From: Grygorii Strashko <grygorii.strashko@ti.com>
To: Rob Herring <robh+dt@kernel.org>, Tero Kristo <t-kristo@ti.com>,
"David S . Miller" <davem@davemloft.net>,
netdev <netdev@vger.kernel.org>, Roger Quadros <rogerq@ti.com>,
<devicetree@vger.kernel.org>, Jakub Kicinski <kuba@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>,
Sekhar Nori <nsekhar@ti.com>,
Peter Ujfalusi <peter.ujfalusi@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
<linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
Grygorii Strashko <grygorii.strashko@ti.com>
Subject: [PATCH net-next v3 03/10] net: ethernet: ti: ale: am65: add support for default thread cfg
Date: Fri, 13 Mar 2020 19:55:04 +0200 [thread overview]
Message-ID: <20200313175511.2155-4-grygorii.strashko@ti.com> (raw)
In-Reply-To: <20200313175511.2155-1-grygorii.strashko@ti.com>
Add support for default thread configuration for AM65x CPSW NUSS ALE to
allow route all ingress packets to one default RX UDMA flow.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/net/ethernet/ti/cpsw_ale.c | 18 ++++++++++++++++++
drivers/net/ethernet/ti/cpsw_ale.h | 2 ++
2 files changed, 20 insertions(+)
diff --git a/drivers/net/ethernet/ti/cpsw_ale.c b/drivers/net/ethernet/ti/cpsw_ale.c
index 719e7846127c..0374e6936091 100644
--- a/drivers/net/ethernet/ti/cpsw_ale.c
+++ b/drivers/net/ethernet/ti/cpsw_ale.c
@@ -44,6 +44,8 @@
#define ALE_UNKNOWNVLAN_FORCE_UNTAG_EGRESS 0x9C
#define ALE_VLAN_MASK_MUX(reg) (0xc0 + (0x4 * (reg)))
+#define AM65_CPSW_ALE_THREAD_DEF_REG 0x134
+
#define ALE_TABLE_WRITE BIT(31)
#define ALE_TYPE_FREE 0
@@ -843,6 +845,22 @@ static struct ale_control_info ale_controls[ALE_NUM_CONTROLS] = {
.port_shift = 0,
.bits = 6,
},
+ [ALE_DEFAULT_THREAD_ID] = {
+ .name = "default_thread_id",
+ .offset = AM65_CPSW_ALE_THREAD_DEF_REG,
+ .port_offset = 0,
+ .shift = 0,
+ .port_shift = 0,
+ .bits = 6,
+ },
+ [ALE_DEFAULT_THREAD_ENABLE] = {
+ .name = "default_thread_id_enable",
+ .offset = AM65_CPSW_ALE_THREAD_DEF_REG,
+ .port_offset = 0,
+ .shift = 15,
+ .port_shift = 0,
+ .bits = 1,
+ },
};
int cpsw_ale_control_set(struct cpsw_ale *ale, int port, int control,
diff --git a/drivers/net/ethernet/ti/cpsw_ale.h b/drivers/net/ethernet/ti/cpsw_ale.h
index eaca73c17ae7..6a3cb6898728 100644
--- a/drivers/net/ethernet/ti/cpsw_ale.h
+++ b/drivers/net/ethernet/ti/cpsw_ale.h
@@ -66,6 +66,8 @@ enum cpsw_ale_control {
ALE_PORT_MACONLY_CAF,
ALE_PORT_BCAST_LIMIT,
ALE_PORT_MCAST_LIMIT,
+ ALE_DEFAULT_THREAD_ID,
+ ALE_DEFAULT_THREAD_ENABLE,
ALE_NUM_CONTROLS,
};
--
2.17.1
next prev parent reply other threads:[~2020-03-13 17:55 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-13 17:55 [PATCH net-next v3 00/10] net: ethernet: ti: add networking support for k3 am65x/j721e soc Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 01/10] net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 02/10] net: ethernet: ti: ale: add support for mac-only mode Grygorii Strashko
2020-03-13 17:55 ` Grygorii Strashko [this message]
2020-03-13 17:55 ` [PATCH net-next v3 04/10] dt-binding: ti: am65x: document mcu cpsw nuss Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 05/10] net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver Grygorii Strashko
2020-03-13 20:04 ` Jakub Kicinski
2020-03-13 17:55 ` [PATCH net-next v3 06/10] arm64: dts: ti: k3-am65-mcu: add cpsw nuss node Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 07/10] arm64: dts: k3-am654-base-board: add mcu cpsw nuss pinmux and phy defs Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 08/10] arm64: dts: ti: k3-j721e-mcu: add mcu cpsw nuss node Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 09/10] arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux and phy defs Grygorii Strashko
2020-03-13 17:55 ` [PATCH net-next v3 10/10] arm64: defconfig: ti: k3: enable dma and networking Grygorii Strashko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200313175511.2155-4-grygorii.strashko@ti.com \
--to=grygorii.strashko@ti.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=m-karicheri2@ti.com \
--cc=netdev@vger.kernel.org \
--cc=nsekhar@ti.com \
--cc=peter.ujfalusi@ti.com \
--cc=robh+dt@kernel.org \
--cc=rogerq@ti.com \
--cc=t-kristo@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).