* [PATCH v6 3/5] iio: vcnl4000: Add event support for VCNL4010/20.
2020-04-27 9:55 [PATCH v6 0/5] iio: vcnl: Add interrupts support for VCNL4010/20 Mathieu Othacehe
2020-04-27 9:55 ` [PATCH v6 1/5] iio: vcnl4000: Fix i2c swapped word reading Mathieu Othacehe
2020-04-27 9:55 ` [PATCH v6 2/5] iio: vcnl4000: Factorize data reading and writing Mathieu Othacehe
@ 2020-04-27 9:55 ` Mathieu Othacehe
2020-04-27 9:55 ` [PATCH v6 4/5] iio: vcnl4000: Add sampling frequency " Mathieu Othacehe
2020-04-27 9:55 ` [PATCH v6 5/5] iio: vcnl4000: Add buffer " Mathieu Othacehe
4 siblings, 0 replies; 9+ messages in thread
From: Mathieu Othacehe @ 2020-04-27 9:55 UTC (permalink / raw)
To: jic23, knaack.h, lars, pmeerw; +Cc: linux-iio, linux-kernel, Mathieu Othacehe
The VCNL4010 and VCNL4020 chips are able to raise interrupts on proximity
threshold events. Add support for threshold rising and falling events for
those two chips.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
---
drivers/iio/light/vcnl4000.c | 454 ++++++++++++++++++++++++++++++-----
1 file changed, 392 insertions(+), 62 deletions(-)
diff --git a/drivers/iio/light/vcnl4000.c b/drivers/iio/light/vcnl4000.c
index b976e29f2fda..e7653037fa5d 100644
--- a/drivers/iio/light/vcnl4000.c
+++ b/drivers/iio/light/vcnl4000.c
@@ -13,7 +13,6 @@
*
* TODO:
* allow to adjust IR current
- * proximity threshold and event handling
* periodic ALS/proximity measurement (VCNL4010/20)
* interrupts (VCNL4010/20/40, VCNL4200)
*/
@@ -23,7 +22,9 @@
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/pm_runtime.h>
+#include <linux/interrupt.h>
+#include <linux/iio/events.h>
#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>
@@ -35,14 +36,22 @@
#define VCNL4000_COMMAND 0x80 /* Command register */
#define VCNL4000_PROD_REV 0x81 /* Product ID and Revision ID */
+#define VCNL4010_PROX_RATE 0x82 /* Proximity rate */
#define VCNL4000_LED_CURRENT 0x83 /* IR LED current for proximity mode */
#define VCNL4000_AL_PARAM 0x84 /* Ambient light parameter register */
+#define VCNL4010_ALS_PARAM 0x84 /* ALS rate */
#define VCNL4000_AL_RESULT_HI 0x85 /* Ambient light result register, MSB */
#define VCNL4000_AL_RESULT_LO 0x86 /* Ambient light result register, LSB */
#define VCNL4000_PS_RESULT_HI 0x87 /* Proximity result register, MSB */
#define VCNL4000_PS_RESULT_LO 0x88 /* Proximity result register, LSB */
#define VCNL4000_PS_MEAS_FREQ 0x89 /* Proximity test signal frequency */
+#define VCNL4010_INT_CTRL 0x89 /* Interrupt control */
#define VCNL4000_PS_MOD_ADJ 0x8a /* Proximity modulator timing adjustment */
+#define VCNL4010_LOW_THR_HI 0x8a /* Low threshold, MSB */
+#define VCNL4010_LOW_THR_LO 0x8b /* Low threshold, LSB */
+#define VCNL4010_HIGH_THR_HI 0x8c /* High threshold, MSB */
+#define VCNL4010_HIGH_THR_LO 0x8d /* High threshold, LSB */
+#define VCNL4010_ISR 0x8e /* Interrupt status */
#define VCNL4200_AL_CONF 0x00 /* Ambient light configuration */
#define VCNL4200_PS_CONF1 0x03 /* Proximity configuration */
@@ -57,6 +66,26 @@
#define VCNL4000_PS_RDY BIT(5) /* proximity data ready? */
#define VCNL4000_AL_OD BIT(4) /* start on-demand ALS measurement */
#define VCNL4000_PS_OD BIT(3) /* start on-demand proximity measurement */
