* [PATCH v6 2/4] dt-bindings: regulator: add document bindings for mpq7920
2020-01-09 11:25 [PATCH v6 0/4] Add regulator support for mpq7920 Saravanan Sekar
2020-01-09 11:25 ` [PATCH v6 1/4] dt-bindings: Add an entry for Monolithic Power System, MPS Saravanan Sekar
@ 2020-01-09 11:25 ` Saravanan Sekar
2020-01-13 16:56 ` Rob Herring
2020-01-09 11:25 ` [PATCH v6 3/4] regulator: mpq7920: add mpq7920 regulator driver Saravanan Sekar
2020-01-09 11:25 ` [PATCH v6 4/4] MAINTAINERS: Add entry for mpq7920 PMIC driver Saravanan Sekar
3 siblings, 1 reply; 12+ messages in thread
From: Saravanan Sekar @ 2020-01-09 11:25 UTC (permalink / raw)
To: sravanhome, lgirdwood, broonie, robh+dt, mark.rutland, mripard,
shawnguo, heiko, sam, icenowy, laurent.pinchart, gregkh,
Jonathan.Cameron, davem, mchehab+samsung
Cc: devicetree, linux-kernel
Add device tree binding information for mpq7920 regulator driver.
Example bindings for mpq7920 are added.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
---
.../bindings/regulator/mps,mpq7920.yaml | 202 ++++++++++++++++++
1 file changed, 202 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/mps,mpq7920.yaml
diff --git a/Documentation/devicetree/bindings/regulator/mps,mpq7920.yaml b/Documentation/devicetree/bindings/regulator/mps,mpq7920.yaml
new file mode 100644
index 000000000000..598f3ea070c9
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mps,mpq7920.yaml
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/mps,mpq7920.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Monolithic Power System MPQ7920 PMIC
+
+maintainers:
+ - Saravanan Sekar <sravanhome@gmail.com>
+
+properties:
+ $nodename:
+ pattern: "pmic@[0-9a-f]{1,2}"
+ compatible:
+ enum:
+ - mps,mpq7920
+
+ reg:
+ maxItems: 1
+
+ regulators:
+ type: object
+ description: |
+ list of regulators provided by this controller, must be named
+ after their hardware counterparts BUCK[1-4], one LDORTC, and LDO[2-5]
+
+ mps,switch-freq:
+ description: |
+ switching frequency must be one of following corresponding value
+ 1.1MHz, 1.65MHz, 2.2MHz, 2.75MHz
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 2
+
+ buck1:
+ type: object
+ $ref: "regulator.yaml#"
+ description: |
+ 4.5A DC-DC step down converter
+
+ mps,buck-softstart:
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+ description: |
+ defines the soft start time of this buck, must be one of the following
+ corresponding values 150us, 300us, 610us, 920us
+
+ mps,buck-phase-delay:
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 0
+ description: |
+ defines the phase delay of this buck, must be one of the following
+ corresponding values 0deg, 90deg, 180deg, 270deg
+
+ mps,buck-ovp-disable:
+ type: boolean
+ description: |
+ disables over voltage protection of this buck
+
+ buck2:
+ type: object
+ $ref: "regulator.yaml#"
+ description: |
+ 2.5A DC-DC step down converter
+
+ mps,buck-softstart:
+ description: |
+ defines the soft start time of this buck, must be one of the following
+ corresponding values 150us, 300us, 610us, 920us
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+
+ mps,buck-phase-delay:
+ description: |
+ defines the phase delay of this buck, must be one of the following
+ corresponding values 0deg, 90deg, 180deg, 270deg
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 0
+
+ mps,buck-ovp-disable:
+ description: |
+ disables over voltage protection of this buck
+ type: boolean
+
+ buck3:
+ type: object
+ $ref: "regulator.yaml#"
+ description: |
+ 4.5A DC-DC step down converter
+
+ mps,buck-softstart:
+ description: |
+ defines the soft start time of this buck, must be one of the following
+ corresponding values 150us, 300us, 610us, 920us
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+
+ mps,buck-phase-delay:
+ description: |
+ defines the phase delay of this buck, must be one of the following
