From: Jonathan McDowell <noodles@earth.li>
To: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>,
Vivien Didelot <vivien.didelot@gmail.com>,
David Miller <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Russell King - ARM Linux admin <linux@armlinux.org.uk>,
Matthew Hagan <mnhagan88@gmail.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [RFC PATCH] net: dsa: qca8k: Add 802.1q VLAN support
Date: Wed, 22 Jul 2020 20:38:50 +0100 [thread overview]
Message-ID: <20200722193850.GM23489@earth.li> (raw)
In-Reply-To: <1bf941f5-fdb3-3d9b-627a-a0464787b0ab@gmail.com>
On Tue, Jul 21, 2020 at 10:26:07AM -0700, Florian Fainelli wrote:
> On 7/21/20 10:16 AM, Jonathan McDowell wrote:
> > This adds full 802.1q VLAN support to the qca8k, allowing the use of
> > vlan_filtering and more complicated bridging setups than allowed by
> > basic port VLAN support.
> >
> > Tested with a number of untagged ports with separate VLANs and then a
> > trunk port with all the VLANs tagged on it.
>
> This looks good to me at first glance, at least not seeing obvious
> issue, however below are a few questions:
Thanks for the comments.
> - vid == 0 appears to be unsupported according to your port_vlan_prepare
> callback, is this really the case, or is it more a case of VID 0 should
> be pvid untagged, which is what dsa_slave_vlan_rx_add_vid() would
> attempt to program
I don't quite follow you here. VID 0 doesn't appear to be supported by
the hardware (and several other DSA drivers don't seem to like it
either), hence the check; I'm not clear if there's something alternate I
should be doing in that case instead?
> - since we have a qca8k_port_bridge_join() callback which programs the
> port lookup control register, putting all ports by default in VID==1
> does not break per-port isolation between non-bridged and bridged ports,
> right?
VLAN_MODE_NONE (set when we don't have VLAN filtering enabled)
configures us for port filtering, ignoring the VLAN info, so I think
we're good here.
> - since you program the ports with a default VLAN ID upon startup of the
> switch driver should not you also set
> dsa_switch::configure_vlan_while_not_filtering to indicate to the DSA
> layer that there is a VLAN table programmed regardless of VLAN filtering
> being enabled in the bridge or not?
Yup, this should be set. I'd seen the vlan_bridge_vtu patch from
December but not noticed it had been renamed, just assumed it hadn't
been applied.
> See some nitpicks below:
>
> >
> > Signed-off-by: Jonathan McDowell <noodles@earth.li>
> >
> > diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> > index a5566de82853..cce05493075f 100644
> > --- a/drivers/net/dsa/qca8k.c
> > +++ b/drivers/net/dsa/qca8k.c
> > @@ -408,6 +408,104 @@ qca8k_fdb_flush(struct qca8k_priv *priv)
> > mutex_unlock(&priv->reg_mutex);
> > }
> >
> > +static int
> > +qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid)
> > +{
> > + u32 reg;
> > +
> > + /* Set the command and VLAN index */
> > + reg = QCA8K_VTU_FUNC1_BUSY;> + reg |= cmd;
> > + reg |= vid << QCA8K_VTU_FUNC1_VID_S;
> > +
> > + /* Write the function register triggering the table access */
> > + qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg);
> > +
> > + /* wait for completion */
> > + if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY))
> > + return -1;
>
> Can you propagate the return value from qca8k_busy_wait() directly?
It just returns a boolean. rmk makes a valid point about a sensible
errno instead, so I'll switch to ETIMEDOUT in v2 (and ENOMEM when the
VLAN table is full below).
> > +
> > + /* Check for table full violation when adding an entry */
> > + if (cmd == QCA8K_VLAN_LOAD) {
> > + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1);
> > + if (reg & QCA8K_VTU_FUNC1_FULL)
> > + return -1;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int
> > +qca8k_vlan_add(struct qca8k_priv *priv, u8 port, u16 vid, bool tagged)
> > +{
> > + u32 reg;
> > + int ret;
> > +
> > + if (!vid)
> > + return -EOPNOTSUPP;
> > +
> > + mutex_lock(&priv->reg_mutex);
> > + ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
> > + if (ret >= 0) {
>
> Do an early return upon negative error code instead of reidenting the
> code block?
I'll switch over to a goto for cleanup (unlocking the mutex) to avoid
the extra indentation (and below).
> > + reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0);
> > + reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN;
> > + reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port));
> > + if (tagged)
> > + reg |= QCA8K_VTU_FUNC0_EG_MODE_TAG <<
> > + QCA8K_VTU_FUNC0_EG_MODE_S(port);
> > + else
> > + reg |= QCA8K_VTU_FUNC0_EG_MODE_UNTAG <<
> > + QCA8K_VTU_FUNC0_EG_MODE_S(port);
> > +
> > + qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
> > + ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
> > + }
> > + mutex_unlock(&priv->reg_mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static int
> > +qca8k_vlan_del(struct qca8k_priv *priv, u8 port, u16 vid)
> > +{
> > + u32 reg;
> > + u32 mask;
> > + int ret;
> > + int i;
> > + bool del;
> > +
> > + mutex_lock(&priv->reg_mutex);
> > + ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
> > + if (ret >= 0) {
>
> Likewise
J.
--
"Editing plain text configuration files has never been the Unix way,
and vi certainly isn't a standard unix tool." - mjg59, QOOC.
next prev parent reply other threads:[~2020-07-22 19:38 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-21 17:16 [RFC PATCH] net: dsa: qca8k: Add 802.1q VLAN support Jonathan McDowell
2020-07-21 17:26 ` Florian Fainelli
2020-07-22 19:38 ` Jonathan McDowell [this message]
2020-07-22 22:36 ` Florian Fainelli
2020-07-22 22:58 ` Vladimir Oltean
2020-07-25 17:35 ` Jonathan McDowell
2020-07-21 20:48 ` Russell King - ARM Linux admin
2020-07-22 19:33 ` Jonathan McDowell
2020-07-26 14:56 ` [PATCH net-next v2] " Jonathan McDowell
2020-07-28 16:34 ` Vladimir Oltean
2020-07-30 10:40 ` Jonathan McDowell
2020-07-30 21:10 ` Vladimir Oltean
2020-08-01 17:05 ` [PATCH net-next v3 1/2] net: dsa: qca8k: Add define for port VID Jonathan McDowell
2020-08-01 20:48 ` Florian Fainelli
2020-08-02 13:21 ` Vladimir Oltean
2020-08-03 22:45 ` David Miller
2020-08-01 17:06 ` [PATCH net-next v3 2/2] net: dsa: qca8k: Add 802.1q VLAN support Jonathan McDowell
2020-08-01 20:50 ` Florian Fainelli
2020-08-02 13:21 ` Vladimir Oltean
2020-08-03 22:46 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200722193850.GM23489@earth.li \
--to=noodles@earth.li \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mnhagan88@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).