[PATCH v4 0/3] media: i2c: imx219: Feature enhancements

[PATCH v4 0/3] media: i2c: imx219: Feature enhancements

[Lad Prabhakar]

This patch series does the following:
1: Makes sure the sensor is LP11 state on power up
2: Adds support for RAW8
3: Adds support for 640x480 resolution

Changes for v4:
1: Fixed review comments for patch 2/2 as request by Sakari.

Changes for v3:
1: Only patch 3/3 was posted for review.

Changes for v2:
1: Dropped setting the format in probe to coax the sensor to enter LP11
   state.
2: Fixed switching between RAW8/RAW10 modes.
3: Fixed fps setting for 640x480 and switched to auto mode.

Lad Prabhakar (3):
  media: i2c: imx219: Fix power sequence
  media: i2c: imx219: Add support for RAW8 bit bayer format
  media: i2c: imx219: Add support for cropped 640x480 resolution

 drivers/media/i2c/imx219.c | 235 ++++++++++++++++++++++++++++++++++++++-------
 1 file changed, 202 insertions(+), 33 deletions(-)

-- 
2.7.4

[PATCH v4 1/3] media: i2c: imx219: Fix power sequence

[Lad Prabhakar]

When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.

The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
---
 drivers/media/i2c/imx219.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index f1effb5..16010ca 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -1224,6 +1224,23 @@ static int imx219_probe(struct i2c_client *client)
 	/* Set default mode to max resolution */
 	imx219->mode = &supported_modes[0];
 
+	/* sensor doesn't enter LP-11 state upon power up until and unless
+	 * streaming is started, so upon power up switch the modes to:
+	 * streaming -> standby
+	 */
+	ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
+			       IMX219_REG_VALUE_08BIT, IMX219_MODE_STREAMING);
+	if (ret < 0)
+		goto error_power_off;
+	usleep_range(100, 110);
+
+	/* put sensor back to standby mode */
+	ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
+			       IMX219_REG_VALUE_08BIT, IMX219_MODE_STANDBY);
+	if (ret < 0)
+		goto error_power_off;
+	usleep_range(100, 110);
+
 	ret = imx219_init_controls(imx219);
 	if (ret)
 		goto error_power_off;
-- 
2.7.4

[PATCH v4 2/3] media: i2c: imx219: Add support for RAW8 bit bayer format

[Lad Prabhakar]

IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
---
 drivers/media/i2c/imx219.c | 148 +++++++++++++++++++++++++++++++++++----------
 1 file changed, 116 insertions(+), 32 deletions(-)

diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index 16010ca..3207487 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -168,15 +168,12 @@ static const struct imx219_reg mode_3280x2464_regs[] = {
 	{0x0171, 0x01},
 	{0x0174, 0x00},
 	{0x0175, 0x00},
-	{0x018c, 0x0a},
-	{0x018d, 0x0a},
 	{0x0301, 0x05},
 	{0x0303, 0x01},
 	{0x0304, 0x03},
 	{0x0305, 0x03},
 	{0x0306, 0x00},
 	{0x0307, 0x39},
-	{0x0309, 0x0a},
 	{0x030b, 0x01},
 	{0x030c, 0x00},
 	{0x030d, 0x72},
@@ -230,15 +227,12 @@ static const struct imx219_reg mode_1920_1080_regs[] = {
 	{0x0171, 0x01},
 	{0x0174, 0x00},
 	{0x0175, 0x00},
-	{0x018c, 0x0a},
-	{0x018d, 0x0a},
 	{0x0301, 0x05},
 	{0x0303, 0x01},
 	{0x0304, 0x03},
 	{0x0305, 0x03},
 	{0x0306, 0x00},
 	{0x0307, 0x39},
-	{0x0309, 0x0a},
 	{0x030b, 0x01},
 	{0x030c, 0x00},
 	{0x030d, 0x72},
@@ -290,15 +284,12 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
 	{0x0171, 0x01},
 	{0x0174, 0x01},
 	{0x0175, 0x01},
-	{0x018c, 0x0a},
-	{0x018d, 0x0a},
 	{0x0301, 0x05},
 	{0x0303, 0x01},
 	{0x0304, 0x03},
 	{0x0305, 0x03},
 	{0x0306, 0x00},
 	{0x0307, 0x39},
-	{0x0309, 0x0a},
 	{0x030b, 0x01},
 	{0x030c, 0x00},
 	{0x030d, 0x72},
@@ -322,6 +313,18 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
 	{0x0163, 0x78},
 };
 
