* [PATCH net-next 0/4] net: phy: broadcom: cable tester support
@ 2020-05-13 16:35 Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 1/4] net: phy: broadcom: add exp register access methods without buslock Michael Walle
` (4 more replies)
0 siblings, 5 replies; 6+ messages in thread
From: Michael Walle @ 2020-05-13 16:35 UTC (permalink / raw)
To: netdev, linux-kernel
Cc: Andrew Lunn, Florian Fainelli, Heiner Kallweit, Russell King,
David S . Miller, Michael Walle
Add cable tester support for the Broadcom PHYs. Support for it was
developed on a BCM54140 Quad PHY which RDB register access.
If there is a link partner the results are not as good as with an open
cable. I guess we could retry if the measurement until all pairs had at
least one valid result.
changes since v1:
- added Reviewed-by: tags
- removed "div by 2" for cross shorts, just mention it in the commit
message. The results are inconclusive if the tests are repeated. So
just report the length as is for now.
- fixed typo in commit message
Michael Walle (4):
net: phy: broadcom: add exp register access methods without buslock
net: phy: broadcom: add bcm_phy_modify_exp()
net: phy: broadcom: add cable test support
net: phy: bcm54140: add cable diagnostics support
drivers/net/phy/bcm-phy-lib.c | 259 +++++++++++++++++++++++++++++++++-
drivers/net/phy/bcm-phy-lib.h | 10 ++
drivers/net/phy/bcm54140.c | 3 +
include/linux/brcmphy.h | 52 +++++++
4 files changed, 317 insertions(+), 7 deletions(-)
--
2.20.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH net-next v2 1/4] net: phy: broadcom: add exp register access methods without buslock
2020-05-13 16:35 [PATCH net-next 0/4] net: phy: broadcom: cable tester support Michael Walle
@ 2020-05-13 16:35 ` Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 2/4] net: phy: broadcom: add bcm_phy_modify_exp() Michael Walle
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Michael Walle @ 2020-05-13 16:35 UTC (permalink / raw)
To: netdev, linux-kernel
Cc: Andrew Lunn, Florian Fainelli, Heiner Kallweit, Russell King,
David S . Miller, Michael Walle
Add helper to read and write expansion registers without taking the mdio
lock.
Please note, that this changes the semantics of the read and write.
Before there was no lock between selecting the expansion register and
the actual read/write. This may lead to access failures if there are
parallel accesses. Instead take the bus lock during the whole access
cycle.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/bcm-phy-lib.c | 38 ++++++++++++++++++++++++++++-------
drivers/net/phy/bcm-phy-lib.h | 2 ++
2 files changed, 33 insertions(+), 7 deletions(-)
diff --git a/drivers/net/phy/bcm-phy-lib.c b/drivers/net/phy/bcm-phy-lib.c
index d5f9a2701989..a390812714ed 100644
--- a/drivers/net/phy/bcm-phy-lib.c
+++ b/drivers/net/phy/bcm-phy-lib.c
@@ -14,33 +14,57 @@
#define MII_BCM_CHANNEL_WIDTH 0x2000
#define BCM_CL45VEN_EEE_ADV 0x3c
-int bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val)
+int __bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val)
{
int rc;
- rc = phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
+ rc = __phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
if (rc < 0)
return rc;
- return phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
+ return __phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
+}
+EXPORT_SYMBOL_GPL(__bcm_phy_write_exp);
+
+int bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val)
+{
+ int rc;
+
+ phy_lock_mdio_bus(phydev);
+ rc = __bcm_phy_write_exp(phydev, reg, val);
+ phy_unlock_mdio_bus(phydev);
+
+ return rc;
}
EXPORT_SYMBOL_GPL(bcm_phy_write_exp);
-int bcm_phy_read_exp(struct phy_device *phydev, u16 reg)
+int __bcm_phy_read_exp(struct phy_device *phydev, u16 reg)
{
int val;
- val = phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
+ val = __phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
if (val < 0)
return val;
- val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
+ val = __phy_read(phydev, MII_BCM54XX_EXP_DATA);
/* Restore default value. It's O.K. if this write fails. */
- phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
+ __phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
return val;
}
+EXPORT_SYMBOL_GPL(__bcm_phy_read_exp);
+
+int bcm_phy_read_exp(struct phy_device *phydev, u16 reg)
+{
+ int rc;
+
+ phy_lock_mdio_bus(phydev);
+ rc = __bcm_phy_read_exp(phydev, reg);
+ phy_unlock_mdio_bus(phydev);
+
+ return rc;
+}
EXPORT_SYMBOL_GPL(bcm_phy_read_exp);
