[PATCH AUTOSEL 5.4 01/35] spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x

[PATCH AUTOSEL 5.4 01/35] spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x

[Sasha Levin]

From: Vignesh Raghavendra <vigneshr@ti.com>

[ Upstream commit e4e8276a4f652be2c7bb783a0155d4adb85f5d7d ]

On AM654, McSPI can only support 4K - 1 bytes per transfer when DMA is
enabled. Therefore populate master->max_transfer_size callback to
inform client drivers of this restriction when DMA channels are
available.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-omap2-mcspi.c                 | 26 +++++++++++++++++++
 include/linux/platform_data/spi-omap2-mcspi.h |  1 +
 2 files changed, 27 insertions(+)

diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 848e03e5f42d5..8e435da730996 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -130,6 +130,7 @@ struct omap2_mcspi {
 	int			fifo_depth;
 	bool			slave_aborted;
 	unsigned int		pin_dir:1;
+	size_t			max_xfer_len;
 };
 
 struct omap2_mcspi_cs {
@@ -1316,6 +1317,18 @@ static bool omap2_mcspi_can_dma(struct spi_master *master,
 	return (xfer->len >= DMA_MIN_BYTES);
 }
 
+static size_t omap2_mcspi_max_xfer_size(struct spi_device *spi)
+{
+	struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master);
+	struct omap2_mcspi_dma *mcspi_dma =
+		&mcspi->dma_channels[spi->chip_select];
+
+	if (mcspi->max_xfer_len && mcspi_dma->dma_rx)
+		return mcspi->max_xfer_len;
+
+	return SIZE_MAX;
+}
+
 static int omap2_mcspi_controller_setup(struct omap2_mcspi *mcspi)
 {
 	struct spi_master	*master = mcspi->master;
@@ -1384,6 +1397,11 @@ static struct omap2_mcspi_platform_config omap4_pdata = {
 	.regs_offset = OMAP4_MCSPI_REG_OFFSET,
 };
 
+static struct omap2_mcspi_platform_config am654_pdata = {
+	.regs_offset = OMAP4_MCSPI_REG_OFFSET,
+	.max_xfer_len = SZ_4K - 1,
+};
+
 static const struct of_device_id omap_mcspi_of_match[] = {
 	{
 		.compatible = "ti,omap2-mcspi",
@@ -1393,6 +1411,10 @@ static const struct of_device_id omap_mcspi_of_match[] = {
 		.compatible = "ti,omap4-mcspi",
 		.data = &omap4_pdata,
 	},
+	{
+		.compatible = "ti,am654-mcspi",
+		.data = &am654_pdata,
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, omap_mcspi_of_match);
@@ -1450,6 +1472,10 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 		mcspi->pin_dir = pdata->pin_dir;
 	}
 	regs_offset = pdata->regs_offset;
+	if (pdata->max_xfer_len) {
+		mcspi->max_xfer_len = pdata->max_xfer_len;
+		master->max_transfer_size = omap2_mcspi_max_xfer_size;
+	}
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	mcspi->base = devm_ioremap_resource(&pdev->dev, r);
diff --git a/include/linux/platform_data/spi-omap2-mcspi.h b/include/linux/platform_data/spi-omap2-mcspi.h
index 0bf9fddb83064..3b400b1919a9b 100644
--- a/include/linux/platform_data/spi-omap2-mcspi.h
+++ b/include/linux/platform_data/spi-omap2-mcspi.h
@@ -11,6 +11,7 @@ struct omap2_mcspi_platform_config {
 	unsigned short	num_cs;
 	unsigned int regs_offset;
 	unsigned int pin_dir:1;
+	size_t max_xfer_len;
 };
 
 struct omap2_mcspi_device_config {
-- 
2.20.1

[PATCH AUTOSEL 5.4 02/35] spi: spi-omap2-mcspi: Support probe deferral for DMA channels

[Sasha Levin]

From: Vignesh Raghavendra <vigneshr@ti.com>

[ Upstream commit 32f2fc5dc3992b4b60cc6b1a6a31be605cc9c3a2 ]

dma_request_channel() can return -EPROBE_DEFER, if DMA driver is not
ready. Currently driver just falls back to PIO mode on probe deferral.
Fix this by requesting all required channels during probe and
propagating EPROBE_DEFER error code.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-omap2-mcspi.c | 77 +++++++++++++++++------------------
 1 file changed, 38 insertions(+), 39 deletions(-)

diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 8e435da730996..cfb64e5a7d45d 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -986,20 +986,12 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
  * Note that we currently allow DMA only if we get a channel
  * for both rx and tx. Otherwise we'll do PIO for both rx and tx.
  */
-static int omap2_mcspi_request_dma(struct spi_device *spi)
+static int omap2_mcspi_request_dma(struct omap2_mcspi *mcspi,
+				   struct omap2_mcspi_dma *mcspi_dma)
 {
-	struct spi_master	*master = spi->master;
-	struct omap2_mcspi	*mcspi;
-	struct omap2_mcspi_dma	*mcspi_dma;
 	int ret = 0;
 
-	mcspi = spi_master_get_devdata(master);
-	mcspi_dma = mcspi->dma_channels + spi->chip_select;
-
-	init_completion(&mcspi_dma->dma_rx_completion);
-	init_completion(&mcspi_dma->dma_tx_completion);
-
-	mcspi_dma->dma_rx = dma_request_chan(&master->dev,
+	mcspi_dma->dma_rx = dma_request_chan(mcspi->dev,
 					     mcspi_dma->dma_rx_ch_name);
 	if (IS_ERR(mcspi_dma->dma_rx)) {
 		ret = PTR_ERR(mcspi_dma->dma_rx);
@@ -1007,7 +999,7 @@ static int omap2_mcspi_request_dma(struct spi_device *spi)
 		goto no_dma;
 	}
 
-	mcspi_dma->dma_tx = dma_request_chan(&master->dev,
+	mcspi_dma->dma_tx = dma_request_chan(mcspi->dev,
 					     mcspi_dma->dma_tx_ch_name);
 	if (IS_ERR(mcspi_dma->dma_tx)) {
 		ret = PTR_ERR(mcspi_dma->dma_tx);
@@ -1016,20 +1008,40 @@ static int omap2_mcspi_request_dma(struct spi_device *spi)
 		mcspi_dma->dma_rx = NULL;
 	}
 
+	init_completion(&mcspi_dma->dma_rx_completion);
+	init_completion(&mcspi_dma->dma_tx_completion);
+
 no_dma:
 	return ret;
 }
 
+static void omap2_mcspi_release_dma(struct spi_master *master)
+{
+	struct omap2_mcspi *mcspi = spi_master_get_devdata(master);
+	struct omap2_mcspi_dma	*mcspi_dma;
+	int i;
+
+	for (i = 0; i < master->num_chipselect; i++) {
+		mcspi_dma = &mcspi->dma_channels[i];
+
+		if (mcspi_dma->dma_rx) {
+			dma_release_channel(mcspi_dma->dma_rx);
+			mcspi_dma->dma_rx = NULL;
+		}
+		if (mcspi_dma->dma_tx) {
+			dma_release_channel(mcspi_dma->dma_tx);
+			mcspi_dma->dma_tx = NULL;
+		}
+	}
+}
+
 static int omap2_mcspi_setup(struct spi_device *spi)
 {
 	int			ret;
 	struct omap2_mcspi	*mcspi = spi_master_get_devdata(spi->master);
 	struct omap2_mcspi_regs	*ctx = &mcspi->ctx;
-	struct omap2_mcspi_dma	*mcspi_dma;
 	struct omap2_mcspi_cs	*cs = spi->controller_state;
 
-	mcspi_dma = &mcspi->dma_channels[spi->chip_select];
-
 	if (!cs) {
 		cs = kzalloc(sizeof *cs, GFP_KERNEL);
 		if (!cs)
@@ -1054,13 +1066,6 @@ static int omap2_mcspi_setup(struct spi_device *spi)
 		}
 	}
 
-	if (!mcspi_dma->dma_rx || !mcspi_dma->dma_tx) {
-		ret = omap2_mcspi_request_dma(spi);
-		if (ret)
-			dev_warn(&spi->dev, "not using DMA for McSPI (%d)\n",
-				 ret);
-	}
-
 	ret = pm_runtime_get_sync(mcspi->dev);
 	if (ret < 0) {
 		pm_runtime_put_noidle(mcspi->dev);
@@ -1077,12 +1082,8 @@ static int omap2_mcspi_setup(struct spi_device *spi)
 
 static void omap2_mcspi_cleanup(struct spi_device *spi)
 {
-	struct omap2_mcspi	*mcspi;
-	struct omap2_mcspi_dma	*mcspi_dma;
 	struct omap2_mcspi_cs	*cs;
 
-	mcspi = spi_master_get_devdata(spi->master);
-
 	if (spi->controller_state) {
 		/* Unlink controller state from context save list */
 		cs = spi->controller_state;
@@ -1091,19 +1092,6 @@ static void omap2_mcspi_cleanup(struct spi_device *spi)
 		kfree(cs);
 	}
 
-	if (spi->chip_select < spi->master->num_chipselect) {
-		mcspi_dma = &mcspi->dma_channels[spi->chip_select];
-
-		if (mcspi_dma->dma_rx) {
-			dma_release_channel(mcspi_dma->dma_rx);
-			mcspi_dma->dma_rx = NULL;
-		}
-		if (mcspi_dma->dma_tx) {
-			dma_release_channel(mcspi_dma->dma_tx);
-			mcspi_dma->dma_tx = NULL;
-		}
-	}
-
 	if (gpio_is_valid(spi->cs_gpio))
 		gpio_free(spi->cs_gpio);
 }
@@ -1314,6 +1302,9 @@ static bool omap2_mcspi_can_dma(struct spi_master *master,
 	if (spi_controller_is_slave(master))
 		return true;
 
+	master->dma_rx = mcspi_dma->dma_rx;
+	master->dma_tx = mcspi_dma->dma_tx;
+
 	return (xfer->len >= DMA_MIN_BYTES);
 }
 
@@ -1501,6 +1492,11 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 	for (i = 0; i < master->num_chipselect; i++) {
 		sprintf(mcspi->dma_channels[i].dma_rx_ch_name, "rx%d", i);
 		sprintf(mcspi->dma_channels[i].dma_tx_ch_name, "tx%d", i);
+
+		status = omap2_mcspi_request_dma(mcspi,
+						 &mcspi->dma_channels[i]);
+		if (status == -EPROBE_DEFER)
+			goto free_master;
 	}
 
 	status = platform_get_irq(pdev, 0);
@@ -1538,6 +1534,7 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 free_master:
+	omap2_mcspi_release_dma(master);
 	spi_master_put(master);
 	return status;
 }
@@ -1547,6 +1544,8 @@ static int omap2_mcspi_remove(struct platform_device *pdev)
 	struct spi_master *master = platform_get_drvdata(pdev);
 	struct omap2_mcspi *mcspi = spi_master_get_devdata(master);
 