+#define VCNL4000_ALS_EN BIT(2) /* start ALS measurement */
+#define VCNL4000_PROX_EN BIT(1) /* start proximity measurement */
+#define VCNL4000_SELF_TIMED_EN BIT(0) /* start self-timed measurement */
+
+/* Bit masks for interrupt registers. */
+#define VCNL4010_INT_THR_SEL BIT(0) /* Select threshold interrupt source */
+#define VCNL4010_INT_THR_EN BIT(1) /* Threshold interrupt type */
+#define VCNL4010_INT_ALS_EN BIT(2) /* Enable on ALS data ready */
+#define VCNL4010_INT_PROX_EN BIT(3) /* Enable on proximity data ready */
+
+#define VCNL4010_INT_THR_HIGH 0 /* High threshold exceeded */
+#define VCNL4010_INT_THR_LOW 1 /* Low threshold exceeded */
+#define VCNL4010_INT_ALS 2 /* ALS data ready */
+#define VCNL4010_INT_PROXIMITY 3 /* Proximity data ready */
+
+#define VCNL4010_INT_THR \
+ (BIT(VCNL4010_INT_THR_LOW) | BIT(VCNL4010_INT_THR_HIGH))
+#define VCNL4010_INT_DRDY \
+ (BIT(VCNL4010_INT_PROXIMITY) | BIT(VCNL4010_INT_ALS))
+
#define VCNL4000_SLEEP_DELAY_MS 2000 /* before we enter pm_runtime_suspend */
@@ -88,6 +117,10 @@ struct vcnl4000_data {
struct vcnl4000_chip_spec {
const char *prod;
+ struct iio_chan_spec const *channels;
+ const int num_channels;
+ const struct iio_info *info;
+ bool irq_support;
int (*init)(struct vcnl4000_data *data);
int (*measure_light)(struct vcnl4000_data *data, int *val);
int (*measure_proximity)(struct vcnl4000_data *data, int *val);
@@ -330,67 +363,16 @@ static int vcnl4200_measure_proximity(struct vcnl4000_data *data, int *val)
return vcnl4200_measure(data, &data->vcnl4200_ps, val);
}
-static const struct vcnl4000_chip_spec vcnl4000_chip_spec_cfg[] = {
- [VCNL4000] = {
- .prod = "VCNL4000",
- .init = vcnl4000_init,
- .measure_light = vcnl4000_measure_light,
- .measure_proximity = vcnl4000_measure_proximity,
- .set_power_state = vcnl4000_set_power_state,
- },
- [VCNL4010] = {
- .prod = "VCNL4010/4020",
- .init = vcnl4000_init,
- .measure_light = vcnl4000_measure_light,
- .measure_proximity = vcnl4000_measure_proximity,
- .set_power_state = vcnl4000_set_power_state,
- },
- [VCNL4040] = {
- .prod = "VCNL4040",
- .init = vcnl4200_init,
- .measure_light = vcnl4200_measure_light,
- .measure_proximity = vcnl4200_measure_proximity,
- .set_power_state = vcnl4200_set_power_state,
- },
- [VCNL4200] = {
- .prod = "VCNL4200",
- .init = vcnl4200_init,
- .measure_light = vcnl4200_measure_light,
- .measure_proximity = vcnl4200_measure_proximity,
- .set_power_state = vcnl4200_set_power_state,
- },
-};
-
-static ssize_t vcnl4000_read_near_level(struct iio_dev *indio_dev,
- uintptr_t priv,
- const struct iio_chan_spec *chan,
- char *buf)
+static bool vcnl4010_is_in_periodic_mode(struct vcnl4000_data *data)
{
- struct vcnl4000_data *data = iio_priv(indio_dev);
-
- return sprintf(buf, "%u\n", data->near_level);
-}
+ int ret;
-static const struct iio_chan_spec_ext_info vcnl4000_ext_info[] = {
- {
- .name = "nearlevel",
- .shared = IIO_SEPARATE,
- .read = vcnl4000_read_near_level,
- },
- { /* sentinel */ }
-};
+ ret = i2c_smbus_read_byte_data(data->client, VCNL4000_COMMAND);
+ if (ret < 0)
+ return false;
-static const struct iio_chan_spec vcnl4000_channels[] = {
- {
- .type = IIO_LIGHT,
- .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
- BIT(IIO_CHAN_INFO_SCALE),
- }, {