+static const struct imx219_reg raw8_framefmt_regs[] = {
+	{0x018c, 0x08},
+	{0x018d, 0x08},
+	{0x0309, 0x08},
+};
+
+static const struct imx219_reg raw10_framefmt_regs[] = {
+	{0x018c, 0x0a},
+	{0x018d, 0x0a},
+	{0x0309, 0x0a},
+};
+
 static const char * const imx219_test_pattern_menu[] = {
 	"Disabled",
 	"Color Bars",
@@ -349,6 +352,27 @@ static const char * const imx219_supply_name[] = {
 #define IMX219_NUM_SUPPLIES ARRAY_SIZE(imx219_supply_name)
 
 /*
+ * The supported formats.
+ * This table MUST contain 4 entries per format, to cover the various flip
+ * combinations in the order
+ * - no flip
+ * - h flip
+ * - v flip
+ * - h&v flips
+ */
+static const u32 codes[] = {
+	MEDIA_BUS_FMT_SRGGB10_1X10,
+	MEDIA_BUS_FMT_SGRBG10_1X10,
+	MEDIA_BUS_FMT_SGBRG10_1X10,
+	MEDIA_BUS_FMT_SBGGR10_1X10,
+
+	MEDIA_BUS_FMT_SRGGB8_1X8,
+	MEDIA_BUS_FMT_SGRBG8_1X8,
+	MEDIA_BUS_FMT_SGBRG8_1X8,
+	MEDIA_BUS_FMT_SBGGR8_1X8,
+};
+
+/*
  * Initialisation delay between XCLR low->high and the moment when the sensor
  * can start capture (i.e. can leave software stanby) must be not less than:
  *   t4 + max(t5, t6 + <time to initialize the sensor register over I2C>)
@@ -413,6 +437,8 @@ struct imx219 {
 	struct v4l2_subdev sd;
 	struct media_pad pad;
 
+	struct v4l2_mbus_framefmt fmt;
+
 	struct clk *xclk; /* system clock to IMX219 */
 	u32 xclk_freq;
 
@@ -519,19 +545,40 @@ static int imx219_write_regs(struct imx219 *imx219,
 }
 
 /* Get bayer order based on flip setting. */
-static u32 imx219_get_format_code(struct imx219 *imx219)
+static u32 imx219_get_format_code(struct imx219 *imx219, u32 code)
 {
-	/*
-	 * Only one bayer order is supported.
-	 * It depends on the flip settings.
-	 */
-	static const u32 codes[2][2] = {
-		{ MEDIA_BUS_FMT_SRGGB10_1X10, MEDIA_BUS_FMT_SGRBG10_1X10, },
-		{ MEDIA_BUS_FMT_SGBRG10_1X10, MEDIA_BUS_FMT_SBGGR10_1X10, },
-	};
+	unsigned int i;
 
 	lockdep_assert_held(&imx219->mutex);
-	return codes[imx219->vflip->val][imx219->hflip->val];
+
+	for (i = 0; i < ARRAY_SIZE(codes); i++)
+		if (codes[i] == code)
+			break;
+
+	if (i >= ARRAY_SIZE(codes))
+		i = 0;
+
+	i = (i & ~3) | (imx219->vflip->val ? 2 : 0) |
+	    (imx219->hflip->val ? 1 : 0);
+
+	return codes[i];
+}
+
+static void imx219_set_default_format(struct imx219 *imx219)
+{
+	struct v4l2_mbus_framefmt *fmt;
+
+	fmt = &imx219->fmt;
+	fmt->code = MEDIA_BUS_FMT_SRGGB10_1X10;
+	fmt->colorspace = V4L2_COLORSPACE_SRGB;
+	fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->colorspace);
+	fmt->quantization = V4L2_MAP_QUANTIZATION_DEFAULT(true,
+							  fmt->colorspace,
+							  fmt->ycbcr_enc);
+	fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace);
+	fmt->width = supported_modes[0].width;
+	fmt->height = supported_modes[0].height;
+	fmt->field = V4L2_FIELD_NONE;
 }
 
