From: Jonathan McDowell <noodles@earth.li>
To: Andrew Lunn <andrew@lunn.ch>,
Vivien Didelot <vivien.didelot@gmail.com>,
Florian Fainelli <f.fainelli@gmail.com>,
Vladimir Oltean <olteanv@gmail.com>,
David Miller <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Russell King - ARM Linux admin <linux@armlinux.org.uk>,
Matthew Hagan <mnhagan88@gmail.com>,
netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH net-next v3 2/2] net: dsa: qca8k: Add 802.1q VLAN support
Date: Sat, 1 Aug 2020 18:06:46 +0100 [thread overview]
Message-ID: <ec320e8e5a9691b85ee79f6ef03f1b0b6a562655.1596301468.git.noodles@earth.li> (raw)
In-Reply-To: <20200721171624.GK23489@earth.li>
This adds full 802.1q VLAN support to the qca8k, allowing the use of
vlan_filtering and more complicated bridging setups than allowed by
basic port VLAN support.
Tested with a number of untagged ports with separate VLANs and then a
trunk port with all the VLANs tagged on it.
v3:
- Pull QCA8K_PORT_VID_DEF changes into separate cleanup patch
- Reverse Christmas tree notation for variable definitions
- Use untagged instead of tagged for consistency
v2:
- Return sensible errnos on failure rather than -1 (rmk)
- Style cleanups based on Florian's feedback
- Silently allow VLAN 0 as device correctly treats this as no tag
Signed-off-by: Jonathan McDowell <noodles@earth.li>
---
drivers/net/dsa/qca8k.c | 181 ++++++++++++++++++++++++++++++++++++++++
drivers/net/dsa/qca8k.h | 27 ++++++
2 files changed, 208 insertions(+)
diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index 3ebc4da63074..f1e484477e35 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -408,6 +408,112 @@ qca8k_fdb_flush(struct qca8k_priv *priv)
mutex_unlock(&priv->reg_mutex);
}
+static int
+qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid)
+{
+ u32 reg;
+
+ /* Set the command and VLAN index */
+ reg = QCA8K_VTU_FUNC1_BUSY;
+ reg |= cmd;
+ reg |= vid << QCA8K_VTU_FUNC1_VID_S;
+
+ /* Write the function register triggering the table access */
+ qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg);
+
+ /* wait for completion */
+ if (qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY))
+ return -ETIMEDOUT;
+
+ /* Check for table full violation when adding an entry */
+ if (cmd == QCA8K_VLAN_LOAD) {
+ reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC1);
+ if (reg & QCA8K_VTU_FUNC1_FULL)
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int
+qca8k_vlan_add(struct qca8k_priv *priv, u8 port, u16 vid, bool untagged)
+{
+ u32 reg;
+ int ret;
+
+ /*
+ We do the right thing with VLAN 0 and treat it as untagged while
+ preserving the tag on egress.
+ */
+ if (vid == 0)
+ return 0;
+
+ mutex_lock(&priv->reg_mutex);
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
+ if (ret < 0)
+ goto out;
+
+ reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0);
+ reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN;
+ reg &= ~(QCA8K_VTU_FUNC0_EG_MODE_MASK << QCA8K_VTU_FUNC0_EG_MODE_S(port));
+ if (untagged)
+ reg |= QCA8K_VTU_FUNC0_EG_MODE_UNTAG <<
+ QCA8K_VTU_FUNC0_EG_MODE_S(port);
+ else
+ reg |= QCA8K_VTU_FUNC0_EG_MODE_TAG <<
+ QCA8K_VTU_FUNC0_EG_MODE_S(port);
+
+ qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
+
+out:
+ mutex_unlock(&priv->reg_mutex);
+
+ return ret;
+}
+
+static int
+qca8k_vlan_del(struct qca8k_priv *priv, u8 port, u16 vid)
+{
+ u32 reg, mask;
+ int ret, i;
+ bool del;
+
+ mutex_lock(&priv->reg_mutex);