- .type = IIO_PROXIMITY,
- .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
- .ext_info = vcnl4000_ext_info,
- }
-};
+ return !!(ret & VCNL4000_SELF_TIMED_EN);
+}
static int vcnl4000_set_pm_runtime_state(struct vcnl4000_data *data, bool on)
{
@@ -450,10 +432,345 @@ static int vcnl4000_read_raw(struct iio_dev *indio_dev,
}
}
+static int vcnl4010_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ int ret;
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ case IIO_CHAN_INFO_SCALE:
+ ret = iio_device_claim_direct_mode(indio_dev);
+ if (ret)
+ return ret;
+
+ /* Protect against event capture. */
+ if (vcnl4010_is_in_periodic_mode(data)) {
+ ret = -EBUSY;
+ } else {
+ ret = vcnl4000_read_raw(indio_dev, chan, val, val2,
+ mask);
+ }
+
+ iio_device_release_direct_mode(indio_dev);
+ return ret;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int vcnl4010_read_event(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ enum iio_event_type type,
+ enum iio_event_direction dir,
+ enum iio_event_info info,
+ int *val, int *val2)
+{
+ int ret;
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+
+ switch (info) {
+ case IIO_EV_INFO_VALUE:
+ switch (dir) {
+ case IIO_EV_DIR_RISING:
+ ret = vcnl4000_read_data(data, VCNL4010_HIGH_THR_HI,
+ val);
+ if (ret < 0)
+ return ret;
+ return IIO_VAL_INT;
+ case IIO_EV_DIR_FALLING:
+ ret = vcnl4000_read_data(data, VCNL4010_LOW_THR_HI,
+ val);
+ if (ret < 0)
+ return ret;
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+ default:
+ return -EINVAL;
+ }
+}
+
+static int vcnl4010_write_event(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ enum iio_event_type type,
+ enum iio_event_direction dir,
+ enum iio_event_info info,
+ int val, int val2)
+{
+ int ret;
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+
+ switch (info) {
+ case IIO_EV_INFO_VALUE:
+ switch (dir) {
+ case IIO_EV_DIR_RISING:
+ ret = vcnl4000_write_data(data, VCNL4010_HIGH_THR_HI,
+ val);
+ if (ret < 0)
+ return ret;
+ return IIO_VAL_INT;
+ case IIO_EV_DIR_FALLING:
+ ret = vcnl4000_write_data(data, VCNL4010_LOW_THR_HI,
+ val);
+ if (ret < 0)
+ return ret;
+ return IIO_VAL_INT;
+ default:
+ return -EINVAL;
+ }
+ default:
+ return -EINVAL;
+ }
+}
+
+static bool vcnl4010_is_thr_enabled(struct vcnl4000_data *data)
+{
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(data->client, VCNL4010_INT_CTRL);
+ if (ret < 0)
+ return false;
+
+ return !!(ret & VCNL4010_INT_THR_EN);
+}
+
+static int vcnl4010_read_event_config(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ enum iio_event_type type,
+ enum iio_event_direction dir)
+{
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+
+ switch (chan->type) {
+ case IIO_PROXIMITY:
+ return vcnl4010_is_thr_enabled(data);
+ default:
+ return -EINVAL;
+ }
+}
+
+static int vcnl4010_config_threshold(struct iio_dev *indio_dev, bool state)
+{
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+ int ret;
+ int icr;
+ int command;
+
+ if (state) {
+ ret = iio_device_claim_direct_mode(indio_dev);
+ if (ret)
+ return ret;
+
+ /* Enable periodic measurement of proximity data. */
+ command = VCNL4000_SELF_TIMED_EN | VCNL4000_PROX_EN;
+
+ /*
+ * Enable interrupts on threshold, for proximity data by
+ * default.
