defined(CONFIG_QUICC_ENGINE)
 s32 cpm_muram_alloc(unsigned long size, unsigned long align);
-int cpm_muram_free(s32 offset);
+void cpm_muram_free(s32 offset);
 s32 cpm_muram_alloc_fixed(unsigned long offset, unsigned long size);
 void __iomem *cpm_muram_addr(unsigned long offset);
 unsigned long cpm_muram_offset(void __iomem *addr);
@@ -111,9 +111,8 @@ static inline s32 cpm_muram_alloc(unsigned long size,
 	return -ENOSYS;
 }
 
-static inline int cpm_muram_free(s32 offset)
+static inline void cpm_muram_free(s32 offset)
 {
-	return -ENOSYS;
 }
 
 static inline s32 cpm_muram_alloc_fixed(unsigned long offset,
-- 
2.23.0

[PATCH v6 37/49] soc: fsl: qe: make cpm_muram_free() ignore a negative offset

[Rasmus Villemoes]

This allows one to simplify callers since they can store a negative
value as a sentinel to indicate "this was never allocated" (or store
the -ENOMEM from an allocation failure) and then call cpm_muram_free()
unconditionally.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_common.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/soc/fsl/qe/qe_common.c b/drivers/soc/fsl/qe/qe_common.c
index 962835488f66..48c77bb92846 100644
--- a/drivers/soc/fsl/qe/qe_common.c
+++ b/drivers/soc/fsl/qe/qe_common.c
@@ -176,6 +176,9 @@ void cpm_muram_free(s32 offset)
 	int size;
 	struct muram_block *tmp;
 
+	if (offset < 0)
+		return;
+
 	size = 0;
 	spin_lock_irqsave(&cpm_muram_lock, flags);
 	list_for_each_entry(tmp, &muram_block_list, head) {
-- 
2.23.0

[PATCH v6 38/49] soc: fsl: qe: drop broken lazy call of cpm_muram_init()

[Rasmus Villemoes]

cpm_muram_alloc_common() tries to support a kind of lazy
initialization - if the muram_pool has not been created yet, it calls
cpm_muram_init(). Now, cpm_muram_alloc_common() is always called under

	spin_lock_irqsave(&cpm_muram_lock, flags);

and cpm_muram_init() does gen_pool_create() (which implies a
GFP_KERNEL allocation) and ioremap(), not to mention the fun that
ensues from cpm_muram_init() doing

	spin_lock_init(&cpm_muram_lock);

In other words, this has never worked, so nobody can have been relying
on it.

cpm_muram_init() is called from a subsys_initcall (either from
cpm_init() in arch/powerpc/sysdev/cpm_common.c or, via qe_reset(),
from qe_init() in drivers/soc/fsl/qe/qe.c).

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_common.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_common.c b/drivers/soc/fsl/qe/qe_common.c
index 48c77bb92846..dcb267567d76 100644
--- a/drivers/soc/fsl/qe/qe_common.c
+++ b/drivers/soc/fsl/qe/qe_common.c
@@ -119,9 +119,6 @@ static s32 cpm_muram_alloc_common(unsigned long size,
 	struct muram_block *entry;
 	s32 start;
 
-	if (!muram_pool && cpm_muram_init())
-		goto out2;
-
 	start = gen_pool_alloc_algo(muram_pool, size, algo, data);
 	if (!start)
 		goto out2;
-- 
2.23.0

[PATCH v6 39/49] soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path

[Rasmus Villemoes]

If the kmalloc() fails, we try to undo the gen_pool allocation we've
just done. Unfortunately, start has already been modified to subtract
the GENPOOL_OFFSET bias, so we're freeing something that very likely
doesn't exist in the gen_pool, meaning we hit the

 kernel BUG at lib/genalloc.c:399!
 Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
 ...
 [<803fd0e8>] (gen_pool_free) from [<80426bc8>] (cpm_muram_alloc_common+0xb0/0xc8)
 [<80426bc8>] (cpm_muram_alloc_common) from [<80426c28>] (cpm_muram_alloc+0x48/0x80)
 [<80426c28>] (cpm_muram_alloc) from [<80428214>] (ucc_slow_init+0x110/0x4f0)
 [<80428214>] (ucc_slow_init) from [<8044a718>] (qe_uart_request_port+0x3c/0x1d8)

(this was tested by just injecting a random failure by adding
"|| (get_random_int()&7) == 0" to the "if (!entry)" condition).

Refactor the code so we do the kmalloc() first, meaning that's the
thing that needs undoing in case gen_pool_alloc_algo() then
fails. This allows a later cleanup to move the locking from the
callers into the _common function, keeping the kmalloc() out of the
critical region and then, hopefully (if all the muram_alloc callers
allow) change it to a GFP_KERNEL allocation.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe_common.c | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe_common.c b/drivers/soc/fsl/qe/qe_common.c
index dcb267567d76..a81a1a79f1ca 100644
--- a/drivers/soc/fsl/qe/qe_common.c
+++ b/drivers/soc/fsl/qe/qe_common.c
@@ -119,23 +119,21 @@ static s32 cpm_muram_alloc_common(unsigned long size,
 	struct muram_block *entry;
 	s32 start;
 
+	entry = kmalloc(sizeof(*entry), GFP_ATOMIC);
+	if (!entry)
+		return -ENOMEM;
 	start = gen_pool_alloc_algo(muram_pool, size, algo, data);
-	if (!start)
-		goto out2;
+	if (!start) {
+		kfree(entry);
+		return -ENOMEM;
+	}
 	start = start - GENPOOL_OFFSET;
 	memset_io(cpm_muram_addr(start), 0, size);
-	entry = kmalloc(sizeof(*entry), GFP_ATOMIC);
-	if (!entry)
-		goto out1;
 	entry->start = start;
 	entry->size = size;
 	list_add(&entry->head, &muram_block_list);
 
 	return start;
-out1:
-	gen_pool_free(muram_pool, start, size);
-out2:
-	return -ENOMEM;
 }
 
 /*
-- 
2.23.0

[PATCH v6 40/49] soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c

[Rasmus Villemoes]

When trying to build this for a 64-bit platform, one gets warnings
from using IS_ERR_VALUE on something which is not sizeof(long).

