From: JC Kuo <jckuo@nvidia.com>
To: <gregkh@linuxfoundation.org>, <thierry.reding@gmail.com>,
<robh@kernel.org>, <jonathanh@nvidia.com>, <kishon@ti.com>
Cc: <linux-tegra@vger.kernel.org>, <linux-usb@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<nkristam@nvidia.com>, JC Kuo <jckuo@nvidia.com>
Subject: [PATCH v5 00/16] Tegra XHCI controller ELPG support
Date: Thu, 19 Nov 2020 16:53:49 +0800 [thread overview]
Message-ID: <20201119085405.556138-1-jckuo@nvidia.com> (raw)
Tegra XHCI controler can be placed in ELPG (Engine Level PowerGated)
state for power saving when all of the connected USB devices are in
suspended state. This patch series includes clk, phy and pmc changes
that are required for properly place controller in ELPG and bring
controller out of ELPG.
JC Kuo (16):
clk: tegra: Add PLLE HW power sequencer control
clk: tegra: Don't enable PLLE HW sequencer at init
phy: tegra: xusb: Move usb3 port init for Tegra210
phy: tegra: xusb: tegra210: Do not reset UPHY PLL
phy: tegra: xusb: Rearrange UPHY init on Tegra210
phy: tegra: xusb: Add Tegra210 lane_iddq operation
phy: tegra: xusb: Add sleepwalk and suspend/resume
soc/tegra: pmc: Provide USB sleepwalk register map
arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop
dt-bindings: phy: tegra-xusb: Add nvidia,pmc prop
phy: tegra: xusb: Add wake/sleepwalk for Tegra210
phy: tegra: xusb: Tegra210 host mode VBUS control
phy: tegra: xusb: Add wake/sleepwalk for Tegra186
arm64: tegra210/tegra186/tegra194: XUSB PADCTL irq
usb: host: xhci-tegra: Unlink power domain devices
xhci: tegra: Enable ELPG for runtime/system PM
.../phy/nvidia,tegra124-xusb-padctl.txt | 1 +
arch/arm64/boot/dts/nvidia/tegra186.dtsi | 1 +
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 1 +
arch/arm64/boot/dts/nvidia/tegra210.dtsi | 2 +
drivers/clk/tegra/clk-pll.c | 12 -
drivers/clk/tegra/clk-tegra210.c | 53 +-
drivers/phy/tegra/xusb-tegra186.c | 558 ++++-
drivers/phy/tegra/xusb-tegra210.c | 1889 +++++++++++++----
drivers/phy/tegra/xusb.c | 92 +-
drivers/phy/tegra/xusb.h | 22 +-
drivers/soc/tegra/pmc.c | 94 +
drivers/usb/host/xhci-tegra.c | 613 ++++--
include/linux/clk/tegra.h | 4 +-
include/linux/phy/tegra/xusb.h | 10 +-
14 files changed, 2787 insertions(+), 565 deletions(-)
--
2.25.1
next reply other threads:[~2020-11-19 8:54 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-19 8:53 JC Kuo [this message]
2020-11-19 8:53 ` [PATCH v5 01/16] clk: tegra: Add PLLE HW power sequencer control JC Kuo
2020-11-19 8:53 ` [PATCH v5 02/16] clk: tegra: Don't enable PLLE HW sequencer at init JC Kuo
2020-11-19 8:53 ` [PATCH v5 03/16] phy: tegra: xusb: Move usb3 port init for Tegra210 JC Kuo
2020-11-19 8:53 ` [PATCH v5 04/16] phy: tegra: xusb: tegra210: Do not reset UPHY PLL JC Kuo
2020-11-19 8:53 ` [PATCH v5 05/16] phy: tegra: xusb: Rearrange UPHY init on Tegra210 JC Kuo
2020-11-19 8:53 ` [PATCH v5 06/16] phy: tegra: xusb: Add Tegra210 lane_iddq operation JC Kuo
2020-11-19 8:53 ` [PATCH v5 07/16] phy: tegra: xusb: Add sleepwalk and suspend/resume JC Kuo
2020-11-19 8:53 ` [PATCH v5 08/16] soc/tegra: pmc: Provide USB sleepwalk register map JC Kuo
2020-11-19 8:53 ` [PATCH v5 09/16] arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop JC Kuo
2020-11-19 8:53 ` [PATCH v5 10/16] dt-bindings: phy: tegra-xusb: Add nvidia,pmc prop JC Kuo
2020-11-30 22:03 ` Rob Herring
2020-11-19 8:54 ` [PATCH v5 11/16] phy: tegra: xusb: Add wake/sleepwalk for Tegra210 JC Kuo
2020-11-19 8:54 ` [PATCH v5 12/16] phy: tegra: xusb: Tegra210 host mode VBUS control JC Kuo
2020-11-19 8:54 ` [PATCH v5 13/16] phy: tegra: xusb: Add wake/sleepwalk for Tegra186 JC Kuo
2020-11-19 8:54 ` [PATCH v5 14/16] arm64: tegra210/tegra186/tegra194: XUSB PADCTL irq JC Kuo
2020-11-19 8:54 ` [PATCH v5 15/16] usb: host: xhci-tegra: Unlink power domain devices JC Kuo
2020-11-19 8:54 ` [PATCH v5 16/16] xhci: tegra: Enable ELPG for runtime/system PM JC Kuo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201119085405.556138-1-jckuo@nvidia.com \
--to=jckuo@nvidia.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jonathanh@nvidia.com \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=nkristam@nvidia.com \
--cc=robh@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).