[PATCH v2 0/6] Introduce PMIC based USB type C detection

[PATCH v2 0/6] Introduce PMIC based USB type C detection

[Wesley Cheng]

Changes in v2:
 - Use devm_kzalloc() in qcom_pmic_typec_probe()
 - Add checks to make sure return value of typec_find_port_power_role() is
   valid
 - Added a VBUS output regulator driver, which will be used by the PMIC USB
   type c driver to enable/disable the source
 - Added logic to control vbus source from the PMIC type c driver when
   UFP/DFP is detected
 - Added dt-binding for this new regulator driver
 - Fixed Kconfig typec notation to match others
 - Leave type C block disabled until enabled by a platform DTS

Add the required drivers for implementing type C orientation and role
detection using the Qualcomm PMIC.  Currently, PMICs such as the PM8150B
have an integrated type C block, which can be utilized for this.  This
series adds the dt-binding, PMIC type C driver, and DTS nodes.

The PMIC type C driver will register itself as a type C port w/ a
registered type C switch for orientation, and will fetch a USB role switch
handle for the role notifications.  It will also have the ability to enable
the VBUS output to any connected devices based on if the device is behaving
as a UFP or DFP.

Wesley Cheng (6):
  usb: typec: Add QCOM PMIC typec detection driver
  dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding
  arm64: boot: dts: qcom: pm8150b: Add node for USB type C block
  regulator: Add support for QCOM PMIC VBUS booster
  dt-bindings: regulator: Add dt-binding for QCOM PMIC VBUS output
    regulator
  arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster

 .../regulator/qcom,usb-vbus-regulator.yaml    |  41 +++
 .../bindings/usb/qcom,pmic-typec.yaml         | 117 ++++++++
 arch/arm64/boot/dts/qcom/pm8150b.dtsi         |  13 +
 arch/arm64/boot/dts/qcom/sm8150-mtp.dts       |   7 +
 drivers/regulator/Kconfig                     |  10 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/qcom_usb_vbus-regulator.c   | 147 ++++++++++
 drivers/usb/typec/Kconfig                     |  12 +
 drivers/usb/typec/Makefile                    |   1 +
 drivers/usb/typec/qcom-pmic-typec.c           | 275 ++++++++++++++++++
 10 files changed, 624 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml
 create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
 create mode 100644 drivers/regulator/qcom_usb_vbus-regulator.c
 create mode 100644 drivers/usb/typec/qcom-pmic-typec.c

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v2 1/6] usb: typec: Add QCOM PMIC typec detection driver

[Wesley Cheng]

The QCOM SPMI typec driver handles the role and orientation detection, and
notifies client drivers using the USB role switch framework.   It registers
as a typec port, so orientation can be communicated using the typec switch
APIs.  The driver also attains a handle to the VBUS output regulator, so it
can enable/disable the VBUS source when acting as a host/device.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 drivers/usb/typec/Kconfig           |  12 ++
 drivers/usb/typec/Makefile          |   1 +
 drivers/usb/typec/qcom-pmic-typec.c | 275 ++++++++++++++++++++++++++++
 3 files changed, 288 insertions(+)
 create mode 100644 drivers/usb/typec/qcom-pmic-typec.c

diff --git a/drivers/usb/typec/Kconfig b/drivers/usb/typec/Kconfig
index b4f2aac7ae8a..595c14766e99 100644
--- a/drivers/usb/typec/Kconfig
+++ b/drivers/usb/typec/Kconfig
@@ -72,6 +72,18 @@ config TYPEC_TPS6598X
 	  If you choose to build this driver as a dynamically linked module, the
 	  module will be called tps6598x.ko.
 
+config TYPEC_QCOM_PMIC
+	tristate "Qualcomm PMIC USB Type-C driver"
+	depends on ARCH_QCOM
+	help
+	  Driver for supporting role switch over the Qualcomm PMIC.  This will
+	  handle the USB Type-C role and orientation detection reported by the
+	  QCOM PMIC if the PMIC has the capability to handle USB Type-C
+	  detection.
+
+	  It will also enable the VBUS output to connected devices when a
+	  DFP connection is made.
+
 source "drivers/usb/typec/mux/Kconfig"
 
 source "drivers/usb/typec/altmodes/Kconfig"
diff --git a/drivers/usb/typec/Makefile b/drivers/usb/typec/Makefile
index 7753a5c3cd46..cceffd987643 100644
--- a/drivers/usb/typec/Makefile
+++ b/drivers/usb/typec/Makefile
@@ -6,4 +6,5 @@ obj-$(CONFIG_TYPEC_TCPM)	+= tcpm/
 obj-$(CONFIG_TYPEC_UCSI)	+= ucsi/
 obj-$(CONFIG_TYPEC_HD3SS3220)	+= hd3ss3220.o
 obj-$(CONFIG_TYPEC_TPS6598X)	+= tps6598x.o
+obj-$(CONFIG_TYPEC_QCOM_PMIC)	+= qcom-pmic-typec.o
 obj-$(CONFIG_TYPEC)		+= mux/
diff --git a/drivers/usb/typec/qcom-pmic-typec.c b/drivers/usb/typec/qcom-pmic-typec.c
new file mode 100644
index 000000000000..5ae3af03c638
--- /dev/null
+++ b/drivers/usb/typec/qcom-pmic-typec.c
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/err.h>
+#include <linux/regmap.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/usb/role.h>
+#include <linux/usb/typec_mux.h>
+#include <linux/regulator/consumer.h>
+
+#define TYPEC_MISC_STATUS		0xb
+#define CC_ATTACHED			BIT(0)
+#define CC_ORIENTATION			BIT(1)
+#define SNK_SRC_MODE			BIT(6)
+#define TYPEC_MODE_CFG			0x44
+#define TYPEC_DISABLE_CMD		BIT(0)
+#define EN_SNK_ONLY			BIT(1)
+#define EN_SRC_ONLY			BIT(2)
+#define TYPEC_VCONN_CONTROL		0x46
+#define VCONN_EN_SRC			BIT(0)
+#define VCONN_EN_VAL			BIT(1)
+#define TYPEC_EXIT_STATE_CFG		0x50
+#define SEL_SRC_UPPER_REF		BIT(2)
+#define TYPEC_INTR_EN_CFG_1		0x5e
+#define TYPEC_INTR_EN_CFG_1_MASK	GENMASK(7, 0)
+
+struct qcom_pmic_typec {
+	struct device		*dev;
+	struct fwnode_handle	*fwnode;
+	struct regmap		*regmap;
+	u32			base;
+
+	struct typec_capability *cap;
+	struct typec_port	*port;
+	struct usb_role_switch *role_sw;
+
+	struct regulator	*vbus_reg;
+	bool			vbus_enabled;
+};
+
+static void qcom_pmic_typec_enable_vbus_regulator(struct qcom_pmic_typec
+							*qcom_usb, bool enable)
+{
+	int ret = 0;
+
+	if (enable == qcom_usb->vbus_enabled)
+		return;
+
+	if (!qcom_usb->vbus_reg) {
+		qcom_usb->vbus_reg = devm_regulator_get(qcom_usb->dev,
+							"usb_vbus");
+		if (IS_ERR(qcom_usb->vbus_reg)) {
+			qcom_usb->vbus_reg = NULL;
+			return;
+		}
+	}
+
+	if (enable) {
+		ret = regulator_enable(qcom_usb->vbus_reg);
+		if (ret)
+			return;
+	} else {
+		ret = regulator_disable(qcom_usb->vbus_reg);
+		if (ret)
+			return;
+	}
+	qcom_usb->vbus_enabled = enable;
+}
+
+static void qcom_pmic_typec_check_connection(struct qcom_pmic_typec *qcom_usb)
+{
+	enum typec_orientation orientation;
+	enum usb_role role;
+	unsigned int stat;
+	bool enable_vbus;
+
+	regmap_read(qcom_usb->regmap, qcom_usb->base + TYPEC_MISC_STATUS,
+		    &stat);
+
+	if (stat & CC_ATTACHED) {
+		orientation = ((stat & CC_ORIENTATION) >> 1) ?
+				TYPEC_ORIENTATION_REVERSE :
+				TYPEC_ORIENTATION_NORMAL;
+		typec_set_orientation(qcom_usb->port, orientation);
+
+		role = (stat & SNK_SRC_MODE) ? USB_ROLE_HOST : USB_ROLE_DEVICE;
+		if (role == USB_ROLE_HOST)
+			enable_vbus = true;
+		else
+			enable_vbus = false;
+	} else {
+		role = USB_ROLE_NONE;
+		enable_vbus = false;
+	}
+
+	qcom_pmic_typec_enable_vbus_regulator(qcom_usb, enable_vbus);
+	usb_role_switch_set_role(qcom_usb->role_sw, role);
+}
+
+static irqreturn_t qcom_pmic_typec_interrupt(int irq, void *_qcom_usb)
+{
+	struct qcom_pmic_typec *qcom_usb = _qcom_usb;
+
+	qcom_pmic_typec_check_connection(qcom_usb);
+	return IRQ_HANDLED;
+}
+
+static void qcom_pmic_typec_typec_hw_init(struct qcom_pmic_typec *qcom_usb)
+{
+	u8 mode = 0;
+
+	regmap_update_bits(qcom_usb->regmap,
+			   qcom_usb->base + TYPEC_INTR_EN_CFG_1,
+			   TYPEC_INTR_EN_CFG_1_MASK, 0);
+
+	if (qcom_usb->cap->type != TYPEC_PORT_DRP)