+ corresponding values 0deg, 90deg, 180deg, 270deg
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+
+ mps,buck-ovp-disable:
+ description: |
+ disables over voltage protection of this buck
+ type: boolean
+
+ buck4:
+ type: object
+ $ref: "regulator.yaml#"
+ description: |
+ 2.5A DC-DC step down converter
+
+ mps,buck-softstart:
+ description: |
+ defines the soft start time of this buck, must be one of the following
+ corresponding values 150us, 300us, 610us, 920us
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+
+ mps,buck-phase-delay:
+ description: |
+ defines the phase delay of this buck, must be one of the following
+ corresponding values 0deg, 90deg, 180deg, 270deg
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [ 0, 1, 2, 3 ]
+ default: 1
+
+ mps,buck-ovp-disable:
+ description: |
+ disables over voltage protection of this buck
+ type: boolean
+
+ ldortc:
+ $ref: "regulator.yaml#"
+ description: |
+ regulator with 0.65V-3.5875V for RTC, always enabled
+
+ ldo2:
+ $ref: "regulator.yaml#"
+ description: |
+ regulator with 0.65V-3.5875V
+
+ ldo3:
+ $ref: "regulator.yaml#"
+ description: |
+ regulator with 0.65V-3.5875V
+
+ ldo4:
+ $ref: "regulator.yaml#"
+ description: |
+ regulator with 0.65V-3.5875V
+
+ ldo5:
+ $ref: "regulator.yaml#"
+ description: |
+ regulator with 0.65V-3.5875V
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@69 {
+ compatible = "mps,mpq7920";
+ reg = <0x69>;
+
+ regulators {
+ mps,switch-freq = <1>;
+
+ buck1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <3587500>;
+ regulator-min-microamp = <460000>;
+ regulator-max-microamp = <7600000>;
+ regulator-boot-on;
+ mps,buck-ovp-disable;
+ mps,buck-phase-delay = <2>;
+ mps,buck-softstart = <1>;
+ };
+
+ ldo2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <3587500>;
+ };
+ };
+ };
+ };
+...
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v6 3/4] regulator: mpq7920: add mpq7920 regulator driver
2020-01-09 11:25 [PATCH v6 0/4] Add regulator support for mpq7920 Saravanan Sekar
2020-01-09 11:25 ` [PATCH v6 1/4] dt-bindings: Add an entry for Monolithic Power System, MPS Saravanan Sekar
2020-01-09 11:25 ` [PATCH v6 2/4] dt-bindings: regulator: add document bindings for mpq7920 Saravanan Sekar
@ 2020-01-09 11:25 ` Saravanan Sekar
2020-01-09 13:28 ` Mark Brown
2020-01-09 11:25 ` [PATCH v6 4/4] MAINTAINERS: Add entry for mpq7920 PMIC driver Saravanan Sekar
3 siblings, 1 reply; 12+ messages in thread
From: Saravanan Sekar @ 2020-01-09 11:25 UTC (permalink / raw)
To: sravanhome, lgirdwood, broonie, robh+dt, mark.rutland, mripard,
shawnguo, heiko, sam, icenowy, laurent.pinchart, gregkh,
Jonathan.Cameron, davem, mchehab+samsung
Cc: devicetree, linux-kernel
Adding regulator driver for the device mpq7920.
The MPQ7920 PMIC device contains four DC-DC buck converters and
five regulators, is designed for automotive and accessed over I2C.
Fixed sparse warning reported on this patch
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
---
drivers/regulator/Kconfig | 10 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/mpq7920.c | 346 ++++++++++++++++++++++++++++++++++++
drivers/regulator/mpq7920.h | 68 +++++++
4 files changed, 425 insertions(+)
create mode 100644 drivers/regulator/mpq7920.c
create mode 100644 drivers/regulator/mpq7920.h
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 74eb5af7295f..e10adc2e57da 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -600,6 +600,16 @@ config REGULATOR_MCP16502
through the regulator interface. In addition it enables
suspend-to-ram/standby transition.
+config REGULATOR_MPQ7920
+ tristate "Monolithic MPQ7920 PMIC"
+ depends on I2C && OF
+ select REGMAP_I2C
+ help
+ Say y here to support the MPQ7920 PMIC. This will enable supports
+ the software controllable 4 buck and 5 LDO regulators.