+ */
+ icr = VCNL4010_INT_THR_EN;
+ } else {
+ if (!vcnl4010_is_thr_enabled(data))
+ return 0;
+
+ command = 0;
+ icr = 0;
+ }
+
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4000_COMMAND,
+ command);
+ if (ret < 0)
+ goto end;
+
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4010_INT_CTRL, icr);
+
+end:
+ if (state)
+ iio_device_release_direct_mode(indio_dev);
+
+ return ret;
+}
+
+static int vcnl4010_write_event_config(struct iio_dev *indio_dev,
+ const struct iio_chan_spec *chan,
+ enum iio_event_type type,
+ enum iio_event_direction dir,
+ int state)
+{
+ switch (chan->type) {
+ case IIO_PROXIMITY:
+ return vcnl4010_config_threshold(indio_dev, state);
+ default:
+ return -EINVAL;
+ }
+}
+
+static ssize_t vcnl4000_read_near_level(struct iio_dev *indio_dev,
+ uintptr_t priv,
+ const struct iio_chan_spec *chan,
+ char *buf)
+{
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+
+ return sprintf(buf, "%u\n", data->near_level);
+}
+
+static const struct iio_chan_spec_ext_info vcnl4000_ext_info[] = {
+ {
+ .name = "nearlevel",
+ .shared = IIO_SEPARATE,
+ .read = vcnl4000_read_near_level,
+ },
+ { /* sentinel */ }
+};
+
+static const struct iio_event_spec vcnl4000_event_spec[] = {
+ {
+ .type = IIO_EV_TYPE_THRESH,
+ .dir = IIO_EV_DIR_RISING,
+ .mask_separate = BIT(IIO_EV_INFO_VALUE),
+ }, {
+ .type = IIO_EV_TYPE_THRESH,
+ .dir = IIO_EV_DIR_FALLING,
+ .mask_separate = BIT(IIO_EV_INFO_VALUE),
+ }, {
+ .type = IIO_EV_TYPE_THRESH,
+ .dir = IIO_EV_DIR_EITHER,
+ .mask_separate = BIT(IIO_EV_INFO_ENABLE),
+ }
+};
+
+static const struct iio_chan_spec vcnl4000_channels[] = {
+ {
+ .type = IIO_LIGHT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ }, {
+ .type = IIO_PROXIMITY,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .ext_info = vcnl4000_ext_info,
+ }
+};
+
+static const struct iio_chan_spec vcnl4010_channels[] = {
+ {
+ .type = IIO_LIGHT,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ }, {
+ .type = IIO_PROXIMITY,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .event_spec = vcnl4000_event_spec,
+ .num_event_specs = ARRAY_SIZE(vcnl4000_event_spec),
+ .ext_info = vcnl4000_ext_info,
+ },
+};
+
static const struct iio_info vcnl4000_info = {
.read_raw = vcnl4000_read_raw,
};
+static const struct iio_info vcnl4010_info = {
+ .read_raw = vcnl4010_read_raw,
+ .read_event_value = vcnl4010_read_event,
+ .write_event_value = vcnl4010_write_event,
+ .read_event_config = vcnl4010_read_event_config,
+ .write_event_config = vcnl4010_write_event_config,
+};
+
+static const struct vcnl4000_chip_spec vcnl4000_chip_spec_cfg[] = {
+ [VCNL4000] = {
+ .prod = "VCNL4000",
+ .init = vcnl4000_init,
+ .measure_light = vcnl4000_measure_light,
+ .measure_proximity = vcnl4000_measure_proximity,
+ .set_power_state = vcnl4000_set_power_state,
+ .channels = vcnl4000_channels,
+ .num_channels = ARRAY_SIZE(vcnl4000_channels),
+ .info = &vcnl4000_info,
+ .irq_support = false,
+ },
+ [VCNL4010] = {
+ .prod = "VCNL4010/4020",
+ .init = vcnl4000_init,
+ .measure_light = vcnl4000_measure_light,
+ .measure_proximity = vcnl4000_measure_proximity,
+ .set_power_state = vcnl4000_set_power_state,
+ .channels = vcnl4010_channels,
+ .num_channels = ARRAY_SIZE(vcnl4010_channels),
+ .info = &vcnl4010_info,
+ .irq_support = true,
+ },
+ [VCNL4040] = {
+ .prod = "VCNL4040",
+ .init = vcnl4200_init,
+ .measure_light = vcnl4200_measure_light,
+ .measure_proximity = vcnl4200_measure_proximity,
+ .set_power_state = vcnl4200_set_power_state,
+ .channels = vcnl4000_channels,
+ .num_channels = ARRAY_SIZE(vcnl4000_channels),
+ .info = &vcnl4000_info,
+ .irq_support = false,
+ },
+ [VCNL4200] = {
+ .prod = "VCNL4200",
+ .init = vcnl4200_init,
+ .measure_light = vcnl4200_measure_light,
+ .measure_proximity = vcnl4200_measure_proximity,
+ .set_power_state = vcnl4200_set_power_state,