+	omap2_mcspi_release_dma(master);
+
 	pm_runtime_dont_use_autosuspend(mcspi->dev);
 	pm_runtime_put_sync(mcspi->dev);
 	pm_runtime_disable(&pdev->dev);
-- 
2.20.1

[PATCH AUTOSEL 5.4 03/35] drm/mediatek: Find the cursor plane instead of hard coding it

[Sasha Levin]

From: Evan Benn <evanbenn@chromium.org>

[ Upstream commit 318caac7c81cdf5806df30c3d72385659a5f0f53 ]

The cursor and primary planes were hard coded.
Now search for them for passing to drm_crtc_init_with_planes

Signed-off-by: Evan Benn <evanbenn@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/mediatek/mtk_drm_crtc.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_drm_crtc.c b/drivers/gpu/drm/mediatek/mtk_drm_crtc.c
index e6c049f4f08bb..f9455f2724d23 100644
--- a/drivers/gpu/drm/mediatek/mtk_drm_crtc.c
+++ b/drivers/gpu/drm/mediatek/mtk_drm_crtc.c
@@ -496,10 +496,18 @@ static const struct drm_crtc_helper_funcs mtk_crtc_helper_funcs = {
 
 static int mtk_drm_crtc_init(struct drm_device *drm,
 			     struct mtk_drm_crtc *mtk_crtc,
-			     struct drm_plane *primary,
-			     struct drm_plane *cursor, unsigned int pipe)
+			     unsigned int pipe)
 {
-	int ret;
+	struct drm_plane *primary = NULL;
+	struct drm_plane *cursor = NULL;
+	int i, ret;
+
+	for (i = 0; i < mtk_crtc->layer_nr; i++) {
+		if (mtk_crtc->planes[i].type == DRM_PLANE_TYPE_PRIMARY)
+			primary = &mtk_crtc->planes[i];
+		else if (mtk_crtc->planes[i].type == DRM_PLANE_TYPE_CURSOR)
+			cursor = &mtk_crtc->planes[i];
+	}
 
 	ret = drm_crtc_init_with_planes(drm, &mtk_crtc->base, primary, cursor,
 					&mtk_crtc_funcs, NULL);
@@ -608,9 +616,7 @@ int mtk_drm_crtc_create(struct drm_device *drm_dev,
 			return ret;
 	}
 
-	ret = mtk_drm_crtc_init(drm_dev, mtk_crtc, &mtk_crtc->planes[0],
-				mtk_crtc->layer_nr > 1 ? &mtk_crtc->planes[1] :
-				NULL, pipe);
+	ret = mtk_drm_crtc_init(drm_dev, mtk_crtc, pipe);
 	if (ret < 0)
 		return ret;
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 04/35] ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties

[Sasha Levin]

From: Johan Hovold <johan@kernel.org>

[ Upstream commit bcbf53a0dab50980867476994f6079c1ec5bb3a3 ]

The sram-node compatible properties have mistakingly combined the
model-specific string with the generic "mtd-ram" string.

Note that neither "cy7c1019dv33-10zsxi, mtd-ram" or
"cy7c1019dv33-10zsxi" are used by any in-kernel driver and they are
not present in any binding.

The physmap driver will however bind to platform devices that specify
"mtd-ram".

Fixes: fc48e76489fd ("ARM: dts: imx6: Add support for Toradex Colibri iMX6 module")
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 9a5d6c94cca4d..40d750fccf6d6 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -236,7 +236,7 @@
 
 	/* SRAM on Colibri nEXT_CS0 */
 	sram@0,0 {
-		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
+		compatible = "cypress,cy7c1019dv33-10zsxi", "mtd-ram";
 		reg = <0 0 0x00010000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -247,7 +247,7 @@
 
 	/* SRAM on Colibri nEXT_CS1 */
 	sram@1,0 {
-		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
+		compatible = "cypress,cy7c1019dv33-10zsxi", "mtd-ram";
 		reg = <1 0 0x00010000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-- 
2.20.1

[PATCH AUTOSEL 5.4 05/35] phy: ti: gmii-sel: fix set of copy-paste errors

[Sasha Levin]

From: Grygorii Strashko <grygorii.strashko@ti.com>

[ Upstream commit eefed634eb61e4094b9fb8183cb8d43b26838517 ]

- under PHY_INTERFACE_MODE_MII the 'mode' func parameter is assigned
instead of 'gmii_sel_mode' and it's working only because the default value
'gmii_sel_mode' is set to 0.

- console outputs use 'rgmii_id' and 'mode' values to print PHY mode
instead of using 'submode' value which is representing PHY interface mode
now.

This patch fixes above two cases.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/ti/phy-gmii-sel.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/phy/ti/phy-gmii-sel.c b/drivers/phy/ti/phy-gmii-sel.c
index a28bd15297f53..e998e9cd8d1f8 100644
--- a/drivers/phy/ti/phy-gmii-sel.c
+++ b/drivers/phy/ti/phy-gmii-sel.c
@@ -80,20 +80,19 @@ static int phy_gmii_sel_mode(struct phy *phy, enum phy_mode mode, int submode)
 		break;
 
 	case PHY_INTERFACE_MODE_MII:
-		mode = AM33XX_GMII_SEL_MODE_MII;
+		gmii_sel_mode = AM33XX_GMII_SEL_MODE_MII;
 		break;
 
 	default:
-		dev_warn(dev,
-			 "port%u: unsupported mode: \"%s\". Defaulting to MII.\n",
-			 if_phy->id, phy_modes(rgmii_id));
+		dev_warn(dev, "port%u: unsupported mode: \"%s\"\n",
+			 if_phy->id, phy_modes(submode));
 		return -EINVAL;
 	}
 
 	if_phy->phy_if_mode = submode;
 
 	dev_dbg(dev, "%s id:%u mode:%u rgmii_id:%d rmii_clk_ext:%d\n",
-		__func__, if_phy->id, mode, rgmii_id,
+		__func__, if_phy->id, submode, rgmii_id,
 		if_phy->rmii_clock_external);
 
 	regfield = if_phy->fields[PHY_GMII_SEL_PORT_MODE];
-- 
2.20.1

[PATCH AUTOSEL 5.4 06/35] phy: ti: gmii-sel: do not fail in case of gmii

[Sasha Levin]

From: Grygorii Strashko <grygorii.strashko@ti.com>

[ Upstream commit 58aa7729310db04ffcc022c98002dd8fcb486c58 ]

The "gmii" PHY interface mode is supported on TI AM335x/437x/5xx SoCs, so
don't fail if it's selected.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/ti/phy-gmii-sel.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/phy/ti/phy-gmii-sel.c b/drivers/phy/ti/phy-gmii-sel.c
index e998e9cd8d1f8..1c536fc03c83c 100644
--- a/drivers/phy/ti/phy-gmii-sel.c
+++ b/drivers/phy/ti/phy-gmii-sel.c
@@ -80,6 +80,7 @@ static int phy_gmii_sel_mode(struct phy *phy, enum phy_mode mode, int submode)
 		break;
 
 	case PHY_INTERFACE_MODE_MII:
+	case PHY_INTERFACE_MODE_GMII:
 		gmii_sel_mode = AM33XX_GMII_SEL_MODE_MII;
 		break;
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 07/35] ARM: dts: dra7-l4: mark timer13-16 as pwm capable

[Sasha Levin]

From: Grygorii Strashko <grygorii.strashko@ti.com>

[ Upstream commit 00a39c92c8ab94727f021297d1748531af113fcd ]

DMTimers 13 - 16 are PWM capable and also can be used for CPTS input
signals generation. Hence, mark them as "ti,timer-pwm".

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/dra7-l4.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi
index c3954e34835b8..3ae4f6358da41 100644
--- a/arch/arm/boot/dts/dra7-l4.dtsi
+++ b/arch/arm/boot/dts/dra7-l4.dtsi
@@ -3413,6 +3413,7 @@
 				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER13_CLKCTRL 24>;
 				clock-names = "fck";
 				interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
@@ -3441,6 +3442,7 @@
 				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER14_CLKCTRL 24>;
 				clock-names = "fck";
 				interrupts = <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
@@ -3469,6 +3471,7 @@
 				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>;
 				clock-names = "fck";
 				interrupts = <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
@@ -3497,6 +3500,7 @@
 				clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>;
 				clock-names = "fck";
 				interrupts = <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>;
+				ti,timer-pwm;
 			};
 		};
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 08/35] ASoC: meson: g12a: add tohdmitx reset

[Sasha Levin]

From: Jerome Brunet <jbrunet@baylibre.com>

[ Upstream commit 22946f37557e27697aabc8e4f62642bfe4a17fd8 ]

Reset the g12a hdmi codec glue on probe. This ensure a sane startup state.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200221121146.1498427-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/meson/g12a-tohdmitx.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/sound/soc/meson/g12a-tohdmitx.c b/sound/soc/meson/g12a-tohdmitx.c
index 9cfbd343a00c8..8a0db28a6a406 100644
--- a/sound/soc/meson/g12a-tohdmitx.c
+++ b/sound/soc/meson/g12a-tohdmitx.c
@@ -8,6 +8,7 @@
 #include <linux/module.h>
 #include <sound/pcm_params.h>
 #include <linux/regmap.h>
+#include <linux/reset.h>
 #include <sound/soc.h>
 #include <sound/soc-dai.h>
 
@@ -378,6 +379,11 @@ static int g12a_tohdmitx_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	void __iomem *regs;
 	struct regmap *map;
+	int ret;
+
+	ret = device_reset(dev);
+	if (ret)
+		return ret;
 
 	regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(regs))
-- 
2.20.1

Re: [PATCH AUTOSEL 5.4 08/35] ASoC: meson: g12a: add tohdmitx reset

[Jerome Brunet]

On Mon 16 Mar 2020 at 03:33, Sasha Levin <sashal@kernel.org> wrote:

> From: Jerome Brunet <jbrunet@baylibre.com>
>
> [ Upstream commit 22946f37557e27697aabc8e4f62642bfe4a17fd8 ]
>
> Reset the g12a hdmi codec glue on probe. This ensure a sane startup state.
>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
> Link: https://lore.kernel.org/r/20200221121146.1498427-1-jbrunet@baylibre.com
> Signed-off-by: Mark Brown <broonie@kernel.org>
> Signed-off-by: Sasha Levin <sashal@kernel.org>

Hi Sasha,

The tohdmitx reset property is not in the amlogic g12a DT in v5.4.
Backporting this patch on v5.4 would break the hdmi sound, and probably
the related sound card since the reset is not optional.

Could you please drop this from v5.4 stable ?
It is ok to keep it for v5.5.