+ This driver supports the control of different power rails of device
+ through regulator interface.
+
config REGULATOR_MT6311
tristate "MediaTek MT6311 PMIC"
depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 2210ba56f9bd..fd11002507e4 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -77,6 +77,7 @@ obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
+obj-$(CONFIG_REGULATOR_MPQ7920) += mpq7920.o
obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
obj-$(CONFIG_REGULATOR_MT6323) += mt6323-regulator.o
obj-$(CONFIG_REGULATOR_MT6358) += mt6358-regulator.o
diff --git a/drivers/regulator/mpq7920.c b/drivers/regulator/mpq7920.c
new file mode 100644
index 000000000000..c603d60fb87b
--- /dev/null
+++ b/drivers/regulator/mpq7920.c
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// mpq7920.c - regulator driver for mps mpq7920
+//
+// Copyright 2019 Monolithic Power Systems, Inc
+//
+// Author: Saravanan Sekar <sravanhome@gmail.com>
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include "mpq7920.h"
+
+#define MPQ7920_BUCK_VOLT_RANGE \
+ ((MPQ7920_VOLT_MAX - MPQ7920_BUCK_VOLT_MIN)/MPQ7920_VOLT_STEP + 1)
+#define MPQ7920_LDO_VOLT_RANGE \
+ ((MPQ7920_VOLT_MAX - MPQ7920_LDO_VOLT_MIN)/MPQ7920_VOLT_STEP + 1)
+
+#define MPQ7920BUCK(_name, _id, _ilim) \
+ [MPQ7920_BUCK ## _id] = { \
+ .id = MPQ7920_BUCK ## _id, \
+ .name = _name, \
+ .of_match = _name, \
+ .regulators_node = "regulators", \
+ .of_parse_cb = mpq7920_parse_cb, \
+ .ops = &mpq7920_buck_ops, \
+ .min_uV = MPQ7920_BUCK_VOLT_MIN, \
+ .uV_step = MPQ7920_VOLT_STEP, \
+ .n_voltages = MPQ7920_BUCK_VOLT_RANGE, \
+ .curr_table = _ilim, \
+ .n_current_limits = ARRAY_SIZE(_ilim), \
+ .csel_reg = MPQ7920_BUCK ##_id## _REG_C, \
+ .csel_mask = MPQ7920_MASK_BUCK_ILIM, \
+ .enable_reg = MPQ7920_REG_REGULATOR_EN, \
+ .enable_mask = BIT(MPQ7920_REGULATOR_EN_OFFSET - \
+ MPQ7920_BUCK ## _id), \
+ .vsel_reg = MPQ7920_BUCK ##_id## _REG_A, \
+ .vsel_mask = MPQ7920_MASK_VREF, \
+ .active_discharge_on = MPQ7920_DISCHARGE_ON, \
+ .active_discharge_reg = MPQ7920_BUCK ##_id## _REG_B, \
+ .active_discharge_mask = MPQ7920_MASK_DISCHARGE, \
+ .soft_start_reg = MPQ7920_BUCK ##_id## _REG_C, \
+ .soft_start_mask = MPQ7920_MASK_SOFTSTART, \
+ .owner = THIS_MODULE, \
+ }
+
+#define MPQ7920LDO(_name, _id, _ops, _ilim, _ilim_sz, _creg, _cmask) \
+ [MPQ7920_LDO ## _id] = { \
+ .id = MPQ7920_LDO ## _id, \
+ .name = _name, \
+ .of_match = _name, \
+ .regulators_node = "regulators", \
+ .ops = _ops, \
+ .min_uV = MPQ7920_LDO_VOLT_MIN, \
+ .uV_step = MPQ7920_VOLT_STEP, \
+ .n_voltages = MPQ7920_LDO_VOLT_RANGE, \
+ .vsel_reg = MPQ7920_LDO ##_id## _REG_A, \
+ .vsel_mask = MPQ7920_MASK_VREF, \
+ .curr_table = _ilim, \
+ .n_current_limits = _ilim_sz, \
+ .csel_reg = _creg, \
+ .csel_mask = _cmask, \
+ .enable_reg = (_id == 1) ? 0 : MPQ7920_REG_REGULATOR_EN,\
+ .enable_mask = BIT(MPQ7920_REGULATOR_EN_OFFSET - \
