[PATCH V3 1/3] clk: vc5: Allow Versaclock driver to support multiple instances

[PATCH V3 1/3] clk: vc5: Allow Versaclock driver to support multiple instances

[Adam Ford]

Currently, the Versaclock driver is only expecting one instance and
uses hard-coded names for the various clock names.  Unfortunately,
this is a problem when there is more than one instance of the driver,
because the subsequent instantiations of the driver use the identical
name.  Each clock after the fist fails to load, because the clock
subsystem cannot handle two clocks with identical name.

This patch removes the hard-coded name arrays and uses kasprintf to
assign clock names based on names of their respective node and parent
node which gives each clock a unique identifying name.

For a verasaclock node with a name like:
   versaclock5: versaclock_som@6a

The updated clock names would appear like:
    versaclock_som.mux
       versaclock_som.out0_sel_i2cb
       versaclock_som.pfd
          versaclock_som.pll
             versaclock_som.fod3
                versaclock_som.out4
             versaclock_som.fod2
                versaclock_som.out3
             versaclock_som.fod1
                versaclock_som.out2
             versaclock_som.fod0
                versaclock_som.out1

Signed-off-by: Adam Ford <aford173@gmail.com>
---
V3:  Remove 'probed' message
V2:  No change

diff --git a/drivers/clk/clk-versaclock5.c b/drivers/clk/clk-versaclock5.c
index fa96659f8023..41e3a75963b9 100644
--- a/drivers/clk/clk-versaclock5.c
+++ b/drivers/clk/clk-versaclock5.c
@@ -161,30 +161,6 @@ struct vc5_driver_data {
 	struct vc5_hw_data	clk_out[VC5_MAX_CLK_OUT_NUM];
 };
 
-static const char * const vc5_mux_names[] = {
-	"mux"
-};
-
-static const char * const vc5_dbl_names[] = {
-	"dbl"
-};
-
-static const char * const vc5_pfd_names[] = {
-	"pfd"
-};
-
-static const char * const vc5_pll_names[] = {
-	"pll"
-};
-
-static const char * const vc5_fod_names[] = {
-	"fod0", "fod1", "fod2", "fod3",
-};
-
-static const char * const vc5_clk_out_names[] = {
-	"out0_sel_i2cb", "out1", "out2", "out3", "out4",
-};
-
 /*
  * VersaClock5 i2c regmap
  */
@@ -692,8 +668,7 @@ static int vc5_map_index_to_output(const enum vc5_model model,
 
 static const struct of_device_id clk_vc5_of_match[];
 
-static int vc5_probe(struct i2c_client *client,
-		     const struct i2c_device_id *id)
+static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 {
 	struct vc5_driver_data *vc5;
 	struct clk_init_data init;
@@ -742,7 +717,7 @@ static int vc5_probe(struct i2c_client *client,
 	if (!IS_ERR(vc5->pin_clkin)) {
 		vc5->clk_mux_ins |= VC5_MUX_IN_CLKIN;
 		parent_names[init.num_parents++] =
-			__clk_get_name(vc5->pin_clkin);
+		    __clk_get_name(vc5->pin_clkin);
 	}
 
 	if (!init.num_parents) {
@@ -750,12 +725,13 @@ static int vc5_probe(struct i2c_client *client,
 		return -EINVAL;
 	}
 
-	init.name = vc5_mux_names[0];
+	init.name = kasprintf(GFP_KERNEL, "%pOFn.mux", client->dev.of_node);
 	init.ops = &vc5_mux_ops;
 	init.flags = 0;
 	init.parent_names = parent_names;
 	vc5->clk_mux.init = &init;
 	ret = devm_clk_hw_register(&client->dev, &vc5->clk_mux);
+	kfree(init.name);	/* clock framework made a copy of the name */
 	if (ret) {
 		dev_err(&client->dev, "unable to register %s\n", init.name);
 		goto err_clk;
@@ -764,13 +740,16 @@ static int vc5_probe(struct i2c_client *client,
 	if (vc5->chip_info->flags & VC5_HAS_PFD_FREQ_DBL) {
 		/* Register frequency doubler */
 		memset(&init, 0, sizeof(init));
-		init.name = vc5_dbl_names[0];
+		init.name = kasprintf(GFP_KERNEL, "%pOFn.dbl",
+				      client->dev.of_node);
 		init.ops = &vc5_dbl_ops;
 		init.flags = CLK_SET_RATE_PARENT;
-		init.parent_names = vc5_mux_names;
+		init.parent_names = parent_names;
+		parent_names[0] = clk_hw_get_name(&vc5->clk_mux);
 		init.num_parents = 1;
 		vc5->clk_mul.init = &init;
 		ret = devm_clk_hw_register(&client->dev, &vc5->clk_mul);
+		kfree(init.name); /* clock framework made a copy of the name */
 		if (ret) {
 			dev_err(&client->dev, "unable to register %s\n",
 				init.name);
@@ -780,16 +759,18 @@ static int vc5_probe(struct i2c_client *client,
 