+		mode = (qcom_usb->cap->type == TYPEC_PORT_SNK) ?
+					EN_SNK_ONLY : EN_SRC_ONLY;
+	regmap_update_bits(qcom_usb->regmap, qcom_usb->base + TYPEC_MODE_CFG,
+			   EN_SNK_ONLY | EN_SRC_ONLY, mode);
+
+	regmap_update_bits(qcom_usb->regmap,
+			   qcom_usb->base + TYPEC_VCONN_CONTROL,
+			   VCONN_EN_SRC | VCONN_EN_VAL, VCONN_EN_SRC);
+	regmap_update_bits(qcom_usb->regmap,
+			   qcom_usb->base + TYPEC_EXIT_STATE_CFG,
+			   SEL_SRC_UPPER_REF, SEL_SRC_UPPER_REF);
+}
+
+static int qcom_pmic_typec_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qcom_pmic_typec *qcom_usb;
+	struct typec_capability *cap;
+	const char *buf;
+	int ret, irq, role;
+	u32 reg;
+
+	ret = of_property_read_u32(dev->of_node, "reg", &reg);
+	if (ret < 0) {
+		dev_err(dev, "missing base address");
+		return ret;
+	}
+
+	qcom_usb = devm_kzalloc(dev, sizeof(*qcom_usb), GFP_KERNEL);
+	if (!qcom_usb)
+		return -ENOMEM;
+
+	qcom_usb->dev = dev;
+	qcom_usb->base = reg;
+
+	qcom_usb->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!qcom_usb->regmap) {
+		dev_err(dev, "Failed to get regmap\n");
+		return -EINVAL;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "Failed to get CC irq\n");
+		return -EINVAL;
+	}
+
+	ret = devm_request_threaded_irq(qcom_usb->dev, irq, NULL,
+					qcom_pmic_typec_interrupt, IRQF_ONESHOT,
+					"qcom-pmic-typec", qcom_usb);
+	if (ret) {
+		dev_err(&pdev->dev, "Could not request IRQ\n");
+		return ret;
+	}
+
+	qcom_usb->fwnode = device_get_named_child_node(dev, "connector");
+	if (!qcom_usb->fwnode)
+		return -EINVAL;
+
+	cap = devm_kzalloc(dev, sizeof(*cap), GFP_KERNEL);
+	if (!cap) {
+		ret = -ENOMEM;
+		goto err_put_node;
+	}
+
+	ret = fwnode_property_read_string(qcom_usb->fwnode, "power-role", &buf);
+	if (!ret) {
+		role = typec_find_port_power_role(buf);
+		if (role < 0)
+			role = TYPEC_PORT_SNK;
+	} else {
+		role = TYPEC_PORT_SNK;
+	}
+	cap->type = role;
+
+	ret = fwnode_property_read_string(qcom_usb->fwnode, "data-role", &buf);
+	if (!ret) {
+		role = typec_find_port_data_role(buf);
+		if (role < 0)
+			role = TYPEC_PORT_UFP;
+	} else {
+		role = TYPEC_PORT_UFP;
+	}
+	cap->data = role;
+
+	cap->prefer_role = TYPEC_NO_PREFERRED_ROLE;
+	cap->fwnode = qcom_usb->fwnode;
+	qcom_usb->port = typec_register_port(dev, cap);
+	if (IS_ERR(qcom_usb->port)) {
+		ret = PTR_ERR(qcom_usb->port);
+		dev_err(dev, "Failed to register type c port %d\n", ret);
+		goto err_put_node;
+	}
+
+	qcom_usb->cap = cap;
+
+	qcom_usb->role_sw = fwnode_usb_role_switch_get(qcom_usb->fwnode);
+	if (IS_ERR(qcom_usb->role_sw)) {
+		if (PTR_ERR(qcom_usb->role_sw) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get role switch\n");
+		ret = PTR_ERR(qcom_usb->role_sw);
+		goto err_typec_port;
+	}
+
+	platform_set_drvdata(pdev, qcom_usb);
+	qcom_pmic_typec_typec_hw_init(qcom_usb);
+	qcom_pmic_typec_check_connection(qcom_usb);
+
+	return 0;
+
+err_typec_port:
+	typec_unregister_port(qcom_usb->port);
+err_put_node:
+	fwnode_handle_put(qcom_usb->fwnode);
+
+	return ret;
+}
+
+static int qcom_pmic_typec_remove(struct platform_device *pdev)
+{
+	struct qcom_pmic_typec *qcom_usb = platform_get_drvdata(pdev);
+
+	usb_role_switch_set_role(qcom_usb->role_sw, USB_ROLE_NONE);
+	qcom_pmic_typec_enable_vbus_regulator(qcom_usb, 0);
+
+	typec_unregister_port(qcom_usb->port);
+	usb_role_switch_put(qcom_usb->role_sw);
+	fwnode_handle_put(qcom_usb->fwnode);
+
+	return 0;
+}
+
+static const struct of_device_id qcom_pmic_typec_table[] = {
+	{ .compatible = "qcom,pm8150b-usb-typec" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_pmic_typec_table);
+
+static struct platform_driver qcom_pmic_typec = {
+	.driver = {
+		.name = "qcom,pmic-typec",
+		.of_match_table = qcom_pmic_typec_table,
+	},
+	.probe = qcom_pmic_typec_probe,
+	.remove = qcom_pmic_typec_remove,
+};
+
+module_platform_driver(qcom_pmic_typec);
+
+MODULE_DESCRIPTION("QCOM PMIC USB type C driver");
+MODULE_LICENSE("GPL v2");
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v2 2/6] dt-bindings: usb: Add Qualcomm PMIC type C controller dt-binding

[Wesley Cheng]

Introduce the dt-binding for enabling USB type C orientation and role
detection using the PM8150B.  The driver will be responsible for receiving
the interrupt at a state change on the CC lines, reading the orientation/role,
and communicating this information to the remote clients, which can include
a role switch node and a type C switch.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 .../bindings/usb/qcom,pmic-typec.yaml         | 117 ++++++++++++++++++
 1 file changed, 117 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml

diff --git a/Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml b/Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
new file mode 100644
index 000000000000..085b4547d75a
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/qcom,pmic-typec.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/usb/qcom,pmic-typec.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm PMIC based USB type C Detection Driver
+
+maintainers:
+  - Wesley Cheng <wcheng@codeaurora.org>
+
+description: |
+  Qualcomm PMIC Type C Detect
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm8150b-usb-typec
+
+  reg:
+    maxItems: 1
+    description: Type C base address
+
+  interrupts:
+    maxItems: 1
+    description: CC change interrupt from PMIC
+
+  connector:
+    description: Connector type for remote endpoints
+    type: object
+
+    properties:
+      compatible:
+        enum:
+          - usb-c-connector
+
+      power-role:
+       enum:
+         - dual
+         - source
+         - sink
+
+      data-role:
+        enum:
+          - dual
+          - host
+          - device
+
+      port:
+        description: Remote endpoint connections
+        type: object
+
+        properties:
+          endpoint@0:
+            description: Connection to USB type C mux node
+            type: object
+
+            properties:
+              remote-endpoint:
+                maxItems: 1
+                description: Node reference to the type C mux
+
+          endpoint@1:
+            description: Connection to role switch node
+            type: object
+
+            properties:
+              remote-endpoint:
+                maxItems: 1
+                description: Node reference to the role switch node
+
+    required:
+      - compatible
+
+required:
+  - compatible
+  - interrupts
+  - connector
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    pm8150b {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        qcom,typec@1500 {
+            compatible = "qcom,pm8150b-usb-typec";
+            reg = <0x1500>;
+            interrupts =
+                <0x2 0x15 0x5 IRQ_TYPE_EDGE_RISING>;
+
+            connector {
+                compatible = "usb-c-connector";
+                power-role = "dual";
+                data-role = "dual";
+                port {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+                    usb3_data_ss: endpoint@0 {
+                        reg = <0>;
+                        remote-endpoint =
+                                <&qmp_ss_mux>;
+                    };
+
+                    usb3_role: endpoint@1 {
+
+                        reg = <1>;
+                        remote-endpoint =
+                                <&dwc3_drd_switch>;
+                    };
+                };
+            };
+        };
+    };
+...
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v2 3/6] arm64: boot: dts: qcom: pm8150b: Add node for USB type C block

[Wesley Cheng]

The PM8150B has a dedicated USB type C block, which can be used for type C
orientation and role detection.  Create the reference node to this type C
block for further use.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/pm8150b.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
index 322379d5c31f..ec44a8bc2f84 100644
--- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -22,6 +22,14 @@ power-on@800 {
 			status = "disabled";
 		};
 
+		qcom,typec@1500 {
+			compatible = "qcom,pm8150b-usb-typec";
+			status = "disabled";
+			reg = <0x1500>;
+			interrupts =
+				<0x2 0x15 0x5 IRQ_TYPE_EDGE_RISING>;
+		};
+
 		adc@3100 {
 			compatible = "qcom,spmi-adc5";
 			reg = <0x3100>;
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v2 4/6] regulator: Add support for QCOM PMIC VBUS booster

[Wesley Cheng]

Some Qualcomm PMICs have the capability to source the VBUS output to
connected peripherals.  This driver will register a regulator to the
regulator list to enable or disable this source by an external driver.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 drivers/regulator/Kconfig                   |  10 ++
 drivers/regulator/Makefile                  |   1 +
 drivers/regulator/qcom_usb_vbus-regulator.c | 147 ++++++++++++++++++++
 3 files changed, 158 insertions(+)
 create mode 100644 drivers/regulator/qcom_usb_vbus-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 074a2ef55943..f9165f9f9051 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -797,6 +797,16 @@ config REGULATOR_QCOM_SPMI
 	  Qualcomm SPMI PMICs as a module. The module will be named
 	  "qcom_spmi-regulator".
 