int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
diff --git a/drivers/net/phy/bcm-phy-lib.h b/drivers/net/phy/bcm-phy-lib.h
index 4d3de91cda6c..0eb5333cda39 100644
--- a/drivers/net/phy/bcm-phy-lib.h
+++ b/drivers/net/phy/bcm-phy-lib.h
@@ -27,6 +27,8 @@
#define AFE_HPF_TRIM_OTHERS MISC_ADDR(0x3a, 0)
+int __bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val);
+int __bcm_phy_read_exp(struct phy_device *phydev, u16 reg);
int bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val);
int bcm_phy_read_exp(struct phy_device *phydev, u16 reg);
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH net-next v2 2/4] net: phy: broadcom: add bcm_phy_modify_exp()
2020-05-13 16:35 [PATCH net-next 0/4] net: phy: broadcom: cable tester support Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 1/4] net: phy: broadcom: add exp register access methods without buslock Michael Walle
@ 2020-05-13 16:35 ` Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 3/4] net: phy: broadcom: add cable test support Michael Walle
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Michael Walle @ 2020-05-13 16:35 UTC (permalink / raw)
To: netdev, linux-kernel
Cc: Andrew Lunn, Florian Fainelli, Heiner Kallweit, Russell King,
David S . Miller, Michael Walle
Add the convenience function to do a read-modify-write. This has the
additional benefit of saving one write to the selection register.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/bcm-phy-lib.c | 32 ++++++++++++++++++++++++++++++++
drivers/net/phy/bcm-phy-lib.h | 2 ++
2 files changed, 34 insertions(+)
diff --git a/drivers/net/phy/bcm-phy-lib.c b/drivers/net/phy/bcm-phy-lib.c
index a390812714ed..41c728fbcfb2 100644
--- a/drivers/net/phy/bcm-phy-lib.c
+++ b/drivers/net/phy/bcm-phy-lib.c
@@ -67,6 +67,38 @@ int bcm_phy_read_exp(struct phy_device *phydev, u16 reg)
}
EXPORT_SYMBOL_GPL(bcm_phy_read_exp);
+int __bcm_phy_modify_exp(struct phy_device *phydev, u16 reg, u16 mask, u16 set)
+{
+ int new, ret;
+
+ ret = __phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
+ if (ret < 0)
+ return ret;
+
+ ret = __phy_read(phydev, MII_BCM54XX_EXP_DATA);
+ if (ret < 0)
+ return ret;
+
+ new = (ret & ~mask) | set;
+ if (new == ret)
+ return 0;
+
+ return __phy_write(phydev, MII_BCM54XX_EXP_DATA, new);
+}
+EXPORT_SYMBOL_GPL(__bcm_phy_modify_exp);
+
+int bcm_phy_modify_exp(struct phy_device *phydev, u16 reg, u16 mask, u16 set)
+{
+ int ret;
+
+ phy_lock_mdio_bus(phydev);
+ ret = __bcm_phy_modify_exp(phydev, reg, mask, set);
+ phy_unlock_mdio_bus(phydev);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(bcm_phy_modify_exp);
+
int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
{
/* The register must be written to both the Shadow Register Select and
diff --git a/drivers/net/phy/bcm-phy-lib.h b/drivers/net/phy/bcm-phy-lib.h
index 0eb5333cda39..b35d880220b9 100644
--- a/drivers/net/phy/bcm-phy-lib.h
+++ b/drivers/net/phy/bcm-phy-lib.h
@@ -29,8 +29,10 @@
int __bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val);
int __bcm_phy_read_exp(struct phy_device *phydev, u16 reg);
+int __bcm_phy_modify_exp(struct phy_device *phydev, u16 reg, u16 mask, u16 set);
int bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val);
int bcm_phy_read_exp(struct phy_device *phydev, u16 reg);
+int bcm_phy_modify_exp(struct phy_device *phydev, u16 reg, u16 mask, u16 set);
static inline int bcm_phy_write_exp_sel(struct phy_device *phydev,
u16 reg, u16 val)
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH net-next v2 3/4] net: phy: broadcom: add cable test support
2020-05-13 16:35 [PATCH net-next 0/4] net: phy: broadcom: cable tester support Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 1/4] net: phy: broadcom: add exp register access methods without buslock Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 2/4] net: phy: broadcom: add bcm_phy_modify_exp() Michael Walle
@ 2020-05-13 16:35 ` Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 4/4] net: phy: bcm54140: add cable diagnostics support Michael Walle
2020-05-13 19:52 ` [PATCH net-next 0/4] net: phy: broadcom: cable tester support David Miller
4 siblings, 0 replies; 6+ messages in thread
From: Michael Walle @ 2020-05-13 16:35 UTC (permalink / raw)
To: netdev, linux-kernel
Cc: Andrew Lunn, Florian Fainelli, Heiner Kallweit, Russell King,
David S . Miller, Michael Walle
Most modern broadcom PHYs support ECD (enhanced cable diagnostics). Add
support for it in the bcm-phy-lib so they can easily be used in the PHY
driver.