+ MPQ7920_LDO ##_id + 1), \
+ .active_discharge_on = MPQ7920_DISCHARGE_ON, \
+ .active_discharge_mask = MPQ7920_MASK_DISCHARGE, \
+ .active_discharge_reg = MPQ7920_LDO ##_id## _REG_B, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ }
+
+enum mpq7920_regulators {
+ MPQ7920_BUCK1,
+ MPQ7920_BUCK2,
+ MPQ7920_BUCK3,
+ MPQ7920_BUCK4,
+ MPQ7920_LDO1, /* LDORTC */
+ MPQ7920_LDO2,
+ MPQ7920_LDO3,
+ MPQ7920_LDO4,
+ MPQ7920_LDO5,
+ MPQ7920_MAX_REGULATORS,
+};
+
+struct mpq7920_regulator_info {
+ struct device *dev;
+ struct regmap *regmap;
+ struct regulator_dev *rdev[MPQ7920_MAX_REGULATORS];
+ struct regulator_desc *rdesc;
+};
+
+static const struct regmap_config mpq7920_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = 0x25,
+};
+
+/* Current limits array (in uA)
+ * ILIM1 & ILIM3
+ */
+static const unsigned int mpq7920_I_limits1[] = {
+ 4600000, 6600000, 7600000, 9300000
+};
+
+/* ILIM2 & ILIM4 */
+static const unsigned int mpq7920_I_limits2[] = {
+ 2700000, 3900000, 5100000, 6100000
+};
+
+/* LDO4 & LDO5 */
+static const unsigned int mpq7920_I_limits3[] = {
+ 300000, 700000
+};
+
+static int mpq7920_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay);
+static int mpq7920_parse_cb(struct device_node *np,
+ const struct regulator_desc *rdesc,
+ struct regulator_config *config);
+
+/* RTCLDO not controllable, always ON */
+static const struct regulator_ops mpq7920_ldortc_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+};
+
+static const struct regulator_ops mpq7920_ldo_wo_current_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
+static const struct regulator_ops mpq7920_ldo_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+ .get_current_limit = regulator_get_current_limit_regmap,
+ .set_current_limit = regulator_set_current_limit_regmap,
+};
+
+static const struct regulator_ops mpq7920_buck_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+ .set_soft_start = regulator_set_soft_start_regmap,
+ .set_ramp_delay = mpq7920_set_ramp_delay,
+};
+
+static struct regulator_desc mpq7920_regulators_desc[MPQ7920_MAX_REGULATORS] = {
+ MPQ7920BUCK("buck1", 1, mpq7920_I_limits1),
+ MPQ7920BUCK("buck2", 2, mpq7920_I_limits2),
+ MPQ7920BUCK("buck3", 3, mpq7920_I_limits1),
+ MPQ7920BUCK("buck4", 4, mpq7920_I_limits2),
+ MPQ7920LDO("ldortc", 1, &mpq7920_ldortc_ops, NULL, 0, 0, 0),
+ MPQ7920LDO("ldo2", 2, &mpq7920_ldo_wo_current_ops, NULL, 0, 0, 0),
+ MPQ7920LDO("ldo3", 3, &mpq7920_ldo_wo_current_ops, NULL, 0, 0, 0),
+ MPQ7920LDO("ldo4", 4, &mpq7920_ldo_ops, mpq7920_I_limits3,
+ ARRAY_SIZE(mpq7920_I_limits3), MPQ7920_LDO4_REG_B,
+ MPQ7920_MASK_LDO_ILIM),
+ MPQ7920LDO("ldo5", 5, &mpq7920_ldo_ops, mpq7920_I_limits3,
+ ARRAY_SIZE(mpq7920_I_limits3), MPQ7920_LDO5_REG_B,
+ MPQ7920_MASK_LDO_ILIM),
+};
+
+/*
+ * DVS ramp rate BUCK1 to BUCK4
+ * 00-01: Reserved
+ * 10: 8mV/us
+ * 11: 4mV/us
+ */
+static int mpq7920_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