Instead, change the various *_offset fields to store a signed integer,
and simply check for a negative return from qe_muram_alloc(). Since
qe_muram_free() now accepts and ignores a negative argument, we only
need to make sure these fields are initialized with -1, and we can
just unconditionally call qe_muram_free() in ucc_slow_free().

Note that the error case for us_pram_offset failed to set that field
to 0 (which, as noted earlier, is anyway a bogus sentinel value).

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/ucc_slow.c | 22 +++++++++-------------
 include/soc/fsl/qe/ucc_slow.h |  6 +++---
 2 files changed, 12 insertions(+), 16 deletions(-)

diff --git a/drivers/soc/fsl/qe/ucc_slow.c b/drivers/soc/fsl/qe/ucc_slow.c
index 9b55fd0f50c6..274d34449846 100644
--- a/drivers/soc/fsl/qe/ucc_slow.c
+++ b/drivers/soc/fsl/qe/ucc_slow.c
@@ -154,6 +154,9 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 			__func__);
 		return -ENOMEM;
 	}
+	uccs->rx_base_offset = -1;
+	uccs->tx_base_offset = -1;
+	uccs->us_pram_offset = -1;
 
 	/* Fill slow UCC structure */
 	uccs->us_info = us_info;
@@ -179,7 +182,7 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 	/* Get PRAM base */
 	uccs->us_pram_offset =
 		qe_muram_alloc(UCC_SLOW_PRAM_SIZE, ALIGNMENT_OF_UCC_SLOW_PRAM);
-	if (IS_ERR_VALUE(uccs->us_pram_offset)) {
+	if (uccs->us_pram_offset < 0) {
 		printk(KERN_ERR "%s: cannot allocate MURAM for PRAM", __func__);
 		ucc_slow_free(uccs);
 		return -ENOMEM;
@@ -206,10 +209,9 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 	uccs->rx_base_offset =
 		qe_muram_alloc(us_info->rx_bd_ring_len * sizeof(struct qe_bd),
 				QE_ALIGNMENT_OF_BD);
-	if (IS_ERR_VALUE(uccs->rx_base_offset)) {
+	if (uccs->rx_base_offset < 0) {
 		printk(KERN_ERR "%s: cannot allocate %u RX BDs\n", __func__,
 			us_info->rx_bd_ring_len);
-		uccs->rx_base_offset = 0;
 		ucc_slow_free(uccs);
 		return -ENOMEM;
 	}
@@ -217,9 +219,8 @@ int ucc_slow_init(struct ucc_slow_info * us_info, struct ucc_slow_private ** ucc
 	uccs->tx_base_offset =
 		qe_muram_alloc(us_info->tx_bd_ring_len * sizeof(struct qe_bd),
 			QE_ALIGNMENT_OF_BD);
-	if (IS_ERR_VALUE(uccs->tx_base_offset)) {
+	if (uccs->tx_base_offset < 0) {
 		printk(KERN_ERR "%s: cannot allocate TX BDs", __func__);
-		uccs->tx_base_offset = 0;
 		ucc_slow_free(uccs);
 		return -ENOMEM;
 	}
@@ -352,14 +353,9 @@ void ucc_slow_free(struct ucc_slow_private * uccs)
 	if (!uccs)
 		return;
 
-	if (uccs->rx_base_offset)
-		qe_muram_free(uccs->rx_base_offset);
-
-	if (uccs->tx_base_offset)
-		qe_muram_free(uccs->tx_base_offset);
-
-	if (uccs->us_pram)
-		qe_muram_free(uccs->us_pram_offset);
+	qe_muram_free(uccs->rx_base_offset);
+	qe_muram_free(uccs->tx_base_offset);
+	qe_muram_free(uccs->us_pram_offset);
 
 	if (uccs->us_regs)
 		iounmap(uccs->us_regs);
diff --git a/include/soc/fsl/qe/ucc_slow.h b/include/soc/fsl/qe/ucc_slow.h
index 8696fdea2ae9..d187a6be83bc 100644
--- a/include/soc/fsl/qe/ucc_slow.h
+++ b/include/soc/fsl/qe/ucc_slow.h
@@ -185,7 +185,7 @@ struct ucc_slow_private {
 	struct ucc_slow_info *us_info;
 	struct ucc_slow __iomem *us_regs; /* Ptr to memory map of UCC regs */
 	struct ucc_slow_pram *us_pram;	/* a pointer to the parameter RAM */
-	u32 us_pram_offset;
+	s32 us_pram_offset;
 	int enabled_tx;		/* Whether channel is enabled for Tx (ENT) */
 	int enabled_rx;		/* Whether channel is enabled for Rx (ENR) */
 	int stopped_tx;		/* Whether channel has been stopped for Tx
@@ -194,8 +194,8 @@ struct ucc_slow_private {
 	struct list_head confQ;	/* frames passed to chip waiting for tx */
 	u32 first_tx_bd_mask;	/* mask is used in Tx routine to save status
 				   and length for first BD in a frame */
-	u32 tx_base_offset;	/* first BD in Tx BD table offset (In MURAM) */
-	u32 rx_base_offset;	/* first BD in Rx BD table offset (In MURAM) */
+	s32 tx_base_offset;	/* first BD in Tx BD table offset (In MURAM) */
+	s32 rx_base_offset;	/* first BD in Rx BD table offset (In MURAM) */
 	struct qe_bd *confBd;	/* next BD for confirm after Tx */
 	struct qe_bd *tx_bd;	/* next BD for new Tx request */
 	struct qe_bd *rx_bd;	/* next BD to collect after Rx */
-- 
2.23.0