Thanks
Jerome

> ---
>  sound/soc/meson/g12a-tohdmitx.c | 6 ++++++
>  1 file changed, 6 insertions(+)
>
> diff --git a/sound/soc/meson/g12a-tohdmitx.c b/sound/soc/meson/g12a-tohdmitx.c
> index 9cfbd343a00c8..8a0db28a6a406 100644
> --- a/sound/soc/meson/g12a-tohdmitx.c
> +++ b/sound/soc/meson/g12a-tohdmitx.c
> @@ -8,6 +8,7 @@
>  #include <linux/module.h>
>  #include <sound/pcm_params.h>
>  #include <linux/regmap.h>
> +#include <linux/reset.h>
>  #include <sound/soc.h>
>  #include <sound/soc-dai.h>
>  
> @@ -378,6 +379,11 @@ static int g12a_tohdmitx_probe(struct platform_device *pdev)
>  	struct device *dev = &pdev->dev;
>  	void __iomem *regs;
>  	struct regmap *map;
> +	int ret;
> +
> +	ret = device_reset(dev);
> +	if (ret)
> +		return ret;
>  
>  	regs = devm_platform_ioremap_resource(pdev, 0);
>  	if (IS_ERR(regs))

Re: [PATCH AUTOSEL 5.4 08/35] ASoC: meson: g12a: add tohdmitx reset

[Jerome Brunet]

On Mon 16 Mar 2020 at 09:28, Jerome Brunet <jbrunet@baylibre.com> wrote:

> On Mon 16 Mar 2020 at 03:33, Sasha Levin <sashal@kernel.org> wrote:
>
>> From: Jerome Brunet <jbrunet@baylibre.com>
>>
>> [ Upstream commit 22946f37557e27697aabc8e4f62642bfe4a17fd8 ]
>>
>> Reset the g12a hdmi codec glue on probe. This ensure a sane startup state.
>>
>> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
>> Link: https://lore.kernel.org/r/20200221121146.1498427-1-jbrunet@baylibre.com
>> Signed-off-by: Mark Brown <broonie@kernel.org>
>> Signed-off-by: Sasha Levin <sashal@kernel.org>
>
> Hi Sasha,
>
> The tohdmitx reset property is not in the amlogic g12a DT in v5.4.
> Backporting this patch on v5.4 would break the hdmi sound, and probably
> the related sound card since the reset is not optional.
>
> Could you please drop this from v5.4 stable ?

Hi Sasha,

I just received a notification that this patch has been applied to 5.4
stable.

As explained above, it will cause a regression.
Could you please drop it from v5.4 stable ?

Thanks
Jerome

> It is ok to keep it for v5.5.
>
> Thanks
> Jerome
>
>> ---
>>  sound/soc/meson/g12a-tohdmitx.c | 6 ++++++
>>  1 file changed, 6 insertions(+)
>>
>> diff --git a/sound/soc/meson/g12a-tohdmitx.c b/sound/soc/meson/g12a-tohdmitx.c
>> index 9cfbd343a00c8..8a0db28a6a406 100644
>> --- a/sound/soc/meson/g12a-tohdmitx.c
>> +++ b/sound/soc/meson/g12a-tohdmitx.c
>> @@ -8,6 +8,7 @@
>>  #include <linux/module.h>
>>  #include <sound/pcm_params.h>
>>  #include <linux/regmap.h>
>> +#include <linux/reset.h>
>>  #include <sound/soc.h>
>>  #include <sound/soc-dai.h>
>>  
>> @@ -378,6 +379,11 @@ static int g12a_tohdmitx_probe(struct platform_device *pdev)
>>  	struct device *dev = &pdev->dev;
>>  	void __iomem *regs;
>>  	struct regmap *map;
>> +	int ret;
>> +
>> +	ret = device_reset(dev);
>> +	if (ret)
>> +		return ret;
>>  
>>  	regs = devm_platform_ioremap_resource(pdev, 0);
>>  	if (IS_ERR(regs))

Re: [PATCH AUTOSEL 5.4 08/35] ASoC: meson: g12a: add tohdmitx reset

[Sasha Levin]

On Sun, Mar 22, 2020 at 07:31:31PM +0100, Jerome Brunet wrote:
>
>On Mon 16 Mar 2020 at 09:28, Jerome Brunet <jbrunet@baylibre.com> wrote:
>
>> On Mon 16 Mar 2020 at 03:33, Sasha Levin <sashal@kernel.org> wrote:
>>
>>> From: Jerome Brunet <jbrunet@baylibre.com>
>>>
>>> [ Upstream commit 22946f37557e27697aabc8e4f62642bfe4a17fd8 ]
>>>
>>> Reset the g12a hdmi codec glue on probe. This ensure a sane startup state.
>>>
>>> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
>>> Link: https://lore.kernel.org/r/20200221121146.1498427-1-jbrunet@baylibre.com
>>> Signed-off-by: Mark Brown <broonie@kernel.org>
>>> Signed-off-by: Sasha Levin <sashal@kernel.org>
>>
>> Hi Sasha,
>>
>> The tohdmitx reset property is not in the amlogic g12a DT in v5.4.
>> Backporting this patch on v5.4 would break the hdmi sound, and probably
>> the related sound card since the reset is not optional.
>>
>> Could you please drop this from v5.4 stable ?
>
>Hi Sasha,
>
>I just received a notification that this patch has been applied to 5.4
>stable.
>
>As explained above, it will cause a regression.
>Could you please drop it from v5.4 stable ?

Hi Jerome,

Sorry - I've missed your previous mail. Now dropped from all trees.

-- 
Thanks,
Sasha

[PATCH AUTOSEL 5.4 09/35] spi: qup: call spi_qup_pm_resume_runtime before suspending

[Sasha Levin]

From: Yuji Sasaki <sasakiy@chromium.org>

[ Upstream commit 136b5cd2e2f97581ae560cff0db2a3b5369112da ]

spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().

Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-qup.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index 2f559e5311002..fa8079fbea77a 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -1217,6 +1217,11 @@ static int spi_qup_suspend(struct device *device)
 	struct spi_qup *controller = spi_master_get_devdata(master);
 	int ret;
 
+	if (pm_runtime_suspended(device)) {
+		ret = spi_qup_pm_resume_runtime(device);
+		if (ret)
+			return ret;
+	}
 	ret = spi_master_suspend(master);
 	if (ret)
 		return ret;
@@ -1225,10 +1230,8 @@ static int spi_qup_suspend(struct device *device)
 	if (ret)
 		return ret;
 
-	if (!pm_runtime_suspended(device)) {
-		clk_disable_unprepare(controller->cclk);
-		clk_disable_unprepare(controller->iclk);
-	}
+	clk_disable_unprepare(controller->cclk);
+	clk_disable_unprepare(controller->iclk);
 	return 0;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 10/35] powerpc: Include .BTF section

[Sasha Levin]

From: "Naveen N. Rao" <naveen.n.rao@linux.vnet.ibm.com>

[ Upstream commit cb0cc635c7a9fa8a3a0f75d4d896721819c63add ]

Selecting CONFIG_DEBUG_INFO_BTF results in the below warning from ld:
  ld: warning: orphan section `.BTF' from `.btf.vmlinux.bin.o' being placed in section `.BTF'

Include .BTF section in vmlinux explicitly to fix the same.

Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220113132.857132-1-naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/powerpc/kernel/vmlinux.lds.S | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S
index 060a1acd7c6d7..4638d28633888 100644
--- a/arch/powerpc/kernel/vmlinux.lds.S
+++ b/arch/powerpc/kernel/vmlinux.lds.S
@@ -326,6 +326,12 @@ SECTIONS
 		*(.branch_lt)
 	}
 
+#ifdef CONFIG_DEBUG_INFO_BTF
+	.BTF : AT(ADDR(.BTF) - LOAD_OFFSET) {
+		*(.BTF)
+	}
+#endif
+
 	.opd : AT(ADDR(.opd) - LOAD_OFFSET) {
 		__start_opd = .;
 		KEEP(*(.opd))
-- 
2.20.1

[PATCH AUTOSEL 5.4 11/35] cifs: fix potential mismatch of UNC paths

[Sasha Levin]

From: "Paulo Alcantara (SUSE)" <pc@cjr.nz>

[ Upstream commit 154255233830e1e4dd0d99ac929a5dce588c0b81 ]

Ensure that full_path is an UNC path that contains '\\' as delimiter,
which is required by cifs_build_devname().

The build_path_from_dentry_optional_prefix() function may return a
path with '/' as delimiter when using SMB1 UNIX extensions, for
example.

Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/cifs/cifs_dfs_ref.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/fs/cifs/cifs_dfs_ref.c b/fs/cifs/cifs_dfs_ref.c
index 606f26d862dc1..cc3ada12848d9 100644
--- a/fs/cifs/cifs_dfs_ref.c
+++ b/fs/cifs/cifs_dfs_ref.c
@@ -324,6 +324,8 @@ static struct vfsmount *cifs_dfs_do_automount(struct dentry *mntpt)
 	if (full_path == NULL)
 		goto cdda_exit;
 
+	convert_delimiter(full_path, '\\');
+
 	cifs_dbg(FYI, "%s: full_path: %s\n", __func__, full_path);
 
 	if (!cifs_sb_master_tlink(cifs_sb)) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 12/35] cifs: add missing mount option to /proc/mounts

[Sasha Levin]

From: Steve French <stfrench@microsoft.com>

[ Upstream commit ec57010acd03428a749d2600bf09bd537eaae993 ]

We were not displaying the mount option "signloosely" in /proc/mounts
for cifs mounts which some users found confusing recently

Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/cifs/cifsfs.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/fs/cifs/cifsfs.c b/fs/cifs/cifsfs.c
index 637624ab6e464..115f063497ffa 100644
--- a/fs/cifs/cifsfs.c
+++ b/fs/cifs/cifsfs.c
@@ -530,6 +530,8 @@ cifs_show_options(struct seq_file *s, struct dentry *root)
 
 	if (tcon->seal)
 		seq_puts(s, ",seal");
+	else if (tcon->ses->server->ignore_signature)
+		seq_puts(s, ",signloosely");
 	if (tcon->nocase)
 		seq_puts(s, ",nocase");
 	if (tcon->local_lease)
-- 
2.20.1

[PATCH AUTOSEL 5.4 13/35] ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes

[Sasha Levin]

From: Kishon Vijay Abraham I <kishon@ti.com>

[ Upstream commit 27f13774654ea6bd0b6fc9b97cce8d19e5735661 ]

'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/dra7.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 953f0ffce2a90..6481d2b7d6b6f 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -184,6 +184,7 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
+				dma-ranges = <0x02000000 0x0 0x00000000 0x00000000 0x1 0x00000000>;
 				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
@@ -238,6 +239,7 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x30013000 0x13000 0 0xffed000>;
+				dma-ranges = <0x02000000 0x0 0x00000000 0x00000000 0x1 0x00000000>;
 				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
-- 
2.20.1

[PATCH AUTOSEL 5.4 14/35] spi: pxa2xx: Add CS control clock quirk

[Sasha Levin]

From: Evan Green <evgreen@chromium.org>

[ Upstream commit 683f65ded66a9a7ff01ed7280804d2132ebfdf7e ]

In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.

Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.

Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-pxa2xx.c | 23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c
index 2fd843b18297d..7231456732068 100644
--- a/drivers/spi/spi-pxa2xx.c
+++ b/drivers/spi/spi-pxa2xx.c
@@ -68,6 +68,10 @@ MODULE_ALIAS("platform:pxa2xx-spi");
 #define LPSS_CAPS_CS_EN_SHIFT			9
 #define LPSS_CAPS_CS_EN_MASK			(0xf << LPSS_CAPS_CS_EN_SHIFT)
 
+#define LPSS_PRIV_CLOCK_GATE 0x38
+#define LPSS_PRIV_CLOCK_GATE_CLK_CTL_MASK 0x3
+#define LPSS_PRIV_CLOCK_GATE_CLK_CTL_FORCE_ON 0x3
+
 struct lpss_config {
 	/* LPSS offset from drv_data->ioaddr */
 	unsigned offset;
@@ -84,6 +88,8 @@ struct lpss_config {
 	unsigned cs_sel_shift;
 	unsigned cs_sel_mask;
 	unsigned cs_num;
+	/* Quirks */
+	unsigned cs_clk_stays_gated : 1;
 };
 
 /* Keep these sorted with enum pxa_ssp_type */
@@ -154,6 +160,7 @@ static const struct lpss_config lpss_platforms[] = {
 		.tx_threshold_hi = 56,
 		.cs_sel_shift = 8,
 		.cs_sel_mask = 3 << 8,
+		.cs_clk_stays_gated = true,
 	},
 };
 
@@ -381,6 +388,22 @@ static void lpss_ssp_cs_control(struct spi_device *spi, bool enable)
 	else
 		value |= LPSS_CS_CONTROL_CS_HIGH;
 	__lpss_ssp_write_priv(drv_data, config->reg_cs_ctrl, value);
+	if (config->cs_clk_stays_gated) {
+		u32 clkgate;
+
+		/*
+		 * Changing CS alone when dynamic clock gating is on won't
+		 * actually flip CS at that time. This ruins SPI transfers
+		 * that specify delays, or have no data. Toggle the clock mode
+		 * to force on briefly to poke the CS pin to move.
+		 */
+		clkgate = __lpss_ssp_read_priv(drv_data, LPSS_PRIV_CLOCK_GATE);
+		value = (clkgate & ~LPSS_PRIV_CLOCK_GATE_CLK_CTL_MASK) |
+			LPSS_PRIV_CLOCK_GATE_CLK_CTL_FORCE_ON;
+
+		__lpss_ssp_write_priv(drv_data, LPSS_PRIV_CLOCK_GATE, value);
+		__lpss_ssp_write_priv(drv_data, LPSS_PRIV_CLOCK_GATE, clkgate);
+	}
 }
 
 static void cs_assert(struct spi_device *spi)
-- 
2.20.1

[PATCH AUTOSEL 5.4 15/35] spi/zynqmp: remove entry that causes a cs glitch

[Sasha Levin]

From: Thommy Jakobsson <thommyj@gmail.com>

[ Upstream commit 5dd8304981ecffa77bb72b1c57c4be5dfe6cfae9 ]

In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.

This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.

The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.

It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.

Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-zynqmp-gqspi.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
index 60c4de4e44856..7412a3042a8d2 100644
--- a/drivers/spi/spi-zynqmp-gqspi.c
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -401,9 +401,6 @@ static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high)
 
 	zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, genfifoentry);
 
-	/* Dummy generic FIFO entry */
-	zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, 0x0);
-
 	/* Manually start the generic FIFO command */
 	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
 			zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST) |
-- 
2.20.1

[PATCH AUTOSEL 5.4 16/35] drm/exynos: dsi: propagate error value and silence meaningless warning

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 0a9d1e3f3f038785ebc72d53f1c409d07f6b4ff5 ]

Properly propagate error value from devm_regulator_bulk_get() and don't
confuse user with meaningless warning about failure in getting regulators
in case of deferred probe.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/exynos/exynos_drm_dsi.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index 6926cee91b367..2767408c4750e 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -1750,8 +1750,9 @@ static int exynos_dsi_probe(struct platform_device *pdev)
 	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(dsi->supplies),
 				      dsi->supplies);
 	if (ret) {
-		dev_info(dev, "failed to get regulators: %d\n", ret);
-		return -EPROBE_DEFER;
+		if (ret != -EPROBE_DEFER)
+			dev_info(dev, "failed to get regulators: %d\n", ret);
+		return ret;
 	}
 
 	dsi->clks = devm_kcalloc(dev,
-- 
2.20.1

[PATCH AUTOSEL 5.4 17/35] drm/exynos: dsi: fix workaround for the legacy clock name

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit c0fd99d659ba5582e09625c7a985d63fc2ca74b5 ]

Writing to the built-in strings arrays doesn't work if driver is loaded
as kernel module. This is also considered as a bad pattern. Fix this by
adding a call to clk_get() with legacy clock name. This fixes following
kernel oops if driver is loaded as module:

Unable to handle kernel paging request at virtual address bf047978
 pgd = (ptrval)
 [bf047978] *pgd=59344811, *pte=5903c6df, *ppte=5903c65f
 Internal error: Oops: 80f [#1] SMP ARM
 Modules linked in: mc exynosdrm(+) analogix_dp rtc_s3c exynos_ppmu i2c_gpio
 CPU: 1 PID: 212 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219 #326
 videodev: Linux video capture interface: v2.00
 Hardware name: Samsung Exynos (Flattened Device Tree)
 PC is at exynos_dsi_probe+0x1f0/0x384 [exynosdrm]
 LR is at exynos_dsi_probe+0x1dc/0x384 [exynosdrm]
 ...
 Process systemd-udevd (pid: 212, stack limit = 0x(ptrval))
 ...
 [<bf03cf14>] (exynos_dsi_probe [exynosdrm]) from [<c09b1ca0>] (platform_drv_probe+0x6c/0xa4)
 [<c09b1ca0>] (platform_drv_probe) from [<c09afcb8>] (really_probe+0x210/0x350)
 [<c09afcb8>] (really_probe) from [<c09aff74>] (driver_probe_device+0x60/0x1a0)
 [<c09aff74>] (driver_probe_device) from [<c09b0254>] (device_driver_attach+0x58/0x60)
 [<c09b0254>] (device_driver_attach) from [<c09b02dc>] (__driver_attach+0x80/0xbc)
 [<c09b02dc>] (__driver_attach) from [<c09ade00>] (bus_for_each_dev+0x68/0xb4)
 [<c09ade00>] (bus_for_each_dev) from [<c09aefd8>] (bus_add_driver+0x130/0x1e8)
 [<c09aefd8>] (bus_add_driver) from [<c09b0d64>] (driver_register+0x78/0x110)
 [<c09b0d64>] (driver_register) from [<bf038558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
 [<bf038558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
 [<c0302fa8>] (do_one_initcall) from [<c03dd02c>] (do_init_module+0x60/0x210)
 [<c03dd02c>] (do_init_module) from [<c03dbf44>] (load_module+0x1c0c/0x2310)
 [<c03dbf44>] (load_module) from [<c03dc85c>] (sys_finit_module+0xac/0xbc)
 [<c03dc85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
 Exception stack(0xd979bfa8 to 0xd979bff0)
 ...
 ---[ end trace db16efe05faab470 ]---

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/exynos/exynos_drm_dsi.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index 2767408c4750e..8ed94c9948008 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -1765,9 +1765,10 @@ static int exynos_dsi_probe(struct platform_device *pdev)
 		dsi->clks[i] = devm_clk_get(dev, clk_names[i]);
 		if (IS_ERR(dsi->clks[i])) {
 			if (strcmp(clk_names[i], "sclk_mipi") == 0) {
-				strcpy(clk_names[i], OLD_SCLK_MIPI_CLK_NAME);
-				i--;
-				continue;
+				dsi->clks[i] = devm_clk_get(dev,
+							OLD_SCLK_MIPI_CLK_NAME);
+				if (!IS_ERR(dsi->clks[i]))
+					continue;
 			}
 
 			dev_info(dev, "failed to get the clock: %s\n",
-- 
2.20.1

[PATCH AUTOSEL 5.4 18/35] drm/exynos: hdmi: don't leak enable HDMI_EN regulator if probe fails

[Sasha Levin]

From: Marek Szyprowski <m.szyprowski@samsung.com>

[ Upstream commit 3b6a9b19ab652efac7ad4c392add6f1235019568 ]

Move enabling and disabling HDMI_EN optional regulator to probe() function
to keep track on the regulator status. This fixes following warning if
probe() fails (for example when I2C DDC adapter cannot be yet gathered
due to the missing driver). This fixes following warning observed on
Arndale5250 board with multi_v7_defconfig:

[drm] Failed to get ddc i2c adapter by node
------------[ cut here ]------------
WARNING: CPU: 0 PID: 214 at drivers/regulator/core.c:2051 _regulator_put+0x16c/0x184
Modules linked in: ...
CPU: 0 PID: 214 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219-00040-g38af1dfafdbb #7570
Hardware name: Samsung Exynos (Flattened Device Tree)
[<c0312258>] (unwind_backtrace) from [<c030cc10>] (show_stack+0x10/0x14)
[<c030cc10>] (show_stack) from [<c0f0d3a0>] (dump_stack+0xcc/0xe0)
[<c0f0d3a0>] (dump_stack) from [<c0346a58>] (__warn+0xe0/0xf8)
[<c0346a58>] (__warn) from [<c0346b20>] (warn_slowpath_fmt+0xb0/0xb8)
[<c0346b20>] (warn_slowpath_fmt) from [<c0893f58>] (_regulator_put+0x16c/0x184)
[<c0893f58>] (_regulator_put) from [<c0893f8c>] (regulator_put+0x1c/0x2c)
[<c0893f8c>] (regulator_put) from [<c09b2664>] (release_nodes+0x17c/0x200)
[<c09b2664>] (release_nodes) from [<c09aebe8>] (really_probe+0x10c/0x350)
[<c09aebe8>] (really_probe) from [<c09aefa8>] (driver_probe_device+0x60/0x1a0)
[<c09aefa8>] (driver_probe_device) from [<c09af288>] (device_driver_attach+0x58/0x60)
[<c09af288>] (device_driver_attach) from [<c09af310>] (__driver_attach+0x80/0xbc)
[<c09af310>] (__driver_attach) from [<c09ace34>] (bus_for_each_dev+0x68/0xb4)
[<c09ace34>] (bus_for_each_dev) from [<c09ae00c>] (bus_add_driver+0x130/0x1e8)
[<c09ae00c>] (bus_add_driver) from [<c09afd98>] (driver_register+0x78/0x110)
[<c09afd98>] (driver_register) from [<bf139558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
[<bf139558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
[<c0302fa8>] (do_one_initcall) from [<c03dc02c>] (do_init_module+0x60/0x210)
[<c03dc02c>] (do_init_module) from [<c03daf44>] (load_module+0x1c0c/0x2310)
[<c03daf44>] (load_module) from [<c03db85c>] (sys_finit_module+0xac/0xbc)
[<c03db85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xecca3fa8 to 0xecca3ff0)
...
---[ end trace 276c91214635905c ]---

