[PATCH 0/2] Add support for MMC/SD on j7200-evm

[PATCH 0/2] Add support for MMC/SD on j7200-evm

[Faiz Abbas]

The following patches add dt support for MMC/SD on TI's j7200-evm.

Currently, eMMC support upto HS200 speed and SD card supports upto high
speed speed mode.

These patches depend on:
Lokesh's initial support series
https://patchwork.kernel.org/cover/11740039/
Vignesh's I2C support series
https://lore.kernel.org/patchwork/cover/1282152/
Vignesh's Hyperflash series
https://lore.kernel.org/patchwork/cover/1285326/

Faiz Abbas (2):
  arm64: dts: ti: k3-j7200-main: Add support for MMC/SD controller nodes
  arm64: dts: ti: k3-j7200-common-proc-board: Add support for eMMC and
    SD card

 .../dts/ti/k3-j7200-common-proc-board.dts     | 30 +++++++++++++++
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 37 +++++++++++++++++++
 2 files changed, 67 insertions(+)

-- 
2.17.1

[PATCH 1/2] arm64: dts: ti: k3-j7200-main: Add support for MMC/SD controller nodes

[Faiz Abbas]

Add support for MMC/SD controller nodes present on TI's j7200 SoCs.

There are two nodes:
        1. sdhci0 (8 bit bus width, 200 MHz, HS200, 200 MBps)
        2. sdhci1 (4 bit bus width, 50 MHz, HS, 25 MBps)

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 0a87fa3ea5f0..1702ac0bbf40 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -273,4 +273,41 @@
 		clocks = <&k3_clks 193 1>;
 		power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>;
 	};
+
+	main_sdhci0: sdhci@4f80000 {
+		compatible = "ti,j7200-sdhci-8bit", "ti,j721e-sdhci-8bit";
+		reg = <0x0 0x04f80000 0x0 0x260>, <0x0 0x4f88000 0x0 0x134>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 91 TI_SCI_PD_EXCLUSIVE>;
+		clock-names = "clk_xin", "clk_ahb";
+		clocks = <&k3_clks 91 3>, <&k3_clks 91 0>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-mmc-hs = <0x0>;
+		ti,otap-del-sel-ddr52 = <0x6>;
+		ti,otap-del-sel-hs200 = <0x8>;
+		ti,otap-del-sel-hs400 = <0x0>;
+		ti,strobe-sel = <0x77>;
+		ti,trm-icp = <0x8>;
+		bus-width = <8>;
+		mmc-ddr-1_8v;
+		dma-coherent;
+	};
+
+	main_sdhci1: sdhci@4fb0000 {
+		compatible = "ti,j7200-sdhci-4bit", "ti,j721e-sdhci-4bit";
+		reg = <0x0 0x04fb0000 0x0 0x260>, <0x0 0x4fb8000 0x0 0x134>;
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 92 TI_SCI_PD_EXCLUSIVE>;
+		clock-names = "clk_xin", "clk_ahb";
+		clocks = <&k3_clks 92 2>, <&k3_clks 92 1>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-sd-hs = <0x0>;
+		ti,otap-del-sel-sdr12 = <0xf>;
+		ti,otap-del-sel-sdr25 = <0xf>;
+		ti,otap-del-sel-sdr50 = <0xc>;
+		ti,otap-del-sel-sdr104 = <0x5>;
+		ti,otap-del-sel-ddr50 = <0xc>;
+		no-1-8-v;
+		dma-coherent;
+	};
 };
-- 
2.17.1

[PATCH 2/2] arm64: dts: ti: k3-j7200-common-proc-board: Add support for eMMC and SD card

[Faiz Abbas]

Add support for the eMMC and SD card connected on the common
processor board

sdhci0 is connected to an eMMC while sdhci1 is connected to the
micro SD slot.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
 .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 26ad2e46009e..8e534ef8a3f5 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -28,6 +28,19 @@
 			J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
 		>;
 	};
+
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
+			J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
+			J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+			J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
+			J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
+			J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
+			J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
+			J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -111,3 +124,18 @@
 		#gpio-cells = <2>;
 	};
 };
+
+&main_sdhci0 {
+	/* eMMC */
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_sdhci1 {
+	/* SD card */
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
-- 
2.17.1