+{
+ unsigned int ramp_val;
+
+ if (ramp_delay > 8000 || ramp_delay < 0)
+ return -EINVAL;
+
+ if (ramp_delay <= 4000)
+ ramp_val = 3;
+ else
+ ramp_val = 2;
+
+ return regmap_update_bits(rdev->regmap, MPQ7920_REG_CTL0,
+ MPQ7920_MASK_DVS_SLEWRATE, ramp_val << 6);
+}
+
+static int mpq7920_parse_cb(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ uint8_t val;
+ int ret;
+ struct mpq7920_regulator_info *info = config->driver_data;
+ struct regulator_desc *rdesc = &info->rdesc[desc->id];
+
+ if (of_property_read_bool(np, "mps,buck-ovp-disable")) {
+ regmap_update_bits(config->regmap,
+ MPQ7920_BUCK1_REG_B + (rdesc->id * 4),
+ BIT(6), ~BIT(6));
+ }
+
+ ret = of_property_read_u8(np, "mps,buck-phase-delay", &val);
+ if (!ret) {
+ regmap_update_bits(config->regmap,
+ MPQ7920_BUCK1_REG_C + (rdesc->id * 4),
+ MPQ7920_MASK_BUCK_PHASE_DEALY,
+ (val & 3) << 4);
+ }
+
+ ret = of_property_read_u8(np, "mps,buck-softstart", &val);
+ if (!ret)
+ rdesc->soft_start_val_on = (val & 3) << 2;
+
+ return 0;
+}
+
+static void mpq7920_parse_dt(struct device *dev,
+ struct mpq7920_regulator_info *info)
+{
+ int ret;
+ struct device_node *np = dev->of_node;
+ uint8_t freq;
+
+ np = of_get_child_by_name(np, "regulators");
+ if (!np) {
+ dev_err(dev, "missing 'regulators' subnode in DT\n");
+ return;
+ }
+
+ ret = of_property_read_u8(np, "mps,switch-freq", &freq);
+ if (!ret) {
+ regmap_update_bits(info->regmap, MPQ7920_REG_CTL0,
+ MPQ7920_MASK_SWITCH_FREQ,
+ (freq & 3) << 4);
+ }
+
+ of_node_put(np);
+}
+
+static inline int mpq7920_regulator_register(
+ struct mpq7920_regulator_info *info,
+ struct regulator_config *config)
+{
+ int i;
+ struct regulator_desc *rdesc;
+
+ for (i = 0; i < MPQ7920_MAX_REGULATORS; i++) {
+ rdesc = &info->rdesc[i];
+
+ info->rdev[i] = devm_regulator_register(info->dev, rdesc,
+ config);
+ if (IS_ERR(info->rdev))
+ return PTR_ERR(info->rdev);
+ }
+
+ return 0;
+}
+
+static int mpq7920_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct mpq7920_regulator_info *info;
+ struct regulator_config config = { NULL, };
+ struct regmap *regmap;
+ int ret;
+
+ info = devm_kzalloc(dev, sizeof(struct mpq7920_regulator_info),
+ GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ info->dev = dev;
+ info->rdesc = mpq7920_regulators_desc;
+ regmap = devm_regmap_init_i2c(client, &mpq7920_regmap_config);
+ if (IS_ERR(regmap)) {
+ dev_err(dev, "Failed to allocate regmap!\n");
+ return PTR_ERR(regmap);
+ }
+
+ i2c_set_clientdata(client, info);
+ info->regmap = regmap;
+ if (client->dev.of_node)
+ mpq7920_parse_dt(&client->dev, info);
+
+ config.dev = info->dev;
+ config.regmap = regmap;
+ config.driver_data = info;
+
+ ret = mpq7920_regulator_register(info, &config);
+ if (ret < 0)
+ dev_err(dev, "Failed to register regulator!\n");
+
+ return ret;
+}
+
+static const struct of_device_id mpq7920_of_match[] = {
