From: Sascha Hauer <s.hauer@pengutronix.de>
To: Robin Gong <yibin.gong@nxp.com>
Cc: vkoul@kernel.org, shawnguo@kernel.org,
u.kleine-koenig@pengutronix.de, robh+dt@kernel.org,
festevam@gmail.com, dan.j.williams@intel.com,
mark.rutland@arm.com, catalin.marinas@arm.com,
will.deacon@arm.com, l.stach@pengutronix.de,
martin.fuzzey@flowbird.group, kernel@pengutronix.de,
linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-imx@nxp.com,
dmaengine@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH v7 RESEND 07/13] spi: imx: fix ERR009165
Date: Wed, 13 May 2020 09:21:32 +0200 [thread overview]
Message-ID: <20200513072132.GL5877@pengutronix.de> (raw)
In-Reply-To: <1589218356-17475-8-git-send-email-yibin.gong@nxp.com>
On Tue, May 12, 2020 at 01:32:30AM +0800, Robin Gong wrote:
> Change to XCH mode even in dma mode, please refer to the below
> errata:
> https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch is the one bisecting will end up with when somebody uses an
older SDMA firmware or the ROM scripts. It should have a better
description what happens and what should be done about it.
Sascha
>
> Signed-off-by: Robin Gong <yibin.gong@nxp.com>
> Acked-by: Mark Brown <broonie@kernel.org>
> ---
> drivers/spi/spi-imx.c | 16 ++++++++--------
> 1 file changed, 8 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
> index f4f28a4..70df8e6 100644
> --- a/drivers/spi/spi-imx.c
> +++ b/drivers/spi/spi-imx.c
> @@ -585,8 +585,8 @@ static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
> ctrl |= mx51_ecspi_clkdiv(spi_imx, t->speed_hz, &clk);
> spi_imx->spi_bus_clk = clk;
>
> - if (spi_imx->usedma)
> - ctrl |= MX51_ECSPI_CTRL_SMC;
> + /* ERR009165: work in XHC mode as PIO */
> + ctrl &= ~MX51_ECSPI_CTRL_SMC;
>
> writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
>
> @@ -617,7 +617,7 @@ static void mx51_setup_wml(struct spi_imx_data *spi_imx)
> * and enable DMA request.
> */
> writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
> - MX51_ECSPI_DMA_TX_WML(spi_imx->wml) |
> + MX51_ECSPI_DMA_TX_WML(0) |
> MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
> MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
> MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
> @@ -1171,7 +1171,11 @@ static int spi_imx_dma_configure(struct spi_master *master)
> tx.direction = DMA_MEM_TO_DEV;
> tx.dst_addr = spi_imx->base_phys + MXC_CSPITXDATA;
> tx.dst_addr_width = buswidth;
> - tx.dst_maxburst = spi_imx->wml;
> + /*
> + * For ERR009165 with tx_wml = 0 could enlarge burst size to fifo size
> + * to speed up fifo filling as possible.
> + */
> + tx.dst_maxburst = spi_imx->devtype_data->fifo_size;
> ret = dmaengine_slave_config(master->dma_tx, &tx);
> if (ret) {
> dev_err(spi_imx->dev, "TX dma configuration failed with %d\n", ret);
> @@ -1265,10 +1269,6 @@ static int spi_imx_sdma_init(struct device *dev, struct spi_imx_data *spi_imx,
> {
> int ret;
>
> - /* use pio mode for i.mx6dl chip TKT238285 */
> - if (of_machine_is_compatible("fsl,imx6dl"))
> - return 0;
> -
> spi_imx->wml = spi_imx->devtype_data->fifo_size / 2;
>
> /* Prepare for TX DMA: */
> --
> 2.7.4
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2020-05-13 7:21 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-11 17:32 [PATCH v7 RESEND 00/13] add ecspi ERR009165 for i.mx6/7 soc family Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 01/13] Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core" Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 02/13] Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores" Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 03/13] Revert "dmaengine: imx-sdma: fix context cache" Robin Gong
2020-05-13 6:05 ` Sascha Hauer
2020-05-13 7:12 ` Fuzzey, Martin
2020-05-13 8:06 ` Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 04/13] Revert "dmaengine: imx-sdma: refine to load context only once" Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 05/13] dmaengine: imx-sdma: remove dupilicated sdma_load_context Robin Gong
2020-05-13 6:05 ` Sascha Hauer
2020-05-13 8:04 ` Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 06/13] dmaengine: imx-sdma: add mcu_2_ecspi script Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 07/13] spi: imx: fix ERR009165 Robin Gong
2020-05-13 7:21 ` Sascha Hauer [this message]
2020-05-13 8:38 ` Robin Gong
2020-05-13 8:48 ` Sascha Hauer
2020-05-13 8:52 ` Robin Gong
2020-05-13 9:20 ` Sascha Hauer
2020-05-13 15:48 ` Robin Gong
2020-05-13 7:33 ` Sascha Hauer
2020-05-13 9:05 ` Robin Gong
2020-05-13 9:20 ` Sascha Hauer
2020-05-13 9:36 ` Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 08/13] spi: imx: remove ERR009165 workaround on i.mx6ul Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 09/13] spi: imx: add new i.mx6ul compatible name in binding doc Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 10/13] dmaengine: imx-sdma: remove ERR009165 on i.mx6ul Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 11/13] dma: imx-sdma: add i.mx6ul compatible name Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 12/13] dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm Robin Gong
2020-05-11 17:32 ` [PATCH v7 RESEND 13/13] dmaengine: imx-sdma: add uart rom script Robin Gong
2020-05-13 21:06 ` Fabio Estevam
2020-05-14 1:45 ` Robin Gong
2020-05-13 7:20 ` [PATCH v7 RESEND 00/13] add ecspi ERR009165 for i.mx6/7 soc family Sascha Hauer
2020-05-13 8:20 ` Robin Gong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200513072132.GL5877@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=catalin.marinas@arm.com \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=l.stach@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=martin.fuzzey@flowbird.group \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=u.kleine-koenig@pengutronix.de \
--cc=vkoul@kernel.org \
--cc=will.deacon@arm.com \
--cc=yibin.gong@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).