 static int imx219_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
@@ -545,7 +592,8 @@ static int imx219_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
 	/* Initialize try_fmt */
 	try_fmt->width = supported_modes[0].width;
 	try_fmt->height = supported_modes[0].height;
-	try_fmt->code = imx219_get_format_code(imx219);
+	try_fmt->code = imx219_get_format_code(imx219,
+					       MEDIA_BUS_FMT_SRGGB10_1X10);
 	try_fmt->field = V4L2_FIELD_NONE;
 
 	mutex_unlock(&imx219->mutex);
@@ -648,14 +696,10 @@ static int imx219_enum_mbus_code(struct v4l2_subdev *sd,
 {
 	struct imx219 *imx219 = to_imx219(sd);
 
-	/*
-	 * Only one bayer order is supported (though it depends on the flip
-	 * settings)
-	 */
-	if (code->index > 0)
+	if (code->index >= (ARRAY_SIZE(codes) / 4))
 		return -EINVAL;
 
-	code->code = imx219_get_format_code(imx219);
+	code->code = imx219_get_format_code(imx219, codes[code->index * 4]);
 
 	return 0;
 }
@@ -669,7 +713,7 @@ static int imx219_enum_frame_size(struct v4l2_subdev *sd,
 	if (fse->index >= ARRAY_SIZE(supported_modes))
 		return -EINVAL;
 
-	if (fse->code != imx219_get_format_code(imx219))
+	if (fse->code != imx219_get_format_code(imx219, imx219->fmt.code))
 		return -EINVAL;
 
 	fse->min_width = supported_modes[fse->index].width;
@@ -696,9 +740,7 @@ static void imx219_update_pad_format(struct imx219 *imx219,
 {
 	fmt->format.width = mode->width;
 	fmt->format.height = mode->height;
-	fmt->format.code = imx219_get_format_code(imx219);
 	fmt->format.field = V4L2_FIELD_NONE;
-
 	imx219_reset_colorspace(&fmt->format);
 }
 
@@ -710,10 +752,12 @@ static int __imx219_get_pad_format(struct imx219 *imx219,
 		struct v4l2_mbus_framefmt *try_fmt =
 			v4l2_subdev_get_try_format(&imx219->sd, cfg, fmt->pad);
 		/* update the code which could change due to vflip or hflip: */
-		try_fmt->code = imx219_get_format_code(imx219);
+		try_fmt->code = imx219_get_format_code(imx219, try_fmt->code);
 		fmt->format = *try_fmt;
 	} else {
 		imx219_update_pad_format(imx219, imx219->mode, fmt);
+		fmt->format.code = imx219_get_format_code(imx219,
+							  imx219->fmt.code);
 	}
 
 	return 0;
@@ -741,11 +785,18 @@ static int imx219_set_pad_format(struct v4l2_subdev *sd,
 	const struct imx219_mode *mode;
 	struct v4l2_mbus_framefmt *framefmt;
 	int exposure_max, exposure_def, hblank;
+	unsigned int i;
 
 	mutex_lock(&imx219->mutex);
 
