* [PATCH v4 1/3] net: phy: mscc: move shared probe code into a helper
2020-06-17 21:33 [PATCH v4 0/3] add clkout support to mscc phys Heiko Stuebner
@ 2020-06-17 21:33 ` Heiko Stuebner
2020-06-18 1:13 ` Andrew Lunn
2020-06-17 21:33 ` [PATCH v4 2/3] dt-bindings: net: ethernet-phy: add enet-phy-clock-out-frequency Heiko Stuebner
2020-06-17 21:33 ` [PATCH v4 3/3] net: phy: mscc: handle the clkout control on some phy variants Heiko Stuebner
2 siblings, 1 reply; 6+ messages in thread
From: Heiko Stuebner @ 2020-06-17 21:33 UTC (permalink / raw)
To: davem, kuba
Cc: robh+dt, andrew, f.fainelli, hkallweit1, linux, netdev,
devicetree, linux-kernel, heiko, christoph.muellner,
Heiko Stuebner
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
The different probe functions share a lot of code, so move the
common parts into a helper to reduce duplication.
This moves the devm_phy_package_join below the general allocation
but as all components just allocate things, this should be ok.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
drivers/net/phy/mscc/mscc_main.c | 124 +++++++++++++++----------------
1 file changed, 61 insertions(+), 63 deletions(-)
diff --git a/drivers/net/phy/mscc/mscc_main.c b/drivers/net/phy/mscc/mscc_main.c
index 5ddc44f87eaf..5d2777522fb4 100644
--- a/drivers/net/phy/mscc/mscc_main.c
+++ b/drivers/net/phy/mscc/mscc_main.c
@@ -1935,12 +1935,11 @@ static int vsc85xx_read_status(struct phy_device *phydev)
return genphy_read_status(phydev);
}
-static int vsc8514_probe(struct phy_device *phydev)
+static int vsc85xx_probe_helper(struct phy_device *phydev,
+ u32 *leds, int num_leds, u16 led_modes,
+ const struct vsc85xx_hw_stat *stats, int nstats)
{
struct vsc8531_private *vsc8531;
- u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
- VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
- VSC8531_DUPLEX_COLLISION};
vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
if (!vsc8531)
@@ -1948,54 +1947,66 @@ static int vsc8514_probe(struct phy_device *phydev)
phydev->priv = vsc8531;
- vsc8584_get_base_addr(phydev);
- devm_phy_package_join(&phydev->mdio.dev, phydev,
- vsc8531->base_addr, 0);
-
- vsc8531->nleds = 4;
- vsc8531->supp_led_modes = VSC85XX_SUPP_LED_MODES;
- vsc8531->hw_stats = vsc85xx_hw_stats;
- vsc8531->nstats = ARRAY_SIZE(vsc85xx_hw_stats);
+ vsc8531->nleds = num_leds;
+ vsc8531->supp_led_modes = led_modes;
+ vsc8531->hw_stats = stats;
+ vsc8531->nstats = nstats;
vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
sizeof(u64), GFP_KERNEL);
if (!vsc8531->stats)
return -ENOMEM;
- return vsc85xx_dt_led_modes_get(phydev, default_mode);
+ return vsc85xx_dt_led_modes_get(phydev, leds);
}
-static int vsc8574_probe(struct phy_device *phydev)
+static int vsc8514_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
+ int rc;
u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
VSC8531_DUPLEX_COLLISION};
- vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
- if (!vsc8531)
- return -ENOMEM;
-
- phydev->priv = vsc8531;
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC85XX_SUPP_LED_MODES,
+ vsc85xx_hw_stats,
+ ARRAY_SIZE(vsc85xx_hw_stats));
+ if (rc < 0)
+ return rc;
+ vsc8531 = phydev->priv;
vsc8584_get_base_addr(phydev);
- devm_phy_package_join(&phydev->mdio.dev, phydev,
- vsc8531->base_addr, 0);
+ return devm_phy_package_join(&phydev->mdio.dev, phydev,
+ vsc8531->base_addr, 0);
+}
- vsc8531->nleds = 4;
- vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
- vsc8531->hw_stats = vsc8584_hw_stats;
- vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
- vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
- sizeof(u64), GFP_KERNEL);