+config REGULATOR_QCOM_USB_VBUS
+	tristate "Qualcomm USB Vbus regulator driver"
+	depends on SPMI || COMPILE_TEST
+	help
+	  If you say yes to this option, support will be included for the
+	  regulator used to enable the VBUS output.
+
+	  Say M here if you want to include support for enabling the VBUS output
+	  as a module. The module will be named "qcom_usb-regulator".
+
 config REGULATOR_RC5T583
 	tristate "RICOH RC5T583 Power regulators"
 	depends on MFD_RC5T583
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index c0d6b96ebd78..cbab28aa7b56 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -89,6 +89,7 @@ obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
 obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
+obj-$(CONFIG_REGULATOR_QCOM_USB_VBUS) += qcom_usb_vbus-regulator.o
 obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
 obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
 obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o
diff --git a/drivers/regulator/qcom_usb_vbus-regulator.c b/drivers/regulator/qcom_usb_vbus-regulator.c
new file mode 100644
index 000000000000..2b8129a04684
--- /dev/null
+++ b/drivers/regulator/qcom_usb_vbus-regulator.c
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regmap.h>
+
+#define CMD_OTG				0x40
+#define OTG_EN				BIT(0)
+#define OTG_CFG				0x53
+#define OTG_EN_SRC_CFG			BIT(1)
+
+struct qcom_vbus {
+	struct device	*dev;
+	u32		base;
+	struct regmap	*regmap;
+	struct regulator_dev *usb_vbus_reg;
+};
+
+static int qcom_usb_vbus_enable(struct regulator_dev *rdev)
+{
+	struct qcom_vbus *vbus_out = rdev_get_drvdata(rdev);
+	int rc;
+
+	rc = regmap_update_bits(vbus_out->regmap, vbus_out->base + CMD_OTG,
+				OTG_EN, OTG_EN);
+	if (rc)
+		dev_err(vbus_out->dev, "failed to enable usb_vbus\n");
+
+	return rc;
+}
+
+static int qcom_usb_vbus_disable(struct regulator_dev *rdev)
+{
+	struct qcom_vbus *vbus_out = rdev_get_drvdata(rdev);
+	int rc;
+
+	rc = regmap_update_bits(vbus_out->regmap, vbus_out->base + CMD_OTG,
+				OTG_EN, 0);
+	if (rc)
+		dev_err(vbus_out->dev, "failed to disable usb_vbus\n");
+
+	return rc;
+}
+
+static int qcom_usb_vbus_is_enabled(struct regulator_dev *rdev)
+{
+	struct qcom_vbus *vbus_out = rdev_get_drvdata(rdev);
+	unsigned int value = 0;
+	int rc;
+
+	rc = regmap_read(vbus_out->regmap, vbus_out->base + CMD_OTG, &value);
+	if (rc)
+		dev_err(vbus_out->dev, "failed to read OTG_CTL\n");
+
+	return !!(value & OTG_EN);
+}
+
+static const struct regulator_ops qcom_usb_vbus_reg_ops = {
+	.enable = qcom_usb_vbus_enable,
+	.disable = qcom_usb_vbus_disable,
+	.is_enabled = qcom_usb_vbus_is_enabled,
+};
+
+static const struct regulator_desc qcom_usb_vbus_rdesc = {
+	.name = "usb_vbus",
+	.ops = &qcom_usb_vbus_reg_ops,
+	.owner = THIS_MODULE,
+	.type = REGULATOR_VOLTAGE,
+};
+
+static const struct of_device_id qcom_usb_vbus_regulator_match[] = {
+	{ .compatible = "qcom,pm8150b-vbus-reg" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_vbus_regulator_match);
+
+static int qcom_usb_vbus_regulator_probe(struct platform_device *pdev)
+{
+	struct qcom_vbus *vbus_out;
+	struct device *dev = &pdev->dev;
+	struct regulator_config config = { };
+	struct regulator_init_data init_data = { };
+	int ret;
+	u32 reg;
+
+	ret = of_property_read_u32(dev->of_node, "reg", &reg);
+	if (ret < 0) {
+		dev_err(dev, "no base address found\n");
+		return ret;
+	}
+
+	vbus_out = devm_kzalloc(dev, sizeof(vbus_out), GFP_KERNEL);
+	if (!vbus_out)
+		return -ENOMEM;
+	vbus_out->base = reg;
+	vbus_out->dev = dev;
+
+	vbus_out->regmap = dev_get_regmap(dev->parent, NULL);
+	if (!vbus_out->regmap) {
+		dev_err(dev, "Failed to get regmap\n");
+		return -ENOENT;
+	}
+
+	init_data.constraints.valid_ops_mask |= REGULATOR_CHANGE_STATUS;
+	config.dev = dev;
+	config.driver_data = vbus_out;
+	config.init_data = &init_data;
+
+	vbus_out->usb_vbus_reg = devm_regulator_register(dev,
+							 &qcom_usb_vbus_rdesc,
+							 &config);
+	if (IS_ERR(vbus_out->usb_vbus_reg)) {
+		ret = PTR_ERR(vbus_out->usb_vbus_reg);
+		dev_err(dev, "not able to register vbus reg %d\n", ret);
+		return ret;
+	}
+
+	/* Disable HW logic for VBUS enable */
+	regmap_update_bits(vbus_out->regmap, vbus_out->base + OTG_CFG,
+			   OTG_EN_SRC_CFG, 0);
+
+	return 0;
+}
+
+static struct platform_driver qcom_usb_vbus_regulator_driver = {
+	.driver		= {
+		.name	= "qcom-usb-vbus-regulator",
+		.of_match_table = qcom_usb_vbus_regulator_match,
+	},
+	.probe		= qcom_usb_vbus_regulator_probe,
+};
+module_platform_driver(qcom_usb_vbus_regulator_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB vbus regulator driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-usb-vbus-regulator");
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v2 5/6] dt-bindings: regulator: Add dt-binding for QCOM PMIC VBUS output regulator