 	/* Register PFD */
 	memset(&init, 0, sizeof(init));
-	init.name = vc5_pfd_names[0];
+	init.name = kasprintf(GFP_KERNEL, "%pOFn.pfd", client->dev.of_node);
 	init.ops = &vc5_pfd_ops;
 	init.flags = CLK_SET_RATE_PARENT;
+	init.parent_names = parent_names;
 	if (vc5->chip_info->flags & VC5_HAS_PFD_FREQ_DBL)
-		init.parent_names = vc5_dbl_names;
+		parent_names[0] = clk_hw_get_name(&vc5->clk_mul);
 	else
-		init.parent_names = vc5_mux_names;
+		parent_names[0] = clk_hw_get_name(&vc5->clk_mux);
 	init.num_parents = 1;
 	vc5->clk_pfd.init = &init;
 	ret = devm_clk_hw_register(&client->dev, &vc5->clk_pfd);
+	kfree(init.name);	/* clock framework made a copy of the name */
 	if (ret) {
 		dev_err(&client->dev, "unable to register %s\n", init.name);
 		goto err_clk;
@@ -797,15 +778,17 @@ static int vc5_probe(struct i2c_client *client,
 
 	/* Register PLL */
 	memset(&init, 0, sizeof(init));
-	init.name = vc5_pll_names[0];
+	init.name = kasprintf(GFP_KERNEL, "%pOFn.pll", client->dev.of_node);
 	init.ops = &vc5_pll_ops;
 	init.flags = CLK_SET_RATE_PARENT;
-	init.parent_names = vc5_pfd_names;
+	init.parent_names = parent_names;
+	parent_names[0] = clk_hw_get_name(&vc5->clk_pfd);
 	init.num_parents = 1;
 	vc5->clk_pll.num = 0;
 	vc5->clk_pll.vc5 = vc5;
 	vc5->clk_pll.hw.init = &init;
 	ret = devm_clk_hw_register(&client->dev, &vc5->clk_pll.hw);
+	kfree(init.name); /* clock framework made a copy of the name */
 	if (ret) {
 		dev_err(&client->dev, "unable to register %s\n", init.name);
 		goto err_clk;
@@ -815,15 +798,18 @@ static int vc5_probe(struct i2c_client *client,
 	for (n = 0; n < vc5->chip_info->clk_fod_cnt; n++) {
 		idx = vc5_map_index_to_output(vc5->chip_info->model, n);
 		memset(&init, 0, sizeof(init));
-		init.name = vc5_fod_names[idx];
+		init.name = kasprintf(GFP_KERNEL, "%pOFn.fod%d",
+				      client->dev.of_node, idx);
 		init.ops = &vc5_fod_ops;
 		init.flags = CLK_SET_RATE_PARENT;
-		init.parent_names = vc5_pll_names;
+		init.parent_names = parent_names;
+		parent_names[0] = clk_hw_get_name(&vc5->clk_pll.hw);
 		init.num_parents = 1;
 		vc5->clk_fod[n].num = idx;
 		vc5->clk_fod[n].vc5 = vc5;
 		vc5->clk_fod[n].hw.init = &init;
 		ret = devm_clk_hw_register(&client->dev, &vc5->clk_fod[n].hw);
+		kfree(init.name); /* clock framework made a copy of the name */
 		if (ret) {
 			dev_err(&client->dev, "unable to register %s\n",
 				init.name);
@@ -833,32 +819,36 @@ static int vc5_probe(struct i2c_client *client,
 
