* [PATCH 1/4] dt-bindings: regulator: Convert mp886x to json-schema
2020-07-28 15:23 [PATCH 0/4] regulator: mp886x: two features and dt json convert Jisheng Zhang
@ 2020-07-28 15:24 ` Jisheng Zhang
2020-07-28 15:45 ` Mark Brown
2020-07-28 15:24 ` [PATCH 2/4] regulator: mp886x: implement set_ramp_delay Jisheng Zhang
` (3 subsequent siblings)
4 siblings, 1 reply; 7+ messages in thread
From: Jisheng Zhang @ 2020-07-28 15:24 UTC (permalink / raw)
To: Liam Girdwood, Mark Brown, Rob Herring, Saravanan Sekar
Cc: linux-kernel, devicetree
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Convert the mp886x binding to DT schema format using json-schema.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
.../devicetree/bindings/regulator/mp886x.txt | 27 ----------
.../bindings/regulator/mps,mp886x.yaml | 53 +++++++++++++++++++
2 files changed, 53 insertions(+), 27 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/regulator/mp886x.txt
create mode 100644 Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
diff --git a/Documentation/devicetree/bindings/regulator/mp886x.txt b/Documentation/devicetree/bindings/regulator/mp886x.txt
deleted file mode 100644
index 551867829459..000000000000
--- a/Documentation/devicetree/bindings/regulator/mp886x.txt
+++ /dev/null
@@ -1,27 +0,0 @@
-Monolithic Power Systems MP8867/MP8869 voltage regulator
-
-Required properties:
-- compatible: Must be one of the following.
- "mps,mp8867"
- "mps,mp8869"
-- reg: I2C slave address.
-- enable-gpios: enable gpios.
-- mps,fb-voltage-divider: An array of two integers containing the resistor
- values R1 and R2 of the feedback voltage divider in kilo ohms.
-
-Any property defined as part of the core regulator binding, defined in
-./regulator.txt, can also be used.
-
-Example:
-
- vcpu: regulator@62 {
- compatible = "mps,mp8869";
- regulator-name = "vcpu";
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <850000>;
- regulator-always-on;
- regulator-boot-on;
- enable-gpios = <&porta 1 GPIO_ACTIVE_LOW>;
- mps,fb-voltage-divider = <80 240>;
- reg = <0x62>;
- };
diff --git a/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml b/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
new file mode 100644
index 000000000000..500a7b3a59aa
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/mps,mp886x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Monolithic Power Systems MP8867/MP8869 voltage regulator
+
+maintainers:
+ - Jisheng Zhang <jszhang@kernel.org>
+
+properties:
+ compatible:
+ enum:
+ - mps,mp8867
+ - mps,mp8869
+
+ reg:
+ maxItems: 1
+
+ enable-gpios:
+ description: GPIO to enable/disable the regulator.
+ maxItems: 1
+
+ mps,fb-voltage-divider:
+ description: An array of two integers containing the resistor
+ values R1 and R2 of the feedback voltage divider in kilo ohms.
+ $ref: "/schemas/types.yaml#/definitions/uint32-array"
+
+required:
+ - compatible
+ - reg
+ - enable-gpios
+ - mps,fb-voltage-divider
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ regulator@62 {
+ compatible = "mps,mp8869";
+ regulator-name = "vcpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ enable-gpios = <&porta 1 GPIO_ACTIVE_LOW>;
+ mps,fb-voltage-divider = <80 240>;
+ reg = <0x62>;
+ };
+ };
+
+...
--
2.28.0.rc0
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH 1/4] dt-bindings: regulator: Convert mp886x to json-schema
2020-07-28 15:24 ` [PATCH 1/4] dt-bindings: regulator: Convert mp886x to json-schema Jisheng Zhang
@ 2020-07-28 15:45 ` Mark Brown
0 siblings, 0 replies; 7+ messages in thread
From: Mark Brown @ 2020-07-28 15:45 UTC (permalink / raw)
To: Jisheng Zhang
Cc: Liam Girdwood, Rob Herring, Saravanan Sekar, linux-kernel, devicetree
[-- Attachment #1: Type: text/plain, Size: 363 bytes --]
On Tue, Jul 28, 2020 at 11:24:17PM +0800, Jisheng Zhang wrote:
> From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
>
> Convert the mp886x binding to DT schema format using json-schema.
