* [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS
@ 2020-05-01 13:43 Colin King
2020-05-01 18:00 ` AW: " Walter Harms
2020-05-02 12:21 ` Sergei Shtylyov
0 siblings, 2 replies; 4+ messages in thread
From: Colin King @ 2020-05-01 13:43 UTC (permalink / raw)
To: Vladimir Oltean, Andrew Lunn, Vivien Didelot, Florian Fainelli,
David S . Miller, Russell King, linux-kernel
Cc: kernel-janitors, netdev
From: Colin Ian King <colin.king@canonical.com>
The current logic for speed checking will never set the speed to 10 MBPS
because bmcr & BMCR_SPEED10 is always 0 since BMCR_SPEED10 is 0. Also
the erroneous setting where BMCR_SPEED1000 and BMCR_SPEED100 are both
set causes the speed to be 1000 MBS. Fix this by masking bps and checking
for just the expected settings of BMCR_SPEED1000, BMCR_SPEED100 and
BMCR_SPEED10 and defaulting to the unknown speed otherwise.
Addresses-Coverity: ("Logically dead code")
Fixes: ffe10e679cec ("net: dsa: sja1105: Add support for the SGMII port")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
---
drivers/net/dsa/sja1105/sja1105_main.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 472f4eb20c49..59a9038cdc4e 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -1600,6 +1600,7 @@ static const char * const sja1105_reset_reasons[] = {
int sja1105_static_config_reload(struct sja1105_private *priv,
enum sja1105_reset_reason reason)
{
+ const int mask = (BMCR_SPEED1000 | BMCR_SPEED100 | BMCR_SPEED10);
struct ptp_system_timestamp ptp_sts_before;
struct ptp_system_timestamp ptp_sts_after;
struct sja1105_mac_config_entry *mac;
@@ -1684,14 +1685,16 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
sja1105_sgmii_pcs_config(priv, an_enabled, false);
if (!an_enabled) {
- int speed = SPEED_UNKNOWN;
+ int speed;
- if (bmcr & BMCR_SPEED1000)
+ if ((bmcr & mask) == BMCR_SPEED1000)
speed = SPEED_1000;
- else if (bmcr & BMCR_SPEED100)
+ else if ((bmcr & mask) == BMCR_SPEED100)
speed = SPEED_100;
- else if (bmcr & BMCR_SPEED10)
+ else if ((bmcr & mask) == BMCR_SPEED10)
speed = SPEED_10;
+ else
+ speed = SPEED_UNKNOWN;
sja1105_sgmii_pcs_force_speed(priv, speed);
}
--
2.25.1
^ permalink raw reply related [flat|nested] 4+ messages in thread* AW: [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS
2020-05-01 13:43 [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS Colin King
@ 2020-05-01 18:00 ` Walter Harms
2020-05-01 18:37 ` Russell King - ARM Linux admin
2020-05-02 12:21 ` Sergei Shtylyov
1 sibling, 1 reply; 4+ messages in thread
From: Walter Harms @ 2020-05-01 18:00 UTC (permalink / raw)
To: Colin King, Vladimir Oltean, Andrew Lunn, Vivien Didelot,
Florian Fainelli, David S . Miller, Russell King, linux-kernel
Cc: kernel-janitors, netdev
IMHO it would be better to use switch case here to improve readability.
switch (bmcr & mask) {
case BMCR_SPEED1000:
speed = SPEED_1000;
break;
case BMCR_SPEED100:
speed = SPEED_100;
break;
case BMCR_SPEED10:
speed = SPEED_10;
break;
default:
speed = SPEED_UNKNOWN
}
jm2c,
wh
btw: an_enabled ? why not !enabled, mich more easy to read
________________________________________
Von: kernel-janitors-owner@vger.kernel.org <kernel-janitors-owner@vger.kernel.org> im Auftrag von Colin King <colin.king@canonical.com>
Gesendet: Freitag, 1. Mai 2020 15:43:10
An: Vladimir Oltean; Andrew Lunn; Vivien Didelot; Florian Fainelli; David S . Miller; Russell King; linux-kernel@vger.kernel.org
Cc: kernel-janitors@vger.kernel.org; netdev@vger.kernel.org
Betreff: [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS
From: Colin Ian King <colin.king@canonical.com>
The current logic for speed checking will never set the speed to 10 MBPS
because bmcr & BMCR_SPEED10 is always 0 since BMCR_SPEED10 is 0. Also
the erroneous setting where BMCR_SPEED1000 and BMCR_SPEED100 are both
set causes the speed to be 1000 MBS. Fix this by masking bps and checking
for just the expected settings of BMCR_SPEED1000, BMCR_SPEED100 and
BMCR_SPEED10 and defaulting to the unknown speed otherwise.