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid);
+ if (ret < 0)
+ goto out;
+
+ reg = qca8k_read(priv, QCA8K_REG_VTU_FUNC0);
+ reg &= ~(3 << QCA8K_VTU_FUNC0_EG_MODE_S(port));
+ reg |= QCA8K_VTU_FUNC0_EG_MODE_NOT <<
+ QCA8K_VTU_FUNC0_EG_MODE_S(port);
+
+ /* Check if we're the last member to be removed */
+ del = true;
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
+ mask = QCA8K_VTU_FUNC0_EG_MODE_NOT;
+ mask <<= QCA8K_VTU_FUNC0_EG_MODE_S(i);
+
+ if ((reg & mask) != mask) {
+ del = false;
+ break;
+ }
+ }
+
+ if (del) {
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid);
+ } else {
+ qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg);
+ ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid);
+ }
+
+out:
+ mutex_unlock(&priv->reg_mutex);
+
+ return ret;
+}
+
static void
qca8k_mib_init(struct qca8k_priv *priv)
{
@@ -1187,6 +1293,76 @@ qca8k_port_fdb_dump(struct dsa_switch *ds, int port,
return 0;
}
+static int
+qca8k_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering)
+{
+ struct qca8k_priv *priv = ds->priv;
+
+ if (vlan_filtering) {
+ qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
+ QCA8K_PORT_LOOKUP_VLAN_MODE,
+ QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE);
+ } else {
+ qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
+ QCA8K_PORT_LOOKUP_VLAN_MODE,
+ QCA8K_PORT_LOOKUP_VLAN_MODE_NONE);
+ }
+
+ return 0;
+}
+
+static int
+qca8k_port_vlan_prepare(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ return 0;
+}
+
+static void
+qca8k_port_vlan_add(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
+ bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
+ struct qca8k_priv *priv = ds->priv;
+ int ret = 0;
+ u16 vid;
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end && !ret; ++vid)
+ ret = qca8k_vlan_add(priv, port, vid, untagged);
+
+ if (ret)
+ dev_err(priv->dev, "Failed to add VLAN to port %d (%d)", port, ret);
+
+ if (pvid) {
+ int shift = 16 * (port % 2);
+
+ qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port),
+ 0xfff << shift,
+ vlan->vid_end << shift);
+ qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port),
+ QCA8K_PORT_VLAN_CVID(vlan->vid_end) |
+ QCA8K_PORT_VLAN_SVID(vlan->vid_end));
+ }
+}
+
+static int
+qca8k_port_vlan_del(struct dsa_switch *ds, int port,
+ const struct switchdev_obj_port_vlan *vlan)
+{
+ struct qca8k_priv *priv = ds->priv;
+ int ret = 0;
+ u16 vid;
+
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end && !ret; ++vid)
+ ret = qca8k_vlan_del(priv, port, vid);
+
+ if (ret)
+ dev_err(priv->dev, "Failed to delete VLAN from port %d (%d)", port, ret);
+
+ return ret;
+}
+
static enum dsa_tag_protocol
qca8k_get_tag_protocol(struct dsa_switch *ds, int port,
enum dsa_tag_protocol mp)
@@ -1212,6 +1388,10 @@ static const struct dsa_switch_ops qca8k_switch_ops = {
.port_fdb_add = qca8k_port_fdb_add,
.port_fdb_del = qca8k_port_fdb_del,
.port_fdb_dump = qca8k_port_fdb_dump,
+ .port_vlan_filtering = qca8k_port_vlan_filtering,
+ .port_vlan_prepare = qca8k_port_vlan_prepare,
+ .port_vlan_add = qca8k_port_vlan_add,
+ .port_vlan_del = qca8k_port_vlan_del,
.phylink_validate = qca8k_phylink_validate,
.phylink_mac_link_state = qca8k_phylink_mac_link_state,
.phylink_mac_config = qca8k_phylink_mac_config,
@@ -1262,6 +1442,7 @@ qca8k_sw_probe(struct mdio_device *mdiodev)
priv->ds->dev = &mdiodev->dev;
priv->ds->num_ports = QCA8K_NUM_PORTS;