Please put any schema conversions at the end of the series if they're in
one - there's often a backlog on review of them so it means they don't
hold up any other work.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 2/4] regulator: mp886x: implement set_ramp_delay
2020-07-28 15:23 [PATCH 0/4] regulator: mp886x: two features and dt json convert Jisheng Zhang
2020-07-28 15:24 ` [PATCH 1/4] dt-bindings: regulator: Convert mp886x to json-schema Jisheng Zhang
@ 2020-07-28 15:24 ` Jisheng Zhang
2020-07-28 15:25 ` [PATCH 3/4] dt-bindings: regulator: mp886x: support mps,switch-frequency Jisheng Zhang
` (2 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Jisheng Zhang @ 2020-07-28 15:24 UTC (permalink / raw)
To: Liam Girdwood, Mark Brown, Rob Herring, Saravanan Sekar
Cc: linux-kernel, devicetree
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Implement the .set_ramp_delay for MP8867 and MP8869. MP8867 and MP8869
could share the implementation, the only difference is the slew_rates
array.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
drivers/regulator/mp886x.c | 67 ++++++++++++++++++++++++++++++++++++--
1 file changed, 64 insertions(+), 3 deletions(-)
diff --git a/drivers/regulator/mp886x.c b/drivers/regulator/mp886x.c
index 1786f7162019..3c9a6605b115 100644
--- a/drivers/regulator/mp886x.c
+++ b/drivers/regulator/mp886x.c
@@ -18,18 +18,48 @@
#define MP886X_V_BOOT (1 << 7)
#define MP886X_SYSCNTLREG1 0x01
#define MP886X_MODE (1 << 0)
+#define MP886X_SLEW_SHIFT 3
+#define MP886X_SLEW_MASK (0x7 << MP886X_SLEW_SHIFT)
#define MP886X_GO (1 << 6)
#define MP886X_EN (1 << 7)
+struct mp886x_cfg_info {
+ const struct regulator_ops *rops;
+ const int slew_rates[8];
+};
+
struct mp886x_device_info {
struct device *dev;
struct regulator_desc desc;
struct regulator_init_data *regulator;
struct gpio_desc *en_gpio;
+ const struct mp886x_cfg_info *ci;
u32 r[2];
unsigned int sel;
};
+static int mp886x_set_ramp(struct regulator_dev *rdev, int ramp)
+{
+ struct mp886x_device_info *di = rdev_get_drvdata(rdev);
+ const struct mp886x_cfg_info *ci = di->ci;
+ int reg = -1, i;
+
+ for (i = 0; i < ARRAY_SIZE(ci->slew_rates); i++) {
+ if (ramp <= ci->slew_rates[i])
+ reg = i;
+ else
+ break;
+ }
+
+ if (reg < 0) {
+ dev_err(di->dev, "unsupported ramp value %d\n", ramp);
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
+ MP886X_SLEW_MASK, reg << MP886X_SLEW_SHIFT);
+}
+
static int mp886x_set_mode(struct regulator_dev *rdev, unsigned int mode)
{
switch (mode) {
@@ -117,6 +147,21 @@ static const struct regulator_ops mp8869_regulator_ops = {
.is_enabled = regulator_is_enabled_regmap,
.set_mode = mp886x_set_mode,
.get_mode = mp886x_get_mode,
+ .set_ramp_delay = mp886x_set_ramp,
+};
+
+static const struct mp886x_cfg_info mp8869_ci = {
+ .rops = &mp8869_regulator_ops,
+ .slew_rates = {
+ 40000,
+ 30000,
+ 20000,
+ 10000,
+ 5000,
+ 2500,
+ 1250,
+ 625,
+ },
};
static int mp8867_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
@@ -173,6 +218,21 @@ static const struct regulator_ops mp8867_regulator_ops = {
.is_enabled = regulator_is_enabled_regmap,
.set_mode = mp886x_set_mode,