+	for (i = 0; i < ARRAY_SIZE(codes); i++)
+		if (codes[i] == fmt->format.code)
+			break;
+	if (i >= ARRAY_SIZE(codes))
+		i = 0;
+
 	/* Bayer order varies with flips */
-	fmt->format.code = imx219_get_format_code(imx219);
+	fmt->format.code = imx219_get_format_code(imx219, codes[i]);
 
 	mode = v4l2_find_nearest_size(supported_modes,
 				      ARRAY_SIZE(supported_modes),
@@ -755,7 +806,9 @@ static int imx219_set_pad_format(struct v4l2_subdev *sd,
 	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
 		framefmt = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
 		*framefmt = fmt->format;
-	} else if (imx219->mode != mode) {
+	} else if (imx219->mode != mode ||
+		   imx219->fmt.code != fmt->format.code) {
+		imx219->fmt = fmt->format;
 		imx219->mode = mode;
 		/* Update limits and set FPS to default */
 		__v4l2_ctrl_modify_range(imx219->vblank, IMX219_VBLANK_MIN,
@@ -786,6 +839,27 @@ static int imx219_set_pad_format(struct v4l2_subdev *sd,
 	return 0;
 }
 
+static int imx219_set_framefmt(struct imx219 *imx219)
+{
+	switch (imx219->fmt.code) {
+	case MEDIA_BUS_FMT_SRGGB8_1X8:
+	case MEDIA_BUS_FMT_SGRBG8_1X8:
+	case MEDIA_BUS_FMT_SGBRG8_1X8:
+	case MEDIA_BUS_FMT_SBGGR8_1X8:
+		return imx219_write_regs(imx219, raw8_framefmt_regs,
+					ARRAY_SIZE(raw8_framefmt_regs));
+
+	case MEDIA_BUS_FMT_SRGGB10_1X10:
+	case MEDIA_BUS_FMT_SGRBG10_1X10:
+	case MEDIA_BUS_FMT_SGBRG10_1X10:
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+		return imx219_write_regs(imx219, raw10_framefmt_regs,
+					ARRAY_SIZE(raw10_framefmt_regs));
+	}
+
+	return -EINVAL;
+}
+
 static int imx219_start_streaming(struct imx219 *imx219)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
@@ -800,6 +874,13 @@ static int imx219_start_streaming(struct imx219 *imx219)
 		return ret;
 	}
 
+	ret = imx219_set_framefmt(imx219);
+	if (ret) {
+		dev_err(&client->dev, "%s failed to set frame format: %d\n",
+			__func__, ret);
+		return ret;
+	}
+
 	/* Apply customized values from user */
 	ret =  __v4l2_ctrl_handler_setup(imx219->sd.ctrl_handler);
 	if (ret)
@@ -1253,6 +1334,9 @@ static int imx219_probe(struct i2c_client *client)
 	/* Initialize source pad */
 	imx219->pad.flags = MEDIA_PAD_FL_SOURCE;
 
+	/* Initialize default format */
+	imx219_set_default_format(imx219);
+
 	ret = media_entity_pads_init(&imx219->sd.entity, 1, &imx219->pad);
 	if (ret) {
 		dev_err(dev, "failed to init entity pads: %d\n", ret);
-- 
2.7.4

[PATCH v4 3/3] media: i2c: imx219: Add support for cropped 640x480 resolution

[Lad Prabhakar]

This patch adds mode table entry for capturing cropped 640x480 resolution

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
---
 drivers/media/i2c/imx219.c | 70 +++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 69 insertions(+), 1 deletion(-)

diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index 3207487..cb03bde 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -54,6 +54,7 @@
 #define IMX219_VTS_15FPS		0x0dc6
 #define IMX219_VTS_30FPS_1080P		0x06e3
 #define IMX219_VTS_30FPS_BINNED		0x06e3
+#define IMX219_VTS_30FPS_640x480	0x06e3
 #define IMX219_VTS_MAX			0xffff
 
 #define IMX219_VBLANK_MIN		4
@@ -138,7 +139,7 @@ struct imx219_mode {
 /*
  * Register sets lifted off the i2C interface from the Raspberry Pi firmware
  * driver.
- * 3280x2464 = mode 2, 1920x1080 = mode 1, and 1640x1232 = mode 4.
+ * 3280x2464 = mode 2, 1920x1080 = mode 1, 1640x1232 = mode 4, 640x480 = mode 7.
  */
 static const struct imx219_reg mode_3280x2464_regs[] = {
 	{0x0100, 0x00},
@@ -313,6 +314,63 @@ static const struct imx219_reg mode_1640_1232_regs[] = {
 	{0x0163, 0x78},
 };
 