 	/* Register MUX-connected OUT0_I2C_SELB output */
 	memset(&init, 0, sizeof(init));
-	init.name = vc5_clk_out_names[0];
+	init.name = kasprintf(GFP_KERNEL, "%pOFn.out0_sel_i2cb",
+			      client->dev.of_node);
 	init.ops = &vc5_clk_out_ops;
 	init.flags = CLK_SET_RATE_PARENT;
-	init.parent_names = vc5_mux_names;
+	init.parent_names = parent_names;
+	parent_names[0] = clk_hw_get_name(&vc5->clk_mux);
 	init.num_parents = 1;
 	vc5->clk_out[0].num = idx;
 	vc5->clk_out[0].vc5 = vc5;
 	vc5->clk_out[0].hw.init = &init;
 	ret = devm_clk_hw_register(&client->dev, &vc5->clk_out[0].hw);
+	kfree(init.name);	/* clock framework made a copy of the name */
 	if (ret) {
-		dev_err(&client->dev, "unable to register %s\n",
-			init.name);
+		dev_err(&client->dev, "unable to register %s\n", init.name);
 		goto err_clk;
 	}
 
 	/* Register FOD-connected OUTx outputs */
 	for (n = 1; n < vc5->chip_info->clk_out_cnt; n++) {
 		idx = vc5_map_index_to_output(vc5->chip_info->model, n - 1);
-		parent_names[0] = vc5_fod_names[idx];
+		parent_names[0] = clk_hw_get_name(&vc5->clk_fod[idx].hw);
 		if (n == 1)
-			parent_names[1] = vc5_mux_names[0];
+			parent_names[1] = clk_hw_get_name(&vc5->clk_mux);
 		else
-			parent_names[1] = vc5_clk_out_names[n - 1];
+			parent_names[1] =
+			    clk_hw_get_name(&vc5->clk_out[n - 1].hw);
 
 		memset(&init, 0, sizeof(init));
-		init.name = vc5_clk_out_names[idx + 1];
+		init.name = kasprintf(GFP_KERNEL, "%pOFn.out%d",
+				      client->dev.of_node, idx + 1);
 		init.ops = &vc5_clk_out_ops;
 		init.flags = CLK_SET_RATE_PARENT;
 		init.parent_names = parent_names;
@@ -866,8 +856,8 @@ static int vc5_probe(struct i2c_client *client,
 		vc5->clk_out[n].num = idx;
 		vc5->clk_out[n].vc5 = vc5;
 		vc5->clk_out[n].hw.init = &init;
-		ret = devm_clk_hw_register(&client->dev,
-					   &vc5->clk_out[n].hw);
+		ret = devm_clk_hw_register(&client->dev, &vc5->clk_out[n].hw);
+		kfree(init.name); /* clock framework made a copy of the name */
 		if (ret) {
 			dev_err(&client->dev, "unable to register %s\n",
 				init.name);
-- 
2.17.1

[PATCH V3 2/3] dt: Add additional option bindings for IDT VersaClock

[Adam Ford]

The VersaClock driver now supports some additional bindings to support
child nodes which can configure optional settings like mode, voltage
and slew.

This patch updates the binding document to describe what is available
in the driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
V3:  Re-order binding change and driver change so biding comes first.
     Move all binding related changes to this patch.

diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
index bcff681a4bd0..6165b6ddb1a9 100644
--- a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
+++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
@@ -31,6 +31,29 @@ Required properties:
 		- 5p49v5933 and
 		- 5p49v5935: (optional) property not present or "clkin".
 
+For all output ports, a corresponding, optional child node named OUT1,
+OUT2, etc. can represent a each output, and the node can be used to
+specify the following:
+
+- itd,mode: can be one of the following:
+                 - VC5_LVPECL
+                 - VC5_CMOS
+                 - VC5_HCSL33
+                 - VC5_LVDS
+                 - VC5_CMOS2
+                 - VC5_CMOSD
+                 - VC5_HCSL25
+
+- idt,voltage-microvolts:  can be one of the following
+                 - 1800000
+                 - 2500000
+                 - 3300000
+-  idt,slew-percent: Percent of normal, can be one of
+                 - 80
+                 - 85
+                 - 90
+                 - 100
+
 ==Mapping between clock specifier and physical pins==
 