.get_mode = mp886x_get_mode,
+ .set_ramp_delay = mp886x_set_ramp,
+};
+
+static const struct mp886x_cfg_info mp8867_ci = {
+ .rops = &mp8867_regulator_ops,
+ .slew_rates = {
+ 64000,
+ 32000,
+ 16000,
+ 8000,
+ 4000,
+ 2000,
+ 1000,
+ 500,
+ },
};
static int mp886x_regulator_register(struct mp886x_device_info *di,
@@ -183,7 +243,7 @@ static int mp886x_regulator_register(struct mp886x_device_info *di,
rdesc->name = "mp886x-reg";
rdesc->supply_name = "vin";
- rdesc->ops = of_device_get_match_data(di->dev);
+ rdesc->ops = di->ci->rops;
rdesc->type = REGULATOR_VOLTAGE;
rdesc->n_voltages = 128;
rdesc->enable_reg = MP886X_SYSCNTLREG1;
@@ -235,6 +295,7 @@ static int mp886x_i2c_probe(struct i2c_client *client,
if (IS_ERR(di->en_gpio))
return PTR_ERR(di->en_gpio);
+ di->ci = of_device_get_match_data(dev);
di->dev = dev;
regmap = devm_regmap_init_i2c(client, &mp886x_regmap_config);
@@ -259,11 +320,11 @@ static int mp886x_i2c_probe(struct i2c_client *client,
static const struct of_device_id mp886x_dt_ids[] = {
{
.compatible = "mps,mp8867",
- .data = &mp8867_regulator_ops
+ .data = &mp8867_ci
},
{
.compatible = "mps,mp8869",
- .data = &mp8869_regulator_ops
+ .data = &mp8869_ci
},
{ }
};
--
2.28.0.rc0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 3/4] dt-bindings: regulator: mp886x: support mps,switch-frequency
2020-07-28 15:23 [PATCH 0/4] regulator: mp886x: two features and dt json convert Jisheng Zhang
2020-07-28 15:24 ` [PATCH 1/4] dt-bindings: regulator: Convert mp886x to json-schema Jisheng Zhang
2020-07-28 15:24 ` [PATCH 2/4] regulator: mp886x: implement set_ramp_delay Jisheng Zhang
@ 2020-07-28 15:25 ` Jisheng Zhang
2020-07-28 15:26 ` [PATCH 4/4] regulator: mp886x: support setting switch freq Jisheng Zhang
2020-08-03 15:53 ` [PATCH 0/4] regulator: mp886x: two features and dt json convert Mark Brown
4 siblings, 0 replies; 7+ messages in thread
From: Jisheng Zhang @ 2020-07-28 15:25 UTC (permalink / raw)
To: Liam Girdwood, Mark Brown, Rob Herring, Saravanan Sekar
Cc: linux-kernel, devicetree
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Both MP8867 and MP8869 support different switch frequency.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
Documentation/devicetree/bindings/regulator/mps,mp886x.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml b/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
index 500a7b3a59aa..991f2de7eda8 100644
--- a/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
+++ b/Documentation/devicetree/bindings/regulator/mps,mp886x.yaml
@@ -27,6 +27,11 @@ properties:
values R1 and R2 of the feedback voltage divider in kilo ohms.
$ref: "/schemas/types.yaml#/definitions/uint32-array"
+ mps,switch-frequency:
+ description: The valid switch frequency in Hertz.
+ enum: [500000, 750000, 1000000, 1250000, 1500000]
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+
required:
- compatible
- reg
--
2.28.0.rc0
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 4/4] regulator: mp886x: support setting switch freq
2020-07-28 15:23 [PATCH 0/4] regulator: mp886x: two features and dt json convert Jisheng Zhang
` (2 preceding siblings ...)