+ .channels = vcnl4000_channels,
+ .num_channels = ARRAY_SIZE(vcnl4000_channels),
+ .info = &vcnl4000_info,
+ .irq_support = false,
+ },
+};
+
+static irqreturn_t vcnl4010_irq_thread(int irq, void *p)
+{
+ struct iio_dev *indio_dev = p;
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+ unsigned long isr;
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(data->client, VCNL4010_ISR);
+ if (ret < 0)
+ goto end;
+
+ isr = ret;
+
+ if (isr & VCNL4010_INT_THR) {
+ if (test_bit(VCNL4010_INT_THR_LOW, &isr)) {
+ iio_push_event(indio_dev,
+ IIO_UNMOD_EVENT_CODE(
+ IIO_PROXIMITY,
+ 1,
+ IIO_EV_TYPE_THRESH,
+ IIO_EV_DIR_FALLING),
+ iio_get_time_ns(indio_dev));
+ }
+
+ if (test_bit(VCNL4010_INT_THR_HIGH, &isr)) {
+ iio_push_event(indio_dev,
+ IIO_UNMOD_EVENT_CODE(
+ IIO_PROXIMITY,
+ 1,
+ IIO_EV_TYPE_THRESH,
+ IIO_EV_DIR_RISING),
+ iio_get_time_ns(indio_dev));
+ }
+
+ i2c_smbus_write_byte_data(data->client, VCNL4010_ISR,
+ isr & VCNL4010_INT_THR);
+ }
+
+end:
+ return IRQ_HANDLED;
+}
+
static int vcnl4000_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -483,12 +800,25 @@ static int vcnl4000_probe(struct i2c_client *client,
data->near_level = 0;
indio_dev->dev.parent = &client->dev;
- indio_dev->info = &vcnl4000_info;
- indio_dev->channels = vcnl4000_channels;
- indio_dev->num_channels = ARRAY_SIZE(vcnl4000_channels);
+ indio_dev->info = data->chip_spec->info;
+ indio_dev->channels = data->chip_spec->channels;
+ indio_dev->num_channels = data->chip_spec->num_channels;
indio_dev->name = VCNL4000_DRV_NAME;
indio_dev->modes = INDIO_DIRECT_MODE;
+ if (client->irq && data->chip_spec->irq_support) {
+ ret = devm_request_threaded_irq(&client->dev, client->irq,
+ NULL, vcnl4010_irq_thread,
+ IRQF_TRIGGER_FALLING |
+ IRQF_ONESHOT,
+ "vcnl4010_irq",
+ indio_dev);
+ if (ret < 0) {
+ dev_err(&client->dev, "irq request failed\n");
+ return ret;
+ }
+ }
+
ret = pm_runtime_set_active(&client->dev);
if (ret < 0)
goto fail_poweroff;
--
2.26.0
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v6 4/5] iio: vcnl4000: Add sampling frequency support for VCNL4010/20.
2020-04-27 9:55 [PATCH v6 0/5] iio: vcnl: Add interrupts support for VCNL4010/20 Mathieu Othacehe
` (2 preceding siblings ...)
2020-04-27 9:55 ` [PATCH v6 3/5] iio: vcnl4000: Add event support for VCNL4010/20 Mathieu Othacehe
@ 2020-04-27 9:55 ` Mathieu Othacehe
2020-04-27 9:55 ` [PATCH v6 5/5] iio: vcnl4000: Add buffer " Mathieu Othacehe
4 siblings, 0 replies; 9+ messages in thread
From: Mathieu Othacehe @ 2020-04-27 9:55 UTC (permalink / raw)
To: jic23, knaack.h, lars, pmeerw; +Cc: linux-iio, linux-kernel, Mathieu Othacehe
Add sampling frequency support for proximity data on VCNL4010 and VCNL4020
chips.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
---
drivers/iio/light/vcnl4000.c | 118 ++++++++++++++++++++++++++++++++++-
1 file changed, 117 insertions(+), 1 deletion(-)
diff --git a/drivers/iio/light/vcnl4000.c b/drivers/iio/light/vcnl4000.c
index e7653037fa5d..65c0cf2b5037 100644
--- a/drivers/iio/light/vcnl4000.c
+++ b/drivers/iio/light/vcnl4000.c
@@ -86,6 +86,16 @@
#define VCNL4010_INT_DRDY \
(BIT(VCNL4010_INT_PROXIMITY) | BIT(VCNL4010_INT_ALS))
+static const int vcnl4010_prox_sampling_frequency[][2] = {
+ {1, 950000},
+ {3, 906250},
+ {7, 812500},
+ {16, 625000},
+ {31, 250000},
+ {62, 500000},
+ {125, 0},
+ {250, 0},
+};
#define VCNL4000_SLEEP_DELAY_MS 2000 /* before we enter pm_runtime_suspend */
@@ -363,6 +373,24 @@ static int vcnl4200_measure_proximity(struct vcnl4000_data *data, int *val)
return vcnl4200_measure(data, &data->vcnl4200_ps, val);
}
+static int vcnl4010_read_proxy_samp_freq(struct vcnl4000_data *data, int *val,
+ int *val2)
+{
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(data->client, VCNL4010_PROX_RATE);
+ if (ret < 0)
+ return ret;