 When referencing the provided clock in the DT using phandle and
@@ -81,6 +104,16 @@ i2c-master-node {
 		/* Connect XIN input to 25MHz reference */
 		clocks = <&ref25m>;
 		clock-names = "xin";
+
+		OUT1 {
+			itd,mode = <VC5_CMOS>;
+			idt,voltage-microvolts = <1800000>;
+			idt,slew-percent = <80>;
+		};
+		OUT2 {
+			...
+		};
+		...
 	};
 };
 
diff --git a/include/dt-bindings/clk/versaclock.h b/include/dt-bindings/clk/versaclock.h
new file mode 100644
index 000000000000..c6a6a0946564
--- /dev/null
+++ b/include/dt-bindings/clk/versaclock.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* This file defines field values used by the versaclock 6 family
+ * for defining output type
+ */
+
+#define VC5_LVPECL	0
+#define VC5_CMOS	1
+#define VC5_HCSL33	2
+#define VC5_LVDS	3
+#define VC5_CMOS2	4
+#define VC5_CMOSD	5
+#define VC5_HCSL25	6
-- 
2.17.1

[PATCH V3 3/3] clk: vc5: Enable addition output configurations of the Versaclock

[Adam Ford]

The existing driver is expecting the Versaclock to be pre-programmed,
and only sets the output frequency.  Unfortunately, not all devices
are pre-programmed, and the Versaclock chip has more options beyond
just the frequency.

This patch enables the following additional features:

   - Programmable voltage: 1.8V, 2.5V, or 3.3V​
   - Slew Percentage of normal: 85%, 90%, or 100%
   - Output Type: LVPECL, CMOS, HCSL, or LVDS

Signed-off-by: Adam Ford <aford173@gmail.com>
---
V3:  Make source code change following the binding changes since there
     is a dependency and move changes to binding header file to the
     patch with bindings changes.

diff --git a/drivers/clk/clk-versaclock5.c b/drivers/clk/clk-versaclock5.c
index 41e3a75963b9..9a5fb3834b9a 100644
--- a/drivers/clk/clk-versaclock5.c
+++ b/drivers/clk/clk-versaclock5.c
@@ -24,6 +24,8 @@
 #include <linux/regmap.h>
 #include <linux/slab.h>
 
+#include <dt-bindings/clk/versaclock.h>
+
 /* VersaClock5 registers */
 #define VC5_OTP_CONTROL				0x00
 
@@ -89,6 +91,28 @@
 
 /* Clock control register for clock 1,2 */
 #define VC5_CLK_OUTPUT_CFG(idx, n)	(0x60 + ((idx) * 0x2) + (n))
+#define VC5_CLK_OUTPUT_CFG0_CFG_SHIFT	5
+#define VC5_CLK_OUTPUT_CFG0_CFG_MASK GENMASK(7, VC5_CLK_OUTPUT_CFG0_CFG_SHIFT)
+
+#define VC5_CLK_OUTPUT_CFG0_CFG_LVPECL	(VC5_LVPECL)
+#define VC5_CLK_OUTPUT_CFG0_CFG_CMOS		(VC5_CMOS)
+#define VC5_CLK_OUTPUT_CFG0_CFG_HCSL33	(VC5_HCSL33)
+#define VC5_CLK_OUTPUT_CFG0_CFG_LVDS		(VC5_LVDS)
+#define VC5_CLK_OUTPUT_CFG0_CFG_CMOS2		(VC5_CMOS2)
+#define VC5_CLK_OUTPUT_CFG0_CFG_CMOSD		(VC5_CMOSD)
+#define VC5_CLK_OUTPUT_CFG0_CFG_HCSL25	(VC5_HCSL25)
+
+#define VC5_CLK_OUTPUT_CFG0_PWR_SHIFT	3
+#define VC5_CLK_OUTPUT_CFG0_PWR_MASK GENMASK(4, VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_PWR_18	(0<<VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_PWR_25	(2<<VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_PWR_33	(3<<VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT	0
+#define VC5_CLK_OUTPUT_CFG0_SLEW_MASK GENMASK(1, VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_SLEW_80	(0<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_SLEW_85	(1<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_SLEW_90	(2<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
+#define VC5_CLK_OUTPUT_CFG0_SLEW_100	(3<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
 #define VC5_CLK_OUTPUT_CFG1_EN_CLKBUF	BIT(0)
 