+static const struct imx219_reg mode_640_480_regs[] = {
+	{0x0100, 0x00},
+	{0x30eb, 0x05},
+	{0x30eb, 0x0c},
+	{0x300a, 0xff},
+	{0x300b, 0xff},
+	{0x30eb, 0x05},
+	{0x30eb, 0x09},
+	{0x0114, 0x01},
+	{0x0128, 0x00},
+	{0x012a, 0x18},
+	{0x012b, 0x00},
+	{0x0162, 0x0d},
+	{0x0163, 0x78},
+	{0x0164, 0x03},
+	{0x0165, 0xe8},
+	{0x0166, 0x08},
+	{0x0167, 0xe7},
+	{0x0168, 0x02},
+	{0x0169, 0xf0},
+	{0x016a, 0x06},
+	{0x016b, 0xaf},
+	{0x016c, 0x02},
+	{0x016d, 0x80},
+	{0x016e, 0x01},
+	{0x016f, 0xe0},
+	{0x0170, 0x01},
+	{0x0171, 0x01},
+	{0x0174, 0x03},
+	{0x0175, 0x03},
+	{0x0301, 0x05},
+	{0x0303, 0x01},
+	{0x0304, 0x03},
+	{0x0305, 0x03},
+	{0x0306, 0x00},
+	{0x0307, 0x39},
+	{0x030b, 0x01},
+	{0x030c, 0x00},
+	{0x030d, 0x72},
+	{0x0624, 0x06},
+	{0x0625, 0x68},
+	{0x0626, 0x04},
+	{0x0627, 0xd0},
+	{0x455e, 0x00},
+	{0x471e, 0x4b},
+	{0x4767, 0x0f},
+	{0x4750, 0x14},
+	{0x4540, 0x00},
+	{0x47b4, 0x14},
+	{0x4713, 0x30},
+	{0x478b, 0x10},
+	{0x478f, 0x10},
+	{0x4793, 0x10},
+	{0x4797, 0x0e},
+	{0x479b, 0x0e},
+};
+
 static const struct imx219_reg raw8_framefmt_regs[] = {
 	{0x018c, 0x08},
 	{0x018d, 0x08},
@@ -431,6 +489,16 @@ static const struct imx219_mode supported_modes[] = {
 			.regs = mode_1640_1232_regs,
 		},
 	},
+	{
+		/* 640x480 30fps mode */
+		.width = 640,
+		.height = 480,
+		.vts_def = IMX219_VTS_30FPS_640x480,
+		.reg_list = {
+			.num_of_regs = ARRAY_SIZE(mode_640_480_regs),
+			.regs = mode_640_480_regs,
+		},
+	},
 };
 
 struct imx219 {
-- 
2.7.4

Re: [PATCH v4 0/3] media: i2c: imx219: Feature enhancements

[Marcus Folkesson]

Hi,

To which tree does this patchset apply?

On Tue, Mar 10, 2020 at 01:17:06PM +0000, Lad Prabhakar wrote:
> This patch series does the following:
> 1: Makes sure the sensor is LP11 state on power up
> 2: Adds support for RAW8
> 3: Adds support for 640x480 resolution
> 
> Changes for v4:
> 1: Fixed review comments for patch 2/2 as request by Sakari.
> 
> Changes for v3:
> 1: Only patch 3/3 was posted for review.
> 
> Changes for v2:
> 1: Dropped setting the format in probe to coax the sensor to enter LP11
>    state.
> 2: Fixed switching between RAW8/RAW10 modes.
> 3: Fixed fps setting for 640x480 and switched to auto mode.
> 
> Lad Prabhakar (3):
>   media: i2c: imx219: Fix power sequence
>   media: i2c: imx219: Add support for RAW8 bit bayer format
>   media: i2c: imx219: Add support for cropped 640x480 resolution
> 
>  drivers/media/i2c/imx219.c | 235 ++++++++++++++++++++++++++++++++++++++-------
>  1 file changed, 202 insertions(+), 33 deletions(-)
> 
> -- 
> 2.7.4
> 