[PATCH v6 41/49] soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()

[Rasmus Villemoes]

Now that qe_muram_alloc() returns s32, adapt qe_sdma_init() and avoid
another few IS_ERR_VALUE() uses.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index ec511840db3c..5bf279c679ef 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -365,16 +365,16 @@ EXPORT_SYMBOL(qe_put_snum);
 static int qe_sdma_init(void)
 {
 	struct sdma __iomem *sdma = &qe_immr->sdma;
-	static unsigned long sdma_buf_offset = (unsigned long)-ENOMEM;
+	static s32 sdma_buf_offset = -ENOMEM;
 
 	if (!sdma)
 		return -ENODEV;
 
 	/* allocate 2 internal temporary buffers (512 bytes size each) for
 	 * the SDMA */
-	if (IS_ERR_VALUE(sdma_buf_offset)) {
+	if (sdma_buf_offset < 0) {
 		sdma_buf_offset = qe_muram_alloc(512 * 2, 4096);
-		if (IS_ERR_VALUE(sdma_buf_offset))
+		if (sdma_buf_offset < 0)
 			return -ENOMEM;
 	}
 
-- 
2.23.0

[PATCH v6 42/49] soc: fsl: qe: drop pointless check in qe_sdma_init()

[Rasmus Villemoes]

The sdma member of struct qe_immap is not at offset zero, so even if
qe_immr wasn't initialized yet (i.e. NULL), &qe_immr->sdma would not
be NULL.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/qe.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index 5bf279c679ef..96c2057d8d8e 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -367,9 +367,6 @@ static int qe_sdma_init(void)
 	struct sdma __iomem *sdma = &qe_immr->sdma;
 	static s32 sdma_buf_offset = -ENOMEM;
 
-	if (!sdma)
-		return -ENODEV;
-
 	/* allocate 2 internal temporary buffers (512 bytes size each) for
 	 * the SDMA */
 	if (sdma_buf_offset < 0) {
-- 
2.23.0

[PATCH v6 43/49] soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c

[Rasmus Villemoes]

When building this on a 64-bit platform gcc rightly warns that the
error checking is broken (-ENOMEM stored in an u32 does not compare
greater than (unsigned long)-MAX_ERRNO). Instead, change the
ucc_fast_[tr]x_virtual_fifo_base_offset members to s32 and use an
ordinary check-for-negative. Also, this avoids treating 0 as "this
cannot have been returned from qe_muram_alloc() so don't free it".

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/ucc_fast.c | 15 ++++++---------
 include/soc/fsl/qe/ucc_fast.h |  4 ++--
 2 files changed, 8 insertions(+), 11 deletions(-)

diff --git a/drivers/soc/fsl/qe/ucc_fast.c b/drivers/soc/fsl/qe/ucc_fast.c
index ca0452497a20..ad6193ea4597 100644
--- a/drivers/soc/fsl/qe/ucc_fast.c
+++ b/drivers/soc/fsl/qe/ucc_fast.c
@@ -197,6 +197,8 @@ int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** ucc
 			__func__);
 		return -ENOMEM;
 	}
+	uccf->ucc_fast_tx_virtual_fifo_base_offset = -1;
+	uccf->ucc_fast_rx_virtual_fifo_base_offset = -1;
 
 	/* Fill fast UCC structure */
 	uccf->uf_info = uf_info;
@@ -265,10 +267,9 @@ int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** ucc
 	/* Allocate memory for Tx Virtual Fifo */
 	uccf->ucc_fast_tx_virtual_fifo_base_offset =
 	    qe_muram_alloc(uf_info->utfs, UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT);
-	if (IS_ERR_VALUE(uccf->ucc_fast_tx_virtual_fifo_base_offset)) {
+	if (uccf->ucc_fast_tx_virtual_fifo_base_offset < 0) {
 		printk(KERN_ERR "%s: cannot allocate MURAM for TX FIFO\n",
 			__func__);
-		uccf->ucc_fast_tx_virtual_fifo_base_offset = 0;
 		ucc_fast_free(uccf);
 		return -ENOMEM;
 	}
@@ -278,10 +279,9 @@ int ucc_fast_init(struct ucc_fast_info * uf_info, struct ucc_fast_private ** ucc
 		qe_muram_alloc(uf_info->urfs +
 			   UCC_FAST_RECEIVE_VIRTUAL_FIFO_SIZE_FUDGE_FACTOR,
 			   UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT);
-	if (IS_ERR_VALUE(uccf->ucc_fast_rx_virtual_fifo_base_offset)) {
+	if (uccf->ucc_fast_rx_virtual_fifo_base_offset < 0) {
 		printk(KERN_ERR "%s: cannot allocate MURAM for RX FIFO\n",
 			__func__);
-		uccf->ucc_fast_rx_virtual_fifo_base_offset = 0;
 		ucc_fast_free(uccf);
 		return -ENOMEM;
 	}
@@ -384,11 +384,8 @@ void ucc_fast_free(struct ucc_fast_private * uccf)
 	if (!uccf)
 		return;
 
-	if (uccf->ucc_fast_tx_virtual_fifo_base_offset)
-		qe_muram_free(uccf->ucc_fast_tx_virtual_fifo_base_offset);
-
-	if (uccf->ucc_fast_rx_virtual_fifo_base_offset)
-		qe_muram_free(uccf->ucc_fast_rx_virtual_fifo_base_offset);
+	qe_muram_free(uccf->ucc_fast_tx_virtual_fifo_base_offset);
+	qe_muram_free(uccf->ucc_fast_rx_virtual_fifo_base_offset);
 
 	if (uccf->uf_regs)
 		iounmap(uccf->uf_regs);
diff --git a/include/soc/fsl/qe/ucc_fast.h b/include/soc/fsl/qe/ucc_fast.h
index e9cc46042a83..ba0e838f962a 100644
--- a/include/soc/fsl/qe/ucc_fast.h
+++ b/include/soc/fsl/qe/ucc_fast.h
@@ -188,9 +188,9 @@ struct ucc_fast_private {
 	int stopped_tx;		/* Whether channel has been stopped for Tx
 				   (STOP_TX, etc.) */
 	int stopped_rx;		/* Whether channel has been stopped for Rx */
-	u32 ucc_fast_tx_virtual_fifo_base_offset;/* pointer to base of Tx
+	s32 ucc_fast_tx_virtual_fifo_base_offset;/* pointer to base of Tx
 						    virtual fifo */
-	u32 ucc_fast_rx_virtual_fifo_base_offset;/* pointer to base of Rx
+	s32 ucc_fast_rx_virtual_fifo_base_offset;/* pointer to base of Rx
 						    virtual fifo */
 #ifdef STATISTICS
 	u32 tx_frames;		/* Transmitted frames counter. */
-- 
2.23.0

[PATCH v6 44/49] net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()

[Rasmus Villemoes]

When building this on a 64-bit platform gcc rightly warns that the
error checking is broken (-ENOMEM stored in an u32 does not compare
greater than (unsigned long)-MAX_ERRNO). Instead, now that
qe_muram_alloc() returns s32, use that type to store the return value
and use standard kernel style "ret < 0".

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/net/wan/fsl_ucc_hdlc.c | 10 +++++-----
 drivers/net/wan/fsl_ucc_hdlc.h |  2 +-
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wan/fsl_ucc_hdlc.c b/drivers/net/wan/fsl_ucc_hdlc.c
index ce6af7d5380f..405b24a5a60d 100644
--- a/drivers/net/wan/fsl_ucc_hdlc.c
+++ b/drivers/net/wan/fsl_ucc_hdlc.c
@@ -84,8 +84,8 @@ static int uhdlc_init(struct ucc_hdlc_private *priv)
 	int ret, i;
 	void *bd_buffer;
 	dma_addr_t bd_dma_addr;
-	u32 riptr;
-	u32 tiptr;
+	s32 riptr;
+	s32 tiptr;
 	u32 gumr;
 
 	ut_info = priv->ut_info;
@@ -195,7 +195,7 @@ static int uhdlc_init(struct ucc_hdlc_private *priv)
 	priv->ucc_pram_offset = qe_muram_alloc(sizeof(struct ucc_hdlc_param),
 				ALIGNMENT_OF_UCC_HDLC_PRAM);
 
-	if (IS_ERR_VALUE(priv->ucc_pram_offset)) {
+	if (priv->ucc_pram_offset < 0) {
 		dev_err(priv->dev, "Can not allocate MURAM for hdlc parameter.\n");
 		ret = -ENOMEM;
 		goto free_tx_bd;
@@ -233,14 +233,14 @@ static int uhdlc_init(struct ucc_hdlc_private *priv)
 
 	/* Alloc riptr, tiptr */
 	riptr = qe_muram_alloc(32, 32);
-	if (IS_ERR_VALUE(riptr)) {
+	if (riptr < 0) {
 		dev_err(priv->dev, "Cannot allocate MURAM mem for Receive internal temp data pointer\n");
 		ret = -ENOMEM;
 		goto free_tx_skbuff;
 	}
 
 	tiptr = qe_muram_alloc(32, 32);
-	if (IS_ERR_VALUE(tiptr)) {
+	if (tiptr < 0) {
 		dev_err(priv->dev, "Cannot allocate MURAM mem for Transmit internal temp data pointer\n");
 		ret = -ENOMEM;
 		goto free_riptr;
diff --git a/drivers/net/wan/fsl_ucc_hdlc.h b/drivers/net/wan/fsl_ucc_hdlc.h
index 8b3507ae1781..71d5ad0a7b98 100644
--- a/drivers/net/wan/fsl_ucc_hdlc.h
+++ b/drivers/net/wan/fsl_ucc_hdlc.h
@@ -98,7 +98,7 @@ struct ucc_hdlc_private {
 
 	unsigned short tx_ring_size;
 	unsigned short rx_ring_size;
-	u32 ucc_pram_offset;
+	s32 ucc_pram_offset;
 
 	unsigned short encoding;
 	unsigned short parity;
-- 
2.23.0

RE: [PATCH v6 44/49] net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()

[Leo Li]

> -----Original Message-----
> From: Rasmus Villemoes <linux@rasmusvillemoes.dk>
> Sent: Thursday, November 28, 2019 8:56 AM
> To: Qiang Zhao <qiang.zhao@nxp.com>; Leo Li <leoyang.li@nxp.com>;
> Christophe Leroy <christophe.leroy@c-s.fr>
> Cc: linuxppc-dev@lists.ozlabs.org; linux-arm-kernel@lists.infradead.org;
> linux-kernel@vger.kernel.org; Scott Wood <oss@buserror.net>; Timur Tabi
> <timur@kernel.org>; Rasmus Villemoes <linux@rasmusvillemoes.dk>;
> netdev@vger.kernel.org
> Subject: [PATCH v6 44/49] net/wan/fsl_ucc_hdlc: avoid use of
> IS_ERR_VALUE()

Hi David,

Would you help to review patch 44-47 in the series?  If it is fine with you, I can take these 4 patches with the whole series though soc tree to enable the QE drivers on ARM and PPC64 with your ACK.

Thanks,
Leo

> 
> When building this on a 64-bit platform gcc rightly warns that the error
> checking is broken (-ENOMEM stored in an u32 does not compare greater
> than (unsigned long)-MAX_ERRNO). Instead, now that
> qe_muram_alloc() returns s32, use that type to store the return value and
> use standard kernel style "ret < 0".
> 
> Reviewed-by: Timur Tabi <timur@kernel.org>
> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>

Re: [PATCH v6 44/49] net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()

[David Miller]

From: Leo Li <leoyang.li@nxp.com>
Date: Mon, 2 Dec 2019 22:51:57 +0000

> 
> 
>> -----Original Message-----
>> From: Rasmus Villemoes <linux@rasmusvillemoes.dk>
>> Sent: Thursday, November 28, 2019 8:56 AM
>> To: Qiang Zhao <qiang.zhao@nxp.com>; Leo Li <leoyang.li@nxp.com>;
>> Christophe Leroy <christophe.leroy@c-s.fr>
>> Cc: linuxppc-dev@lists.ozlabs.org; linux-arm-kernel@lists.infradead.org;
>> linux-kernel@vger.kernel.org; Scott Wood <oss@buserror.net>; Timur Tabi
>> <timur@kernel.org>; Rasmus Villemoes <linux@rasmusvillemoes.dk>;
>> netdev@vger.kernel.org
>> Subject: [PATCH v6 44/49] net/wan/fsl_ucc_hdlc: avoid use of
>> IS_ERR_VALUE()
> 
> Hi David,
> 
> Would you help to review patch 44-47 in the series?  If it is fine with you, I can take these 4 patches with the whole series though soc tree to enable the QE drivers on ARM and PPC64 with your ACK.

Please take it via your tree, that's fine.

[PATCH v6 45/49] net/wan/fsl_ucc_hdlc: fix reading of __be16 registers

[Rasmus Villemoes]

When releasing the allocated muram resource, we rely on reading back
the offsets from the riptr/tiptr registers. But those registers are
__be16 (and we indeed write them using iowrite16be), so we can't just
read them back with a normal C dereference.

This is not currently a real problem, since for now the driver is
PPC32-only. But it will soon be allowed to be used on arm and arm64 as
well.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/net/wan/fsl_ucc_hdlc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wan/fsl_ucc_hdlc.c b/drivers/net/wan/fsl_ucc_hdlc.c
index 405b24a5a60d..8d13586bb774 100644
--- a/drivers/net/wan/fsl_ucc_hdlc.c
+++ b/drivers/net/wan/fsl_ucc_hdlc.c
@@ -732,8 +732,8 @@ static int uhdlc_open(struct net_device *dev)
 
 static void uhdlc_memclean(struct ucc_hdlc_private *priv)
 {
-	qe_muram_free(priv->ucc_pram->riptr);
-	qe_muram_free(priv->ucc_pram->tiptr);
+	qe_muram_free(ioread16be(&priv->ucc_pram->riptr));
+	qe_muram_free(ioread16be(&priv->ucc_pram->tiptr));
 
 	if (priv->rx_bd_base) {
 		dma_free_coherent(priv->dev,
-- 
2.23.0

[PATCH v6 46/49] net/wan/fsl_ucc_hdlc: reject muram offsets above 64K

[Rasmus Villemoes]

Qiang Zhao points out that these offsets get written to 16-bit
registers, and there are some QE platforms with more than 64K
muram. So it is possible that qe_muram_alloc() gives us an allocation
that can't actually be used by the hardware, so detect and reject
that.

Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/net/wan/fsl_ucc_hdlc.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/net/wan/fsl_ucc_hdlc.c b/drivers/net/wan/fsl_ucc_hdlc.c
index 8d13586bb774..f029eaa7cfc0 100644
--- a/drivers/net/wan/fsl_ucc_hdlc.c
+++ b/drivers/net/wan/fsl_ucc_hdlc.c
@@ -245,6 +245,11 @@ static int uhdlc_init(struct ucc_hdlc_private *priv)
 		ret = -ENOMEM;
 		goto free_riptr;
 	}
+	if (riptr != (u16)riptr || tiptr != (u16)tiptr) {
+		dev_err(priv->dev, "MURAM allocation out of addressable range\n");
+		ret = -ENOMEM;
+		goto free_tiptr;
+	}
 
 	/* Set RIPTR, TIPTR */
 	iowrite16be(riptr, &priv->ucc_pram->riptr);
-- 
2.23.0

[PATCH v6 47/49] net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32

[Rasmus Villemoes]

Currently, QUICC_ENGINE depends on PPC32, so this in itself does not
change anything. In order to allow removing the PPC32 dependency from
QUICC_ENGINE and avoid allmodconfig build failures, add this explicit
dependency.

Also, the QE Ethernet has never been integrated on any non-PowerPC SoC
and most likely will not be in the future.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/net/ethernet/freescale/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/freescale/Kconfig b/drivers/net/ethernet/freescale/Kconfig
index 6a7e8993119f..2bd7ace0a953 100644
--- a/drivers/net/ethernet/freescale/Kconfig
+++ b/drivers/net/ethernet/freescale/Kconfig
@@ -74,7 +74,7 @@ config FSL_XGMAC_MDIO
 
 config UCC_GETH
 	tristate "Freescale QE Gigabit Ethernet"
-	depends on QUICC_ENGINE
+	depends on QUICC_ENGINE && PPC32
 	select FSL_PQ_MDIO
 	select PHYLIB
 	---help---
-- 
2.23.0

[PATCH v6 48/49] soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c

[Rasmus Villemoes]

When allowing this driver to be built for ARM, the build fails (for
CONFIG_SMP=y) since ARM's asm/irq.h header is not self-contained:

  In file included from drivers/soc/fsl/qe/ucc.c:18:0:
>> arch/arm/include/asm/irq.h:34:50: error: unknown type name 'cpumask_t'
    extern void arch_trigger_cpumask_backtrace(const cpumask_t *mask,

But nothing in this file actually uses anything from asm/irq.h -
removing this #include generates identical object code, both on PPC32
and on ARM (the latter with a patch added to asm/irq.h to make the
build work in the first place).

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/ucc.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/soc/fsl/qe/ucc.c b/drivers/soc/fsl/qe/ucc.c
index da3d7e2dd837..90157acc5ba6 100644
--- a/drivers/soc/fsl/qe/ucc.c
+++ b/drivers/soc/fsl/qe/ucc.c
@@ -15,7 +15,6 @@
 #include <linux/spinlock.h>
 #include <linux/export.h>
 
-#include <asm/irq.h>
 #include <asm/io.h>
 #include <soc/fsl/qe/immap_qe.h>
 #include <soc/fsl/qe/qe.h>
-- 
2.23.0

[PATCH v6 49/49] soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE

[Rasmus Villemoes]

There are also PPC64, ARM and ARM64 based SOCs with a QUICC Engine,
and the core QE code as well as net/wan/fsl_ucc_hdlc and
tty/serial/ucc_uart has now been modified to not rely on ppcisms.

So extend the architectures that can select QUICC_ENGINE, and add the
rather modest requirements of OF && HAS_IOMEM.

The core code as well as the ucc_uart driver has been tested on an
LS1021A (arm), and it has also been tested that the QE code still
works on an mpc8309 (ppc). Qiang Zhao has tested that the QE-HDLC code
that gets enabled with this works on ARM64.

Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/soc/fsl/qe/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/soc/fsl/qe/Kconfig b/drivers/soc/fsl/qe/Kconfig
index cfa4b2939992..357c5800b112 100644
--- a/drivers/soc/fsl/qe/Kconfig
+++ b/drivers/soc/fsl/qe/Kconfig
@@ -5,7 +5,8 @@
 
 config QUICC_ENGINE
 	bool "QUICC Engine (QE) framework support"
-	depends on FSL_SOC && PPC32
+	depends on OF && HAS_IOMEM
+	depends on PPC || ARM || ARM64 || COMPILE_TEST
 	select GENERIC_ALLOCATOR
 	select CRC32
 	help
-- 
2.23.0

Re: [PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[Timur Tabi]

On 11/28/19 8:55 AM, Rasmus Villemoes wrote:
> There have been several attempts in the past few years to allow
> building the QUICC engine drivers for platforms other than PPC32. This
> is yet another attempt.
> 
> v5 can be found here:https://lore.kernel.org/lkml/20191118112324.22725-1-linux@rasmusvillemoes.dk/

If it helps:

Entire series:
Acked-by: Timur Tabi <timur@kernel.org>

I've worked on all code covered by this patchset except for the hdlc 
driver.  I don't know if my ACKs are acceptable to everyone, but you 
have them regardless.

Re: [PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[Rasmus Villemoes]

On 01/12/2019 17.10, Timur Tabi wrote:
> On 11/28/19 8:55 AM, Rasmus Villemoes wrote:
>> There have been several attempts in the past few years to allow
>> building the QUICC engine drivers for platforms other than PPC32. This
>> is yet another attempt.
>>
>> v5 can be found
>> here:https://lore.kernel.org/lkml/20191118112324.22725-1-linux@rasmusvillemoes.dk/
>>
> 
> If it helps:
> 
> Entire series:
> Acked-by: Timur Tabi <timur@kernel.org>

Thanks. I'll leave it to Li Yang whether to apply that - they already
all (except for the last-minute build fix) have your R-b.

Li Yang, any chance you could pick up these patches so they have plenty
of time in -next until 5.6?

