* [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb
@ 2020-04-14 3:10 Qiang Zhao
2020-04-14 3:10 ` [RESEND 2/2] ls1043ardb: add ds26522 node to dts Qiang Zhao
2020-04-28 8:56 ` [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb Shawn Guo
0 siblings, 2 replies; 3+ messages in thread
From: Qiang Zhao @ 2020-04-14 3:10 UTC (permalink / raw)
To: shawnguo; +Cc: leoyang.li, devicetree, linux-kernel, Zhao Qiang
From: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts | 16 ++++++
arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 66 +++++++++++++++++++++++
2 files changed, 82 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
index 4223a23..96e87ba 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
@@ -96,6 +96,22 @@
};
};
+&uqe {
+ ucc_hdlc: ucc@2000 {
+ compatible = "fsl,ucc-hdlc";
+ rx-clock-name = "clk8";
+ tx-clock-name = "clk9";
+ fsl,rx-sync-clock = "rsync_pin";
+ fsl,tx-sync-clock = "tsync_pin";
+ fsl,tx-timeslot-mask = <0xfffffffe>;
+ fsl,rx-timeslot-mask = <0xfffffffe>;
+ fsl,tdm-framer-type = "e1";
+ fsl,tdm-id = <0>;
+ fsl,siram-entry-id = <0>;
+ fsl,tdm-interface;
+ };
+};
+
&duart0 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
index c084c7a4..a6f2b15 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
@@ -525,6 +525,72 @@
#interrupt-cells = <2>;
};
+ uqe: uqe@2400000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "qe";
+ compatible = "fsl,qe", "simple-bus";
+ ranges = <0x0 0x0 0x2400000 0x40000>;
+ reg = <0x0 0x2400000 0x0 0x480>;
+ brg-frequency = <100000000>;
+ bus-frequency = <200000000>;
+
+ fsl,qe-num-riscs = <1>;
+ fsl,qe-num-snums = <28>;
+
+ qeic: qeic@80 {
+ compatible = "fsl,qe-ic";
+ reg = <0x80 0x80>;
+ #address-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupts = <0 77 0x04 0 77 0x04>;
+ };
+
+ si1: si@700 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,ls1043-qe-si",
+ "fsl,t1040-qe-si";
+ reg = <0x700 0x80>;
+ };
+
+ siram1: siram@1000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,ls1043-qe-siram",
+ "fsl,t1040-qe-siram";
+ reg = <0x1000 0x800>;
+ };
+
+ ucc@2000 {
+ cell-index = <1>;
+ reg = <0x2000 0x200>;
+ interrupts = <32>;
+ interrupt-parent = <&qeic>;
+ };
+
+ ucc@2200 {
+ cell-index = <3>;
+ reg = <0x2200 0x200>;
+ interrupts = <34>;
+ interrupt-parent = <&qeic>;
+ };
+
+ muram@10000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,qe-muram", "fsl,cpm-muram";
+ ranges = <0x0 0x10000 0x6000>;
+
+ data-only@0 {
+ compatible = "fsl,qe-muram-data",
+ "fsl,cpm-muram-data";
+ reg = <0x0 0x6000>;
+ };
+ };
+ };
+
lpuart0: serial@2950000 {
compatible = "fsl,ls1021a-lpuart";
reg = <0x0 0x2950000 0x0 0x1000>;
--
2.9.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [RESEND 2/2] ls1043ardb: add ds26522 node to dts
2020-04-14 3:10 [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb Qiang Zhao
@ 2020-04-14 3:10 ` Qiang Zhao
2020-04-28 8:56 ` [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Qiang Zhao @ 2020-04-14 3:10 UTC (permalink / raw)
To: shawnguo; +Cc: leoyang.li, devicetree, linux-kernel, Zhao Qiang
From: Zhao Qiang <qiang.zhao@nxp.com>
add ds26522 node to fsl-ls1043a-rdb.dts
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts | 16 ++++++++++++++++
1 file changed, 16 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
index 96e87ba..b60c742 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
@@ -94,6 +94,22 @@
reg = <0>;
spi-max-frequency = <1000000>; /* input clock */
};
+
+ slic@2 {
+ compatible = "maxim,ds26522";
+ reg = <2>;
+ spi-max-frequency = <2000000>;
+ fsl,spi-cs-sck-delay = <100>;
+ fsl,spi-sck-cs-delay = <50>;
+ };
+
+ slic@3 {
+ compatible = "maxim,ds26522";
+ reg = <3>;
+ spi-max-frequency = <2000000>;
+ fsl,spi-cs-sck-delay = <100>;
+ fsl,spi-sck-cs-delay = <50>;
+ };
};
&uqe {
--
2.9.5
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb
2020-04-14 3:10 [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb Qiang Zhao
2020-04-14 3:10 ` [RESEND 2/2] ls1043ardb: add ds26522 node to dts Qiang Zhao
@ 2020-04-28 8:56 ` Shawn Guo
1 sibling, 0 replies; 3+ messages in thread
From: Shawn Guo @ 2020-04-28 8:56 UTC (permalink / raw)
To: Qiang Zhao; +Cc: leoyang.li, devicetree, linux-kernel
On Tue, Apr 14, 2020 at 11:10:28AM +0800, Qiang Zhao wrote:
> From: Zhao Qiang <qiang.zhao@nxp.com>
>
Please write a proper commit log.
> Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Subject should be prefixed like 'arm64: dts: ...'
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts | 16 ++++++
> arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 66 +++++++++++++++++++++++
> 2 files changed, 82 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
> index 4223a23..96e87ba 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
> @@ -96,6 +96,22 @@
> };
> };
>
> +&uqe {
> + ucc_hdlc: ucc@2000 {
> + compatible = "fsl,ucc-hdlc";
> + rx-clock-name = "clk8";
> + tx-clock-name = "clk9";
> + fsl,rx-sync-clock = "rsync_pin";
> + fsl,tx-sync-clock = "tsync_pin";
> + fsl,tx-timeslot-mask = <0xfffffffe>;
> + fsl,rx-timeslot-mask = <0xfffffffe>;
> + fsl,tdm-framer-type = "e1";
> + fsl,tdm-id = <0>;
> + fsl,siram-entry-id = <0>;
> + fsl,tdm-interface;
> + };
> +};
> +
> &duart0 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
> index c084c7a4..a6f2b15 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
> @@ -525,6 +525,72 @@
> #interrupt-cells = <2>;
> };
>
> + uqe: uqe@2400000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + device_type = "qe";
> + compatible = "fsl,qe", "simple-bus";
> + ranges = <0x0 0x0 0x2400000 0x40000>;
> + reg = <0x0 0x2400000 0x0 0x480>;
> + brg-frequency = <100000000>;
> + bus-frequency = <200000000>;
> +
Drop this newline.
Shawn
> + fsl,qe-num-riscs = <1>;
> + fsl,qe-num-snums = <28>;
> +
> + qeic: qeic@80 {
> + compatible = "fsl,qe-ic";
> + reg = <0x80 0x80>;
> + #address-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + interrupts = <0 77 0x04 0 77 0x04>;
> + };
> +
> + si1: si@700 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "fsl,ls1043-qe-si",
> + "fsl,t1040-qe-si";
> + reg = <0x700 0x80>;
> + };
> +
> + siram1: siram@1000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,ls1043-qe-siram",
> + "fsl,t1040-qe-siram";
> + reg = <0x1000 0x800>;
> + };
> +
> + ucc@2000 {
> + cell-index = <1>;
> + reg = <0x2000 0x200>;
> + interrupts = <32>;
> + interrupt-parent = <&qeic>;
> + };
> +
> + ucc@2200 {
> + cell-index = <3>;
> + reg = <0x2200 0x200>;
> + interrupts = <34>;
> + interrupt-parent = <&qeic>;
> + };
> +
> + muram@10000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,qe-muram", "fsl,cpm-muram";
> + ranges = <0x0 0x10000 0x6000>;
> +
> + data-only@0 {
> + compatible = "fsl,qe-muram-data",
> + "fsl,cpm-muram-data";
> + reg = <0x0 0x6000>;
> + };
> + };
> + };
> +
> lpuart0: serial@2950000 {
> compatible = "fsl,ls1021a-lpuart";
> reg = <0x0 0x2950000 0x0 0x1000>;
> --
> 2.9.5
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-04-28 8:56 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-04-14 3:10 [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb Qiang Zhao
2020-04-14 3:10 ` [RESEND 2/2] ls1043ardb: add ds26522 node to dts Qiang Zhao
2020-04-28 8:56 ` [RESEND 1/2] ls1043ardb: add qe node to ls1043ardb Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).