+ { .compatible = "mps,mpq7920"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, mpq7920_of_match);
+
+static const struct i2c_device_id mpq7920_id[] = {
+ { "mpq7920", },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, mpq7920_id);
+
+static struct i2c_driver mpq7920_regulator_driver = {
+ .driver = {
+ .name = "mpq7920",
+ .of_match_table = of_match_ptr(mpq7920_of_match),
+ },
+ .probe = mpq7920_i2c_probe,
+ .id_table = mpq7920_id,
+};
+module_i2c_driver(mpq7920_regulator_driver);
+
+MODULE_AUTHOR("Saravanan Sekar <sravanhome@gmail.com>");
+MODULE_DESCRIPTION("MPQ7920 PMIC regulator driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/mpq7920.h b/drivers/regulator/mpq7920.h
new file mode 100644
index 000000000000..6a93bfbc750c
--- /dev/null
+++ b/drivers/regulator/mpq7920.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * mpq7920.h - Regulator definitions for mpq7920
+ *
+ * Copyright 2019 Monolithic Power Systems, Inc
+ *
+ */
+
+#ifndef __MPQ7920_H__
+#define __MPQ7920_H__
+
+#define MPQ7920_REG_CTL0 0x00
+#define MPQ7920_REG_CTL1 0x01
+#define MPQ7920_REG_CTL2 0x02
+#define MPQ7920_BUCK1_REG_A 0x03
+#define MPQ7920_BUCK1_REG_B 0x04
+#define MPQ7920_BUCK1_REG_C 0x05
+#define MPQ7920_BUCK1_REG_D 0x06
+#define MPQ7920_BUCK2_REG_A 0x07
+#define MPQ7920_BUCK2_REG_B 0x08
+#define MPQ7920_BUCK2_REG_C 0x09
+#define MPQ7920_BUCK2_REG_D 0x0a
+#define MPQ7920_BUCK3_REG_A 0x0b
+#define MPQ7920_BUCK3_REG_B 0x0c
+#define MPQ7920_BUCK3_REG_C 0x0d
+#define MPQ7920_BUCK3_REG_D 0x0e
+#define MPQ7920_BUCK4_REG_A 0x0f
+#define MPQ7920_BUCK4_REG_B 0x10
+#define MPQ7920_BUCK4_REG_C 0x11
+#define MPQ7920_BUCK4_REG_D 0x12
+#define MPQ7920_LDO1_REG_A 0x13
+#define MPQ7920_LDO1_REG_B 0x0
+#define MPQ7920_LDO2_REG_A 0x14
+#define MPQ7920_LDO2_REG_B 0x15
+#define MPQ7920_LDO2_REG_C 0x16
+#define MPQ7920_LDO3_REG_A 0x17
+#define MPQ7920_LDO3_REG_B 0x18
+#define MPQ7920_LDO3_REG_C 0x19
+#define MPQ7920_LDO4_REG_A 0x1a
+#define MPQ7920_LDO4_REG_B 0x1b
+#define MPQ7920_LDO4_REG_C 0x1c
+#define MPQ7920_LDO5_REG_A 0x1d
+#define MPQ7920_LDO5_REG_B 0x1e
+#define MPQ7920_LDO5_REG_C 0x1f
+#define MPQ7920_REG_MODE 0x20
+#define MPQ7920_REG_REGULATOR_EN1 0x22
+#define MPQ7920_REG_REGULATOR_EN 0x22
+
+#define MPQ7920_MASK_VREF 0x7f
+#define MPQ7920_MASK_BUCK_ILIM 0xd0
+#define MPQ7920_MASK_LDO_ILIM BIT(6)
+#define MPQ7920_MASK_DISCHARGE BIT(5)
+#define MPQ7920_MASK_MODE 0xc0
+#define MPQ7920_MASK_SOFTSTART 0x0c
+#define MPQ7920_MASK_SWITCH_FREQ 0x30
+#define MPQ7920_MASK_BUCK_PHASE_DEALY 0x30
+#define MPQ7920_MASK_DVS_SLEWRATE 0xc0
+#define MPQ7920_DISCHARGE_ON 0x1
+
+#define MPQ7920_REGULATOR_EN_OFFSET 7
+
+/* values in mV */
+#define MPQ7920_BUCK_VOLT_MIN 400000
+#define MPQ7920_LDO_VOLT_MIN 650000
+#define MPQ7920_VOLT_MAX 3587500
+#define MPQ7920_VOLT_STEP 12500
+
+#endif /* __MPQ7920_H__ */
--
2.17.1
^ permalink raw reply related [flat|nested] 12+ messages in thread