+
+ if (ret >= ARRAY_SIZE(vcnl4010_prox_sampling_frequency))
+ return -EINVAL;
+
+ *val = vcnl4010_prox_sampling_frequency[ret][0];
+ *val2 = vcnl4010_prox_sampling_frequency[ret][1];
+
+ return 0;
+}
+
static bool vcnl4010_is_in_periodic_mode(struct vcnl4000_data *data)
{
int ret;
@@ -456,11 +484,95 @@ static int vcnl4010_read_raw(struct iio_dev *indio_dev,
iio_device_release_direct_mode(indio_dev);
return ret;
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ switch (chan->type) {
+ case IIO_PROXIMITY:
+ ret = vcnl4010_read_proxy_samp_freq(data, val, val2);
+ if (ret < 0)
+ return ret;
+ return IIO_VAL_INT_PLUS_MICRO;
+ default:
+ return -EINVAL;
+ }
default:
return -EINVAL;
}
}
+static int vcnl4010_read_avail(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ const int **vals, int *type, int *length,
+ long mask)
+{
+ switch (mask) {
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ *vals = (int *)vcnl4010_prox_sampling_frequency;
+ *type = IIO_VAL_INT_PLUS_MICRO;
+ *length = 2 * ARRAY_SIZE(vcnl4010_prox_sampling_frequency);
+ return IIO_AVAIL_LIST;
+ default:
+ return -EINVAL;
+ }
+}
+
+static int vcnl4010_write_proxy_samp_freq(struct vcnl4000_data *data, int val,
+ int val2)
+{
+ unsigned int i;
+ int index = -1;
+
+ for (i = 0; i < ARRAY_SIZE(vcnl4010_prox_sampling_frequency); i++) {
+ if (val == vcnl4010_prox_sampling_frequency[i][0] &&
+ val2 == vcnl4010_prox_sampling_frequency[i][1]) {
+ index = i;
+ break;
+ }
+ }
+
+ if (index < 0)
+ return -EINVAL;
+
+ return i2c_smbus_write_byte_data(data->client, VCNL4010_PROX_RATE,
+ index);
+}
+
+static int vcnl4010_write_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int val, int val2, long mask)
+{
+ int ret;
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+
+ ret = iio_device_claim_direct_mode(indio_dev);
+ if (ret)
+ return ret;
+
+ /* Protect against event capture. */
+ if (vcnl4010_is_in_periodic_mode(data)) {
+ ret = -EBUSY;
+ goto end;
+ }
+
+ switch (mask) {
+ case IIO_CHAN_INFO_SAMP_FREQ:
+ switch (chan->type) {
+ case IIO_PROXIMITY:
+ ret = vcnl4010_write_proxy_samp_freq(data, val, val2);
+ goto end;
+ default:
+ ret = -EINVAL;
+ goto end;
+ }
+ default:
+ ret = -EINVAL;
+ goto end;
+ }
+
+end:
+ iio_device_release_direct_mode(indio_dev);
+ return ret;
+}
+
static int vcnl4010_read_event(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
@@ -663,7 +775,9 @@ static const struct iio_chan_spec vcnl4010_channels[] = {
BIT(IIO_CHAN_INFO_SCALE),
}, {
.type = IIO_PROXIMITY,
- .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SAMP_FREQ),
+ .info_mask_separate_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
.event_spec = vcnl4000_event_spec,
.num_event_specs = ARRAY_SIZE(vcnl4000_event_spec),
.ext_info = vcnl4000_ext_info,
@@ -676,6 +790,8 @@ static const struct iio_info vcnl4000_info = {
static const struct iio_info vcnl4010_info = {
.read_raw = vcnl4010_read_raw,
+ .read_avail = vcnl4010_read_avail,
+ .write_raw = vcnl4010_write_raw,
.read_event_value = vcnl4010_read_event,
.write_event_value = vcnl4010_write_event,
.read_event_config = vcnl4010_read_event_config,
--
2.26.0
^ permalink raw reply related [flat|nested] 9+ messages in thread* [PATCH v6 5/5] iio: vcnl4000: Add buffer support for VCNL4010/20.
2020-04-27 9:55 [PATCH v6 0/5] iio: vcnl: Add interrupts support for VCNL4010/20 Mathieu Othacehe
` (3 preceding siblings ...)
2020-04-27 9:55 ` [PATCH v6 4/5] iio: vcnl4000: Add sampling frequency " Mathieu Othacehe
@ 2020-04-27 9:55 ` Mathieu Othacehe
2020-05-03 8:56 ` Jonathan Cameron
4 siblings, 1 reply; 9+ messages in thread
From: Mathieu Othacehe @ 2020-04-27 9:55 UTC (permalink / raw)
To: jic23, knaack.h, lars, pmeerw; +Cc: linux-iio, linux-kernel, Mathieu Othacehe
The VCNL4010 and VCNL4020 chips are able to raise interrupts on data ready.