Addresses-Coverity: ("Logically dead code")
Fixes: ffe10e679cec ("net: dsa: sja1105: Add support for the SGMII port")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
---
drivers/net/dsa/sja1105/sja1105_main.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 472f4eb20c49..59a9038cdc4e 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -1600,6 +1600,7 @@ static const char * const sja1105_reset_reasons[] = {
int sja1105_static_config_reload(struct sja1105_private *priv,
enum sja1105_reset_reason reason)
{
+ const int mask = (BMCR_SPEED1000 | BMCR_SPEED100 | BMCR_SPEED10);
struct ptp_system_timestamp ptp_sts_before;
struct ptp_system_timestamp ptp_sts_after;
struct sja1105_mac_config_entry *mac;
@@ -1684,14 +1685,16 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
sja1105_sgmii_pcs_config(priv, an_enabled, false);
if (!an_enabled) {
- int speed = SPEED_UNKNOWN;
+ int speed;
- if (bmcr & BMCR_SPEED1000)
+ if ((bmcr & mask) == BMCR_SPEED1000)
speed = SPEED_1000;
- else if (bmcr & BMCR_SPEED100)
+ else if ((bmcr & mask) == BMCR_SPEED100)
speed = SPEED_100;
- else if (bmcr & BMCR_SPEED10)
+ else if ((bmcr & mask) == BMCR_SPEED10)
speed = SPEED_10;
+ else
+ speed = SPEED_UNKNOWN;
sja1105_sgmii_pcs_force_speed(priv, speed);
}
--
2.25.1
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS
2020-05-01 18:00 ` AW: " Walter Harms
@ 2020-05-01 18:37 ` Russell King - ARM Linux admin
0 siblings, 0 replies; 4+ messages in thread
From: Russell King - ARM Linux admin @ 2020-05-01 18:37 UTC (permalink / raw)
To: Walter Harms
Cc: Colin King, Vladimir Oltean, Andrew Lunn, Vivien Didelot,
Florian Fainelli, David S . Miller, linux-kernel,
kernel-janitors, netdev
On Fri, May 01, 2020 at 06:00:52PM +0000, Walter Harms wrote:
> IMHO it would be better to use switch case here to improve readability.
>
> switch (bmcr & mask) {
>
> case BMCR_SPEED1000:
> speed = SPEED_1000;
> break;
> case BMCR_SPEED100:
> speed = SPEED_100;
> break;
> case BMCR_SPEED10:
> speed = SPEED_10;
> break;
> default:
> speed = SPEED_UNKNOWN
> }
>
> jm2c,
> wh
>
> btw: an_enabled ? why not !enabled, mich more easy to read
You misinterpret "an_enabled". It's not "negated enabled". It's not
even "disabled". It's short for "autonegotiation enabled". It's
positive logic too.
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 10.2Mbps down 587kbps up
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS
2020-05-01 13:43 [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS Colin King
2020-05-01 18:00 ` AW: " Walter Harms
@ 2020-05-02 12:21 ` Sergei Shtylyov
1 sibling, 0 replies; 4+ messages in thread
From: Sergei Shtylyov @ 2020-05-02 12:21 UTC (permalink / raw)
To: Colin King, Vladimir Oltean, Andrew Lunn, Vivien Didelot,
Florian Fainelli, David S . Miller, Russell King, linux-kernel
Cc: kernel-janitors, netdev
Hello!
On 01.05.2020 16:43, Colin King wrote:
> From: Colin Ian King <colin.king@canonical.com>
>
> The current logic for speed checking will never set the speed to 10 MBPS
> because bmcr & BMCR_SPEED10 is always 0 since BMCR_SPEED10 is 0. Also
> the erroneous setting where BMCR_SPEED1000 and BMCR_SPEED100 are both
> set causes the speed to be 1000 MBS. Fix this by masking bps and checking
> for just the expected settings of BMCR_SPEED1000, BMCR_SPEED100 and
> BMCR_SPEED10 and defaulting to the unknown speed otherwise.
>
> Addresses-Coverity: ("Logically dead code")
> Fixes: ffe10e679cec ("net: dsa: sja1105: Add support for the SGMII port")
> Signed-off-by: Colin Ian King <colin.king@canonical.com>
> ---
> drivers/net/dsa/sja1105/sja1105_main.c | 11 +++++++----
> 1 file changed, 7 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
> index 472f4eb20c49..59a9038cdc4e 100644
> --- a/drivers/net/dsa/sja1105/sja1105_main.c
> +++ b/drivers/net/dsa/sja1105/sja1105_main.c
> @@ -1600,6 +1600,7 @@ static const char * const sja1105_reset_reasons[] = {
> int sja1105_static_config_reload(struct sja1105_private *priv,
> enum sja1105_reset_reason reason)
> {
> + const int mask = (BMCR_SPEED1000 | BMCR_SPEED100 | BMCR_SPEED10);
Why not declare it in the block it's used in? Also, () not needed here.
> struct ptp_system_timestamp ptp_sts_before;
> struct ptp_system_timestamp ptp_sts_after;
> struct sja1105_mac_config_entry *mac;
> @@ -1684,14 +1685,16 @@ int sja1105_static_config_reload(struct sja1105_private *priv,
> sja1105_sgmii_pcs_config(priv, an_enabled, false);
>
> if (!an_enabled) {
> - int speed = SPEED_UNKNOWN;
> + int speed;
Why not the following?
int mask = bmcr & (BMCR_SPEED1000 | BMCR_SPEED100 |
BMCR_SPEED10);
>
> - if (bmcr & BMCR_SPEED1000)
> + if ((bmcr & mask) == BMCR_SPEED1000)
> speed = SPEED_1000;
> - else if (bmcr & BMCR_SPEED100)
> + else if ((bmcr & mask) == BMCR_SPEED100)
> speed = SPEED_100;
> - else if (bmcr & BMCR_SPEED10)
> + else if ((bmcr & mask) == BMCR_SPEED10)
> speed = SPEED_10;
> + else
> + speed = SPEED_UNKNOWN;
>
> sja1105_sgmii_pcs_force_speed(priv, speed);
> }
MBR, Sergei
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-05-02 12:21 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-01 13:43 [PATCH] net: dsa: sja1105: fix speed setting for 10 MBPS Colin King
2020-05-01 18:00 ` AW: " Walter Harms
2020-05-01 18:37 ` Russell King - ARM Linux admin
2020-05-02 12:21 ` Sergei Shtylyov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).