2020-07-28 15:25 ` [PATCH 3/4] dt-bindings: regulator: mp886x: support mps,switch-frequency Jisheng Zhang
@ 2020-07-28 15:26 ` Jisheng Zhang
2020-08-03 15:53 ` [PATCH 0/4] regulator: mp886x: two features and dt json convert Mark Brown
4 siblings, 0 replies; 7+ messages in thread
From: Jisheng Zhang @ 2020-07-28 15:26 UTC (permalink / raw)
To: Liam Girdwood, Mark Brown, Rob Herring, Saravanan Sekar
Cc: linux-kernel, devicetree
From: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Both MP8867 and MP8869 support different switch frequency.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
---
drivers/regulator/mp886x.c | 42 ++++++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/drivers/regulator/mp886x.c b/drivers/regulator/mp886x.c
index 3c9a6605b115..e3c7813bed4b 100644
--- a/drivers/regulator/mp886x.c
+++ b/drivers/regulator/mp886x.c
@@ -22,10 +22,14 @@
#define MP886X_SLEW_MASK (0x7 << MP886X_SLEW_SHIFT)
#define MP886X_GO (1 << 6)
#define MP886X_EN (1 << 7)
+#define MP8869_SYSCNTLREG2 0x02
struct mp886x_cfg_info {
const struct regulator_ops *rops;
const int slew_rates[8];
+ const int switch_freq[4];
+ const u8 fs_reg;
+ const u8 fs_shift;
};
struct mp886x_device_info {
@@ -60,6 +64,24 @@ static int mp886x_set_ramp(struct regulator_dev *rdev, int ramp)
MP886X_SLEW_MASK, reg << MP886X_SLEW_SHIFT);
}
+static void mp886x_set_switch_freq(struct mp886x_device_info *di,
+ struct regmap *regmap,
+ u32 freq)
+{
+ const struct mp886x_cfg_info *ci = di->ci;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(ci->switch_freq); i++) {
+ if (freq == ci->switch_freq[i]) {
+ regmap_update_bits(regmap, ci->fs_reg,
+ 0x3 << ci->fs_shift, i << ci->fs_shift);
+ return;
+ }
+ }
+
+ dev_err(di->dev, "invalid frequency %d\n", freq);
+}
+
static int mp886x_set_mode(struct regulator_dev *rdev, unsigned int mode)
{
switch (mode) {
@@ -162,6 +184,14 @@ static const struct mp886x_cfg_info mp8869_ci = {
1250,
625,
},
+ .switch_freq = {
+ 500000,
+ 750000,
+ 1000000,
+ 1250000,
+ },
+ .fs_reg = MP8869_SYSCNTLREG2,
+ .fs_shift = 4,
};
static int mp8867_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
@@ -233,6 +263,14 @@ static const struct mp886x_cfg_info mp8867_ci = {
1000,
500,
},
+ .switch_freq = {
+ 500000,
+ 750000,
+ 1000000,
+ 1500000,
+ },
+ .fs_reg = MP886X_SYSCNTLREG1,
+ .fs_shift = 1,
};
static int mp886x_regulator_register(struct mp886x_device_info *di,
@@ -274,6 +312,7 @@ static int mp886x_i2c_probe(struct i2c_client *client,
struct mp886x_device_info *di;
struct regulator_config config = { };
struct regmap *regmap;
+ u32 freq;
int ret;
di = devm_kzalloc(dev, sizeof(struct mp886x_device_info), GFP_KERNEL);
@@ -311,6 +350,9 @@ static int mp886x_i2c_probe(struct i2c_client *client,
config.driver_data = di;
config.of_node = np;
+ if (!of_property_read_u32(np, "mps,switch-frequency", &freq))
+ mp886x_set_switch_freq(di, regmap, freq);
+
ret = mp886x_regulator_register(di, &config);
if (ret < 0)
dev_err(dev, "Failed to register regulator!\n");
--
2.28.0.rc0
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH 0/4] regulator: mp886x: two features and dt json convert
2020-07-28 15:23 [PATCH 0/4] regulator: mp886x: two features and dt json convert Jisheng Zhang
` (3 preceding siblings ...)
2020-07-28 15:26 ` [PATCH 4/4] regulator: mp886x: support setting switch freq Jisheng Zhang
@ 2020-08-03 15:53 ` Mark Brown
4 siblings, 0 replies; 7+ messages in thread
From: Mark Brown @ 2020-08-03 15:53 UTC (permalink / raw)
To: Rob Herring, Saravanan Sekar, Liam Girdwood, Jisheng Zhang
Cc: linux-kernel, devicetree
On Tue, 28 Jul 2020 23:23:27 +0800, Jisheng Zhang wrote:
> This is to improve the mp886x regulator driver support.
> patch1 converts dt binding to json-schema
> patch2 implments .set_ramp_delay
> patch3 and patch3 support the switch freq setting
>
> Jisheng Zhang (4):
> dt-bindings: regulator: Convert mp886x to json-schema
> regulator: mp886x: implement set_ramp_delay
> dt-bindings: regulator: mp886x: support mps,switch-frequency
> regulator: mp886x: support setting switch freq
>
> [...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
Thanks!
[1/4] dt-bindings: regulator: Convert mp886x to json-schema
(no commit info)
[2/4] regulator: mp886x: implement set_ramp_delay
commit: 0eddcf0267f913cb6336af64cadaf5acf6b19b7b
[3/4] dt-bindings: regulator: mp886x: support mps,switch-frequency
(no commit info)
[4/4] regulator: mp886x: support setting switch freq
commit: ee6ad5a24575071b66bd37ffb2d8747a64fcb45f
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
^ permalink raw reply [flat|nested] 7+ messages in thread