Thanks,
Marcus Folkesson

RE: [PATCH v4 0/3] media: i2c: imx219: Feature enhancements

[Prabhakar Mahadev Lad]

Hi Marcus,

> -----Original Message-----
> From: Marcus Folkesson <marcus.folkesson@gmail.com>
> Sent: 17 March 2020 08:02
> To: Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>
> Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>; Sakari Ailus
> <sakari.ailus@linux.intel.com>; Mauro Carvalho Chehab
> <mchehab@kernel.org>; linux-media@vger.kernel.org; linux-
> kernel@vger.kernel.org; Lad Prabhakar <prabhakar.csengg@gmail.com>
> Subject: Re: [PATCH v4 0/3] media: i2c: imx219: Feature enhancements
>
> Hi,
>
> To which tree does this patchset apply?
>
These patches apply to media_tree [1], btw v4 patches have been accepted and  merged into master branch of media_tree.

[1] https://git.linuxtv.org//media_tree.git

Cheers,
--Prabhakar

> On Tue, Mar 10, 2020 at 01:17:06PM +0000, Lad Prabhakar wrote:
> > This patch series does the following:
> > 1: Makes sure the sensor is LP11 state on power up
> > 2: Adds support for RAW8
> > 3: Adds support for 640x480 resolution
> >
> > Changes for v4:
> > 1: Fixed review comments for patch 2/2 as request by Sakari.
> >
> > Changes for v3:
> > 1: Only patch 3/3 was posted for review.
> >
> > Changes for v2:
> > 1: Dropped setting the format in probe to coax the sensor to enter LP11
> >    state.
> > 2: Fixed switching between RAW8/RAW10 modes.
> > 3: Fixed fps setting for 640x480 and switched to auto mode.
> >
> > Lad Prabhakar (3):
> >   media: i2c: imx219: Fix power sequence
> >   media: i2c: imx219: Add support for RAW8 bit bayer format
> >   media: i2c: imx219: Add support for cropped 640x480 resolution
> >
> >  drivers/media/i2c/imx219.c | 235
> ++++++++++++++++++++++++++++++++++++++-------
> >  1 file changed, 202 insertions(+), 33 deletions(-)
> >
> > --
> > 2.7.4
> >
>
>
> Thanks,
> Marcus Folkesson


Renesas Electronics Europe GmbH, Geschaeftsfuehrer/President: Carsten Jauch, Sitz der Gesellschaft/Registered office: Duesseldorf, Arcadiastrasse 10, 40472 Duesseldorf, Germany, Handelsregister/Commercial Register: Duesseldorf, HRB 3708 USt-IDNr./Tax identification no.: DE 119353406 WEEE-Reg.-Nr./WEEE reg. no.: DE 14978647

Re: [PATCH v4 0/3] media: i2c: imx219: Feature enhancements

[Marcus Folkesson]

Hi Prabhakar,

On Tue, Mar 17, 2020 at 08:03:49AM +0000, Prabhakar Mahadev Lad wrote:
> Hi Marcus,
> 
> > -----Original Message-----
> > From: Marcus Folkesson <marcus.folkesson@gmail.com>
> > Sent: 17 March 2020 08:02
> > To: Prabhakar Mahadev Lad <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>; Sakari Ailus
> > <sakari.ailus@linux.intel.com>; Mauro Carvalho Chehab
> > <mchehab@kernel.org>; linux-media@vger.kernel.org; linux-
> > kernel@vger.kernel.org; Lad Prabhakar <prabhakar.csengg@gmail.com>
> > Subject: Re: [PATCH v4 0/3] media: i2c: imx219: Feature enhancements
> >
> > Hi,
> >
> > To which tree does this patchset apply?
> >
> These patches apply to media_tree [1], btw v4 patches have been accepted and  merged into master branch of media_tree.

Thank you and good work!

> 
> [1] https://git.linuxtv.org//media_tree.git
> 
> Cheers,
> --Prabhakar

Best regards
Marcus Folkesson