There are two access methods for ECD: legacy by expansion registers and
via the new RDB registers which are exclusive. Provide functions in two
variants where the PHY driver can choose from. To keep things simple for
now, we just switch the register access to expansion registers in the
RDB variant for now. On the flipside, we have to keep a bus lock to
prevent any other non-legacy access on the PHY.
The results of the intra-pair tests are inconclusive (at least for the
BCM54140). Most of the times half the length is reported but sometimes
the length is correct.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/bcm-phy-lib.c | 189 ++++++++++++++++++++++++++++++++++
drivers/net/phy/bcm-phy-lib.h | 6 ++
include/linux/brcmphy.h | 52 ++++++++++
3 files changed, 247 insertions(+)
diff --git a/drivers/net/phy/bcm-phy-lib.c b/drivers/net/phy/bcm-phy-lib.c
index 41c728fbcfb2..cb92786e3ded 100644
--- a/drivers/net/phy/bcm-phy-lib.c
+++ b/drivers/net/phy/bcm-phy-lib.c
@@ -4,12 +4,14 @@
*/
#include "bcm-phy-lib.h"
+#include <linux/bitfield.h>
#include <linux/brcmphy.h>
#include <linux/export.h>
#include <linux/mdio.h>
#include <linux/module.h>
#include <linux/phy.h>
#include <linux/ethtool.h>
+#include <linux/ethtool_netlink.h>
#define MII_BCM_CHANNEL_WIDTH 0x2000
#define BCM_CL45VEN_EEE_ADV 0x3c
@@ -581,6 +583,193 @@ int bcm_phy_enable_jumbo(struct phy_device *phydev)
}
EXPORT_SYMBOL_GPL(bcm_phy_enable_jumbo);
+int __bcm_phy_enable_rdb_access(struct phy_device *phydev)
+{
+ return __bcm_phy_write_exp(phydev, BCM54XX_EXP_REG7E, 0);
+}
+EXPORT_SYMBOL_GPL(__bcm_phy_enable_rdb_access);
+
+int __bcm_phy_enable_legacy_access(struct phy_device *phydev)
+{
+ return __bcm_phy_write_rdb(phydev, BCM54XX_RDB_REG0087,
+ BCM54XX_ACCESS_MODE_LEGACY_EN);
+}
+EXPORT_SYMBOL_GPL(__bcm_phy_enable_legacy_access);
+
+static int _bcm_phy_cable_test_start(struct phy_device *phydev, bool is_rdb)
+{
+ u16 mask, set;
+ int ret;
+
+ /* Auto-negotiation must be enabled for cable diagnostics to work, but
+ * don't advertise any capabilities.