Thanks,
Rasmus

Re: [PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[Li Yang]

On Mon, Dec 2, 2019 at 2:14 AM Rasmus Villemoes
<linux@rasmusvillemoes.dk> wrote:
>
> On 01/12/2019 17.10, Timur Tabi wrote:
> > On 11/28/19 8:55 AM, Rasmus Villemoes wrote:
> >> There have been several attempts in the past few years to allow
> >> building the QUICC engine drivers for platforms other than PPC32. This
> >> is yet another attempt.
> >>
> >> v5 can be found
> >> here:https://lore.kernel.org/lkml/20191118112324.22725-1-linux@rasmusvillemoes.dk/
> >>
> >
> > If it helps:
> >
> > Entire series:
> > Acked-by: Timur Tabi <timur@kernel.org>
>
> Thanks. I'll leave it to Li Yang whether to apply that - they already
> all (except for the last-minute build fix) have your R-b.
>
> Li Yang, any chance you could pick up these patches so they have plenty
> of time in -next until 5.6?

Sure.  I will.  I'm waiting for the Ack from David on the networking side.

Regards,
Leo

Re: [PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[David Miller]

From: Li Yang <leoyang.li@nxp.com>
Date: Mon, 2 Dec 2019 16:56:39 -0600

> On Mon, Dec 2, 2019 at 2:14 AM Rasmus Villemoes
> <linux@rasmusvillemoes.dk> wrote:
>>
>> On 01/12/2019 17.10, Timur Tabi wrote:
>> > On 11/28/19 8:55 AM, Rasmus Villemoes wrote:
>> >> There have been several attempts in the past few years to allow
>> >> building the QUICC engine drivers for platforms other than PPC32. This
>> >> is yet another attempt.
>> >>
>> >> v5 can be found
>> >> here:https://lore.kernel.org/lkml/20191118112324.22725-1-linux@rasmusvillemoes.dk/
>> >>
>> >
>> > If it helps:
>> >
>> > Entire series:
>> > Acked-by: Timur Tabi <timur@kernel.org>
>>
>> Thanks. I'll leave it to Li Yang whether to apply that - they already
>> all (except for the last-minute build fix) have your R-b.
>>
>> Li Yang, any chance you could pick up these patches so they have plenty
>> of time in -next until 5.6?
> 
> Sure.  I will.  I'm waiting for the Ack from David on the networking side.

Acked-by: David S. Miller <davem@davemloft.net>

Re: [PATCH v6 00/49] QUICC Engine support on ARM, ARM64, PPC64

[Li Yang]

On Thu, Nov 28, 2019 at 8:59 AM Rasmus Villemoes
<linux@rasmusvillemoes.dk> wrote:
>
> There have been several attempts in the past few years to allow
> building the QUICC engine drivers for platforms other than PPC32. This
> is yet another attempt.
>
> v5 can be found here: https://lore.kernel.org/lkml/20191118112324.22725-1-linux@rasmusvillemoes.dk/
>
> Changes in v6:
>
> - add various R-b, A-b tags
>
> - add a patch (48/49) fixing a build issue on ARM with CONFIG_SMP=y
>
> I added that patch last in the series, apart from the "allow to build
> on ARM" Kconfig change, to preserve the enumeration of the other
> patches from v5.
>
> 1-5 are about replacing in_be32 etc. in the core QE code (drivers/soc/fsl/qe).
>
> 6-8 handle miscellaneous other ppcisms.
>
> 9-21 deal with qe_ic: Simplifying the driver significantly by removing
> unused code, and removing the platform-specific initialization from
> arch/powerpc/.
>
> 22-25 deal with raw access to devicetree properties in native endianness.
>
> 26-34 makes drivers/tty/serial/ucc_uart.c (CONFIG_SERIAL_QE) ready to build on non-ppc.
>
> 35-46 deal with IS_ERR_VALUE() and some other things found while
> digging around that part of the code.
>
> 47 adds a PPC32 dependency to UCC_GETH - it has some of the same
> issues that have been fixed in the ucc_uart and ucc_hdlc cases. Nobody
> has requested that I allow that driver to be built for arm{,64} and
> reportedly, the hardware has only ever shipped on PPC SOCs. So instead
> of growing this series even bigger, I kept that addition. It's trivial
> to remove if somebody cares enough to fix the build errors/warnings
> and actually has a platform to test the result on.
>
> 48 fixes a build issue on ARM reported by the kbuild bot.
>
> Finally patch 49 lifts the PPC32 restriction from QUICC_ENGINE. At the
> request of Li Yang, it doesn't remove the PPC32 dependency but instead
> changes it to PPC|| ARM || ARM64 (or COMPILE_TEST), i.e. listing
> the platforms that may have a QE.
>
> The series has been built and booted on both an mpc8309-based platform
> (ppc) as well as an ls1021a-based platform (arm). The core QE code is
> exercised on both, while I could only test the ucc_uart on arm, since
> the uarts are not wired up on our mpc8309 board. Qiang Zhao reports
> that the ucc_hdlc driver does indeed work on a ls1043ardb (arm64)
> board.

Series applied for next on my soc tree.  Thanks!