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/exynos/exynos_hdmi.c | 22 ++++++++++++----------
 1 file changed, 12 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/exynos/exynos_hdmi.c b/drivers/gpu/drm/exynos/exynos_hdmi.c
index 09aa73c0f2add..0073a2b3b80a2 100644
--- a/drivers/gpu/drm/exynos/exynos_hdmi.c
+++ b/drivers/gpu/drm/exynos/exynos_hdmi.c
@@ -1802,18 +1802,10 @@ static int hdmi_resources_init(struct hdmi_context *hdata)
 
 	hdata->reg_hdmi_en = devm_regulator_get_optional(dev, "hdmi-en");
 
-	if (PTR_ERR(hdata->reg_hdmi_en) != -ENODEV) {
+	if (PTR_ERR(hdata->reg_hdmi_en) != -ENODEV)
 		if (IS_ERR(hdata->reg_hdmi_en))
 			return PTR_ERR(hdata->reg_hdmi_en);
 
-		ret = regulator_enable(hdata->reg_hdmi_en);
-		if (ret) {
-			DRM_DEV_ERROR(dev,
-				      "failed to enable hdmi-en regulator\n");
-			return ret;
-		}
-	}
-
 	return hdmi_bridge_init(hdata);
 }
 
@@ -2020,6 +2012,15 @@ static int hdmi_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (!IS_ERR(hdata->reg_hdmi_en)) {
+		ret = regulator_enable(hdata->reg_hdmi_en);
+		if (ret) {
+			DRM_DEV_ERROR(dev,
+			      "failed to enable hdmi-en regulator\n");
+			goto err_hdmiphy;
+		}
+	}
+
 	pm_runtime_enable(dev);
 
 	audio_infoframe = &hdata->audio.infoframe;
@@ -2044,7 +2045,8 @@ static int hdmi_probe(struct platform_device *pdev)
 
 err_rpm_disable:
 	pm_runtime_disable(dev);
-
+	if (!IS_ERR(hdata->reg_hdmi_en))
+		regulator_disable(hdata->reg_hdmi_en);
 err_hdmiphy:
 	if (hdata->hdmiphy_port)
 		put_device(&hdata->hdmiphy_port->dev);
-- 
2.20.1

[PATCH AUTOSEL 5.4 19/35] drivers/perf: fsl_imx8_ddr: Correct the CLEAR bit definition

[Sasha Levin]

From: Joakim Zhang <qiangqing.zhang@nxp.com>

[ Upstream commit 049d919168458ac54e7fad27cd156a958b042d2f ]

When disabling a counter from ddr_perf_event_stop(), the counter value
is reset to 0 at the same time.

Preserve the counter value by performing a read-modify-write of the
PMU register and clearing only the enable bit.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/perf/fsl_imx8_ddr_perf.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/perf/fsl_imx8_ddr_perf.c b/drivers/perf/fsl_imx8_ddr_perf.c
index 0e51baa48b149..6eef47de8fccc 100644
--- a/drivers/perf/fsl_imx8_ddr_perf.c
+++ b/drivers/perf/fsl_imx8_ddr_perf.c
@@ -327,9 +327,10 @@ static void ddr_perf_counter_enable(struct ddr_pmu *pmu, int config,
 
 	if (enable) {
 		/*
-		 * must disable first, then enable again
-		 * otherwise, cycle counter will not work
-		 * if previous state is enabled.
+		 * cycle counter is special which should firstly write 0 then
+		 * write 1 into CLEAR bit to clear it. Other counters only
+		 * need write 0 into CLEAR bit and it turns out to be 1 by
+		 * hardware. Below enable flow is harmless for all counters.
 		 */
 		writel(0, pmu->base + reg);
 		val = CNTL_EN | CNTL_CLEAR;
@@ -337,7 +338,8 @@ static void ddr_perf_counter_enable(struct ddr_pmu *pmu, int config,
 		writel(val, pmu->base + reg);
 	} else {
 		/* Disable counter */
-		writel(0, pmu->base + reg);
+		val = readl_relaxed(pmu->base + reg) & CNTL_EN_MASK;
+		writel(val, pmu->base + reg);
 	}
 }
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 20/35] drivers/perf: arm_pmu_acpi: Fix incorrect checking of gicc pointer

[Sasha Levin]

From: luanshi <zhangliguang@linux.alibaba.com>

[ Upstream commit 3ba52ad55b533760a1f65836aa0ec9d35e36bb4f ]

Fix bogus NULL checks on the return value of acpi_cpu_get_madt_gicc()
by checking for a 0 'gicc->performance_interrupt' value instead.

Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/perf/arm_pmu_acpi.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/perf/arm_pmu_acpi.c b/drivers/perf/arm_pmu_acpi.c
index acce8781c456c..f5c7a845cd7bf 100644
--- a/drivers/perf/arm_pmu_acpi.c
+++ b/drivers/perf/arm_pmu_acpi.c
@@ -24,8 +24,6 @@ static int arm_pmu_acpi_register_irq(int cpu)
 	int gsi, trigger;
 
 	gicc = acpi_cpu_get_madt_gicc(cpu);
-	if (WARN_ON(!gicc))
-		return -EINVAL;
 
 	gsi = gicc->performance_interrupt;
 
@@ -64,11 +62,10 @@ static void arm_pmu_acpi_unregister_irq(int cpu)
 	int gsi;
 
 	gicc = acpi_cpu_get_madt_gicc(cpu);
-	if (!gicc)
-		return;
 
 	gsi = gicc->performance_interrupt;
-	acpi_unregister_gsi(gsi);
+	if (gsi)
+		acpi_unregister_gsi(gsi);
 }
 
 #if IS_ENABLED(CONFIG_ARM_SPE_PMU)
-- 
2.20.1

[PATCH AUTOSEL 5.4 21/35] altera-stapl: altera_get_note: prevent write beyond end of 'key'

[Sasha Levin]

From: Daniel Axtens <dja@axtens.net>

[ Upstream commit 3745488e9d599916a0b40d45d3f30e3d4720288e ]

altera_get_note is called from altera_init, where key is kzalloc(33).

When the allocation functions are annotated to allow the compiler to see
the sizes of objects, and with FORTIFY_SOURCE, we see:

In file included from drivers/misc/altera-stapl/altera.c:14:0:
In function ‘strlcpy’,
    inlined from ‘altera_init’ at drivers/misc/altera-stapl/altera.c:2189:5:
include/linux/string.h:378:4: error: call to ‘__write_overflow’ declared with attribute error: detected write beyond size of object passed as 1st parameter
    __write_overflow();
    ^~~~~~~~~~~~~~~~~~

That refers to this code in altera_get_note:

    if (key != NULL)
            strlcpy(key, &p[note_strings +
                            get_unaligned_be32(
                            &p[note_table + (8 * i)])],
                    length);

The error triggers because the length of 'key' is 33, but the copy
uses length supplied as the 'length' parameter, which is always
256. Split the size parameter into key_len and val_len, and use the
appropriate length depending on what is being copied.

Detected by compiler error, only compile-tested.

Cc: "Igor M. Liplianin" <liplianin@netup.ru>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20200120074344.504-2-dja@axtens.net
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/202002251042.D898E67AC@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/misc/altera-stapl/altera.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/misc/altera-stapl/altera.c b/drivers/misc/altera-stapl/altera.c
index 25e5f24b3fecd..5bdf574723144 100644
--- a/drivers/misc/altera-stapl/altera.c
+++ b/drivers/misc/altera-stapl/altera.c
@@ -2112,8 +2112,8 @@ static int altera_execute(struct altera_state *astate,
 	return status;
 }
 
-static int altera_get_note(u8 *p, s32 program_size,
-			s32 *offset, char *key, char *value, int length)
+static int altera_get_note(u8 *p, s32 program_size, s32 *offset,
+			   char *key, char *value, int keylen, int vallen)
 /*
  * Gets key and value of NOTE fields in the JBC file.
  * Can be called in two modes:  if offset pointer is NULL,
@@ -2170,7 +2170,7 @@ static int altera_get_note(u8 *p, s32 program_size,
 						&p[note_table + (8 * i) + 4])];
 
 				if (value != NULL)
-					strlcpy(value, value_ptr, length);
+					strlcpy(value, value_ptr, vallen);
 
 			}
 		}
@@ -2189,13 +2189,13 @@ static int altera_get_note(u8 *p, s32 program_size,
 				strlcpy(key, &p[note_strings +
 						get_unaligned_be32(
 						&p[note_table + (8 * i)])],
-					length);
+					keylen);
 
 			if (value != NULL)
 				strlcpy(value, &p[note_strings +
 						get_unaligned_be32(
 						&p[note_table + (8 * i) + 4])],
-					length);
+					vallen);
 
 			*offset = i + 1;
 		}
@@ -2449,7 +2449,7 @@ int altera_init(struct altera_config *config, const struct firmware *fw)
 			__func__, (format_version == 2) ? "Jam STAPL" :
 						"pre-standardized Jam 1.1");
 		while (altera_get_note((u8 *)fw->data, fw->size,
-					&offset, key, value, 256) == 0)
+					&offset, key, value, 32, 256) == 0)
 			printk(KERN_INFO "%s: NOTE \"%s\" = \"%s\"\n",
 					__func__, key, value);
 	}
-- 
2.20.1

[PATCH AUTOSEL 5.4 22/35] dm bio record: save/restore bi_end_io and bi_integrity

[Sasha Levin]

From: Mike Snitzer <snitzer@redhat.com>

[ Upstream commit 1b17159e52bb31f982f82a6278acd7fab1d3f67b ]

Also, save/restore __bi_remaining in case the bio was used in a
BIO_CHAIN (e.g. due to blk_queue_split).

Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/dm-bio-record.h | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/md/dm-bio-record.h b/drivers/md/dm-bio-record.h
index c82578af56a5b..2ea0360108e1d 100644
--- a/drivers/md/dm-bio-record.h
+++ b/drivers/md/dm-bio-record.h
@@ -20,8 +20,13 @@
 struct dm_bio_details {
 	struct gendisk *bi_disk;
 	u8 bi_partno;
+	int __bi_remaining;
 	unsigned long bi_flags;
 	struct bvec_iter bi_iter;
+	bio_end_io_t *bi_end_io;
+#if defined(CONFIG_BLK_DEV_INTEGRITY)
+	struct bio_integrity_payload *bi_integrity;
+#endif
 };
 
 static inline void dm_bio_record(struct dm_bio_details *bd, struct bio *bio)
@@ -30,6 +35,11 @@ static inline void dm_bio_record(struct dm_bio_details *bd, struct bio *bio)
 	bd->bi_partno = bio->bi_partno;
 	bd->bi_flags = bio->bi_flags;
 	bd->bi_iter = bio->bi_iter;
+	bd->__bi_remaining = atomic_read(&bio->__bi_remaining);
+	bd->bi_end_io = bio->bi_end_io;
+#if defined(CONFIG_BLK_DEV_INTEGRITY)
+	bd->bi_integrity = bio_integrity(bio);
+#endif
 }
 
 static inline void dm_bio_restore(struct dm_bio_details *bd, struct bio *bio)
@@ -38,6 +48,11 @@ static inline void dm_bio_restore(struct dm_bio_details *bd, struct bio *bio)
 	bio->bi_partno = bd->bi_partno;
 	bio->bi_flags = bd->bi_flags;
 	bio->bi_iter = bd->bi_iter;
+	atomic_set(&bio->__bi_remaining, bd->__bi_remaining);
+	bio->bi_end_io = bd->bi_end_io;
+#if defined(CONFIG_BLK_DEV_INTEGRITY)
+	bio->bi_integrity = bd->bi_integrity;
+#endif
 }
 
 #endif
-- 
2.20.1

[PATCH AUTOSEL 5.4 23/35] dm integrity: use dm_bio_record and dm_bio_restore

[Sasha Levin]

From: Mike Snitzer <snitzer@redhat.com>

[ Upstream commit 248aa2645aa7fc9175d1107c2593cc90d4af5a4e ]

In cases where dec_in_flight() has to requeue the integrity_bio_wait
work to transfer the rest of the data, the bio's __bi_remaining might
already have been decremented to 0, e.g.: if bio passed to underlying
data device was split via blk_queue_split().