[Wesley Cheng]

This describes how to enable the Qualcomm PMIC VBUS booster used for
providing power to connected USB peripherals when the USB role is host
mode.  The driver itself will register the vbus_usb regulator, so that
external drivers can utilize the enable/disable regulator APIs.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 .../regulator/qcom,usb-vbus-regulator.yaml    | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml

diff --git a/Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml
new file mode 100644
index 000000000000..2fa76111cfb9
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/qcom,usb-vbus-regulator.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/qcom,usb-vbus-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: The Qualcomm PMIC VBUS output regulator driver
+
+maintainers:
+  - Wesley Cheng <wcheng@codeaurora.org>
+
+description: |
+  This regulator driver controls the VBUS output by the Qualcomm PMIC.  This
+  regulator will be enabled in situations where the device is required to
+  provide power to the connected peripheral.
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm8150b-vbus-reg
+
+  reg:
+    maxItems: 1
+    description: VBUS output base address
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+     pm8150b {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        qcom,dcdc@1100 {
+            compatible = "qcom,pm8150b-vbus-reg";
+            reg = <0x1100>;
+        };
+     };
+...
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v2 6/6] arm64: boot: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster

[Wesley Cheng]

Add the required DTS node for the USB VBUS output regulator, which is
available on PM8150B.  This will provide the VBUS source to connected
peripherals.

Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
---
 arch/arm64/boot/dts/qcom/pm8150b.dtsi   | 6 ++++++
 arch/arm64/boot/dts/qcom/sm8150-mtp.dts | 7 +++++++
 2 files changed, 13 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
index ec44a8bc2f84..b7274d9d7341 100644
--- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -22,6 +22,12 @@ power-on@800 {
 			status = "disabled";
 		};
 
+		qcom,dcdc@1100 {
+			compatible = "qcom,pm8150b-vbus-reg";
+			status = "disabled";
+			reg = <0x1100>;
+		};
+
 		qcom,typec@1500 {
 			compatible = "qcom,pm8150b-usb-typec";
 			status = "disabled";
diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
index 6c6325c3af59..3845d19893eb 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
@@ -426,6 +426,13 @@ &usb_1 {
 	status = "okay";
 };
 
+&spmi_bus {
+	pmic@2 {
+		qcom,dcdc@1100 {
+			status = "okay";
+		};
+};
+
 &usb_1_dwc3 {
 	dr_mode = "peripheral";
 };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v2 4/6] regulator: Add support for QCOM PMIC VBUS booster

[Randy Dunlap]

On 6/12/20 4:19 PM, Wesley Cheng wrote:
> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> index 074a2ef55943..f9165f9f9051 100644
> --- a/drivers/regulator/Kconfig
> +++ b/drivers/regulator/Kconfig
> @@ -797,6 +797,16 @@ config REGULATOR_QCOM_SPMI
>  	  Qualcomm SPMI PMICs as a module. The module will be named
>  	  "qcom_spmi-regulator".
>  
> +config REGULATOR_QCOM_USB_VBUS
> +	tristate "Qualcomm USB Vbus regulator driver"
> +	depends on SPMI || COMPILE_TEST
> +	help
> +	  If you say yes to this option, support will be included for the
> +	  regulator used to enable the VBUS output.
> +
> +	  Say M here if you want to include support for enabling the VBUS output
> +	  as a module. The module will be named "qcom_usb-regulator".

Hi,
Shouldn't that module name match what is in the Makefile?


> +
>  config REGULATOR_RC5T583
>  	tristate "RICOH RC5T583 Power regulators"
>  	depends on MFD_RC5T583
> diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
> index c0d6b96ebd78..cbab28aa7b56 100644
> --- a/drivers/regulator/Makefile
> +++ b/drivers/regulator/Makefile
> @@ -89,6 +89,7 @@ obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
>  obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
>  obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
>  obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
> +obj-$(CONFIG_REGULATOR_QCOM_USB_VBUS) += qcom_usb_vbus-regulator.o
>  obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
>  obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
>  obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o


thanks.
-- 
~Randy

Re: [PATCH v2 4/6] regulator: Add support for QCOM PMIC VBUS booster

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 789 bytes --]

On Fri, Jun 12, 2020 at 04:19:16PM -0700, Wesley Cheng wrote:

> +++ b/drivers/regulator/qcom_usb_vbus-regulator.c
> @@ -0,0 +1,147 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
> + */

Please make the entire comment a C++ one so things look more
intentional.