- if (!vsc8531->stats)
- return -ENOMEM;
+static int vsc8574_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ int rc;
+ u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
+ VSC8531_DUPLEX_COLLISION};
+
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC8584_SUPP_LED_MODES,
+ vsc8584_hw_stats,
+ ARRAY_SIZE(vsc8584_hw_stats));
+ if (rc < 0)
+ return rc;
- return vsc85xx_dt_led_modes_get(phydev, default_mode);
+ vsc8531 = phydev->priv;
+ vsc8584_get_base_addr(phydev);
+ return devm_phy_package_join(&phydev->mdio.dev, phydev,
+ vsc8531->base_addr, 0);
}
static int vsc8584_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
+ int rc;
u32 default_mode[4] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY, VSC8531_LINK_ACTIVITY,
VSC8531_DUPLEX_COLLISION};
@@ -2005,32 +2016,24 @@ static int vsc8584_probe(struct phy_device *phydev)
return -ENOTSUPP;
}
- vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
- if (!vsc8531)
- return -ENOMEM;
-
- phydev->priv = vsc8531;
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC8584_SUPP_LED_MODES,
+ vsc8584_hw_stats,
+ ARRAY_SIZE(vsc8584_hw_stats));
+ if (rc < 0)
+ return rc;
+ vsc8531 = phydev->priv;
vsc8584_get_base_addr(phydev);
- devm_phy_package_join(&phydev->mdio.dev, phydev,
- vsc8531->base_addr, 0);
-
- vsc8531->nleds = 4;
- vsc8531->supp_led_modes = VSC8584_SUPP_LED_MODES;
- vsc8531->hw_stats = vsc8584_hw_stats;
- vsc8531->nstats = ARRAY_SIZE(vsc8584_hw_stats);
- vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
- sizeof(u64), GFP_KERNEL);
- if (!vsc8531->stats)
- return -ENOMEM;
-
- return vsc85xx_dt_led_modes_get(phydev, default_mode);
+ return devm_phy_package_join(&phydev->mdio.dev, phydev,
+ vsc8531->base_addr, 0);
}
static int vsc85xx_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
- int rate_magic;
+ int rate_magic, rc;
u32 default_mode[2] = {VSC8531_LINK_1000_ACTIVITY,
VSC8531_LINK_100_ACTIVITY};
@@ -2038,23 +2041,18 @@ static int vsc85xx_probe(struct phy_device *phydev)
if (rate_magic < 0)
return rate_magic;
- vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL);
- if (!vsc8531)
- return -ENOMEM;
-
- phydev->priv = vsc8531;
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC85XX_SUPP_LED_MODES,
+ vsc85xx_hw_stats,
+ ARRAY_SIZE(vsc85xx_hw_stats));
+ if (rc < 0)
+ return rc;
+ vsc8531 = phydev->priv;
vsc8531->rate_magic = rate_magic;
- vsc8531->nleds = 2;
- vsc8531->supp_led_modes = VSC85XX_SUPP_LED_MODES;
- vsc8531->hw_stats = vsc85xx_hw_stats;
- vsc8531->nstats = ARRAY_SIZE(vsc85xx_hw_stats);
- vsc8531->stats = devm_kcalloc(&phydev->mdio.dev, vsc8531->nstats,
- sizeof(u64), GFP_KERNEL);
- if (!vsc8531->stats)
- return -ENOMEM;
- return vsc85xx_dt_led_modes_get(phydev, default_mode);
+ return 0;
}
/* Microsemi VSC85xx PHYs */
--
2.26.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v4 1/3] net: phy: mscc: move shared probe code into a helper
2020-06-17 21:33 ` [PATCH v4 1/3] net: phy: mscc: move shared probe code into a helper Heiko Stuebner
@ 2020-06-18 1:13 ` Andrew Lunn
0 siblings, 0 replies; 6+ messages in thread
From: Andrew Lunn @ 2020-06-18 1:13 UTC (permalink / raw)
To: Heiko Stuebner
Cc: davem, kuba, robh+dt, f.fainelli, hkallweit1, linux, netdev,
devicetree, linux-kernel, christoph.muellner, Heiko Stuebner
On Wed, Jun 17, 2020 at 11:33:24PM +0200, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
>
> The different probe functions share a lot of code, so move the
> common parts into a helper to reduce duplication.
>
> This moves the devm_phy_package_join below the general allocation
> but as all components just allocate things, this should be ok.
>
> Suggested-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Andrew
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v4 2/3] dt-bindings: net: ethernet-phy: add enet-phy-clock-out-frequency
2020-06-17 21:33 [PATCH v4 0/3] add clkout support to mscc phys Heiko Stuebner
2020-06-17 21:33 ` [PATCH v4 1/3] net: phy: mscc: move shared probe code into a helper Heiko Stuebner
@ 2020-06-17 21:33 ` Heiko Stuebner
2020-06-17 21:59 ` Heiko Stübner
2020-06-17 21:33 ` [PATCH v4 3/3] net: phy: mscc: handle the clkout control on some phy variants Heiko Stuebner
2 siblings, 1 reply; 6+ messages in thread
From: Heiko Stuebner @ 2020-06-17 21:33 UTC (permalink / raw)
To: davem, kuba
Cc: robh+dt, andrew, f.fainelli, hkallweit1, linux, netdev,
devicetree, linux-kernel, heiko, christoph.muellner,
Heiko Stuebner
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Some ethernet phys have a configurable clock output, so add a generic
property to describe its target rate.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
Documentation/devicetree/bindings/net/ethernet-phy.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
index 9b1f1147ca36..4dcf93f1c555 100644
--- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
+++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
@@ -84,6 +84,11 @@ properties:
the turn around line low at end of the control phase of the
MDIO transaction.
+ enet-phy-clock-out-frequency:
+ $ref: /schemas/types.yaml#definitions/uint32
+ description:
+ Frequency in Hz to set an available clock output to.
+
enet-phy-lane-swap:
$ref: /schemas/types.yaml#definitions/flag
description:
--
2.26.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v4 2/3] dt-bindings: net: ethernet-phy: add enet-phy-clock-out-frequency
2020-06-17 21:33 ` [PATCH v4 2/3] dt-bindings: net: ethernet-phy: add enet-phy-clock-out-frequency Heiko Stuebner
@ 2020-06-17 21:59 ` Heiko Stübner
0 siblings, 0 replies; 6+ messages in thread
From: Heiko Stübner @ 2020-06-17 21:59 UTC (permalink / raw)
To: davem
Cc: kuba, robh+dt, andrew, f.fainelli, hkallweit1, linux, netdev,
devicetree, linux-kernel, christoph.muellner
Am Mittwoch, 17. Juni 2020, 23:33:25 CEST schrieb Heiko Stuebner:
> From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
>
> Some ethernet phys have a configurable clock output, so add a generic
> property to describe its target rate.
>
> Suggested-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
just now Rob wrote for v3:
----- 8< ------
The correct thing to do here is make the phy a clock provider and then
the client side use 'assigned-clock-rate' to set the rate. That has the
advantage that it also describes the connection of the clock signal. You
might not need that for a simple case, but I could imagine needing that
in a more complex case.
Rob
----- 8< ------
> Documentation/devicetree/bindings/net/ethernet-phy.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> index 9b1f1147ca36..4dcf93f1c555 100644
> --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> @@ -84,6 +84,11 @@ properties:
> the turn around line low at end of the control phase of the
> MDIO transaction.
>
> + enet-phy-clock-out-frequency:
> + $ref: /schemas/types.yaml#definitions/uint32
> + description:
> + Frequency in Hz to set an available clock output to.
> +
> enet-phy-lane-swap:
> $ref: /schemas/types.yaml#definitions/flag
> description:
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v4 3/3] net: phy: mscc: handle the clkout control on some phy variants
2020-06-17 21:33 [PATCH v4 0/3] add clkout support to mscc phys Heiko Stuebner
2020-06-17 21:33 ` [PATCH v4 1/3] net: phy: mscc: move shared probe code into a helper Heiko Stuebner
2020-06-17 21:33 ` [PATCH v4 2/3] dt-bindings: net: ethernet-phy: add enet-phy-clock-out-frequency Heiko Stuebner
@ 2020-06-17 21:33 ` Heiko Stuebner
2 siblings, 0 replies; 6+ messages in thread
From: Heiko Stuebner @ 2020-06-17 21:33 UTC (permalink / raw)
To: davem, kuba
Cc: robh+dt, andrew, f.fainelli, hkallweit1, linux, netdev,
devicetree, linux-kernel, heiko, christoph.muellner,
Heiko Stuebner
From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
At least VSC8530/8531/8540/8541 contain a clock output that can emit
a predefined rate of 25, 50 or 125MHz.
This may then feed back into the network interface as source clock.
So follow the example the at803x already set and introduce a
vsc8531,clk-out-frequency property to set that output.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
---
drivers/net/phy/mscc/mscc.h | 9 ++++
drivers/net/phy/mscc/mscc_main.c | 87 +++++++++++++++++++++++++++++---
2 files changed, 89 insertions(+), 7 deletions(-)
diff --git a/drivers/net/phy/mscc/mscc.h b/drivers/net/phy/mscc/mscc.h
index fbcee5fce7b2..a3afc35c3eab 100644
--- a/drivers/net/phy/mscc/mscc.h
+++ b/drivers/net/phy/mscc/mscc.h
@@ -218,6 +218,13 @@ enum rgmii_clock_delay {
#define INT_MEM_DATA_M 0x00ff
#define INT_MEM_DATA(x) (INT_MEM_DATA_M & (x))
+#define MSCC_CLKOUT_CNTL 13
+#define CLKOUT_ENABLE BIT(15)
+#define CLKOUT_FREQ_MASK GENMASK(14, 13)
+#define CLKOUT_FREQ_25M (0x0 << 13)
+#define CLKOUT_FREQ_50M (0x1 << 13)
+#define CLKOUT_FREQ_125M (0x2 << 13)
+
#define MSCC_PHY_PROC_CMD 18
#define PROC_CMD_NCOMPLETED 0x8000
#define PROC_CMD_FAILED 0x4000
@@ -360,6 +367,8 @@ struct vsc8531_private {
*/
unsigned int base_addr;
+ u32 clkout_rate;
+
#if IS_ENABLED(CONFIG_MACSEC)
/* MACsec fields:
* - One SecY per device (enforced at the s/w implementation level)
diff --git a/drivers/net/phy/mscc/mscc_main.c b/drivers/net/phy/mscc/mscc_main.c
index 5d2777522fb4..2f06cfa2f539 100644
--- a/drivers/net/phy/mscc/mscc_main.c
+++ b/drivers/net/phy/mscc/mscc_main.c
@@ -432,6 +432,18 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
return led_mode;
}
+static void vsc8531_dt_clkout_rate_get(struct phy_device *phydev)
+{
+ struct vsc8531_private *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ struct device_node *of_node = dev->of_node;
+
+ if (!of_node)
+ return;
+
+ of_property_read_u32(of_node, "enet-phy-clock-out-frequency",
+ &priv->clkout_rate);
+}
#else
static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
{
@@ -444,6 +456,10 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
{
return default_mode;
}
+
+static void vsc8531_dt_clkout_rate_get(struct phy_device *phydev)
+{
+}
#endif /* CONFIG_OF_MDIO */
static int vsc85xx_dt_led_modes_get(struct phy_device *phydev,
@@ -1508,6 +1524,37 @@ static int vsc85xx_config_init(struct phy_device *phydev)
return 0;
}
+static int vsc8531_config_init(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531 = phydev->priv;
+ u16 val;
+ int rc;
+
+ rc = vsc85xx_config_init(phydev);
+ if (rc)
+ return rc;
+
+ switch (vsc8531->clkout_rate) {
+ case 0:
+ val = 0;
+ break;
+ case 25000000:
+ val = CLKOUT_FREQ_25M | CLKOUT_ENABLE;
+ break;
+ case 50000000:
+ val = CLKOUT_FREQ_50M | CLKOUT_ENABLE;
+ break;
+ case 125000000:
+ val = CLKOUT_FREQ_125M | CLKOUT_ENABLE;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return phy_write_paged(phydev, MSCC_PHY_PAGE_EXTENDED_GPIO,
+ MSCC_CLKOUT_CNTL, val);
+}
+
static int vsc8584_did_interrupt(struct phy_device *phydev)
{
int rc = 0;
@@ -1981,6 +2028,32 @@ static int vsc8514_probe(struct phy_device *phydev)
vsc8531->base_addr, 0);
}
+static int vsc8531_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ int rate_magic, rc;
+ u32 default_mode[2] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY};
+
+ rate_magic = vsc85xx_edge_rate_magic_get(phydev);
+ if (rate_magic < 0)
+ return rate_magic;
+
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC85XX_SUPP_LED_MODES,
+ vsc85xx_hw_stats,
+ ARRAY_SIZE(vsc85xx_hw_stats));
+ if (rc < 0)
+ return rc;
+
+ vsc8531 = phydev->priv;
+ vsc8531->rate_magic = rate_magic;
+ vsc8531_dt_clkout_rate_get(phydev);
+
+ return 0;
+}
+
static int vsc8574_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
@@ -2136,14 +2209,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2160,14 +2233,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2184,14 +2257,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2208,7 +2281,7 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
--
2.26.2
^ permalink raw reply related [flat|nested] 6+ messages in thread