Use dm_bio_{record,restore} rather than effectively open-coding them in
dm-integrity -- these methods now manage __bi_remaining too.

Depends-on: f7f0b057a9c1 ("dm bio record: save/restore bi_end_io and bi_integrity")
Reported-by: Daniel Glöckner <dg@emlix.com>
Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/md/dm-integrity.c | 32 +++++++++-----------------------
 1 file changed, 9 insertions(+), 23 deletions(-)

diff --git a/drivers/md/dm-integrity.c b/drivers/md/dm-integrity.c
index 57ac603f37410..145bc2e7eaf01 100644
--- a/drivers/md/dm-integrity.c
+++ b/drivers/md/dm-integrity.c
@@ -6,6 +6,8 @@
  * This file is released under the GPL.
  */
 
+#include "dm-bio-record.h"
+
 #include <linux/compiler.h>
 #include <linux/module.h>
 #include <linux/device-mapper.h>
@@ -292,11 +294,7 @@ struct dm_integrity_io {
 
 	struct completion *completion;
 
-	struct gendisk *orig_bi_disk;
-	u8 orig_bi_partno;
-	bio_end_io_t *orig_bi_end_io;
-	struct bio_integrity_payload *orig_bi_integrity;
-	struct bvec_iter orig_bi_iter;
+	struct dm_bio_details bio_details;
 };
 
 struct journal_completion {
@@ -1447,14 +1445,9 @@ static void integrity_end_io(struct bio *bio)
 {
 	struct dm_integrity_io *dio = dm_per_bio_data(bio, sizeof(struct dm_integrity_io));
 
-	bio->bi_iter = dio->orig_bi_iter;
-	bio->bi_disk = dio->orig_bi_disk;
-	bio->bi_partno = dio->orig_bi_partno;
-	if (dio->orig_bi_integrity) {
-		bio->bi_integrity = dio->orig_bi_integrity;
+	dm_bio_restore(&dio->bio_details, bio);
+	if (bio->bi_integrity)
 		bio->bi_opf |= REQ_INTEGRITY;
-	}
-	bio->bi_end_io = dio->orig_bi_end_io;
 
 	if (dio->completion)
 		complete(dio->completion);
@@ -1539,7 +1532,7 @@ static void integrity_metadata(struct work_struct *w)
 			}
 		}
 
-		__bio_for_each_segment(bv, bio, iter, dio->orig_bi_iter) {
+		__bio_for_each_segment(bv, bio, iter, dio->bio_details.bi_iter) {
 			unsigned pos;
 			char *mem, *checksums_ptr;
 
@@ -1583,7 +1576,7 @@ static void integrity_metadata(struct work_struct *w)
 		if (likely(checksums != checksums_onstack))
 			kfree(checksums);
 	} else {
-		struct bio_integrity_payload *bip = dio->orig_bi_integrity;
+		struct bio_integrity_payload *bip = dio->bio_details.bi_integrity;
 
 		if (bip) {
 			struct bio_vec biv;
@@ -2002,20 +1995,13 @@ static void dm_integrity_map_continue(struct dm_integrity_io *dio, bool from_map
 	} else
 		dio->completion = NULL;
 
-	dio->orig_bi_iter = bio->bi_iter;
-
-	dio->orig_bi_disk = bio->bi_disk;
-	dio->orig_bi_partno = bio->bi_partno;
+	dm_bio_record(&dio->bio_details, bio);
 	bio_set_dev(bio, ic->dev->bdev);
-
-	dio->orig_bi_integrity = bio_integrity(bio);
 	bio->bi_integrity = NULL;
 	bio->bi_opf &= ~REQ_INTEGRITY;
-
-	dio->orig_bi_end_io = bio->bi_end_io;
 	bio->bi_end_io = integrity_end_io;
-
 	bio->bi_iter.bi_size = dio->range.n_sectors << SECTOR_SHIFT;
+
 	generic_make_request(bio);
 
 	if (need_sync_io) {
-- 
2.20.1

[PATCH AUTOSEL 5.4 24/35] riscv: avoid the PIC offset of static percpu data in module beyond 2G limits

[Sasha Levin]

From: Vincent Chen <vincent.chen@sifive.com>

[ Upstream commit 0cff8bff7af886af0923d5c91776cd51603e531f ]

The compiler uses the PIC-relative method to access static variables
instead of GOT when the code model is PIC. Therefore, the limitation of
the access range from the instruction to the symbol address is +-2GB.
Under this circumstance, the kernel cannot load a kernel module if this
module has static per-CPU symbols declared by DEFINE_PER_CPU(). The reason
is that kernel relocates the .data..percpu section of the kernel module to
the end of kernel's .data..percpu. Hence, the distance between the per-CPU
symbols and the instruction will exceed the 2GB limits. To solve this
problem, the kernel should place the loaded module in the memory area
[&_end-2G, VMALLOC_END].

Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Suggested-by: Alexandre Ghiti <alex@ghiti.fr>
Suggested-by: Anup Patel <anup@brainfault.org>
Tested-by: Alexandre Ghiti <alex@ghiti.fr>
Tested-by: Carlos de Paula <me@carlosedp.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/riscv/kernel/module.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/riscv/kernel/module.c b/arch/riscv/kernel/module.c
index 70bb94ae61c59..6bf5b16743843 100644
--- a/arch/riscv/kernel/module.c
+++ b/arch/riscv/kernel/module.c
@@ -8,6 +8,10 @@
 #include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/moduleloader.h>
+#include <linux/vmalloc.h>
+#include <linux/sizes.h>
+#include <asm/pgtable.h>
+#include <asm/sections.h>
 
 static int apply_r_riscv_32_rela(struct module *me, u32 *location, Elf_Addr v)
 {
@@ -386,3 +390,15 @@ int apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab,
 
 	return 0;
 }
+
+#if defined(CONFIG_MMU) && defined(CONFIG_64BIT)
+#define VMALLOC_MODULE_START \
+	 max(PFN_ALIGN((unsigned long)&_end - SZ_2G), VMALLOC_START)
+void *module_alloc(unsigned long size)
+{
+	return __vmalloc_node_range(size, 1, VMALLOC_MODULE_START,
+				    VMALLOC_END, GFP_KERNEL,
+				    PAGE_KERNEL_EXEC, 0, NUMA_NO_NODE,
+				    __builtin_return_address(0));
+}
+#endif
-- 
2.20.1

[PATCH AUTOSEL 5.4 25/35] ASoC: stm32: sai: manage rebind issue

[Sasha Levin]

From: Olivier Moysan <olivier.moysan@st.com>

[ Upstream commit 0d6defc7e0e437a9fd53622f7fd85740f38d5693 ]

The commit e894efef9ac7 ("ASoC: core: add support to card rebind")
allows to rebind the sound card after a rebind of one of its component.
With this commit, the sound card is actually rebound,
but may be no more functional. The following problems have been seen
with STM32 SAI driver.

1) DMA channel is not requested:

With the sound card rebind the simplified call sequence is:
stm32_sai_sub_probe
	snd_soc_register_component
		snd_soc_try_rebind_card
			snd_soc_instantiate_card
	devm_snd_dmaengine_pcm_register

The problem occurs because the pcm must be registered,
before snd_soc_instantiate_card() is called.

Modify SAI driver, to change the call sequence as follows:
stm32_sai_sub_probe
	devm_snd_dmaengine_pcm_register
	snd_soc_register_component
		snd_soc_try_rebind_card

2) DMA channel is not released:

dma_release_channel() is not called when
devm_dmaengine_pcm_release() is executed.
This occurs because SND_DMAENGINE_PCM_DRV_NAME component,
has already been released through devm_component_release().

devm_dmaengine_pcm_release() should be called before
devm_component_release() to avoid this problem.

Call snd_dmaengine_pcm_unregister() and snd_soc_unregister_component()
explicitly from SAI driver, to have the right sequence.

Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Message-Id: <20200304102406.8093-1-olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/stm/stm32_sai_sub.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)

diff --git a/sound/soc/stm/stm32_sai_sub.c b/sound/soc/stm/stm32_sai_sub.c
index 30bcd5d3a32a8..10eb4b8e8e7ee 100644
--- a/sound/soc/stm/stm32_sai_sub.c
+++ b/sound/soc/stm/stm32_sai_sub.c
@@ -1543,20 +1543,20 @@ static int stm32_sai_sub_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	ret = devm_snd_soc_register_component(&pdev->dev, &stm32_component,
-					      &sai->cpu_dai_drv, 1);
+	ret = snd_dmaengine_pcm_register(&pdev->dev, conf, 0);
+	if (ret) {
+		dev_err(&pdev->dev, "Could not register pcm dma\n");
+		return ret;
+	}
+
+	ret = snd_soc_register_component(&pdev->dev, &stm32_component,
+					 &sai->cpu_dai_drv, 1);
 	if (ret)
 		return ret;
 
 	if (STM_SAI_PROTOCOL_IS_SPDIF(sai))
 		conf = &stm32_sai_pcm_config_spdif;
 
-	ret = devm_snd_dmaengine_pcm_register(&pdev->dev, conf, 0);
-	if (ret) {
-		dev_err(&pdev->dev, "Could not register pcm dma\n");
-		return ret;
-	}
-
 	return 0;
 }
 
@@ -1565,6 +1565,8 @@ static int stm32_sai_sub_remove(struct platform_device *pdev)
 	struct stm32_sai_sub_data *sai = dev_get_drvdata(&pdev->dev);
 
 	clk_unprepare(sai->pdata->pclk);
+	snd_dmaengine_pcm_unregister(&pdev->dev);
+	snd_soc_unregister_component(&pdev->dev);
 
 	return 0;
 }
-- 
2.20.1

[PATCH AUTOSEL 5.4 26/35] spi: spi_register_controller(): free bus id on error paths

[Sasha Levin]

From: Aaro Koskinen <aaro.koskinen@nokia.com>

[ Upstream commit f9981d4f50b475d7dbb70f3022b87a3c8bba9fd6 ]