> +static int qcom_usb_vbus_enable(struct regulator_dev *rdev)
> +{

> +static int qcom_usb_vbus_disable(struct regulator_dev *rdev)
> +{

> +static int qcom_usb_vbus_is_enabled(struct regulator_dev *rdev)
> +{

These operations can all be replaced by regulator_is_enabled_regmap()
and friends.

> +	init_data.constraints.valid_ops_mask |= REGULATOR_CHANGE_STATUS;

No, this is broken - regulators should not override the constraints the
machine sets.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v2 4/6] regulator: Add support for QCOM PMIC VBUS booster

[Wesley Cheng]

On 6/12/2020 8:28 PM, Randy Dunlap wrote:
> On 6/12/20 4:19 PM, Wesley Cheng wrote:
>> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
>> index 074a2ef55943..f9165f9f9051 100644
>> --- a/drivers/regulator/Kconfig
>> +++ b/drivers/regulator/Kconfig
>> @@ -797,6 +797,16 @@ config REGULATOR_QCOM_SPMI
>>  	  Qualcomm SPMI PMICs as a module. The module will be named
>>  	  "qcom_spmi-regulator".
>>  
>> +config REGULATOR_QCOM_USB_VBUS
>> +	tristate "Qualcomm USB Vbus regulator driver"
>> +	depends on SPMI || COMPILE_TEST
>> +	help
>> +	  If you say yes to this option, support will be included for the
>> +	  regulator used to enable the VBUS output.
>> +
>> +	  Say M here if you want to include support for enabling the VBUS output
>> +	  as a module. The module will be named "qcom_usb-regulator".
> 
> Hi,
> Shouldn't that module name match what is in the Makefile?
> 
> 

Thanks, Randy.  Missed this as I was going back and forth on the file
name.  Thanks for the catch.

>> +
>>  config REGULATOR_RC5T583
>>  	tristate "RICOH RC5T583 Power regulators"
>>  	depends on MFD_RC5T583
>> diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
>> index c0d6b96ebd78..cbab28aa7b56 100644
>> --- a/drivers/regulator/Makefile
>> +++ b/drivers/regulator/Makefile
>> @@ -89,6 +89,7 @@ obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
>>  obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
>>  obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
>>  obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
>> +obj-$(CONFIG_REGULATOR_QCOM_USB_VBUS) += qcom_usb_vbus-regulator.o
>>  obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
>>  obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
>>  obj-$(CONFIG_REGULATOR_PV88060) += pv88060-regulator.o
> 
> 
> thanks.
> 

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v2 4/6] regulator: Add support for QCOM PMIC VBUS booster

[Wesley Cheng]

On 6/15/2020 5:00 AM, Mark Brown wrote:
> On Fri, Jun 12, 2020 at 04:19:16PM -0700, Wesley Cheng wrote:
> 
>> +++ b/drivers/regulator/qcom_usb_vbus-regulator.c
>> @@ -0,0 +1,147 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
>> + */
> 
> Please make the entire comment a C++ one so things look more
> intentional.
> 

Hi Mark,

Sure, will do.

>> +static int qcom_usb_vbus_enable(struct regulator_dev *rdev)
>> +{
> 
>> +static int qcom_usb_vbus_disable(struct regulator_dev *rdev)
>> +{
> 
>> +static int qcom_usb_vbus_is_enabled(struct regulator_dev *rdev)
>> +{
> 
> These operations can all be replaced by regulator_is_enabled_regmap()
> and friends.
> 

Got it.  This simplifies the driver a lot.  Thanks for the tip.

>> +	init_data.constraints.valid_ops_mask |= REGULATOR_CHANGE_STATUS;
> 
> No, this is broken - regulators should not override the constraints the
> machine sets.
> 

Understood.  I decided to go with of_get_regulator_init_data() to
initialize the init_data parameter.  This should take care of the
constraint settings.


-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project