Regards,
Leo
>
> Rasmus Villemoes (49):
>   soc: fsl: qe: remove space-before-tab
>   soc: fsl: qe: drop volatile qualifier of struct qe_ic::regs
>   soc: fsl: qe: rename qe_(clr/set/clrset)bit* helpers
>   soc: fsl: qe: introduce qe_io{read,write}* wrappers
>   soc: fsl: qe: avoid ppc-specific io accessors
>   soc: fsl: qe: replace spin_event_timeout by readx_poll_timeout_atomic
>   soc: fsl: qe: qe.c: guard use of pvr_version_is() with CONFIG_PPC32
>   soc: fsl: qe: drop unneeded #includes
>   soc: fsl: qe: drop assign-only high_active in qe_ic_init
>   soc: fsl: qe: remove pointless sysfs registration in qe_ic.c
>   soc: fsl: qe: use qe_ic_cascade_{low,high}_mpic also on 83xx
>   soc: fsl: qe: move calls of qe_ic_init out of arch/powerpc/
>   powerpc/83xx: remove mpc83xx_ipic_and_qe_init_IRQ
>   powerpc/85xx: remove mostly pointless mpc85xx_qe_init()
>   soc: fsl: qe: move qe_ic_cascade_* functions to qe_ic.c
>   soc: fsl: qe: rename qe_ic_cascade_low_mpic -> qe_ic_cascade_low
>   soc: fsl: qe: remove unused qe_ic_set_* functions
>   soc: fsl: qe: don't use NO_IRQ in qe_ic.c
>   soc: fsl: qe: make qe_ic_get_{low,high}_irq static
>   soc: fsl: qe: simplify qe_ic_init()
>   soc: fsl: qe: merge qe_ic.h headers into qe_ic.c
>   soc: fsl: qe: qe.c: use of_property_read_* helpers
>   soc: fsl: qe: qe_io.c: don't open-code of_parse_phandle()
>   soc: fsl: qe: qe_io.c: access device tree property using be32_to_cpu
>   soc: fsl: qe: qe_io.c: use of_property_read_u32() in par_io_init()
>   soc: fsl: move cpm.h from powerpc/include/asm to include/soc/fsl
>   soc/fsl/qe/qe.h: update include path for cpm.h
>   serial: ucc_uart: explicitly include soc/fsl/cpm.h
>   serial: ucc_uart: replace ppc-specific IO accessors
>   serial: ucc_uart: factor out soft_uart initialization
>   serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
>   serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
>   serial: ucc_uart: limit brg-frequency workaround to PPC32
>   serial: ucc_uart: access __be32 field using be32_to_cpu
>   soc: fsl: qe: change return type of cpm_muram_alloc() to s32
>   soc: fsl: qe: make cpm_muram_free() return void
>   soc: fsl: qe: make cpm_muram_free() ignore a negative offset
>   soc: fsl: qe: drop broken lazy call of cpm_muram_init()
>   soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error
>     path
>   soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
>   soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
>   soc: fsl: qe: drop pointless check in qe_sdma_init()
>   soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
>   net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
>   net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
>   net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
>   net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
>   soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
>   soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE
>
>  arch/powerpc/include/asm/cpm.h                | 172 +-------
>  arch/powerpc/platforms/83xx/km83xx.c          |   3 +-
>  arch/powerpc/platforms/83xx/misc.c            |  23 --
>  arch/powerpc/platforms/83xx/mpc832x_mds.c     |   3 +-
>  arch/powerpc/platforms/83xx/mpc832x_rdb.c     |   3 +-
>  arch/powerpc/platforms/83xx/mpc836x_mds.c     |   3 +-
>  arch/powerpc/platforms/83xx/mpc836x_rdk.c     |   3 +-
>  arch/powerpc/platforms/83xx/mpc83xx.h         |   7 -
>  arch/powerpc/platforms/85xx/common.c          |  23 --
>  arch/powerpc/platforms/85xx/corenet_generic.c |  12 -
>  arch/powerpc/platforms/85xx/mpc85xx.h         |   2 -
>  arch/powerpc/platforms/85xx/mpc85xx_mds.c     |  28 --
>  arch/powerpc/platforms/85xx/mpc85xx_rdb.c     |  18 -
>  arch/powerpc/platforms/85xx/twr_p102x.c       |  16 -
>  drivers/net/ethernet/freescale/Kconfig        |   2 +-
>  drivers/net/wan/fsl_ucc_hdlc.c                |  23 +-
>  drivers/net/wan/fsl_ucc_hdlc.h                |   2 +-
>  drivers/soc/fsl/qe/Kconfig                    |   3 +-
>  drivers/soc/fsl/qe/gpio.c                     |  34 +-
>  drivers/soc/fsl/qe/qe.c                       | 104 ++---
>  drivers/soc/fsl/qe/qe_common.c                |  50 +--
>  drivers/soc/fsl/qe/qe_ic.c                    | 285 ++++++-------
>  drivers/soc/fsl/qe/qe_ic.h                    |  99 -----
>  drivers/soc/fsl/qe/qe_io.c                    |  70 ++--
>  drivers/soc/fsl/qe/qe_tdm.c                   |   8 +-
>  drivers/soc/fsl/qe/ucc.c                      |  27 +-
>  drivers/soc/fsl/qe/ucc_fast.c                 |  86 ++--
>  drivers/soc/fsl/qe/ucc_slow.c                 |  60 ++-
>  drivers/soc/fsl/qe/usb.c                      |   2 +-
>  drivers/tty/serial/ucc_uart.c                 | 385 +++++++++---------
>  include/soc/fsl/cpm.h                         | 171 ++++++++
>  include/soc/fsl/qe/qe.h                       |  59 ++-
>  include/soc/fsl/qe/qe_ic.h                    | 135 ------
>  include/soc/fsl/qe/ucc_fast.h                 |   4 +-
>  include/soc/fsl/qe/ucc_slow.h                 |   6 +-
>  35 files changed, 775 insertions(+), 1156 deletions(-)
>  delete mode 100644 drivers/soc/fsl/qe/qe_ic.h
>  create mode 100644 include/soc/fsl/cpm.h
>  delete mode 100644 include/soc/fsl/qe/qe_ic.h
>
> --
> 2.23.0
>