 #define VC5_CLK_OE_SHDN				0x68
@@ -143,6 +167,8 @@ struct vc5_hw_data {
 	u32			div_int;
 	u32			div_frc;
 	unsigned int		num;
+	unsigned int		clk_output_cfg0;
+	unsigned int		clk_output_cfg0_mask;
 };
 
 struct vc5_driver_data {
@@ -567,6 +593,17 @@ static int vc5_clk_out_prepare(struct clk_hw *hw)
 	regmap_update_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
 			   VC5_CLK_OUTPUT_CFG1_EN_CLKBUF,
 			   VC5_CLK_OUTPUT_CFG1_EN_CLKBUF);
+	if (hwdata->clk_output_cfg0_mask) {
+		dev_dbg(&vc5->client->dev, "Update output %d mask 0x%0X val 0x%0X\n",
+			hwdata->num, hwdata->clk_output_cfg0_mask,
+			hwdata->clk_output_cfg0);
+
+		regmap_update_bits(vc5->regmap,
+			VC5_CLK_OUTPUT_CFG(hwdata->num, 0),
+			hwdata->clk_output_cfg0_mask,
+			hwdata->clk_output_cfg0);
+	}
+
 	return 0;
 }
 
@@ -666,6 +703,120 @@ static int vc5_map_index_to_output(const enum vc5_model model,
 	}
 }
 
+static int vc5_update_mode(struct device_node *np_output,
+			   struct vc5_hw_data *clk_out)
+{
+	u32 value;
+
+	if (!of_property_read_u32(np_output, "idt,mode", &value)) {
+		clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_CFG_MASK;
+		switch (value) {
+		case VC5_CLK_OUTPUT_CFG0_CFG_LVPECL:
+		case VC5_CLK_OUTPUT_CFG0_CFG_CMOS:
+		case VC5_CLK_OUTPUT_CFG0_CFG_HCSL33:
+		case VC5_CLK_OUTPUT_CFG0_CFG_LVDS:
+		case VC5_CLK_OUTPUT_CFG0_CFG_CMOS2:
+		case VC5_CLK_OUTPUT_CFG0_CFG_CMOSD:
+		case VC5_CLK_OUTPUT_CFG0_CFG_HCSL25:
+			clk_out->clk_output_cfg0 |=
+			    value << VC5_CLK_OUTPUT_CFG0_CFG_SHIFT;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+	return 0;
+}
+
+static int vc5_update_power(struct device_node *np_output,
+			    struct vc5_hw_data *clk_out)
+{
+	u32 value;
+
+	if (!of_property_read_u32(np_output,
+				  "idt,voltage-microvolts", &value)) {
+		clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_PWR_MASK;
+		switch (value) {
+		case 1800000:
+			clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_18;
+			break;
+		case 2500000:
+			clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_25;
+			break;
+		case 3300000:
+			clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_33;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+	return 0;
+}
+
+static int vc5_update_slew(struct device_node *np_output,
+			   struct vc5_hw_data *clk_out)
+{
+	u32 value;
+
+	if (!of_property_read_u32(np_output, "idt,slew-percent", &value)) {
+		clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_SLEW_MASK;
+		switch (value) {
+		case 80:
+			clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_80;
+			break;
+		case 85:
+			clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_85;
+			break;
+		case 90:
+			clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_90;
+			break;
+		case 100:
+			clk_out->clk_output_cfg0 |=
+			    VC5_CLK_OUTPUT_CFG0_SLEW_100;
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+	return 0;
+}
+
+static int vc5_get_output_config(struct i2c_client *client,
+				 struct vc5_hw_data *clk_out)
+{
+	struct device_node *np_output;
+	char *child_name;
+	int ret = 0;
+
+	child_name = kasprintf(GFP_KERNEL, "OUT%d", clk_out->num + 1);
+	np_output = of_get_child_by_name(client->dev.of_node, child_name);
+	kfree(child_name);
+	if (!np_output)
+		goto output_done;
+
+	ret = vc5_update_mode(np_output, clk_out);
+	if (ret)
+		goto output_error;
+
+	ret = vc5_update_power(np_output, clk_out);
+	if (ret)
+		goto output_error;
+
+	ret = vc5_update_slew(np_output, clk_out);
+
+output_error:
+	if (ret) {
+		dev_err(&client->dev,
+			"Invalid clock output configuration OUT%d\n",
+			clk_out->num + 1);
+	}
+
+	of_node_put(np_output);
+
+output_done:
+	return ret;
+}
+
 static const struct of_device_id clk_vc5_of_match[];
 
 static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
@@ -863,6 +1014,11 @@ static int vc5_probe(struct i2c_client *client, const struct i2c_device_id *id)
 				init.name);
 			goto err_clk;
 		}
+
+		/* Fetch Clock Output configuration from DT (if specified) */
+		ret = vc5_get_output_config(client, &vc5->clk_out[n]);
+		if (ret)
+			goto err_clk;
 	}
 
 	ret = of_clk_add_hw_provider(client->dev.of_node, vc5_of_clk_get, vc5);
-- 
2.17.1