+ */
+ phy_write(phydev, MII_BMCR, BMCR_ANENABLE);
+ phy_write(phydev, MII_ADVERTISE, ADVERTISE_CSMA);
+ phy_write(phydev, MII_CTRL1000, 0);
+
+ phy_lock_mdio_bus(phydev);
+ if (is_rdb) {
+ ret = __bcm_phy_enable_legacy_access(phydev);
+ if (ret)
+ goto out;
+ }
+
+ mask = BCM54XX_ECD_CTRL_CROSS_SHORT_DIS | BCM54XX_ECD_CTRL_UNIT_MASK;
+ set = BCM54XX_ECD_CTRL_RUN | BCM54XX_ECD_CTRL_BREAK_LINK |
+ FIELD_PREP(BCM54XX_ECD_CTRL_UNIT_MASK,
+ BCM54XX_ECD_CTRL_UNIT_CM);
+
+ ret = __bcm_phy_modify_exp(phydev, BCM54XX_EXP_ECD_CTRL, mask, set);
+
+out:
+ /* re-enable the RDB access even if there was an error */
+ if (is_rdb)
+ ret = __bcm_phy_enable_rdb_access(phydev) ? : ret;
+
+ phy_unlock_mdio_bus(phydev);
+
+ return ret;
+}
+
+static int bcm_phy_cable_test_report_trans(int result)
+{
+ switch (result) {
+ case BCM54XX_ECD_FAULT_TYPE_OK:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+ case BCM54XX_ECD_FAULT_TYPE_OPEN:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+ case BCM54XX_ECD_FAULT_TYPE_SAME_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+ case BCM54XX_ECD_FAULT_TYPE_CROSS_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+ case BCM54XX_ECD_FAULT_TYPE_INVALID:
+ case BCM54XX_ECD_FAULT_TYPE_BUSY:
+ default:
+ return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+ }
+}
+
+static bool bcm_phy_distance_valid(int result)
+{
+ switch (result) {
+ case BCM54XX_ECD_FAULT_TYPE_OPEN:
+ case BCM54XX_ECD_FAULT_TYPE_SAME_SHORT:
+ case BCM54XX_ECD_FAULT_TYPE_CROSS_SHORT:
+ return true;
+ }
+ return false;
+}
+
+static int bcm_phy_report_length(struct phy_device *phydev, int pair)
+{
+ int val;
+
+ val = __bcm_phy_read_exp(phydev,
+ BCM54XX_EXP_ECD_PAIR_A_LENGTH_RESULTS + pair);
+ if (val < 0)
+ return val;
+
+ if (val == BCM54XX_ECD_LENGTH_RESULTS_INVALID)
+ return 0;
+
+ ethnl_cable_test_fault_length(phydev, pair, val);
+
+ return 0;
+}
+
+static int _bcm_phy_cable_test_get_status(struct phy_device *phydev,
+ bool *finished, bool is_rdb)
+{
+ int pair_a, pair_b, pair_c, pair_d, ret;
+
+ *finished = false;
+
+ phy_lock_mdio_bus(phydev);
+
+ if (is_rdb) {
+ ret = __bcm_phy_enable_legacy_access(phydev);
+ if (ret)
+ goto out;
+ }
+
+ ret = __bcm_phy_read_exp(phydev, BCM54XX_EXP_ECD_CTRL);
+ if (ret < 0)
+ goto out;
+
+ if (ret & BCM54XX_ECD_CTRL_IN_PROGRESS) {
+ ret = 0;
+ goto out;
+ }
+
+ ret = __bcm_phy_read_exp(phydev, BCM54XX_EXP_ECD_FAULT_TYPE);
+ if (ret < 0)
+ goto out;
+
+ pair_a = FIELD_GET(BCM54XX_ECD_FAULT_TYPE_PAIR_A_MASK, ret);
+ pair_b = FIELD_GET(BCM54XX_ECD_FAULT_TYPE_PAIR_B_MASK, ret);
+ pair_c = FIELD_GET(BCM54XX_ECD_FAULT_TYPE_PAIR_C_MASK, ret);
+ pair_d = FIELD_GET(BCM54XX_ECD_FAULT_TYPE_PAIR_D_MASK, ret);
+
+ ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+ bcm_phy_cable_test_report_trans(pair_a));
+ ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_B,
+ bcm_phy_cable_test_report_trans(pair_b));
+ ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_C,
+ bcm_phy_cable_test_report_trans(pair_c));
+ ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_D,
+ bcm_phy_cable_test_report_trans(pair_d));
+
+ if (bcm_phy_distance_valid(pair_a))
+ bcm_phy_report_length(phydev, 0);
+ if (bcm_phy_distance_valid(pair_b))
+ bcm_phy_report_length(phydev, 1);
+ if (bcm_phy_distance_valid(pair_c))
+ bcm_phy_report_length(phydev, 2);
+ if (bcm_phy_distance_valid(pair_d))
+ bcm_phy_report_length(phydev, 3);
+
+ ret = 0;
+ *finished = true;
+out:
+ /* re-enable the RDB access even if there was an error */
+ if (is_rdb)
+ ret = __bcm_phy_enable_rdb_access(phydev) ? : ret;
+
+ phy_unlock_mdio_bus(phydev);
+
+ return ret;
+}
+
+int bcm_phy_cable_test_start(struct phy_device *phydev)
+{
+ return _bcm_phy_cable_test_start(phydev, false);
+}
+EXPORT_SYMBOL_GPL(bcm_phy_cable_test_start);
+
+int bcm_phy_cable_test_get_status(struct phy_device *phydev, bool *finished)
+{
+ return _bcm_phy_cable_test_get_status(phydev, finished, false);
+}
+EXPORT_SYMBOL_GPL(bcm_phy_cable_test_get_status);
+
+/* We assume that all PHYs which support RDB access can be switched to legacy
+ * mode. If, in the future, this is not true anymore, we have to re-implement
+ * this with RDB access.
+ */
+int bcm_phy_cable_test_start_rdb(struct phy_device *phydev)
+{
+ return _bcm_phy_cable_test_start(phydev, true);
+}
+EXPORT_SYMBOL_GPL(bcm_phy_cable_test_start_rdb);
+
+int bcm_phy_cable_test_get_status_rdb(struct phy_device *phydev,
+ bool *finished)
+{
+ return _bcm_phy_cable_test_get_status(phydev, finished, true);
+}
+EXPORT_SYMBOL_GPL(bcm_phy_cable_test_get_status_rdb);
+
MODULE_DESCRIPTION("Broadcom PHY Library");
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Broadcom Corporation");
diff --git a/drivers/net/phy/bcm-phy-lib.h b/drivers/net/phy/bcm-phy-lib.h
index b35d880220b9..237a8503c9b4 100644
--- a/drivers/net/phy/bcm-phy-lib.h
+++ b/drivers/net/phy/bcm-phy-lib.h
@@ -80,4 +80,10 @@ void bcm_phy_r_rc_cal_reset(struct phy_device *phydev);
int bcm_phy_28nm_a0b0_afe_config_init(struct phy_device *phydev);
int bcm_phy_enable_jumbo(struct phy_device *phydev);
+int bcm_phy_cable_test_get_status_rdb(struct phy_device *phydev,
+ bool *finished);
+int bcm_phy_cable_test_start_rdb(struct phy_device *phydev);
+int bcm_phy_cable_test_start(struct phy_device *phydev);
+int bcm_phy_cable_test_get_status(struct phy_device *phydev, bool *finished);
+
#endif /* _LINUX_BCM_PHY_LIB_H */
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 58d0150acc3e..d41624db6de2 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -119,6 +119,11 @@
#define MII_BCM54XX_RDB_ADDR 0x1e
#define MII_BCM54XX_RDB_DATA 0x1f
+/* legacy access control via rdb/expansion register */
+#define BCM54XX_RDB_REG0087 0x0087
+#define BCM54XX_EXP_REG7E (MII_BCM54XX_EXP_SEL_ER + 0x7E)
+#define BCM54XX_ACCESS_MODE_LEGACY_EN BIT(15)
+
/*
* AUXILIARY CONTROL SHADOW ACCESS REGISTERS. (PHY REG 0x18)
*/
@@ -294,4 +299,51 @@
#define MII_BRCM_CORE_EXPB0 0xB0
#define MII_BRCM_CORE_EXPB1 0xB1
+/* Enhanced Cable Diagnostics */
+#define BCM54XX_RDB_ECD_CTRL 0x2a0
+#define BCM54XX_EXP_ECD_CTRL (MII_BCM54XX_EXP_SEL_ER + 0xc0)
+
+#define BCM54XX_ECD_CTRL_CABLE_TYPE_CAT3 1 /* CAT3 or worse */
+#define BCM54XX_ECD_CTRL_CABLE_TYPE_CAT5 0 /* CAT5 or better */
+#define BCM54XX_ECD_CTRL_CABLE_TYPE_MASK BIT(0) /* cable type */
+#define BCM54XX_ECD_CTRL_INVALID BIT(3) /* invalid result */