Use it to provide triggered buffer support for proximity data.
Those two chips also provide ambient light data. However, they are sampled
at different rate than proximity data. As this is not handled by the IIO
framework for now, and the sample frequencies of ambient light data are
very low, do add buffer support for them.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
---
drivers/iio/light/Kconfig | 2 +
drivers/iio/light/vcnl4000.c | 161 ++++++++++++++++++++++++++++++++++-
2 files changed, 161 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/light/Kconfig b/drivers/iio/light/Kconfig
index 74970f18a93b..05f61b1e223a 100644
--- a/drivers/iio/light/Kconfig
+++ b/drivers/iio/light/Kconfig
@@ -506,6 +506,8 @@ config US5182D
config VCNL4000
tristate "VCNL4000/4010/4020/4200 combined ALS and proximity sensor"
+ select IIO_BUFFER
+ select IIO_TRIGGERED_BUFFER
depends on I2C
help
Say Y here if you want to build a driver for the Vishay VCNL4000,
diff --git a/drivers/iio/light/vcnl4000.c b/drivers/iio/light/vcnl4000.c
index 65c0cf2b5037..5f3cc422c371 100644
--- a/drivers/iio/light/vcnl4000.c
+++ b/drivers/iio/light/vcnl4000.c
@@ -5,6 +5,7 @@
*
* Copyright 2012 Peter Meerwald <pmeerw@pmeerw.net>
* Copyright 2019 Pursim SPC
+ * Copyright 2020 Mathieu Othacehe <m.othacehe@gmail.com>
*
* IIO driver for:
* VCNL4000/10/20 (7-bit I2C slave address 0x13)
@@ -13,8 +14,7 @@
*
* TODO:
* allow to adjust IR current
- * periodic ALS/proximity measurement (VCNL4010/20)
- * interrupts (VCNL4010/20/40, VCNL4200)
+ * interrupts (VCNL4040, VCNL4200)
*/
#include <linux/module.h>
@@ -24,9 +24,13 @@
#include <linux/pm_runtime.h>
#include <linux/interrupt.h>
+#include <linux/iio/buffer.h>
#include <linux/iio/events.h>
#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
#define VCNL4000_DRV_NAME "vcnl4000"
#define VCNL4000_PROD_ID 0x01
@@ -771,17 +775,26 @@ static const struct iio_chan_spec vcnl4000_channels[] = {
static const struct iio_chan_spec vcnl4010_channels[] = {
{
.type = IIO_LIGHT,
+ .scan_index = -1,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_SCALE),
}, {
.type = IIO_PROXIMITY,
+ .scan_index = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_SAMP_FREQ),
.info_mask_separate_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
.event_spec = vcnl4000_event_spec,
.num_event_specs = ARRAY_SIZE(vcnl4000_event_spec),
.ext_info = vcnl4000_ext_info,
+ .scan_type = {
+ .sign = 'u',
+ .realbits = 16,
+ .storagebits = 16,
+ .endianness = IIO_CPU,
+ },
},
+ IIO_CHAN_SOFT_TIMESTAMP(1),
};
static const struct iio_info vcnl4000_info = {
@@ -883,10 +896,139 @@ static irqreturn_t vcnl4010_irq_thread(int irq, void *p)
isr & VCNL4010_INT_THR);
}
+ if (isr & VCNL4010_INT_DRDY && iio_buffer_enabled(indio_dev))
+ iio_trigger_poll_chained(indio_dev->trig);
+
end:
return IRQ_HANDLED;
}
+static irqreturn_t vcnl4010_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *indio_dev = pf->indio_dev;
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+ const unsigned long *active_scan_mask = indio_dev->active_scan_mask;
+ u16 buffer[8] = {0}; /* 1x16-bit + ts */
+ bool data_read = false;
+ unsigned long isr;
+ int val = 0;
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(data->client, VCNL4010_ISR);
+ if (ret < 0)
+ goto end;
+
+ isr = ret;
+
+ if (test_bit(0, active_scan_mask)) {
+ if (test_bit(VCNL4010_INT_PROXIMITY, &isr)) {
+ ret = vcnl4000_read_data(data,
+ VCNL4000_PS_RESULT_HI,
+ &val);
+ if (ret < 0)
+ goto end;
+
+ buffer[0] = val;
+ data_read = true;
+ }
+ }
+
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4010_ISR,
+ isr & VCNL4010_INT_DRDY);
+ if (ret < 0)
+ goto end;
+
+ if (!data_read)
+ goto end;
+
+ iio_push_to_buffers_with_timestamp(indio_dev, buffer,
+ iio_get_time_ns(indio_dev));
+
+end:
+ iio_trigger_notify_done(indio_dev->trig);
+ return IRQ_HANDLED;
+}
+
+static int vcnl4010_buffer_postenable(struct iio_dev *indio_dev)
+{
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+ int ret;
+ int cmd;
+
+ ret = iio_triggered_buffer_postenable(indio_dev);
+ if (ret)
+ return ret;
+
+ /* Do not enable the buffer if we are already capturing events. */
+ if (vcnl4010_is_in_periodic_mode(data)) {
+ ret = -EBUSY;
+ goto end;
+ }
+
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4010_INT_CTRL,
+ VCNL4010_INT_PROX_EN);
+ if (ret < 0)
+ goto end;
+
+ cmd = VCNL4000_SELF_TIMED_EN | VCNL4000_PROX_EN;
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4000_COMMAND, cmd);
+ if (ret < 0)
+ goto end;
+
+end:
+ if (ret < 0)
+ iio_triggered_buffer_predisable(indio_dev);
+
+ return ret;
+}
+
+static int vcnl4010_buffer_predisable(struct iio_dev *indio_dev)
+{
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+ int ret, ret_disable;
+
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4010_INT_CTRL, 0);
+ if (ret < 0)
+ goto end;
+
+ ret = i2c_smbus_write_byte_data(data->client, VCNL4000_COMMAND, 0);
+
+end:
+ ret_disable = iio_triggered_buffer_predisable(indio_dev);
+ if (ret == 0)
+ ret = ret_disable;
+
+ return ret;
+}
+
+static const struct iio_buffer_setup_ops vcnl4010_buffer_ops = {
+ .postenable = &vcnl4010_buffer_postenable,
+ .predisable = &vcnl4010_buffer_predisable,
+};
+
+static const struct iio_trigger_ops vcnl4010_trigger_ops = {
+ .validate_device = iio_trigger_validate_own_device,
+};
+
+static int vcnl4010_probe_trigger(struct iio_dev *indio_dev)
+{
+ struct vcnl4000_data *data = iio_priv(indio_dev);
+ struct i2c_client *client = data->client;
+ struct iio_trigger *trigger;
+
+ trigger = devm_iio_trigger_alloc(&client->dev, "%s-dev%d",
+ indio_dev->name, indio_dev->id);
+ if (!trigger)
+ return -ENOMEM;
+
+ trigger->dev.parent = &client->dev;
+ trigger->ops = &vcnl4010_trigger_ops;
+ iio_trigger_set_drvdata(trigger, indio_dev);
+
+ return devm_iio_trigger_register(&client->dev, trigger);
+}
+
static int vcnl4000_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -923,6 +1065,16 @@ static int vcnl4000_probe(struct i2c_client *client,
indio_dev->modes = INDIO_DIRECT_MODE;
if (client->irq && data->chip_spec->irq_support) {
+ ret = devm_iio_triggered_buffer_setup(&client->dev, indio_dev,
+ NULL,
+ vcnl4010_trigger_handler,
+ &vcnl4010_buffer_ops);
+ if (ret < 0) {
+ dev_err(&client->dev,
+ "unable to setup iio triggered buffer\n");
+ return ret;
+ }
+
ret = devm_request_threaded_irq(&client->dev, client->irq,
NULL, vcnl4010_irq_thread,
IRQF_TRIGGER_FALLING |
@@ -933,6 +1085,10 @@ static int vcnl4000_probe(struct i2c_client *client,
dev_err(&client->dev, "irq request failed\n");
return ret;
}
+
+ ret = vcnl4010_probe_trigger(indio_dev);
+ if (ret < 0)
+ return ret;
}
ret = pm_runtime_set_active(&client->dev);
@@ -1028,5 +1184,6 @@ static struct i2c_driver vcnl4000_driver = {
module_i2c_driver(vcnl4000_driver);
MODULE_AUTHOR("Peter Meerwald <pmeerw@pmeerw.net>");
+MODULE_AUTHOR("Mathieu Othacehe <m.othacehe@gmail.com>");
MODULE_DESCRIPTION("Vishay VCNL4000 proximity/ambient light sensor driver");
MODULE_LICENSE("GPL");
--
2.26.0
^ permalink raw reply related [flat|nested] 9+ messages in thread