Some error paths leave the bus id allocated. As a result the IDR
allocation will fail after a deferred probe. Fix by freeing the bus id
always on error.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Message-Id: <20200304111740.27915-1-aaro.koskinen@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi.c | 32 +++++++++++++++-----------------
 1 file changed, 15 insertions(+), 17 deletions(-)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 26b91ee0855dc..c186d3a944cd0 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -2452,7 +2452,7 @@ int spi_register_controller(struct spi_controller *ctlr)
 		if (ctlr->use_gpio_descriptors) {
 			status = spi_get_gpio_descs(ctlr);
 			if (status)
-				return status;
+				goto free_bus_id;
 			/*
 			 * A controller using GPIO descriptors always
 			 * supports SPI_CS_HIGH if need be.
@@ -2462,7 +2462,7 @@ int spi_register_controller(struct spi_controller *ctlr)
 			/* Legacy code path for GPIOs from DT */
 			status = of_spi_get_gpio_numbers(ctlr);
 			if (status)
-				return status;
+				goto free_bus_id;
 		}
 	}
 
@@ -2470,17 +2470,14 @@ int spi_register_controller(struct spi_controller *ctlr)
 	 * Even if it's just one always-selected device, there must
 	 * be at least one chipselect.
 	 */
-	if (!ctlr->num_chipselect)
-		return -EINVAL;
+	if (!ctlr->num_chipselect) {
+		status = -EINVAL;
+		goto free_bus_id;
+	}
 
 	status = device_add(&ctlr->dev);
-	if (status < 0) {
-		/* free bus id */
-		mutex_lock(&board_lock);
-		idr_remove(&spi_master_idr, ctlr->bus_num);
-		mutex_unlock(&board_lock);
-		goto done;
-	}
+	if (status < 0)
+		goto free_bus_id;
 	dev_dbg(dev, "registered %s %s\n",
 			spi_controller_is_slave(ctlr) ? "slave" : "master",
 			dev_name(&ctlr->dev));
@@ -2496,11 +2493,7 @@ int spi_register_controller(struct spi_controller *ctlr)
 		status = spi_controller_initialize_queue(ctlr);
 		if (status) {
 			device_del(&ctlr->dev);
-			/* free bus id */
-			mutex_lock(&board_lock);
-			idr_remove(&spi_master_idr, ctlr->bus_num);
-			mutex_unlock(&board_lock);
-			goto done;
+			goto free_bus_id;
 		}
 	}
 	/* add statistics */
@@ -2515,7 +2508,12 @@ int spi_register_controller(struct spi_controller *ctlr)
 	/* Register devices from the device tree and ACPI */
 	of_register_spi_devices(ctlr);
 	acpi_register_spi_devices(ctlr);
-done:
+	return status;
+
+free_bus_id:
+	mutex_lock(&board_lock);
+	idr_remove(&spi_master_idr, ctlr->bus_num);
+	mutex_unlock(&board_lock);
 	return status;
 }
 EXPORT_SYMBOL_GPL(spi_register_controller);
-- 
2.20.1

[PATCH AUTOSEL 5.4 27/35] riscv: Force flat memory model with no-mmu

[Sasha Levin]

From: Damien Le Moal <damien.lemoal@wdc.com>

[ Upstream commit aa2734202acc506d09c8e641db4da161f902df27 ]

Compilation errors trigger if ARCH_SPARSEMEM_ENABLE is enabled for
a nommu kernel. Since the sparsemem model does not make sense anyway
for the nommu case, do not allow selecting this option to always use
the flatmem model.

Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/riscv/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
index ade9699aa0dd6..a0fa4be94a68e 100644
--- a/arch/riscv/Kconfig
+++ b/arch/riscv/Kconfig
@@ -101,6 +101,7 @@ config ARCH_FLATMEM_ENABLE
 
 config ARCH_SPARSEMEM_ENABLE
 	def_bool y
+	depends on MMU
 	select SPARSEMEM_VMEMMAP_ENABLE
 
 config ARCH_SELECT_MEMORY_MODEL
-- 
2.20.1

[PATCH AUTOSEL 5.4 28/35] riscv: Fix range looking for kernel image memblock

[Sasha Levin]

From: Alexandre Ghiti <alex@ghiti.fr>

[ Upstream commit a160eed4b783d7b250a32f7e5787c9867abc5686 ]

When looking for the memblock where the kernel lives, we should check
that the memory range associated to the memblock entirely comprises the
kernel image and not only intersects with it.

Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/riscv/mm/init.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/riscv/mm/init.c b/arch/riscv/mm/init.c
index 573463d1c799a..f5d813c1304da 100644
--- a/arch/riscv/mm/init.c
+++ b/arch/riscv/mm/init.c
@@ -98,7 +98,7 @@ void __init setup_bootmem(void)
 	for_each_memblock(memory, reg) {
 		phys_addr_t end = reg->base + reg->size;
 
-		if (reg->base <= vmlinux_end && vmlinux_end <= end) {
+		if (reg->base <= vmlinux_start && vmlinux_end <= end) {
 			mem_size = min(reg->size, (phys_addr_t)-PAGE_OFFSET);
 
 			/*
-- 
2.20.1

[PATCH AUTOSEL 5.4 29/35] drm/amdgpu: clean wptr on wb when gpu recovery

[Sasha Levin]

From: Yintian Tao <yttao@amd.com>

[ Upstream commit 2ab7e274b86739f4ceed5d94b6879f2d07b2802f ]

The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.

Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c | 1 +
 drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c  | 1 +
 2 files changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c b/drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c
index 2816d03297385..14417cebe38ba 100644
--- a/drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c
+++ b/drivers/gpu/drm/amd/amdgpu/gfx_v10_0.c
@@ -3555,6 +3555,7 @@ static int gfx_v10_0_kcq_init_queue(struct amdgpu_ring *ring)
 
 		/* reset ring buffer */
 		ring->wptr = 0;
+		atomic64_set((atomic64_t *)&adev->wb.wb[ring->wptr_offs], 0);
 		amdgpu_ring_clear_ring(ring);
 	} else {
 		amdgpu_ring_clear_ring(ring);
diff --git a/drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c b/drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c
index d85e1e559c826..40034efa64bbc 100644
--- a/drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c
+++ b/drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c
@@ -3756,6 +3756,7 @@ static int gfx_v9_0_kcq_init_queue(struct amdgpu_ring *ring)
 
 		/* reset ring buffer */
 		ring->wptr = 0;
+		atomic64_set((atomic64_t *)&adev->wb.wb[ring->wptr_offs], 0);
 		amdgpu_ring_clear_ring(ring);
 	} else {
 		amdgpu_ring_clear_ring(ring);
-- 
2.20.1

[PATCH AUTOSEL 5.4 30/35] drm/amd/display: Clear link settings on MST disable connector

[Sasha Levin]

From: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>

[ Upstream commit 5ac7fd2f597b88ee81f4748ee50cab06192a8dc3 ]

[Why]
If we have a single MST display and we disconnect it, we dont disable that
link. This causes the old link settings to still exist

Now on a replug for MST we think its a link loss and will try to reallocate
mst payload which will fail, throwing warning below.

[  129.374192] [drm] Failed to updateMST allocation table forpipe idx:0
[  129.374206] ------------[ cut here ]------------
[  129.374284] WARNING: CPU: 14 PID: 1710 at
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc_link.c:3153
dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]

[  129.374285] Modules linked in: amdgpu(OE) amd_iommu_v2 gpu_sched ttm
drm_kms_helper drm fb_sys_fops syscopyarea sysfillrect sysimgblt
binfmt_misc nls_iso8859_1 edac_mce_amd snd_hda_codec_realtek
snd_hda_codec_generic ledtrig_audio kvm snd_hda_codec_hdmi snd_hda_intel
snd_intel_nhlt snd_hda_codec irqbypass snd_hda_core snd_hwdep snd_pcm
snd_seq_midi snd_seq_midi_event snd_rawmidi crct10dif_pclmul snd_seq
crc32_pclmul ghash_clmulni_intel snd_seq_device snd_timer snd aesni_intel
eeepc_wmi crypto_simd asus_wmi joydev cryptd sparse_keymap input_leds
soundcore video glue_helper wmi_bmof mxm_wmi k10temp ccp mac_hid
sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4
hid_generic usbhid hid igb i2c_algo_bit ahci dca i2c_piix4 libahci
gpio_amdpt wmi gpio_generic

[  129.374318] CPU: 14 PID: 1710 Comm: kworker/14:2 Tainted: G        W  OE     5.4.0-rc7bhawan+ #480
[  129.374318] Hardware name: System manufacturer System Product Name/PRIME X370-PRO, BIOS 0515 03/30/2017
[  129.374397] Workqueue: events dm_irq_work_func [amdgpu]
[  129.374468] RIP: 0010:dc_link_allocate_mst_payload+0x1f7/0x220 [amdgpu]
[  129.374470] Code: 52 20 e8 1c 63 ad f4 48 8b 5d d0 65 48 33 1c 25 28 00
00 00 b8 01 00 00 00 75 16 48 8d 65 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3
<0f> 0b e9 fa fe ff ff e8 ed 5b d6 f3 41 0f b6 b6 c4 02 00 00 48 c7
[  129.374471] RSP: 0018:ffff9f9141e7fcc0 EFLAGS: 00010246
[  129.374472] RAX: 0000000000000000 RBX: ffff91ef0762f800 RCX: 0000000000000000
[  129.374473] RDX: 0000000000000005 RSI: ffffffffc0c4a988 RDI: 0000000000000004
[  129.374474] RBP: ffff9f9141e7fd10 R08: 0000000000000005 R09: 0000000000000000
[  129.374475] R10: 0000000000000002 R11: 0000000000000001 R12: ffff91eebd510c00
[  129.374475] R13: ffff91eebd510e58 R14: ffff91ef052c01b8 R15: 0000000000000006
[  129.374476] FS:  0000000000000000(0000) GS:ffff91ef0ef80000(0000) knlGS:0000000000000000
[  129.374477] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  129.374478] CR2: 000055623ea01d50 CR3: 0000000408a8c000 CR4: 00000000003406e0
[  129.374479] Call Trace:
[  129.374550]  dc_link_reallocate_mst_payload+0x12e/0x150 [amdgpu]
[  129.374617]  dc_link_handle_hpd_rx_irq+0x6d4/0x6e0 [amdgpu]
[  129.374693]  handle_hpd_rx_irq+0x77/0x310 [amdgpu]
[  129.374768]  dm_irq_work_func+0x53/0x70 [amdgpu]
[  129.374774]  process_one_work+0x1fd/0x3f0
[  129.374776]  worker_thread+0x255/0x410
[  129.374778]  kthread+0x121/0x140
[  129.374780]  ? process_one_work+0x3f0/0x3f0
[  129.374781]  ? kthread_park+0x90/0x90
[  129.374785]  ret_from_fork+0x22/0x40

[How]
when we disable MST we should clear the cur link settings (lane_count=0 is
good enough). This will cause us to not reallocate payloads earlier than
expected and not throw the warning

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
index 16218a202b591..28a6c7b2ef4bb 100644
--- a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
+++ b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_mst_types.c
@@ -379,6 +379,7 @@ static void dm_dp_destroy_mst_connector(struct drm_dp_mst_topology_mgr *mgr,
 					   aconnector->dc_sink);
 		dc_sink_release(aconnector->dc_sink);
 		aconnector->dc_sink = NULL;
+		aconnector->dc_link->cur_link_settings.lane_count = 0;
 	}
 
 	drm_connector_unregister(connector);
-- 
2.20.1

[PATCH AUTOSEL 5.4 31/35] drm/amd/display: fix dcc swath size calculations on dcn1

[Sasha Levin]

From: Josip Pavic <Josip.Pavic@amd.com>

[ Upstream commit a0275dfc82c9034eefbeffd556cca6dd239d7925 ]

[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.

[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.

Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c b/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c
index a02c10e23e0d6..d163388c99a06 100644
--- a/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c
+++ b/drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hubbub.c
@@ -840,8 +840,8 @@ static void hubbub1_det_request_size(
 
 	hubbub1_get_blk256_size(&blk256_width, &blk256_height, bpe);
 
-	swath_bytes_horz_wc = height * blk256_height * bpe;
-	swath_bytes_vert_wc = width * blk256_width * bpe;
+	swath_bytes_horz_wc = width * blk256_height * bpe;
+	swath_bytes_vert_wc = height * blk256_width * bpe;
 
 	*req128_horz_wc = (2 * swath_bytes_horz_wc <= detile_buf_size) ?
 			false : /* full 256B request */
-- 
2.20.1

[PATCH AUTOSEL 5.4 32/35] xenbus: req->body should be updated before req->state

[Sasha Levin]

From: Dongli Zhang <dongli.zhang@oracle.com>

[ Upstream commit 1b6a51e86cce38cf4d48ce9c242120283ae2f603 ]

The req->body should be updated before req->state is updated and the
order should be guaranteed by a barrier.

Otherwise, read_reply() might return req->body = NULL.

Below is sample callstack when the issue is reproduced on purpose by
reordering the updates of req->body and req->state and adding delay in
code between updates of req->state and req->body.

[   22.356105] general protection fault: 0000 [#1] SMP PTI
[   22.361185] CPU: 2 PID: 52 Comm: xenwatch Not tainted 5.5.0xen+ #6
[   22.366727] Hardware name: Xen HVM domU, BIOS ...
[   22.372245] RIP: 0010:_parse_integer_fixup_radix+0x6/0x60
... ...
[   22.392163] RSP: 0018:ffffb2d64023fdf0 EFLAGS: 00010246
[   22.395933] RAX: 0000000000000000 RBX: 75746e7562755f6d RCX: 0000000000000000
[   22.400871] RDX: 0000000000000000 RSI: ffffb2d64023fdfc RDI: 75746e7562755f6d
[   22.405874] RBP: 0000000000000000 R08: 00000000000001e8 R09: 0000000000cdcdcd
[   22.410945] R10: ffffb2d6402ffe00 R11: ffff9d95395eaeb0 R12: ffff9d9535935000
[   22.417613] R13: ffff9d9526d4a000 R14: ffff9d9526f4f340 R15: ffff9d9537654000
[   22.423726] FS:  0000000000000000(0000) GS:ffff9d953bc80000(0000) knlGS:0000000000000000
[   22.429898] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   22.434342] CR2: 000000c4206a9000 CR3: 00000001ea3fc002 CR4: 00000000001606e0
[   22.439645] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   22.444941] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   22.450342] Call Trace:
[   22.452509]  simple_strtoull+0x27/0x70
[   22.455572]  xenbus_transaction_start+0x31/0x50
[   22.459104]  netback_changed+0x76c/0xcc1 [xen_netfront]
[   22.463279]  ? find_watch+0x40/0x40
[   22.466156]  xenwatch_thread+0xb4/0x150
[   22.469309]  ? wait_woken+0x80/0x80
[   22.472198]  kthread+0x10e/0x130
[   22.474925]  ? kthread_park+0x80/0x80
[   22.477946]  ret_from_fork+0x35/0x40
[   22.480968] Modules linked in: xen_kbdfront xen_fbfront(+) xen_netfront xen_blkfront
[   22.486783] ---[ end trace a9222030a747c3f7 ]---
[   22.490424] RIP: 0010:_parse_integer_fixup_radix+0x6/0x60

The virt_rmb() is added in the 'true' path of test_reply(). The "while"
is changed to "do while" so that test_reply() is used as a read memory
barrier.

Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Link: https://lore.kernel.org/r/20200303221423.21962-1-dongli.zhang@oracle.com
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/xen/xenbus/xenbus_comms.c | 2 ++
 drivers/xen/xenbus/xenbus_xs.c    | 9 ++++++---
 2 files changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/xen/xenbus/xenbus_comms.c b/drivers/xen/xenbus/xenbus_comms.c
index d239fc3c5e3de..852ed161fc2a7 100644
--- a/drivers/xen/xenbus/xenbus_comms.c
+++ b/drivers/xen/xenbus/xenbus_comms.c
@@ -313,6 +313,8 @@ static int process_msg(void)
 			req->msg.type = state.msg.type;
 			req->msg.len = state.msg.len;
 			req->body = state.body;
+			/* write body, then update state */
+			virt_wmb();
 			req->state = xb_req_state_got_reply;
 			req->cb(req);
 		} else
diff --git a/drivers/xen/xenbus/xenbus_xs.c b/drivers/xen/xenbus/xenbus_xs.c
index ddc18da61834e..3a06eb699f333 100644
--- a/drivers/xen/xenbus/xenbus_xs.c
+++ b/drivers/xen/xenbus/xenbus_xs.c
@@ -191,8 +191,11 @@ static bool xenbus_ok(void)
 
 static bool test_reply(struct xb_req_data *req)
 {
-	if (req->state == xb_req_state_got_reply || !xenbus_ok())
+	if (req->state == xb_req_state_got_reply || !xenbus_ok()) {
+		/* read req->state before all other fields */
+		virt_rmb();
 		return true;
+	}
 
 	/* Make sure to reread req->state each time. */
 	barrier();
@@ -202,7 +205,7 @@ static bool test_reply(struct xb_req_data *req)
 
 static void *read_reply(struct xb_req_data *req)
 {
-	while (req->state != xb_req_state_got_reply) {
+	do {
 		wait_event(req->wq, test_reply(req));
 
 		if (!xenbus_ok())
@@ -216,7 +219,7 @@ static void *read_reply(struct xb_req_data *req)
 		if (req->err)
 			return ERR_PTR(req->err);
 
-	}
+	} while (req->state != xb_req_state_got_reply);
 
 	return req->body;
 }
-- 
2.20.1

[PATCH AUTOSEL 5.4 33/35] xenbus: req->err should be updated before req->state

[Sasha Levin]

From: Dongli Zhang <dongli.zhang@oracle.com>

[ Upstream commit 8130b9d5b5abf26f9927b487c15319a187775f34 ]

This patch adds the barrier to guarantee that req->err is always updated
before req->state.

Otherwise, read_reply() would not return ERR_PTR(req->err) but
req->body, when process_writes()->xb_write() is failed.

Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Link: https://lore.kernel.org/r/20200303221423.21962-2-dongli.zhang@oracle.com
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/xen/xenbus/xenbus_comms.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/xen/xenbus/xenbus_comms.c b/drivers/xen/xenbus/xenbus_comms.c
index 852ed161fc2a7..eb5151fc8efab 100644
--- a/drivers/xen/xenbus/xenbus_comms.c
+++ b/drivers/xen/xenbus/xenbus_comms.c
@@ -397,6 +397,8 @@ static int process_writes(void)
 	if (state.req->state == xb_req_state_aborted)
 		kfree(state.req);
 	else {
+		/* write err, then update state */
+		virt_wmb();
 		state.req->state = xb_req_state_got_reply;
 		wake_up(&state.req->wq);
 	}
-- 
2.20.1

[PATCH AUTOSEL 5.4 34/35] block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()

[Sasha Levin]

From: Carlo Nonato <carlo.nonato95@gmail.com>

[ Upstream commit 14afc59361976c0ba39e3a9589c3eaa43ebc7e1d ]

The bfq_find_set_group() function takes as input a blkcg (which represents
a cgroup) and retrieves the corresponding bfq_group, then it updates the
bfq internal group hierarchy (see comments inside the function for why
this is needed) and finally it returns the bfq_group.
In the hierarchy update cycle, the pointer holding the correct bfq_group
that has to be returned is mistakenly used to traverse the hierarchy
bottom to top, meaning that in each iteration it gets overwritten with the
parent of the current group. Since the update cycle stops at root's
children (depth = 2), the overwrite becomes a problem only if the blkcg
describes a cgroup at a hierarchy level deeper than that (depth > 2). In
this case the root's child that happens to be also an ancestor of the
correct bfq_group is returned. The main consequence is that processes
contained in a cgroup at depth greater than 2 are wrongly placed in the
group described above by BFQ.

This commits fixes this problem by using a different bfq_group pointer in
the update cycle in order to avoid the overwrite of the variable holding
the original group reference.

Reported-by: Kwon Je Oh <kwonje.oh2@gmail.com>
Signed-off-by: Carlo Nonato <carlo.nonato95@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 block/bfq-cgroup.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/block/bfq-cgroup.c b/block/bfq-cgroup.c
index d0e36d6522649..86cd718e0380b 100644
--- a/block/bfq-cgroup.c
+++ b/block/bfq-cgroup.c
@@ -593,12 +593,13 @@ struct bfq_group *bfq_find_set_group(struct bfq_data *bfqd,
 	 */
 	entity = &bfqg->entity;
 	for_each_entity(entity) {
-		bfqg = container_of(entity, struct bfq_group, entity);
-		if (bfqg != bfqd->root_group) {
-			parent = bfqg_parent(bfqg);
+		struct bfq_group *curr_bfqg = container_of(entity,
+						struct bfq_group, entity);
+		if (curr_bfqg != bfqd->root_group) {
+			parent = bfqg_parent(curr_bfqg);
 			if (!parent)
 				parent = bfqd->root_group;
-			bfq_group_set_parent(bfqg, parent);
+			bfq_group_set_parent(curr_bfqg, parent);
 		}
 	}
 
-- 
2.20.1

[PATCH AUTOSEL 5.4 35/35] parse-maintainers: Mark as executable

[Sasha Levin]

From: Jonathan Neuschäfer <j.neuschaefer@gmx.net>

[ Upstream commit 611d61f9ac99dc9e1494473fb90117a960a89dfa ]

This makes the script more convenient to run.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 scripts/parse-maintainers.pl | 0
 1 file changed, 0 insertions(+), 0 deletions(-)
 mode change 100644 => 100755 scripts/parse-maintainers.pl

diff --git a/scripts/parse-maintainers.pl b/scripts/parse-maintainers.pl
old mode 100644
new mode 100755
-- 
2.20.1