+#define BCM54XX_ECD_CTRL_UNIT_CM 0 /* centimeters */
+#define BCM54XX_ECD_CTRL_UNIT_M 1 /* meters */
+#define BCM54XX_ECD_CTRL_UNIT_MASK BIT(10) /* cable length unit */
+#define BCM54XX_ECD_CTRL_IN_PROGRESS BIT(11) /* test in progress */
+#define BCM54XX_ECD_CTRL_BREAK_LINK BIT(12) /* unconnect link
+ * during test
+ */
+#define BCM54XX_ECD_CTRL_CROSS_SHORT_DIS BIT(13) /* disable inter-pair
+ * short check
+ */
+#define BCM54XX_ECD_CTRL_RUN BIT(15) /* run immediate */
+
+#define BCM54XX_RDB_ECD_FAULT_TYPE 0x2a1
+#define BCM54XX_EXP_ECD_FAULT_TYPE (MII_BCM54XX_EXP_SEL_ER + 0xc1)
+#define BCM54XX_ECD_FAULT_TYPE_INVALID 0x0
+#define BCM54XX_ECD_FAULT_TYPE_OK 0x1
+#define BCM54XX_ECD_FAULT_TYPE_OPEN 0x2
+#define BCM54XX_ECD_FAULT_TYPE_SAME_SHORT 0x3 /* short same pair */
+#define BCM54XX_ECD_FAULT_TYPE_CROSS_SHORT 0x4 /* short different pairs */
+#define BCM54XX_ECD_FAULT_TYPE_BUSY 0x9
+#define BCM54XX_ECD_FAULT_TYPE_PAIR_D_MASK GENMASK(3, 0)
+#define BCM54XX_ECD_FAULT_TYPE_PAIR_C_MASK GENMASK(7, 4)
+#define BCM54XX_ECD_FAULT_TYPE_PAIR_B_MASK GENMASK(11, 8)
+#define BCM54XX_ECD_FAULT_TYPE_PAIR_A_MASK GENMASK(15, 12)
+#define BCM54XX_ECD_PAIR_A_LENGTH_RESULTS 0x2a2
+#define BCM54XX_ECD_PAIR_B_LENGTH_RESULTS 0x2a3
+#define BCM54XX_ECD_PAIR_C_LENGTH_RESULTS 0x2a4
+#define BCM54XX_ECD_PAIR_D_LENGTH_RESULTS 0x2a5
+
+#define BCM54XX_RDB_ECD_PAIR_A_LENGTH_RESULTS 0x2a2
+#define BCM54XX_EXP_ECD_PAIR_A_LENGTH_RESULTS (MII_BCM54XX_EXP_SEL_ER + 0xc2)
+#define BCM54XX_RDB_ECD_PAIR_B_LENGTH_RESULTS 0x2a3
+#define BCM54XX_EXP_ECD_PAIR_B_LENGTH_RESULTS (MII_BCM54XX_EXP_SEL_ER + 0xc3)
+#define BCM54XX_RDB_ECD_PAIR_C_LENGTH_RESULTS 0x2a4
+#define BCM54XX_EXP_ECD_PAIR_C_LENGTH_RESULTS (MII_BCM54XX_EXP_SEL_ER + 0xc4)
+#define BCM54XX_RDB_ECD_PAIR_D_LENGTH_RESULTS 0x2a5
+#define BCM54XX_EXP_ECD_PAIR_D_LENGTH_RESULTS (MII_BCM54XX_EXP_SEL_ER + 0xc5)
+#define BCM54XX_ECD_LENGTH_RESULTS_INVALID 0xffff
+
#endif /* _LINUX_BRCMPHY_H */
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH net-next v2 4/4] net: phy: bcm54140: add cable diagnostics support
2020-05-13 16:35 [PATCH net-next 0/4] net: phy: broadcom: cable tester support Michael Walle
` (2 preceding siblings ...)
2020-05-13 16:35 ` [PATCH net-next v2 3/4] net: phy: broadcom: add cable test support Michael Walle
@ 2020-05-13 16:35 ` Michael Walle
2020-05-13 19:52 ` [PATCH net-next 0/4] net: phy: broadcom: cable tester support David Miller
4 siblings, 0 replies; 6+ messages in thread
From: Michael Walle @ 2020-05-13 16:35 UTC (permalink / raw)
To: netdev, linux-kernel
Cc: Andrew Lunn, Florian Fainelli, Heiner Kallweit, Russell King,
David S . Miller, Michael Walle
Use the generic cable tester functions from bcm-phy-lib to add cable
tester support.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair B, result: Open Circuit
Pair: Pair C, result: Open Circuit
Pair: Pair D, result: Open Circuit
Pair: Pair A, fault length: 106.60m
Pair: Pair B, fault length: 103.32m
Pair: Pair C, fault length: 104.96m
Pair: Pair D, fault length: 106.60m
1m cable, A/B connected, pair C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair D, result: Open Circuit
Pair: Pair C, fault length: 0.82m
Pair: Pair D, fault length: 1.64m
1m cable, A/B connected, pair C shorted with D:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short to another pair
Pair: Pair D, result: Short to another pair
Pair: Pair C, fault length: 1.64m
Pair: Pair D, fault length: 1.64m
The granularity of the length measurement seems to be 82cm.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/bcm54140.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/phy/bcm54140.c b/drivers/net/phy/bcm54140.c
index 9ef37a3bc2bb..8998e68bb26b 100644
--- a/drivers/net/phy/bcm54140.c
+++ b/drivers/net/phy/bcm54140.c
@@ -831,6 +831,7 @@ static struct phy_driver bcm54140_drivers[] = {
.phy_id = PHY_ID_BCM54140,
.phy_id_mask = BCM54140_PHY_ID_MASK,
.name = "Broadcom BCM54140",
+ .flags = PHY_POLL_CABLE_TEST,
.features = PHY_GBIT_FEATURES,
.config_init = bcm54140_config_init,
.did_interrupt = bcm54140_did_interrupt,
@@ -842,6 +843,8 @@ static struct phy_driver bcm54140_drivers[] = {
.soft_reset = genphy_soft_reset,
.get_tunable = bcm54140_get_tunable,
.set_tunable = bcm54140_set_tunable,
+ .cable_test_start = bcm_phy_cable_test_start_rdb,
+ .cable_test_get_status = bcm_phy_cable_test_get_status_rdb,
},
};
module_phy_driver(bcm54140_drivers);
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH net-next 0/4] net: phy: broadcom: cable tester support
2020-05-13 16:35 [PATCH net-next 0/4] net: phy: broadcom: cable tester support Michael Walle
` (3 preceding siblings ...)
2020-05-13 16:35 ` [PATCH net-next v2 4/4] net: phy: bcm54140: add cable diagnostics support Michael Walle
@ 2020-05-13 19:52 ` David Miller
4 siblings, 0 replies; 6+ messages in thread
From: David Miller @ 2020-05-13 19:52 UTC (permalink / raw)
To: michael; +Cc: netdev, linux-kernel, andrew, f.fainelli, hkallweit1, linux
From: Michael Walle <michael@walle.cc>
Date: Wed, 13 May 2020 18:35:20 +0200
> Add cable tester support for the Broadcom PHYs. Support for it was
> developed on a BCM54140 Quad PHY which RDB register access.
>
> If there is a link partner the results are not as good as with an open
> cable. I guess we could retry if the measurement until all pairs had at
> least one valid result.
>
> changes since v1:
> - added Reviewed-by: tags
> - removed "div by 2" for cross shorts, just mention it in the commit
> message. The results are inconclusive if the tests are repeated. So
> just report the length as is for now.
> - fixed typo in commit message
Series applied, thanks.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-05-13 19:52 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-13 16:35 [PATCH net-next 0/4] net: phy: broadcom: cable tester support Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 1/4] net: phy: broadcom: add exp register access methods without buslock Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 2/4] net: phy: broadcom: add bcm_phy_modify_exp() Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 3/4] net: phy: broadcom: add cable test support Michael Walle
2020-05-13 16:35 ` [PATCH net-next v2 4/4] net: phy: bcm54140: add cable diagnostics support Michael Walle
2020-05-13 19:52 ` [PATCH net-next 0/4] net: phy: broadcom: cable tester support David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).