+ priv->ds->configure_vlan_while_not_filtering = true;
priv->ds->priv = priv;
priv->ops = qca8k_switch_ops;
priv->ds->ops = &priv->ops;
diff --git a/drivers/net/dsa/qca8k.h b/drivers/net/dsa/qca8k.h
index 92216a52daa5..7ca4b93e0bb5 100644
--- a/drivers/net/dsa/qca8k.h
+++ b/drivers/net/dsa/qca8k.h
@@ -128,6 +128,19 @@
#define QCA8K_ATU_FUNC_FULL BIT(12)
#define QCA8K_ATU_FUNC_PORT_M 0xf
#define QCA8K_ATU_FUNC_PORT_S 8
+#define QCA8K_REG_VTU_FUNC0 0x610
+#define QCA8K_VTU_FUNC0_VALID BIT(20)
+#define QCA8K_VTU_FUNC0_IVL_EN BIT(19)
+#define QCA8K_VTU_FUNC0_EG_MODE_S(_i) (4 + (_i) * 2)
+#define QCA8K_VTU_FUNC0_EG_MODE_MASK 3
+#define QCA8K_VTU_FUNC0_EG_MODE_UNMOD 0
+#define QCA8K_VTU_FUNC0_EG_MODE_UNTAG 1
+#define QCA8K_VTU_FUNC0_EG_MODE_TAG 2
+#define QCA8K_VTU_FUNC0_EG_MODE_NOT 3
+#define QCA8K_REG_VTU_FUNC1 0x614
+#define QCA8K_VTU_FUNC1_BUSY BIT(31)
+#define QCA8K_VTU_FUNC1_VID_S 16
+#define QCA8K_VTU_FUNC1_FULL BIT(4)
#define QCA8K_REG_GLOBAL_FW_CTRL0 0x620
#define QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN BIT(10)
#define QCA8K_REG_GLOBAL_FW_CTRL1 0x624
@@ -137,6 +150,11 @@
#define QCA8K_GLOBAL_FW_CTRL1_UC_DP_S 0
#define QCA8K_PORT_LOOKUP_CTRL(_i) (0x660 + (_i) * 0xc)
#define QCA8K_PORT_LOOKUP_MEMBER GENMASK(6, 0)
+#define QCA8K_PORT_LOOKUP_VLAN_MODE GENMASK(9, 8)
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_NONE (0 << 8)
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_FALLBACK (1 << 8)
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_CHECK (2 << 8)
+#define QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE (3 << 8)
#define QCA8K_PORT_LOOKUP_STATE_MASK GENMASK(18, 16)
#define QCA8K_PORT_LOOKUP_STATE_DISABLED (0 << 16)
#define QCA8K_PORT_LOOKUP_STATE_BLOCKING (1 << 16)
@@ -180,6 +198,15 @@ enum qca8k_fdb_cmd {
QCA8K_FDB_SEARCH = 7,
};
+enum qca8k_vlan_cmd {
+ QCA8K_VLAN_FLUSH = 1,
+ QCA8K_VLAN_LOAD = 2,
+ QCA8K_VLAN_PURGE = 3,
+ QCA8K_VLAN_REMOVE_PORT = 4,
+ QCA8K_VLAN_NEXT = 5,
+ QCA8K_VLAN_READ = 6,
+};
+
struct ar8xxx_port_status {
int enabled;
};
--
2.20.1
next prev parent reply other threads:[~2020-08-01 17:06 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-21 17:16 [RFC PATCH] net: dsa: qca8k: Add 802.1q VLAN support Jonathan McDowell
2020-07-21 17:26 ` Florian Fainelli
2020-07-22 19:38 ` Jonathan McDowell
2020-07-22 22:36 ` Florian Fainelli
2020-07-22 22:58 ` Vladimir Oltean
2020-07-25 17:35 ` Jonathan McDowell
2020-07-21 20:48 ` Russell King - ARM Linux admin
2020-07-22 19:33 ` Jonathan McDowell
2020-07-26 14:56 ` [PATCH net-next v2] " Jonathan McDowell
2020-07-28 16:34 ` Vladimir Oltean
2020-07-30 10:40 ` Jonathan McDowell
2020-07-30 21:10 ` Vladimir Oltean
2020-08-01 17:05 ` [PATCH net-next v3 1/2] net: dsa: qca8k: Add define for port VID Jonathan McDowell
2020-08-01 20:48 ` Florian Fainelli
2020-08-02 13:21 ` Vladimir Oltean
2020-08-03 22:45 ` David Miller
2020-08-01 17:06 ` Jonathan McDowell [this message]
2020-08-01 20:50 ` [PATCH net-next v3 2/2] net: dsa: qca8k: Add 802.1q VLAN support Florian Fainelli
2020-08-02 13:21 ` Vladimir Oltean
2020-08-03 22:46 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ec320e8e5a9691b85ee79f6ef03f1b0b6a562655.1596301468.git.noodles@earth.li \
--to=noodles@earth.li \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mnhagan88@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=olteanv@gmail.com \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).