Re: [PATCH V3 1/3] clk: vc5: Allow Versaclock driver to support multiple instances

[Stephen Boyd]

Quoting Adam Ford (2020-06-03 08:43:27)
> Currently, the Versaclock driver is only expecting one instance and
> uses hard-coded names for the various clock names.  Unfortunately,
> this is a problem when there is more than one instance of the driver,
> because the subsequent instantiations of the driver use the identical
> name.  Each clock after the fist fails to load, because the clock
> subsystem cannot handle two clocks with identical name.
> 
> This patch removes the hard-coded name arrays and uses kasprintf to
> assign clock names based on names of their respective node and parent
> node which gives each clock a unique identifying name.
> 
> For a verasaclock node with a name like:
>    versaclock5: versaclock_som@6a
> 
> The updated clock names would appear like:
>     versaclock_som.mux
>        versaclock_som.out0_sel_i2cb
>        versaclock_som.pfd
>           versaclock_som.pll
>              versaclock_som.fod3
>                 versaclock_som.out4
>              versaclock_som.fod2
>                 versaclock_som.out3
>              versaclock_som.fod1
>                 versaclock_som.out2
>              versaclock_som.fod0
>                 versaclock_som.out1
> 
> Signed-off-by: Adam Ford <aford173@gmail.com>
> ---

Applied to clk-next

Re: [PATCH V3 2/3] dt: Add additional option bindings for IDT VersaClock

[Stephen Boyd]

Quoting Adam Ford (2020-06-03 08:43:28)
> The VersaClock driver now supports some additional bindings to support
> child nodes which can configure optional settings like mode, voltage
> and slew.
> 
> This patch updates the binding document to describe what is available
> in the driver.
> 
> Signed-off-by: Adam Ford <aford173@gmail.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---

Applied to clk-next

Re: [PATCH V3 3/3] clk: vc5: Enable addition output configurations of the Versaclock

[Stephen Boyd]

Quoting Adam Ford (2020-06-03 08:43:29)
> The existing driver is expecting the Versaclock to be pre-programmed,
> and only sets the output frequency.  Unfortunately, not all devices
> are pre-programmed, and the Versaclock chip has more options beyond
> just the frequency.
> 
> This patch enables the following additional features:
> 
>    - Programmable voltage: 1.8V, 2.5V, or 3.3V\u200b
>    - Slew Percentage of normal: 85%, 90%, or 100%
>    - Output Type: LVPECL, CMOS, HCSL, or LVDS
> 
> Signed-off-by: Adam Ford <aford173@gmail.com>
> ---

Applied to clk-next

Re: [PATCH V3 1/3] clk: vc5: Allow Versaclock driver to support multiple instances

[Geert Uytterhoeven]

Hi Adam,

On Wed, Jun 3, 2020 at 5:44 PM Adam Ford <aford173@gmail.com> wrote:
> Currently, the Versaclock driver is only expecting one instance and
> uses hard-coded names for the various clock names.  Unfortunately,
> this is a problem when there is more than one instance of the driver,
> because the subsequent instantiations of the driver use the identical
> name.  Each clock after the fist fails to load, because the clock
> subsystem cannot handle two clocks with identical name.

Thanks for your patch, which is now commit f491276a51685987 ("clk: vc5:
Allow Versaclock driver to support multiple instances") in clk-next.

> This patch removes the hard-coded name arrays and uses kasprintf to
> assign clock names based on names of their respective node and parent
> node which gives each clock a unique identifying name.
>
> For a verasaclock node with a name like:
>    versaclock5: versaclock_som@6a
>
> The updated clock names would appear like:
>     versaclock_som.mux
>        versaclock_som.out0_sel_i2cb
>        versaclock_som.pfd
>           versaclock_som.pll
>              versaclock_som.fod3
>                 versaclock_som.out4
>              versaclock_som.fod2
>                 versaclock_som.out3
>              versaclock_som.fod1
>                 versaclock_som.out2
>              versaclock_som.fod0
>                 versaclock_som.out1

I'm afraid this won't help, as all versaclock nodes should be named
"clock-controller@<unit-address>", as per DT generic node name
recommendations.
Incorporating the unit-address won't help, as you can have multiple
i2c buses in the system.
How do other drivers handle this?

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds